1020 PDF

1020 GRAIN HEADER (S/N JJC0215001 TO JJC0227000)
1-01 1020 GRAIN HEADER, P.I.N. JJC0215001 - JJC0227000, PARTS CATALOG

1-01 1020 GRAIN HEADER, P.I.N. JJC0215001 - JJC0227000, PARTS CATALOG
Ссылка Номер детали Кол-во Описание

1-02 LOCATION OF SERIAL AND PRODUCT IDENTIFICATION NUMBERS
1-02 LOCATION OF SERIAL AND PRODUCT IDENTIFICATION NUMBERS

1-08 PICTORIAL INDEX, REEL DRIVE HYDRAULIC SYSTEM
1-08 PICTORIAL INDEX, REEL DRIVE HYDRAULIC SYSTEM

1 Reel Drive Hose (Page 8-2)
2 Reel Drive Cross Tube (Page 8-2)
3 Reel Drive To Combine Hose (Page 8-2)
4 Male Coupling (Page 8-2)
5 Female Coupling (Page 8-2)
1-10 PICTORIAL INDEX, REEL LIFT HYDRAULICS
1-10 PICTORIAL INDEX, REEL LIFT HYDRAULICS

1 Reel Lift Master Cylinder Hose (Pages 8-8, 8-10)
2 Reel Lift Slave Cylinder Hose (Pages 8-8, 8-10)
3 Cylinder to Cylinder Cross Tube (Pages 8-8, 8-10)
4 Master Cylinder Cross Tube (Pages 8-8, 8-10)
5 Reel Lift to Combine Hose (Pages 8-8, 8-10)
6 Male Coupling (Pages 8-8, 8-10)
1-12 PICTORIAL INDEX, REEL FORE AND AFT ADJUSTMENT HYDRAULIC SYSTEM
1-12 PICTORIAL INDEX, REEL FORE AND AFT ADJUSTMENT HYDRAULIC SYSTEM

1 Reel Adjustment Cylinder Hose (Pages 8-4, 8-6)
2 Right Adjustment Cylinder Cross Tube (Pages 8-4, 8-6)
3 Cylinder to Cylinder Cross Tubes (Pages 8-4, 8-6)
4 Left Adjustment Cylinder Cross Tube (Pages 8-4, 8-6)
5 Reel Adjustment to Combine Hose (Pages 8-4, 8-6)
6 Male Coupling (Pages 8-4, 8-6)
7 Female Coupling (Pages 8-4, 8-6)
4-02 WIRING HARNESS AND LAMP MOUNTING
If dealer is looking for harness for flashing warning lights for 1000 series headers, see pm -3490. P/n B93448 is for 1010 and 1020 light
kits, and p/n B93476 is for 1000 series (8 row wide). P/n for 1600 series is B93450. The p/n for harness only for 1600 series is
197077a1.
4-02 WIRING HARNESS AND LAMP MOUNTING

1 REF 2 LIGHT ASSEMBLY - warning, See Figure 4-04, Includes: Ref. 2 - 4
2 495-11053 2 WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
3 80679 2 Washer, Lock, 1/2"
4 425-118 2 NUT - hex, 1/2 inch NF
5 126890A1 2 SHIELD - marker light
6 409-7512 4 BOLT - hex serrated flange, 5/16 NC x 3/4 inch
7 231-5145 4 NUT - hex serrated flange, 5/16 inch NC
8 127031A1 2 SUPPORT - marker light
9 256873 2 BOLT - hex serrated flange, 5/16 NC x 1/2 inch
11 127057A1 2 ANGLE - marker light
12 140374A1 2 U-BOLT - support mounting
13 231-4215 4 NUT - hex, self-locking, 5/16 inch NC
15 231-5146 4 NUT, Flg, USR, 3/8"-16
16 128896A1 1 HARNESS - lamp, marker lights
17 362120R1 2 CLAMP - P-type, harness
18 702093C1 2 STRAP - tie, nylon retaining
If dealer is looking for harness for flashing warning lights for 1000 series headers, see pm -3490. P/n B93448 is for 1010 and 1020 light
kits, and p/n B93476 is for 1000 series (8 row wide). P/n for 1600 series is B93450. The p/n for harness only for 1600 series is
197077a1.
4-04 MARKER LIGHT
4-04 MARKER LIGHT

134454A1 2 LAMP ASSEMBLY - warning, Includes: Ref. 1 - 10
1 NSS 1 BODY - lamp
2 A41264 1 BULB, #1156, 12V, Lamp
3 A43731 2 GASKET - sealing, lens
A44202 1 KIT - lens, Includes: Ref. 6 & 7
6 NSS 2 LENS - lamp, amber
7 187-1083 8 SCREW - self-tapping, round head Phillips, No. 8 NC x 5/8 inch
8 495-11053 1 WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
9 80679 1 Washer, Lock, 1/2"
10 425-118 1 NUT - hex, 1/2 inch NF
8-02 REEL DRIVE MOTOR SYSTEM
8-02 REEL DRIVE MOTOR SYSTEM

1 REF 1 MOTOR ASSEMBLY - hydraulic, reel drive, See Figure 8-12
2 237-6010 4 O-RING, 10-1, 90 Duro, .755" ID x .097" Thk
4 218-5230 4 ELBOW - 90 degree, 3/4-16 inch flare x swivel
5 131057A1 2 HOSE - 1270 mm (50 inch) long, hydraulic, 3/8 ID (Pick-up reel)
6 L18337 2 STRAP - tie, 15 inch, nylon
8 1338406C1 2 TUBE - reel drive
9 1301178C1 UAR CLAMP - tube
10 1326572C1 UAR SPACER - 10 mm
11 1338408C1 2 TUBE - reel drive (15.0 foot)
13 413-432 UAR BOLT - hex, 1/4 NC x 2 inch
14 231-5344 UAR NUT - hex flange, self-locking, 1/4 inch NC
15 218-674 1 ADAPTER - straight, 3/4-16 inch flare x bulkhead flare
16 218-1255 1 NUT, LOCK, Blkhd, 3/4"-16
17 1316779C1 1 ANGLE - quick disconnect support
18 281-14812 2 SCREW - self-tapping, hex washer head, 5/16 NC x 3/4 inch
19 1321398C1 1 CLAMP - quick disconnect
23 413-48 2 BOLT - hex, 1/4 NC x 1/2 inch
24 218-5060 2 ADAPTER - straight, 3/4-16 flare x 7/8-14 inch O-ring boss
25 1282338C91 1 COUPLING - self-sealing female, 7/8-14 inch
26 1954133C1 1 PLUG - coupling, dust
28 1316829C1 1 HOSE - 965 mm (38 inch) long, hydraulic, 3/8 ID
29 1345266C1 1 WASHER - lock, white, special
30 1272399C2 1 COUPLER - self sealing, male, 7/8 inch NF
32 218-5146 2 ELBOW - 45 degree, 3/4-16 flare x 7/8-14 inch adj O-ring
35 413-828 2 BOLT - hex, 1/2 NC x 1-3/4 inch, if used
36 396-21053 2 WASHER - flat, 17/32 x 1-1/16 x 1/8 inch, hardened
37 231-5144 2 NUT, Flg, USR, 1/4"-20
8-04 REEL FORE AND AFT HYDRAULIC SYSTEM, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER

1 REF 2 CYLINDER ASSEMBLY - fore and aft, See Figure 8-14
2 218-5105 4 ELBOW - 90 degree, 9/16-18 inch flare x adj O-ring boss
5 183825C1 4 CLAMP - tube retaining
7 231-5344 4 NUT - hex flange, self-locking, 1/4 inch NC
10 141425A1 1 HOSE - 1448 mm (57 inch) long, hydraulic, 1/4 ID
15 1338414C1 1 TUBE - fore and aft (15.0 foot)
16 1338420C1 1 TUBE - fore and aft
17 138333A1 1 TUBE - fore and aft (15.0 foot)
19 1338418C1 1 TUBE - fore and aft (15.0 and 17.5 foot)
21 218-5354 2 FITTING, 9/16"-18, 37° x 7/8"-14, O-Ring
23 218-1254 1 NUT - hex, lock, bulkhead, 9/16 inch NF
25 413-448 4 BOLT - hex, 1/4 NC x 3 inch
26 1326573C1 4 SPACER - 45 mm long
27 702093C1 2 STRAP - tie, nylon
36 413-48 2 BOLT - hex, 1/4 NC x 1/2 inch
38 1541792C1 1 WASHER - lock, red, special
41 231-5144 2 NUT, Flg, USR, 1/4"-20
45 485093C1 2 CLAMP - double, hose
46 495-21031 2 WASHER - flat, 5/16 x 3/4 x 1/16 inch
47 413-440 2 BOLT - hex, 1/4 NC x 2-1/2 inch

3 237-6006 4 O-Ring, 6-1, 90 Duro, .468" ID x .078" Thk
8-06 REEL FORE AND AFT HYDRAULIC SYSTEM, 22.5, 25.0 AND 30.0 FOOT HEADER
8-06 REEL FORE AND AFT HYDRAULIC SYSTEM, 22.5, 25.0 AND 30.0 FOOT HEADER

1 REF 2 CYLINDER ASSEMBLY - fore and aft, See Figure 8-14
9 147876C1 1 HOSE - 1143 mm (45 inch) long, hydraulic 1/4 ID
10 141425A1 1 HOSE - 1448 mm (57 inch) long, hydraulic 1/4 ID
15 1316598C1 1 TUBE - center (22.5 and 25.0 foot)
15 1338421C1 1 TUBE - center (30.0 foot)
17 1338420C1 1 TUBE - fore and aft (30.0 foot), longer tube
17A 1338414C1 1 TUBE - fore and aft (30.0 foot), shorter tube, used with 1338420C1
20 218-673 1 ADAPTER - straight, 9/16-18 flare x bulkhead flare
21 218-5354 2 FITTING, 9/16"-18, 37° x 7/8"-14, O-Ring
25 413-448 6 BOLT - hex, 1/4 NC x 3 inch
26 1326573C1 6 SPACER - 45 mm long
27 702093C1 2 STRAP - tie, nylon
36 413-48 2 BOLT - hex, 1/4 NC x 1/2 inch
41 231-5144 2 NUT, Flg, USR, 1/4"-20
47 413-440 2 BOLT - hex, 1/4 NC x 2-1/2 inch
8-08 REEL LIFT HYDRAULIC SYSTEM, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER
8-08 REEL LIFT HYDRAULIC SYSTEM, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER

1 REF 1 CYLINDER ASSEMBLY - lift, master, See Figure 8-16
2 REF 1 CYLINDER ASSEMBLY - lift, slave, See Figure 8-18
9 183821C1 1 CLAMP - tube retaining, single
10 183825C1 3 CLAMP - tube retaining, double
12 413-428 4 BOLT - hex, 1/4 NC x 1-3/4 inch
13 1326572C1 4 SPACER - 10 mm, long
16 515-23206 1 CLAMP - single, hose
18 154273C1 2 BOLT - hex, self-locking, special, 3/8 NC x 1 inch
19 231-5146 2 NUT, Flg, USR, 3/8"-16
20 1338418C1 1 TUBE - reel lift (15.0 and 17.5 foot)
21 1316601C1 1 TUBE - reel lift (15.0 foot)
23 1338419C1 1 TUBE - reel lift
25 1541804C1 1 WASHER - black, special
26 218-5354 1 FITTING, 9/16"-18, 37° x 7/8"-14, O-Ring
8-10 REEL LIFT HYDRAULIC SYSTEM, 22.5, 25.0 AND 30.0 FOOT HEADER
8-10 REEL LIFT HYDRAULIC SYSTEM, 22.5, 25.0 AND 30.0 FOOT HEADER

9 183821C1 2 CLAMP - tube retaining, single
10 183825C1 4 CLAMP - tube retaining, double
12 413-428 6 BOLT - hex, 1/4 NC x 1-3/4 inch
13 1326572C1 6 SPACER - 10 mm, long
16 515-23206 1 CLAMP - single, hose
19 231-5146 2 NUT, Flg, USR, 3/8"-16
24 1338419C1 1 TUBE - reel lift
25 1541804C1 1 WASHER - black, special
26 218-5354 1 FITTING, 9/16"-18, 37° x 7/8"-14, O-Ring
8-12 REEL DRIVE MOTOR
8-12 REEL DRIVE MOTOR

1 130409A1 1 MOTOR ASSEMBLY - reel drive, Includes: Ref. 2 - 18
2 NSS 1 HOUSING - motor
3 NSS 1 COVER - drive end
4 NSS 1 SEAL - oil
5 NSS 1 WASHER - special
6 NSS 1 SEAL - oil
7 NSS 1 RING - sealing
8 NSS 1 SHAFT ASSEMBLY - drive
9 NSS 1 BEARING - thrust
10 NSS 1 SPACER - thrust bearing
11 126-124 1 Woodruff Key, #15, 1/4" x 1", HT
12 NSS 3 RING - sealing
13 NSS 1 LINK - drive
14 NSS 1 PLATE - manifold
15 NSS 1 ROTOR ASSEMBLY - motor
16 NSS 1 COVER - end
17 NSS 7 BOLT - cover
18 NSS 4 BOLT - cover
188118A1 1 KIT - seal
8-14 REEL FORE AND AFT CYLINDER
8-14 REEL FORE AND AFT CYLINDER

1282012C93 2 CYLINDER ASSEMBLY - 32 (1-1/2) ID x 330 mm (13 inch) stroke, hydraulic, fore and aft, Includes:
Ref. 1 - 17
1 NSS 1 BODY - cylinder
2 232-4617 1 NUT, LOCK, 7/16"-20, GC
3 1282016C1 1 ROD - piston
4 1282017C2 1 PISTON - cylinder
5 108996C1 1 GLAND - cylinder, front
62240C92 1 KIT - seal, cylinder, Includes: Ref. 6 - 17
6 547549R1 1 RING - retaining, front head
10 238-6012 1 O-RING, -012, 90 Duro, .364" ID x .070" Thk
11 108999C1 1 WIPER - rod
12 108997C1 1 RING - backup
14 108998C1 1 RING - backup
15 238-6121 1 O-RING, -121, 90 Duro, 1.049" ID x .103" Thk
16 532529R2 1 RING - quad
17 239-5119 1 SEAL - quad, 15/16 ID x 3/32 inch
8-16 REEL LIFT MASTER CYLINDER
8-16 REEL LIFT MASTER CYLINDER

