1 CWT5011 Commands 2

CONTENTS
Setup control server phone .........................................................................................................................6
CS Setup Control server phone ..................................................................................................................6
Basic parameters .........................................................................................................................................7
UB Setup RTU com port0 BPS..................................................................................................................7
UP Setup RTU com port0 Parity ................................................................................................................7
SIGNALA Enable or Disable low signal Alarm ..........................................................................................7
RSILOW Setup the thread hold value of Signal Low Alarm.........................................................................7

CWT5011 COMMANDS
DAS Enable or Disable Daily Report SMS at 10.pm everyday.....................................................................8

V3.2 PRTCS Send proof time request SMS to first valid CS number when power up.............................................8
PRTSP Send proof time request SMS to SP when power up .........................................................................8
SP Setup the SP phone number ..................................................................................................................8
RPLSUC Reply SMS for successfully executed SMS command ..................................................................8
RPLERR Reply SMS for incorrect executed SMS command .......................................................................9
PW Setup RTU login Password .................................................................................................................9
ID Setup RTU Device ID ..........................................................................................................................9
PIN Setup RTU PIN code..........................................................................................................................9
PUK Setup RTU PUK code.......................................................................................................................9
SMSC Setup the SMS message center service number ..............................................................................10
DESC Setup the RTU description information ..........................................................................................10
Alarm parameters ...................................................................................................................................... 11
ARING Enable or Disable Alarm RING call function................................................................................ 11
ASC Enable or Disable Auto Answer Voice call from CS phones ............................................................... 11
AWB Enable or Disable description in Alarm SMS ................................................................................... 11
UARTEVENT Enable or Disable Export events from UART ..................................................................... 11
IOAT Setup alert sms resend times...........................................................................................................12
DRPTID Enable or Disable ID information in daily report SMS ................................................................12
DRPDEF Enable or Disable ARM/DISARM information in daily report SMS ............................................12
DRPBAT Enable or Disable Power Supply information in daily report SMS...............................................12
DRPMEM Enable or Disable description information in daily report SMS .................................................13
DRPRSI Enable or Disable GSM Signal information in daily report SMS ..................................................13
DRPDIN Enable or Disable Alarm Wired Inputs information in daily report SMS .......................................13
DRPTMP Enable or Disable build in temperature information in daily report SMS .....................................13
Input and output parameters ....................................................................................................................14
IOTP Setup all inputs and outputs type.....................................................................................................14
IOIP Disable inputs alarm .......................................................................................................................14
IOIC Enable inputs alarm........................................................................................................................14
DINURG Enable or Disable inputs “24 hours” option .................................................................................15
DINSND Enable or Disable inputs “sound alarm” option ............................................................................15
IOAS Setup alarm sms limit interval........................................................................................................15
IOLS Setup sms resend interval when input is in alarm state......................................................................15
DINDLY Setup timer for ensuring inputs alarm ........................................................................................16
S Setup digital inputs alarm sms content ..................................................................................................16
S Setup digital inputs recover sms content................................................................................................16
I Setup inputs name ................................................................................................................................16
O Setup outputs name .............................................................................................................................17
IOIS Read inputs status...........................................................................................................................17
IOOS Read outputs status .......................................................................................................................17
IOOR Setup remember outputs status.........................................................................................................17
IOHT Setup Persist timespan of siren.........................................................................................................17
Control outputs commands........................................................................................................................18
IOOH Control outputs on........................................................................................................................18
IOOL Control outputs off........................................................................................................................18

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

3 CWT5011 Commands 4

IOOP Control outputs pulse.....................................................................................................................18 sspan Setup second timers .......................................................................................................................32

