IMPORTANT:

THESE INSTRUCTIONS ARE TO REMAIN

WITH THE HOMEOWNER
SAVE THESE INSTRUCTIONS

INSTALLATION
AND OPERATING
INSTRUCTIONS
SERIAL #

SAFETY NOTICE:
If this stove is not properly installed, a
house fire may result. For your safety, follow
the installation instructions. Contact local
building or fire officials about restrictions
and installation inspection requirements in
your area.

TESTED and LISTED

to ULC S627 / UL 1482
Meets the U.S. Environmental Protection
Agency's May 2020 Cribwood Particulate
Emission Standards

MODEL: TN20
SERIES: B

110618-28 ©PACIFIC ENERGY FIREPLACE TN20.B 100000064

PRODUCTS LTD. - 2018
 Contents
Specifications ............................................................................. 3 Stove Dimensions .................................................................... 11
Efficiency and BTU Output.................................................. 3 Residential Installation ............................................................. 11
Safety and Maintenance ............................................................. 4 Residential Clearances...................................................... 12
Maintenance Checks .................................................................. 5 Crate Removal.................................................................. 12
Weekly:................................................................................ 5 Ember Protection ..................................................................... 13
Monthly............................................................................... 5 Securing Bracket Installation:........................................... 13
As Needed........................................................................... 5 Procedure:......................................................................... 14
When Cleaning the Chimney System:................................. 5 Through Wall Installations ................................................ 17
Blower:................................................................................ 5 Mobile Home Installation .......................................................... 19
Chimney Smoke and Creosote Formation.......................... 6 Mobile Home Clearances.................................................. 19
Chimney Fires..................................................................... 6 Installation......................................................................... 19
To Avoid a Chimney Fire..................................................... 7 Procedure:......................................................................... 19
In the event of a Chimney Fire............................................ 7 Combustion Air ......................................................................... 20
Operation .................................................................................... 8 Leg Model......................................................................... 20
Wood Selection................................................................... 8 Baffle Board / Tube Installation ................................................ 21
DO NOT BURN:................................................................... 8 Removal............................................................................ 21
How to Test Your Wood....................................................... 9 Installation......................................................................... 21
Lighting a Fire...................................................................... 9 Optional Blower ........................................................................ 22
Normal Operation................................................................ 9 Blower Installation............................................................. 22
Restarting After Extended or Overnight Burns................. 10 Blower Operation.............................................................. 22
Proper Draft....................................................................... 10 Firebrick Installation ................................................................. 23
Curing of the Paint Finish.................................................. 10 Troubleshooting ........................................................................ 24
Ash Removal..................................................................... 10 Replacement Parts ................................................................... 25
Disposal of Ashes............................................................. 10 Rating Label ............................................................................. 26
Heat Output....................................................................... 10 Rating label location.......................................................... 26

! WARNING HOT GLASS WILL CAUSE

BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.

PLEASE SAVE THESE INSTRUCTIONS

This manual describes the installation and operation of the True North, TN20 Series B Freestanding wood heater.
This heater meets the 2020 U.S. Environmental Protection Agency's crib wood emission limits for wood heaters
sold after May 15, 2015. Under specific test conditions this heater has been shown to deliver heat at rates rang-
ing from 13,150 to 28,350 Btu/hr.

NOTE: WE STRONGLY RECOMMEND THAT SMOKE AND CARBON MONOXIDE DETECTORS BE INSTALLED IN
THE AREA WHERE THE HEATER IS TO BE INSTALLED.
If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be
due to curing of stove paint or fumes caused by accidentally leaving the fire door open. Do not disconnect the detectors.

SAFETY NOTICE: If this stove is not properly installed, a house fire may result. For your safety, follow the instal-
lation instructions. Contact local building or fire officials about restrictions and installation inspection require-
ments in you area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result
in property damage, bodily injury, or even death.

2 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Specifications
Efficiency and BTU Output

EPA Certified Emissions 1.6 grams per hour

LHV Tested Efficiency 1 78%
HHV Tested Efficiency 2 72.7%
EPA BTU Output 3 13,900 to 29,200 btu/hr
Peak BTU/Hr Output 4 55,000
Maximum Wood Length 20 inches
Ideal Wood Length 18 inches
Fuel Seasoned Cord wood

1 Weighted Average Lower Heating Value (LHV) efficiency as

tested using CSA B415 Performance testing of solid-fuel-
burning heating appliances. LHV assumes the moisture is
already in a vapour state so there is no loss of energy
2 Weighted Average Higher Heating Value (HHV) efficiency
as tested using CSA B415 Performance testing of solid-fuel-
burning heating appliances. HHV includes the energy required
to vaporize the water in the fuel
3 The range of BTU outputs is based on efficiency using CSA
B415 Performance testing of solid-fuel-burning heating appli-
ances and burn rates from the low and high EPA tests using
Douglas Fir dimensional lumber.
4 The Peak BTU/hr is based on efficiency using CSA B415
Performance testing of solid-fuel-burning heating appliances,
the Maximum one hour High burn rate from the High Burn EPA
test and the BTU content of cord wood (8600 btu/lb).