128723A1 1 CYLINDER ASSEMBLY - 38 (1-1/2) ID x 238 mm (9-3/8 inch) stroke, reel lift, master, Includes: Ref. 1 -
12
2 547384R1 1 GLAND - cylinder
3 128724A1 1 ROD - piston
4 547333R3 1 PISTON - cylinder
5 548033R1 1 NUT - hex jam, self locking, 3/4 inch NF
547388R94 1 KIT - seal, Includes: Ref. 7 - 12
7 239-5123 1 SEAL - quad, 1-3/16 ID x 3/32 inch
8 547383R2 1 RING - seal
10 238-6126 1 O-RING - 1-3/8 ID x 3/32 inch wide
11 1272317C1 1 SEAL - rod
12 564808R91 1 WIPER - rod
8-18 REEL LIFT SLAVE CYLINDER
8-18 REEL LIFT SLAVE CYLINDER

128726A1 1 CYLINDER ASSEMBLY - 25 (1) ID x 238 mm (9-3/8 inch) stroke, reel lift, slave, Includes: Ref. 1 - 7
2 463-1104 1 SCREW, Hex Hd, #10-24 x 1/4"
3 128727A1 1 ROD - piston
4 145190C1 1 RING - retaining
532531R92 1 KIT - seal, Includes: Ref. 5 - 7
5 532773R1 1 WIPER - piston rod
6 533145R1 1 WASHER - rubber bonded
7 119185C1 1 SEAL - piston rod
8-20 HEADER TO COMBINE CONNECTING HOSES, 1420, 1440, 1460 AND 1480 COMBINE
8-20 HEADER TO COMBINE CONNECTING HOSES, 1420, 1440, 1460 AND 1480 COMBINE

1 179202C1 1 HOSE - 1727 mm (68 inch) long, header to combine reel lift
2 218-5057 1 ADAPTER - straight, 9/16-18 inch flare x O-ring boss
4 187563C1 1 COUPLING - female, 9/16-18 inch, thread
5 165678C91 2 HOSE - 1676 mm (66 inch) long, header to combine reel drive, header to combine pick up drive
8 395149R1 1 COUPLER - male, 7/8 inch NF
8-22 REEL FORE AND AFT ATTACHMENT, 1420, 1440, 1460 OR 1480 COMBINE
8-22 REEL FORE AND AFT ATTACHMENT, 1420, 1440, 1460 OR 1480 COMBINE

1957287C1 1 KIT - reel fore and aft, Includes: Ref. 1 - 29
1 REF 1 VALVE ASSEMBLY - control, See Figure 8-24
3 218-5128 2 ELBOW - 90 degree, 9/16-18 flare x 3/4-16 inch adj O-ring boss
4 1321591C1 1 HOSE - reel, 2400 mm (94-1/2 inch) long, 5/16 ID
5 1284369C1 1 HOSE - 3300 mm (130 inch) long, reel aft, 5/16 ID
7 218-5354 2 FITTING, 9/16"-18, 37° x 7/8"-14, O-Ring
11 306132C1 5 STRAP - tie, 14 inch, nylon
13 1301630C2 2 TUBE - through
15 424-496 3 BOLT - hex, 1/4 NC x 6 inch, grade 2
16 493-41026 3 WASHER - external tooth lock, 1/4 inch
17 1301637C1 2 ORIFICE - valve
20 1866277R1 1 HARNESS - wiring
21 1301175C1 1 SWITCH - fore and aft
22 440-1068 2 SCREW - machine, pan Phillips, No. 6 NC x 1/2 inch
23 1301940C3 1 COVER - console extension
24 24613R1 4 SCREW - oval head, No. 10-16 x 3/4 inch
25 262965C91 1 BREAKER - circuit, 10 ampere
26 492-11010 2 Washer, Lock, #10
27 225-14210 2 NUT, #10-32
28 22-824 3 STRAP - tie, 7 inch, retaining
29 537024R1 1 CLIP - edge
8-24 DOUBLE PILOTED VALVE ASSEMBLY, REEL FORE AND AFT ATTACHMENT
8-24 DOUBLE PILOTED VALVE ASSEMBLY, REEL FORE AND AFT ATTACHMENT

124857A1 1 VALVE ASSEMBLY - double piloted, Includes: Ref. 1 - 40
1 100475A1 2 PLUG - end cap
3 100474A1 2 SPRING - centering
4 237-6010 2 O-RING, 10-1, 90 Duro, .755" ID x .097" Thk, Part of valve seal kit P/N 1282278C2
5 1301687C1 2 RETAINER - spring
6 238-6019 2 O-RING, -019, 90 Duro, .801" ID x .070" Thk, Part of valve seal kit P/N 1282278C2
7 1301627C3 2 SLEEVE - poppet
8 1301624C1 2 BUSHING - poppet
9 1301640C1 2 SPRING - poppet
10 1301648C1 2 ARMATURE - valve, poppet
11 1301624C1 2 BUSHING - poppet, pole
13 110550A1 2 POPPET - valve
19 124777A1 1 SPOOL - shuttle
24 NSS 1 BODY - valve
25 NSS 1 SPOOL - valve
30 124775A1 1 BODY - check valve, end cap
32 1272887C1 1 SPRING - poppet, spool
33 124771A1 1 POPPET - valve, spool
35 1267163C1 1 SEAT - valve
36 1301633C1 2 COIL - valve
37 1301632C1 2 COVER - coil
38 107825 2 NUT - hex, 1/2 inch NF, stamped
39 225-20210 2 NUT, #10-32, Brass
1282278C2 1 KIT - valve seal, Includes: Ref. 4, 6, 14, 31 and 34
8-26 REEL DRIVE SYSTEM, 1440E, 1460E AND 1480E COMBINE
8-26 REEL DRIVE SYSTEM, 1440E, 1460E AND 1480E COMBINE

1 REF 1 PUMP ASSEMBLY - reel drive, See Figure 8-32
2 409-7824 2 BOLT - hex serrated flange, 1/2 NC x 1-1/2 inch
3 231-5148 2 NUT, Flg, USR, 1/2"-13
4 1282383C1 1 FITTING - beaded tube, 1 inch ID hose
5 237-6020 1 O-RING, 20-1, 90 Duro, 1.475" ID x .118" Thk
6 218-5119 1 ELBOW - 90 degree, 7/8-14 flare x 1-1/16-12 inch adj O-ring boss
8 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .116" Thk
9 1315460C1 1 HOSE - pump pressure, 900 mm (35 inch) long, hydraulic, 1/2 ID
10 237-6010 UAR O-RING, 10-1, 90 Duro, .755" ID x .097" Thk
11 413-552 2 BOLT - hex, 5/16 NC x 3-1/4 inch
12 425-105 2 NUT - hex, 5/16 inch NC
13 492-11031 2 WASHER, LOCK, 5/16"
14 REF 1 VALVE ASSEMBLY - reel drive, See Figure 8-30
15 198303C1 1 HOSE - 1016 mm (40 inch) long, cut from 190851C2 hose, suction
16 214-1416 2 CLAMP, HOSE, #16, 0.81/1.50 Type F Worm, Adj.
21 196746C1 1 TUBE - reel drive return, 1460E Combine., 1440E Combine.
21 187830C1 1 TUBE - reel drive return, 1480E Combine.
22 NSS 1 HOSE - return, 24 inch (Order S118576 and cut to length)
23 1312411C1 1 TUBE - reel drive return, 1460E Combine., 1440E Combine.
23 1325306C1 1 TUBE - reel drive return, 1480E Combine.
24 306132C1 1 STRAP - tie, 14 inch, nylon
8-28 REEL DRIVE SYSTEM, 1440E, 1460E AND 1480E COMBINE (CONT'D)
8-28 REEL DRIVE SYSTEM, 1440E, 1460E AND 1480E COMBINE (CONT'D)

26 165601C1 UAR CLAMP - reservoir drain tube, retaining, 13/32 inch diameter hole
26 165602C1 UAR CLAMP - retaining, 11/32 inch diameter hole
27 196868C2 UAR PLATE - support, tube, 1460E Combine with 54.5 inch feeder., 1460E Combine with 47 inch feeder.,
1440E Combine with 47 inch feeder.
28 573186R1 UAR BAR - support, tube, 1480E Combine with 54.5 inch feeder.
29 413-520 UAR BOLT - hex, 5/16 NC x 1-1/4 inch
29 424-628 UAR BOLT - hex, 3/8 NC x 1-3/4 inch, grade 2
30 231-5145 UAR NUT - hex serrated flange, 5/16 inch NC
30 231-5146 UAR NUT, Flg, USR, 3/8"-16
31 163490C1 UAR INSULATOR - rubber, 3/8 ID x 1-13/64 inch long, tube clamp
32 183821C1 UAR CLAMP - tube, single, 3/8 inch OD tube
32 183822C1 UAR CLAMP - tube, single, 5/8 inch OD tube
35 121714C1 UAR CLAMP - header lift tubes, tube, double, 3/4 and 5/8 inch OD tube
37 495-11028 UAR WASHER - flat, 9/32 x 5/8 x 1/16 inch
38 231-5144 UAR NUT, Flg, USR, 1/4"-20
39 218-5062 1 ADAPTER - straight, 7/8-14 inch flare x O-ring boss
40 395150R91 1 COUPLING - self sealing, female (Alternate with A177478)
40 A177478 1 COUPLING - self-sealing, female (Alternate with 395150R91)
41 395149R1 1 COUPLER - male, 7/8 inch NF (Alternate with 1272399C2)
41 1272399C2 1 COUPLER - self sealing, male, 7/8 inch NF (Alternate with 395149R1)
43 196878C1 1 HOSE - 1422 mm (56 inch) long, hydraulic, 3/8 ID, 1440E Combine with 47 inch feeder., 1460E
Combine with 47 inch feeder.
43 179411C1 1 HOSE - 1549 mm (61 inch) long, hydraulic, 3/8 ID, 1460E Combine with 54.5 inch feeder., 1480E
Combine with 54.5 inch feeder.
45 1312410C1 1 TUBE - reel lift, 1460E Combine with 47 inch feeder., 1460E Combine with 54.5 inch feeder., 1440E
Combine with 47 inch feeder.
46 187562C1 1 COUPLING - male, 9/16 NF inch
48 214-1412 2 CLAMP, HOSE, #12, 0.69/1.25 Type F Worm
49 1312409C1 UAR SUPPORT - pipe
50 614-10025 UAR BOLT, Hex, M10 x 25, 8.8, Full Thd
51 825-51410 UAR NUT - hex serrated flange, 10 mm - 1.5
8-30 REEL DRIVE VALVE
8-30 REEL DRIVE VALVE

1282369C91 1 VALVE ASSEMBLY - reel drive, Includes: Ref. 2 - 8
2 NSS 1 BODY - valve
3 1301336C2 1 MOTOR ASSEMBLY - valve, Includes: Ref. 4 & 5
6 1301996C1 1 VALVE - compensator
8 413-414 3 BOLT - hex, 1/4 NC x 7/8 inch
8-32 REEL DRIVE PUMP
8-32 REEL DRIVE PUMP

1272633C91 1 PUMP ASSEMBLY - reel drive, new, Includes: Ref. 1 - 23
1949288C1 1 PUMP ASSEMBLY - reel drive, remanufactured, North America only, component parts shown on this
page do not apply to the remanufactured assembly, Includes: Ref. 1 - 23
1949289C1 1 RETURN NUMBER - use this number to return pump core for credit when using a remanufactured
assembly
1 NSS 1 HOUSING - rear
4 NSS 1 GEAR ASSEMBLY - drive
5 NSS 1 GEAR ASSEMBLY - idler
6 NSS 1 BODY - pump
92586C1 1 KIT - seal repair, seal, Includes: Ref. 7 - 17
7 NSS 1 GASKET - backup
11 NSS 1 O-RING - backup
12 NSS 1 SEAL - bearing
14 NSS 1 PLATE - wear
15 NSS 1 WASHER - special
16 A25139 1 SEAL - shaft
17 100-21137 1 Ring, Snap, 1.375", Int, #137
20 NSS 1 HOUSING - front
21 166-55 4 BOLT - 12 point, 3/8 NC x 3-1/2 inch grade 8
22 166-59 4 BOLT - 12 point flange, 3/8 NC x 3-3/4 inch, grade 8
23 H233445 1 KEY - pump shaft
9A-02 6 BAT REEL, STEEL TINES
9A-02 6 BAT REEL, STEEL TINES

1 1326602C1 1 SHAFT - center (15.0 foot)
2 167653C1 UAR PLATE - reel arm (15.0, 16.5 and 17.5 foot)
2 180248C1 UAR PLATE - reel arm (20.0, 22.5, 25.0 and 30.0 foot)
3 1326650C1 UAR ARM - reel
4 413-58 UAR BOLT - hex, 5/16 NC x 1/2 inch
5 425-105 UAR NUT - hex, 5/16 inch NC
6 492-11031 UAR WASHER, LOCK, 5/16"
7 114938A1 1 HOUSING - eccentric roller, left-hand
8 167666C1 4 BUSHING - roller frame
12 114951A1 12 CUP - tapered roller bearing (Female thread)
13 114952A1 12 CONE - tapered roller bearing (Male thread)
20 219-3 2 FITTING - grease, straight, 1/8 PT x 1-1/4 inch
21 175571A2 1 HOUSING - eccentric roller, right-hand
175573A1 1 SHIELD ASSEMBLY - eccentric, includes shield 114940A1, bearings 114951A1 and 114952A1
22 114940A1 2 SHIELD - eccentric
23 614-8020 12 BOLT - hex, full threads, 8 - 1.25 x 20 mm
24 892-11008 12 WASHER, LOCK, M8
25 829-1408 12 NUT - hex, 8 mm - 1.25, class 10
26 167661C1 2 RING - control
27 1326656C1 UAR BUSHING - reel arm
29 231-4144 UAR NUT, LOCK, 1/4"-20, GB
30 114941A1 6 BEARING - roller, ref 30: 114941a1 BOLT IS NSS. IS MADE INTO ROLLER BEARING. (m10 x
1.5-6g bolt)
31 114942A1 12 BOLT - socket head, shoulder, special
32 832-46412 12 NUT - self-locking, 12 mm - 1.75
9A-04 6 BAT REEL, STEEL TINES (CONT'D)
9A-04 6 BAT REEL, STEEL TINES (CONT'D)

