Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Betrework Worku PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 85

ADDIS ABABA UNIVERSITY

ADDIS ABABA INSTITUTE OF TECHNOLOGY


SCHOOL OF CHEMICAL AND BIO ENGINEERING

Formulation of Shoe Polish from Wax and Used Water SAchets

Betrework Worku

Advisor: Prof.Belay Woldeyes

A Thesis Submitted to
The School of Chemical and Bio-Engineering

A Partial Fulfillment of the Requirements for the Degree of Master of


Science (Process Engineering)

Addis Ababa University


Addis Ababa, Ethiopia
June, 2017
ADDIS ABABA UNIVERSITY
ADDIS ABABA INSTITUTE OF TECHNOLOGY
SCHOOL OF CHEMICAL AND BIOENGINEERING

This is to certify that the thesis is prepared by Betrework Worku, entitled:


Formulation of Shoe Polish from Wax and Used Water Sachets and submitted
in partial fulfillment of the requirements for the Degree of Master of Science in
Process Engineering complies with the regulations of the University and meets
the accepted standards with respect to originality and quality.

Signed by the Examining Committee:

Internal Examiner: Signature ____________ Date ______________

External Examiner: Signature ____________ Date ______________

Advisor: Prof. Belay Woldeyes Signature ____________ Date _____________

____________________________________
School or Center Chair Person
DECLARATION
I declare that this thesis for the M.Sc. Degree at Addis Ababa University, hereby submitted
by me, is my original work and has not previously been submitted for the degree at this or
any other university, and that all resources of materials used in this thesis have been duly
acknowledged.

Name: Betrework Worku

Signature: _________

Date of Submission: ___________

This thesis has been submitted for examination with my approval as University Advisor.

Name: Prof.Belay Woldeyes

Signature: _________

Date: _________
Declaration

I declare that this thesis for the M.Sc. Degree at Addis Ababa University, hereby submitted
by me, is my original work and has not previously been submitted for the degree at this or
any other university, and that all resources of materials used in this thesis have been duly
acknowledged.

Name: Betrework Worku


Signature: _________

Date of Submission: ___________

This thesis has been submitted for examination with my approval as University Advisor.
Name: Prof.Belay Woldeyes
Signature: _________
Date: _________

i
Acknowledgment
I would like to express my sincere gratitude to Prof. B. Woldeyes for his guidance and
assistance in this thesis. The technical discussions with Prof S. Woldeyes were always very
insightful, and I will always be indebted to him for all the knowledge he has shared with
me. His prompt responses and availability despite busy schedule were truly appreciated.
He always helped me in all the technical and non-technical issues during my period of
work. His encouragement and efforts are leading the project towards completion at a great
speed.
I would also like to thank Mr. T. Hennsa, and Mr. G. Mekoria for their help during my
experiments. It has been a pleasure working with them. I am grateful for the friendly
advices, technical assistances and encouragement that they have offered me throughout my
work.
I take this opportunity to thank my friends K. Melesa, Tamerat Yemher and Yeshak
G.Tatios,Kalkidan Ibraium Share for their assistance, help and support in my work of Shoe
Polish formulation.
A final word
I am aware more than ever before of how much I have learned from this study and will
continue to learn from my lecturers, respondents, other authors and readers involved in
this field of study. If you have a comment or suggestion for making this research thesis
work better, please email me at: betrework68@gmail.com.

ii
Abstract
The conversion of Used Water Sachets to Shoe Polish was investigated. Used water sachets
were pyrolyzed at various temperatures to obtain polyethylene (sachet) wax. Polyethylene
wax with good melting point, yield was produced between 100 - 200˚C, used to produce the
shoe polish. Three different formulated shoe polishes were prepared from polyethylene
wax and the properties of the three samples were compared with the standard polish
(Kiwi). The density, melting point, physical testing of shoe polish, and viscosity of the polish
formulated using different percentage of used polyethylene wax, compared favorably with
standard commercial polish.
The effects of temperature and pyrolysis time on the properties of polyethylene wax
produced from used water sachets were investigated. Used water sachets were pyrolysed
at temperatures between 100 -200 ℃ for 30-60 min.
The effect of temperature and pyrolysis time is significant on the yield and melting point of
sachet wax produced. The sachet wax obtained had the melting point of 76 ℃ while the
yield of sachet wax was 35.4 %.Waste sachets pyrolysed at 100 °C for 45 minutes produced
sachet wax from used water sachets with yield of 35.4 %, good melting point & viscosity.
Keywords: Used Water Sachets, Polyethylene Wax, Pyrolysis, Shoe Polish.

iii
Table of Contents
Declaration ................................................................................................ Error! Bookmark not defined.
Acknowledgment .................................................................................................................................................. ii
Abstract ................................................................................................................................................................... iii
Table of Content…………………………………………………………………………………………………………….iv
List of Figures………………………………………………………………………………………………………………..ix
List of
Tables…………………………………………………………………………………………………………………..ix
List of Acronyms/Abbreviations…………………………………………………………………………………..…xi
Chapter One........................................................................................................................................................... 1
1. Introduction ..................................................................................................................................................... 1
1.1. Background .................................................................................................................................................... 1
1.2. Problem of Statement ................................................................................................................................ 2
1.3. Goal and Objectives..................................................................................................................................... 3
1.3.1. General Objective .................................................................................................................................. 3
1.3.2. The specific objectives of this research are:- ............................................................................. 3
1.4. The Significance and its applications ................................................................................................... 3
Chapter Two.......................................................................................................................................................... 4
2. Literature Review ......................................................................................................................................... 4
2.1. Research Problem Analysis ..................................................................................................................... 4
2.2. Introduction about Shoe polish.............................................................................................................. 6
2.2.1. Composition and Toxicology ........................................................................................................... 7
2.2.2. Non –toxic Shoe polish ...................................................................................................................... 7
2.3 Motivations for the Study .......................................................................................................................... 8
2.4 Theoretical Basis of Plastic Wastes……………………………….……….……..……………………………9
2.4.1. Polyethylene (PE) ................................................................................................................................10
2.4.1.1. Low Density Polyethylene…………………………………………………………………………..11
2.4.1.2. High Density Polyethylene………………………………………….………………………....…….11
2.4.2. Plastic Waste (used water sachets) Disposal as a Global Problem……………..……........12
2.4.2.1. Alternative Technology as multiple solution pakages……………...…….…..…….…...12
2.4.3. Properties of Polyethylene………………………..………………………………….….…...……………12
2.5. Plastic wastes recycling techniques…………………………………………………………….…………..14
2.5.1. Mechanical recycling techniques ....................................................................................................14
2.5.2. Chemical or feedstock recycling techniques…………………………………………………………15

iv
2.5.2.1. Chemical de polymerization……………………………………………………………………....14
2.5.2.2. Thermal Cracking (Pyrolysis)……………………………………………………………………..15
2.5.2.3. Catalytic Conversion…………………………..……………………………………………………...15
2.5.2.4. Gasification………………………………………………………………………………………………..16
2.5.2.5. Cove even chemical feedstock recycling……………………………………………………....16
2.6. Pyrolysis of plastics ..................................................................................................................................17
2.6.1. Pyrolytic process parameters condition....................................................................................17
2.6.1.1. Temperature……………………………………………………...…………………………………….17
2.6.1.2. Type of reactors……………………………………………………………………………………….17
2.6.1.3. Residence time…………………………………………………………………………………………18
2.7. Natural Wax ..................................................................................................................................................19
2.7.1. Plant and animal waxes .....................................................................................................................19
2.7.1.1. Animal Waxes…………………………………………………..……………………………………….18
2.7.1.2. Plant Waxes….................................................................................................................................19
2.7.2. Bee Wax ....................................................................................................................................................20
2.7.2.1. Bee wax at present…......................................................................................................................19
2.8. Rationale for Research Methodology ..................................................................................................20
Chapter Three ....................................................................................................................................................23
3. Materials and Methods .............................................................................................................................23
3.1. Materials ........................................................................................ Error! Bookmark not defined.
3.2. Methods.....................................................................................................................................................23
3.2.1. Bee wax Melting……………………………………………….…………….………………………...…….22
3.2.2. Pyrolytic reactor process………………………………………………………………..………………22
3.2.3. Pyrolysis of used water sachets plastics……………….………………………….…….….……..22
3.2.4.Preparation of shoe polish from Bee wax and used water sachet ................................24
3.2.4.1.Preparation of shoe polish ................................... Error! Bookmark not defined.
3.2.4.2. Shoe polish formulations & their mixing…………………....…………………………..23
3.2.5. Proximate analysis .............................................................. Error! Bookmark not defined.
3.2.5.1. Ash content determination………….…………………………………………………………24
3.2.5.2. Volatile matter content determination…………………………………………………....24
3.2.5.3. Fixed carbon content determination…………………….………………………………...24
3.2.6. Characterization of Polyethylene wax ......................................................................................25
3.2.6.1. Standard Test Method for Melting Point of Polyethylene Wax .........................25
3.2.6.2. Density determination of Polyethylene wax by Measuring Cylinder ..............26

v
3.2.7. Characterization of shoe polish ..................................................................................................26
3.2.7.1. Viscosity Determination by Rotary Viscometer Method .........................................26
3.3. Evaluation of the Performance of Shoe Polish & Compared with Commercial Product
....................................................................................................................................................................................27
3.3.1. Luster/Gloss………………………………………………………………..…………………………………..26
3.3.2. Rub resistance…………………………………………………….………..………………………………….26
3.3.3. Fading resistance…………………………………………….…………………………………………….....26
3.3.4. Dust absorption resistance……………………………………………………….…...………………….26
3.3.5. Wrinkle/crease resistance…………………………………………………….………………………….26
3.4. Optimization of process Parameters.................................................................................................27
3.5. Performing Techno-Economic Feasibility Study ...........................................................................28
Chapter Four .......................................................................................................................................................29
4. RESULT AND DISCUSION..........................................................................................................................29
4.1. Formulated polyethylene wax from used water Sachets ............................................................29
4.1.1 Design Expert Output ( yield ) ........................................................................................................29
4.1.1.1. Response output of yield………………………………………...………………………………….28
4.1.1.2. Appropriate residual plots & comment on the model adequacy……………...……32
4.2. Characterization Results..........................................................................................................................33
4.2.1. Proximate Analysis of a Raw Material ........................................................................................33
4.2.2. Melting point………………………………………..…………………………..………………………………34
4.2.2.1. Response output of melting point……………………………………………………………….36
4.2.2.2. Appropriate residual plots & comment on the model adequacy………….……...…40
4.3. Thermo physical Properties of Shoe Polish......................................................................................38
4.3.1. Melting Point of shoe polish ..........................................................................................................38
4.3.2. Density of Shoe Polish......................................................................................................................39
4.3.3. Viscosity of Shoe Polish at Different Temperatures.............................................................40
4.3.3.1. Appropriate residual plots & comment on the model adequacy………….………47
4.4. Performance of Shoe polish & Compared with Commercial Product….………………...........43
Chapter Five ........................................................................................................................................................44
5. MATERIAL AND ENERGY BALANCE ....................................................................................................44
5.1. Heat and Mass Balance Analogies ........................................................................................................44
5.1.1. Energy and Mass Input and Output in a Process ....................................................................45
5.1.2. Mass Balance within the Process ..................................................................................................46
5.2. Material Balance .........................................................................................................................................46
5.3. Energy Balance Calculation ....................................................................................................................48

vi
5.3.1. Thermodynamic properties for the energy balance .............................................................49
5.4. Equipment Design and Selection ..........................................................................................................49
5.4.1. Reactor Volume ...................................................................................................................................50
5.4.2. Equipment specifications ................................................................................................................50
Chapter Six ...........................................................................................................................................................51
6. Economical Feasibility Study ................................................................................................................51
6.1. Plant Location & Site Location...............................................................................................................51
6.2. Market Study &Plant Capacity ...............................................................................................................52
6.2.1. Past Supply and Present Demand .................................................................................................52
6.2.2. Projected Demand ...............................................................................................................................54
6.3. Plant Capacity and Production Program ...........................................................................................54
6.3.1. Plant Capacity........................................................................................................................................54
6.4. Economical Estimation .............................................................................................................................55
6.4.1. Estimated Capital Costs For Shoe polish Production .............................................................55
6.4.1.1. Estimation of total capital investment………………………………………………………….64
6.4.2. Estimation of Total Product Cost ...................................................................................................57
6.4.2.1. Estimation of Manufacturing Cost…………………………….………………………………….65
6.4.2.2. Estimation of General Expenses Cost…………………………………………………………...66
6.4.3 .Production Program ............................................................................................................................58
6.4.4. Financial Evaluation ............................................................................................................................59
6.4.4.1. Profitability........................................................................................................................................67
6.4.4.2. Break Even analysis……………………….……………………………………………………….……67
6.4.4.3. Payback Period…………………………………………………………………………………………....67
6.4.4.4. Internal Rate of Return….............................................................................................................67
6.4.4.5. Net Present Value….......................................................................................................................68
6.5. Economic & Social Benefits.....................................................................................................................60
Chapter Seven ....................................................................................................................................................61
7. Conclusion & Recommendation ..........................................................................................................61
References ...........................................................................................................................................................62
Appendices ..........................................................................................................................................................65
Financial Analysis Supporting Tables .........................................................................................................65
Appendix I: Income Statement (in 000 Birr)............................................................................................65
Appendix II: Cash Flow for Financial Management ...............................................................................66
Appendix I I I: Discounted Cash Flow (in 000 Birr) ..............................................................................67
Appendix IV: Pictures of Plastic disposal and Laboratory Equipments ........................................68
vii
List of Figures
Figure Title Page No
Figure 2.1Consumer waste plastics form a complex mixture………………………….………………...8
Figure 2.2Schematic representation of research methodology………..………………….…………11
Figure 2.3Optimization stages…………………………………………………………….………………………....21
Figure 4.1Interaction graph of yield…………….……………………………………………...…………………29
Figure 4.2One Factor Plot of Yield vs. Temperature………………….…………………………………….30
Figure 4.3One Factor Plot of Yield vs. Time………….…………………………………………………………31
Figure 4.4Normal Plots of Residuals……………….……………………………………………………………..32
Figure 4.5Plot of Residual vs. Predicted…….…………………………………………………………………...33
Figure 4.6Plot of Residuals vs. Temperature……….………………………………………………………….34
Figure 4.7Plot of Residuals Vs Time ………….…………………………………………………………………..34
Figure 4.8Proximate analysis results………….………………………………………………………………….35
Figure 4.9Interaction graph of melting point…….…………………………………………...……………….37
Figure 4.10One Factor Plot of melting point vs. Temperature…………………………………………38
Figure 4.11One Factor Plot of melting point vs. Time…………..………………………………………….39
Figure 4.12Normal Plots of Residuals………………………….…………………………………………………40
Figure 4.13Plot of Residual vs. Predicted …………………………….………………………………………...40
Figure 4.14Plots of Residuals vs. Temperature……………………………….………………….…………..41
Figure 4.15Plots of Residuals vs. Temperature……………….……………………………………….……..41
Figure 4.16Plots of Residuals vs. Time……………….…………………………………………………….…….42
Figure 4.17Melting point of formulated & controlled shoe polish….………………………………...43
Figure 4.18 Density of formulated and controlled shoe polish………………………………………...44
Figure 4.19Model graph one factor plot of viscosity vs. Temperature……….……………………..45
Figure 4.20Model graph one factor plot of viscosity vs. formulated Shoe polish………….…...46
Figure 4.21Normal Plot of Residuals of viscosity……….…………………………………………………...47
Figure 4.22Plot of Residuals vs. Predicted of viscosity……….…………………………………………...48
Figure 4.23Plots of Residuals vs. Temperature of viscosity…………………….……………………….49
Figure 4.24Plots of Residuals vs. Formulated shoe polish of viscosity……………………………..50
Figure 5.1Modeling the energy and mass calculations………………………………………….…………53

