ISO 286-1:2010(E)

Table 1 — Values of standard tolerance grades for nominal sizes up to 3 150 mm

Nominal size Standard tolerance grades

mm
IT01 IT0 IT1 IT2 IT3 IT4 IT5 IT6 IT7 IT8 IT9 IT10 IT11 IT12 IT13 IT14 IT15 IT16 IT17 IT18

Up to Standard tolerance values

and
Above
inclu- µm mm
ding

— 3 0,3 0,5 0,8 1,2 2 3 4 6 10 14 25 40 60 0,1 0,14 0,25 0,4 0,6 1 1,4

3 6 0,4 0,6 1 1,5 2,5 4 5 8 12 18 30 48 75 0,12 0,18 0,3 0,48 0,75 1,2 1,8

6 10 0,4 0,6 1 1,5 2,5 4 6 9 15 22 36 58 90 0,15 0,22 0,36 0,58 0,9 1,5 2,2

10 18 0,5 0,8 1,2 2 3 5 8 11 18 27 43 70 110 0,18 0,27 0,43 0,7 1,1 1,8 2,7

18 30 0,6 1 1,5 2,5 4 6 9 13 21 33 52 84 130 0,21 0,33 0,52 0,84 1,3 2,1 3,3

30 50 0,6 1 1,5 2,5 4 7 11 16 25 39 62 100 160 0,25 0,39 0,62 1 1,6 2,5 3,9

50 80 0,8 1,2 2 3 5 8 13 19 30 46 74 120 190 0,3 0,46 0,74 1,2 1,9 3 4,6

80 120 1 1,5 2,5 4 6 10 15 22 35 54 87 140 220 0,35 0,54 0,87 1,4 2,2 3,5 5,4

120 180 1,2 2 3,5 5 8 12 18 25 40 63 100 160 250 0,4 0,63 1 1,6 2,5 4 6,3

180 250 2 3 4,5 7 10 14 20 29 46 72 115 185 290 0,46 0,72 1,15 1,85 2,9 4,6 7,2

250 315 2,5 4 6 8 12 16 23 32 52 81 130 210 320 0,52 0,81 1,3 2,1 3,2 5,2 8,1

315 400 3 5 7 9 13 18 25 36 57 89 140 230 360 0,57 0,89 1,4 2,3 3,6 5,7 8,9

400 500 4 6 8 10 15 20 27 40 63 97 155 250 400 0,63 0,97 1,55 2,5 4 6,3 9,7

500 630 9 11 16 22 32 44 70 110 175 280 440 0,7 1,1 1,75 2,8 4,4 7 11

630 800 10 13 18 25 36 50 80 125 200 320 500 0,8 1,25 2 3,2 5 8 12,5

800 1 000 11 15 21 28 40 56 90 140 230 360 560 0,9 1,4 2,3 3,6 5,6 9 14

1 000 1 250 13 18 24 33 47 66 105 165 260 420 660 1,05 1,65 2,6 4,2 6,6 10,5 16,5

1 250 1 600 15 21 29 39 55 78 125 195 310 500 780 1,25 1,95 3,1 5 7,8 12,5 19,5

1 600 2 000 18 25 35 46 65 92 150 230 370 600 920 1,5 2,3 3,7 6 9,2 15 23

2 000 2 500 22 30 41 55 78 110 175 280 440 700 1 100 1,75 2,8 4,4 7 11 17,5 28

2 500 3 150 26 36 50 68 96 135 210 330 540 860 1 350 2,1 3,3 5,4 8,6 13,5 21 33

20 © ISO 2010 – All rights reserved

 ISO 286-1:2010(E)