37 129996A1 1 SUPPORT - reel, left-hand
38 129997A1 1 SUPPORT - reel, right-hand
40 23885K 4 SPACER - 3/4 x 2-1/16 inch
43 814-12090 2 BOLT - hex, 12 - 1.75 x 90 mm
45 1316328C1 4 BUSHING - reel support
47 185519C1 1 SHAFT - driving end (15.0, 16.5 and 17.5 foot)
47 185520C1 1 SHAFT - driving end (20.0 and 22.5 foot)
47 180134C1 1 SHAFT - driving end (25.0 and 30.0 foot)
48 185522C1 1 SHAFT - driven end (15.0, 16.5 and 17.5 foot)
48 185523C1 1 SHAFT - driven end (20.0 and 22.5 Foot)
48 180135C1 1 SHAFT - driven end (25.0 and 30.0 foot)
49 495-81089 4 WASHER - flat, 1-21/32 x 2-1/4 x 7/64 inch
50 114943A1 1 COLLAR - locking, Includes: Ref. 51
51 878-1106 2 SCREW - set, hex socket headless cup point, 3/8 NF x 5/16 inch
52 413-612 UAR BOLT - hex, 3/8 NC x 3/4 inch
53 231-4116 UAR NUT - hex, self-locking, 3/8 inch NC
54 492-11038 UAR 3/8"
55 434-616 6 BOLT - carriage, 3/8 NC x 1 inch
56 113-2663 1 BOLT - hex, full threads, 1/2 NC x 3 inch
57 425-108 1 NUT - hex, 1/2 inch NC
58 135113A1 1 PLATE - support, outer
59 814-12080 2 Bolt, Hex, M12 x 80, 8.8
60 811-12040 2 BOLT, CARRIAGE, M12 x 40, Cl8.8, Full Thd
61 829-1412 2 NUT - hex, 12 mm - 1.75, class 10
62 114944A1 2 WASHER - Belleville, 12 mm
9A-06 6 BAT REEL, BAT AND STEEL TINE ASSEMBLY
9A-06 6 BAT REEL, BAT AND STEEL TINE ASSEMBLY

1 1326605C91 12 BAT ASSEMBLY - with steel tines (15.0 foot), Includes: Ref. 13 - 15
4 1316259C91 6 BAT ASSEMBLY - with steel tines (16.5 and 20.0 foot), Includes: Ref. 13 - 15
8 598170R91 12 BAT ASSEMBLY - with steel tines (25.0 foot), Includes: Ref. 13 - 15
12 598188R91 12 BAT ASSEMBLY - with steel tines (16.5 foot), Includes: Ref. 13 - 15
13 598171R1 UAR TINE - steel
14 592616R1 UAR CLIP - tine
15 23055R1 UAR RIVET - 3/16 x 1 inch, truss-head semi-tubular
16 412-422 UAR BOLT - carriage, 1/4 NC x 1-3/8 inch, grade 2
17 232-4114 UAR NUT, LOCK, 1/4"-20, GC
18 1326604C1 6 SHAFT - bat (15.0 foot)
18 1326842C1 6 SHAFT - bat (16.5 foot)
18 1316267C1 6 SHAFT - bat (17.5 foot)
18 1316268C1 6 SHAFT - bat (20.0 foot)
18 1316269C1 6 SHAFT - bat (22.5 foot)
18 1316270C1 6 SHAFT - bat (25.0 foot)
18 1316271C1 6 SHAFT - bat (30.0 foot)
19 1316568C1 12 BUSHING - (52 inch reel)
20 413-832 12 BOLT - hex, 1/2 NC x 2 inch (52 inch reel)
21 495-81024 12 WASHER - flat, 17/32 x 1-1/4 x 1/16 inch (52 inch reel)
24 231-4118 12 NUT - hex, self-locking, 1/2 inch NC (52 inch reel)
9A-08 6 BAT REEL, PLASTIC TINES, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER
9A-08 6 BAT REEL, PLASTIC TINES, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER

1 1989399C1 1 SHAFT - center tube (15.0 foot)
17 829-1412 1 NUT - hex, 12 mm - 1.75, class 10
19 114944A1 1 WASHER - belleville, 12 mm
21 1989433C2 6 SHIELD - end
175573A1 1 SHIELD ASSEMBLY - eccentric, includes shield 114940A1, bearings 114951A1 and 114952A1,
Includes: Ref. 22
24 892-11008 6 WASHER, LOCK, M8
25 829-1408 6 NUT - hex, 8 mm - 1.25, class 10
30 114941A1 3 BEARING - roller
9A-10 6 BAT REEL, PLASTIC TINES, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (CONT'D)
9A-10 6 BAT REEL, PLASTIC TINES, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (CONT'D)

40 23885K 4 SPACER - 3/4 x 2-1/16 inch
43 814-12080 4 Bolt, Hex, M12 x 80, 8.8
47 1989426C1 1 SHAFT - drive end
48 1989424C1 1 SHAFT - driven end
72 614-10050 UAR BOLT - hex, full threads, 10 - 1.5 x 50 mm
73 832-41310 UAR NUT - hex, self-locking, 10 mm - 1.5, class 10
74 892-11010 UAR WASHER - lock, 10 mm
75 1347084C1 UAR BEARING - reel arm
76 1347085C1 UAR STRAP - bearing
78 425-108 1 NUT - hex, 1/2 inch NC
126748A1 plastic, see service bulletin NHE SB 034 93
9A-12 6 BAT REEL, PLASTIC TINES, 22.5, 25.0 AND 30.0 FOOT HEADER
9A-12 6 BAT REEL, PLASTIC TINES, 22.5, 25.0 AND 30.0 FOOT HEADER

1 1347091C1 1 SHAFT - center, tube (22.5 foot)
9 175571A2 1 HOUSING - eccentric roller, right-hand
17 829-1412 2 NUT - hex, 12 mm - 1.75, class 10
19 114944A1 2 WASHER - belleville, 12 mm
175573A1 1 SHIELD ASSEMBLY - eccentric, includes shield 114940A1, bearings 114951A1 and 114952A1,
Includes: Ref. 22
24 892-11008 12 WASHER, LOCK, M8
25 829-1408 12 NUT - hex, 8 mm - 1.25, class 10
30 114941A1 6 BEARING - roller
34 832-46412 12 NUT - self-locking, 12 mm - 1.75, 12 mm
36 832-46410 6 NUT - self-locking, 10 mm - 1.5, 10mm
9A-14 6 BAT REEL, PLASTIC TINES, 22.5, 25.0 AND 30.0 FOOT HEADER (CONT'D)
9A-14 6 BAT REEL, PLASTIC TINES, 22.5, 25.0 AND 30.0 FOOT HEADER (CONT'D)

40 23885K 4 SPACER - 3/4 x 2-1/16 inch
43 814-12080 4 Bolt, Hex, M12 x 80, 8.8
47 1989428C1 1 SHAFT - drive end
48 1989425C1 1 SHAFT - driven end
72 614-10050 UAR BOLT - hex, full threads, 10 - 1.5 x 50 mm
73 832-41310 UAR NUT - hex, self-locking, 10 mm - 1.5, class 10
74 892-11010 UAR WASHER - lock, 10 mm
75 1347084C1 UAR BEARING - reel arm
76 1347085C1 UAR STRAP - bearing
78 425-108 1 NUT - hex, 1/2 inch NC
9A-16 6 BAT REEL, BAT AND PLASTIC TINES
9A-16 6 BAT REEL, BAT AND PLASTIC TINES

1 1989429C1 6 TUBE - tine support (15.0 foot)
2 1347094C1 6 BRACKET - crank arm, left-hand
3 1347095C1 6 BRACKET - crank arm, right-hand (Double eccentric)
4 838-1840 UAR PIN - roll, 8 x 40 mm
5 1989468C1 UAR WASHER - flat, special, 35.6 x 46 x 2.0 mm
6 126748A1 UAR WASHER - thrust, plastic
1989441C1 UAR KIT - tine, end, Includes: Ref. 7 & 8
7 NSS 6 TINE - end
8 126173A1 6 SCREW - hex washer head, slotted tap, special, 3.5 x 1.3 x 16 mm
1989439C1 UAR KIT - tine, right-hand, Includes: Ref. 9 & 10
9 NSS 6 TINE - right
1989440C1 UAR KIT - tine, left-hand, Includes: Ref. 11 & 12
11 NSS 6 TINE - left
1989438C1 UAR KIT - tine, full, Includes: Ref. 13 & 14
13 NSS 10 TINE - full
9A-18 AUXILIARY PICKUP TINES, 6 BAT REEL WITH STEEL TINES
9A-18 AUXILIARY PICKUP TINES, 6 BAT REEL WITH STEEL TINES

167605C91 6 TINE ASSEMBLY - auxiliary pickup, left-hand, Includes: Ref. 1 & 2
1 592627R21 1 STRAP - finger
2 167652C1 1 TINE - left-hand
167606C91 6 TINE ASSEMBLY - auxiliary pickup, right-hand, Includes: Ref. 4 & 5
4 592627R21 1 STRAP - finger
5 167651C1 1 TINE - right-hand
6 598246R1 12 SPACER - 9/16 ID x 1-1/4 inch
7 827385C1 12 BOLT - round head hex shank, special, 1/2 NF x 2-1/2 inch
8 827386C1 12 NUT - hex flange, self-locking, 1/2 inch NF
9A-20 AUXILIARY PICKUP TINE, 6 BAT REEL WITH PLASTIC TINES
9A-20 AUXILIARY PICKUP TINE, 6 BAT REEL WITH PLASTIC TINES

1970589C1 1 TINE ASSEMBLY - auxiliary pickup, Includes: Ref. 2 - 6
1 827385C1 12 BOLT - round head hex shank, special, 1/2 NF x 2-1/2 inch
2 598246R1 12 SPACER - 9/16 ID x 1-1/4 inch
3 1970591C1 12 RETAINER - auxiliary tine
4 1970590C1 12 TINE - plastic, auxiliary
5 1970592C1 12 SUPPORT - auxiliary tine
6 827386C1 12 NUT - hex flange, self-locking, 1/2 inch NF
9A-22 REEL DRIVE
9A-22 REEL DRIVE

1 REF 1 MOTOR ASSEMBLY - reel drive, See Figure 8-12
2 413-828 2 BOLT - hex, 1/2 NC x 1-3/4 inch
3 129-857 2 NUT - heavy square, 1/2 inch NC, grade 2
5 1308371C1 1 SHIM - bar
6 129973A2 1 SPROCKET - driven, 51 tooth
7 432-616 2 3/32" x 1"
8 27-7278 2 PIN - clevis, 7/16 x 2-25/32 inch, hardened
9 NSS 1 CHAIN ASSEMBLY - reel drive (Use 67 links from bulk chain 1315D, 1 connecting link 241-1315, and
2 offset links 241-1715)
10 129967A1 1 SPROCKET - drive, 17 tooth
11 484-1386 2 SCREW - set, hex socket headless, 3/8 NF x 3/8 inch, cup point
12 126-124 1 Woodruff Key, #15, 1/4" x 1", HT
18 425-108 1 NUT - hex, 1/2 inch NC
19 80679 2 Washer, Lock, 1/2"
9A-24 REEL DRIVE SHIELD
9A-24 REEL DRIVE SHIELD

140214A2 1
SHIELD ASSEMBLY - reel drive (No longer available, order components), Includes: Ref. 1 - 5
1 140216A2 1
SUPPORT - reel drive shield
2 439-1428 2
PIN - headed, 1/4 x 1-3/4 inch, grade 2
3 432-612 2
PIN , SPLIT (COTTER), 3/32" x 3/4"
4 140218A3 1
SHIELD - reel drive (Replaces 140215A2), Includes: Ref. 5, THE PARTS NOTES STATES: MUST
USE SUPPORT 258981A1, SUPPORT 258980A1 AND LATCH 291944A1. CAN SEE IN LATER
1010 BOOKS. CNS/CAM 2/4/98
5 144385A1 1 DECAL - Warning, shields are provided to guard
6 465593R1 1 SPACER - mounting
7 413-552 1 BOLT - hex, 5/16 NC x 3-1/4 inch
9 409-7512 UAR BOLT - hex serrated flange, 5/16 NC x 3/4 inch
9A-26 REEL SUPPORT ARMS AND LIFT CYLINDERS
9A-26 REEL SUPPORT ARMS AND LIFT CYLINDERS

1 1308352C3 2 ARM - support
4 128428A2 2 SUPPORT - arm
5 413-848 4 BOLT - hex, 1/2 NC x 3 inch
7 439-5848 2 PIN - headed, 1/2 x 3 inch
8 432-1216 2 3/16" x 1"
9 1320928C1 2 ROD - stand support
12 M296 2 SPRING - compression
14 432-812 2 PIN, SPLIT (COTTER), 1/8" x 3/4"
15 1305175C3 2 BRACKET - reflector
20 432-1216 2 3/16" x 1"
23 439-5848 2 PIN - headed, 1/2 x 3 inch
24 413-812 2 BOLT - hex, 1/2 NC x 3/4 inch
25 1320927C2 2 ROD - cylinder adjusting
26 480523R1 2 PIN - hair, cotter
28 1316193C1 2 PLUG - button
29 128729A1 2 TUBE - reel arm adjusting
30 144672A2 1 SUPPORT - lift cylinder, left-hand, with decal
30 144673A2 1 SUPPORT - lift cylinder, right-hand, with decal
31 185067A1 1 DECAL - Warning, avoid injury, always lock both reel lift cylinders
32 128427A1 2 SPACER - reel arm
33 413-1272 2 BOLT - hex, 3/4 NC x 4-1/2 inch
35 496-21081 2 WASHER, 13/16" x 1 1/2" x .179", HDN
36 128426A1 2 SPACER - support
37 413-1028 2 BOLT - hex, 5/8 NC x 1-3/4 inch
39 496-41066 2 WASHER, 21/32" x 1 1/2" x .188", HDN
9A-28 REEL FORE AND AFT ADJUSTMENT, HYDRAULIC
9A-28 REEL FORE AND AFT ADJUSTMENT, HYDRAULIC