viii
List of Tables
Table Title Page No
Table 1.1 Ethiopia's imported shoe polishes…………………………………………………………………....2
Table 3.1 Shoe Polish Formulations……………………………………………………………………………….23
Table 4.1 Reaction temperature, time and Yield of sachet wax…………………….……………….…28
Table 4.2 Analysis of variance table [Partial sum of squares]………………………………………….28
Table 4.3 Constraints and optimaization………………………………………………………………………..31
Table.4.4 Proximate Analysis of used water sachet ……………………………………………….……….35
Table 4.5 Melting point result at different temperature and time....................................................36
Table 4.6 Properties of sachet Wax Produced from Waste Water Sachets……………………….36
Table 4.7 Analysis of variance table [Partial sum of squares]of melting point………………….36
Table 4.8 Melting Point of Shoe Polishes………………………………………………………………………..42
Table 4.9 Density of shoe polish…………………………………………………………………………………….44
Table 4.10 Viscosity of polishes at different temperature………………...……………….…………….45
Table 4.1 Physical tested of shoe polish…………...…………………………………………………………….51
Table 5.1 an analogy of heat and mass transfer………………………………………………………….......52
Table 5.2 Energy balance on Carbolite reactor……………………………………………………….………57
Table 5.3 Equipment specification and sizing…………………………………………………………………58
Table 6.1 Past supply data of shoe polish……………………………………………………………………….61
Table 6.2 Projected demand for polish (TONS)……………………………………………………………....62
Table 6.3 Purchased Equipment cost……………………………………………………………………………..63
Table.6.4. Estimation of FCI and TCI………………………………………………………………………………64
Table 6.5 Production Program………………………………………………………………………………………67

ix
List of Acronyms/Abbreviations
Acronyms/abbreviation Full expression
MSW Municipal solid waste
FCI Fixed Capital Investment
TCI Total Capital Investment
WC Working Capital
IRR Internal Rate of Return
MC Moisture Content
VC Volatile Matter
AC Ash Content
FC Fixed Carbon
BEP Break Even Point
CSBR Conical spouted bed reactor
HDPE High Density Polyethylene
LDPE Low Density Polyethylene
PVE Polyvinyl Chloride
PS Polystyrene
PP Polypropylene

x
xi
12
Chapter One
1. Introduction
1.1. Background
The emergence of polish technology in engineering is apparent offshoot complexities
resulting from the indication of substances that produce desire goals and provides a
protective coating for the surface of the materials, changing in to a dry adherent film.
Therefore, shoe polish is a substance usually wax based, which applied to a sequence wax
based, which applied to a sequence protects, makes it smooth and shiny. It has been,
discovered that shoe polish industries in Ethiopia are at minimum even though the polish
industry is economically very important due to its widespread usage. The manufacture of
surface coaling materials of which shoe polishes a part has been estimated with more than
10,000 million yearly. This is in essence means that its usage is wide spread and in terms of
employment, gives lot of opportunities.

The demand for polishes largely met through import. Ethiopia imports a variety of polishes
and creams used in different applications. The data source for import statistics i.e.
Ethiopian Revenue and Customs Authority classifies import of polishes and creams under
the following headings.
34051000 – Polishes, creams and similar preparations for foot wear or leather;
34052000 – Polishes, creams and similar preparations for maintenance of wood work; and
34053000 –polishes, creams and similar preparations for coachwork
Among the above three types of polishes and creams imported during the period 2000-
2001 , only the first two types , which are intended for use in footwear and wood are
considered in the analysis of past supply and present demand . The quantity and value of
the two types of shoe polishes and creams imported in the past 12 years covering the
period 2000-2011 is presented in Table 1.1.

1
Table 1.1 Ethiopia's imported shoe polishes
Year Amount of Shoe Polish [Ton] Cost in ( 000 ) Birr
2000 382.2 9776
2001 478.8 12,959
2002 393.7 10,825
2003 345 8,642
2004 473.4 12,495
2005 586.2 15,312
2006 587.5 19,159
2007 672.3 20,441
2008 661.1 23,482
2009 495 25,095
2010 568 37,991
2011 442.1 33,313
Source: - Ethiopian Revenues and Customs Authority.
The objective of this thesis research was to convert used water sachets to useful product
such as wax and to formulate solid Shoe Polish. The properties of the shoe polish produced
were, studied and compared with standard commercial shoe polishes.
1.2. Problem of Statement
All over big cities in Ethiopia and even in the rural communities, it is a common sight that
polyethylene films, shopping bags, plastics, water sachets littering and polluting the
environment.
Plastic is a light, durable synthetic material that has found a lot of use in the modern world.
The plastic material comes in various types depending on its application. Polypropylene
(PP) is the most widely used plastic type in the world today followed by Polyethylene
(PE).There are many other forms of other plastics whose applications depend on intended
purpose. Large production and use of plastics for various applications has resulted in huge
volumes of plastic wastes. This has lead to proliferation in the environment as a result of
accumulation and fragmentation of plastic waste. Most of this waste is non-degradable and
highly resistant to light, acids and other tough conditions. Some of the negative impacts
resulting from poor waste plastic disposal include; choking and starving marine and
wildlife, littering the surrounding environment and blocking drainage systems and water
bodies. Burning of plastics in open fires, landfills or by use of municipal solid wastes (MSW)
incinerators releases toxic gas emissions. These gases include the persistent organic

2
pollutants (POP’s) such as dioxins. Studies have proved that this gas are carcinogenic and
have endocrine disrupting effects in a wide range of biota. Other emissions include the
Green House Gases (GHG’s) that cause global warming.
It has been, discover that shoe polish industries in Ethiopia are at minimum even though
the shoe polish industry is economically very important due to its widespread usage.
It is, therefore necessary to convert these huge used water sachets in to useful raw
material. This material called Polyethylene (Sachet) wax formulated from used water
sachets was very important to produce shoe polish.
1.3. Goal and Objectives
1.3.1. General Objective
To formulate shoe polish from wax and used water sachets
1.3.2. The specific objectives of this research are:-
 To formulate polyethylene wax from used water sachets
 To Prepare shoe polish from bee wax & polyethylene wax
 To characterize the product
 To determine the optimum parameters (temperature, time, mixing ratio).
 To evaluate the performances of shoe polish and compare with commercial product
 To optimize the process parameters using experimental design software.

1.4. The Significance and its applications


Considering the fact that there are few or practically no functional shoe polish industry in
the country and the imported shoe polish , most times do not meet up with the local
weather conditions due to this ,research thesis was helped a solution to these problems,
and at the same time offer local alternatives to these imported products. Importantly,
exploiting the benefit offered by this research work was helped in improved the qualities of
shoe polish produced. This was help in making the shoe polish industry a viable venture;
this product will be exported and there by serving as a foreign, exchange earner for the
country.
A waste-to-shoe polish process and technology is valorized as an alternative sustainable
energy source. This contributes significantly in solving the socioeconomic, health and
environmental problems linked to waste disposal in general and plastic waste management
in particular.

3
Chapter Two
2. Literature Review
2.1. Research Problem Analysis
Wastes are inevitable and can be found everywhere. They are the essentials derivatives of
every process. Wastes are therefore can be defined as any garbage, rubbish or other
discharged materials resulting from industrial , commercial domestic , mining and
agricultural activities. In a sense, wastes can be regarded as any material discarded as
having no consumer value to the person abandoning it. Wastes pollute the environment if
they are not properly disposed and managed. On the other hand if it is properly disposed
and managed will not constitute any environment problem and as such, pollution will
eradicated. This is because wastes are just (useful) materials in the wrong place. (Ahmadu,
2007). Thus wastes can simply be considered as nothing but unsorted scraps. Scraps are
useful raw materials that can be recycled in to new products. Thus , the enormous
problems caused by used and wrongly disposed polyethylene products ( used water
sachets ) can be reduced to barest minimum if properly sorted and recycled in to useful
products typical of shoe polish production.

Municipal waste plastic represents about 8% wt. of the municipal solid waste and it
generally consists of different kind of plastics. This waste is difficult to be treated or
recycled due to its complex nature and composition, structural deterioration of the
polymeric components and the contamination with various organic, inorganic and
biological residues.(Ademiluyi F. Oboho E, JULY 2013).
All over big cities in Ethiopia and even in the rural communities, it is a common sight that
polyethylene films, shopping bags, plastics, water sachets littering and polluting the
environment.

The increase of plastic waste and its harm in Ethiopia environment has attracted the
concern of the political and technological circles. These days, the waste polyethylene (often
called used water sachets) is known to cause blockage of drainage systems in our
townships and in rural commodities, since these waste films are non biodegradable this has
resulted in the flooding of our communities whenever it rains and subsequent destruction
of houses and farmlands.
Polyethylene is a macromolecular hydrocarbon that can be converted into useful products
such as oil and waxes but since the molecular chain of polyethylene is composed of -CH2-,
the freezing point of the diesel obtained is very high and the research octane number of

4
Gasoline is very low. Thus it is not a feasible way to convert polyethylene to oil. It is,
however a profitable way to convert polyethylene waste to polyethylene wax (Jixing et al.,
2003).

Several studies have been carried out to produce wax from waste. A study on the
conversion technology of waste polyethylene plastic (Used water sachet) to polyethylene
wax was carried out by Jixing et al., (2003). The effect of the reaction conditions including
pyrolysis temperature, pyrolysis time, and the content of the additive on the yield and
quality of the polyethylene wax such as melting point, density were discussed.

The polyethylene wax obtained has a melting point of 65-125°C, the yield of PE wax is over
30 %. Using used polyethylene water sachets of 97.72 % at 130-190℃, they obtained fuel
oil of 18.30 %, 76.14 % of wax and 3.28 % of gaseous products. This result showed that
more wax can be obtained at temperatures lower than 190℃ , but the property of wax
obtained was not determined in this study. This result showed that more wax can be
obtained at temperatures lower than 190℃. Owolabi and Amosa (2010) studied the
effective management and potentials of conversion of water sachet to a more useful
product such as super wax. Four different samples wax were formulated, but only
solidification time of 30-60 minutes was observed for each of the samples. Also the
properties of wax such as melting point, density of the wax obtained from the waste
sachets were not determined in this study. In order to produce quality wax that meets
industrial standard with this polyethylene waste, there is need to control the operating
variables such as pyrolysis temperature and time during the pyrolysis process. (William et
al, 1955).
Therefore, in this paper the conversion of used water sachet to polyethylene wax and their
characterization and optimization of shoe polish would be studied. The effect of pyrolysis
temperature, and pyrolysis time, on the yield, and melting point of polyethylene wax
produced from waste water sachets was discussed.

The Existing Technology of the production of shoe polish mainly based on using Inorganic
constitutes, this raw material are their own disadvantage, they are toxic, unhealthy,
environmental impact on the society, due to this it is better to use alternative technology of
producing shoe polish from organic raw materials ( Bee wax , olive oil ), this raw materials
are very important in terms of reducing wastes ,technology transfer ,reducing foreign
currency, cleaning environment ,so that due to this ,it is better use alternative production
process of shoe polish from used water sachet.
5
2.2. Introduction about Shoe polish
Shoe polish is a waxy paste or cream used to shine waterproof or improve and restore the
appearance of leather footwear and products and it, issued both liquid and semi-solid form.
Weather inexpensive or high end, all leather shoes require a good polishing to prolong
their lives and keep them looking new. Shoe polish consists of waxes and solvents. Shoes
polish is available in a number of colors e.g. black, brown, transparent etc. Liquid polishes
are also available where the waxes exist as an emulsion. Shoe polish not only used on
footwear but can also applied to all leather materials including bags, etc. Floor polishes are
pastes, creams, or lotions used to clean, protect, and shine floor. These products originally
made from natural waxes, which were hard to apply and tended to leave a heavy buildup
over time. Today these formulations combine natural waxes and oils with petroleum based
ingredients and synthetic polymers (Secchi., et al, 2005).

Shoe polish products are low-value items that are infrequently purchased, as a single can
be last several months for even the most frequent user. Consumer demand is inelastic and
largely insensitive to price change, while sales volumes are generally low. In the shoe
polish market as a whole, some 26% of turnover is accounted for by pastes, 24% by
creams, 23% by aerosols, and 13% by liquids. In recent years, the demand for shoe polish
products has either been static or declined; one reason is the gradual replacement of
formal footwear with sneakers for everyday use. There are numerous branded products
available, as well as generic store brands. There are two chief areas of shoe polish sales: to
the general public, and to specialists and trade, such as shoe repairers, and cobblers. The
sales percentages between the two outlets are roughly comparable.

Kiwi remains the predominant shoe polish brand most of the world, being sold in over 180
countries but is often see as a mass market product more known for its cheap prices rather
than quality. Today, it is manufactured in Australia, Canada, France, India, Pakistan, South
Africa, Spain, the United Kingdom, and the United States.

6
2.2.1. Composition and Toxicology
Shoe polish consists of a waxy colloidal emulsion, a substance composed of a number of
partially immiscible liquids and solids mixed together. It is usually made from ingredients
including some or all of naphtha, lanolin, olive oil, turpentine oil, wax ( Bee wax), gum
Arabic, ethylene glycol, and if required a colorants, such as carbon black or an azo dye
(such as aniline yellow). It typically has a specific gravity of 0.8, is negligibly soluble in
water, and is made of between 65 and 77% volatile substances—usually naphtha. The high
amount of volatile substances means that the shoe polish will dry out and harden after
application, while retaining its shine. (Ademiluyi F.Taiwo, April 2013).

Lanolinis, hydrophobic grease from wool-bearing animals such as sheep or goats, acts as
both a waterproofing wax and a bonding agent, giving the shoe polish its greasy feel and
texture. It prevents the naphtha from evaporating until the polish has been spread and
buffed into a thin film on the leather surface. An essential ingredient in shoe polish is a
thickener; without this, the polish would be too runny, making it difficult to use. Gum
Arabic, a substance from two sub-Saharan species of the acacia tree, is commonly used to
increase the viscosity of the product.

Shoe polish contains chemical substances which can be absorbed through the skin, or
inhaled. When handling shoe polish, one should ideally wear gloves, and stay in a well-
ventilated area. Shoe polish should be kept out of reach of children and animals. It can stain
the skin for a protracted period of time, and will cause irritation to the eye if there is direct
contact.