Table 2 — Values of the fundamental deviations for holes A to M

Fundamental deviation values in micrometres
Nominal size Fundamental deviation values
mm Lower limit deviation, EI Upper limit deviation, ES
Up to Up to
Up to Above and Above
and
and All standard tolerance grades IT6 IT7 IT8
Above includ- IT8 includ- IT8
includ- ing IT8 ing IT8
ing
Aa Ba C CD D E EF F FG G H JS J Kc,d Mb,c,d
— 3 +270 +140 +60 +34 +20 +14 +10 +6 +4 +2 0 +2 +4 +6 0 0 −2 −2
3 6 +270 +140 +70 +46 +30 +20 +14 +10 +6 +4 0 +5 +6 +10 −1 + ∆ −4 + ∆ −4
6 10 +280 +150 +80 +56 +40 +25 +18 +13 +8 +5 0 +5 +8 +12 −1 + ∆ −6 + ∆ −6
10 14
+290 +150 +95 +70 +50 +32 +23 +16 +10 +6 0 +6 +10 +15 −1 + ∆ −7 + ∆ −7
14 18
18 24
+300 +160 +110 +85 +65 +40 +28 +20 +12 +7 0 +8 +12 +20 −2 + ∆ −8 + ∆ −8
24 30
30 40 +310 +170 +120
+100 +80 +50 +35 +25 +15 +9 0 +10 +14 +24 −2 + ∆ −9 + ∆ −9
40 50 +320 +180 +130
50 65 +340 +190 +140
+100 +60 +30 +10 0 +13 +18 +28 −2 + ∆ −11 + ∆ −11
65 80 +360 +200 +150
80 100 +380 +220 +170

Deviations = ± ITn/2, where n is the standard tolerance grade number

+120 +72 +36 +12 0 +16 +22 +34 −3 + ∆ −13 + ∆ −13
100 120 +410 +240 +180
120 140 +460 +260 +200
140 160 +520 +280 +210 +145 +85 +43 +14 0 +18 +26 +41 −3 + ∆ −15 + ∆ −15
160 180 +580 +310 +230
180 200 +660 +340 +240
200 225 +740 +380 +260 +170 +100 +50 +15 0 +22 +30 +47 −4 + ∆ −17 + ∆ −17
225 250 +820 +420 +280
250 280 +920 +480 +300
+190 +110 +56 +17 0 +25 +36 +55 −4 + ∆ −20 + ∆ −20
280 315 +1 050 +540 +330
315 355 +1 200 +600 +360
+210 +125 +62 +18 0 +29 +39 +60 −4 + ∆ −21 + ∆ −21
355 400 +1 350 +680 +400
400 450 +1 500 +760 +440
+230 +135 +68 +20 0 +33 +43 +66 −5 + ∆ −23 + ∆ −23
450 500 +1 650 +840 +480
500 560
+260 +145 +76 +22 0 0 −26
560 630
630 710
+290 +160 +80 +24 0 0 −30
710 800
800 900
+320 +170 +86 +26 0 0 −34
900 1 000
1 000 1 120
+350 +195 +98 +28 0 0 −40
1 120 1 250
1 250 1 400
+390 +220 +110 +30 0 0 −48
1 400 1 600
1 600 1 800
+430 +240 +120 +32 0 0 −58
1 800 2 000
2 000 2 240
+480 +260 +130 +34 0 0 −68
2 240 2 500
2 500 2 800
+520 +290 +145 +38 0 0 −76
2 800 3 150
a Fundamental deviations A and B shall not be used for nominal sizes u 1 mm.
b Special case: for tolerance class M6 in the range above 250 mm up to and including 315 mm, ES = −9 µm (instead of –11 µm according to the
calculation).
c For determining the values K and M, see 4.3.2.5.
d For ∆ values, see Table 3.