1 1316318C2 1 SUPPORT - front, right-hand cylinder
2 413-852 2 BOLT - hex, 1/2 NC x 3-1/4 inch
5 413-848 2 BOLT - hex, 1/2 NC x 3 inch
6 1316332C2 1 SUPPORT - rear, left-hand cylinder
7 REF 2 CYLINDER ASSEMBLY - reel fore and aft, See Figure 8-14
8 439-5628 2 PIN - headed, 3/8 x 1-3/4 inch
9 439-1636 2 PIN - headed, 3/8 x 2-1/4 inch, grade 2
10 432-812 4 PIN, SPLIT (COTTER), 1/8" x 3/4"
9A-30 REEL FORE AND AFT ADJUSTMENT, MECHANICAL
9A-30 REEL FORE AND AFT ADJUSTMENT, MECHANICAL

1 129986A1 2 SUPPORT - reel adjusting
3 413-848 4 BOLT - hex, 1/2 NC x 3 inch
5 129983A1 2 CRANK - reel adjusting
6 495-21081 2 WASHER - flat, 13/16 x 2 x 9/64 inch
7 432-1020 2 5/32" x 1 1/4"
9A-32 REEL CONTROL ATTACHMENT, HYDRAULIC REEL DRIVE, 1440E, 1460E, AND 1480E COMBINE
9A-32 REEL CONTROL ATTACHMENT, HYDRAULIC REEL DRIVE, 1440E, 1460E, AND 1480E COMBINE

1 189459C3 1 SHIELD - pump drive, 1440E Combine with 47 inch feeder., 1460E Combine with 47 inch feeder.
1 189460C3 1 SHIELD - pump drive, 1460E Combine with 54.5 inch feeder., 1480E Combine with 54.5 inch feeder.
2 189470C1 1 SUPPORT - shield, upper
3 477-73108 UAR BOLT - serrated slotted truss head, 5/16 NC x 1/2 inch
6 197646C1 1 SHIELD - feeder jackshaft, 1460E Combine with 47 inch feeder., 1440E Combine with 47 inch feeder.
6 189730C1 1 SHIELD - feeder jackshaft, 1460E Combine with 54.5 inch feeder., 1480E Combine with 54.5 inch
feeder.
7 179253C1 1 SHIELD - feeder jackshaft, 1480E Combine with 54.5 inch feeder., 1460E Combine with 54.5 inch
feeder.
9 477-82508 4 BOLT - serrated slotted truss head, 1/4 NC x 1/2 inch
10 231-5144 4 NUT, Flg, USR, 1/4"-20
13 203672C1 1 SUPPORT - shield, lower, 1480E Combine with 54.5 inch feeder.
14 189468C2 1 SUPPORT - shield, lower rear, 1460E Combine with 47 inch feeder., 1440E Combine with 47 inch
feeder.
15 189469C1 1 SUPPORT - shield, lower rear, 1460E Combine with 54.5 inch feeder., 1480E Combine with 54.5 inch
feeder.
16 189464C2 1 SUPPORT - shield, upper front
495-11053 UAR WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
80679 UAR Washer, Lock, 1/2"
425-108 UAR NUT - hex, 1/2 inch NC
21 189466C1 1 SUPPORT - shield, upper rear
23 198409C2 1 SUPPORT - reel drive pump
24 154273C1 UAR BOLT - hex, self-locking, special, 3/8 NC x 1 inch
25 231-5146 UAR NUT, Flg, USR, 3/8"-16
9A-34 REEL CONTROL ATTACHMENT, HYDRAULIC REEL DRIVE, 1440E, 1460E, 1480E COMBINE (CONT'D)
1330177C2, pulley is 5" O.D.

9A-34 REEL CONTROL ATTACHMENT, HYDRAULIC REEL DRIVE, 1440E, 1460E, 1480E COMBINE (CONT'D)

28 176562C2 1 PULLEY - drive, feeder jackshaft pump, 13-1/2 inch OD
29 Q1497 1 KEY - square gib, 3/8 x 2 inch
30 197414C2 1 BELT - reel drive, 146 inch, 1480E Combine with 54.5 inch feeder., 1460E Combine with 54.5 inch
feeder.
30 197411C1 1 BELT - reel drive, 132 inch, 1460E Combine with 47 inch feeder., 1440E Combine with 47 inch feeder.
31 195528C92 1 ARM ASSEMBLY - pump tightener, Includes: Ref. 32
32 583346R1 2 BUSHING - tightener arm
33 219-87 1 NIPPLE, LUBE, 1/4"-28 x .56" lg, Self-Tap
34 198410C1 1 SPACER - tightener arm
35 413-1064 1 BOLT - hex, 5/8 NC x 4 inch
36 495-81026 1 WASHER - flat, 21/32 x 1-1/2 x 3/64 inch
39 231-51410 1 NUT, Flg, USR, 5/8"-11
42 674966R91 1 PULLEY - belt idler, 8-3/4 inch OD
43 424-1080 1 BOLT - hex, 5/8 NC x 5 inch, grade 2
45 492-11062 1 WASHER, LOCK, 5/8"
46 425-1010 1 NUT, 5/8"-11, G5
47 193252C1 1 PULLEY ASSY, pump driven, 7.5" O.D., 7/8" I.D.
48 485-13812 UAR SCREW - set, square head, 3/8 NC x 3/4 inch, cup point
49 425-146 UAR NUT - hex, jam, 3/8 inch NC
52 195526C1 1 SUPPORT - pivot anchor, 1440E Combine with 47 inch feeder., 1460E Combine with 47 inch feeder.,
1460E Combine with 54.5 inch feeder.
52 195527C1 1 SUPPORT - pivot anchor, 1480E Combine with 54.5 inch feeder.
53 434-616 UAR BOLT - carriage, 3/8 NC x 1 inch
54 434-820 UAR BOLT - carriage, 1/2 NC x 1-1/4 inch
55 496-21053 UAR WASHER - flat, 17/32 x 1-1/16 x 1/8 inch, hardened
56 232-5138 UAR NUT, Flg, USR, 1/2"-13, G8
57 195531C1 1 SUPPORT - spring anchor
58 409-7612 UAR BOLT - hex serrated flange, 3/8 NC x 3/4 inch
60 167570C1 1 CHAIN - latch, reel drive idler pulley arm
61 413-416 1 BOLT - hex, 1/4 NC x 1 inch
63 492-11025 1 WASHER, LOCK, 1/4"
64 425-104 1 NUT - hex, 1/4 inch NC
65 P303 1 SPRING - reel drive idler pulley arm
1330177C2, pulley is 5" O.D.

9A-36 REEL DRIVE, DRIVES, 1440E, 1460E AND 1480E COMBINE
For Combines Previously Equipped With 825 Headers. 1330177C2, pulley is 5" o.d.
9A-36 REEL DRIVE, DRIVES, 1440E, 1460E AND 1480E COMBINE

1 195528C92 1 ARM ASSEMBLY - pump tightener, Includes: Ref. 2
2 583346R1 2 BUSHING - tightener arm
4 674966R91 1 PULLEY - belt idler, 8-3/4 inch OD
5 413-1080 1 BOLT - hex, 5/8 NC x 5 inch
7 492-11062 1 WASHER, LOCK, 5/8"
8 425-1010 2 NUT, 5/8"-11, G5
12 193252C1 1 PULLEY ASSY, pump driven, 7.5" O.D., 7/8" I.D.
13 485-13812 2 SCREW - set, square head, 3/8 NC x 3/4 inch, cup point
14 425-146 2 NUT - hex, jam, 3/8 inch NC
15 1315461C1 ,1 BRACKET - reel speed valve
17 413-522 2 BOLT - hex, 5/16 NC x 1-3/8 inch
18 492-11031 2 WASHER, LOCK, 5/16"
20 425-105 2 NUT - hex, 5/16 inch NC
23 1301176C1 1 SWITCH - rocker
24 342-10610 UAR SCREW - machine, oval Phillips, No. 6 NC x 5/8 inch
For Combines Previously Equipped With 825 Headers. 1330177C2, pulley is 5" o.d.
9B-02 KNIFE GUARDS AND CUTTER BAR, 1.5 INCH KNIFE
9B-02 KNIFE GUARDS AND CUTTER BAR, 1.5 INCH KNIFE

1 REF 1 KNIFE ASSEMBLY - header, 1.5 inch, See Figure 9B-06
2 1307412C1 1 BAR - cutter (15.0 foot)
2 1326813C1 1 BAR - cutter (16.5 foot)
2 1307413C1 1 BAR - cutter (17.5 foot)
2 1307414C1 1 BAR - cutter (20.0 foot)
2 1307415C1 1 BAR - cutter (22.5 foot)
2 1307416C1 1 BAR - cutter (25.0 foot)
2 1307417C1 1 BAR - cutter (30.0 foot)
5 1316040C1 UAR SHIM - .067 inch, knife guard
7 434-740 2 BOLT - carriage, 7/16 NC x 2-1/2 inch
8 1313463C1 UAR NUT - hex small flange lock, 7/16 inch NC
9 101001A2 UAR CLIP - knife hold down, ref #9 - if dlr looking for high arch, p/n sh/be 112428a1 per aj, dmm 9/9/97
13 REF 1 BOX ASSEMBLY - knife drive, See Figure 9B-12
14 326-1036 2 BOLT, Hex, 5/8"-11 x 2 1/4", G8
16 433-732 2 BOLT - carriage, 7/16 NC x 2 inch, , grade 5
17 1326538C91 UAR LIFTER - grain
18 1316688C4 1 SUPPORT - crop deflector, right-hand
19 1313160C1 UAR CLIP - hold down
21 104155A1 UAR SHIM - .093 inch, hold down clip
22 1989552C1 UAR GUARD - knife, 4 point
23 100999A1 1 GUARD - 2 point, left-hand (15.0, 20.0, 25.0 and 30.0 foot)
24 101000A1 1 GUARD - 2 point, right-hand (15.0, 20.0, 25.0 and 30.0 foot)
28 1957435C3 1 SUPPORT - crop deflector, left-hand
9B-04 KNIFE GUARDS AND CUTTER BAR, 3 INCH KNIFE
9B-04 KNIFE GUARDS AND CUTTER BAR, 3 INCH KNIFE

1 REF 1 KNIFE ASSEMBLY - header, 3 inch, See Figure 9B-10
2 1307412C1 1 BAR - cutter (15.0 foot)
2 1326813C1 1 BAR - cutter (16.5 foot)
2 1307413C1 1 BAR - cutter (17.5 foot)
2 1307414C1 1 BAR - cutter (20.0 foot)
2 1307415C1 1 BAR - cutter (22.5 foot)
2 1307416C1 1 BAR - cutter (25.0 foot)
2 1307417C1 1 BAR - cutter (30.0 foot)
3 1307299C1 UAR GUARD - double
5 1338269C1 2 GUARD - stub (15.0, 20.0, 25.0 and 30.0 foot)
6 1326787C2 3 GUARD - double, left
8 1313463C1 UAR NUT - hex small flange lock, 7/16 inch NC
9 1307280C3 UAR CLIP - knife hold down, low arch
10 180151 UAR BOLT - hex, special, 7/16 NC x 1-3/4 inch
11 REF 1 BOX ASSEMBLY - knife drive, See Figure 9B-12
13 326-1036 2 BOLT, Hex, 5/8"-11 x 2 1/4", G8
17 608787R91 UAR LIFTER - grain
18 163417C91 UAR LIFTER - grain, heavy duty
19 1313160C1 UAR CLIP - hold down
20 180149 UAR BOLT - hex, 7/16 NC x 1-1/2 inch
22 1326342C3 1 SUPPORT - crop deflector
433-724 BOLT carriage, 7/16-14 x 1-1/2"
433-728 BOLT carriage, 7/16-14 x 1-3/4"
9B-06 KNIFE ASSEMBLY, 1.5 INCH - BOLTED, (TRW)
9B-06 KNIFE ASSEMBLY, 1.5 INCH - BOLTED, (TRW)

1 1970400C5 1 KNIFE ASSEMBLY - 20 foot, Includes: Ref. 2 - 16
2 NSS 1 BAR - knife back
3 1313795C94 1 HEAD ASSEMBLY - knife, Includes: Ref. 4
4 1345491C2 1 COVER - dust
5 425-1310 1 NUT - hex, slotted, 5/8 inch NF
7 432-824 1 1/8" x 1-1/2"
8 1313797C1 1 BLOCK - knife head
9 219-93 1 FITTING - grease, 90 degree, 1/4-28 special taper x 3/4 inch, if used
9 219-87 1 NIPPLE, LUBE, 1/4"-28 x .56" lg, Self-Tap , If used
12 1970390C4 UAR SECTION - overserrated knife, 1-1/2 inch
12 191257A1 UAR SECTION - overserrated knife, 1-1/2 inch, chrome , if used
13 1970506C1 16 BOLT - round head oval neck, special, No. 12 NC x 1-1/8 inch, Grade 8
14 1954816C1 16 NUT - hex, self-locking, special, No. 12 NC
15 1970505C1 UAR BOLT - round head oval neck, special, No. 12 NC x 17/32 inch, Grade 8
16 1970507C2 UAR NUT - hex, self-locking, special, No. 12 NC
17 413-636 1 BOLT - hex, 3/8 NC x 2-1/4 inch, for spare knife
18 495-21044 1 WASHER - flat, 7/16 x 1 x 5/64 inch, for spare knife
19 231-5146 1 NUT, Flg, USR, 3/8"-16, For spare knife
9B-08 KNIFE ASSEMBLY - COARSE, 3 INCH - BOLTED, (TRW)
9B-08 KNIFE ASSEMBLY - COARSE, 3 INCH - BOLTED, (TRW)

