Active Products - Transceivers

LP-OSFPLRM01D
LC duplex 10GBASE-LRM 9.95 to 10.3 Gbps OM1 Multimode Fiber SFP+ 1310nm
MSA Transceiver up to 220 m.
LPOSFPLRM01D _SS_ENB01W

Features

Cost effective

Supports 9.95 to 10.3 Gbps

bit rates.

Transmission distance up
to 220m (OM1 fiber).

Hot Pluggable
SFP+ footprint.
1310nm FP transmitter,
PIN photo-detector.

Digital Status monitoring

Interface.

Duplex LC connector.

RoHS compliant and

Lead Free.

Metal enclosure for lower LP-OSFPLRM01D

EMI. LC duplex 10GBASE-LRM 9.95 to 10.3 Gbps OM1
Single 3.3V power supply. Multimode Fiber SFP+ 1310nm MSA Transceiver
Power dissipation < 1W
up to 220 m.
typical.
The LP-OSFPLRM01D is compatible with the Small Form Factor Pluggable
Operating case
Multi-Sourcing Agreement (MSA). The SFP+ LRM is an optical transceiver
temperature: 0 to 70ºC.
module for transmission at 1310nm over legacy multimode fiber.
Compliant with FC-PI-4
800-Mx-SN-I, SFF-8431, Supporting 10GBASE-LRM Ethernet standard, it is ideally suited for 10G data
SFF-8432 and SFF-8472. communications. The very low power consumption and its excellent EMI
performance allows for a system design with high port density.

Applications The LP-OSFPLRM01D is designed for use with Cisco network equipment and
is equivalent to Cisco part number SFP-10G-LRM.

The LP-OSFPLRM01D is The small form factor integrates a 1310nm Fabry-Perot (FP) laser in an LC
designed for use with Cisco package and a linear multimode PIN receiver. The module is lead free, RoHS
network equipment and compliant and is designed and tested in accordance with industry safety
is equivalent to Cisco part
standards.
number SFP-10G-LRM.

10GBASE-LRM 10G Gigabit The LP-OSFPLRM01D SFP+ transceiver is a linear-interface transceiver that
Ethernet. enables, in conjunction with an Electronic Dispersion Compensation (EDC)
on the host board, an IEEE802.3aq 10GBASE-LRM compliant link. The host
Legacy FDDI multimode
board EDC provides correction for the severe modal dispersion that may occur
links.
during propagation through multimode fiber links, including legacy installed
Switch to Switch interface. FDDI multimode fiber (see IEEE802.3aq for detailed information regarding
fiber coverage).
Switched backplane
applications.

Router/Server interface.