© ISO 2010 – All rights reserved 21

22

ISO 286-1:2010(E)
Table 3 — Values of the fundamental deviations for holes N to ZC
Fundamental deviation values and ∆ values in micrometres
Nominal size Fundamental deviation values
mm Values for ∆
Upper limit deviation, ES
Up to
Up to and
Up to and Above Standard tolerance
including Standard tolerance grades above IT7
Above and including IT8 grades
IT7
including IT8
Na,b P to ZCa P R S T U V X Y Z ZA ZB ZC IT3 IT4 IT5 IT6 IT7 IT8
— 3 −4 −4 −6 −10 −14 −18 −20 −26 −32 −40 −60 0 0 0 0 0 0
3 6 −8 + ∆ 0 −12 −15 −19 −23 −28 −35 −42 −50 −80 1 1,5 1 3 4 6
6 10 −10 + ∆ 0 −15 −19 −23 −28 −34 −42 −52 −67 −97 1 1,5 2 3 6 7
10 14 −40 −50 −64 −90 −130
−12 + ∆ 0 −18 −23 −28 −33 1 2 3 3 7 9
14 18 −39 −45 −60 −77 −108 −150

Values as for standard tolerance grades above IT7 increased by ∆

18 24 −41 −47 −54 −63 −73 −98 −136 −188
−15 + ∆ 0 −22 −28 −35 1,5 2 3 4 8 12
24 30 −41 −48 −55 −64 −75 −88 −118 −160 −218
30 40 −48 −60 −68 −80 −94 −112 −148 −200 −274
−17 + ∆ 0 −26 −34 −43 1,5 3 4 5 9 14
40 50 −54 −70 −81 −97 −114 −136 −180 −242 −325
50 65 −41 −53 −66 −87 −102 −122 −144 −172 −226 −300 −405
−20 + ∆ 0 −32 2 3 5 6 11 16
65 80 −43 −59 −75 −102 −120 −146 −174 −210 −274 −360 −480
80 100 −51 −71 −91 −124 −146 −178 −214 −258 −335 −445 −585
−23 + ∆ 0 −37 2 4 5 7 13 19
100 120 −54 −79 −104 −144 −172 −210 −254 −310 -400 −525 −690
120 140 −63 −92 −122 −170 −202 −248 −300 −365 −470 −620 −800
140 160 −27 + ∆ 0 −43 −65 −100 −134 −190 −228 −280 −340 −415 −535 −700 −900 3 4 6 7 15 23
160 180 −68 −108 −146 −210 −252 −310 −380 −465 −600 −780 −1 000
180 200 −77 −122 −166 −236 −284 −350 −425 −520 −670 −880 −1 150
200 225 −31 + ∆ 0 −50 −80 −130 −180 −258 −310 −385 −470 −575 −740 −960 −1 250 3 4 6 9 17 26
225 250 −84 −140 −196 −284 −340 −425 −520 −640 −820 −1 050 −1 350
250 280 −56 −94 −158 −218 −315 −385 −475 −580 −710 −920 −1 200 −1 550
−34 + ∆ 0 4 4 7 9 20 29
280 315 −98 −170 −240 −350 −425 −525 −650 −790 −1 000 −1 300 −1 700
315 355 −62 −108 −190 −268 −390 −475 −590 −730 −900 −1 150 −1 500 −1 900
© ISO 2010 – All rights reserved

−37 + ∆ 0 4 5 7 11 21 32
355 400 −114 −208 −294 −435 −530 −660 −820 −1 000 −1 300 −1 650 −2 100
400 450 −68 −126 −232 −330 −490 −595 −740 −920 −1 100 −1 450 −1 850 −2 400
−40 + ∆ 0 5 5 7 13 23 34
450 500 −132 −252 −360 −540 −660 −820 −1 000 −1 250 −1 600 −2 100 −2 600
500 560 −78 −150 −280 −400 −600
−44
560 630 −155 −310 −450 −660
© ISO 2010 – All rights reserved

Table 3 (continued)

Nominal size Fundamental deviation values

mm Values for ∆
Upper limit deviation, ES
Up to
Up to and
Up to and Above Standard tolerance
including Standard tolerance grades above IT7
Above and including IT8 grades
IT7
including IT8
Na,b P to ZCa P R S T U V X Y Z ZA ZB ZC IT3 IT4 IT5 IT6 IT7 IT8

