Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 170 views

    4.9-3 Bar Code - Set Position

    Uploaded by

    فرزاد شریعت زاده
    The document provides instructions for setting up and calibrating a bar code scanner on a tube sealing machine. It describes: 1) Adjusting the position of the photocells to center the light spots on trigger marks and setting the distance A between the photocell unit and packages. 2) Setting the distance B between photocells and adjusting potentiometers to fine tune positioning. 3) Selecting the light source setting on the photocell unit and adjusting sensitivity by turning knobs until an LED lights up or goes out depending on the material being scanned.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    4.9-3 Bar Code - Set Position

    Uploaded by

    فرزاد شریعت زاده
    170 views4 pages
    The document provides instructions for setting up and calibrating a bar code scanner on a tube sealing machine. It describes: 1) Adjusting the position of the photocells to center the light spots on trigger marks and setting the distance A between the photocell unit and packages. 2) Setting the distance B between photocells and adjusting potentiometers to fine tune positioning. 3) Selecting the light source setting on the photocell unit and adjusting sensitivity by turning knobs until an LED lights up or goes out depending on the material being scanned.

    Original Description:

    tba8

    Original Title

    MM_TBA8_100v

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for setting up and calibrating a bar code scanner on a tube sealing machine. It describes: 1) Adjusting the position of the photocells to center the light spots on trigger marks and setting the distance A between the photocell unit and packages. 2) Setting the distance B between photocells and adjusting potentiometers to fine tune positioning. 3) Selecting the light source setting on the photocell unit and adjusting sensitivity by turning knobs until an LED lights up or goes out depending on the material being scanned.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    170 views4 pages

    4.9-3 Bar Code - Set Position

    Uploaded by

    فرزاد شریعت زاده
    The document provides instructions for setting up and calibrating a bar code scanner on a tube sealing machine. It describes: 1) Adjusting the position of the photocells to center the light spots on trigger marks and setting the distance A between the photocell unit and packages. 2) Setting the distance B between photocells and adjusting potentiometers to fine tune positioning. 3) Selecting the light source setting on the photocell unit and adjusting sensitivity by turning knobs until an LED lights up or goes out depending on the material being scanned.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    4 Jaw system 4.

    9 Bar code

    4.9-3 Bar code - set position


    Machine status Tube sealing finished
    SPC reference 541188-020V
    a) Place the photocells in working position and eliminate any play by
    means of the screw (1). Make sure that the photocells are level.
    b) Crank the machine to 0 and set distance A by shifting the photocell unit.

    1 Screw
    2.2B2951D09.en

    Package Distance A
    355B 569 1 mm
    375S 628 1 mm
    400B 546 1 mm
    500B 698 1mm
    500S 525 1 mm
    750B 536 1 mm
    750S 612 1 mm
    1000B 611 1mm
    1000S 641 1 mm
    1000Sq 658 1 mm
    1000 HiFin 612 1 mm
    1055B 612 1 mm

    (Cont'd)

    Tetra Pak Doc No. MM-82295-0101 275


    4.9 Bar code 4 Jaw system

    (Cont'd)
    c) Set the photocells so that the light spots are centred on the photocell
    trigger marks on the tube by means of the screws (2). Tighten the screws.
    d) Loosen the screws (3) on both photocells and set distance B by moving
    the photocells. Tighten the screws.

    B B = 9 1 mm

    2
    2 Screw
    3 3 Screw

    2.2B2951D09.en
    e) Set the potentiometer (4) to 0.
    f) Step up the machine to Production and perform a Short stop.
    g) Check that the bottom creases are correctly positioned on the packages.
    If they are not, adjust by shifting the photocell unit. Make sure that the
    photocells are level.
    h) Fine set during Production by means of the potentiometer (4).

    4 Potentiometer

    276 Doc No. MM-82295-0101 Tetra Pak


    4 Jaw system 4.9 Bar code

    4.9-4 Bar code - set sensitivity


    Machine status Tube sealing finished
    SPC reference 541188-020V
    a) Remove the plastic cover over the selector.
    b) One photocell unit is equipped with two light sources. For a new
    photocell use the left side of the selector (2). When the first light source
    has been used up, use the right side of the selector (2).
    c) Crank the machine until white packaging material is in front of the
    photocell.
    d) Set the selector (2) in position ”O”. The photocell beams light up white
    packaging material.
    e) Put a piece of black tape on the packaging material in front of the
    photocell.
    f) Set the selector (2) in position ” ”. The photocell beams light up the
    black tape.
    g) Turn the setting knob (3) anti-clockwise until the LED (1) lights up.
    h) Turn the setting knob (3) clockwise just until the LED (1) goes out.
    i) If a white and unbleached printed design background is used at the bar
    code, make the photocells go out as described above, but thereafter turn
    the setting knobs one full turn anti-clockwise.
    2.2B2951D09.en

    j) Set the selector (2) in working position ” ”.


    k) Put back the plastic cover over the selector.

    3 1 LED
    2 Selector
    3 Setting knob

    Tetra Pak Doc No. MM-82295-0101 277


    This document was created with the Win2PDF “print to PDF” printer available at
    http://www.win2pdf.com
    This version of Win2PDF 10 is for evaluation and non-commercial use only.
    This page will not be added after purchasing Win2PDF.
    http://www.win2pdf.com/purchase/

    You might also like