Other optical transmission

systems.
www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

A Compatibility List
• Catalyst 3850 Series - 3850-24F-E • ME 4900 Series Ethernet Switch - ME-4924-10GE
• Catalyst 3850 Series - 3850-48P-E • Catalyst 6500 Series - WS-X6708-10G-3CXL
• Catalyst 3850 Series - 3850-24P-E • Catalyst 6500 Series - WS-X6708-10G-3C
• Catalyst 3850 Series - 3850-48T-E • Catalyst 4900 Series Switch - WS-X4908-10GE
• Catalyst 3850 Series - 3850-24T-E • Catalyst 4900 Series Switch - WS-X4904-10GE
• Catalyst 3850 Series - 3850-48F-S • Catalyst 4900 Series Switch - WS-C4928-10GE
• Catalyst 3850 Series - 3850-48P-S • Catalyst 4900 Series Switch - WS-C4948-10GE
• Catalyst 3850 Series - 3850-24P-S • Catalyst 4500 Series Switch - WS-X4606-X2-E
• Catalyst 3850 Series - 3850-48T-S • Catalyst 3560-E Series - WS-C3560E-12SD
• Catalyst 3850 Series - 3850-24T-S • Catalyst 3100 Series Blade Switch- WS-CBS-3130X-S
• Catalyst 3850 Series - 3850-48F-L • Catalyst 3100 Series Blade Switch - WS-CBS-3120X-S
• Catalyst 3850 Series - 3850-48P-L • Catalyst 6500 Series - VS-S720-10G-3CXL
• Catalyst 3850 Series - 3850-24P-L • Catalyst 6500 Series - VS-S720-10G-3C
• Catalyst 3850 Series - 3850-48T-L • Catalyst 4500 Series Switch - WS-X45-SUP6-E
• Catalyst 3850 Series - 3850-24T-L • Catalyst 4500 Series Switch - WS-X4516-10GE
• Wide Area Virtualization Engine - WAVE-694 • Catalyst 4500 Series Switch - WS-X4013+10GE
• Wide Area Virtualization Engine - WAVE-594 • Catalyst 3750-E Series - WS-C3750E-48PDF
• 500 Series Stackable Managed Switch - SG500X-52P • Catalyst 3750-E Series - WS-C3750E-48PD
• 500 Series Stackable Managed Switch - SG500X-52 • Catalyst 3750-E Series - WS-C3750E-48TD
• 500 Series Stackable Managed Switch - SG500X-48P • Catalyst 3750-E Series - WS-C3750E-24PD
• 500 Series Stackable Managed Switch - SG500X-48 • Catalyst 3750-E Series - WS-C3750E-24TD
• 500 Series Stackable Managed Switch - SG500X-24P • Catalyst 3560-E Series - WS-C3560E-12D
• 500 Series Stackable Managed Switch - SG500X-24 • Catalyst 3560-E Series - WS-C3560E-48PDF
• Catalyst 6500 Series - WS-X6908-10G-2TXL • Catalyst 3560-E Series - WS-C3560E-48PD
• Catalyst 6500 Series - WS-X6908-10G-2T • Catalyst 3560-E Series - WS-C3560E-48TD
• Catalyst 6500 Series - WS-X6816-10G-2TXL • Catalyst 3560-E Series - WS-C3560E-24PD
• Catalyst 6500 Series - WS-X6816-10G-2T • Catalyst 3560-E Series - WS-C3560E-24TD
• Catalyst 6500 Series - WS-X6716-10G-3CXL • Nexus 7000 Series - N7K-F248XP-32E
• Catalyst 6500 Series - WS-X6716-10G-3C • OmniSwitch 6900 Series - OS-HNI-U6 Expansion Module
• Nexus 7000 Series - N7K-M132XP-12L • OmniSwitch 6900 Series - OS-XNI-U4 Expansion Module
• Nexus 7000 Series - N7K-M132XP-12 • OmniSwitch 6900 Series - OS-XNI-U12 Expansion Module
• Nexus 7000 Series - N7K-F248XP-25 • OmniSwitch 6900 Series - OS6900-T40
• Catalyst 4500 Series Switch - WS-X45-SUP7L-E • OmniSwitch 6900 Series - OS6900-X40
• Catalyst 6500 Series - VS-S2T-10G-XL • OmniSwitch 6900 Series - OS6900-T20
• Catalyst 6500 Series - VS-S2T-10G • OmniSwitch 6900 Series - OS6900-X20
• Catalyst 3750-X Series - WS-C3750X-24S • Nexus 2000 Series - N2K-C2248TP-E-1GE
• Catalyst 3750-X Series - WS-C3750X-12S • Catalyst 6500 VS-720-10G-3CXL
• ME 3800X - ME-3800X-24FS-M (SFP+ ports) • Catalyst 6500 VS-720-10G-3C
• Nexus 7000 Series - N7K-F132XP-15 • Catalyst 4500-X Series WS-C4500-X-F-16SFP+
• Catalyst 2360 Series - 2360-48TD-S • Catalyst 4500X Series WS-C4500-X-24X-ES
• Catalyst 4900 Series Switch - WS-C4948E • Catalyst 4500X Series WS-C4500X-16SFP+
• Catalyst 4500 Series Switch - WS-X45-SUP7-E • Catalyst 4500X Series WS-C4500-X-32SFP+
• Catalyst 4500 Series Switch - WS-X4712-SFP+E • Catalyst 4500 Series WS-X45-SUP8-E
• Catalyst 3750-X Series - WS-C3750X-48PF • Catalyst 3850 Series 3850-NM-10G
• Catalyst 3750-X Series - WS-C3750X-48P • Catalyst C2960-XR Series WS-C2960XR-24TS-LL
• Catalyst 3750-X Series - WS-C3750X-24P • Catalyst C2960-XR Series WS-C2960XR-48FPD-I
• Catalyst 3750-X Series - WS-C3750X-48T • Catalyst C2960-XR Series WS-C2960XR-48LPD-I
• Catalyst 3750-X Series - WS-C3750X-24T • Catalyst C2960-XR Series WS-C2960XR-24PD-I
• Catalyst 3560-X Series - WS-C3560X-48PF • Catalyst C2960-XR Series WS-C2960XR-48TD-I
• Catalyst 3560-X Series - WS-C3560X-48P • Catalyst C2960-XR Series WS-C2960XR-24TD-I
• Catalyst 3560-X Series - WS-C3560X-24P • Catalyst C2960-XR Series WS-C2960XR-24FPS-I
• Catalyst 3560-X Series - WS-C3560X-48T • Catalyst C2960-XR Series WS-C2960XR-48LPS-I
• Catalyst 3560-X Series - WS-C3560X-24T • Catalyst C2960-XR Series WS-C2960XR-24PS-I
• Catalyst 2960-S Series - WS-C2960S-24TD-L • Catalyst C2960-XR Series WS-C2960XR-48TS-I
• Catalyst 2960-S Series - WS-C2960S-48TD-L • Catalyst C2960-XR Series WS-C2960XR-24TS-I
• Catalyst 2960-S Series - WS-C2960S-24PD-L • Catalyst C2960-X Series WS-C2960-X-48FPD-L
• Catalyst 2960-S Series - WS-C2960S-48LPD-L • Catalyst C2960-X Series WS-C2960-X-48LPD-L
• Catalyst 2960-S Series - WS-C2960S-48FPD-L • Catalyst C2960-X Series WS-C2960-X-48TD-L
• Catalyst 2960-S Series - WS-C2960S-24TS-L • Catalyst C2960-X Series WS-C2960-X-24PD-L
• ME 3600X - ME-3600X-24TS-M (SFP+ Ports) • Catalyst C2960-X Series WS-C2960-X-24TD-L
• ME 3600X - ME-3600X-24FS-M (client ports) • Catalyst C2960-X Series WS-C2960-X-48FPS-L
• Catalyst 4500 Series Switch - WS-X45-SUP6L-E • Catalyst C2960-X Series WS-C2960-X-24TS-L