IOPO Setup pulse interval.......................................................................................................................18 mdate Setup week timers ........................................................................................................................32
IOOP Control outputs pulse with time ......................................................................................................18
IOOF Control all outputs by a command ..................................................................................................19 Setup User command ................................................................................................................................34
U Setup the User defined commands........................................................................................................34
AIN parameters..........................................................................................................................................20 Y Setup the User defined commands mapped RTU commands...................................................................34
AIN*H Setup high point of the AIN normal range1...................................................................................20
AIN*L Setup low point of the AIN normal range1 ....................................................................................20 System operation commands ....................................................................................................................35
AIN*SC Setup the scale factor of AIN .....................................................................................................20 PW Setup system password .....................................................................................................................35
AIN*ZE Setup the Offset value of AIN ....................................................................................................20 DAYRP Query the RTU status (Daily report SMS) ...................................................................................35
AIN*OS Setup AIN normal range1’s lag value .........................................................................................21 ARM/BF Arm the RTU system ...............................................................................................................35
AIN*ST Setup AIN upload step value......................................................................................................21 DISARM/CF Disarm the RTU system......................................................................................................35
AIN*R Query AIN Normal range 1 .........................................................................................................21 RST Reset the RTU power ......................................................................................................................35
AIN*C Query Value of AIN ....................................................................................................................21 LOADF Load factory settings .................................................................................................................35
ADS Query all AIN ................................................................................................................................21
AINON Enable AIN ...............................................................................................................................22
AINOFF Disable AIN .............................................................................................................................22
AINURG Setup AIN Urgency .................................................................................................................22
AINSND Setup AIN Sound Alarm...........................................................................................................22
AINTP Setup AIN type ...........................................................................................................................23
AINDRP Setup AIN value send with daily report sms ...............................................................................23
AINAS Setup the minimum time of twice AD alarm sms ..........................................................................23
AINLS Setup interval of resend AD alarm state sms .................................................................................23
AINDLY Setup timespan of ensure AD alarm...........................................................................................24
A Setup the AIN channel’s name..............................................................................................................24
Buzzer parameters.....................................................................................................................................25
BUZEN Enable or disable buzzer sound alarm .........................................................................................25
BUZT Setup buzzer persist time when alarm ............................................................................................25
BUZCLR Reset the interior buzzer sound.................................................................................................25
Interior temperature parameters...............................................................................................................26
TMPH Setup high point of interior temperature normal range ....................................................................26
TMPL Setup low point of interior temperature normal range .....................................................................26
TMPB Setup temperature adjustments value.............................................................................................26
TMPAS Setup the timespan of twice alarm sms ........................................................................................26
TMPLS Setup timespan of resend alarm sms ............................................................................................27
TMPNDLY Setup timespan of ensure alarm status ....................................................................................27
TMPOS Setup lags of temperature alarm range.........................................................................................27
TMPON Enable temperature sensor alarm................................................................................................27
TMPOFF Disable temperature sensor alarm .............................................................................................27
TMPURG Setup temperature sensor alarm is urgency 24 hours..................................................................28
TMPSND Setup temperature sensor sound alarm......................................................................................28
TMPIH Setup interlock output pin of high point .......................................................................................28
TMPIL Setup interlock output pin of low point .........................................................................................28
TMPR Query temperature normal range...................................................................................................28
TMPC Query current temperature value...................................................................................................29
Interior battery parameters .......................................................................................................................30
BATEN Enable or disable power lost alarm..............................................................................................30
POWDLY Setup time of ensure power alarm............................................................................................30
POW Query power status........................................................................................................................30
Interlock parameters .................................................................................................................................31
IOOC Setup outputs action......................................................................................................................31
IOOA Setup link with .............................................................................................................................31
Setup timers...............................................................................................................................................32
mtimer Setup system timers ....................................................................................................................32
mspan Setup minutes timers ....................................................................................................................32

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

5 CWT5011 Commands 6

The instructions of SMS COMMANDS

Setup control server phone
You can use this sms commands to remote control and configure RTU

SMS commands is valid when RTU is in working mode

CS Setup Control server phone
You can execute this sms commands through RS232. But the point is that when the input command is Write
Command Parameters: Example:
made through RS232, the “%” has to be input ahead, while if it is sent via sms, no “%” or “< CR >” is
<n>: CS phone index, form 0~9 CS0=138000000000
needed.
CS<n>=[phone] [phone]: a valid phone number or null
string to delete
Type Format Note
Read
Config commands %command<value><enter> Return OK or ERROR Command Query all CS phone number
Inquire commands %command<?><enter> Return the result or ERROR
CS?
Delete
Command