Experience will give you the right settings for proper combustion
and efficient burning for the wood you are using. Remember the
correct air inlet setting is affected by variables such as type of
wood, outside temperature, chimney size and weather conditions.
With practice, you will become proficient in operating your heater
and will obtain the performance for which it was designed.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 3

PRODUCTS LTD.
 Safety and Maintenance
WARNING: Never use chemicals or any other ­volatile liquid to start a fire. Do not burn garbage, or
­flammable fluids such as gasoline, naptha, or engine oil.

WARNING: ONLY USE MATERIALS SUPPLIED BY MANUFACTURER WHEN DOING MAINTENANCE OR

REPLACEMENTS.

1. Burn only dry and well seasoned cord wood. The denser or heavier the wood when dry, the greater its
heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup
of creosote. If you feel it is necessary to burn wet or unseasoned wood, do so only with the air inlet set
open enough to maintain a good strong fire and fairly high chimney temperatures. Do not attempt to burn
overnight using green wood or wet wood. Wet wood can cause up to 25% drop in heater output, as well
as contributing significantly to creosote buildup.

2. Remove ashes frequently. Embers can roll out the door and create a fire hazard. Maintain a 1"(25mm)
minimum ash base.

3. If glass becomes darkened through slow burning or poor wood, it can readily be cleaned with fireplace
glass cleaner when stove is cold. Never scrape with an object that might scratch the glass. The type and
amount of deposit on the glass is a good indication of the flue pipe and chimney buildup. A light brown
dusty deposit that is easily wiped off usually indicates good combustion and dry, well-seasoned wood and
therefore relatively clean pipes and chimney. On the other hand, a black greasy deposit that is difficult to
remove is a result of wet and green wood and too slow a burning rate. This heavy deposit is building up at
least as quickly in the chimney.

4. DOOR GASKETS - The gasket used for the True North (5/8"(16mm) medium density fiberglass rope)
requires only light pressure to seal. This will prolong seal life. It is important that the door seal be main-
tained in good condition. P­ eriodically inspect seals and replace if necessary. Follow instructions included
in the Gasket kit obtainable from your nearest True North dealer.

5. DOOR GLASS - Do not slam loading door or otherwise impact glass. When closing door, make sure that
no logs protrude to impact the glass. If the glass gets cracked or broken, it must be replaced before using
the stove. Replacement glass can be obtained from your dealer. Use 9-1/4"(235mm) x 13-1/4"(337mm) x
5 mm. Ceramic glass only. Do not substitute with any other type.

• -To remove broken glass, undo the four retaining screws and remove clamps, noting ­position for
­re-assembly. ­Remove all particles of glass. Be careful as they are very sharp. Install new glass complete
with gasket. Replace clamps and screws.

CAUTION:

- do not overtighten, tighten screws very carefully

- do not clean glass when hot
- do not use abrasive cleaners on glass

6. The area where boost combustion air enters the firebox must be kept clear of excessive ash buildup
which will block air flow. This area is at the front of the firebox.

7. Do not store wood within heater installation ­clearances, or within the space required for fuel loading
and ash ­removal. Keep the area around the heater clean and free of loose combustibles, furniture,
newspapers, etc.

4 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
8. Establish a routine for the fuel, woodburning and Lighting techniques. Check daily for creosote buildup in
the firebox, until you are ­experienced and are operating the stove cleanly and safely.

9. Be aware that the hotter the fire, the less creosote is deposited. More frequent chimney cleaning may be
necessary in mild weather or when burning "wet" or ubseasoned wood.

10. Instruct all members of your family on the safe ­operation of the heater. Ensure they have enough
knowledge of the entire system if they are expected to operate it. Stress the section on chimney fires and
the importance of following the steps outlined "In Case of Chimney Fire".

Maintenance Checks
Check the following parts for damage such as cracks, excessive corrosion, burned out sections and exces-
sive warping:

Weekly:

• Firebrick - Visual, for cracking.

• Door Gasket - sagging, placement, damage.

Monthly

• Brick rail tabs and brick rails.

• Back side of airwash chamber.
• Boost tube cover.
• Top baffle board.
• Baffle Tubes.

As Needed

• It is recommeded that the chimney be inspected a minimum of every 2 months and cleaned as needed a
minimum of 2 times a year.

When Cleaning the Chimney System:

• Top heat shield and mounting bolt.

• Brick Rails.
• Manifold.

- Replace the baffle tubes if they show signs of cracking or breakage.

- Please contact your Dealer for replacement parts if you experience any of the damage listed above.
Continuing to operate your stove with broken parts may accelerate damage to other parts and will void your
warranty

Blower:

• The blower should be cleaned out a minimum every six months by using a vacuum on the grill openings in
the back and bottom of the blower casing to remove any dust and debris.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 5

PRODUCTS LTD.
Chimney Smoke and Creosote Formation
When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled
moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow
burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes
an extremely hot fire. The chimney connector and chimney should be inspected periodically (at least once
every two months) during the heating season to determine if a creosote buildup has occurred. If creosote has
accumulated (3 mm. or more), it should be removed to reduce the risk of a chimney fire.