2.2.2. Non –toxic Shoe polish

Commercial shoe polish contains various toxic substances. Generally, shoe polish is made
from ingredients including naphtha, lanolin, wax, bicarbonates of potassium and various
types of coloring pigments. It also contains carbonates and bicarbonates of sodium and
potassium. The burning of shoe polish results in the yielding of carbon dioxide, carbon
monoxide and traces of oxides of nitrogen and various toxic materials depending upon the
chemicals, and solvents used to make the shoe polish. To make a good and non –toxic shoe
polish, olive oil, bee wax and sachet wax are collected. Bee wax a tough wax formed from a
mixture of several compounds including hydrocarbons ( 14 % ) , monoesters ( 35 % ),
dieters ( 14 % ),trimesters ( 3 %),hydroxyl monsters (4%),hydroxyl polyesters (8%),acid
esters (1 %),acid polyesters (2%),free acids (12%),free alcohols( 1%) and some
unidentified materials.( Honeybee Natural 2006)
7
2.3 Motivations for the Study
As shown in figure 2.1, Plastic waste is produced by manufacturers and consumers of
products are dumped and burned; this study focuses on consumer plastic wastes from used
water sachets. Obtaining plastics components from used water sachets in a reusable form
and quality is highly doubtful implying that recovered high calorific mixed plastics are most
appropriate for Pyrolysis.

Recycling reduces waste volumes and contributes to energy and resource conservation.
Thermal or tertiary recycling (hydrolysis, pyrolysis or gasification) is a technique that uses
heat to decompose plastics in the absence or limited amount of oxygen for the formulation
of shoe polish. This process applies to mixed plastics from MSW which cannot be cost-
effectively recycled (Noda et al., 2001). The success of this technique is supported by the
economic and energy feasibility resulting from Recuperating and sorting of plastics
,generating income and creating jobs, Thermal conversion is efficient without pollution,
Residue treatment, and waste dumping or landfill costs are minimized
However, depending on the source, type and quality of the waste plastics, the economic
benefits may vary. In addition, markets for certain recycled plastics are only available at
rates of 10-15% of plastics recycled due to their inferior quality and recycling cost
compared to virgin polymers (Williams & Williams, 1997).Due to this it is very efficient to
convert waste plastic, used water sachets in to shoe polish.

Waste plastics dominate

Waste plastics in drainage tracks

Waste plastics dumped

Figure 2.1 Consumer waste plastics form a complex mixture

8
2.4. Theoretical Basis of Plastic Waste
Plastic is a light, durable synthetic material that has found a lot of use in the modern world.
The plastic material comes in various types depending on its application. Polypropylene
(PP) is the most widely used plastic type in the world today followed by Polyethylene
(PE).There are many other forms of other plastics whose applications depend on intended
purpose.

Large production and use of plastics for various applications has resulted in huge volumes
of plastic wastes. This has lead to proliferation in the environment as a result of
accumulation and fragmentation of plastic waste. Most of this waste is non-degradable and
highly resistant to light, acids and other tough conditions. Some of the negative impacts
resulting from poor waste plastic disposal include; choking and starving marine and
wildlife, littering the surrounding environment and blocking drainage systems and water
bodies. Burning of plastics in open fires, landfills or by use of municipal solid wastes (MSW)
incinerators releases toxic gas emissions. These gases include the persistent organic
pollutants (POP’s) such as dioxins. Studies have proved that this gas are carcinogenic and
have endocrine disrupting effects in a wide range. Other emissions include the Green House
Gases (GHG’s) that cause global warming.

The disposal of mixed waste in landfills, dump sites and open burning without material and
energy recovery leads to resource loss, causes health problems, pollution and littering.
Increasing energy demand for industrial and domestic application with rising costs due to
scarcity motivates a constant search for alternative clean energy sources.
Recovering wax from waste presents various incentives e.g. creating jobs, alleviating
poverty, combating and mitigating climate change, protecting the environment and
reducing dependence on traditional fuels sources. Unfortunately, most non-biodegradable,
high calorific value waste fraction (plastics) has little or no application in most developing
world communities. Hence, plastics end up in landfills, surface waters and ocean bed with
serious negative impact on terrestrial and aquatic biodiversity.

Plastic waste with high calorific value (36-46MJ/kg) occupies the greatest portion of
landfill space given their very slow degradability. When openly burned, plastics produce
high pollutants such as VOCs, PAHs and PCDD/F (dioxins). The formation of these
pollutants is not inherent of the polymers but is consequent of limitations of the
combustion process, Hence, using an appropriate technology to transform waste plastic to
sachet wax which is burned and mixed with Bee wax to produce Shoe polish.

9
Polymers can define as materials made from many units. Polymer is seeing as a chain, made
up of various smaller units, these units could be carbon, hydrogen, oxygen, and silicon.
A plastic material is an organic solid, essentially a polymer or combination of polymers of
high molecular mass. A polymer is a chain of several thousand of repeating molecular units
of monomers. The monomers of plastic are either natural or synthetic organic compounds.
The term resin is sometimes used as synonym of a commercial polymer.

Plastics can be classified by chemical structure, i.e. by the main monomer of the polymer's
backbone and side chains. Some important groups in these classifications are the acrylics,
polyesters, polyolefin, silicones, polyurethanes, and halogenated plastics.
Plastics can also be classified by the chemical process used in their synthesis, such as
condensation, and cross-linking. Other classifications are based on properties that are
relevant for manufacturing or product design, e.g. thermo plasticity, biodegradability,
electrical conductivity, density, or resistance to various chemical products.(Alejandro
Villanueva, End-of-waste criteria for waste plastic, 2014).

Majority of plastics that are used today are non biodegradable in nature, they remain in
environment for long period which affects environmental quality. As there is no effective
segregation and recycling system for these plastic waste generated, it Increases load on
landfill sites because of their non-biodegradable nature and ultimately cause
environmental problems like air, soil and ground water pollution as well as loss of marine
biodiversity.

Plastic waste recycling for energy recovery is yet to be exploited in most of the developing
countries where advanced Municipal Solid Waste (MSW) management technologies such as
pyrolysis are yet to be fully implemented. Recycling of post-consumer plastic waste for
shoe polish production through a cost effective and an environmentally friendly process
could become an alternative means of obtaining shoe polish.

2.4.1. Polyethylene (PE)

Polyethylene is a macromolecular hydrocarbon that can be converted into useful products


such as oil and waxes but since the molecular chain of polyethylene is composed of -CH2-,
the freezing point of the diesel obtained is very high and the research octane number of
gasoline is very low near 88. Thus it is not a feasible way to convert polyethylene to oil. It
is, however a profitable way to convert polyethylene waste to polyethylene wax (Jixing et
al., 2003).

10
Waxes derived from petroleum products are basically paraffinic wax and microcrystalline
wax. Several studies have been carried out to produce wax from waste. A study on the
conversion technology of waste polyethylene plastic to polyethylene wax was carried out
by Jixing et al., (2003).

2.4.1.1. Low density polyethylene (LDPE)

In LDPE some of the carbon atoms are attached to three carbon atoms instead of two, this
causes a branch on which other polyethylene chains are attached. These branches are
relatively long and link with other polyethylene molecules. LDPE is like one long piece of
spaghetti, with lots of large pieces of spaghetti attached to it. In contrast to HDPE, LDPE has
more branching that results in weaker intermolecular force, thus lower tensile strength
and hardness. However, LDPE has better ductility than HDPE since the side branching
causes the structure to be less crystalline and easy to be molded.

It has an excellent resistance to water, soft, waxy, and smooth to touch, and has a shiny
appearance. It is normally used in garbage bags, cling wrap, sandwich bags, squeezable
bottles thus widely applied as plastic bags, wrapping foils for packaging, trash bags and
much more. All these items are commonly used in our daily lives and therefore, and LDPE
wastes have a great potential to be used in pyrolysis process since it can produce high solid
yield depends on the set up parameters for shoe polish formulations. LDPE waste has been
accumulated day to day that it is known as the second largest plastic waste. (Shafferina
Dayana Anuar Sharuddin, A review on pyrolysis of plastic wastes, 2016)

2.4.1.2. High density polyethylene (HDPE)

HDPE is characterized as a long linear polymer chain with high degree of crystalline and
low branching which leads to high strength properties. Due to its high strength properties,
HDPE is widely used in manufacturing of milk bottles, detergent bottles, oil containers, toys
and more. The various applications contribute about 17.6% in plastic waste category which
is the third largest plastic type found in municipal solid waste .HDPE wastes have a great
potential to be used in pyrolysis process since it can produce high liquid yield depends on
the set up parameters. Many studies have been conducted on HDPE pyrolysis at different
operating parameters to investigate the product yield obtained. (Shafferina Dayana Anuar
Sharuddin, A review on pyrolysis of plastic wastes, 2016).

11
Used water sachets is Low Density Polyethylene , It has an excellent resistance to water,
soft, waxy, and smooth to touch, and has a shiny appearance, compared with High density
polyethylene , due to waxy nature it is better use LDPE ,for the formulation of shoe polish
instead of HDPE.
The use of low-density polyethylene for packaging treated water is on the increase in
Ethiopia. Polyethylene films (commonly called pure water sachets in Ethiopia) are
therefore seen littering the cities, schools, stadium, wedding reception venues etc. During
packaging of the water, lots of waste polyethylene is generated. These polyethylene films
are non-biodegradable and can remain on the ground for years.
Pyrolysis is a thermal treatment process where waste is subjected to heating in an
atmosphere with a deficiency of oxygen below the stoichiometric combustion level. The
thermal degradation of polyethylene generates a mixture of gases, oils and waxes (Bertolini
et al, 1987).

2.4.2. Plastic Waste (used water sachets) Disposal as a Global Problem

The high calorific value of plastics underscores the need for an alternative material
recovery technology that is affordable, efficient, safe and user-friendly. Little attention has
been paid to using plastic waste as an alternative source especially in the developing
countries which lack technical know-how and appropriate plastic-to-wax technologies.

2.4.2.1. Alternative Technology as Multiple Problem-solution Packages

Developing a waste-to-shoe polish production technology guarantees rational resource


utilization as basis for sustainable development. Although this technology can be use for
both biodegradable and non-biodegradable (plastics) waste, the later is preferred due to
;Plastics are functional, highly versatile leading to increase usage but have low cost-
effective recyclability and are non-biodegradable and disposal by dumping or land filling
offers a global problem with major adverse ecological impacts due photo-degradation, low
compressibility, resilient surfaces, extremely long rotting time and forming of cavities
within air inclusion in landfills etc (Angyal et al., 2007; Biniecka et al., 2005; Blasi, 1997:
Boer et al., 2005).

2.4.3. Properties of Polyethylene

Polyethylene is an addition polymer that is created by the polymerization of ethylene


monomer units, ethylene polymerized by a radical mechanism under very high pressures
and temperatures with the addition of an organic peroxide radical initiator.

12
Polyethylene is creates through polymerization of ethene. It can be produce through free
radical polymerization, anionic addition polymerization, ion co-ordination polymerization
or cationic addition polymerization. This is because ethylene does not have any substituent
groups, which influence the stability of the propagation head of the polymer. Each of these
methods results in a different type of polyethylene.
The process requires a highly purified ethylene feed and the operating pressure ranges
from 1000 to 3000atm and a temperature range of 120 - 3000℃ . This Temperatures
exceeding 3000℃ cause ethylene to decompose and are not recommended in practice
(Dhibet al., 2002).Therefore, the development of mathematical models to predict the
process behavior is important to ensure a stable operation, associated with an
improvement in the properties of the produced polymer (Secchi., et al, 2005).

For initiation, usually peroxides are used. Here, a mixture of different initiators is used;
each of them decomposes into radicals depending on the temperature. In the presence of
radicals, Monomer starts to react with them, forming longer and longer radicals, so-called
living polymer". The third main step in the free radical polymerization process is the
termination step, which ends the reaction.

Polyethylene is probably the polymer we see most in our daily life. It is the most popular
plastic in the world. It has a very simple structure, the simplest of all commercial polymers.
It is produced by addition of polymerization of ethylene CH₂=CH₂.The properties of
polyethylene depend on the manner in which ethylene is polymerized. When catalyzed by
organometalic compound at moderate pressure (15-30 atm), the product is high-density
polyethylene (HDPE), under these conditions, and the polymer chains grow to a very great
length and molecular weight average many hundred thousand.

HDPE is hard, tough and resilient. Most HDPE is use in the manufacture of containers such
as milk bottles and laundry detergent bags. When ethylene is polymerize at high pressure
(1000-2000 atm) and elevated temperature (190-210℃) as well as catalyzed by peroxides
the resulting product is Low-density polyethylene (LDPE).This form of polyethylene has
molecular weight ranging from 20,000-40,000 g and relatively soft and most of them are
used in the production of plastic films such as those used sandwich bags. These polymeric
materials are generally thermoplastic as such are heat convertible and be recycled from
one product to the other type of used-water sachet polyethylene.

13
Used water sachet polyethylene can be recycled in to useful products, However many of
these recycled products e.g., grocery bags, shampoo bottles, toys, footwear, etc are still non-
biodegradable. This will still lead to another environmental disposal (Pollution
problem).(Owolabi, June 2010 ), therefore it is recommended using LDPE as a raw material
for the production of shoe polish using pyrolysis.

2.5. Plastic wastes recycling techniques

2.5.1. Mechanical recycling techniques

It comprises of some processes, which are shredding, melting and pelletizing of waste
plastics. Plastics must be sort prior to mechanical recycling techniques. Mostly, sorting is
performing by manually.
The technology introduced in sorting plastics automatically includes using X-ray
fluorescence, infrared and near infrared spectroscopy, electrostatics and flotation. These
sorting techniques are using in large scale recycling. Owing to the expensive nature of this
sorting technology, sorting will be doing manually. After the sorting exercise, the plastics
are shredded into smaller sizes (between 5 mm2– 10 mm2). The shredded plastics are,
melted and molded directly into a new product or melted and formed into pellets or
granules.

Mechanical recycling refers to the processing of waste plastic by physical means (grinding,
shredding, and melting) back to plastic products. The chemical structure of the material
remains almost the same. At present, the recycling of waste plastic is dominated by
mechanical processes. This recycling path is viable when waste plastics are or can easily by
cleaned and sorted properly. Added to this, the process requires large and quite constant
input.

The five predominant plastic families, i.e. polyethylene (including low density-LDPE, linear
low density-LLDPE, and high density-HDPE), polypropylene (PP), polyvinylchloride (PVC),
polystyrene (solid-PS, expandable-EPS) and polyethylene terephthalate (PET), which are
all thermoplastic, are also the most significant for mechanical recycling. One waste stream
currently being treated in large amounts using mechanical recycling is packaging waste.
(Alejandro Villanueva, 2014)

14
2.5.2. Chemical or feedstock recycling techniques
Feedstock recycling technique describes a range of plastic recovery procedures to make
plastics, which breaks down polymers into their constituent monomers, which in turn, can
be, used again in refineries, or petrochemical and chemical production. Some of the
numerous ranges of feedstock recycling techniques currently being explore include: (I)
Pyrolysis, (ii) Hydrogenation, (iii) Gasification and (IV) Thermal cracking.
Feedstock recycling has a greater flexibility over composition and is more tolerant to
impurities than mechanical recycling. It is very expensive and requires very large
quantities of used plastic for reprocessing to be economically viable.
In practice, chemical recycling or feedstock recycling refer to the same processes, and are
appropriate for mixed or contaminated waste plastics. Processes include:

2.5.2.1. Chemical de polymerization

This process involves the reaction of the plastic polymer with chemical reagents, yielding
its starting monomers that can be processed to produce new polymers. Different processes
exist, depending on the chemical agent; glycolysis, methanolysis, and hydrolysis being the
most common. Chemical de polymerization is only applicable to condensation polymers,
mainly polyesters like PET and nylon, and cannot be used to reprocess addition polymers
such as PE, PP or PVC.(Alejandro Villanueva, End-of-waste criteria for waste plastic, 2014).