2 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

A Compatibility List
• Catalyst C2960-X Series WS-C2960-X-24PS-L
• Catalyst C2960-X Series WS-C2960-48TS-LL
• Nexus 7000 Series - N7K-M224XP-23L
• Nexus 7000 Series - N7K-F248XP-25E
• Catalyst 6500 Series WS-X6904-40G-2TXL
• Catalyst 6500 Series WS-X6904-40G-2T
• Catalyst 4900 Series Switch - WS-C4900M
• Catalyst 2960-X Series - WS-C2960X-18TS-LL
• Catalyst 2960-X Series - WS-C2960X-48FPD-L
• Catalyst 2960-X Series - WS-C2960X-48TD-L
• Cisco Catalyst 3650-48P Layer 3 Switch - WS-C3650-48PD-S
• Cisco Catalyst 3650 Series Switch - WS-C3650-48FD-L
• Cisco Catalyst WS-C3650-24TS
• Cisco Catalyst 3650 Series...
• Cisco Catalyst WS-C3650-24PS
• Cisco Catalyst WS-C3850-12S
NOTE: Cisco and the Cisco logo are trademarks or registered trademarks of Cisco Systems, Inc. This product is not certified or endorsed
by Cisco Systems.

B Información del EEPROM:

Figure 1. Block Diagram of SFP+ LRM Module on Host Board with with EDC
Unlike the XFP MSA transceiver requirements, the SFP+ transceiver does not contain internal retiming circuitry, and thus
some of the Transmitter Optical Characteristics stated in this data sheet require that the Host Board is compliant to the
SFP+ MSA specifications. See Chapter 3 in Reference [1] for further details.

C Absolute maximum ratings

These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum
Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended
Operating Conditions.

Parameter Symbol Min Max Unit

Power Supply Voltage VccT 0 +3.6 V

Storage Temperature Tc -40 +85 ºC

Opetating Case Temperature Tc 0 +70 ºC

Relative Humidity RH 5 95 %

3 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

D Recommended operating environment

Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless
otherwise noted.

Parameter Symbol Min Typical Max Unit

Power Supply Voltage Vcc 3.135 3.300 3.465 V
Storage Temperature Tc 0 25 70 ºC

E Low Speed Characteristics

Parameter Symbol Min Typical Max Unit

Power Consumption 0.8 1 W
VOL 0 0.4 V
TX_Fault, RX_LOS
VOH Host_Vcc-0.5 Host_Vcc+0.3 V
VIL -0.3 0.8 V
TX_DIS
VIH 2.0 VCCT+0.3 V
VIL -0.3 0.8 V
RS0, RS1
VIH 2.0 VCCT+0.3 V