1. Highest smoke densities and emissions occur when a large amount of wood is added to a bed of hot
coals and the air inlet is closed. The heated wood generates smoke, but without ample air, the smoke
cannot burn. Smoke-free, clean burning requires small fuel loads, two or three logs at a time or 1/4 to 1/2
of fuel load and leaving the air inlet relatively wide open, especially during the first 10 to 30 minutes after
each loading, when most of the smoke generating reactions are occurring. After 30 minutes or so, the air
inlet can be turned down substantially without excessive smoke generation. Wood coals create very little
creosote-producing smoke.

2. The cooler the surface over which the wood smoke is passing, the more creosote will be condensed.
Wet or green wood contributes significantly to ­creosote formation as the excess moisture that is boiled
off cools the fire, making it difficult for the tars and gases to ignite, thus creating dense smoke and poor
­combustion. This moisture-laden smoke cools the chimney, ­compounding the problem by offering the
smoke the ideal place to condense.

In summary, a certain amount of creosote is inevitable. Regular inspection and cleaning is the solution. The
use of dry, seasoned wood and ample combustion air will help to minimize annoying smoke emissions and
creosote buildup.

Chimney Fires
The dangerous side effect of excessive creosote buildup is a chimney fire. This causes much higher than
normal temperatures in the chimney and on its exterior surfaces. Temperatures inside the chimney can
exceed 2000°F (1100°C). Ignition of nearby or touching combustible material is more likely during a chimney
fire. Proper clearances are critical to prevent damage during such a fire.

Chimney fires are easy to detect; they usually involve one or more of the following:

• Flames and sparks shooting out of the top of the ­chimney

• A roaring sound

• Vibration of the chimney

6 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
To Avoid a Chimney Fire
1. Burn wood cleanly. Do not burn wet wood or turn down the unit too quickly after loading.

2. Do not let creosote build up to a point where a chimney fire is possible.

3. Do not have fires in the heater that may ignite ­chimney fires. These are excessively hot fires, such as when
burning household trash, cardboard, Christmas tree limbs, or even ordinary fuel wood; (eg. with a full load
on a hot bed of coals and with the air inlet wide open for more time than is needed to completely char a
fresh fuel load.)

4. The Chimney and connector pipe should be inspected /cleaned periodicaly.

In the event of a Chimney Fire

Have a fire extinguisher handy. Contact your local. municipal or state/provincial fire authority for further
information on how to handle a chimney fire. It is most important that you have a clearly understood plan
on how to handle a chimney fire.

1. Close down the air inlet on the stove.

2. Call the local fire department.

3. Prepare to evacuate to ensure everyone's safety. Have a well understood plan of action for evacuation.
Have a place outside where everyone is to meet.

4. After the chimney fire is out, the chimney must be cleaned and checked for stress and cracks before
­starting another fire. Also check combustibles around the chimney and the roof. The services of a
­competent or certified installer, ­(certified by the Wood Energy Technical Training program (WETT) - in
Canada, National Fireplace Institute (NFI) - in U.S.A., are strongly r­ ecommended.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 7

PRODUCTS LTD.
 Operation
CAUTION: Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin
burns.

WARNING: Always keep loading door closed when burning. This heater is not designed for open door
burning.

WARNING: No alteration or modification of the combustion air control assembly is permitted. Any
tampering will void warranty and could be very ­hazardous.

WARNING: Do not use grates or andirons to elevate the fuel. Burn directly on the fire bricks. Replace
broken or missing bricks. Failure to do so may ­create a hazardous condition.

WARNING: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar
liquids to start or ‘freshen up’ a fire in this heater. Keep all such liquids well away from the heater while
in use.

Your True North heater is designed for maximum overall efficiency at a moderate firing rate. Over firing the
appliance will shorten the life of the product. Failure to rectify an over firing condition can be hazardous
and may void the manufacturer's warranty. Too slow a burn may contribute to ­creosote buildup and lowers
combustion efficiency.

Wood Selection
This heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when
burning air-dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

Wood should be properly air dried (seasoned) for six months or more. Wet or undried wood will cause
the fire to smoulder and produce large amounts of smoke and creosote. Wet wood also produces very
little heat and tends to go out often. Wood should be stored under cover away from open flame or heat
sources.

DO NOT BURN:
• Salt water wood * • Treated wood
• Wet or green wood • Coal/charcoal
• Garbage* • Solvents
• Lawn clippings/yard waste • Unseasoned wood
• Railroad ties • Manure or animal remains
• Materials containing rubber, including tires • Materials containing plastic
• Waste petroleum products, paints or paint thin- • Materials containing asbestos
ners, or asphalt products
• Construction or demolition debris • Paper products, cardboard, plywood, or
particleboard.

* These materials contain chlorides which will rapidly destroy metal surfaces and void warranty.

Burning these materials may result in the release of toxic fumes or render the heater ineffective and cause
smoke.

8 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
The prohibition against burning these materials does not prohibit the use of fire starters made from paper,
cardboard, saw dust, wax and similar substances for the purpose of starting a fire in an affected wood heater.

Do not burn anything but cordwood. Other fuels, eg. ­charcoal, can produce large amounts of carbon
­monoxide, a t­ asteless, odourless gas that can kill. Under no ­circumstances should you attempt to barbecue
in this heater.

How to Test Your Wood

Add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more
than one side within one minute. It is damp if it turns black and lights within three minutes. If it sizzles, hisses
and blackens without igniting in five minutes it is soaked and should not be burned.