630 710 −88 −175 −340 −500 −740

−50

Values as for standard tolerance grades above

710 800 −185 −380 −560 −840
800 900 −100 −210 −430 −620 −940
−56
900 1 000 −220 −470 −680 −1 050
1 000 1 120 −250 −520 −780 −1 150
−66 IT7 increased by ∆ −120
−260 −580 −840 −1 300
1 120 1 250
1 250 1 400 −300 −640 −960 −1 450
−78 −140
1 400 1 600 −330 −720 −1 050 −1 600
1 600 1 800 −370 −820 −1 200 −1 850
−92 −170
1 800 2 000 −400 −920 −1 350 −2 000
2 000 2 240 −440 −1 000 −1 500 −2 300
−110 −195
2 240 2 500 −460 −1 100 −1 650 −2 500
2 500 2 800 −550 −1 250 −1 900 −2 900
−135 −240
2 800 3 150 −580 −1 400 −2 100 −3 200
a For determining the values N and P to ZC, see 4.3.2.5
b Fundamental deviations N for standard tolerance grades above IT8 shall not be used for nominal sizes u 1 mm.

ISO 286-1:2010(E)
23
ISO 286-1:2010(E)

Table 4 — Values of the fundamental deviations for shafts a to j

Fundamental deviation values in micrometres
Nominal size Fundamental deviation values
mm Upper limit deviation, es Lower deviation, ei

Up to IT5
and All standard tolerance grades and IT7 IT8
Above IT6
includ-
ing aa ba c cd d e ef f fg g h js j

— 3 −270 −140 −60 −34 −20 −14 −10 −6 −4 −2 0 −2 −4 −6

3 6 −270 −140 −70 −46 −30 −20 −14 −10 −6 −4 0 −2 −4
6 10 −280 −150 −80 −56 −40 −25 −18 −13 −8 −5 0 −2 −5
10 14
−290 −150 −95 −70 −50 −32 −23 −16 −10 −6 0 −3 −6
14 18
18 24
−300 −160 −110 −85 −65 −40 −25 −20 −12 −7 0 −4 −8
24 30
30 40 −310 −170 −120
−100 −80 −50 −35 −25 −15 −9 0 −5 −10
40 50 −320 −180 −130
50 65 −340 −190 −140
−100 −60 −30 −10 0 −7 −12
65 80 −360 −200 −150
80 100 −380 −220 −170
−120 −72 −36 −12 0 −9 −15
100 120 −410 −240 −180

Deviations = ± ITn/2, where n is the standard tolerance grade number

120 140 −460 −260 −200
140 160 −520 −280 −210 −145 −85 −43 −14 0 −11 −18
160 180 −580 −310 −230
180 200 −660 −340 −240
200 225 −740 −380 −260 −170 −100 −50 −15 0 −13 −21
225 250 −820 −420 −280
250 280 −920 −480 −300
−190 −110 −56 −17 0 −16 −26
280 315 −1 050 −540 −330
315 355 −1 200 −600 −360
−210 −125 −62 −18 0 −18 −28
355 400 −1 350 −680 −400
400 450 −1 500 −760 −440
−230 −135 −68 −20 0 −20 −32
450 500 −1 650 −840 −480
500 560
−260 −145 −76 −22 0
560 630
630 710
−290 −160 −80 −24 0
710 800
800 900
−320 −170 −86 −26 0
900 1 000
1 000 1 120
−350 −195 −98 −28 0
1 120 1 250
1 250 1 400
−390 −220 −110 −30 0
1 400 1 600
1 600 1 800
−430 −240 −120 −32 0
1 800 2 000
2 000 2 240
−480 −260 −130 −34 0
2 240 2 500
2 500 2 800
−520 −290 −145 −38 0
2 800 3 150
a Fundamental deviations a and b shall not be used for nominal sizes u 1 mm.