2.5.2.2. Thermal cracking (also called pyrolysis)

This involves the degradation of the polymeric materials by heating (usually in


temperatures between 500-800°C) in the absence of oxygen. The plastics are converted
back into the liquid petroleum products used to produce plastics and new plastics,
synthetic fibers, lubricants and gasoline are the end products of the process. It also yields
small amounts of carbonized char and a volatile fraction that may be separated into
condensable hydrocarbon oil and a non-condensable high calorific gas that can be reused
onsite. Therefore, the classification of the pyrolysis process as recycling (tertiary/feedstock
recycling) or recovery may vary depending on the final use of the resulting use of output
fractions.
The proportion of each fraction and their composition depends primarily on the nature of
the waste plastic but also on process conditions. Thermal de polymerization of poly olefins,
such as PE or PP, tends to break into a variety of smaller hydrocarbon intermediates

15
whereas cracking of some other addition polymers, such as PS and poly methyl
methacrylate, yields a high proportion of their constituent monomers.
The main advantage of this technology when it is integrated with a traditional mechanical
recycling process is that it can recycle mixed or commingled streams of plastics with high
levels of contamination. Germany and Japan have several such plants already in
operation.(Alejandro Villanueva, End-of-waste criteria for waste plastic, 2014).

2.5.2.3. Catalytic conversion (also called catalytic cracking)

This involves the degradation of the polymers by means of catalyst. This type of conversion
offers many advantages compared to thermal cracking including lower degradation
temperatures and consequently lower energy consumption, higher conversion rates, and a
narrower distribution of hydrocarbon products. Most processes produce higher quality
fuels (gasoline and diesel fractions), gaseous olefins and aromatic compounds for the use as
raw materials. Therefore, the classification of the catalytic cracking process as recycling
(tertiary/feedstock recycling) or recovery may vary depending on the final use of the
resulting use of output fractions.(Alejandro Villanueva, End-of-waste criteria for waste
plastic, 2014).

2.5.2.4. Gasification

Gasification refers to the production of synthesis gas (syngas) by partial oxidation of


organic matter at high temperatures (typically between 1200-1500°C) under mildly
oxidizing condition (usually steam, CO2 or sub-stoichiometric oxygen) which differs from
the incineration process. Syngas, which consists primarily of CO and hydrogen and is free of
dioxins and furan compounds, can be used in the synthesis of chemicals (e.g. methanol and
ammonia) and to produce synthetic diesel, or may be combusted directly as a fuel.

2.5.2.5. Coke oven chemical feedstock recycling

Plastics can substitute part of the coal used to generate coke for use as the reducing agent
in coke ovens (as in blast furnace process above). Hydrocarbon oil and coke oven gas, also
produced during this process, are used, respectively, as chemical feedstock and to generate
electricity. The classification of the coke oven chemical process as recycling
(tertiary/feedstock recycling) or recovery may vary, depending on the use of output
fractions.
As the products of chemical/feedstock recycling processes may be used both as raw
chemicals or fuels, there is no classification of these processes as closed-loop recycling or
16
open-loop recycling, as different compounds can be obtained and used for two different
purposes. Consequently, the environmental assessment of one chemical recycling process
may even vary depending on the end uses of each plant. Even if the cracking of plastics into
its monomers may be more energy intensive than mechanical recycling, a chemical
recycling process may have greater environmental benefits than a mechanical
downgrading process, depending on the final product’s quality.

Chemical recycling is an elegant concept, and despite attracting scientific attention, it has
not been widely commercialized so far because the process economics and because the
quality of the products is lower than normal commercial grade feedstock. Also, back-to-
monomer recycling is so far only operational for certain types of polymers (PU, PA and
polyester) while back-to-feedstock recycling (splitting polymers into raw materials
substituting fuel or gas) is less demanding.(Alejandro Villanueva, End-of-waste criteria for
waste plastic, 2014)

2.6. Pyrolysis of plastics

Fundamentally, different types of plastics have different compositions that normally


reported in terms of their proximate analysis. Proximate analysis can be defined as a
technique to measure the chemical properties of the plastic compound based on four
particular elements which are moisture content, fixed carbon, volatile matter and ash
content. Volatile matter and ash content are the major factors that influence the liquid oil
yield in pyrolysis process. High volatile matter favored the liquid oil production while high
ash content decreased the amount of liquid oil, consequently increased the gaseous yield
and char formation. (Shafferina Dayana Anuar Sharuddin, A review on pyrolysis of plastic
wastes, 2016).These characteristics indicate that plastics have high potential to produce
large amount of wax through pyrolysis process. Since the results of plastics proximate
analysis are very convincing, the following discussion would focus more on the process
parameters involved during the pyrolysis process that would have major influence in the
wax production. (Shafferina Dayana Anuar Sharuddin, A review on pyrolysis of plastic
wastes, 2016).

2.6.1. Pyrolytic process parameters condition

Parameters play major role in optimizing the product yield and composition in any
processes. In plastic pyrolysis, the key process parameters may influence the production of
final end products such as liquid oil, gaseous and char, waxy. Those important parameters

17
may be summarized as temperature, type of reactors, pressure, residence time, catalysts,
type of fluidizing gas and its rate. The desired product can be achieved by controlling the
parameters at different settings. In-depth discussions of the operating parameters are
reviewed in the following subsections. (Shafferina Dayana Anuar Sharuddin, A review on
pyrolysis of plastic wastes, 2016)

2.6.1.1. Temperature

Temperature is one of the most significant operating parameters in pyrolysis since it


controls the cracking reaction of the polymer chain. Molecules are attracted together by
Van der Waals force and this prevents the molecules from collapsed. When temperature in
the system increases, the vibration of molecules inside the system will be greater and
molecules tend to evaporate away from the surface of the object. This happens when the
energy induced by Van der Waals force along the polymer chains is greater than the
enthalpy of the C–C bond in the chain, resulted in the broken of carbon chain. (Shafferina
Dayana Anuar Sharuddin, A review on pyrolysis of plastic wastes, 2016).

2.6.1.2. Type of reactors

The type of reactors has an important impact in the mixing of the plastics and catalysts,
residence time, heat transfer and efficiency of the reaction towards achieving the final
desired product. Most plastic pyrolysis in the lab scale were performed in batch, semi-
batch or continuous-flow reactors such as fluidized bed, fixed-bed reactor and conical
spouted bed reactor (CSBR).

2.6.1.3. Residence time

Residence time can be defined as average amount of time that the particle spends in the
reactor and it may influence product distribution. Longer residence time increases the
conversion of primary product, thus more thermal stable product is yielded such as light
molecular weight hydrocarbons and non-condensable gas. Nevertheless, there is a
temperature limitation in the process that may influence the product distribution where
until that instant; the residence time has not much effect on the product distribution.
(Shafferina Dayana Anuar Sharuddin, A review on pyrolysis of plastic wastes, 2016).

After reviewing literature on modern waste disposal technologies and the challenges of applying
them in developing countries, shoe polish formulation from plastic waste has been given little

18
or no attention; therefore this thesis research will use the pyrolysis technology to produce wax
from used water sachets, compared with other technologies.

2.7. Natural Wax

Waxes are a diverse class of organic compounds that are hydrophobic, malleable solids
near ambient temperatures. They include higher alkanes and lipids, typically with melting
points above about 40 °C (104 °F), melting to give low viscosity liquids. Waxes are
insoluble in water but soluble in organic, non-polar solvents. Natural waxes of different
types produce by plants and animals and occur in petroleum.
Waxes are organic compounds that characteristically consist of long alkyl chains. Synthetic
waxes are long-chain hydrocarbons (alkanes or paraffin) that lack substituted functional
groups. Natural waxes may contain UN substituted hydrocarbons, such as higher alkanes,
but may also include various types of substituted long chain compounds, such as fatty
acids, primary and secondary long chain alcohols, ketones and aldehydes. They may also
contain esters of fatty acids and long chain alcohols.

2.7.1. Plant and animal waxes

Waxes synthesized by many plants and animals, those of animal origin typically consist of
wax esters derived from a variety of carboxylic acids and alcohols. In waxes of plant origin,
characteristic mixtures of UN esterifies hydrocarbons may predominate over esters.

2.7.1.1. Animal waxes

The most commonly known animal wax is beeswax, but other insects secrete waxes. A
major component of the beeswax used in constructing honeycombs is the ester
myricylpalmitate which is an ester of triacontanol and palmitic acid. Its melting point is 62-
65 °C. Spermaceti occurs in large amounts in the head oil of the sperm whale. One of its
main constituents is cetylpalmitate, another ester of a fatty acid and a fatty alcohol. Lanolin
is a wax obtained from wool, consisting of esters of sterols.

2.7.1.2. Plant waxes

Plants secrete waxes into and on the surface of their cuticles as a way to control
evaporation, wet ability and hydration. The epicuticular waxes of plants are mixtures of
substituted long-chain aliphatic hydrocarbons, containing alkanes, alkyl esters, fatty acids,
primary and secondary alcohols, diols, ketones, aldehydes. From the commercial
perspective, the most important plant wax is carnauba wax, a hard wax obtained from the

19
Brazilian palm Coperniciaprunifera. Containing the ester myricylcerotate, it has many
applications, such as confectionery and other food coatings, car and furniture polish, floss
coating, surfboard wax and other uses. Other more specialized vegetable waxes include
candelilla wax and ouricury wax.

2.7.2. Bee Wax

Bee wax produced from a long chain of alcohols, this alcohol was reported to give a neutral
compound on treatment with strong alkali in contrast to the alcohols of a plant. This would
mean that bee wax alcohol was a secondary alcohol which was dehydrogenated to ketones,
or the neutral material would have been hydrocarbon impurities in the alcohols.
Fractionation on a silicsic acid column gave hydrocarbons (37%), Monoesters (29%) and a
more polar fraction (34 %).

2.7.2.1. Bee wax use at present

Besides its use for foundations, which is probably the main use, wax is also used for
following purposes: cosmetics 25-30 %, pharmacy 25-30 %, candles: 20 % and other
purposes: 10-20 %.From the above different types of wax it is better to use bee wax for the
formulation of shoe polish because bee wax is waxy organic raw materials ,non toxic,
flexibility of operation, easily availability in Ethiopia compared to other types of wax, due
to this it I recommend using bee wax as a raw material for shoe polish formulation.

2.8. Research Methodology Frame Work


An integrated methodology that involved the assessment of raw material characteristics
and availability, and optimization of the sample preparation using pyrolysis technology and
evaluation of its economic and application efficiency was adopted. The methodology was
classified into blocks as shown in Fig.2.2

20
Problem identification & analysis

Literature review

Research methodology

Field Studies Experiments: raw Experiments: raw


material preparation & material preparation &
sample analysis sample analysis

Figure
Observation Interviews & Characterization
personal Sample and laboratory Design &
communication preparation analysis Optimization

Figure2.2 Schematic representation of methodology frame work

21
The optimization process involved various laboratory evaluation and statistical analysis (Fig.
2.3).

Evaluation & optimization of pyrolysis process

Raw material preparation Laboratory experiments

Proximate Measurement of mass & energy


analysis variables Shoe polish formulation

Mass & energy balance calculations

Figure 2.3 Optimization stages

22
Chapter Three
3. Materials and Methods
3.1. Materials
Equipment’s and materials used for this analysis was, batch reactor, cutting mill, Electric
heater, water bath, electric heater, electric mixer, temperature controller, bee wax,
thermocouple, lagging materials, beaker to receive the wax and weighing balance, gloves ,
scissors , polyethylene bags ,waste low density polyethylene films (used water sachet),
lagging materials, test tubes, muffle furnace, crucible, desiccators, cylinder, cotton,
formulated shoe polish, commercial shoe polish (Kiwi), rotary viscometer, water bath, test
tube, thermometer, cylinder.

3.2. Methods
3.2.1 Bee Wax Melting
The wax was melted in water bath at a temperature of 70℃.

3.2.2. Pyrolytic Reactor Process

The pyrolysis process was conducted in a pyrolysis reactor made of mild steel and stainless
steel. The reactor has a height of 20 cm, an external diameter of 11 cm and an internal
diameter of 8 cm and a 2 kW electric coil. The reactor was capped with a ball valve to make
it airtight and fitted with an outlet tube system at the top. The tubes had an outer diameter
of 300 mm and an inner diameter of 200 mm. A pressure gauge of 1- 250 bars was
connected to the top of the reactor. A thermocouple with digital temperature readout was
connected to the reactor to control and monitor the internal reaction temperature during
the pyrolysis process. high purity nitrogen gas was purged into the reactor at a flow rate of
2 L/min to maintain an oxygen free environment. The reactor was heated to a temperature
range of 100 to 200 °C using a 2 Kw electric coil for a period of 30-60 minutes.

3.2.3. Pyrolysis of used water sachet plastics

Batches of 100 g of used water sachet were introduced in the pre- warmed reactor between
100 - 200 °C. Nitrogen gas was purged into the reactor, at a flow rate of 2 L/min. The
sample was heated at temperatures ranging between 100-200 °C and with heating rate of
10 °C /minute. The non-condensable gases produced from the reactor were evacuated
using the outlet tube system. The sachet wax was weighed for each batch and stored in pre-
cleaned desiccators. Optimization studies were carried out by varying reactor temperature

23
within the range of 100-200 °C and 10 °C /minute. Reaction times were also varied. The
effects of temperature, reaction times were correlated.
3.2.4. Preparation of shoe polish from Bee wax and used water sachet
3.2.4.1. Preparation of shoe polish

Used water sachets were collected, washed and dried to make them clean. They were
weighed into samples of 100g each. Each of these samples was charged into a batch
pyrolytic reactor, at three different temperatures and different reaction time ( 100
℃ , 150 ℃ , 200 ℃ ). The reactor was placed on a heated source. For each sample, the
temperature and reaction time was noted, to enable the determination of temperature and
time at which highest yield of wax was obtained. Bee wax was melted along with the wax
obtained from used water sachets. The two waxes were properly mixed and then stearic
acid was added and stirred .Thereafter, Olive oil was introduced while still stirred to
ensure a proper mix .The mixture was allowed to cool to 41°C and poured into a container
for storage. The polish was allowed to set.

3.2.4.2. Shoe Polish Formulations and their Mixing Ratio

Three different formulations of polish were prepared and labeled samples A (100℃), B
(150℃ ) and C (200℃), the three samples were also compared with the standard polishes
labeled D (Kiwi). The densities, melting points and viscosities of shoe polishes produced
and that of control (Kiwi) polishes were determined using ASTM standard methods.
Table 3.1 Shoe Polish Formulations

Ingredients Sample A ( % ) Sample B ( % ) Sample C ( % )


Sachet wax 20 33 25
Bee wax 25 15 30
Fragrance 12 12 8
Olive oil 43 50 37

24
3.2.5. Proximate analysis of used water sachets
3.2.5.1. Ash content determination

The nearest 0.1mg of 1gm sufficient dry used water sachets was measured, and the nearest
0.1mg empty crucible was weighed. The sample was put into a crucible and the crucible
was ignited in the muffle furnace at 725℃for 1 hour 30 minutes and then the crucible was,
placed in the desiccators. Finally, the sample was cooled to a room temperature, and
weighed to the nearest 0.1 mg.