Lighting a Fire
Remove the retaing clip on the front of the baffle before lighting for the first time.

1. Move air control lever to the left-most position ­(maximum firing rate) and open door.

2. Place crumpled newspaper in the centre of the heater and criss-cross with several pieces of dry kindling.
Add a few small pieces of dry wood on top.

3. Ignite the paper and leave the door ajar approimately 1/2"(13mm) - 1"(25mm) until the wood kindling is
fully engulfed in flame. DO NOT LEAVE UNATTENDED.

4. After the kindling is fully engulfed add a few small logs. Close door.

5. Begin normal operation after a good coal base exists and wood has charred.

Normal Operation
WARNING: This wood heater has a manufacturer-set minimum low burn rate that must not be altered.
It is against federal regulations to alter this setting or otherwise operate this wood heater in a manner
inconsistent with the operating instructions in this manual.

1. Set air control to a desired setting. If smoke pours down across the glass (waterfall effect) this indicates
you have shut the control down too soon or you are using too low a setting. The wide range control panel
makes finding the desired setting for your application easy. As every home's heating needs vary (ie.
insulation, windows, climate, etc.) the proper setting can only be found by trial and error and should be
noted for future burns.

2. To refuel, adjust air control to high, and give the fire time to brighten. Open the door slowly, this will pre-
vent backpuffing.

3. Use wood of different shape, diameter and length (up to 18" (457mm)). Load your wood and try to place
the logs so that the air can flow between them. Always use dry wood.

4. Do not load fuel to a height or in such a manner that would be hazardous when opening the door.

5. For extended or overnight burns, unsplit logs are preferred. Remember to char the wood completely on
maximum setting before adjusting air control for overnight burn.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 9

PRODUCTS LTD.
Restarting After Extended or Overnight Burns
1. Open door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of
embers, close door.

2. Adjust air control to high (control lever to the left) and in just a few minutes, logs should begin burning.

3. After wood has charred, reset air control to desired setting.

4. To achieve maximum firing rate, set air control lever to the left-most position. Do not use this setting other
than for starting or preheating fresh fuel loads.

DO NOT OVERFIRE THIS HEATER: Attempts to achieve heat output rates that exceed heater design
specifications can result in permanent damage to the heater and chimney.

Proper Draft
1. Draft is the force that pulls air into the appliance and up through the chimney. The amount of draft in your
chimney depends on the length of the chimney, local geography, nearby obstructions and other factors.

2. Too much draft may cause excessive temperatures in the appliance. An uncontrollable burn or a glowing
red stove part or chimney indicates excessive draft.

3. Inadequate draft may cause backpuffing into the room and plugging of the chimney. Smoke leaking into
the room through appliance and chimney connector joints indicates inadequate draft.

Curing of the Paint Finish

To achieve the best finish, the paint on your stove must be baked on. Follow the Paint Curing instructions.
When burning your stove for the first 2-3 times it is very important that the room be well ventilated. Open
all windows and doors. Smoke and fumes caused by the curing process may cause discomfort to some
individuals.

Ash Removal
Caution: Ashes are to be removed only when the heater is cold. Whenever ashes get 3"(76mm) to 4"(102mm)
deep in your firebox, and when fire has burned down and cooled, remove excess ashes. Leave an ash bed
approximately 1" (25 mm) deep on the firebox bottom to help maintain a hot charcoal bed.

Disposal of Ashes

Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be
placed outside on a non-combustible floor or on the ground, well away from all combustible materials, pend-
ing final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be
retained in closed container until all cinders have thoroughly cooled. Other waste should not be placed in this
container.

Heat Output

Experience will give you the right settings for proper combustion and efficient burning. Remember that the
correct air inlet setting is affected by variables such as type of wood, outside temperature, chimney size and
weather conditions. With practice, you will become proficient in operating your heater and will obtain the
performance for which it was designed.

10 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Stove Dimensions
28 3/4" 28 3/4"
21 5/8" 730 mm 21 5/8" 730 mm
549 mm 23 7/8" 549 mm 23 7/8"
606 mm 606 mm

28 1/8" 26 1/4" 28 1/8" 28 1/8" 26 1/4" 28 1/8"

714 mm 667 mm 714 mm 714 mm 667 mm 714 mm

Figure 1:  TN20B Dimensions.

Residential Installation
Warning: Under no circumstances is this heater to be ­installed in a makeshift or "temporary" manner. It
may be fired only after the following conditions have been met.

• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

• DO NOT INSTALL IN A SLEEPING ROOM.

• THIS ROOM HEATER MUST BE CONNECTED TO:

1. A CHIMNEY LISTED TO: UL 103HT (USA) or ULC-S629 (CANADA) or
2. A CODE APPROVED MASONRY CHIMNEY WITH A LISTED FLUE LINER.

• DO NOT ATTEMPT TO CONNECT THIS HEATER TO ANY AIR DISTRIBUTION DUCT.

• The services of competent installer are strongly ­recommended.

• Outside combustion air or fresh air into the room may be required in your area, consult local building
codes (see Combustion Air section).

