Sikagrout®-215 (New) : Product Data Sheet

PRODUCT DATA SHEET
SikaGrout®-215 (new)
HIGH PRECISION, GENERAL PURPOSE, NON-SHRINK CEMENTITIOUS GROUT
DESCRIPTION CHARACTERISTICS / ADVANTAGES

A non-shrink, cementitious premixed grout with ex- ▪ Easy to use, just add water
tended working time to suit local ambient temperat- ▪ Good flow characteristic
ures. ▪ Adjustable consistency
▪ Rapid strength development
USES ▪ Shrinkage compensated
▪ High final strength
For grouting over a wide range of applications: ▪ Non-Corrosive
▪ Anchor bolts ▪ Non-Toxic
▪ Machine bedding/base plates
▪ Supporting bridge bearing pads
▪ Pre-cast concrete section
▪ Dry pack applications
▪ Cavities, gaps and recesses
▪ For grouting method of concrete repair
▪ Marine structure
PRODUCT INFORMATION
Packaging 25 kg bag
Appearance / Colour Powder / Grey
Shelf life 6 months from the date production if stored in undamage and unopened
original sealed bags
Storage conditions Stored in dry condition between +10 °C - +30 °C
Density ~2.26 kg/L
TECHNICAL INFORMATION
Compressive Strength 1 day ~25.0 N/mm2 (ASTM C-109)
3 days ~40.0 N/mm2
7 days ~52.0 N/mm2
28 days ~65.0 N/mm2
Tensile Strength in Flexure 28 days > 6.0 N/mm2 (ASTM C-348)
Product Data Sheet

June 2020, Version 05.01
020201010010000128
1/3
Tensile Adhesion Strength 28 days >1.5 N/mm2
Concrete failure, over roughened
concrete surface
28 days >2.5 N/mm2
Over mechanically roughened old
grout surface
Expansion 1 - 3 h (at +27 °C) 0.30 - 1.40 % (ASTM C-940)
APPLICATION INFORMATION
Mixing Ratio 4.0 L per 25 kg bag (water per powder = 16 % by weight)
Consumption ~1 940 kg/m3 of mortar
Yield ~12.80 L per 25 kg bag
Layer Thickness Recommended thickness is 20 - 100 mm
Flowability Flow cone (mm) 240 - 280 mm (ASTM C230/230M)
Product Temperature < +30 °C

Ambient Air Temperature +10 °C - +35 °C
Substrate Temperature +10 °C - +35 °C
Pot Life 25 min
Setting Time 4-8h
APPLICATION INSTRUCTIONS APPLICATION

SUBSTRATE QUALITY / PRE-TREATMENT Within 25 minutes after mixing, place grout into forms
from one side to avoid air entrapment. Do not vibrate.
SURFACE PREPARATION Use a suitable head box of 150-200 mm and maintain
▪ Remove dirt, oil, grease, loose material and other the grout head at all times to ensure a continuous
bond-inhibiting materials. flow. Gentle tapping or pulling loops of wire from one
▪ Anchor bolts to be grouted must be degreased with
side may assist the flow of the mortar under difficult
suitable solvent.
▪ Concrete must be sound and roughened to promote working conditions.
mechanical adhesion. CURING TREATMENT
▪ Prior to pouring, surface must be wetted to satur-
ated surface dry. Wet cure for a minimum 3 days with wet hessian,
plastic sheet or apply a curing compound (Antisol)
FORMING
For pourable grout, construct forms to retain grout CLEANING OF EQUIPMENT
without leakage. Forms should be lined or coated with
bond-breaker for easy removal. Forms should be suffi- Clean all tolls and application equipment with water
ciently high to accommodate head of grout. Where immediately after use. Hardened and / or cured ma-
grout tight form is difficult to achieve, use SikaSet Ac- terial can only be remove mechanically.
celarator as water plug (refer to PDS SikaSet Accelarat-
or). IMPORTANT CONSIDERATIONS
MIXING ▪ Minimum application thickness : 10 mm
▪ Recommended thickness of SikaGrout®-215 (new) in
Put measured quantity of water (depend on the re- one pour is 20 mm to 100mm.
quired consistency) into a mixing vessel. Add slowly ▪ If the thickness exceeds 100 mm, special procedure
the total contents of SikaGrout®-215 (new) while mix- must be taken to anticipate temperature rise. Iced
ing. Mix continuously for 3 minutes to achieve even water, add coarse aggregate to the mix (max. 40% by
consistency. Use a mechanically low speed drill (400 - powder weight), or both of them may be used to
600 rpm) with mixing paddle or appropriately sized eliminate temperature rise.
mortar mixer. ▪ Variations in cement could cause shade differences
in colour of the mortar.
Product Data Sheet

020201010010000128
2/3
BASIS OF PRODUCT DATA LEGAL NOTES
All technical data stated in this Data Sheet are based The information, and, in particular, the recommenda-
on laboratory tests. Actual measured data may vary tions relating to the application and end-use of Sika
due to circumstances beyond our control. products, are given in good faith based on Sika's cur-
rent knowledge and experience of the products when
LOCAL RESTRICTIONS properly stored, handled and applied under normal
conditions in accordance with Sika's recommenda-
Note that as a result of specific local regulations the tions. In practice, the differences in materials, sub-
declared data and recommended uses for this product strates and actual site conditions are such that no war-
may vary from country to country. Consult the local ranty in respect of merchantability or of fitness for a
Product Data Sheet for the exact product data and particular purpose, nor any liability arising out of any
uses. legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
ECOLOGY, HEALTH AND SAFETY mendations, or from any other advice offered. The
user of the product must test the product’s suitability
For information and advice on the safe handling, stor- for the intended application and purpose. Sika re-
age and disposal of chemical products, users shall serves the right to change the properties of its
refer to the most recent Safety Data Sheet (SDS) con- products. The proprietary rights of third parties must
taining physical, ecological, toxicological and other be observed. All orders are accepted subject to our
safety-related data. current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request.
PT. Sika Indonesia Head Office and

Manufacturing
Jl. Raya Cibinong-Bekasi Km.20
Limusnunggal-Cileungsi
Bogor 16820-Indonesia
Tel. +62 21 8230025, Fax +62 21
8230026
SikaGrout-215new-en-ID-(06-2020)-5-1.pdf
Product Data Sheet

020201010010000128
3/3

Sikagrout®-215 (New) : Product Data Sheet

Uploaded by

Copyright:

Available Formats

Sikagrout®-215 (New) : Product Data Sheet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sikagrout®-215 (New) : Product Data Sheet

Uploaded by

Copyright:

Available Formats

PRODUCT DATA SHEET

DESCRIPTION CHARACTERISTICS / ADVANTAGES

Product Data Sheet

Product Temperature < +30 °C

APPLICATION INSTRUCTIONS APPLICATION

Product Data Sheet

PT. Sika Indonesia Head Office and

Product Data Sheet

You might also like