схема и сервис мануал на английском Samsung 710V шасси GS17VS PDF
схема и сервис мануал на английском Samsung 710V шасси GS17VS PDF
схема и сервис мануал на английском Samsung 710V шасси GS17VS PDF
Chassis Model
GS17VS 710V
GS17VT 73V
GS19VS 910V
GS19VT 93V
GS15MS 510M
GS17MS 710 M
GS19MS 910M
SERVICE Manual
TFT-LCD MONITOR CONTENTS
1. Precautions
2. Product Specifications
5. Troubleshooting
8. Block Diagram
9. Wiring Diagram
GS17VS/GS19VS GS17VT
Samsung Electronics Co.,Ltd.
❈ This Service Manual is a property of Samsung 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Kyungki-Do, Korea,443-742
Electronics Co., Ltd. Printed in Korea
Any unauthorized use of Manual can be punished P/N : BN82-00087Q-00
under applicable International and/or domestic law. http://itself.sec.samsung.co.kr
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1-1 Warnings
1. For continued safety, do not attempt to modify the
(READING SHOULD
circuit board. NOT BE ABOVE 0.5mA)
Before returning the monitor to the user, perform the Figure 1-1. Leakage Current Test Circuit
following safety checks:
1. Inspect each lead dress to make certain that the 4. With the unit completely reassembled, plug the AC
leads are not pinched or that hardware is not line cord directly into a 120V AC outlet. With the
lodged between the chassis and other metal parts in unit’s AC switch first in the ON position and then
the monitor. OFF, measure the current between a known earth
2. Inspect all protective devices such as nonmetallic ground (metal water pipe, conduit, etc.) and all
control knobs, insulating materials, cabinet backs, exposed metal parts, including: metal cabinets,
adjustment and compartment covers or shields, screwheads and control shafts. The current
isolation resistor-capacitor networks, mechanical measured should not exceed 0.5 milliamp. Reverse
insulators, etc. the power-plug prongs in the AC outlet and repeat
3. Leakage Current Hot Check (Figure 1-1): the test.
WARNING:
Do not use an isolation transformer during this test. 1-1-4 Product Safety Notices
Use a leakage current tester or a metering system Some electrical and mechanical parts have special
that complies with American National Standards safety-related characteristics which are often not
Institute (ANSI C101.1, Leakage Current for evident from visual inspection. The protection they give
Appliances), and Underwriters Laboratories (UL may not be obtained by replacing them with
Publication UL1410, 59.7). components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by
! on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and/or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
GS17VS/GS17VT/GS19VS/GS19VT/ 1-1
GS15MS/GS17MS/GS19MS
1 Precautions
1. Immediately before handling any semiconductor 6. Do not remove a replacement ESD from its
components or assemblies, drain the electrostatic protective package until you are ready to install it.
charge from your body by touching a known earth Most replacement ESDs are packaged with leads
ground. Alternatively, wear a discharging wrist- that are electrically shorted together by conductive
strap device. To avoid a shock hazard, be sure to foam, aluminum foil or other conductive materials.
remove the wrist strap before applying power to 7. Immediately before removing the protective
the monitor. material from the leads of a replacement ESD,
2. After removing an ESD-equipped assembly, place it touch the protective material to the chassis or
on a conductive surface such as aluminum foil to circuit assembly into which the device will be
prevent accumulation of an electrostatic charge. installed.
3. Do not use freon-propelled chemicals. These can Caution: Be sure no power is applied to the
generate electrical charges sufficient to damage chassis or circuit and observe all
ESDs. other safety precautions.
4. Use only a grounded-tip soldering iron to solder or
desolder ESDs. 8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
5. Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from
solder removal devices not classified as “anti-static” a carpeted floor can generate enough static
can generate electrical charges sufficient to damage electricity to damage an ESD.
ESDs.