NATIONAL We recommend that our products be

FIREPLACE
INSTITUTE
installed and serviced by professionals
who are certified in the U.S. by the
National Fireplace Institute (NFI)
or in Canada by Wood
Energy Technical Wood Energy
Technical Training
CERTIFIED Training (WETT) www.wettinc.ca
www.nficertified.org

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 11

PRODUCTS LTD.
Crate Removal
1. Carefully remove wood top and supports.

2. Remove plastic cover.

3. Remove all screws holding the Legs or Pedestal, to the Pallet.

Residential Clearances
• BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE 6"(150mm) DIAMETER AND LISTED TO:
CANADA - CONNECTOR - LISTED to ULC S-641 and CHIMNEY LISTED to ULC-S-629
USA - CONNECTOR AND CHIMNEY LISTED to UL-103 HT

1. Residential Clearances to Combustible surfaces and materials;

This heater may be installed using a single-wall c­ onnector (smoke pipe) as per local and National fire and
Installation codes. see Single wall Connector in figue 2. Clearances may be reduced with various heat
shielding or insulating materials. Consult local and national fire codes and authorities for approval

For close clearances, use a listed double-wall c
­ onnector, See (Figure 2). "Double Wall Connector

Mobile Home installation see "Mobile Home Installation"Figure 8 on page 19.

Minimum Clearance to Combustibles

Single Wall Connector - Residential

12" 8"
18 3/8"
305mm 203mm
467mm 19"
12" 483mm
305mm

22 3/4” 8"
578mm 203mm
Double Wall Connector - Residential

11 3/8" 5" 11 3/8" 5"

289mm 127mm 289mm 127mm

14" 3"
8" 8" 355mm 76mm
8"
203mm 203mm 203mm

18 3/4" 18 3/4"
476mm 476mm
3"
Alcove: Min. Height 7' [2.13m]
76mm
Max. Depth 3' [915mm]

Figure 2:  TN20B clearances.ai

12 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Ember Protection
The stove may be installed on a combustible floor, provided ember protection (UL 1618 type 1 )made from a
non-combustible material (a minimum K value of 23.7 btu/ft h ° F) the equivelent of 20 Gauge steel or tile is
used.

This protection must extend as follows:

In Canada: 18" (457 mm)from the loading door on the firing side and 8" (203 mm) from the sides. See Figure
3, below.

In USA: 16" (406 mm) to the front of the firebox and 8" (203 mm) from the sides of the fuel loading door
opening. See Figure 4, below. This protection is also required under a horizontal chimney connector and 2"
(51 mm) beyond each side of it.

Canada Only United States Only

Minimum width: 37 5/8” (956 mm) Minimum width: 28 3/4” (730 mm)
Minimum overall depth: 50” (1.27 m) Minimum overall depth: 40” (1.016 m)

8” [203 mm]
Non-combustible Non-combustible
ember protector floor protector
8” [203 mm]
8” [203 mm]

8“ [203 mm]

8” [203 mm]
18” [457 mm] 16” [406 mm]

Figure 3:  TN20B Floor protector Canada. Figure 4:  TN20B Floor protector U.S..

Securing Bracket Installation:

These will be needed to anchor the stove in a

mobile home instalation and are recomended when
installing combustion air to prevent movement
of the unit and seperation of the combustion air
intake.

1. The hold down backets are provided in a bag

with the unit. Insert the brackets by sliding
them through the slots in the rear legs. Then lag
the bracket to the floor or hearth pad.
Figure 5:  Securing bracket.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 13

PRODUCTS LTD.
Procedure:

Follow the chimney manufacturer's instructions, The installation instructions included below are just
general steps.

1. Position stove and floor protection (with hole for combustion air if required) in accordance with the
clearances as stated on the label and in Figure 7 on page 16.

2. Mark the position for the hole in the ceiling and roof by using a string and plumb-bob.

3. Check that the intended location will not interfere with floor joists, ceiling joists or rafters before
proceeding further.

• Cut a hole in the ceiling and roof to suit the chimney system and frame in the sides.

• install roof or ceiling support as required in the installation.

• Install the roof flashing, be sure to secure the flashing and seal with the appropiate sealant as per
instructions

• Assemble the chimney sections so the finished length is resting on the support and protruding through
the roof. Install the radiation shield. Avoid having chimney joints between ceiling and roof.

• install the storm collar and required chimney sections to acheive a safe height. Attach rain cap and
check system for leaks.

4. If double-wall connector pipe is to be connected between the stove and the listed insulated chimney,
• Use listed double-wall connector and install all components to the connector pipe manufacturer's
installation requirements.

5. If smoke pipe is being used to connect between the stove and the listed insulated chimney,
• As short and straight as possible, use 6"(150mm) diameter, minimum 24 gauge black pipe, that is clean
and in new condition.
Install the smoke pipe (chimney connector), crimped edge of the pipe down and inside the stove's collar.
This will carry any liquid creosote or condensation back into the stove. Use holes provided in stove
collar to secure pipe with three screws.

• Install the remaining lengths of pipe, one on top of the other to the finished height of the listed insulated
chimney adapter and secure to each other. A slip-section will make attaching the smoke pipe to the
chimney sytem adapter easier. secure with 3 screws at each joint.