The ash content Ac is given in % by:


Calculate the percentage of ash content (weight basis) as follows

mass of empty crucible− mass of crucible plus dried sample


% ASC = *100 (3.1)
mass of crucible plus dried sample−mass of empty crucible

3.2.5.2. Volatile Matter Content determination

The temperature of the muffle furnace was adjusted to 800℃ and the steady temperature
condition in the furnace was maintained. The weight of crucible was measured. About 1g
of the sample was weighed; the sample was putted into crucible and after placed the lids on
the crucible and was transferred into the muffle furnace and leaved exactly for 8 min at
800℃. Finally, it was allowed to cool by placed the crucible in the desiccators to room
temperature and weighed to the nearest 0.1mg.
The volatile matter content on dry basis, VD in% is given by:

VD= [(100*(B−F) −Mc (B−G))* (B−G) (100−Mc)] ∗100 (3.2)

Where B=mass in g of the crucible and sample before heating, F= mass in g of the crucible
and contents after heating, G= mass in g of the empty crucible, Mc= % of moisture content

3.2.5.3. Fixed Carbon Content determination

The fixed carbon content, was determined by subtracted the sum of percentage
compositions of moisture content, volatile matter content, and ash content form 100.
3.2.6. Characterization of Polyethylene wax
3.2.6.1. Standard Test Method for Melting Point of Polyethylene Wax

A quantity of wax was put in a dish and placed on an electric heater. A thermometer was
placed in a dish to monitor the temperature.

25
The air bath was supported in its proper position in the water bath, filled the water bath to
within 13 mm (1⁄2 in.) of the top with water at a temperature of 16 to 28°C (60 to 80°F).
The bath temperature is kept within these limits throughout the test. The wax sample was
heated to at least 8°C (15°F) above its expected melting point (70 °C - 90 °C). To heat the
wax sample use a suitable container in an oven or water bath which is held at a
temperature not exceeding 93°C (200°F). Avoid the use of direct heat such as flame or hot
plate. Do not keep the sample in the molten state longer than 1 h. Fill the test tube to a
height of 51 mm (2 in.) with the melted sample. Insert the melting point thermometer
through the center of a cork so that the 79-mm (31⁄8-in.) immersion line is at the lower
surface of the cork. The cork was inserted into the test tube so that the bottom of the
thermometer bulb was 10 mm (3⁄8 in.) from the bottom of the test tube. The test tube was
supported assembled in the water bath as shown in Figure 3.6 while the temperature of the
molted wax was still at least 8°C (15°F) above its expected melting point.

The melting point of bee wax recorded by thermometer at every 15 s. Record each reading
to the nearest estimated 0.05°C (0.1°F). The progressed reported result was used to
determine the appearance of the plateau. Identify the plateau as the first five consecutive
readings all of which agree within 0.1°C (0.2°F).Discontinued the test after obtained these
five plateau readings.

3.2.6.2. Density determination of Polyethylene wax by Measuring Cylinder

A quantity of wax was put in to a beaker and weighed. The sample was weighed out to the
nearest 0.1 gram and then the sample, transferred in to a suitable graduated cylinder. The
base of the cylinder was gentled taped on a slightly resilient surface, such as a rubber pad
or book, until the height of the sample in the cylinder is at a minimum, and the sample
height does not reduce with further tapped. Finally reading volume of a sample in cc (ml)
was recorded. The change in volume was noted and recorded.
3.2.7. Characterization of shoe polish
3.2.7.1. Viscosity Determination by Rotary Viscometer Method

In this test method, the shoe polish was placed in a glass tube, housed in an insulated block
at a fixed temperature. A metal spindle is then rotated in the shoe polish at a fixed rpm (10
rpm), and the torque required to rotate the spindle is measured. Based on the internal
resistance to rotation provided by the shear stress of the shoe polish, the shoe polish
absolute viscosity can be determined. Absolute viscosity is reported in centipoises (CP),

26
equivalent to Pa*s in SI units. This method is commonly referred to as the Brookfield
method and is described in ASTM D2983.

3.3. Evaluation of the Performance of Shoe Polish& Compared with


Commercial Product
The polished and shined leather samples were tested on some physical parameters as
follows:

3.3.1. Luster/Gloss

The polished samples were examined for their gloss/luster by comparing them with one
another (Sample A, Sample B, Sample C . with commercial product sample D).

3.3.2. Rub Resistance

The polished leather samples were rubbed with white and clean cotton material for about
40 times. The change in hue and level of staining were examined.

3.3.3 Fading Resistance

The polished leather samples were tested for fading resistance by exposing them to the sun
for 74hrs. Finally, change in hue and gloss was used to assess the parameter.

3.3.4. Dust Absorption Resistance

The polished leather samples were exposed to an open environment, where dust can get
easy access to them for 24hrs. The level of dust adsorption was examined.

3.3.5. Wrinkle/Crease Resistance

The polished leather samples were each held at both end and creased as if washed garment
to see if the polish was peeled off the leather.

3.4. Optimization of process Parameters

The formulated shoe polish with three parameters with three factors (A, B, C) and three
levels (1, 2, and 3) were selected to build a proper experimented was optimized by using
experimental design expert.

27
3.5. Techno-Economic Feasibility Study

The techno-economic feasible study for shoe polishes production for major unit operations.
Assumptions were made based on literature review. Cost estimation for solid processing
plant using percentage of delivered equipment cost and estimation of total production cost.

28
Chapter Four
4. RESULT AND DISCUSION
4.1. Formulated polyethylene wax from used water Sachets

Table 4.1 .Reaction temperature, time and Yield of Polyethylene wax

SN. Pyrolysis Pyrolysis Yield of sachet


Temperature(℃) time(min) wax (%)
1 100 30 31.64
2 100 45 35.4
3 100 60 32.9
4 150 30 29.4
5 150 45 23.7
6 150 60 19.6
7 200 30 16
8 200 45 12
9 200 60 8

4.1.1Design Expert Output ( yield )

4.1.1.1. Response output of yield

Design Expert Output


ANOVA for Selected Factorial Model
Table 4.2 Analysis of variance table [Partial sum of squares]

Source Sum of DF Mean F value Prob>F( Significant )


Square Square
Model 730.39 4 182.60 18.77 0.0074
A 685.55 2 342.78 35.24 0.0029
B 44.84 2 22.42 2.30 0.2158
Residual 38.91 4 9.73
Cor 769.30 8
Total

29
The Model F-value of 18.77 implies the model is significant. There is only a 0.74% chance
that a "Model F-Value" this large could occur due to noise.Values of "Prob > F" less than
0.0500 indicate model terms are significant. In this case A are significant model terms.
Values greater than 0.1000 indicate the model terms are not significant.

If there are many insignificant model terms (not counting those required to support
hierarchy),model reduction may improve the model.Both factors, Temperature (A) and
Time (B) are significant.

Design-Expert Plot Interaction Graph


B: Time (min)
Yield 35.4 2
2

X = A: Temperature 2
Y = B: Time 2

Design Points 28.55


2

B1 30
B2 45
B3 60 Yield 2

21.7
2

2
14.85

8 2

100 150 200

A: Temperature ( ℃ )
Figure 4.1interaction graph of yield

The effect of pyrolysis temperature and time on the yield of polyethylene (sachet) wax is
shown in Figure 4.1. At high pyrolysis temperature, the decrease in wax yield is very
obvious. It can be seen from Figure 4.1 that, the yield is 8-35.4 % at the pyrolysis

30
temperature range of 100°C-200°C, when the polyethylene waste (pure water sachet) was
pyrolysed to polyethylene wax, above 200℃ , the sachets melted into fuel oil.

Similar trend was observed by Jixinget al., (2003) while pyrolysing waste plastics to
produced polyethylene wax. Therefore 100°C and 45 min are the optimal temperature and
the optimal reaction times in other to produce wax with high yield i.e., over 30%. But these
optimal temperatures and optimal reaction times will only be acceptable, the melting point
of wax produced are within ASTM standard wax.
It was also observed that when the polyethylene wastes water sachet was pyrolysed at
temperature 100°C, the yield decreases sharply from 31.4 % to 8 % as the pyrolysis time
was changed from 30 to 60 minutes. At the same reaction time with an increase in
pyrolysis temperature, the yield decreases. This is a very significant trend.
Conditions would operated this process at a temperature set at 100 ℃ and Time 45 min at
the high level give the highest yield.

At the same reaction time with an increase in pyrolysis temperature, the yield decreases.
This is a very significant trend.
There are two reasons for the decrease in yield, one is the pyrolysis of wax to more gaseous
products as the temperature increases; the other reason is the vaporization of wax when
pouring from the reactor into the mould.

Design-Expert Plot One Factor Plot


Yield 35.4
X = A: Temperature
Design Points
Actual Factor 28.55
B: Time = 30 Yield
21.7

14.85

8
100 150 200
Temperature ( ℃ )

Figure 4.2 One Factor Plot of Yield vs. Temperature

31
It was observed that, at the same pyrolysis temperature, the yield decreased with the
increase of pyrolysis time.
One Factor Plot
Design-Expert Plot
Yield 35.4
X = B: Time
Design Points
Actual Factor 28.55
Yield
A: Temperature = 100 21.7

14.85

8
30 45 60
B: Time (min)

Figure 4.3 One Factor Plot of Yield vs. Time


Conditions would operated this process at a temperature set at 100 ℃ and Time 45 min at
the high level give the highest yield.35.4
Table 4.3Constraints and optimaization
Parameter Goal Lower Upper Lower Upper
Limit Limit Weight Weight
Temperature is in range 100 200 1 1
Time is in range 30 60 1 1
Yield Maximize 8 35.4 1 1

Table 4.4. No of available Solutions & their Desirability

SN Temperature Time Yeild Desirability


(℃ ) (min )
1 100 45 35.4 1
2 100 60 32.9 0.909
3 100 30 31.64 0.863
4 150 30 29 0.766
5 150 45 23.7 0.573
6 150 60 19.6 0.423
7 200 30 16 0.292
8 200 45 12 0.146

32
4.2. Characterization Results
4.2.1. Proximate Analysis of a Raw Material

The Proximate Analysis result of used water sachet determines the distribution of its
contents. It may be noted that the volatile matter present, in used water sachets,
contributes maximum to its contents. The moisture content present in the sample can also
be considered as water vapor when it is heated to high temperatures. Hence, about 92.5 %
was volatile matter and almost negligible moisture content. The values from the Table 4.1
indicates that the ash content of the sample was 0.5 %.This gives an overview about the
properties and components of used water sachet.
Table.4.5. Proximate Analysis of used water sachet

Used water sachet content ( components ) Composition ( % )


Ash Content 0.5
Moisture Content 0
Volatile Matter 99.5
Fixed carbon Content 0

Proximate Analysis Result

Volatile Matter ( 99.5 % )

Ash Content (0.5 % )

Fixed Carbon ( 0 % )

Moisture Content ( 0 % )

Figure 4.8 Proximate analysis results

33
4.2.2. Melting point
The melting point of wax at different pyrolysis temperature and time was shown in Table
4.6 below.
Table 4.6 Melting point result at different temperature and time

SN. Temperature Pyrolysis Melting


(℃) time(min) point ( ℃ )
1 100 30 125
2 100 45 112
3 100 60 111
4 150 30 120
5 150 45 88
6 150 60 76
7 200 30 80
8 200 45 72
9 200 60 65

The properties of the wax produced from used water sachets before it was used to
formulate polish after pyrolysis is shown in Table 4.7. These parameters were measure
before additives (like Olive oil, stearic acids etc) were added to the shoe polish. The wax
produced at pyrolysis temperature 100°C was used to produce the polish. The melting
point of the wax is 76℃, while the density is 0.741g/ml.

Table 4.7 Properties of sachet Wax Produced from waste water sachets

Process Parameters Optimum Values


Pyrolysis temperature 100℃
Melting Point 76 ℃
Density @ room temperature 0.741 g/ml

34
4.2.2.1. Response output of Melting Point

Response :-Melting Point


Anova for selected Factorial Model
Table 4.8 Analysis of variance table [Partial sum of squares]of melting point

Source Sum of DF Mean F value Prob>F


Squares Square Significant
Model 3809.33 4 952.33 11.88 0.0171
A 2860.67 2 1430.33 17.84 0.0102
B 948.67 2 474.33 5.92 0.0638
Residual 320.67 4 80.17
Cor Total 4130.00 8

The Model F-value of 11.88 implies the model is significant.There is only


a1.71% chance that a"Model F-Value" this large could occur due to noise.
values of "Prob > F" less than 0.0500 indicate model terms are significant.
In this case A is significant model terms.

If there are many insignificant model terms (not counting those required to support
hierarchy), model reduction may improve your model. Both factors, Temperature (A) and
Time (B) are significant.

35
Design-Expert Plot Interaction Graph
Melting Point B: Time
125
X = A: Temperature
Y = B: Time
Design Points 110
B1 30
B2 45
B3 60
Melting Point ( ℃ ) 95

80

65

100 150 200

A: Temperature ( ℃ )

Figure 4.9interaction graph of melting point


The melting point of polyethylene wax was determined by its molecular weight range and
the extent of the pyrolysis of polyethylene, The deeper the pyrolysis, the lower the
molecular weight range, the lower the melting point.
Figure 4.9 shows that with an increase in pyrolysis time, the melting point of polyethylene
wax decreases. It can be seen that if polyethylene waste water sachet was pyrolysed at the
temperature range 100°C to 200°C, the melting point of polyethylene wax varies from 65°C
to 125°C. At 100°C the waste sachets were not fully pyrolysed to wax so the melting point
was not determined at this temperature. At a temperature of 150°C the melting point
decreases sharply with a sudden decrease in slope after 30 minutes as shown in Figure-6.
In this study polyethylene wax with melting point of 125-65°C was obtained at 100°C to
200°C waste from the waste sachets, Jixinget al., (2003) obtained a melting point of 144°C-
104°C while pyrolying waste plastics. Standard wax property requires that the melting
point of wax should be between 60-93°C for microcrystalline wax (Wax properties, 2010).
Conditions would operated this process at a temperature set at 100 ℃ and Time 30 min at
the high level give the highest melting point.

36
Design-expert Plot One Factor Plot
Melting Point 143.102
X = A: Temperature
Design Points
Actual Factor 123.576

B: Time = 30 104.051
Melting Point ( ℃ )
84.5255

65
100 150 200
A: Temperature ( ℃ )

Figure 4.10One Factor Plot of melting point vs. Temperature


At a temperature of 150°C the melting point decreases sharply with a sudden decrease in
slope after 30 minutes as shown in Figure 4.10.
One Factor Plot
Design-Expert Plot
Melting Point 143.102
X = B: Time
Design Points
Actual Factor 123.576

A: Temperature = 100 104.051


Melting Point(℃)
84.5255

65
30 45 60
B: Time (min)

Figure 4.11One Factor Plot of melting point vs. Time


The increase in pyrolysis time, the melting point of polyethylene wax decreases. It can be
seen that if polyethylene waste water sachet was pyrolysed at the temperature range 100 -
200°C.