1-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
2 Product Specifications
2-1 GS17VS/GS17VT Specifications
Description
Item
GS17VS GS17VT
LCD Panel TFT-LCD panel, RGB vertical stripe, normally black transmissive,
17-Inch viewable, 0.264 (H) x 0.264 (V) mm pixel pitch
Active Display
Horizontal/Vertical 338 ± 3 mm / 270 ± 3 mm
Dimensions
Set (W x D x H) 15.0 x 2.4 x 12.6 Inches (382.0 x 62.0 x 319.0 mm) State of stand disassembled 15.0 x 2.4 x 12.7Inches (380.0 x 60.0 x 322.0 mm) State of stand disassembled
15.0 x 4.4 x 15.1 Inches (382.0 x 175.0 x 383.7 mm) State of stand installed 15.0 x 6.9 x 15.1 Inches (380.0 x 175.0 x 383.5 mm) State of stand installed
Package 18.2 x 17.8 x 5.6 Inches (463 x 452 x 141 mm) 18.2 x 5.6 x 17.8 Inches (463 x 141 x 452 mm)
Weight (Set/Package) 4.55 kg (10.0 lbs) / 5.65 kg (12.5 lbs) 4.55 kg (10.0 lbs) / 5.65 kg (12.5 lbs)
GS17VS/GS17VT/GS19VS/GS19VT/ 2-1
GS15MS/GS17MS/GS19MS
2 Product Specifications
Description
Item
GS15MS GS17MS
LCD Panel TFT-LCD panel, RGB vertical stripe, normally black transmissive, TFT-LCD panel, RGB vertical stripe, normally black transmissive,
15-Inch viewable, 0.297 (H) x 0.297 (V) mm pixel pitch 17-Inch viewable, 0.264 (H) x 0.264 (V) mm pixel pitch
Scanning Frequency Horizontal : 31 kHz ~ 60 kHz (Automatic) Horizontal : 30 kHz ~ 81 kHz (Automatic)
Vertical : 50 Hz ~ 75 Hz Vertical : 56 Hz ~ 75 Hz
Active Display
Horizontal/Vertical 304.1 mm / 228.1 mm 338 ± 3 mm / 270 ± 3 mm
AC power voltage & Frequency AC 90 ~ 264 Volts, 60/50 Hz ± 12V / 3A AC 90 ~ 264 Volts, 60/50 Hz ± 3 Hz
Dimensions
Set (W x D x H) 14.0 x 2.2 x 12.0 Inches (353.9 x 57.0 x 304.7 mm) State of stand disassembled 15.0 x 2.4 x 13.5 Inches (381.9 x 62.0 x 342.9 mm) State of stand disassembled
14.0 x 6.9 x 13.6 Inches (353.9 x 175.0 x 344.7 mm) State of stand installed 15.0 x 6.9 x 15.1 Inches (381.9 x 175.0 x 383.9 mm) State of stand installed
Package 17.0 x 16.3 x 4.9 Inches (433 x 413 x 125 mm) 18.2 x 17.8 x 5.6 Inches (463 x 452 x 141 mm)
Weight (Set/Package) 3.0 kg (6.6 lbs) / 3.8 kg (8.4 lbs) 4.5 kg (9.9 lbs) / 5.6 kg (12.3 lbs)
Environmental Considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating Humidity : 10 % ~ 80 %
Storage Temperature : -13°F ~ 113°F (-25°C ~ 45°C)
Storage Humidity : 5 % ~ 95 %
2-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
2 Product Specifications
Description
Item
GS19VS GS19VT
LCD Panel TFT-LCD panel, RGB vertical stripe, normally black transmissive,
19-Inch viewable, 0.298 (H) x 0.298(V) mm pixel pitch
Active Display
Horizontal/Vertical 376.32 ± 3 mm / 301.056 ± 3 mm
Dimensions
Set (W x D x H) 16.9 x 2.4 x 14.0 Inches (428.0 x 61.8 x 356.0 mm) State of stand disassembled 16.9 x 2.4 x 14.0 Inches (428.0 x 61.8 x 356.0 mm) State of stand disassembled
16.9 x 7.7 x 16.9 Inches (428.0 x 195.7 x 430.0 mm) State of stand installed 16.9 x 8.0 x 17.0 Inches (428.0 x 204.0 x 433.0 mm) State of stand installed
Package 20.9 x 19.4 x 5.9 Inches (531 x 494 x 150 mm) 20.8 x 20.1 x 9.0 Inches (529 x 510 x 229 mm)
Weight (Set/Package) 5.55 kg (12.2 lbs) / 6.95 kg (15.3 lbs) 6.4 kg (14.1 lbs) / 8.2 kg (18.1 lbs)
GS17VS/GS17VT/GS19VS/GS19VT/ 2-3