• The Smoke pipe/chimney connector shall not pass through an attic, roof space, closet or similar
concealed space, or a floor, or ceiling. Where passage through a wall, or partition of combustible
material is desired, the installation shall conform to CAN/CSA-B365, INSTALLATION CODE FOR
SOLID-FUEL-BURNING APPLIANCES AND EQUIPMENT or NFPA 211 STANDARD FOR CHIMNEYS,
FIREPLACES AND SOLID FUEL BURNING APPLIANCES

14 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Spark arrestor rain cap

The chimney may incorporate

an offset. To do this safely, all
sections of listed connector,
offset elbows and chimney 3‘ (914 mm)
Minimum
section must be screwed
together by at least three sheet Listed Insulated
Chimney
metal screws per joint. The
chimney must be suitably
supported by the chimney
Storm Collar
manufacturer's listed offset
support. And all vent Roof flashing
manufacturer or national fire
code clearances to
combustible must be observed.
Radiation
shield

Chimney
Minimum 7’ (2.1 m) support
Ceiling hight 57 3/4 “ (1468 mm)
Minimum
Chimney
connector

Combustibles 48”
in front of the (1219 mm)
unit

Non-combustible
Ember protector
Hooded vent or 90°
elbow turned down

* 4” (100 mm) diameter air inlet

with rodent screen.

* If the crawl space is well ventilated

it is not necessary to extend air inlet
to outside.

Figure 6:  Mobile home or typical home installation.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 15

PRODUCTS LTD.
Connecting to a masonry chimney

Ensure that the chimney is in good condition and meets local building codes. Your stove may work better if
the chimney is fully lined with a stainless steel liner, this is because the liner will retain heat and promote draft.
The chimney flue or liner should be the same size as the stove outlet for optimal performance. Reducing or
increasing the flue size may adversely affect stove performance. Chimney flue exit is to be 3 feet (1 m.) above
the roof and two feet (0.6 m.) above highest projection within 10 feet (3 m.). The installation must meet all
local codes. Do not connect this unit to a chimney flue serving another appliance. Minimum system height is
12 feet (3.0 m.) (measured from top of appliance).

Fireclay Flue Liner

Concrete Cap
Ensure that the Masonry chimney
meets all National Fire Protection
Association and local building codes.
Have the chimney cleaned and Chimney
inspected by a professional to ensure
there are no cracks, weak mortar or
other signs of deterioration. See pipe
manufactuers installation instructions
for further information

Minimum Ceiling
Height 7’ (2.1 m)
Approved Through
Wall Installation
57 3/4” (1467 mm)
Minimum

Chimney
Connector

Combustibles in 48”
front of the unit (1219 mm)

Non-combustible
Ember Protector

* 4"(100mm) diameter air inlet with rodent screen

Hooded vent or 90°
* If the crawl space is well ventilated it is not necessary elbow turned down.
to extend air inlet to outside

Figure 7:  Venting to a masonry chimney.

16 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
Through Wall Installations
(as per NFPA 211-2013)
ATTENTION: VAPOUR BARRIER MUST BE ­
MAINTAINED WHEREVER CHIMNEY OR OTHER COMPONENTS PENETRATE TO THE EXTERIOR
OF THE STRUCTURE. SEE LOCAL BUILDING CODES FOR PROPER AND APPROVED METHODS OF
MAINTAINING VAPOUR BARRIER.

System A. Minimum 3.5 in. (90 mm) thick brick masonry wall framed into combustible wall with a minimum
of 12 in. (305 mm) brick separation from clay liner to combustibles. Fireclay liner (ASTM C 315, Standard
Specifications for Clay Fire Linings, or equivalent), minimum 5/8 in. (16 mm) wall thickness, shall run from
outer surface of brick wall to, but not beyond, the inner surface of chimney flue liner and shall be firmly
cemented in place.

Clearance 12 in. (305mm)

Minimum chimney clearance

SYSTEM A to brick and combustibles
2” (51 mm).

Minimum clearance
12” (305 mm) of brick
Chimney flue

Chimney connector

Fireclay liner
Minimum 12” (305 mm)
to combustibles Masonry chimney
constructed to NFPA 211

System B. Solid-Insulated, listed factory-built chimney length of the same inside diameter as the chimney
connector and having 1 in. (25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air space between
the outer wall of the chimney length and combustibles.

The inner end of the chimney length shall be flush with the inside of the masonry chimney flue and shall be
sealed to the flue and to the brick masonry penetration with non-water-soluble refractory cement. Supports
shall be securely fastened to wall surfaces on all sides.

Fasteners between supports and the chimney length shall not penetrate the chimney liner.

Clearance 9 in. (229mm)

Minimum chimney clearance

SYSTEM B from masonry to sheet steel
supports and combustibles
2” (51 mm) Minimum clearance
9” (229 mm)
Nonsoluble
Factory built refractory
chimney length cement
Chimney connector
Chimney length
Use chimney
flush with inside
manufacturers’ parts to
of flue
attach connector
Air space: Chimney securely
9” (229 mm) min. flue
Solid-insulated, listed
Masonry chimney factory built chimney
constructed to NFPA 211 length
Sheet steel supports

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 17

PRODUCTS LTD.
System C. Sheet steel chimney connector, minimum 24 gauge [0.024 in. (0.61 mm)] in thickness, with a
ventilated thimble, minimum 24 gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4 mm) air
channels, separated from combustibles by a minimum of 6 in. (152 mm) of glass fiber insulation. Opening
shall be covered, and thimble supported with a sheet steel support, minimum 24 gauge [0.024 in. (0.61 mm))]
in thickness.