CS<n>

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

7 CWT5011 Commands 8

DAS Enable or Disable Daily Report SMS at 10.pm everyday

Write Parameters Example:
Basic parameters Command <En> DAS=1
0: Disable
DAS=<En> 1: Enable (default)
UB Setup RTU com port0 BPS Read
Write Parameters Example: Command
Command <BPS>: 300-115200 UB=9600
DAS =?
Default BPS is 9600BPS
UB=<BPS>
Read PRTCS Send proof time request SMS to first valid CS number when power up
Command Write Parameters Example:
Command <En>: PRTCS=1
UB=? 0: Disable
PRTCS=<En> 1: Enable (default)
Read
UP Setup RTU com port0 Parity Command
Write Parameters Example:
Command <Parity>: UP=0 PRTCS=?
0: None (default)
UP=<Parity> 1: Odd Parity PRTSP Send proof time request SMS to SP when power up
2: Even Parity Write Parameters Example:
3: 0 Parity Command <En>: PRTSP=1
4: 1 Parity 0: Disable (default)
Read PRTSP=<En> 1: Enable
Command Read
Command
UP=?
PRTSP=?
SIGNALA Enable or Disable low signal Alarm
SP Setup the SP phone number
Write Parameters Example:
Command <En> SIGNALA=1 Write SP phone number is a phone that can automatic reply a SMS to any
0: Disable (default) Command incoming SMS, RTU use it to update interior Clocker by the timestamp in
SIGNALA=<En> 1: Enable SMS, the SMS contents is not important
Read SP=<phone>
Command Read SP phone number can be RTU’s simcard number. So it will send proof
Command time sms to itself when power up and RTU will receive this sms. So RTU
SIGNALA=? can take out the time stamp from the sms PDU.
SP=? Note: if the RTU’s simcard is changed, you must change the SP also.
RSILOW Setup the thread hold value of Signal Low Alarm
RPLSUC Reply SMS for successfully executed SMS command
Write Parameters Example:
Command <Signal> RSILOW=11 Write Parameters Example:
Command <En>: RPLSUC=1
Normal Signal range is 10-30
0: Disable
RSILOW=<Signal> 0 or 99 means no signal at all
RPLSUC=<En> 1: Enable (default)
Read
Read
Command When signal low, RTU will make a sound Command
alarm and try to send SMS
RSILOW =? RPLSUC=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

9 CWT5011 Commands 10

RPLERR Reply SMS for incorrect executed SMS command

Write Parameters Example: SMSC Setup the SMS message center service number
Command <En>: RPLERR=1 Write
0: Disable
Command
RPLERR=<En> 1: Enable (default)
Read
Command SMSC=<code>
Read Default is NULL (can works well in most of
RPLERR=? Command area and country)

PW Setup RTU login Password SMSC=?

Write Password is 6 characters string Example:
Command PW=888888
DESC Setup the RTU description information
PW=<psd> Write Example:
Read Default password is 000000 Command DESC=room1
Command
DESC=<string>
PW=? Read Description is basic information about the
Command device, etc, the address, the administrator and
ID Setup RTU Device ID so on.
Write Device ID is a 8 characters string Example: DESC=?
Command Default ID is null ID=00000001

ID=<id>
Read ID is used in GPRS CWT_IO protocol
Command

ID=?

PIN Setup RTU PIN code

Write PIN code is 4 number Example:
Command PIN=1234

PIN=<code>
Read
Command

PIN=?

PUK Setup RTU PUK code

Write PUK code including 8 numbers Example:
Command PUK=12345678

PUK=<code>
Read
Command

PUK=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

11 CWT5011 Commands 12

IOAT Setup alert sms resend times

Alarm parameters
Write Parameters Example:
Command <n>: IOAT=3
ARING Enable or Disable Alarm RING call function sms resend times
Write Parameters Example: IOAT=<n> default is 1
Command <En>: ARING=1 Read
0: Disable (default) Command
ARING=<En> 1: Enable
Read If enable RING call, any alert will cause a
IOAT=?
Command voice call to CS phone numbers.

DRPTID Enable or Disable ID information in daily report SMS

ARING=?
Write Parameters Example:
Command <En>: DRPTID=1
ASC Enable or Disable Auto Answer Voice call from CS phones
0: Disable
Write Parameters Example:
Command <En>: ASC=1 DRPTID=<En> 1: Enable (default)
0: Disable Read
ASC=<En> 1: Enable (default) Command
Read
Command DRPTID=?

