Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 226 views

    Lab 10.3 - Configure IPv6 Addressing

    Uploaded by

    Recky Jimmy
    This document provides instructions for configuring IPv6 addressing on a router and connected servers and clients. It describes configuring IPv6 addresses on the router interfaces, as well as link-local addresses. It also provides steps to configure IPv6 addresses on servers and clients based on an addressing table. Finally, it includes steps to test connectivity between the clients and servers by opening web pages and pinging the ISP to verify the IPv6 network configuration.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Lab 10.3 - Configure IPv6 Addressing

    Uploaded by

    Recky Jimmy
    226 views3 pages
    This document provides instructions for configuring IPv6 addressing on a router and connected servers and clients. It describes configuring IPv6 addresses on the router interfaces, as well as link-local addresses. It also provides steps to configure IPv6 addresses on servers and clients based on an addressing table. Finally, it includes steps to test connectivity between the clients and servers by opening web pages and pinging the ISP to verify the IPv6 network configuration.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for configuring IPv6 addressing on a router and connected servers and clients. It describes configuring IPv6 addresses on the router interfaces, as well as link-local addresses. It also provides steps to configure IPv6 addresses on servers and clients based on an addressing table. Finally, it includes steps to test connectivity between the clients and servers by opening web pages and pinging the ISP to verify the IPv6 network configuration.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    226 views3 pages

    Lab 10.3 - Configure IPv6 Addressing

    Uploaded by

    Recky Jimmy
    This document provides instructions for configuring IPv6 addressing on a router and connected servers and clients. It describes configuring IPv6 addresses on the router interfaces, as well as link-local addresses. It also provides steps to configure IPv6 addresses on servers and clients based on an addressing table. Finally, it includes steps to test connectivity between the clients and servers by opening web pages and pinging the ISP to verify the IPv6 network configuration.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 3

    Packet Tracer - Configure IPv6 Addressing

    Addressing Table
    Device Interface IPv6 Address/Prefix Default Gateway

    R1 G0/0 2001:db8:1:1::1/64 N/A

    R1 G0/0
    fe80::1 N/A

    R1
    G0/1 2001:db8:1:2::1/64 N/A

    R1 G0/1
    fe80::1 N/A

    R1
    S0/0/0 2001:db8:1:a001::2/64 N/A

    R1 S0/0/0
    fe80::1 N/A

    Sales NIC 2001:db8:1:1::2/64 fe80::1


    Billing NIC 2001:db8:1:1::3/64 fe80::1
    Accounting NIC 2001:db8:1:1::4/64 fe80::1
    Design NIC 2001:db8:1:2::2/64 fe80::1
    Engineering NIC 2001:db8:1:2::3/64 fe80::1
    CAD NIC 2001:db8:1:2::4/64 fe80::1
    ISP S0/0/0 2001:db8:1:a001::1 fe80::1

    Objectives
    Part 1: Configure IPv6 Addressing on the Router
    Part 2: Configure IPv6 Addressing on Servers
    Part 3: Configure IPv6 Addressing on Clients
    Part 4: Test and Verify Network Connectivity

    Background
    In this activity, you will practice configuring IPv6 addresses on a router, servers, and clients. You will also
    practice verifying your IPv6 addressing implementation.

    Part 1: Configure IPv6 Addressing on the Router


    Step 1: Enable the router to forward IPv6 packets.
    a. Click R1 and then the CLI tab. Press Enter.
    Open a configuration window

    b. Enter privileged EXEC mode.


    c. Enter the ipv6 unicast-routing global configuration command. This command must be entered to enable
    the router to forward IPv6 packets.
    R1(config)# ipv6 unicast-routing

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 3 www.netacad.com
    Packet Tracer - Configure IPv6 Addressing

    Step 2: Configure IPv6 addressing on GigabitEthernet0/0.