Supports shall be securely fastened to wall surfaces on all sides and shall be sized to fit and hold chimney
section. Fasteners used to secure chimney section shall not penetrate chimney flue liner.

Clearance: 6 in. (152mm)

SYSTEM C
Minimum chimney clearance
from masonry to sheet steel supports
and combustibles 2” (51 mm) Two ventilated air channels,
each 1” (25.4 mm)

Chimney flue
Chimney connector

Minimum 6” (152 mm)

glass fiber insulation
Two ventilated air channels,
each 1” (25.4 mm); Masonry chimney Sheet steel supports
construction of sheet steel constructed to NFPA 211

System D. Solid-Insulated, listed factory-built chimney length with an inside diameter 2 in. (51 mm) larger
than the chimney connector and having 1 in. (25.4mm) or more of insulation, serving as a pass-through for a
single-wall sheet steel chimney connector of minimum 24 gauge [0.024 in. (0.61 mm)] thickness, with a mini-
mum 2 in. (51 mm) air space between the outer wall of chimney section and combustibles.

Minimum length of chimney section shall be 12 in. (305 mm). Chimney section concentric with and spaced 1
in. (25.4 mm) away from connector by means of sheet steel support plates on both ends of chimney section.
Opening shall be covered, and chimney section supported on both sides with sheet steel supports of mini-
mum 24 gauge [0.024 in. (0.61 mm)] thickness.

Supports shall be securely fastened to wall surfaces on all sides and shall be sized to fit and hold chimney
section. Fasteners used to secure chimney section shall not penetrate chimney flue liner.

Clearance: 2 in. (51mm)

SYSTEM D

Minimum chimney clearance

to sheet steel supports
and combustibles 2” (51 mm)
Sheet steel
supports Minimum clearance 2” (51 mm)

Chimney 1” (25.4 mm) air space to

chimney length
Chimney flue

section

Chimney
connector
Chimney connector

Air space: Chimney length

2” (51 mm) min. Sheet steel supports
Masonry chimney
constructed to NFPA 211

18 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Mobile Home Installation
Warning: Under no circumstances is this heater to be installed in a makeshift or "temporary" manner. It
may be fired only after the following conditions have been met.

• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

• DO NOT INSTALL IN A SLEEPING ROOM.

THIS HEATER MUST BE INSTALLED WITH LISTED DOUBLE-WALL CONNECTOR. BOTH CHIMNEY
SYSTEM AND CONNECTOR MUST BE 6"(150mm) DIAMETER AND LISTED TO:
IN CANADA - ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY,
IN USA - UL-103 HT LISTED CONNECTOR AND CHIMNEY

• Outside combustion air supply must be used for Mobile Home instalations see page 20

Mobile Home Clearances

11 3/8" 5" Double Wall Connector - Mobile Home

289mm 127mm

3"
14" 76mm
8" 355mm
203mm

3"
18 5/8" 76mm
473mm

Figure 8:  TN20 Mobile home clearances.

Installation

Minimum chimney height from top of unit is 12' (3.66 m) or as per chimney manufacturers roof
clearances whichever is greater.

NOTE: Longer chimney lengths and different pitch flashings may be used. Install all components to the
connector or chimney manufacturer's installation requirements. Consult your chimney supplier for installation
advice.

Procedure:
Follow Chimney Manufacturer's Installation Instructions
WARNING: THE STRUCTURAL INTEGRITY OF THE ­MOBILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE M
­ AINTAINED.

Note: See "Combustion Air" on page 20.

• Attach stove to floor using two 1/4" x 1" or longer lag screws.
If installing a leg model, insert anchor tabs into slot on bottom of two rear legs and secure to floor with
1/4" x 1" or longer lag screws (Figure 5).

• If installing the Optional Blower Kit the unit must be grounded to the mobile home.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 19

PRODUCTS LTD.
 Combustion Air
Combustion air can be supplied to the stove in one of two ways. Consult your local building code or CAN/
CSA-B365, or NFPA 211

Pedestal Model

1. Direct outside air supply - (Necessary for mobile home installation, optional for residential installation.)

• To draw outside air through the floor; leave the knockout or square cover plate in the rear of the pedes-
tal in place. Use an approved 4"(102mm) inlet vent cap. Cut or drill a 4"(100mm) diameter or larger hole
in the floor anywhere inside the perimeter of the pedestal base. Cover the hole with a 20GA wire mesh
minimum, rodent screen and staple/nail in place. This hole must get its air from a ventilated crawl space
or be extended with duct to the outdoors (see Figure 6 on page 15 or Figure 7 on page 16

• To draw air from behind the stove. Cut or drill a corresponding hole in the closest exterior wall. Install an
approved 4"(102mm) inlet vent cap. Attach the outside air adapter (OAIR.1B) to the back of the pedes-
tal. Connect the adapter to the inlet vent cap using 4"(100mm) fexible or rigid metal venting. . Provide
water protection as required.