ASC=? DRPDEF Enable or Disable ARM/DISARM information in daily report SMS

Write Parameters Example:
AWB Enable or Disable description in Alarm SMS
Command <En>: DRPDEF=1
Write Parameters Example:
0: Disable
Command <En>: AWB=1
DRPDEF=<En> 1: Enable (default)
0: Disable
Read
AWB=<En> 1: Enable (default)
Add the description and timestamp with alert Command
Read
Command sms
DRPDEF=?
AWB=?
DRPBAT Enable or Disable Power Supply information in daily report SMS
UARTEVENT Enable or Disable Export events from UART Write Parameters Example:
Write Parameters Example: Command <En>: DRPBAT=1
Command <En>: UARTEVENT=1 0: Disable
0: Disable (default) DRPBAT=<En> 1: Enable (default)
UARTEVENT=<En> 1: Enable Read
Read Command
Command
DRPBAT=?
UARTEVENT=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

13 CWT5011 Commands 14

DRPMEM Enable or Disable description information in daily report SMS

Write Parameters Example:
Input and output parameters
Command <En>: DRPMEM=1
0: Disable
DRPMEM=<En> 1: Enable (default) IOTP Setup all inputs and outputs type
Read Setup all I/O channels type Parameters Example:
Command Write <I0I1I2I3I4I5I6I7> IOTP=33333333111100
Command Inputs type: 00
DRPMEM=? 0: DISABLE
IOTP=<I0I1I2I3I4I5I6I7><O0O1 1: TO OPEN ALARM (EDGE)
O2O3O4O5O6O7> 2: TO OPEN ALARM(LEVEL)
DRPRSI Enable or Disable GSM Signal information in daily report SMS
Setup single input type 3: TO CLOSE ALARM (EDGE)(default) Example:
Write Parameters Example:
Write 4: TO CLOSE ALARM(LEVEL) IOTPI=0,2
Command <En>: DRPRSI=1
Command <O0O1O2O3O4O5O6O7>
0: Disable Outputs type: Setup input0 type is 2
DRPRSI=<En> 1: Enable (default) IOTPI=<n>,<In> 0: DISABLE
Read Setup single output type 1: GENERAL OUTPUT (default) Example:
Command Write 2: BUZZER IOTPO=0,1
Command 3: SNAPSHOOT
DRPRSI=? 4: SIREN Setup output0 type is 1
IOTPO=<n>,<On> <n>: 0~7 (DI or DO index)
DRPDIN Enable or Disable Alarm Wired Inputs information in daily report SMS Read
Command
Write Parameters Example:
Command <En>: DRPDIN=1
IOTP=?
0: Disable
DRPDIN=<En> 1: Enable (default)
IOIP Disable inputs alarm
Read Write Parameters Example:
Command Command <n/nn/…/nnnnnnnn>: Disable input0 alarm
1 digit to 8 digits IOIP=0
DRPDIN=? IOIP=<n/nn/…/nnnnnnnn> n: 0~7 (input index)
Read
Disable input2/3/5
Command
DRPTMP Enable or Disable build in temperature information in daily report SMS alarm
Write Parameters Example: IOIP=235
IOIP=?
Command <En>: DRPTMP=1
0: Disable IOIC Enable inputs alarm
DRPTMP=<En> 1: Enable (default) Write Parameters Example:
Read Command <n/nn/…/nnnnnnnn>: IOIC=1
Command 1 digit to 8 digits IOIC=01234567
IOIC=<n/nn/…/nnnnnnnn> n: 0~7 (input index)
DRPTMP=? Read
Command

IOIC=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

15 CWT5011 Commands 16

DINURG Enable or Disable inputs “24 hours” option DINDLY Setup timer for ensuring inputs alarm
Write Parameters Example: Write Parameters Example:
Command <n>: DINURG0,1 Command <n>: DINDLY0,5
0~7 (input index) 0～7 (Inputs index)
<En>: Enable input0 “24 DINDLY<n>,<time> <time>:
DINURG<n>,<En> 0: Disable (default) hours” option 0~65535 (sec)
1: Enable
Read Default is 0
Read
Command
Command

DINDLY<n>?
DINURG=?