GS15MS/GS17MS/GS19MS
2 Product Specifications
Item Description
LCD Panel TFT-LCD panel, RGB vertical stripe, normally black transmissive,
19-Inch viewable, 0.298 (H) x 0.298(V) mm pixel pitch
Active Display
Horizontal/Vertical 376.32 ± 3 mm / 301.056 ± 3 mm
Dimensions
Set (W x D x H) 16.9 x 2.4 x 15.0 Inches (428.0 x 61.8 x 380.5 mm) State of stand disassembled
16.9 x 7.7 x 16.9 Inches (428.0 x 195.7 x 430.0 mm) State of stand installed
Package 20.9 x 19.4 x 5.9 Inches (531 x 494 x 150 mm)
Weight (Set/Package) 5.75 kg (12.7 lbs) / 7.55 kg (16.6 lbs)
2-4 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
2 Product Specifications
GS17VS/GS17VT/GS19VS/GS19VT/ 2-5
GS15MS/GS17MS/GS19MS
2 Product Specifications
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
Sync-on-Green
Sync
Sync Sync
Sync Vertical
Green
BB PP
Horizontal
AA O O P Q R S
B O
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
2-6 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the
GS17VS/GS17VT/GS19VS/GS19VT/GS15MS/GS17MS/GS19MS TFT-LCD monitors.
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. Follow these directions carefully; never use any metal instrument except provided jig to
separate the cabinet.
3. R/Cover opening jig : BH81-00001A
3-1 GS17VS/GS17VT/GS19VS/GS19VT
1. Place monitor face down on cushioned table.
Remove 4 screws from grip on the stand and
remove the stand.
GS17VS/GS17VT/GS19VS/GS19VT/ 3-1
GS15MS/GS17MS/GS19MS
3 Disassembly and Reassembly
3-2 GS15MS/GS17MS/GS19MS
1. Place monitor face down on cushioned table.
Remove 4 screws from grip on the stand and
remove the stand. Remove 2 screws from the
rear cover.
3-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
3 Disassembly and Reassembly
3-3 Reassembly
GS17VS/GS17VT/GS19VS/GS19VT/ 3-3
GS15MS/GS17MS/GS19MS
3 Disassembly and Reassembly
Memo
3-4 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
4 Alignments and Adjustments
This section of the service manual explains how to use the RS232 JIG.
This function is needed for AD board change and program memory (IC110) change.
Figure 1.
4-4 OSD Adjustment When Replacing Panel
1. Adjust brightness and contrast to 0. Then, press the ( Enter/Auto key) for 5 second.
Service function OSD will appear on screen.
2. Press the + key to place the cursor on the panel. Press the menu key for 5 seconds.
❇ Note : Please be sure to read the following instructions for details on service function.
GS17VS/GS17VT/GS19VS/GS19VT/ 4-1
GS15MS/GS17MS/GS19MS
4 Alignments and Adjustments
Panel Information
Softward Version
Checksum
Figure 3.
4-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
4 Alignments and Adjustments
Figure 4.
Figure 5, 6.
GS17VS/GS17VT/GS19VS/GS19VT/ 4-3
GS15MS/GS17MS/GS19MS
4 Alignments and Adjustments
Memo
4-4 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
5 Troubleshooting
Yes
Yes
Yes
Yes
GS17VS/GS17VT/GS19VS/GS19VT/ 5-1
GS15MS/GS17MS/GS19MS
5 Troubleshooting
Yes
Yes
Yes
5-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
5 Troubleshooting
Yes
Yes
Yes
Yes
GS17VS/GS17VT/GS19VS/GS19VT/ 5-3
GS15MS/GS17MS/GS19MS
5 Troubleshooting
1
Check signal cable connection and power.