37
4.3. Thermo physical Properties of Shoe Polish
4.3.1. Melting Point of shoe polish

Figure 4.16 shows the thermo physical properties of polishes produced from waste water
sachet wax and other known standard polish. Samples A, B and C were prepared using the
formulated shoe polish discussed earlier while sample D is the control samples which are
Kiwi. The melting point of sample D which is Kiwi control polish was the highest followed
by sample A which contains only 20 % wax produced from waste sachets. In the analysis,
sample D (Kiwi polish) had the highest melting point followed A and then B and C which
had the highest melting point. Sample B & C has the highest melting point and contains
more waste polyethylene sachet wax of about 33 and 25 % respectively. This shows that
the percentage of waste sachet wax required for formulated shoe polish should not exceed
33%.
Table 4.9 Melting Point of shoe Polish

SN. Formulated& Controlled Shoe Response


Polish Melting Point (℃ )
1 A 24
2 B 65
3 C 60
4 D 30

38
Design-Expert Plot One Factor Plot

Melting Point 65
X = A: p

Design Points
54.75

Melting Point (℃ )

44.5

34.25

24

A B C D

A: p

Figure 4.16.Melting point of formulated & controlled shoe polish


4.3.2. Density of Shoe Polish
Table 4.10 Density of shoe polish

SN. Formulated & Controlled Shoe Response


Polish Density ( g/ml )
1 A 0.54
2 B 0.67
3 C 0.59
4 D (KIWI) 0.61

39
Design-Expert Plot One Factor Plot

Density 0.68
X = A: Sample type

Design Points
0.64575

Density (g/𝑚𝑙 ) 0.6115

0.57725

0.543

A B C D

Sample type

Figure 4.17 Density of formulated and controlled shoe polish


The density of shoe polish sample B and C are compared favorably with that of samples D
(control polishes) than sample A. Sample B had more dense than sample A and C.
4.3.3. Viscosity of Shoe Polish at Different Temperatures
Table 4.11 Viscosity of shoe polishes at different temperature

Temperature ( ℃ ) Viscosity of Formulated and Control polish


A B C D
40 2.2 6.45 0.88 8.23

50 2.01 3.15 0.62 3.66

60 0.63 1.34 0.2 3.13

40
Design-Expert Plot One Factor Plot

Viscosity 8.23
X = A: Temperature
Design Points
5.82115
Actual Factor
B: formulated and control
Shoe polish = A
3.4123
Viscosity

1.00344

-1.40541

40 50 60

A: Temperature ( ℃ )

Figure 4.18 Model graph one factor plot of viscosity vs. Temperature

41
Design-Expert Plot One Factor Plot
Viscosity
X = B: formulated shoe 8.3737
polish
Design Points 6.3303
Actual Factor 1

4.2868
Viscosity
A:
Temperature = 40 2.2434
4

0.
2 A B C D

B: formulated and control shoe


polish

Figure 4.19 Model graph one factor plot of viscosity vs. formulated Shoe polish
From the Figure 4.19 shows, the viscosity of shoe polishes formulated A, B, C & the control
polishes D at different temperatures. The increase in temperature affects the viscosity of
the samples. Viscosity value decreased with increase in temperature for all samples,
polishes labeled sample B formulated using 33 % water sachets was hard compared with
sample A and C at 40-60℃. Generally viscosity of the polishes decreases with temperature.
Viscosity of polish produced using sample B compared favorably with control polish
sample D than sample A and C at 50℃.

42
4.4. Performance of Shoe polish& Compared with Commercial Product
Table 4.12 Physical tested of shoe polish

Physical Formulated Shoe Polish Kiwi ( D )


Property
A B C

Luster / gloss Good Very Good Good Very Good


Rub Resistance Very Good Good Good Very Good
Fading Resistance Very Good Very Good Very Good Excellent
Dust Absorption Good Very Good Good Excellent
Resistance
Wrinkle / Crease Good Very Good Good Very Good
Resistance

From the resulted in table 4.12 it is observed that, Sample B and commercial shoe polishes
exhibited, a very good gloss. Which comparably shown by the polish from polyethylene
sachet wax. This is due to the tinting strength of polythene and its excellent interaction
with solvent, oil (Turner, 1993and Morgans, 1990). Shoe polish from polythene showed
good rubbing resistance, which is inferior to sample A and commercial (D) shoe polishes,
but the same with sample C shoe polish. The fading resistance of the formulated shoe
polish (Sample B) showed almost the same with that sample A and C shoe polish but
inferior to that of Commercial shoe polish. This is due to smooth texture and tinting
strength of the polythene. (Gumel, 2006).
Polyethylene (Sample B) exhibited a very good resistance to dust similar to that
commercial shoe polish (D), but Superior to that of carbon Sample A and polishes. This was
attributed to the small particle size and smooth texture of the polythene (Christie, 1993).
The shoe polish produced from polyethylene wax (Sample B) showed a very good wrinkle
resistance, which the same was in compared with that of Commercial, but superior to that
of sample A and Sample C. This is due to the excellent interaction of the polyethylene wax
with the reagents used and adhesion of the polish to the finished leather (Guthrie and Lin,
1994).

43
Chapter Five
5. MATERIAL AND ENERGY BALANCE
5.1. Heat and Mass Balance Analogies
Matter is transformed to energy when C-C and C-H chains break on heating at high
temperature, forming various inflammable monomers, active molecular groups and other
smaller molecules which are burned.
Table 5.1 an analogy of heat and mass transfer
Nature Heat transfer Mass transfer

Transfer of Thermal energy Transfer of chemical components from


within a single phase a donor to host phase within a phase

Molecular movement Heat conduction in metal and Diffusion and transfer of hot gases
in closed systems transfer of hot gas stream involving phase changes
Mechanisms

Radiation Thermal radiation No mass radiation

Macroscopic Convective and conductive heat Convective mass transfer (molecules)


movement (gases) Transfer

Technical meaning Favoring Heat transfer Cracking of polymer plastics, transfer


(temperature gradient) Of pyrolysis-synthesis gases to
Prevention of heat transfer by combustion chamber and burning
insulation and isolation

Transport equation Heat and material flow rates and driving forces (temperature,
concentration and pressure)

Transport area Heat transfer surface Mass of hot gases

Driving Forces and Temperature difference Concentration, composition, phase


intensive variables change and pressure differences

Examples Heat conduction, radiation and Drying and dissolving of solids,


convection (free and forced) absorption of gases and distillation

This process involves a dynamic mass and heat transfer system ensuring effective resource
recovery from waste. A careful evaluation of the energy and mass balance analysis of the
simplified process is absolutely necessary to ascertain the environmental friendliness of
the technology.

44
5.1.1. Energy and Mass Input and Output in a Process
Material and energy output

Gaseous products formed:


Mp1, mp2, mp3…mpn
Material and
energy input
Wax produced: Mw1, mw2,
mw3…mwn
Input materials Operation
(m1, m2, m3…mn) Accumulated mass:
Ma1, Ma2, ma3…man

Accumulated energy: Energy in gaseous products:


Ea1, Ea2, Ea3…Ean
Ep1, Ep2, Ep3…Epn

Input energy
Energy in solid wax:
(E1, E2, E3…En)
Ew1, Ew2, Ew3…Ewn

Energy losses:
EL1, EL2, EL3…ELn

Figure 5.1 modeling the energy and mass calculations


This open system governed by the law of conservation of matter and energy. Hence,
various material and energy inputs undergo conversions that lead to accumulations and

45
output. The mass and energy analysis mainly involve the transformation of mass (wax, and
gaseous) through cracking and burning liberating various energy forms, exhaust gases and
residue ash.
5.1.2. Mass Balance within the Process

The law conservation of mass or energy states that in every chemical and physical process,
matter can neither be created nor destroyed but can be transformed from one form (mass
or energy) to another (Eq. 5.1).
Q+ =0 (5.1)
Applying the non-flow conservation of energy law to the process involves an integrated of
physical and chemical changes sustained by net heat transformation (Q) involving internal
energy (U) and work (W) changes (Eq. 5.2).
2 2
U2 − 𝑈1 = 1 dQ + 1 dw (5.2)
Applying the law of conservation of mass using [Mi (mass in), Mo (mass out), Mg (mass
generated) and Ma (mass accumulated)] gives equation 5.3.
𝑀𝑖 − 𝑀0 + 𝑀𝑖 = Mg (5.3)
The application of this principle is necessary for quantifying solid.
5.2. Material Balance

From Formulated shoe polish (33 % of sachet wax, 15 % of Bee wax, 12 % of Fragrance,
and 50 % of Olive oil) was needed.
1. Cutting Mill
Assumption: - used water sachet was sufficiently dried
- From projected demand 700,000 kg/year was specified, 231,000 kg/year of used water
sachet, 105,000 kg/year of Bee wax, 84,000 kg/year of Fragrance, 350,000 kg/year of Olive
oil.

Cutting Mill

Used water sachet, 𝑚1 85% * 𝑚1 (proper 𝑠𝑖𝑧𝑒𝑑 used water


sachet) 231,000 kg/year 𝑚2 = 196,350 kg/year
15% 𝑚1 (𝑓𝑖𝑛𝑒used water sachet) =34,650 kg/year

Assumption: - 85% of proper used water sachet was obtained; the remaining 15% was
fined used water sachet.

46
𝑚2 = 0.85 *𝑚₁=0.85∗231,000 𝑘𝑔/year=196,350 𝑘𝑔/year
𝑚3 =0.15*𝑚₁=0.15∗12,000𝑘𝑔/𝑑𝑎𝑦= 34,650 𝑘𝑔/year

2. Carbonization unit

𝑚4 (Gases Co, Co2, Ch4, Sox, etc)


𝑚2 =196,350 Kg/year Furnace

𝑚5 Sachet wax (Polythene Wax)

In the lab scale, 100 g of used water sachet was pyrolyzed and 59 g of sachet wax was
obtained.
𝑚5 =196,350 Kg/year*59/100=115,846 Kg/year
And 𝑚𝑖𝑛 =𝑚𝑜𝑢𝑡 =𝑚4 =𝑚2 -𝑚5 =196,350 Kg/year- 115,846 Kg/year=80,503 Kg/year

3. Cooling unit

Cooling Tank
𝑚5 =80,503 kg/yea 𝑚6 =80,503 kg/year

4. Melting

Bee wax
Heater (Melting)
𝑚7 ==105,000 Kg/day
𝑚7=105,000 Kg/year
5. Soaking and Filtering
From lab result 100 g of bee wax was filtered 80 g of bee wax
𝑚8 == 105,000 Kg/year*80/100=84,000 kg/year

Soaking and
𝑚8 ==84,000 Kg/year
filtering
𝑚7 ==105,000 Kg/year

47
6. Mixing Reactor
𝑚10= = 84,000 of fragrance olive oil
𝑚9 =350,000 Kg/year

Sachet wax 𝑚5 =80,503 Kg/year


Mixing Reactor

Bee wax 𝑚8 =84,000 Kg/year Shoe polish


𝑚11 =2,333 Kg/day

7. Cooling
𝑚11 =2,333 Kg/day Cooling Tank
Black Shoe polish
𝑚12 =2,333 =700 Ton /year

5.3. Energy Balance Calculation

The reactor is designed with a used water sachet flow rate of 5,000 k𝑔/ℎ. The nitrogen (N₂)
flow rate inside the reactor is determined by Carbolite characteristics. The N₂ gas velocity
required for 2mm particles inside the horizontal tubular reactor is in the region of 0.3m/s
(Yanik et al. 2007). Assuming a maximum linear velocity flow was taken as 5 kg/h to
increase the robustness of the design. For practical operation the N₂ flow rate should be in
the region of 2 – 3 kg/h.

The energy balance of the system can be viewed as the separate combination of N₂ gas and
used water sachet and pyrolysis products. N₂ gas does not undergo phase change or
reaction and it therefore requires heating and cooling to the design temperatures. Used
water sachet requires heating, and then undergoes a reaction resulting in phase change.
The pyrolysis product requires cooling and condensation.

48
mS mg (𝑁2, ,CO,𝐶𝑂2 ,𝑆𝑂𝑥 ,𝑁𝑂𝑥 )
mN Pyrolytic reactor

msw

Qin
𝑄𝑜𝑢𝑡
Where𝑚s = mass flow rate of used water sachet;𝑚𝑔 = 𝑚𝑎𝑠𝑠𝑓𝑙𝑜𝑤𝑟𝑎𝑡𝑒𝑠𝑜𝑓𝑔𝑎𝑠𝑒𝑠; 𝑚𝑠𝑤 = mass
flow rate sachet wax; 𝑚𝑁 = mass flow rate of nitrogen

Eout = E in + E generated –E consumed-E accumulated + E losses (5.4)

At steady state the accumulation of energy is zero. Pyrolysis heat requirements between
200 and 400 J/g were reported for various biomasses by Van de Velden et al. (2010).
Therefore at a used water sachet flow rate of 463 g/s approximately 138.9 KJ/s could be
required. During pyrolysis energy is required in the form of heat, to create the reactive
conditions.

5.3.1. Thermodynamic properties for the energy balance

The enthalpy of evaporation and specific heat capacity for water and nitrogen were
obtained from Cengel (2003). The bio-gas specific heat capacity was estimated from CO and
CO2 be close to 1 kJ/kg*K (www.engineeringtoolbox.com, 2009). To account for variation
and increase the robustness of the design the value was slightly increased to (1.5 kJ/kg*K).
Average Cp values were used over the temperature range 25 – 500°C.

From the references for thermodynamic properties are given:


Qin = ΔE=ΔEheating+ΔEevap+ΔErxn……………………………………………………………………...5.5
Table5.2 Energy balance on Carbolite reactor
Species M*kg/h Cp ( ave ),kJ/kg ∆𝑻, 𝒌 Q, kW
Biomass heating 5,000 1.2 475 791.7
Nitrogen heating 5 1.1 475 0.73
Total 792.43

5.4. Equipment Design and Selection

Equipment design for this preliminary process evaluation involves determining the size of
the equipment in terms of the volume, flow per unit time, or surface area. Some of the

49
calculations are presented in the following to indicate the extent of the calculations which
are sometimes adequate for a preliminary design.