1 1307281C98 1 KNIFE ASSEMBLY - 15.0 foot, Includes: Ref. 2 - 17
2 NSS 1 BAR - knife back
3 1316161C94 1 HEAD ASSEMBLY - knife, Includes: Ref. 4
4 1345491C2 1 COVER - dust
5 425-1310 1 NUT - hex, slotted, 5/8 inch NF
7 432-824 1 1/8" x 1-1/2"
10 1313797C1 1 BLOCK - knife head
11 219-93 1 FITTING - grease, 90 degree, 1/4-28 special taper x 3/4 inch, if used
11 219-87 1 NIPPLE, LUBE, 1/4"-28 x .56" lg, Self-Tap , If used
12 112074A1 UAR SECTION - knife, overserrated, 3 inch
12 191256A1 UAR SECTION - knife, overserrated 3 inch, chrome, if used
13 148200C1 1 SECTION - knife, 3 inch, right-hand end
14 1316030C2 1 SECTION - knife, 3 inch, plain half
15 1979166C1 16 BOLT - truss head ribbed neck, special, No. 12 NC x 1-1/8 inch
16 700708646 UAR SCREW - truss head ribbed neck, special, No. 12 NC x 5/8 inch, no longer available, order 700705296,
see below, Part of bolt and lock nut package P/N 700705296.
17 1954816C1 UAR NUT - hex, self-locking, special, No. 12 NC
18 227455A1 1 STRAP - knife back reinforcement, if used, Part of Knife Back Reinforcement Kit, P/N 227213A1
19 227456A1 3 SCREW - machine, socket head, special, No.12 NC x 1-1/4 inch, Part of Knife Back Reinforcement Kit,
P/N 227213A1
20 227457A1 6 SCREW - machine, socket head, special, No. 12 NC x 13/16 inch, Part of Knife Back Reinforcement
Kit, P/N 227213A1
21 1954816C1 9 NUT - hex, self-locking, special, No. 12 NC, Part of Knife Back Reinforcement Kit, P/N 227213A1
22 413-636 1 BOLT - hex, 3/8 NC x 2-1/4 inch, for spare knife
23 495-21044 1 WASHER - flat, 7/16 x 1 x 5/64 inch, for spare knife
24 231-5146 1 NUT, Flg, USR, 3/8"-16, For spare knife
700705296 UAR PACKAGE - bolt and lock nut, box of 50 each, Includes: Ref. 16
227213A1 1 KIT - knife back reinforcement, Includes: Ref. 18 - 21
9B-10 KNIFE DRIVE
9B-10 KNIFE DRIVE

1 125957A1 1 PULLEY - drive, 400 RPM, 213 mm OD (Standard on 1.5 inch knife)
1 126012A1 1 PULLEY - drive, 460 RPM, 245 mm OD (Optional on 1.5 inch knife only)
1 125959A1 1 PULLEY - drive, 500 RPM, 267 mm OD (Standard on 3 inch knife and optional on 1.5 inch knife)
1 125962A1 1 PULLEY - drive, 600 RPM, 318 mm OD (Optional on 3 inch knife only)
2 133587A1 4 BOLT - hex flange, self-locking, special, 3/8 NC x 3/4 inch
3 125966A1 1 HUB - knife drive pulley
4 413-832 2 BOLT - hex, 1/2 NC x 2 inch
5 425-108 2 NUT - hex, 1/2 inch NC
6 1989679C1 1 BELT - drive, 105 inch (Used with 400 RPM drive)
6 1319245C2 1 BELT - drive, 108-1/4 inch (Used with 460 and 500 RPM drive)
6 1316575C2 1 BELT - drive, 111-7/8 inch, drive, (Used with 600 RPM drive)
7 138435A1 1 SUPPORT - stationary idler pulley
8 409-7816 3 BOLT - hex serrated flange, 1/2 NC x 1 inch
9 231-5148 3 NUT, Flg, USR, 1/2"-13
10 518926R1 1 SPRING - knife drive idler, REF 10 Spring, IF looking for one that drives at both ends and has an
updated gear box, order p/n 1315247C1. 9/2/97 CNS/CAM
12 178858A1 1 TUBE - tightener spring, Ref 12: Another tube not shown? Per tech: Ref. 42, idler spacer, 188861A1.
Is called out but not illustrated in the catalog. It is 125 mm long and has an O.D. of 23.81 mm.
CAM/CNS 9/8/99
13 1307259C2 1 GUIDE - finger, tightener bolt
14 138439A1 1 ARM ASSEMBLY - idler, Includes: Ref. 15 & 16
15 289588R1 2 BUSHING - shield pivot support
20 1320826C1 1 BUSHING - idler arm
21 413-860 1 BOLT - hex, 1/2 NC x 3-3/4 inch
23 673214R91 1 PULLEY - 7-5/16 inch (186 mm) OD, idler, front
24 413-1040 1 BOLT - hex, 5/8 NC x 2-1/2 inch
25 425-1010 1 NUT, 5/8"-11, G5
26 492-11062 1 WASHER, LOCK, 5/8"
27 575098R1 1 SPACER - 7/8 x 5/8 inch, tube
28 1338456C1 1 PULLEY - idler, 6 inch OD, rear
29 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
32 1307324C1 1 BOLT - eye, knife drive tightener
34 425-108 3 NUT - hex, 1/2 inch NC
36 432-1216 1 3/16" x 1"
38 REF 1 BOX ASSEMBLY - knife drive
39 326-1032 4 BOLT, Hex, 5/8"-11 x 2", G8
40 326-1056 1 BOLT, Hex, 5/8"-11 x 3 1/2", G8
9B-10 KNIFE DRIVE

42 188861A1 1 SPACER - 5 inch, idler spring, inner
9B-12 KNIFE DRIVE BOX ASSEMBLY
9B-12 KNIFE DRIVE BOX ASSEMBLY

1 133157A2 1 BOX ASSEMBLY - knife drive, Includes: Ref. 2 - 34
2 182581A1 1 SHAFT - wobble
3 130820A1 1 HOUSING ASSEMBLY - knife box, Includes: Ref. 4 & 5
4 140436A1 1 BEARING - needle
5 544667R91 1 SEAL - oil
6 217-407 1 PLUG, Hex Hd, 3/8"-18
7 219-436 1 BREATHER - straight, 3/8 PT x 1-1/2 inch, housing
8 62520C2 1 TRUNNION - wobble shaft
9 364463C91 2 CONE - tapered roller bearing
10 364462C1 2 CUP - tapered roller bearing
11 133466A1 1 NUT - bearing lock, special
12 38-32024 2 Pin, 5/16" x 1 1/2", Coiled
130822A2 1 YOKE ASSEMBLY - trunnion, wobble shaft, Includes: Ref. 13 & 14
13 182580A1 1 YOKE - trunnion, wobble shaft
14 A12652 2 BEARING - needle
15 141162A1 2 STUD - trunnion
16 128962A1 1 SUPPORT ASSEMBLY - wobble box, Includes: Ref. 17 - 19
17 101295C1 1 SEAL - oil
18 205369R91 1 BEARING - needle
19 166957R91 1 BEARING - needle
21 136322C1 4 BOLT - hex dry lock, special, 5/8 NC x 2-1/4 inch, grade 8
22 492-11062 4 WASHER, LOCK, 5/8"
130821A1 1 COVER ASSEMBLY - knife drive box, Includes: Ref. 23 - 25
23 62526C1 1 COVER - knife drive box
24 F60368 1 BEARING - needle
25 62527C1 1 SEAL - oil
26 117045C1 8 BOLT - hex, special, 3/8 NC x 1 inch
27 62525C2 1 GASKET - cover
28 116955C1 1 GASKET - felt
29 126314A2 1 ARM - crank
30 116954C1 1 WASHER - flat, special, 5/32 x 2-13/32 x 5/16 inch
31 413-1224 1 BOLT - hex, 3/4 NC x 1-1/2 inch
32 138775A1 1 PULLEY - driven, knife
33 Q53 1 KEY, 1/4" Sq x 1", Par
34 414089C1 1 NUT - hex flange, special, 5/8 inch NF, grade 8
9B-14 KNIFE DRIVE SHIELD AND SUPPORTS
9B-14 KNIFE DRIVE SHIELD AND SUPPORTS

1 1316510C1 1 SUPPORT - shield, upper rear
4 1326758C1 1 SUPPORT - shield, upper front
13 1316693C3 1 SHIELD - knife drive
14 1326386C1 1 SUPPORT - shield, lower rear
16 231-5146 4 NUT, Flg, USR, 3/8"-16
17 188103C1 1 BRACKET - hood anchor
18 494307C1 1 HOOK - hold down, latch
19 439-1424 1 PIN, HEADED, 1/4" x 1 1/2", G2
20 432-816 1 1/8" x 1"
21 L105124 1 HOOK - latch
22 70-1108 2 SCREW - machine, pan head slotted, No. 10 NC x 1/2 inch
24 231-51409 2 NUT, Flg, USR, #10-24
25 1326408C2 2 STUD - fastener, shield
26 1326407C1 4 RETAINER - shield stud
27 495-81023 UAR WASHER - flat, 17/32 x 1-1/4 x 1/32 inch
33 131988A1 1 BRACKET - shield, front
35 231-5146 2 NUT, Flg, USR, 3/8"-16
37 126396A1 1 CABLE - shield anchor
34 477-73816 2 BOLT - serrated slotted truss head, 3/8 NC x 1 inch
9B-16 KNIFE JACKSHAFT DRIVE, 15.0 AND 16.5 FOOT HEADER

1 156816C91 2 BEARING - ball, jackshaft
2 180955C1 4 FLANGE - bearing
5 231-5146 6 NUT, Flg, USR, 3/8"-16
6 1320892C1 1 SUPPORT - jackshaft
7 183-123 2 SCREW - thumb with shoulder, 5/16 NC x 3/4 inch
8 488837C1 2 NUT - speed, 5/16 inch
11 231-5146 4 NUT, Flg, USR, 3/8"-16
14 125969A1 1 BAR - jackshaft
20 1326597C1 1 SHIELD - clutch
32 REF 1 DRIVE SHAFT ASSEMBLY - knife, See Figures 9B-24 - 9B-28
40 138005A1 1 HANGER - drive line
41 425-108 2 NUT - hex, 1/2 inch NC
45 225265R1 1 CLAMP - jackshaft
46 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
49 138653A1 1 SUPPORT - knife drive

4 434-620 3 BOLT, CARRIAGE, Short NK, 3/8"-16 x 1 1/4", G5, Full Thd
5 231-5146 8 NUT, Flg, USR, 3/8"-16
13 231-5148 1 NUT, Flg, USR, 1/2"-13
15 125970A1 1 BAR - jackshaft (17.5 foot)
18 125982A1 1 TUBE - jackshaft shield (17.5 foot)
19 282-1448 1 SCREW - self tapping, No. 8-18 x 1 inch
23 231-5146 4 NUT, Flg, USR, 3/8"-16
27 125992A1 1 SHIELD - jackshaft
32 REF 1 DRIVE SHAFT ASSEMBLY - knife, See Figures 9B-24 - 9B-28)
35 425-108 2 NUT - hex, 1/2 inch NC
46 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch

5 231-5146 6 NUT, Flg, USR, 3/8"-16
15 125972A1 1 BAR - jackshaft, 22.5 foot
18 125989A1 1 TUBE - jackshaft shield, 22.5 foot replaces 125984A1
18 178164A1 1 TUBE - jackshaft shield, 25.0 foot
23 231-5146 4 NUT, Flg, USR, 3/8"-16
35 425-108 2 NUT - hex, 1/2 inch NC
46 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
9B-22 KNIFE JACKSHAFT DRIVE, 30.0 FOOT HEADER
9B-22 KNIFE JACKSHAFT DRIVE, 30.0 FOOT HEADER

5 231-5146 9 NUT, Flg, USR, 3/8"-16
13 231-5148 1 NUT, Flg, USR, 1/2"-13
18 125985A1 1 TUBE - jackshaft shield
22 231-5146 4 NUT, Flg, USR, 3/8"-16
35 425-108 2 NUT - hex, 1/2 inch NC
40 125988A1 1 TUBE - jackshaft shield, replaces 125986A1
46 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
9B-24 KNIFE DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (BONDIOLI AND PAVESI)
9B-24 KNIFE DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (BONDIOLI AND PAVESI)

1 1313569C92 1 SHAFT ASSEMBLY - drive, auger (With decals), Includes: Ref. 2 - 32
1326658C92 1 SHAFT ASSEMBLY - female drive, Includes: Ref. 2 - 9
2 NSS 1 TUBE ASSEMBLY - outer
1330586C1 1 KIT - cross and bearing, Includes: Ref. 3 - 5
3 NSS 1 CROSS AND BEARING ASSEMBLY - drive shaft
4 933916R1 4 RING - internal retaining, 26 mm
5 933756R1 2 FITTING - grease, 6 x 1.00 mm, straight
6 1325022C1 1 YOKE - drive shaft
1311950C1 1 KIT - push pin, yoke, Includes: Ref. 7 & 8
7 NSS 1 PIN - yoke release
8 NSS 1 SPRING - return
9 1326528C1 1 DECAL - Danger, shield missing, do not operate
1326623C92 1 SHAFT ASSEMBLY - male drive, Includes: Ref. 10 - 18
10 NSS 1 TUBE - inner
11 NSS 1 YOKE - drive shaft
12 838-5845 1 PIN - roll, 8 x 45 mm
26 1326627C92 1 SHIELD ASSEMBLY - outer, Includes: Ref. 27
27 NSS 1 BEARING - shield
28 1326630C92 1 SHIELD ASSEMBLY - inner, Includes: Ref. 29
30 1326625C91 2 SHIELD ASSEMBLY - yoke, Includes: Ref. 31
32 1326632C1 2 CHAIN - drive shaft
9B-26 KNIFE DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (WALTERSHEID)
9B-26 KNIFE DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (WALTERSHEID)

1316216C91 1 SHAFT - drive, header, Includes: Ref. 2 - 21
2 1326494C1 2 SHIELD - drive shaft
3 1326500C1 2 COLLAR - drive shaft
4 1326498C1 4 RING - outer
5 1326499C1 2 BEARING - ball
6 1326490C1 2 YOKE ASSEMBLY - drive shaft, Includes: Ref. 7
7 1281458C1 1 KIT - pin
8 1281444C1 2 KIT - cross and bearing, drive shaft
11 1281445C1 1 YOKE - end, male
12 30907R1 2 PIN - slotted spring, 10 x 70 mm
13 1326501C1 1 TUBE - drive shaft, inner
14 1326495C1 2 FLANGE - guard
15 1281450C1 2 RING - bearing
17 1326503C1 1 SHIELD - outer
18 1326502C1 1 TUBE - drive shaft, outer
19 1326493C1 1 YOKE - end, female
20 1326504C1 1 TUBE - shield, inner
21 1281453C1 1 CHAIN - anti-rotation
9B-28 KNIFE DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (HAYES-DANA)
9B-28 KNIFE DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (HAYES-DANA)