No
1 X400 oscillate properly? Replace or check related circuit.
Yes
2
Is there R, G, B input at R100, No
Check input part.
R101 and R103?
Yes
Yes
Yes
Yes
5-4 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
6 Exploded View and Parts List
❈ You can search for updated part codes through ITSELF web site.
URL : http://itself. sec. samsung.co.kr
6-1 GS17VS
GS17VS/GS17VT/GS19VS/GS19VT/ 6-1
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
6-2 GS17VT
6-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
6-3 GS19VS
GS17VS/GS17VT/GS19VS/GS19VT/ 6-3
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
6-4 GS19VT
6-4 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
6-5 GS15MS
GS17VS/GS17VT/GS19VS/GS19VT/ 6-5
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
6-6 GS17MS
6-6 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
6-7 GS19MS
GS17VS/GS17VT/GS19VS/GS19VT/ 6-7
GS15MS/GS17MS/GS19MS
6 Exploded View & Parts List
Memo
6-8 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
7 Electrical Parts List
0 GS17VSSSY/EDC 701N,GS17V,17,LCD-MO,NETHERLANDS 0
7-1
7 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
7-2
7 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
7-3
7 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
7-4
7 Electrical Parts List
7-2 GS17VTSN/EDC
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
0 GS17VTSN/EDC 73V,GS17V,17,LCD-MO,NETHERLANDS 0
7-5
7 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
7-6
7 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
7-7
7 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
7-8
R
GS15MS/GS17MS/GS19MS
8 Block Diagram
G A DC/
GS17VS/GS17VT/GS19VS/GS19VT/
B IM A GE SCA L ER/ L V DS
H- sy nc (SE7889) L
8-1 ANALOG Blcok Diagram
V - sy nc C
D
12MHz
+ 13V P
S + 13V A
M + 5V M ICOM N
P + 5V E
S + 0~ 3.3 L
(ON)+ 5V
IP BOARD
IN V ERT ER
8-1
8 Block Diagrams
Memo
8-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
10 PCB Layout
10-1 GS15MS AUDIO PCB
TRANSISTOR
Q600 TR-SMALL SIGNAL 22.1 62.0
GS17VS/GS17VT/GS19VS/GS19VT/ 10-1
GS15MS/GS17MS/GS19MS
10 PCB Layout
IC
IC105 DIODE-TVS 55.0 14.0
IC106 DIODE-TVS 110.7 12.9
IC200 IC-MICROCONTROLLER 96.6 30.9
IC201 IC-EEPROM 95.2 8.5
IC400 IC-LCD CONTROLLER 56.0 46.9
IC600 FET-SILICON 27.5 55.8
IC601 IC-DUAL VOLTAGE REGULATOR 17.4 35.5
10-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
10 PCB Layout
TRANSISTOR
Q600 TR-SMALL SIGNAL 22.1 62.0
GS17VS/GS17VT/GS19VS/GS19VT/ 10-3
GS15MS/GS17MS/GS19MS
10 PCB Layout
Memo
10-4 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
+5V
+5V
GND
GND
GND
+14V
+14V
BL_EN
ADJ_BL
GS15MS/GS17MS/GS19MS
9 Wiring Diagram
GS17VS/GS17VT/GS19VS/GS19VT/
CN600
NC
GND
RxE3+
CN400
RxE3-
GND
RxEC+
RxEC-
GND
RxE2+
RxE2-
GND
RED_IN
RxE1+
GREEM_IN
BLUE_IN RxE1-
CN101
GND
GND
RxE0+
GND
RxE0-
R_GND
RxO3+
G_GND
RxO3-
B_GND
RxOC+
NC
RxOC-
CHK_DSUB
GND
GND RxO2+
SDA_DDC
RxO2-
HSYNC_IN
RxO1+
VSYNC_IN RxO1-
SCL_DDC RxO0+
RxO0-
+5v
+5v
+5v
VCC
LED_GRN
NC
CN200
Key 2
Key 1
GND
CN500
OUT1-
OUT2-
OUT1+
OUT2+
AMP_L
A_GND
AMP_R
9-1
9 Wiring Diagram
Memo
9-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS
11 Schematic Diagrams
❈ This Document can not be used without Samsung’s authorization.
