Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 108 views

    300 Ohm Twin-Lead J-Pole Portable Antenna

    Uploaded by

    kc0fzz
    The twinlead j-pole is a very compact, pocket-sized antenna. It provides about 3 db of gain with a low take-off angle. It can be built in no time flat for a few dollars of readily available materials.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    300 Ohm Twin-Lead J-Pole Portable Antenna

    Uploaded by

    kc0fzz
    108 views3 pages
    The twinlead j-pole is a very compact, pocket-sized antenna. It provides about 3 db of gain with a low take-off angle. It can be built in no time flat for a few dollars of readily available materials.

    Original Title

    twinlead

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The twinlead j-pole is a very compact, pocket-sized antenna. It provides about 3 db of gain with a low take-off angle. It can be built in no time flat for a few dollars of readily available materials.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    108 views3 pages

    300 Ohm Twin-Lead J-Pole Portable Antenna

    Uploaded by

    kc0fzz
    The twinlead j-pole is a very compact, pocket-sized antenna. It provides about 3 db of gain with a low take-off angle. It can be built in no time flat for a few dollars of readily available materials.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    300 Ohm Twin-Lead J-Pole

    Portable Antenna

    This is a popular 2-meter emergency antenna that can be found


    all over the internet and in antenna books. I simply followed the
    attached instructions, cut a piece of twin-lead in the right places
    and hooked up some coax. It’s fast, easy and works! Here is
    the picture of the antenna I built February 12th 2004 for the
    upcoming Baltimore/Harford County Mutual Aid Drill.

    - Dave KB3KAI
    dave@kb3kai.com
    The Twinlead J-Pole
    Craig LaBarge, WB3GCK

    In an emergency situation, it is often necessary to squeeze every bit of performance possible out of a 2
    meter HT. One way to do that is to replace that little rubber duck antenna with the ever-popular
    Twinlead J-Pole. This simple antenna lends itself well to emergency use or as a portable antenna for
    hotel room operations while traveling.

    There are several features which make the ubiquitous Twinlead J-Pole antenna a good addition to your
    emergency grab-n-go kit. When rolled up, it is an extremely compact, pocket-sized antenna. In use, it
    makes for a very effective antenna and provides about 3 db of gain with a low take-off angle. In fact,
    when used on your HT, it will dramatically out-perform your rubber duckie. And finally, it can be built
    in no time flat for a few dollars of readily available materials.

    Technically-speaking, the J-Pole is an end-fed, halfwave antenna with a quarterwave matching section
    to allow feeding with 50-ohm coax. Being a halfwave antenna, it is not dependent on a ground or radials
    for proper performance. That's also a plus for portable operation.

    Here's what you'll need to build one for the 2 meter band:

    z A 60-inch piece of flat TV twinlead. Use the inexpensive Radio Shack twinlead. Don't use the
    more expensive foam-filled line.
    z 6 feet or more of coax cable. RG-174/U miniature cable makes for a very portable antenna but
    don't use more than 6 feet of it; it's very lossy. Use RG-58/U if you like, but it will be a bit
    bulkier.
    z Ferrite bead, type 43 material (optional - see below)
    z BNC connector (or other connector of your choice)

    Here's how you build it:

    z First, take the 60 inch piece of twinlead and strip back about 1/2 inch from one end. Twist and
    solder the two wires together. Keep the connection as short as possible. This will be the bottom of
    the antenna.
    z Next, measure up 1-1/4 inches from the bottom and carefully remove the insulation, exposing
    both wires, as shown in Figure 1. Keep the notches small (1/8" or so) and be careful not to cut the
    wires. This is where we will be attaching the coax later.
    z Now, attach your coax as shown in Figure 1. [Note: A ferrite bead (type 43 material) can be
    placed over the outside of the coax near the feedpoint to choke off any RF that might get coupled
    onto the coax shield. Many plans for this antenna, however, omit the ferrite bead. Your choice. If
    you experience problems with RF on the rig, go ahead and add the ferrite bead. Alternately, you
    can wind the coax into a coil of about 5 inches in diameter with 4 turns to create a suitable RF
    choke.]
    z Measure up 15-1/4 inches from the point where the coax braid is attached and make a 1/4-inch
    notch. This time, you want to cut through the wire. Only cut one notch and make sure it is on the
    side where the braid is attached. This will form the 1/4 wave matching section.
    z Tape the coax to the twinlead for strain relief. Also, tape all solder connections and add some tape
    at the 1/4-inch notch for added strength.
    z Now, measure up from the bottom of the antenna and cut it to an overall length of 54 inches.

    That's about all there is to it. To facilitate hanging, punch a small hole in the top of the antenna. Use
    monofilament fishing line or other non-conductive line through the hole for hanging. The J-Pole is very
    broad-banded, so it shouldn't require any tuning. (An SWR check, however, is recommended.) Just
    unroll it, hang it up, and communicate.

    © 1998 Craig A. LaBarge

    You might also like