1316990C91 1 SHAFT ASSEMBLY - drive (With decals), Includes: Ref. 3 - 40
3 NSS 1 TUBE - female, outer
4 NSS 1 YOKE - outer
757443 1 KIT - cross and bearing, drive shaft, Includes: Ref. 6 - 8
6 NSS 1 CROSS ASSEMBLY - bearing
7 606177R1 1 RING - retaining, 0.078 inch thick
7 1986059C1 1 RING - retaining, 0.058 inch thick
8 219-40 1 FITTING - grease, 65 degree, 1/8 PT x 7/8 inch
9 1326580C1 1 COLLAR - yoke
10 1326585C1 1 SPRING - shield
11 21505R1 3 BALL - 1/2 inch
12 1326583C1 1 RACE - shaft retainer
13 19877R1 3 PIN - dowel, 3/16 x 1/2 inch
14 100-11187 1 Ring, Snap, #187, Ext
19 NSS 1 SHAFT - male, inner
20 NSS 1 YOKE - drive
24 1326580C1 1 COLLAR - yoke
26 211-1016 3 BALL - chrome alloy steel, 1/2 inch, grade 24
28 19877R1 3 PIN - dowel, 3/16 x 1/2 inch
29 100-11187 1 Ring, Snap, #187, Ext
1326747C91 1 SHIELD ASSEMBLY - outer, with decal, Includes: Ref. 35 - 37
36 1326579C1 1 DECAL - lubricate journal and bearing
37 1980787C1 1 BEARING KIT - shield
1326750C91 1 SHIELD ASSEMBLY - inner, Includes: Ref. 39 & 40
39 1326593C1 1 SHIELD - inner
9B-30 KNIFE DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER (BONDIOLI AND PAVESI)
9B-30 KNIFE DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER (BONDIOLI AND PAVESI)

1 1313570C92 1 SHAFT ASSEMBLY - drive, auger (With decals), Includes: Ref. 2 - 32
2 NSS 1 TUBE - outer
4 Q2937 1 PIN, LOCK, M8 x 55, Slotted
14 838-5845 1 PIN - roll, 8 x 45 mm
26 1326628C91 1 SHIELD ASSEMBLY - outer, Includes: Ref. 27
28 1326631C91 1 SHIELD ASSEMBLY - inner, Includes: Ref. 29
29 1544650C1 1 BEARING - shield
30 1326625C91 2 SHIELD ASSEMBLY - yoke, Includes: Ref. 31
9B-32 KNIFE DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER (WALTERSHEID)
9B-32 KNIFE DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER (WALTERSHEID)

1316215C91 1 SHAFT - drive, Includes: Ref. 2 - 21
2 1326494C1 2 SHIELD - drive shaft
3 1326500C1 2 COLLAR - drive shaft
4 1326498C1 4 RING - outer
5 1326499C1 2 BEARING - ball
6 1326490C1 2 YOKE ASSEMBLY - drive shaft, Includes: Ref. 7
7 1281458C1 1 KIT - pin
8 1281444C1 2 KIT - cross and bearing, drive shaft
11 1281445C1 1 YOKE - end, male
12 30907R1 2 PIN - slotted spring, 10 x 70 mm
13 1326491C1 1 TUBE - drive shaft, inner
14 1326495C1 2 FLANGE - guard
15 1281450C1 2 RING - bearing
18 1326492C1 1 TUBE - drive shaft, outer
19 1326493C1 1 YOKE - end, female
20 1326497C1 1 TUBE - shield, inner
21 1281453C1 1 CHAIN - anti-rotation
9B-34 KNIFE DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER (HAYES-DANA)
9B-34 KNIFE DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER (HAYES-DANA)

1316989C91 1 SHAFT ASSEMBLY - drive, header (With decals), Includes: Ref. 3 - 40
3 NSS 1 TUBE - female, outer
4 NSS 1 YOKE - outer
9 1326580C1 1 COLLAR - yoke
11 21505R1 3 BALL - 1/2 inch
13 19877R1 3 PIN - dowel, 3/16 x 1/2 inch
14 100-11187 1 Ring, Snap, #187, Ext
19 NSS 1 SHAFT - male, inner
20 NSS 1 YOKE - drive
24 1326580C1 1 COLLAR - yoke
26 21505R1 3 BALL - 1/2 inch
28 19877R1 3 PIN - dowel, 3/16 x 1/2 inch
29 100-11187 1 Ring, Snap, #187, Ext
1326746C91 1 SHIELD ASSEMBLY - outer, with decal, Includes: Ref. 35 - 37
35 NSS 1 SHIELD - outer
36 1326579C1 1 DECAL - lubricate journal and bearing
1326749C91 1 SHIELD ASSEMBLY - inner, Includes: Ref. 39 & 40
39 NSS 1 SHIELD - inner
9C-02 AUGER
9C-02 AUGER

1 106001A2 1 AUGER - (15.0 foot)
1 106002A2 1 AUGER - (16.5 foot)
1 106003A2 1 AUGER - (17.5 foot)
1 106004A2 1 AUGER - (20.0 foot)
1 106005A2 1 AUGER - (22.5 foot)
1 106006A2 1 AUGER - (25.0 foot)
1 106007A2 1 AUGER - (30.0 foot)
2 106024A1 1 SHAFT ASSEMBLY - drive
3 426-616 12 BOLT, Hex, 3/8"-16 x 1", G8, Full Thd
4 429-106 12 NUT - hex, 3/8 inch NC, grade 8
5 492-11038 12 3/8"
6 25534R1 12 WASHER - flat, 13/32 x 13/16 x 1/16 inch
7 1307256C1 1 RETAINER - auger LH
8 664073R92 2 BEARING - ball, auger shaft
9 455112R11 2 COLLAR - locking, bearing (With set screw)
10 663562R1 4 FLANGE - bearing, round (Alternate with 1307583C1)
10 1307583C1 4 FLANGE - bearing, square (Alternate with 663562R1)
13 232-5318 8 NUT, LOCK, Flg, 1/2"-13
14 204807C91 1 BEARING - ball, auger shaft inner
15 455102R21 1 COLLAR - locking, bearing, includes set screw
16 937517R1 2 FLANGE - bearing
17 231-5315 3 NUT, LOCK, Flg, 5/16"-18
18 1307262C1 1 TUBE - finger adjusting (15.0 foot)
19 1307267C1 1 TUBE - finder adjusting (30.0 foot)
20 184505C1 2 COVER - handhole
22 REF 1 SHAFT ASSEMBLY - finger, See Figure 9C-04
9C-04 AUGER FINGERS
9C-04 AUGER FINGERS

1 1307259C2 18 GUIDE - finger
2 413-48 36 BOLT - hex, 1/4 NC x 1/2 inch
3 127550 36 NUT - special, 1/4 inch NC
4 1320699C1 18 FINGER - retractable
5 185309A1 18 PIN - hair, quick attachable
6 1308425C1 20 HUB - finger
7 1316383C1 1 SHAFT - finger
8 1326467C1 1 BAR - finger shaft clamp
12 1320698C1 1 ANGLE - finger drive shaft
9C-06 AUGER FLIGHT EXTENSION
9C-06 AUGER FLIGHT EXTENSION

1 1308445C2 1 EXTENSION - auger flight, left-hand
2 1308446C2 1 EXTENSION - auger flight, right-hand
6 167823C1 2 COVER - finger hole
7 413-412 4 BOLT - hex, 1/4 NC x 3/4 inch
8 231-4144 4 NUT, LOCK, 1/4"-20, GB
9C-08 AUGER SUPPORTS
9C-08 AUGER SUPPORTS

1 106041A1 1 BRACKET ASSEMBLY - auger, left-hand, Includes: Ref. 2
2 189971C1 1 BUSHING - pivot
3 1968840C1 2 SPACER - 3/4 OD x 1-1/16 inch, auger pivot
4 413-832 2 BOLT - hex, 1/2 NC x 2 inch
5 232-5318 2 NUT, LOCK, Flg, 1/2"-13
8 128429A2 1 BRACKET ASSEMBLY - auger, right-hand, Includes: Ref. 9
13 128199A1 1 SUPPORT - auger adjusting, left-hand
14 133822A1 1 SUPPORT - auger adjusting, right-hand
15 425-108 8 NUT - hex, 1/2 inch NC
16 1320723C1 2 SUPPORT - auger lift
17 480523R1 2 PIN - hair
18 432-1218 2 3/16" x 1 1/8"
19 439-5844 2 PIN - headed, 1/2 x 2-3/4 inch
20 127870A1 2 BOLT - eye, auger pivot
23 664073R92 1 BEARING - ball, drive shaft
24 663562R1 2 FLANGE - bearing, round (Alternate with 1307583C1)
24 1307583C1 2 FLANGE - bearing, square (Alternate with 663562R1)
27 1320695C1 1 TUBE - finger adjusting, inner
28 1307195C2 1 U-BOLT - 1/2 inch NC
9C-10 AUGER DRIVE
NOTE: With Auger Drive Sprocket (Ref. 2), Use Bulk Chain 611362R91, Connecting Link 574532R91 And Roller Link 241-1116 In The
Following Quantities: NOTE: 56 Tooth Sprocket - 85 Chain Links, 2 Connecting Links And 1 Roller Link. 50 Tooth Sprocket - 83 Chain
Links And 1 Connecting Link. 45 Tooth Sprocket - 81 Chain Links And 1 Connecting Link. 40 Tooth Sprocket - 79 Chain Links And 1
Connecting Link.
9C-10 AUGER DRIVE

1 NSS 1 CHAIN ASSEMBLY - auger drive, With Auger Drive Sprocket (Ref. 2), Use Bulk Chain 611362R91,
Connecting Link 574532R91 And Roller Link 241-1116 In The Following Quantities: 56 - Tooth
Sprocket - 85 Chain Links, 2 Connecting Links And 1 Roller Link. 50 Tooth Sprocket - 83 Chain Links
And 1 Connecting Link. 45 Tooth Sprocket - 81 Chain Links And 1 Connecting Link. 40 Tooth
Sprocket - 79 Chain Links And 1 Connecting Link.
2 106055A1 1 SPROCKET - auger drive, 152 RPM, 56 tooth (Standard)
2 106056A1 1 SPROCKET - auger drive, 170 RPM, 50 tooth (Optional)
3 496-21106 1 WASHER - flat, 1-1/16 x 2 x 13/64 inch, hardened
4 425-1416 2 NUT - hex, jam, 1 inch NC
5 125966A1 1 HUB - auger drive sprocket
6 413-832 2 BOLT - hex, 1/2 NC x 2 inch
7 425-108 2 NUT - hex, 1/2 inch NC
8 125990A1 1 SPROCKET - auger drive, 17 tooth
9 1319250C1 4 BOLT - hex flange, special, 3/8 NC x 1 inch
10 179013A1 1 SPROCKET - idler, 15 tooth
11 413-836 1 BOLT - hex, 1/2 NC x 2-1/4 inch
12 131-943 1 NUT, Flg, 1/2"-13, G5
13 495-11053 3 WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
14 128261A3 1 BRACKET - idler sprocket
15 413-820 1 BOLT - hex, 1/2 NC x 1-1/4 inch
16 131-943 1 NUT, Flg, 1/2"-13, G5
17 495-81213 2 WASHER - flat, 1-13/32 x 2 x 3/64 inch
NOTE: With Auger Drive Sprocket (Ref. 2), Use Bulk Chain 611362R91, Connecting Link 574532R91 And Roller Link 241-1116 In The
Following Quantities: NOTE: 56 Tooth Sprocket - 85 Chain Links, 2 Connecting Links And 1 Roller Link. 50 Tooth Sprocket - 83 Chain
Links And 1 Connecting Link. 45 Tooth Sprocket - 81 Chain Links And 1 Connecting Link. 40 Tooth Sprocket - 79 Chain Links And 1
Connecting Link.
9C-12 AUGER DRIVE SHIELD AND SUPPORTS
9C-12 AUGER DRIVE SHIELD AND SUPPORTS

1 1316566C3 1 SHIELD - auger drive
2 1326230C1 1 HINGE - shield, auger drive
3 1326408C2 1 STUD - fastener, shield
4 1326407C1 2 RETAINER - shield stud
7 231-5144 8 NUT, Flg, USR, 1/4"-20
9 1316721C1 1 SUPPORT - auger shield, front
11 231-5146 2 NUT, Flg, USR, 3/8"-16
9C-14 AUGER JACKSHAFT DRIVE, 15.0 AND 16.5 FOOT HEADER

2 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
4 REF 1 DRIVE SHAFT ASSEMBLY - auger, See Figure 9C-22
5 106023A2 1 SHIELD - clutch
7 231-5144 2 NUT, Flg, USR, 1/4"-20
12 231-5146 6 NUT, Flg, USR, 3/8"-16
13 106084A2 1 SUPPORT - jackshaft
15 231-5146 2 NUT, Flg, USR, 3/8"-16
16 106087A1 1 SHIELD - cover
17 183-123 2 SCREW - thumb with shoulder, 5/16 NC x 3/4 inch
18 488837C1 2 NUT - speed, 5/16 inch
25 425-108 2 NUT - hex, 1/2 inch NC

2 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
7 231-5144 2 NUT, Flg, USR, 1/4"-20
13 231-5146 9 NUT, Flg, USR, 3/8"-16
18 231-5148 1 NUT, Flg, USR, 1/2"-13
34 425-108 2 NUT - hex, 1/2 inch NC

2 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
7 231-5144 2 NUT, Flg, USR, 1/4"-20
12 231-5146 6 NUT, Flg, USR, 3/8"-16
15 409-1512 2 BOLT - hex, self-locking, 5/16 NC x 3/4 inch
30 425-108 2 NUT - hex, 1/2 inch NC
9C-20 AUGER JACKSHAFT DRIVE, 30.0 FOOT HEADER
9C-20 AUGER JACKSHAFT DRIVE, 30.0 FOOT HEADER