+5V_IN VCC_MCU +5V_IN
VCC_MCU +5V_IN
Vcc_PANEL_IN R200
0
1/16W
15" : +3.3V In
4.7K
4.7K
OEM OPTION
4.7K
RxOC+
RxEC+
RxO0+
RxO1+
RxO2+
RxOC-
RxE2+
RxE3+
RxEC-
RxO0-
RxO1-
RxO2-
RxE2-
RxE3-
4.7K
4.7K
4.7K
4.7K
4.7K
4.7K
4.7K
4.7K
RxO3+
RxE0+
RxE1+
RxO3-
RxE0-
RxE1-
10K
10K
1/16W
GND
GND
GND
GND
GND
GND
NC
1/16W
5V
5V
5V
1/16W
470
R246
C201 C200
100nF
Vcc_PANEL CN400 OEM OPTION 10000nF M/M OPTION
R203
R214
R205
R208
R209
R206
R207
R210
R212
R211
16V
R204
R216
R217
10V
4.7K
MGND2 MGND1
10K
12505WR-30A01
1K
GOYA 2 M/M Only (Option) MO
+5V(17"/19")/+3.3V(15") R213
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
10
11
9
8
7
6
5
4
3
2
1
10K
1/16W
+14V_IN
R202
R600
+14V_AUDIO
R241
R221
R238
10K 470
1/16W R250
0
AUDIO_EN C401 1/16W
M/M OPTION
C600
IC600 100uF AUDIO_EN
1uF R220 4.7K
Q600 10V SUPLECODE M/M OPTION
C400 R400 PANEL_EN
B
2SC2412K-Q MO 1 R219 R222
S1 D1 8 100nF 2Kohm
HC-49/S-SMD(12MHz,30ppm)
10K
C
2 D1_1 7 4.7K
G1 16V
3 6 MO R218 100 1/16W VSYNC_IN_A
R601 S2 D2
4 D2_1 5
15K G2 HSYNC_IN_A
R215 100 1/16W
X200 CHK_DSUB
C205 CHK_DVI
Q0
10000nF
C204 50V AUDIO_VOL
C601 22pF 10V
R602 C602 MO R245 4.7K R249
100uF MO R248
M/M OPTION
10K 25V 10nF 0
Q1
C603 6 5 4 3 2 1 44 43 42 41 40 24Kohm
1/16W 50V C208 C202 1/16W 1/10W
1uF C207 C206
100nF
V33
HSYNCI
PC4
PC5
VSYNCI
Audio Line(25V Cap)
RSTB
MO
CVV
100nF 1uF
PC0
PC1
PC2
PC3
Reserved 22pF 7 39
GND NC2 25V 25V
8 38
OSCO NC1
PANEL_EN
GOYA 2 M/M Only (Option) +3.3V_MAIN XTL_OUT
9
10
OSCI PC6
37
36 NVRAM_CON
P30 PC7
11 35 DDC_CON
R225 100 12
P31 IC200 PD0
34 BL_EN
WR P34 PD1
R226 100 13 33
PB7
PB6
PB5
PB4
PA7
PA6
PA5
PA4
PA3
PA2
PA1
MST9131B
R231 100
ALE
18 19 20 21 22 23 24 25 26 27 28
R237 100
R233
AD0
+14V_IN +5V_IN 3Kohm