    a. Enter the commands necessary to move to interface configuration mode for GigabitEthernet0/0.
    b. Configure the IPv6 address with the following command:
    R1(config-if)# ipv6 address 2001:db8:1:1::1/64
    c. Configure the link-local IPv6 address with the following command:
    R1(config-if)# ipv6 address fe80::1 link-local
    d. Activate the interface.
    R1(config-if)# no shutdown

    Step 3: Configure IPv6 addressing on GigabitEthernet0/1.


    a. Enter the commands necessary to move to interface configuration mode for GigabitEthernet0/1.
    b. Refer to the Addressing Table for the correct IPv6 address.
    c. Configure the IPv6 address, the link-local address and activate the interface.

    Step 4: Configure IPv6 addressing on Serial0/0/0.


    a. Enter the commands necessary to move to interface configuration mode for Serial0/0/0.
    b. Refer to the Addressing Table for the correct IPv6 address.
    c. Configure the IPv6 address, the link-local address and activate the interface.

    Step 5: Verify IPv6 addressing on R1.


    It is good practice to verify addressing when it is complete by comparing configured values with the values in
    the addressing table.
    a. Exit configuration mode on R1.
    b. Verify the addressing configured by issuing the following command:
    R1# show ipv6 interface brief
    c. If any addresses are incorrect, repeat the steps above as necessary to make any corrections.
    Note: To make a change in addressing with IPv6, you must remove the incorrect address or else both the
    correct address and incorrect address will remain configured on the interface.
    Example:
    R1(config-if)# no ipv6 address 2001:db8:1:5::1/64
    d. Save the router configuration to NVRAM.
    Close a configuration window

    Part 2: Configure IPv6 Addressing on the Servers


    Step 1: Configure IPv6 addressing on the Accounting Server.
    a. Click Accounting and click the Desktop tab > IP Configuration.
    b. Set the IPv6 Address to 2001:db8:1:1::4 with a prefix of /64.
    c. Set the IPv6 Gateway to the link-local address, fe80::1.

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 3 www.netacad.com
    Packet Tracer - Configure IPv6 Addressing

    Step 2: Configure IPv6 addressing on the CAD Server.


    Configure the CAD server with addresses as was done in Step 1. Refer to the Addressing Table for the
    addresses to use.

    Part 3: Configure IPv6 Addressing on the Clients


    Step 1: Configure IPv6 addressing on the Sales and Billing Clients.
    a. Click Billing and then select the Desktop tab followed by IP Configuration.
    b. Set the IPv6 Address to 2001:db8:1:1::3 with a prefix of /64.
    c. Set the IPv6 Gateway to the link-local address, fe80::1.
    d. Repeat Steps 1a through 1c for Sales. Refer to the Addressing Table for the IPv6 address.

    Step 2: Configure IPv6 Addressing on the Engineering and Design Clients.


    a. Click Engineering and then select the Desktop tab followed by IP Configuration.
    b. Set the IPv6 Address to 2001:db8:1:2::3 with a prefix of /64.
    c. Set the IPv6 Gateway to the link-local address, fe80::1.
    d. Repeat Steps 2a through 2c for Design. Refer to the Addressing Table for the IPv6 address.

    Part 4: Test and Verify Network Connectivity


    Step 1: Open the server web pages from the clients.
    a. Click Sales and click the Desktop tab. Close the IP Configuration window, if necessary.
    b. Click Web Browser. Enter 2001:db8:1:1::4 in the URL box and click Go. The Accounting website
    should appear.
    c. Enter 2001:db8:1:2::4 in the URL box and click Go. The CAD website should appear.
    d. Repeat steps 1a through 1c for the rest of the clients.

    Step 2: Ping the ISP.


    a. Click on any client.
    b. Click the Desktop tab > Command Prompt.
    c. Test connectivity to the ISP by entering the following command:
    PC> ping 2001:db8:1:a001::1
    d. Repeat the ping command with other clients until full connectivity is verified.
    End of Document

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 3 www.netacad.com

    You might also like