5.4.1. Reactor Volume

Assume a 4-h cycle and operation of the mixing reactor at constant temperature and
pressure of 115°F and 1 atm, respectively. The volume of reactants per day (with a 10%
safety factor)
Equipment Sizing
Provide olive oil and sachet wax storage
Volume of sachet wax Tank = (3,982) * (6) = 23,892 gal
Volume of olive oil Tank= (4500) * (6) = 27,000 gal
Select a 24,000-gal carbon steel tank for sachet wax storage and a 27,000-gal carbon steel
tank for olive oil storage
5.4.2. Equipment specifications
Table 5.3 Equipment specification and sizing

NR Item & description Size Materials of


Construction
1 Storage tank For wax 24,000 gal Carbon steel

2 Storage tank for used water sachet 27,000 gal Carbon steel
3 Mixing reactor 1,300 gal Stainless steel
4 pump (centrifugal) for melted wax 70 psi (up to Carbon steel
transfer 50 psi)
5. pump (screw) for sachet 50 psi( up to Carbon steel
transfer 50 psi)

50
Chapter Six
6. Economical Feasibility Study
6.1. Plant Location & Site Location
The geographical location of the final plant can have strong influence on the success of the
industrial venture. Considerable care must be exercised in selecting the plant site, and
many different factors must be considered. Primarily the plant must be located where the
minimum cost of production and distribution can be obtained but other factors such as
room for expansion and safe living conditions for plant operation as well as the
surrounding community are also important. The location of the plant can also have a
crucial effect on the profitability of a project.
The choice of the final site should first be based on a complete survey of the advantages
and disadvantages of various geographical areas and ultimately, on the advantages and
disadvantages of the available real estate. The various principal factors that must be
considered while selecting a suitable plant site are briefly discussed in this section. The
factors to be considered are raw material availability, location (with respect to the
marketing area), availability of suitable land, transport facilities, availability of labors,
availability of utilities (Water, Electricity), environmental impact and effluent disposal,
local community considerations, climate, Political strategic considerations, taxations and
legal restrictions

a) Raw Materials Availability

The source of raw materials is one of the most important factors influencing the selection
of a plant site. This is particularly true for the shoe polish plant because a large volume of
used water sachet is consumed in the process, which will result in the reduction of the
transportation and storage charges. Attention should be given to the purchased price of the
raw materials, distance from the source of supply, freight and transportation expenses,
availability and reliability of supply, purity of raw materials and storage requirements.

b) Location

The location of markets or intermediate distribution centers affects the cost of product
distribution and time required for shipping. Proximity to the major markets is an important
consideration in the selection of the plant site, because the buyer usually finds
advantageous to purchase from near-by sources.

51
c) Transport

The transport of materials and products to and from plant will be an overriding
consideration in site selection. If practicable, a site should be selected so that it is close to at
least two major forms of transport: road, rail way. Road transport is being increasingly
used, and is suitable for local distribution from a central warehouse.
Rail transport will be cheaper for the long-distance transport. If possible the plant site
should have access to all three types of transportation. There is usually need for convenient
rail and air transportation facilities between the plant and the main company
headquarters, and the effective transportation facilities for the plant personnel are
necessary.

d) Availability of Labors

Labors will be needed for construction of the plant and its operation. Skilled construction
workers will usually be brought in from outside the site, but there should be an adequate
pool of unskilled labors available locally; and labors suitable for training to operate the
plant. Skilled tradesmen will be needed for plant maintenance. Local trade union customs
and restrictive practices will have to be considered when assessing the availability and
suitability of the labors for recruitment and training.

e) Availability of Utilities

The word “utilities” is generally used for the ancillary services needed in the operation of
any production process. These services will normally be supplied from a central facility and
includes Water, Fuel and Electricity.

f) Local Community Considerations

The proposed plant must fit in with and be acceptable to the local community. Full
consideration must be given to the safe location of the plant so that it does not impose a
significant additional risk to the community.

6.2. Market Study &Plant Capacity

6.2.1. Past Supply and Present Demand

The demand for polishes largely met through import. Ethiopia imported a variety of
polishes and creams used in different applications. The data source for import statistics i.e.

52
Ethiopian Revenue and Customs Authority classifies imported of polishes and creams
under the following headings.
34051000 – Polishes, creams and similar preparations for foot wear or leather;
34052000 – Polishes, creams and similar preparations for maintenance of wood work; and
34053000 –polishes, creams and similar preparations for coachwork
Among the above three types of polishes and creams imported during the period 2000-
2001 , only the first two types , which are intended for use in footwear and wood are
considered in the analysis of past supply and present demand . The quantity and value of
the two types of polishes and creams imported in the past 12 years covering the period
2000-2011 is presented in the Table 6.1
Table 6.1 past supply data of shoe polish

Year Amount of Shoe Polish [ Ton ] Cost in (000 ) Birr


2000 382.2 9776
2001 478.8 12,959
2002 393.7 10,825
2003 345 8,642
2004 473.4 12,495
2005 586.2 15,312
2006 587.5 19,159
2007 672.3 20,441
2008 661.1 23,482
2009 495 25,095
2010 568 37,991
2011 442.1 33,313
Source: - Ethiopian Revenues and Customs Authority.
Table 6.1 reveals that import of polishes and creams during the period 2000-2007/08 has
been modestly rising. The annual average level of import which was 400 tons during the
period 2000 – 2003 has increased to annual average of 580 tons during the years 2004-
2007/08. However, during the last recent three years i.e. 2009 – 2011 the mean figure has
slightly declined to about 540 tons. Hence, by looking to the historical data the present
demand is estimated at about 600 tons.

53
6.2.2. Projected Demand

The factors that affect the demand for shoe and floor polishes are urbanization and urban
population growth, and income rise of the urban population. Footwear and floors that
require polishing are basically found in the urban areas. Hence, an annual average growth
rate of 4% is taken in forecasting the future demand by linking with urbanization and
urban population growth (see Table 6.2).
Table 6.2 projected demand for polish (TONS)

Year Projected Demand of Shoe Polish [ Ton ]


2013 624
2014 649
2015 675
2016 702
2017 730
2018 759
2019 790
2020 821
2021 854
2022 888
2023 924

The product is a consumer item which is to be demanded by most people. Hence, the
product has to reach the final consumer through a two step channel i.e. distributors and
retailers.
6.3. Plant Capacity and Production Program
6.3.1. Plant Capacity

The market study shows that demand for shoe polish increases from 624 tons in the year
2013 to 924 tons in the year 2023. Based on the market study and period required to
implement the project and market penetration and technical skill development, the
envisaged plant capacity is 700 tons per annum on a single shifts of 8 hours per day and
300 working days per year.

54
6.4. Economical Estimation
6.4.1. Estimated Capital Costs For Shoe polish Production
Table 6.3 Purchased Equipment cost

Type of Equipment Quantity Equipment Cost ($ )


Cutting Mill 1 14,000
Screen 1 7,000
Elevator 1 6,500
Heater 1 70,000
Storage tank 3 220,000
Filter tank 1 63,000
Soaking tank 1 45,000
Packaging machine 1 86,000
Mixing reactor 1 120,000
Rotary Cooler 1 100,000
Centrifugal pump 1 2300
Screw pump 1 2,200

Total purchased equipment cost= Total processing equipment=1,448,000$

55
6.4.1.1Estimation of Total Capital Investment
Table.6.4. Estimation of FCI and TCI

Item Solid Processing Cost ( $ )


Plant
Purchased Equipment – Delivered 45 % 1,448,000

Purchased-equipment installation 45% 651,600

Instrumentation and controls 9% 130,320


(installed)
Piping (installed) 16% 231,680

Electrical(installed) 10% 144,800

Buildings(including services) 25% 362,000

Yard improvements 13% 188,240

Service facilities(installed 40% 5,79,200

Land 6% 86,880
Total direct plant cost 3,822,720

Engineering and Supervision 33 % 477,840

Construction expenses 39% 564,720

Indirect costs 1,042,560

Total direct and indirect plant costs …… 4,865,280

Contractor’s fee (about 5% of direct …… 243,264


and indirect
Contingency(about 10%(D+I) …… 486528

Fixed- capital investment …… 5,595,072

Working Capital ( About 15 % of TCI ) ……

56
Capital costsbased on different percentages of the total equipment cost according to Peters
and Timmerhaus (1991).
Total capital investment(𝑇𝐶𝐼) =𝐹𝐶𝐼 +𝑊𝐶 (6.1)
𝑊𝐶=15%∗𝑇𝐶𝐼 (6.2)
Insert Eq 6.2 in to Eq 6.1 we get,
𝑇𝐶𝐼=𝐹𝐶𝐼/0.85=5,595,072/0.85=6,582,438 $
6.4.2. Estimation of Total Product Cost
6.4.2.1. Estimation of Manufacturing Cost
Manufacturing Cost = Direct production cost + Fixed charges + Plant overhead cost.
a) Fixed Charges: (10-20% total product cost)
I. Depreciation: (depends on life period, salvage value and method of calculation-about
10% of FCI for machinery and equipment and 2-3% for Buildings) and Consider
depreciation = 10% of FCI for machinery and equipment and 2.5% for Building Value for
Buildings).
ii. Local Taxes: (1-4% of fixed capital investment) Consider the local taxes = 2.5% of fixed
capital investment.
iii. Insurances: (0.4-1% of fixed capital investment) Consider the Insurance
iv. Rent: (8-12% of value of rented land and buildings)
Total Fixed Charges= 𝐷𝑒𝑝𝑟𝑒𝑐𝑖𝑎𝑡𝑖𝑜𝑛+ 𝐿𝑜𝑐𝑎𝑙𝑇𝑎𝑥𝑒𝑠+ 𝐼𝑛𝑠𝑢𝑟𝑎𝑛𝑐𝑒𝑠 + 𝑅𝑒𝑛𝑡 =291,062.3$
b) Direct Production Cost: (about 60% of total product cost)
Now we have Fixed charges = 10-20% of total product cost – (given); Consider the Fixed
charges = 15% of total product cost.
Total product cost = Total fixed charges/0.15 𝑇𝑜𝑡𝑎𝑙𝑝𝑟𝑜𝑑𝑢𝑐𝑡𝑐𝑜𝑠𝑡
I. Raw Materials: (10-50% of total product cost); Consider the cost of raw materials = 30%
of total product cost 𝑅𝑎𝑤𝑚𝑎𝑡𝑒𝑟𝑖𝑎𝑙𝑐𝑜𝑠𝑡.
ii. Operating Labor (OL): (10-20% of total product cost); Consider the cost of operating
labor = 15% of total product cost.
iii. Direct Supervisory and Clerical Labor (DS & CL): (10-25% of OL); Consider the cost for
Direct supervisory and clerical labor = 17.5% * OL
iv. Utilities: (10-20% of total product cost); Consider the cost of Utilities = 15% of total
product cost
v. Maintenance and repairs (M & R): (2-10% of fixed capital investment);consider the
maintenance and repair cost = 6% of fixed capital investment.

57
vi. Operating Supplies: (10-20% of M & R or 0.5-1% of FCI); consider the cost of Operating
supplies = 15% of M &R.
vii. Laboratory Charges: (10-20% of OL); consider the Laboratory charges = 15% * OL
Laboratory charges = 15% ∗291,062.3$ $ = 43,659.3$
c) Plant overhead Costs
(50-70% of Operating labor, supervision, and maintenance or 5-15% of total product cost);
includes for the following: general plant upkeep and overhead, payroll overhead,
packaging, medical services, safety and protection, restaurants, recreation, salvage,
laboratories, and storage facilities.
Consider the plant overhead cost = 10% of Total Product Cost; 𝑃𝑙𝑎𝑛𝑡𝑜𝑣𝑒𝑟ℎ𝑒𝑎𝑑𝑐𝑜𝑠𝑡 = 10%
∗1,940,415.3$=194,041.5$
Thus, Manufacturing cost = Direct production cost + Fixed charges + Plant overhead costs
𝑀𝑎𝑛𝑢𝑓𝑎𝑐𝑡𝑢𝑟𝑒𝑐𝑜𝑠𝑡 = (1,644,884.3$) + (291,062.3$) + (194,041.5$) = 2,129,988.1$
6.4.2.2. Estimation of General Expenses Cost
General Expenses = Administrative costs + distribution and selling costs + research and
development costs.
I. Administrative costs :( 2-6% of total product cost);Consider the Administrative costs =
4% of total product cost.
ii. Distribution and Selling costs: (2-20% of total product cost); includes costs for sales
offices, salesmen, shipping, and advertising. Consider the Distribution and selling costs =
11% of total product cost 𝐷𝑖𝑠𝑡𝑟𝑖𝑏𝑢𝑡𝑖𝑜𝑛𝑎𝑛𝑑𝑠𝑒𝑙𝑙𝑖𝑛𝑔𝑐𝑜𝑠𝑡𝑠
iii. Research and Development costs: (about 5% of total product cost)
Consider the Research and development costs = 5% of total product cost
𝑅𝑒𝑠𝑒𝑎𝑟𝑐ℎ𝑎𝑛𝑑financing (interest): (0-10% of total capital investment), Thus, Total General
Expenses = 717,204.9$.
Total Product cost = Manufacture cost + General Expenses
Total Product cost = (2,129,988.1$) + (717,204.9$) = 2,847,193$
6.4.3 .Production Program
In order to develop the operators’ skill in production and quality control, it is vital to have a
gradual capacity buildup. In addition to this, a period is required to penetrate to the
market. Hence, it is assumed that the plant will go into full capacity operation in four years’
time starting with 70% capacity in the first year and progressively developing to 85%, 95%
and 100% in the second, third and fourth year and then after, respectively. The production
program of the envisaged plant is given in Table 6.5.

58
Table 6.5 Production Program

No. Item Description 𝟏𝐬𝐭 year 𝟐𝐧𝐝 year 𝟑𝐫𝐝 year 4th-𝟔𝐬𝐭𝐡
1 Shoe polish ( tons) 490 550 660 700
2 Capacity 70 85 95 100
Utilization

6.4.4. Financial Evaluation


6.4.4.1. Profitability

Based on the projected profit, the project will generate a profit throughout its operation
life. Annual net profit after tax ranges from Birr 4.75 million to Birr 5.99 million during the
life of the project. Moreover, at the end of the project life the accumulated net cash flow
amounts to Birr 60.27 million.

6.4.4.2. Break-even Analysis

The break-even analysis establishes a relationship between operation costs and revenues.
It indicates the level at which costs and revenue are in equilibrium. To this end, the break-
even point for capacity utilization and sales value estimated by using income statement
projection are computed as followed.

𝐵𝐸𝐶= [𝐹/ (𝑇𝑆𝑅−𝑇𝑃𝐶)]∗100 (6.3)

Fixed Cost+Financial Cost


Break -Even Sales Value= (6.4)
Variable Margin ratio (%)

Break -Even Sales Value= 26,583,480 birr

Break –Even Point=30 % (6.5)

6.4.4.3. Pay-back Period

Payback period =𝐹𝐶𝐼/𝑁𝑒𝑡𝑐𝑎𝑠ℎ𝑎𝑐𝑐𝑟𝑢𝑎𝑙 (6.6)

The pay- back period, also called pay – off period is defined as the period required for
recovering the original investment outlay through the accumulated net cash flows earned
by the project. Accordingly, based on the projected cash flow it is estimated that the
project’s initial investment will be fully recovered within 3 years.

59
6.4.4.4. Internal Rate of Return
The internal rate of return (IRR) is the annualized effective compounded return rate that
can be earned on the invested capital, i.e., the yield on the investment. Put another way, the
internal rate of return for an investment is the discount rate that makes the net present
value of the investment's income stream total to zero. It is an indicator of the efficiency or
quality of an investment. A project is a good investment proposition if its IRR is greater
than the rate of return. That could be earned by alternate investments or putting the
money in a bank account. Accordingly, the IRR of this project is computed to be 30.37%
indicating the viability of the project.
𝑅𝑎𝑡𝑒𝑜𝑓𝐼𝑛𝑣𝑒𝑠𝑡𝑚𝑒𝑛𝑡 (𝑅𝑂𝐼𝑜𝑟𝑅𝑂𝑅) = 𝑁𝑒𝑡𝑃𝑟𝑜𝑓𝑖𝑡/𝑇𝐶I (6.7)
ROR= 30.5 %

6.4.4.5. Net Present Value


Net present value (NPV) is defined as the total present (discounted) value of a time series
of cash flows. NPV aggregates cash flows that occur during different periods of time during
the life of a project in to a common measuring unit i.e. present value. It is a standard
method for using the time value of money to appraise long-term projects. NPV is an
indicator of how much value an investment or project adds to the capital invested. In
principle, a project is accepted if the NPV is non-negative.
Accordingly, the net present value of the project at 10% discount rate is found to be Birr
25.90 million which is acceptable.
6.5. Economic & Social Benefits
The project can create employment for 30 persons. The project will generate Birr 16.44
million in terms of tax revenue. The establishment of such factory will have a foreign
exchange saving effect to the country by substituting the current imports. The project will
also generate income for the Government in terms of payroll tax.