S Setup digital inputs alarm sms content

DINSND Enable or Disable inputs “sound alarm” option
Write Parameters Example:
Write Parameters Example:
Command <nn>: S00=sensor alarm
Command <n>: DINSND=1,0
00～07 (inputs alarm sms index)
0~7 (input index)
S<nn>=<string> <string>:
<En>: Disable input1 “sound
Alarm sms
DINSND<n>,<En> 0: Disable alarm” option
Read
1: Enable (default)
Command
Read
Command
S<nn>=?

DINSND=?
S Setup digital inputs recover sms content
Write Parameters Example:
IOAS Setup alarm sms limit interval
Command <nn>: S08=alarm recover
Write Parameters Example:
08～15 (inputs recover sms index)
Command <n>: IOAS0,2
S<nn>=<string> <string>:
0～7 (Inputs index)
Recover sms
IOAS<n>,<time> <time>:
Read
0~255 (min)
Command
Read Default is 0
Command
S<nn>=?

IOAS<n>?
I Setup inputs name
Write Parameters Example:
IOLS Setup sms resend interval when input is in alarm state
Command <nn>: I02=sensor
Write Parameters Example:
00～07 (inputs name index)
Command <n>: IOLS0,2
I<nn>=<string> <string>:
0～7 (Inputs index)
Name
IOLS<n>,<time> <time>:
Read
0~255 (min)
Command
Read Default is 0
Command
I<nn>=?
IOLS<n>?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

17 CWT5011 Commands 18

O Setup outputs name

Write Parameters Example:
Control outputs commands
Command <nn>: O02=pump
00～07 (outputs name index)
O<nn>=<string> <string>:
IOOH Control outputs on
Name
control Parameters Example:
Read
Command <nnnnnnnn>: Control ouput0 on:
Command 1 digit to 8 digits IOOH0
IOOH<nnnnnnnn> n: 0~7 (outputs index)
O<nn>=? Control ouput2/3/5 on:
IOOH235

IOIS Read inputs status IOOL Control outputs off

Read control Parameters Example:
Command Command <nnnnnnnn>: IOOL0
1 digit to 8 digits IOOL01234567
IOIS IOOL<nnnnnnnn> n: 0~7 (outputs index)

IOOS Read outputs status IOOP Control outputs pulse

Read control Parameters Example:
Command Command <nnnnnnnn>: IOOP0
1 digit to 8 digits IOOP01234567
IOOS IOOP<nnnnnnnn> n: 0~7 (outputs index)
default pulse interval is 1 second, and the
IOOR Setup remember outputs status interval can be set by command IOPO
Write Parameters Example:
Command <En>: IOOR=1 IOPO Setup pulse interval
0: Disable (default) Write Parameters Example:
IOOR=<En> 1: Enable Command <sec>: IOPO5
0~65535 (second)
Read
IOPO<sec>
Command
Read
Command
IOOR=?
IOPO?
IOHT Setup Persist timespan of siren
Write Parameters Example: IOOP Control outputs pulse with time
Command <n>: IOHT=10 control Parameters Example:
0～255 (min) Command <nnnnnnnn>: Generate a 10 seconds
IOHT=<n> 1 digit to 8 digits pulse on output0:
Read Default is 15 minutes IOOP<nnnnnnnn>,<sec> IOOP0,10
Command n: 0~7 (output index)
Generate a 3 seconds
IOHT=? <sec>: 0~65535 (second) pulse on output 2/3/5:
IOOP235,3

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

19 CWT5011 Commands 20

IOOF Control all outputs by a command

AIN parameters
control Parameters Example:
Command <S0S1S2S3S4S5S6S7>: 8 digits Control output4/5 off
Sn: and others on
AIN*H Setup high point of the AIN normal range1
IOOF<S0S1S2S3S4S5S6S7> 0: output off IOOF11110011
Write Parameters Example:
1: output on
Command <n>: AIN0H=30.01
0~3 (AIN index)
AIN<n>H=<Val> <Val>: a float value
Read
Command

AIN<n>H=?

AIN*L Setup low point of the AIN normal range1

Write Parameters Example:
Command <n>: AIN0L=10.53
0~3 (AIN index)
AIN<n>L=<Val> <Val>: a float value
Read
Command

AIN<n>L=?