16V
100nF
1/10W
C402
+3.3V_MAIN R232 100
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
R234 100 SCL_DDC_D
ADJ_BL
C403 C405 C406 C404 R243 470 1/16W SDA_DDC_D
LVBCKM
LVBCKP
AVSS_MPLL
GNDC
LVACKM
GNDP
GNDP
GNDP
GNDP
VDDC
VDDP
VDDP
LVACKP
VDDP
LVB0M
LVB1M
LVB2M
LVB3M
LVB0P
LVB1P
LVB2P
LVB3P
LVA0M
LVA1M
LVA2M
LVA3M
LVA0P
LVA1P
LVA2P
LVA3P
100nF 100nF 100nF 100nF LED_GREEN R235 100
16V 16V 16V 16V
R236 100 SCL_DDC_A
81
VDDC
50
C407 C408 C409 C410 C411 C412 SDA_DDC_A
BYPASS GNDC 100nF 100nF 100nF 100nF 100nF 100nF
82 BUSTYPE 49 R239 100
GNDP 16V 16V 16V 16V 16V 16V AD1
C414 +3.3V_MAIN 83
84
NC
NC
VDDP
48
47
R240
R242
100
100 AD2
100nF VDDC AD3
85 NC 46 C413
16V GNDC
MO
86
87
NC
VDDC GNDP
45
44
100nF VCC_MCU
XTL_OUT GNDC VDDP 16V
1 TP600 1 88 43
GNDP NC
2
89
90
VDDP SE7888/SE7889 AD2
42
41 AD2
1 AD1
UDZS5.6B-TE-17
C416 NC AD1
91 40
To IP Board
TP601 1 18pF NC NC
3 92 39
AD0 AD0 NC
ZD600
5 96 35 MO
AVDD_MPLL RIZ_SCL RD 1/16W
6
TP602 1
X400 97
98 AVSS_MPLL
HSYNC0
WRZ_SDA
34
ALE_CS 33
WR
ALE
1
2
8
7 R247 100 NVRAM_CON
AVDD_PLL
Q1
AVDD_DVI
AVDD_DVI
AVSS_PLL
AVSS_DVI
AVSS_DVI
AVSS_DVI
99 32 3 6
SCL_MCU
VSYNC0
AVSS
SOGIN0
RINOM
7 4 5 100
GIN0M
RINOP
100 31
BIN0M
R223
GIN0P
BIN0P
REFM
AVDD
AVDD
REXT
REFP
AVSS
AVSS
HC-49/S-SMD(12MHz,30ppm)
+3.3V_MAIN +3.3V_MAIN SDA_MCU
CK+
CK-
C418
G+
R+
B+
G-
R-
TP603
B-
8 1
ADJ_BL 18pF R224 100
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
11
1
2
3
4
5
6
7
8
9
TP604 50V
9 1
BL_EN +3.3V_MAIN C419
100nF
slcon9p C606 R603 C420
C605 16V
CN600 100
1uF 100nF 100nF
1/16W
10V 16V 16V
MO C421
100nF
16V GOYA 2 M/M Only (Option)
2
TDA7053A
A_GND slcon9p
1 16 TP500 1 1
N.C.
2 OUT1+ 15
VC1
D600 GF1G/17
1 VOUT1
GND
8 C609 C608 AUDIO_VOL 3
N.C.