24 © ISO 2010 – All rights reserved

 ISO 286-1:2010(E)

Table 5 — Values of the fundamental deviations for shafts k to zc

Fundamental deviation values in micrometres

Nominal size Fundamental deviation values

mm Lower limit deviation, ei

Up to
and
Up to IT4 includ-
and to ing IT3 All standard tolerance grades
Above IT7 and
inclu-
ding above
IT7
k m n p r s t u v x y z za zb zc
— 3 0 0 +2 +4 +6 +10 +14 +18 +20 +26 +32 +40 +60
3 6 +1 0 +4 +8 +12 +15 +19 +23 +28 +35 +42 +50 +80
6 10 +1 0 +6 +10 +15 +19 +23 +28 +34 +42 +52 +67 +97
10 14 +40 +50 +64 +90 +130
+1 0 +7 +12 +18 +23 +28 +33
14 18 +39 +45 +60 +77 +108 +150
18 24 +41 +47 +54 +63 +73 +98 +136 +188
+2 0 +8 +15 +22 +28 +35
24 30 +41 +48 +55 +64 +75 +88 +118 +160 +218
30 40 +48 +60 +68 +80 +94 +112 +148 +200 +274
+2 0 +9 +17 +26 +34 +43
40 50 +54 +70 +81 +97 +114 +136 +180 +242 +325
50 65 +41 +53 +66 +87 +102 +122 +144 +172 +226 +300 +405
+2 0 +11 +20 +32
65 80 +43 +59 +75 +102 +120 +146 +174 +210 +274 +360 +480
80 100 +51 +71 +91 +124 +146 +178 +214 +258 +335 +445 +585
+3 0 +13 +23 +37
100 120 +54 +79 +104 +144 +172 +210 +254 +310 +400 +525 +690
120 140 +63 +92 +122 +170 +202 +248 +300 +365 +470 +620 +800
140 160 +3 0 +15 +27 +43 +65 +100 +134 +190 +228 +280 +340 +415 +535 +700 +900
160 180 +68 +108 +146 +210 +252 +310 +380 +465 +600 +780 +1 000
180 200 +77 +122 +166 +236 +284 +350 +425 +520 +670 +880 +1 150
200 225 +4 0 +17 +31 +50 +80 +130 +180 +258 +310 +385 +470 +575 +740 +960 +1 250
225 250 +84 +140 +196 +284 +340 +425 +520 +640 +820 +1 050 +1 350
250 280 +94 +158 +218 +315 +385 +475 +580 +710 +920 +1 200 +1 550
+4 0 +20 +34 +56
280 315 +98 +170 +240 +350 +425 +525 +650 +790 +1 000 +1 300 +1 700
315 355 +108 +190 +268 +390 +475 +590 +730 +900 +1 150 +1 500 +1 900
+4 0 +21 +37 +62
355 400 +114 +208 +294 +435 +530 +660 +820 +1 000 +1 300 +1 650 +2 100
400 450 +126 +232 +330 +490 +595 +740 +920 +1 100 +1 450 +1 850 +2 400
+5 0 +23 +40 +68
450 500 +132 +252 +360 +540 +660 +820 +1 000 +1 250 +1 600 +2 100 +2 600
500 560 +150 +280 +400 +600
0 0 +26 +44 +78
560 630 +155 +310 +450 +660
630 710 +175 +340 +500 +740
0 0 +30 +50 +88
710 800 +185 +380 +560 +840
800 900 +210 +430 +620 +940
0 0 +34 +56 +100
900 1 000 +220 +470 +680 +1 050
1 000 1 120 +250 +520 +780 +1 150
0 0 +40 +66 +120
1 120 1 250 +260 +580 +840 +1 300
1 250 1 400 +300 +640 +960 +1 450
0 0 +48 +78 +140
1 400 1 600 +330 +720 +1 050 +1 600
1 600 1 800 +370 +820 +1 200 +1 850
0 0 +58 +92 +170
1 800 2 000 +400 +920 +1 350 +2 000
2 000 2 240 +440 +1 000 +1 500 +2 300
0 0 +68 +110 +195
2 240 2 500 +460 +1 100 +1 650 +2 500
2 500 2 800 +550 +1 250 +1 900 +2 900
0 0 +76 +135 +240
2 800 3 150 +580 +1 400 +2 100 +3 200

© ISO 2010 – All rights reserved 25