AIN*SC Setup the scale factor of AIN

Write Parameters Example:
Command <n>: AIN0SC=62.00
0~3 (AIN index)
AIN<n>SC=<Val> <Val>: a float value
Read Reference
Command AIN value = AIN*[Scale Factor]-Offset

AIN<n>SC=?

AIN*ZE Setup the Offset value of AIN

Write Parameters Example:
Command <n>: AIN0ZE=12.00
0~3 (AIN index)
AIN<n>ZE=<Val> <Val>: a float value
Read Reference
Command AIN value = AIN*[Scale Factor]-Offset

AIN<n>ZE=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

21 CWT5011 Commands 22

AIN*OS Setup AIN normal range1’s lag value AINON Enable AIN
Write Parameters Example: Write Parameters Example:
Command <n>: AIN0OS=2.00 Command <n>: Enable AIN0
0~3 (AIN index) 0~3 (AIN index) AINON=0
AIN<n>OS=<lag> <lag>: a float value AINON=<n>
Default is 0 Read
Read Command
Command
AINON=?
AIN<n>OS=?
When AIN value goes out of normal rang1, RTU will alarm. AINOFF Disable AIN
Reference But will not return to normal state before AIN return into range Write Parameters Example:
AINH-lag and AINL+lag Command <n>: Disable AIN1
0~3 (AIN index) AINOFF=1
AIN*ST Setup AIN upload step value AINOFF=<n>
Read
Write Parameters Example:
AIN0ST=5.00 Command
Command <n>:
0~3 (AIN index)
AINOFF=?
AIN<n>ST=<val> <lag>: a float value
Default is 0
AINURG Setup AIN Urgency
Read
Write Parameters Example:
Command Command <n>: Enable AIN0 as urgent
0~3 (AIN index) alarm
AIN<n>ST=? AINURG=<n>,<En> <En>:
0: Disable (default) AINURG=0,1
AIN*R Query AIN Normal range 1 1: Enable
Execution Parameters Read
Command <n>: Command
0~3 (AIN index)
AINURG=?
AIN<n>R

AINSND Setup AIN Sound Alarm

AIN*C Query Value of AIN
Write Parameters Example:
Execution Parameters
Command <n>: Enable AIN0 sound
Command <n>:
0~3 (AIN index) alarm
0~3 (AIN index)
AINSND=<n>,<En> <En>: AINSND=0,1
AIN<n>C 0: Disable
1: Enable (default)
ADS Query all AIN Read
Execution Command
Command
AINSND=?
ADS

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

23 CWT5011 Commands 24

AINTP Setup AIN type AINDLY Setup timespan of ensure AD alarm

Write Parameters Example: Write Parameters Example:
Command <n>: AINTP=0,1 Command <sec>: AINDLY=2
0~3 (AIN index) 0~255 (second), default is 0
AINTP=<n>,<type> <type>:
AINDLY=<sec> 0 means disable the function
0: Voltage
Read
1: Current (default)
Command
Read
Command
AINDLY=?
AINTP=?
A Setup the AIN channel’s name
AINDRP Setup AIN value send with daily report sms Write Parameters Example:
Write Parameters Example: Command <nn>: A00=temperature
Command <S0S1S2S3>: Enable AIN 0/1 daily 00~03 (AIN index)
A<nn>=<string> <string>:
4 AIN channels report
AINDRP=<S0S1S2S3> Sn: AINDRP=1100 Max 24 characters.
0: Disable (default) Read
1: Enable Command
Read
Command A<nn>=?

AINDRP=?

AINAS Setup the minimum time of twice AD alarm sms

Write Parameters Example:
Command <min>: AINAS=2
0~255 (min), default is 0
AINAS=<min> 0 means disable the function
Read
Command

AINAS=?

AINLS Setup interval of resend AD alarm state sms

Write Parameters Example:
Command <min>: AINLS=2
0~255 (min), default is 0
AINLS=<min> 0 means disable the function
Read
Command

AINLS=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

25 CWT5011 Commands 26

Buzzer parameters Interior temperature parameters

BUZEN Enable or disable buzzer sound alarm TMPH Setup high point of interior temperature normal range
Write Parameters Example: Write Parameters Example:
Command <En>: BUZEN=1 Command <Val>: -127~128 TMPH=30
0: Disable
TMPH=<Val>
BUZEN=<En> 1: Enable (default)
Read
Read The sound alarm include interior buzzer and
Command
Command any output used as Siren or Buzzer

TMPH=?
BUZEN=?