2 413-840 1 BOLT - hex, 1/2 NC x 2-1/2 inch
7 231-5144 2 NUT, Flg, USR, 1/4"-20
13 231-5146 9 NUT, Flg, USR, 3/8"-16
21 231-5148 1 NUT, Flg, USR, 1/2"-13
22 409-1512 2 BOLT - hex, self-locking, 5/16 NC x 3/4 inch
35 425-108 2 NUT - hex, 1/2 inch NC
9C-22 AUGER DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER
9C-22 AUGER DRIVE SHAFT, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER

1 106044A1 1 SHAFT ASSEMBLY - auger drive, with decals, Includes: Ref. 2 - 30
106108A1 1 SHAFT ASSEMBLY - female drive, Includes: Ref. 2 - 9
106110A1 1 SHAFT ASSEMBLY - male drive, Includes: Ref. 10 - 18
12 838-5845 1 PIN - roll, 8 x 45 mm
16 106089A1 1 CLUTCH ASSEMBLY - drive shaft, See Figure 9C-28
25 106104A1 1 SHIELD ASSEMBLY - outer, Includes: Ref. 26
27 106106A1 1 SHIELD ASSEMBLY - inner, Includes: Ref. 29
28 1326625C91 1 SHIELD ASSEMBLY - yoke, outer, Includes: Ref. 29
30 1326632C1 2 CHAIN - drive shaft, safety
9C-24 AUGER DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER
9C-24 AUGER DRIVE SHAFT, 22.5, 25.0 AND 30.0 FOOT HEADER

1 106043A1 1 SHAFT ASSEMBLY - auger drive, with decals, Includes: Ref. 2 - 30
106107A1 1 SHAFT ASSEMBLY - female drive, Includes: Ref. 2 - 9
106109A1 1 SHAFT ASSEMBLY - male drive, Includes: Ref. 10 - 18
12 Q2937 1 PIN, LOCK, M8 x 55, Slotted
16 106089A1 1 CLUTCH ASSEMBLY - drive shaft, See Figure 9C-28
25 106103A1 1 SHIELD ASSEMBLY - outer female shaft, Includes: Ref. 26
27 106105A1 1 SHIELD ASSEMBLY - inner, Includes: Ref. 29
28 1326625C91 1 SHIELD ASSEMBLY - yoke, outer, Includes: Ref. 29
9C-26 FEEDER JACKSHAFT, 1420, 1440, 1460 AND 1480 COMBINE
For Combines With Feeder Jackshaft Without Machined Groove 1 Inch From End (1982 Season And Prior).
9C-26 FEEDER JACKSHAFT, 1420, 1440, 1460 AND 1480 COMBINE

1 184596C2 1 SHAFT - feeder jackshaft (1420 Combine)
2 195560C3 1 SHAFT - feeder jackshaft (1440 and 1460 Combine)
3 195559C3 1 SHAFT - feeder jackshaft (1480 Combine)
For Combines With Feeder Jackshaft Without Machined Groove 1 Inch From End (1982 Season And Prior).
9C-28 CLUTCH - DRIVE SHAFT
9C-28 CLUTCH - DRIVE SHAFT

1 106089A1 1 CLUTCH ASSEMBLY - drive shaft, Includes: Ref. 2 - 11
2 224579A1 1 HOUSING - slip clutch
3 224587A1 1 YOKE - flange cover
4 224585A1 1 HUB ASSEMBLY, Includes: Ref. 5
5 1311950C1 1 KIT - push pin
6 224584A1 2 PLATE - friction
7 224582A1 1 PLATE - pressure
8 224643A1 1 DISC - internal
9 224581A1 1 WASHER - Belleville
10 224580A1 1 RING - retaining
11 861-8020 8 BOLT - hex socket, 8 - 1.25 x 20 mm, class 12.9
9D-02 MAIN FRAME, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER
9D-02 MAIN FRAME, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER

1 133209A1 1 BEAM ASSEMBLY - main, with decals (15.0 foot)
3 1307374C5 1 POST - vertical, left-hand
4 1307375C5 1 POST - vertical, right-hand
7 232-5138 30 NUT, Flg, USR, 1/2"-13, G8
8 1326056C92 1 SHEET ASSEMBLY - rear, left-hand, with decals (15.0 foot)
10 1326057C93 1 SHEET ASSEMBLY - rear, right-hand, with decals (15.0 foot)
11 133973A1 4 ANGLE - chain
16 135370A1 1 TRIM - edge, 7-5/8 inch (194 mm) long, cut from 1330108CX bulk trim, lift cylinder hose, front
17 87435C1 1 TRIM - edge, 3 inch (76 mm) long, cut from 1330108CX bulk trim, lift cylinder hose, rear
18 326-820 2 BOLT, Hex, 1/2"-13 x 1 1/4", G8, Full Thd
25 281-14812 UAR SCREW - self-tapping, hex washer head, 5/16 NC x 3/4 inch
28 131176A1 1 SHEET - end, left-hand
29 130817A1 1 SHEET - end, right-hand
31 1313966C1 2 BAR - shim
34 231-5146 24 NUT, Flg, USR, 3/8"-16
9D-04 MAIN FRAME, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (CONT'D)
9D-04 MAIN FRAME, 15.0, 16.5, 17.5 AND 20.0 FOOT HEADER (CONT'D)

45 1307500C94 1 BEAM ASSEMBLY - lower (15.0 foot), Includes: Ref. 46 & 47
47 206321H1 1 Ring, Snap, 1.625", Int, #162
49 1316564C1 2 ANGLE - stripper extension
50 189825C2 UAR BAR - auger stripper, adjustable
52 434-512 UAR BOLT - carriage, 5/16 NC x 3/4 inch
54 232-5318 4 NUT, LOCK, Flg, 1/2"-13
58 1307371C1 2 BAR - feeder latch
59 177134C3 2 U-BOLT - feeder latch
9D-06 MAIN FRAME, 22.5, 25.0 AND 30.0 FOOT HEADER
9D-06 MAIN FRAME, 22.5, 25.0 AND 30.0 FOOT HEADER

1 133213A1 1 BEAM - main, with decals (22.5 foot)
3 1307374C5 1 POST - vertical, left-hand
4 1307375C5 1 POST - vertical, right-hand
5 1307376C4 1 POST - intermediate, left-hand
5 128414A2 1 POST - intermediate, right-hand
6 409-7816 20 BOLT - hex serrated flange, 1/2 NC x 1 inch (22.5 foot)
6 1302143C1 20 BOLT - hex flange, special, 1 inch
7 232-5138 54 NUT, Flg, USR, 1/2"-13, G8
9 326-820 2 BOLT, Hex, 1/2"-13 x 1 1/4", G8, Full Thd
12 1307093C1 1 SHEET - rear, left-hand, with decals (22.5 foot)
14 1307094C1 1 SHEET - rear, right-hand, with decals (22.5 foot)
17 1326062C92 1 SHEET - center rear, left-hand, with decals
20 1326063C93 1 SHEET - center rear, right-hand, with decals
25 281-14812 UAR SCREW - self-tapping, hex washer head, 5/16 NC x 3/4 inch
28 131176A1 1 SHEET - end, left-hand
29 130817A1 1 SHEET - end, right-hand
31 1313966C1 2 BAR - shim
34 231-5146 18 NUT, Flg, USR, 3/8"-16
35 133973A1 4 ANGLE - chain
38 135370A1 1 TRIM - edge, 194 mm (7-5/8 inch) long, cut from 1330108CX bulk trim, lift cylinder hose, front
39 87435C1 1 TRIM - edge, 76 mm (3 inch) long, cut from 1330108CX bulk trim, lift cylinder hose, rear
47 100-28162 1 Ring, Snap, 1.625", Int, #162
1313980C91 ASSEMBLY inner, weldment
9D-08 MAIN FRAME, 22.5, 25.0 AND 30.0 FOOT HEADER (CONT'D)
9D-08 MAIN FRAME, 22.5, 25.0 AND 30.0 FOOT HEADER (CONT'D)

49 1316564C1 2 ANGLE - stripper extension
50 189825C2 UAR BAR - auger stripper, adjustable
52 434-512 UAR BOLT - carriage, 5/16 NC x 3/4 inch
54 231-5148 17 NUT, Flg, USR, 1/2"-13
58 1307371C1 2 BAR - feeder latch
59 177134C3 2 U-BOLT - feeder latch
9D-10 MAIN FRAME SUPPORTS

1 1313979C91 1 SUPPORT ASSEMBLY - pivot, outer, Includes: Ref. 2 & 3
3 206321H1 1 Ring, Snap, 1.625", Int, #162
5 199408C1 UAR SHIM - .032 inch, support
7 231-5148 UAR NUT, Flg, USR, 1/2"-13
8 128452A2 1 SUPPORT - runner, left hand, (For #8) weldment for the inner pivot assembly is 1313980c91 dmm
10/1/97
9 1316828C1 1 SPACER - support
10 232-41110 2 NUT, LOCK, 5/8"-11, GC
11 130867A1 1 STRAP - down stop, left-hand
14 495-11053 UAR WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
18 480523R1 2 PIN - hair
19 1989223C3 UAR SUPPORT - runner, inner
20 577715R1 UAR SPACER - 7/8 x 3/8 inch
22 495-81177 UAR WASHER - flat, 21/32 x 1 x 1/32 inch
23 232-41110 UAR NUT, LOCK, 5/8"-11, GC
24 1316681C1 UAR SUPPORT - runner
30 1316302C1 UAR ARM - stop
31 23173R1 UAR PIN - clevis, 1/2 x 2-3/4 inch
32 432-1216 UAR 3/16" x 1"
33 432-816 UAR 1/8" x 1"
34 1316677C2 1 SUPPORT ASSEMBLY - runner, right-hand, Includes: Ref. 35
35 551068R1 2 BUSHING - concave control housing
36 1316883C2 1 SPACER - 5/8 x 5 inch
37 413-1096 1 BOLT - hex, 5/8 NC x 6 inch
38 232-41110 1 NUT, LOCK, 5/8"-11, GC
39 137928A1 1 SUPPORT - spring, left-hand
41 413-836 1 BOLT - hex, 1/2 NC x 2-1/4 inch
42 610399R1 1 SPACER - 1/2 x 7/8 inch
43 495-11053 1 WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
45 1313103C1 1 SPRING - left
46 1313104C1 1 PLUG - spring, lower
47 439-5832 1 PIN - headed, 1/2 x 2 inch
48 432-1216 1 3/16" x 1"
49 124366A1 1 PLUG - spring, upper
50 124365A1 1 BOLT - hex, special, 1/2 NC x 10 inch
52 425-1010 1 NUT, 5/8"-11, G5

54 414077C1 2 BOLT - hex flange, special, 5/8 NC x 1-3/4 inch
55 414089C1 2 NUT - hex flange, special, 5/8 inch NF, grade 8
9D-12 CUTTER BAR SKIDS AND SUPPORT SPRINGS
9D-12 CUTTER BAR SKIDS AND SUPPORT SPRINGS

1 128512A1 1 SUPPORT - skid, left-hand (15.0, 20.0, 25.0 and 30.0 foot)
1 128514A1 1 SUPPORT - skid, left-hand (16.5, 17.5 and 22.5 foot)
3 232-5318 2 NUT, LOCK, Flg, 1/2"-13
4 1307399C3 UAR SKID - cutter bar, #4/5---the wear plate that goes on these two items is part 244860a1. 10/7/97
5 1307398C4 1 SKID - runner support (16.5, 17.5 and 22.5 foot), #4/5---the wear plate that goes on these two items is
part 244860a1. 10/7/97
7 231-5146 UAR NUT, Flg, USR, 3/8"-16
10 1316335C5 1 SKID - runner support, right-hand (15.0, 20.0, 25.0 and 30.0 foot)
12 231-5146 4 NUT, Flg, USR, 3/8"-16
13 1307466C3 UAR SKID - spring support
14 1320908C2 UAR TUBE - cutter bar, lockout
15 1320914C2 2 TUBE - cutter bar (15.0 foot)
15 1320911C2 2 TUBE - cutter bar (16.5 and 22.5 foot)
17 232-5316 UAR NUT - hex flange, self-locking, 3/8 inch NC
18 1307469C1 UAR SPRING - cutter bar support
19 1307468C2 1 SPRING - cutter bar support, right-hand
22 1316387C1 UAR BAR - spring support
23 1305054C2 UAR BAR - spring adjusting
24 1313175C1 UAR BOLT - special, 1/2 NC x 6-1/4 inch, grade 8
25 425-128 UAR NUT - hex, slotted, 1/2 inch NC
26 19674R1 UAR Pin, 3/32" x 1", Coiled
27 396-21053 UAR WASHER - flat, 17/32 x 1-1/16 x 1/8 inch, hardened
29 232-4115 UAR NUT, LOCK, 5/16"-18, GC
9D-14 AUXILIARY CUTTER BAR SKIDS
Quantities Shown Are Per Row.

9D-14 AUXILIARY CUTTER BAR SKIDS

1 1970379C2 3 SKID - cutter bar, auxiliary
2 1970431C1 3 SUPPORT - skid, auxiliary
3 1977119C1 1 BAR - skid support
5 180151 4 BOLT - hex, special, 7/16 NC x 1-3/4 inch
6 1313463C1 6 NUT - hex small flange lock, 7/16 inch NC
8 420-2620 6 BOLT - plow, 3/8 NC x 1-1/4 inch
9 231-5146 12 NUT, Flg, USR, 3/8"-16
Quantities Shown Are Per Row.