F Electrical Characteristics

Parameter Conditions Symbol Min Typical Max Unit

Nominal Data Rate VID 10.3125 Gbps

Supply Voltage VCC 3.14 3.46 V

Supply Current ICC 200 300 mA

Power Dissipation P 1 W

Transmitter

Input differential impedance 2 Rin 100

Single ended data input swing 3 Vin, pp 90 350

Transmit Disable Voltage 4 VD 2 Vcc

Transmit Enable Voltage VEN Vee Vee+ 0.8 V

Receiver

Termination Mismatch at 1 MHz ∆ZM -0.3 %

Single Ended Output Voltage Tolerance V

Output AC Common Voltage 30 mVrms

Output Rise and Fall time (20% to 80%) 5 Tr, Tf Ps

Relative Noise LRM Links with crosstalk 6 dRNx dB/HZ

Difference Waveform Distorsion Penalty 7 dWDP per SFF-8431 dB

Differential Voltage Modulation Amplitude VMA 180 600 mV

LOS Fault 8 VLOS fault 2 VCCHOST V

LOS Normal 8 VLOS norm Vee Vee+0.8 V

Power Supply Noise Tolerance 9 VccT/VccR per SFF-8431 mVpp

4 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

Notes:
1. Non-condensing.
2. Connected directly to TX data input pins. C coupling from pins into laser driver IC.
3. Per SFF-8431 Rev 3.0
4. Into 100 ohms differential termination.
5. Measured with Module Compliance Test Board and OMA test pattern.
6. Crosstalk source rise/fall time (20%-80%) is 35 ps.
7. Defined with reference receiver with 14 T/2 spaced FFE taps and 5 T spaced DFE taps.
8. LOS is an open collector output. Should be pulled up with 4.7k - 10kΩ on the host board.
Normal operations is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V.
9. As described in Section 2.8.1, SFF-8431 Rev 3.0.

G General Specifications

Parameter Symbol Min Typical Max Unit Notes

Bit Rate BR 10.3125 Gb/sec 1
Bit Error Ratio BER 10-12 2
Maximum Supported Distances
Fiber Type 1310nm OFL Bandwidth
"FDDI" 160MHz/km 220
62.5μm Lmax m 3
OM1 200MHz/km 220
400MHz/km 100
50μm OM2 500MHz/km Lmax 220 m 3
OM3 2000MHz/km 220

Notes:
1. 10GBASE-LRM
2. Tested with a 231 – 1 PRBS
3. Operating range as defined by IEEE standards. Longer reach possible depending upon link implementation.

H Optical Characteristics

Parameter Symbol Min. Typical Max Unit Notes

Transmitter
Center Wavelength λt 1260 1355 nm
λrms@1260nm - 2.4
- 2
RMS specatral width λrms@1260-1300nm - 2.4 nm
λrms@1300nm-1355 - 4
Average Optical Power Pavg -6.5 - 0.5 dBm 1
Extinction Ratio ER 3.5 - - dB
Optical Modulation Amplitude (OMA) POMA -4.5 +1.5 dBm
Peak Launch Power PMAX 3 dBm
Transmitter Waveform
TWDP 4.7 dB 3
Dispersion Penalty
Average Launch power of OFF
POFF -30 dBm
transmitter
Uncorrelated Jitter (rms) (rms) 0.033 UI
<5µm 30
Encircled Flux %
<11µm 81

5 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

H Optical Characteristics

Parámetro Símbolo Mínimo Típico Máximo Unidad Notas

Transmitter Reflectance -12 dB
Optical Return Loss Tolerance 20 dB
Relative Intensity Noise Rin -128 Db/Hz
Receiver
Procyrsir -6.5 dBm
Comprehensive Stressed Reciver
Symmetrical -6 dBm
Sensivity (OMA) @10.3125Gb/s
Postcursor -6.5 dBm
LOS Assert LosA -30 dBm
LOS De-Assert LosD -11 dBm
Overload PMAX +1.5 dBm
Receiver Reflectance - -12 dB
LOS Hysteresis 0.5 dB
Notes:
1. Average power figures are informative only, per IEEE802.3aq
2. Maximum RMS spectral width as specified by Figure 3
3. Optical Eye Mask requires the host board to be SFF-8431 compliant. Optical eye mask per IEEE802.3aq.
4. TWDP figure requires the host board to be SFF-8431compliant. TWDP is calculated using the Matlab code provided
in clause 68.6.6.2 of IEEE802.3aq
5. Receiver overload specified in OMA and under the worst comprehensive stressed condition.
6. Conditions of stressed receiver tests per IEEE802.3aq. CSRS testing requires the host board to be SFF-8431 compliant.

I Digital Diagnostic Functions

The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless otherwise
specified. It is compliant to SFF8472 Rev9.2 with internal calibration mode. For external calibration mode please contact
our sales stuff.