TMPL Setup low point of interior temperature normal range

BUZT Setup buzzer persist time when alarm
Write Parameters Example:
Write Parameters Example: Command <Val>: -127~128 TMPL=10
Command <sec>: 0~255 seconds BUZT=15
TMPL=<Val>
BUZT=<sec> Default Time span is 60 seconds Read
Read Command
Command
TMPL=?
BUZT=?
TMPB Setup temperature adjustments value
BUZCLR Reset the interior buzzer sound Write Parameters Example:
Command <Val>: -127~128 TMPB=2
Execution
Command
TMPB=<Val>
Read
BUZCLR
Command

TMPB=?

TMPAS Setup the timespan of twice alarm sms

Write Parameters Example:
Command <min>: TMPAS=2
0~255 (min), default is 0
TMPAS=<min> 0 means disable the function
Read
Command

TMPAS=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

27 CWT5011 Commands 28

TMPLS Setup timespan of resend alarm sms TMPURG Setup temperature sensor alarm is urgency 24 hours
Write Parameters Example: Write Parameters Example:
Command <min>: TMPLS=2 Command <En>: TMPURG=1
0~255 (min), default is 0 0: Disable
TMPURG=<En> 1: Enable
TMPLS=<min> 0 means disable the function
Read
Read
Command
Command

TMPURG=?
TMPLS=?

TMPSND Setup temperature sensor sound alarm

TMPNDLY Setup timespan of ensure alarm status
Write Parameters Example:
Write Parameters Example: Command <En>: TMPSND=1
Command <sec>: TMPNDLY=2 0: Disable
0~255 (second), default is 0 TMPSND=<En> 1: Enable
TMPNDLY=<sec> 0 means disable the function Read
Read Command
Command
TMPSND=?
TMPNDLY=?
TMPIH Setup interlock output pin of high point
TMPOS Setup lags of temperature alarm range Write Parameters Example:
Command <DO>: TMPIH=0
Write Parameters Example:
0~n (output index)
Command <val>: TMPOS=2
TMPIH=<DO> 255 is none
0~255
Read
TMPOS=<val>
Command
Read
Command TMPIH=?

TMPOS=? TMPIL Setup interlock output pin of low point

Write Parameters Example:
TMPON Enable temperature sensor alarm Command <DO>: TMPIL=1
Execution 0~n (output index)
Command TMPIL=<DO> 255 is none
Read
TMPON Command

TMPIL=?
TMPOFF Disable temperature sensor alarm
Execution
TMPR Query temperature normal range
Command
Execution
Command
TMPOFF

TMPR

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

29 CWT5011 Commands 30

TMPC Query current temperature value

Interior battery parameters
Execution
Command
BATEN Enable or disable power lost alarm
TMPC Write Parameters Example:
Command <En>: BATEN=1
0: Disable
BATEN=<En> 1: Enable
Read
Command

BATEN=?

POWDLY Setup time of ensure power alarm

Write Parameters Example:
Command <sec>: 0～65535 seconds POWDLY=15
Default is 5, 0 means disable the function
POWDLY=<sec>
Read
Command

POWDLY=?