N.C. 14 TP501 1 2
PGND1
2 7 100nF R504 51Kohm C502 1uF 4 VI(1) 13
3
VIN GND 100uF C607
3
VIN GND
6
100uF
AMP_R 1/10W 5
VP
OUT1- 12
OUT2-
TP502 1 3
*Drop Voltage* 4 5 R505 51Kohm C503 1uF 6 VI(2) 11
0.8Vmax
GND
VOUT2 16V AMP_L 1/10W 7 SGND N.C. 10
PGND2
TP503 1
4
IC601 8 VC2 9
OUT2+ TP504 1 5
C610 R501 1201-001805
C104 C105 C101 C102 C103 C100 5.1K
100nF R500 R506 TP505 1 6
100nF 100nF 100nF 100nF 100nF 100nF
APL5522KCTR
16V 16V 16V 16V 16V 16V
1/16W
5.1K
24Kohm
1/10W
AMP_R
TP506 1 7
RXC-
RX2-
RX1-
RX0-
10nF
R502 0 A_GND
A_GND
UDZS5.6B-TE-17
1
5.2V ~ 6.0V
FT600 C107
C108 C109 R503 0
A 1
15pF
D100
15pF SOG
15pF
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
B
2
MO R106 MO D101
17"/19" Only(Option) +3.3V_MAIN MO
390ohm MMBD4148SE
22ohm
22ohm
22ohm
22ohm
22ohm
22ohm
22ohm
22ohm
B 2
C
3
C110
HSYNC_IN_A
VSYNC_IN_A
IC602 D102
SDA_DDC_A
SCL_DDC_A
CHK_DSUB
MMBD4148SE 100nF
AP1117D-33A
1
A
UDZS5.6B-TE-17
3 4 16V
R110
R112
R113
R114
R115
R116
R117
OUT
R111
IN
G+IN_A
R+IN_A
B+IN_A
G-IN_A
R-IN_A
B-IN_A
C111
1 B 2
GND
3
D114
100nF
B 2
C611
C
3
1
C612 16V
A
100uF
RX1+
RX0+
RX0-
RXC+
RXC-
RX2+
RX2-
RX1-
HSYNC_IN_A
VSYNC_IN_A
100uF MO
SDA_DDC_D
1
SCL_DDC_D
D103
A
16V
15" Only(Option) C112
D104 MMBD4148SE
CHK_DVI
100nF
C
B 2
16V
C113 MMBD4148SE VCC_MCU
1
A
100nF
1 B 2
16V
3
C
MO
D105
A
MMBD4148SE
100
75
75
D106
+5V_DDC_D
100
C114
1 B 2
C115
C
3
C119 50V
G-IN_A
B+IN_A
G+IN_A
50V
R+IN_A
50V 50V
B-IN_A
R118
R-IN_A
R119
MO
R120
100nF
R121
MO MO MO CN200
To Function PCB
16V
MO 12507WR-06L
1
TP200
1K
D107 1
TP201
1 B 2
LED_GREEN 1
C
R124
100nF MMBD4148SE 4.7K 10K 3 MGND1
TP202
KEY2 1 4
A
D108
+5V_DDC_D +5V_IN C224 C221
10nF
C222
10nF
1
1 B 2
100nF
3
C123
C
50V 50V
UDZS5.6B-TE-17
25V
C2
C1
C2
C1
1
A1
A1
100nF MMBD4148SE
3
2
MO MO
A
16V MO
ZD200
MO D110 D109
UDZS5.6B-TE-17 UDZS5.6B-TE-17
IC107
1
D111MMBD4148SE R125 B A B 2
C2
C1
A1
MMQA5V6T3
1
C125 1K 2 A
1
C3
1 B 2
1/16W
C
100nF
1
C4
C4
3
A2
A2
4
6
1
16V 1 IC106
1
5.32V ~ 5.88 C126 IC105
A
8
1
7
15K 15K
*Operating Range* 16V 5.32V ~ 5.88 MMQA5V6T3
1 8 1/16W 1/16W
C4
A2
10
MO
6
12
13
14
15
11
1
9
2
6
2 7
C3
2.5V ~ 5.5V CN101
D112 3 6
C127 SCL_DDC_D
1
5 d_sub15p
C
B 2
4
3
100nF
SDA_DDC_D
16V MMBD4148SE
TP43
U2
1
A
C
3
100nF
TP49
TP48
TP41
10K
TP40
TP39
TP44
16V
1/16W
MO
D115
C
19
14
11
B
17
10
18
12
20
13
21
22
15
23
16
1
7
9
24
25
26
4
DDC_CON
R132
E Q100
2SC2412K-Q 100
CN102
DVI-D SUB
tpcon26p
GS17VS/GS17VT/GS19VS/GS19VT/ 11-1
GS15MS/GS17MS/GS19MS
11 Schematic Diagrams
1 2 3
11-2 GS17VS/GS17VT/GS19VS/GS19VT/
GS15MS/GS17MS/GS19MS