9D-16 BOTTOM SHIELDS
9D-16 BOTTOM SHIELDS

1 1313156C2 1 SHIELD - center, bottom
2 1313132C2 1 SHIELD - left-hand, bottom, (15.0 foot)
3 1313138C2 1 SHIELD - right-hand, bottom, (15.0 foot)
4 1307580C1 UAR CLIP - shield retaining
8 231-5144 UAR NUT, Flg, USR, 1/4"-20
9D-18 DIVIDERS
9D-18 DIVIDERS

1 1316060C4 1 DIVIDER - header, left-hand
2 1316061C1 1 DIVIDER - header, right-hand
3 1316709C1 2 CLAMP - wing
6 1316847C2 1 BRACKET - guard support
9 480556C1 2 BOLT - hex, special, 1/2 NC x 8 inch
11 1316731C1 2 PLUG - spring
12 1316732C1 2 SPRING - divider pivot
13 425-108 2 NUT - hex, 1/2 inch NC
16 1316585C1 2 SUPPORT - divider pivot
20 326-1036 2 BOLT, Hex, 5/8"-11 x 2 1/4", G8
22 425-1010 2 NUT, 5/8"-11, G5
23 439-51224 2 PIN - headed, 3/4 x 1-1/2 inch
24 1978738C1 2 PIN - cotter, hair, 3/16 inch
27 1316787C92 1 LEVER ASSEMBLY - divider pivot, right-hand, Includes: Ref. 29 & 30
28 136881A1 1 LEVER ASSEMBLY - divider pivot, left-hand, Includes: Ref. 29 & 30
29 559317R1 1 BUSHING - pivot
30 219-93 1 FITTING - grease, 90 degree, 1/4-28 special taper x 3/4 inch
31 1326465C2 2 SPACER - link pivot
32 413-848 2 BOLT - hex, 1/2 NC x 3 inch
37 140387A1 1 SUPPORT ASSEMBLY - divider, left-hand, Includes: Ref. 38
38 1280291C1 4 BUSHING - 3/4 inch (19 mm) diameter, pivot
43 1316782C1 3 BUSHING - divider pivot
45 498-81006 6 WASHER - flat, square hole, 17/32 x 1-1/4 x 1/8 inch
47 1316322C92 1 SUPPORT ASSEMBLY - divider, right-hand, Includes: Ref. 48
48 1280291C1 2 BUSHING - 3/4 inch (19 mm) diameter, pivot
50 231-5148 4 NUT, Flg, USR, 1/2"-13
52 231-5146 2 NUT, Flg, USR, 3/8"-16
53 1316674C2 1 BRACKET - downstop, right-hand
54 495-11053 2 WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
9D-18 DIVIDERS

55 432-816 2 1/8" x 1"
9D-20 WING DIVIDERS AND ROD DIVIDERS
9D-20 WING DIVIDERS AND ROD DIVIDERS

1 1316197C2 2 SUPPORT - wing, upper
2 477-73116 8 BOLT - serrated slotted truss head, 5/16 NC x 1 inch
4 1307691C1 2 TUBE - wing, lower
5 1307692C2 2 TUBE - wing, upper
6 413-524 2 BOLT - hex, 5/16 NC x 1-1/2 inch
7 413-632 2 BOLT - hex, 3/8 NC x 2 inch
8 232-4115 2 NUT, LOCK, 5/16"-18, GC
13 1307688C2 6 SUPPORT - tube
16 1313163C1 4 BRACKET - support
17 1313164C1 4 U-BOLT - bracket
19 1316772C2 2 SUPPORT - wing, inner
20 1316826C1 2 PIPE - wing support, inner
21 1316773C2 2 SUPPORT - wing, outer
22 1307693C1 2 PIPE - wing support, outer
23 413-524 4 BOLT - hex, 5/16 NC x 1-1/2 inch
24 232-4115 4 NUT, LOCK, 5/16"-18, GC
25 1316201C1 2 SUPPORT - wing
26 1316649C1 2 POINT - wing
29 1307689C1 4 TUBE - wing, inner
33 1307684C1 2 CLAMP - tine
35 231-4144 4 NUT, LOCK, 1/4"-20, GB
36 140649A1 2 SUPPORT - divider
37 131686A1 2 ROD - divider
38 164191C1 2 SCREW - slotted truss head, 5/16 NC x 1-1/2 inch
40 700121908 2 SPACER - pipe, 1/4 x 3/8 inch
9D-22 HEADER HEIGHT CONTROL

1 1320298C3 1 TUBE - sensor, left-hand (15.0 foot)
2 1307604C2 1 TUBE - sensor, right-hand (15.0 foot)
2 1307609C2 1 TUBE - sensor, right-hand (30.0 foot), item # 2, if looking for upgrading spring kit, order p/n 341196A1
3 1316388C1 1 ARM - connector
4 413-528 2 BOLT - hex, 5/16 NC x 1-3/4 inch
5 232-4115 2 NUT, LOCK, 5/16"-18, GC
6 1307610C2 UAR SUPPORT - height control
7 567987R1 UAR SPACER - 5/8 x 11/16 inch, if used
9 9411655 UAR NUT - hex, self-locking, 3/8 inch NC
10 1313081C1 UAR BUSHING - pivot
13 126339A1 1 ROD - indicator, no longer available order 126339A2
13 126339A2 1 ROD - indicator
14 1316572C1 1 PLUG - beveled
15 413-440 1 BOLT - hex, 1/4 NC x 2-1/2 inch
17 1326543C1 1 CAP - indicator end
18 1308482C1 1 COLLAR - sensing tube
19 483-1254 1 SCREW - set, hex socket headless, 1/4 NC x 1/4 inch, cup pt
20 1320312C1 1 BRACKET - cable anchor
22 127360A2 1 POTENTIOMETER - height control
22 1301147C91 1 POTENTIOMETER - height control (For 1400 series combines with electrohydraulics)
26 L18337 1 STRAP - tie, 15 inch, nylon
27 1968782C1 1 ARM - potentiometer control, powdered metal (Alternate with 131175A1)
27 131175A1 1 ARM - potentiometer control, molded plastic (Alternate with 1968782C1)
28 483-1084 1 SCREW - set, hex socket headless, No. 8 NC x 1/4 inch, cup point
29 1316427C3 1 CABLE - control
30 148151 1 CLIP - control cable
32 432-48 2 1/16" x 1/2"
33 427-3058 1 PIN, CLEVIS, 3/16" x .580", Hardened
34 22906R1 1 PIN, HEADED, 1/4" x 3/4"
35 1308301C1 1 BRACKET - mounting

38 1308299C3 1 STRAP - potentiometer mounting
39 1320313C1 1 SUPPORT - linkage shield
40 434-512 1 BOLT - carriage, 5/16 NC x 3/4 inch
41 185230A1 UAR SUPPORT - height control, if used
42 189956A1 1 SPACER - support, if used
9D-24 AUTOMATIC HEADER HEIGHT CONTROL, 1420, 1440, 1460 AND 1480 COMBINE W/O ELECTROHYDRAULICS
9D-24 AUTOMATIC HEADER HEIGHT CONTROL, 1420, 1440, 1460 AND 1480 COMBINE W/O ELECTROHYDRAULICS

1 1320304C1 1 LEVER - linkage arm
2 487704R1 1 SPACER - 3/4 x 1-3/16 inch
3 185062R1 1 BUSHING - spacer
5 495-11053 1 WASHER, 1/2", SAE (17/32" x 1-1/16" x 3/32")
6 413-836 1 BOLT - hex, 1/2 NC x 2-1/4 inch
7 231-5148 1 NUT, Flg, USR, 1/2"-13
12 188981C91 2 CLEVIS - with clip
13 1320308C1 1 STUD - linkage rod
14 425-114 2 NUT, 1/4"-28, G5
15 27825R1 2 SPACER, 1/2" Tube x 1/2"
18 1308301C1 1 BRACKET - mounting
19 1320313C1 1 SUPPORT - linkage shield
20 434-512 1 BOLT - carriage, 5/16 NC x 3/4 inch
9D-26 FEEDER FACE DEFLECTOR, 1420, 1440, 1460 AND 1480 COMBINES
Feeder Face Deflector Not Required If Combine Was Previously Equipped With 810 Grain Header And 600 mm Auger.
9D-26 FEEDER FACE DEFLECTOR, 1420, 1440, 1460 AND 1480 COMBINES

1 184853C1 1 DEFLECTOR - front, left-hand
2 184854C1 1 DEFLECTOR - front, right-hand
5 181669C1 1 COVER - feeder adapter (1480 Combine)
5 1319220C1 1 COVER - feeder adapter (1420, 1440 and 1460 Combines)
Feeder Face Deflector Not Required If Combine Was Previously Equipped With 810 Grain Header And 600 mm Auger.
9D-28 DECALS, ENGLISH LANGUAGE, FRENCH LANGUAGE, SPANISH LANGUAGE, GERMAN LANGUAGE, ITALIAN LANGUAGE

1 1316998C2 1 DECAL - 1020, model number
2 1326215C1 2 DECAL - warning, keep drive line shields in place
3 1320694C3 2 DECAL - danger, rest the header on the ground
4 144385A1 2 DECAL - warning, shields are provided to guard
5 179245C1 1 DECAL - lubrication - 10 hours
6 179246C1 6 DECAL - lubrication - 50 hours
7 179244C1 4 DECAL - lubrication - 100 hours, if used
8 1316995C1 2 DECAL - warning, avoid serious injury, if usedl
10 185067A1 2 DECAL - warning, avoid injury, always lock both reel lift cylinders
2 1326216C1 1 DECAL - warning, keep drive line shields in place (French) language
3 1323199C2 2 DECAL - danger, rest the header on the ground (French) language
4 182191A2 2 DECAL - warning, shields are provided to guard these moving parts, French language
8 1326079C1 2 DECAL - warning, avoid serious injury (French), if used, language
10 185298A1 2 DECAL - warning, avoid injury, always lock both reel lift cylinders (French) language
10 185791A1 2 DECAL - warning, avoid injury, always lock both reel lift cylinders (Quebec) French language
2 1326217C1 1 DECAL - warning, keep drive line shields in place (Spanish) language
3 1323197C2 2 DECAL - danger, rest the header on the ground (Spanish) language
4 182192A2 2 DECAL - warning, shields are provided to guard these moving parts, Spanish language
8 1326080C1 2 DECAL - warning, avoid serious injury (Spanish), if used, language
10 185296A1 2 DECAL - warning, avoid injury, always lock both reel lift cylinders (Spanish) language
2 1326218C1 1 DECAL - warning, keep drive line shields in place (German) language
3 1323198C2 2 DECAL - danger, rest the header on the ground (German) language
4 1326078C1 2 DECAL - warning, shields are provided to guard (German) language
8 1326081C1 2 DECAL - warning, avoid serious injury (German), if used, language
10 185297A1 2 DECAL - warning, avoid injury, always lock both reel lift cylinders (German) language
2 103284A1 1 DECAL - warning, keep drive line shields in place (Italian) language
3 1345444C2 2 DECAL - danger, rest the header on the ground (Italian) language
4 1345445C1 2 DECAL - warning, shields are provided to guard (Italian) language
8 103287A1 2 DECAL - warning, avoid serious injury (Italian), if used, language
10 189990A1 2 DECAL - warning, avoid injury, always lock both reel lift cylinders (Italian), replaces 103286A1, languag

13 197105C2 1 DECAL - important, do not overlube, if used
14 1326072C1 2 DECAL - important, place auger lift link in rear hole
15 1284374C1 2 REFLECTOR - red
15 1284365C2 2 REFLECTOR - amber
17 1326519C1 2 DECAL - important, readjust auger idler, if used
18 1326523C1 1 DECAL - important, to adjust auger chain idler, if used
19 1326528C1 3 DECAL - danger, shield missing, do not operate
20 1326752C1 1 DECAL - lubrication instructions
21 1326579C1 1 DECAL - lubricate journal and bearing, if used
24 1326618C1 1 DECAL - drive identification
25 1326619C1 1 DECAL - fore/aft detent, if used
26 182142C1 1 DECAL - important, clean dirt from top of skids
27 1313194C1 1 DECAL - header height, if used
28 106081A1 1 DECAL - header height, if used
29 137708A1 1 DECAL - header height
13 1323213C1 1 DECAL - important, do not overlube (French), if used, language
14 1326073C1 2 DECAL - important, place auger lift link in rear hole (French) language
17 1326520C1 2 DECAL - important, readjust auger idler (French), if used, language
18 1326524C1 1 DECAL - important, to adjust auger chain idler (French), if used, language
19 1326529C1 2 DECAL - danger, shield missing, do not operate (French), if used, language
26 1323182C1 1 DECAL - important, clean dirt from top of skids (French) language
13 1323211C1 1 DECAL - important, do not overlube (Spanish), if used, language
14 1326074C1 2 DECAL - important, place auger lift link in rear hole (Spanish) language
17 1326521C1 2 DECAL - important, readjust auger idler (Spanish), if used, language
18 1326525C1 1 DECAL - important, to adjust auger chain idler (Spanish), if used, language
19 1326530C1 2 DECAL - danger, shield missing, do not operate (Spanish), if used, language
26 1323180C1 1 DECAL - important, clean dirt from top of skids (Spanish) language
13 1323212C1 1 DECAL - important, do not overlube (German), if used, language
14 1326075C1 2 DECAL - important, place auger lift link in rear hole (German) language
17 1326522C1 2 DECAL - important, readjust auger idler (German), if used, language
18 1326526C1 1 DECAL - important, to adjust auger chain idler (German), if used, language
19 1326531C1 2 DECAL - danger, shield missing, do not operate (German), if used, language
26 1323181C1 1 DECAL - important, clean dirt from top of skids (German) language
13 103288A1 1 DECAL - important, do not overlube (Italian), if used, language
14 103285A1 2 DECAL - important, place auger lift link in rear hole (Italian) language
17 103283A1 2 DECAL - important, readjust auger idler (Italian), if used, language
18 103282A1 1 DECAL - important, to adjust auger chain idler (Italian), if used, language
19 103281A1 2 DECAL - danger, shield missing do not operate (Italian), if used, language
26 103280A1 1 DECAL - important, clean dirt from top of skids (Italian) language

1020 PDF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1020 PDF

Uploaded by

Copyright:

Available Formats

1020 GRAIN HEADER (S/N JJC0215001 TO JJC0227000)

1-01 1020 GRAIN HEADER, P.I.N. JJC0215001 - JJC0227000, PARTS CATALOG

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

1330177C2, pulley is 5" O.D.

Ссылка Номер детали Кол-во Описание

1330177C2, pulley is 5" O.D.

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание

Ссылка Номер детали Кол-во Описание