POW Query power status

Execution
Command

POW

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

31 CWT5011 Commands 32

Interlock parameters Setup timers

IOOC Setup outputs action mtimer Setup system timers

Write Parameters Write Parameters Example:
Command <nnnnnnnn>: 0~7 Outputs’ action when alert by “link with” Command <n>: 0~5 (mtimer index) Setup send daily report
<xxxxxxxx>: 0~7 Outputs’ action when recover by “link with” <HH>: 0~24 (hour) sms at 17:50 everyday
IOOC=<nnnnnnnn><xxxxxxxx> n & x: mtimer<n>=<HH>,<MM>,<action> <MM>: 0~60 (minute)
0: OPEN <action>: 0~39 mtimer0=17,50,16
1: CLOSE Read
2: CLOSE PULSE Command
3: CLOSE 300S
4: CLOSE 30S mtimer=?
5: CLOSE 60S
6: NONE mspan Setup minutes timers
Read Write Parameters Example:
Command Command <n>: 0~5 (mspan index) Setup send daily report
<min>: 0~65535 (minute) sms every 30 minutes
IOOC=? mspan<n>=<min>,<action> <action>: 0~39 mspan0=30,16
Read
IOOA Setup link with Command
Write Parameters
Command <n>: 0~7 output index mspan=?
<index>: “link with” index
sspan Setup second timers
IOOA=<n><index> 0: NONE 8: 7 input alert 16: humidity sensor
Write Parameters Example:
1: 0 input alert 9: 0 AD alert 17: 0 Ex-temp alert Command <n>: 0~5 (mspan index) Setup send daily report
2: 1 input alert 10: 1 AD alert 18: 1 Ex-temp alert <min>: 0~65535 (second) sms every 30 seconds
3: 2 input alert 11: 2 AD alert 19: 2 Ex-temp alert sspan<n>=<min>,<action> <action>: 0~39 sspan0=30,16
4: 3 input alert 12: 3 AD alert 20: 3 Ex-temp alert Read
5: 4 input alert 13: Interior temp alert 21: 4 Ex-temp alert Command
6: 5 input alert 14: system power down 22: 5 Ex-temp alert
sspan=?
7: 6 input alert 15: Server call

mdate Setup week timers

Read
Write Parameters Example:
Command
Command <n>: 0~6 Setup send daily
<day>: 0~6 (week day) report sms at 18:34
IOOC=? mdate<n>=<day>,<HH>,<MM>,<action> <HH>: 0~24 (hour) Monday
<MM>: 0~60 (minute)
Example: config output0 on when input3 alert and output0 off when input3 recover <action>: 0~39 Mdate0=0,18,34,16
Read
The sms command is: Command
IOOC1666666606666666
IOOA04 mdate=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

33 CWT5011 Commands 34

Action index:

0: None 14: Pulse OC 3 28: Howl alarm Setup User command

1: Disarm 15: Snapshoot 29: Clocker
2: Arm 16: daily report sms 30: Enable buzzer
3: Driver OC 0 (output0 on) 17: Export state by uart0 31: Disable buzzer U Setup the User defined commands
4: Driver OC 1 (output1 on) 18: Upload state by sms 32: Upload din by gprs Write Parameters Example:
5: Driver OC 2 (output2 on) 19: Exec user cmd0 33: Upload dout by gprs Command <nn>: Use “abc” instead of
6: Driver OC 3 (output3 on) 20: Exec user cmd1 34: Upload ain by gprs 00: User defined command 0 command “IOOH0”
7: OC 0 off 21: Exec user cmd2 35: Upload modbus by gprs U<nn>=<string> 01: User defined command 1
…… U00=abc
8: OC 1 off 22: Exec user cmd3 36: Upload graycode by gprs
9: OC 2 off 23: Exec user cmd4 37: Save samples to flash 05: User defined command 5
<string>:
10: OC 3 off 24: Exec user cmd5 38: Upload din counter
user defined command contents
11: Pulse OC 0 25: Exec user cmd6 39: Din counter reset
max 24 characters
12: Pulse OC 1 26: Upload state by gprs
Read
13: Pulse OC 2 27: Buzzer beep
Command

U<nn>=?

Y Setup the User defined commands mapped RTU commands

Write Parameters Example:
Command <nn>: Use “abc” instead of
00: RTU command 0 command “IOOH0”
Y<nn>=<string> 01: RTU command 1
…… Y00=IOOH0
05: RTU command 5
<string>:
RTU command contents
max 24 characters
Read
Command

Y<nn>=?

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954 www.mobq2000.com

35

System operation commands

PW Setup system password

Write Parameters Example:
Command <psd>: 6 digits PW=123456

PW=<pad>
Read
Command

PW=?

DAYRP Query the RTU status (Daily report SMS)

Read
Command

DAYRP

ARM/BF Arm the RTU system

Execution
Command

ARM

DISARM/CF Disarm the RTU system

Execution
Command

DISARM

RST Reset the RTU power

Execution
Command

RST

LOADF Load factory settings

Execution
Command

LOADF

SHEN ZHEN YIKEHUDONG TECHNOLOGY TRADE LTD TEL：+86-755-26719954