60
Chapter Seven
7. Conclusion & Recommendation
Used water sachets have become uncontrollable nuisance in Ethiopia. Most places are
littered with the polymer made materials which are continuously dumped indiscriminately.
In fact a considerable portion of the Ethiopia land mass has been occupied by varieties of
waste. This research work thesis tends to look at the used water sachets as blessing by
converting them to a more useful product. The effective management of the polyethylene
waste through conversion into further usable products turns the littered surrounding to an
environmentally friendly one by preventing outspread of disease and simultaneously
creating employment for both skilled and unskilled labor.

Polyethylene wax was found to form a good and compatible formula in the production of
shoe polish. Its shoe polish exhibited soft texture, dark hue, and very good wrinkle
resistance compared with commercial shoe polish.
The use of polythene wax in the Production shoe polish was hereby recommended as it was
reduce extensively, the level of pollution, which arises as a result of indiscriminate disposal
of “used water sachet” in our environment.

The properties of Shoe Polish formulated from wax produced from used water sachet were
studied. Pyrolysis temperatures between 100˚C -200˚C is required to produced sachet wax
from used water sachets for formulated shoe polish. The melting point, density and
viscosity of one of shoe polish formulated using 33% sachet wax compared favorably with
standard commercial polish. One of the economic advantages of this research thesis work
was the use of 33 % sachet wax which was a waste product, in addition to bee wax to
produce the shoe polish. The other economic advantage of this project is that wealth
generation and employment opportunity can be created.

The conversion of low density polyethylene i.e. LDPE (used water sachet) was
demonstrated in this research. Efforts will be conduct in converting other polyethylene
such as ;ultra high molecular weight polyethylene (UHMWP),ultra low molecular weight
polyethylene (ULMWPE or PE-WAX),High molecular weight polyethylene (HMWPE),high
density polyethylene(HDPE),high density cross- linked polyethylene (HDXLPE),cross-
linked polyethylene (PEX or XLPE),medium density polyethylene (MDPE),linear low
density polyethylene (LLDPE), and ,Very low density polyethylene (VLDPE) to polyethylene
wax for further conversion into further usable products.

61
References
Ababio, O.Y (1990) “New School Chemistry” 3rd Edition. African FEP. Publishers, Nigeria pp
108-113.
Aboulkas et al (2007) Pyrolysis kinetics of polypropylene Morocco oil shale and their
mixture. Journal of thermal analysis and calorimetry, 89: 203-209.
Achankeng E (2003) Globalization, urbanization and municipal solid waste management in
Africa. African studies association of Australasia and the pacific 2003 conference
proceedings.
Akpovi, S. V ;( 1993) Provision of environmental sanitation: The problem of refuse disposal
in Benin City. Paper presented at the CENCER seminar series, university of Benin, Benin
City (1981).
Angyal A, Miskolczi N, Bartha L (2007) Petrochemical feedstock by cracking of plastic
waste. Journal of analytical and applied pyrolysis, vol. 79, Issues 1-2: 409-414 [Pyrolysis
2006: Papers presented at the 17th international symposium on analytical & applied
pyrolysis, Budapest, Hungary].
Aquado J, Serrano, DP, Escola JM (2006) Catalytic upgrading of plastic wastes: In: Scheirs J,
Kaminsky W (Eds), Feedstock recycling and pyrolysis of waste plastics: Converting waste
plastics into diesel and other fuels, John Wiley & Sons, Ltd, UK.
Aziegbe, F.I ;( 2004) Sediment sources, redistribution and management in Ekpoma, Edo
State, Nigeria Journal of Human Ecology (in press).
Bayer, A.G. (1986) “Tanning, Dyeing and Finishing” 4th Edition GeschaftbereichFarben,
5090 Leverrkusenpp 24-30.
Berger, P.S, Clark, R.M and Reasoner D.J ;( 1993). Water, Drinking. In: Encyclopedia of
Microbiology. Vol. 4:385-398.
Bhandare PS, Lee BK, Krishman K (1997) Study of pyrolysis and incineration of disposable
plastics using combined TG/FT-IR technique. Journal of thermal analysis, vol. 49: 361-366.
Akademiai Kladó. Budapest.
Biniecka M, Campana P, Tarola AM (2005) Thermo-valorisation integrated waste
management. XI Italian Hungarian Symposium on Spectrochemistry, MicrochemicalJournal,
vol. 79, issues 1-2: 319-324.
Blasi DC (1997) Linear pyrolysis of cellulosic and plastic waste. J. of Analytical and Applied
pyrolysis. Vol. 40-41:463-479, pyrolysis ‟96.
Blazsó M (1997) Recent trends in analytical and applied pyrolysis of polymers. Journal of
analytical and applied pyrolysis, 39: 1-25.

62
Bockhorn H et al. (1999) Dehydrochlorination of plastic mixtures. Journal of analytical and
applied pyrolysis, 49: 97-106.
Boer DE, Boer DJ & Jager J (Eds) (2005) Waste management planning and optimisation:
Handbook for municipal waste prognosis and sustainability assessment of waste
management systems, Ibidem-verlag, Stuttgart.
Bos U, Makishi C, Fischer M (2007) Life cycle assessment of common used agricultural
plastic products in the EU (abstract), ISHS Acta Horticulturae 801: International
Symposium on High Technology for Greenhouse System Management: Greensys2007.
Characklis, W.G, and Marshall K.S ;( 1990). Biofilms: a basis for an interdisciplinary
approach. pp. 3-15.
Cheremisinoff NP (2003) Handbook of solid waste management and waste minimisation
technologies. Butterworth Heinemann, New York.
Christie R.M (1993) “Surface Coating Reviews in Pigment Structures, Properties and
Synthesis Procedure” Oil and Color Chemist Association, U.K P 10-11.
Costa PA, Pinto FJ, Ramos AM, Gulyurtlu IK, Cabrita IA, Bernardo MS (2007) Kinetic
Evaluation of the Pyrolysis of Polyethylene Waste, Energy & Fuels 21: 2489-249.
Edraw max Software
Egwari, L., Aboaba, O; (2002). Environmental impact on the bacteriological quality of
domestic water supplies in Lagos, Nigeria.Rev. SaúdePública. 36 (4): 513-520.
Encinar M, González JF (2008) Pyrolysis of synthetic polymers and plastic wastes. Kinetic
study. Fuel Processing Technology, Vol. 89, issue 7: 678-686.
Ferrara I, Missios P (2005) Recycling and waste diversion effectiveness: Evidence from
Canada. Environmental & Resource Economics, 30: 221-238.
Foley G, Kerkhof P, Madougou D (2002) A review of the rural firewood market strategy in
West Africa. Africa region working paper series, No. 35.
Gadgil, A., Derby, E., (2003). Providing Safe Drinking Water to 1.1 Billion Unserved People.
Paper # 70492.
http://www.academia.com
http://www.academia.com
http://www.aiche.com
J.H De Bussy:"Materials and Technology -Natural Organic Materials Related Synthetic
Products ". Longman, London, UK, vol. v, pp 317-381, 1976.
L .Jixing Shuyuan, Xuan Wang and L Xian yang. Study on the Conversion Technology of
waste Polyethylene Plastic to Polyethylene Wax, Energy Sources vol 25, pp 77 -83. 2003.

63
L. Chalmers,” Household and Industrial Chemical pecialties ". Chemical Publishing Co. Inc.,
New York, NY, USA, 1979.
LeChevallier, M.W; (1999). Biofilms in drinking water distribution systems: significance
and control, identifying future drinking water contaminants. National Academy Press.
Washington, DC.
Mustapha, S., Adam, E.A., (1991). Discussion on Water Problems in Nigeria: Focus on
Bauchi State. Natl. Water Res. Inst.
Odemerho (Eds.). Ibadan, Evans Brothers Publishing Company Limited P 77-87
Onokerhoraye, A. G ;( 1984) Perspectives on the urban environmental quality and public
policy in Nigeria. Paper presented at the Department Seminar Series, Department of
Geography and Regional Planning, University of Benin, Benin City.
Omuta, G. E. D ;( 1988) urban solid waste generation and management: Towards an
environmental sanitation policy. In: Environmental Issues and Management in Nigeria
Development. P. O. Sada and F. O.
Owolabi, R.U., Kareem, S.A., (2010) Dechlorination/On set of microbial growth in water
storage tank, Journal of Applied Sciences Research, 6(6): 589-593.
Oyinlade, O. O ;(1991)Urban Solid Waste Management in Nigeria: Case Study of Akure,
Ondo State: Unpublished M.Sc. Thesis, Department of Geography and Regional Planning,
University of Benin,Benin City.
Peters, M., and Timmerhaus, K., 1991. Plant Design and Economics for Chemical Engineers.
McGraw-Hill, Inc., New York.
R.H. Perry; and C.H Chilton,” Chemical Engineers Handbook ", McGraw-Hill, New York, NY,
USA, 2008.
Ramasastry, C. V ;( 1988) Estimation of solid wastes in Bendel State Nigeria. In:
Environmental Issues and Management in Nigeria Development. P. O. Sada and F. O.
Odemerho (Eds.). Ibadan, Evans Brothers Publishing Company Limited.
Secchi, A.R., Bolson, A., (2005), Analysis and Optimization OfLDPE Production.
US EPA ;( 2002) Health Risks from Microbial Growth and Biofilms in Drinking Water
Distribution Systems.
Van der Wende, E., and Characklis,W.G (1990). Biofilms in potable water distribution
systems. p. Drinking Water Microbiology.McFeters,GA (Ed.). pp. 249-268. Springer-Verlag.
New York, NY.

64
Appendices
Financial Analysis Supporting Tables
Appendix I: Income Statement (in 000 Birr)
Item Year 2 Year 3 Year 4 Year 5 Year 6 Year 7 Year 8 Year 9 Year 10 Year 11
Sales 60,129 63,294 63,294 63,294 63,294 63,294 63,294 63,294
revenue 44,306 53,800
Less variable 38,060 46,216 51,653 54,371 54,371 54,371 54,371 54,371 54,371 54,371
costs
VARIABLE 6,246 7,584 8,476 8,923 8,923 8,923 8,923 8,923 8,923 8,923
MARGIN
in % of sales 14.10 14.10 14.10 14.10 14.10 14.10 14.10 14.10 14.10 14.10
revenue
Less fixed 1,079 1,079 1,079 1,079 1,079 1,079 1,079 1,079 1,079 1,079
costs
OPERATION 5,167 6,506 7,398 7,844 7,837 8,561 8,561 8,561 8,561 8,561
AL MARGIN
in % of sales 11.66 12.09 12.30 12.39 12.38 13.53 13.53 13.53 13.53 13.53
revenue
in % of sales 1,408 1,232 1,056 880 704 528 352 176 0
revenue
GROSS 5,167 5,097 6,165 6,788 6,957 7,857 8,033 8,209 8,385 8,561
PROFIT
in % of sales 11.66 9.47 10.25 10.72 10.99 12.41 12.69 12.97 13.25 13.25
revenue
Income 0 0 0 2,036 2,087 2,357 2,410 2,463 2,568
(corporate)
tax 2,515
NET PROFIT 5,167 5,097 6,165 4,751 4,870 5,500 5,623 5,746 5,869 5,992
in % of sales 11.66 9.47 10.25 7.51 7.69 8.69 8.88 9.08 9.27 9.47
revenue

65
Appendix II: Cash Flow for Financial Management

Item Year 1 Year 2 Year 3 Year 4 Year 5 Year 6 Year 7 Year 10 Year 11
Total Cash
Flow 5,889 58,021 53,807 60,134 63,294 63,294 63,294 63,294 63,294

Inflow funds 5,889 13,715 7 5 0 0 0 0 0


Inflow
operation 0 44,306 53,800 60,129 63,294 63,294 63,294 63,294 63,294
Other income 0 0 0 0 0 0 0 0 0
TOTAL CASH
OUTFLOW 5,889 52,025 52,295 56,669 60,361 59,357 59,450 59,080 57,197
Increase in
fixed assets 5,889 0 0 0 0 0 0 0 0
Increase in
current assets 0 12,435 2,660 1,773 887 1 0 0 0
Operating costs 0 38,060 46,216 51,653 54,371 54,378 54,378 54,378 54,378
Marketing and
Distribution
cost 0 250 250 250 250 250 250 250 250
Income tax 0 0 0 0 2,036 2,087 2,357 2,515 2,568
Financial costs 0 1,280 1,408 1,232 1,056 880 704 176 0
Loan
repayment 0 0 1,761 1,761 1,761 1,761 1,761 1,761 0
SURPLUS
(DEFICIT) 0 5,996 1,512 3,464 2,933 3,937 3,844 4,214 6,097
CUMULATIVE
CASH
BALANCE 0 5,996 7,508 10,973 13,905 17,842 21,687 33,958 40,056

66
Appendix I I I: Discounted Cash Flow (in 000 Birr)
Item Year 1 Year 2 Year 3 Year 4 Year 5 Year 6 Year 7 Year 8 Year 9 Year 10

Total Cash
Inflow 0 44,306 53,800 60,129 63,294 63,294 63,294 63,294 63,294 63,294
Inflow
operation 0 44,306 53,800 60,129 63,294 63,294 63,294 63,294 63,294 63,294

Other income 0 0 0 0 0 0 0 0 0 0
Total Cash Out 56,65
Flow 18,291 40,963 48,235 52,787 8 56,715 56,985 57,038 57,144 57,197
Increase in fixed
assets 5,889 0 0 0 0 0 0 0 0 0
Increase in net
working capital 12,402 2,653 1,769 884 1 0 0 0 0 0

Operating costs 0 38,060 46,216 51,653 54,371 54,378 54,378 54,378 54,378 54,378
Marketing and
Distribution
cost 0 250 250 250 250 250 250 250 250 250
Income
(corporate) tax 0 0 0 2,036 2,087 2,357 2,410 2,515 2,568
NET CASH
FLOW -18,291 3,343 5,565 7,342 6,636 6,579 6,309 6,256 6,150 6,097
-
CUMULATIVE
NET CASH
FLOW -18,291 14,948 -9,383 -2,041 4,594 11,173 17,482 23,738 36,091 42,189
Net present
value -18,291 3,039 4,600 5,516 4,532 4,085 3,561 3,210 2,608 2,351
Cumulative net -
present value -18,291 15,252 -10,653 -5,137 -604 3,480 7,041 10,252 15,754 18,105

Net Present Value = 25,897


Rate of Return = 30.7 %
Pay Back Period = 3 years

67
Appendix IV: Pictures of Plastic disposal and Laboratory Equipments

A: Dominance of plastic waste in landfills and impacts on the environment

B: Basic Equipments used to produce shoe polish

68
C: Shoe Polish Product from Bee wax and Used Water Sachets

69
i

You might also like