Parameter Symbol Min Max Unit Notes

Accuracy
Transceiver Temperature DMI_Temp -3 +3 degC Over operating temp
TX Output optical power DMI_TX -3 +3 dBm
RX Input optical power DMI_RX -3 +3 dBm -3dBm to -12dBm range
Transceiver Supply voltage DMI_VCC -0.08 +0.08 V Full operating range
Bias current monitor DMI_Ibias -10% 10% mA
Dynamic Range Accuracy
Tranceiver Temperature DMI_Temp -5 70 degC
TX Output optical power DMI_TX -9 -1 dBm
RX Input optical power DMI_RX -18 0 dBm
Transceiver Supply voltage DMI_VCC 3.0 3.6 V
Bias current monitor DMI_Ibias 0 70 mA

6 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

J Pin Assignment

Figure 2: Interface to Host PCB

Figure 3. Module Contact Assignment

7 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

K Pin Descriptions

Pin Signal Name I/O Typ. Functional Description

1 VeeT[1] Transmitter Ground

Transmitter Fault Indication, Logic high, open collector Compatible ,

2 TX_FAULT[2]
4.7K to 10K Ohm pull up to VDDT on host

3 TX_DISABLE[3] Transmitter Disable – Module disable on high or open

4 SDA[2] I/O 2-wire Serial Interface Data Line

5 SCL[2] Input 2-wire Serial Interface Clock Line

6 MOD_ABS[4] Output Module Absent. Grounded within the module

7 RSO[5] Input Rate Select 0

8 RX_LOS[2] Loss of Signal indication. Logic 0 indicates normal operation

9 RS1[5][1] Rate select 1

10 VeeR[1] Receiver Ground

11 VeeR[1] Receiver Ground

12 RD- Output Inverse Received Data Out, AC coupled

13 RD+ Output Received Data Out, AC coupled

14 VeeR[1] Receiver Ground

15 VccR Input Receiver Power Supply

16 VccT Input Transmitter Power

17 VeeT[1] Transmitter Ground

18 TD+ Input Transmitter Data In, AC coupled

19 TD- Input Inverse Transmitter Data In, AC coupled

20 VeeT[1] Transmitter Ground

Notes:
[1] Module circuit ground is isolated from module chassis ground within the module.
[2] Should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.
[3] Tx_Disable is an input contact with a 4.7 kΩ to 10 kΩ pullup to VccT inside the module.
[4] Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull this contact up to Vcc_Host with a
resistor in the range 4.7 kΩ to10 kΩ.Mod_ABS is asserted “High” when the SFP+ module is physically absent from a host
slot.
[5] RS0 and RS1 are module inputs and are pulled low to VeeT with > 30 kΩ resistors in the module.

8 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

Figure 4. Host Board Power Supply Filters Circuit

Figure 5. Host-Module Interface

9 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

Figure 6. Mechanical Specifications

L Regulatory Compliance

The SFP+ transceiver is designed to be Class I Laser safety compliant and is certified per the following standards:

Feature Agency Standard Certificate / Comments

CDRH 21 CFR 1040 and

Laser Safety FDA 1120292-000
Laser Notice No. 50

Procuct Safety UL UL and CUL EN60950-2:2007 E347511

Environmental
SGS RoHS Directive 2002/95/EC GZ1001008918/CHEM
protection

EN 55022:2006+A1:2007
EMC WALTEK WT10093759-D-E-E
EN 55024:1998+A1+A2:2003

10 www.lanpro.com
 Active Products - Transceivers - LP-OSFPLRM01D

References:

1. “Specifications for Enhanced Small Form Factor Pluggable Module SFP+”, SFF-8431, Rev 4.1, July 6, 2009.
2. “Improved Pluggable Formfactor”,SFF-8432, Rev 4.2,Apr 18,2007.
3. IEEE802.3aq.
4. “Diagnostic Monitoring Interface for Optical Transceivers” SFF-8472, Rev 10.3, Dec 1, 2007.

Important Notice:

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically
confirmed in writing by us before they become applicable to any particular order or contract. In accordance with the the
policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of ours.
Further details are available from any our sales representative.

M How to Order:

LP-OSFPLRM01D LC duplex 10GBASE-LRM 9.95 to 10.3 Gbps OM1 Multimode Fiber SFP+ 1310nm
MSA Transceiver up to 220 m.

LanPro is continuously improving its products and reserves the right to change
specifications and availability without prior notice.

11 www.lanpro.com