2. Room air supply - Remove the knockout or cover plate from the rear of the pedestal enclosure. The stove
will now draw its air from the room through this opening and into the firebox intake

Leg Model

1. Direct outside air supply - (Necessary for mobile home installation, optional for residential installation.)

• To draw outside air through the floor; Cut or drill a 4"(100mm) diameter or larger hole in the floor under
the stove. Attach the outside air adapter (OAIR.1B) to the underside of the stove. Connect the adapter
to the hole using 4"(100mm) fexible or rigid metal venting. Cover the hole with a 20GA wire mesh mini-
mum, rodent screen and staple/nail in place. This hole must get its air from a ventilated crawl space or
be extended with duct to the outdoors (see Figure 6 on page 15 or Figure 7 on page 16. if extended
use an approved 4"(102mm) inlet vent cap

• To draw air from behind the stove. Cut or drill a corresponding hole in the closest exterior wall. Install
an approved 4"(102mm) inlet vent cap. Attach the outside air adapter (OAIR.1B) to the underside of the
stove. Connect the adapter to the inlet vent cap using 4"(100mm) fexible or rigid metal venting. Provide
water protection as required.

2. Room air supply - The stove will draw its air from the room through the opening in the bottom

Note:

The use of outside c­ ombustion air for installation requires the unit to be secured to the structure to prevent
dislodging of the air duct. (See: Securing Bracket Installation page 13)

The living space around the heater must be well ventilated with good air circulation. Anything that may
cause a negative pressure can cause gases or fumes to be pulled into the living area. During extremely cold
weather, and especially when burning at very slow rates, the upper parts of the exposed chimney may ice up,
partially blocking the flue gases. If blockage occurs, flue gases may enter living space.

This unit is not designed to be operated with the firing door open. In addition to the obvious hazard of sparks
landing on combustibles, an open fire door will cause the heater to draw air from the living space and possibly
cause suffocation in an air tight home.
20 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28
PRODUCTS LTD.
 Baffle Board / Tube Installation
The Chimney connector pipe should be disconnected from the woodstove to clean and inspect the chimney.
Only if this is not possible should you remove Baffle Board.

DO NOT OPERATE WITH BAFFLE BOARD INSULATION OR TUBES REMOVED.

Removal
1. With a set of vise-grips, grasp the front baffle tube on the right, slightly away from the baffle air assembly.
While squeezing tightly, use a hammer to hit the pliers and pull the tube to the right to disengage the tube
from the hole on the left. Allow the tube to hang freely from the hole on the right.

2. Repeat step #1 for second baffle tube.

3. Grasp the front edge of the left half of the baffle board and tilt up at the back. Guide the board down and
through the door opening.

4. Grasp the right half of the baffle board and slide it over to the left.

5. Tilt the back of the board up and guide it down and through the door opening.

6. Reverse the process to replace the baffle assembly.

Installation
1. Insert one half of baffle board above the two back baffle tubes inside the firebox, slide over to the right
and allow to rest on the baffle air assembly.

2. Ensure that the second half is inserted to allow the two cuts in the baffle boards to overlap. Insert the
other half of the baffle board and allow to rest on the left side baffle air assembly.

3. With the holes facing forward and the notch to the left side, insert a baffle tube into the hole in the baffle
air channel on the right at an angle and then raise and insert into the opposite hole on the left side baffle
air ­assembly.

4. With a set of vise-grips, grasp the baffle tube on the left, slightly away from the baffle air assembly. While
squeezing tightly, use a hammer to hit the pliers and push the tube to the left to engage the tube in the
hole on the left.

5. Repeat steps #3 & #4 with the remaining baffle tube.

6. Slide the baffle board halves together and then separate slightly to ensure there are no gaps on either side
of the baffle board.

7. Push baffle board tight against the rear of the ­firebox.

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 21

PRODUCTS LTD.
 Optional Blower
The optional blower kit (kit #TRNO.19BLOWA) is equipped with a three prong power cord and may be
installed at any time. Route power supply cord away from heater.

Electrical rating: 115V, 60Hz, 0.5 amps.

Blower Installation
1. Remove the 4 screws and cover plate from the rear shield on the stove (Figure 10).

2. Using the same 4 screws, place the blower into the opening in the rear shield with the blower outlet
­pointing up (Figure 11).

3. Tighten the screws.

Blower Operation
Proper blower speed matched with air control setting will ensure peak performance from your stove. Operate
as follows:

• Except on "High" setting, wait 30 minutes before turning on blower to desired setting.

ELECTRICAL RATING 115V, 60Hz, 0.5A

SPEED
CONTROL

BLOWER

POWER CORD

Figure 9:  Blower Wiring Diagram.

Figure 10:  Remove the cover plate. Figure 11:  Installing the blower.

22 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Firebrick Installation
The package contains 20 full-size firebricks. With the insert in its final position, install the firebricks as follows:

1. Place the first brick up under the rear brick rail (Figure 12) and slide it to either the far left or far right.

2. Place 3 more bricks up under the rear brick rail to complete the rear brick placement (Figure 13).

Brick rails

Figure 12:  Firebox and brick rails. Figure 13:  Bricks against rear wall.jpg

3. Place the floor bricks as shown in Figure 14.

4. On both the right and left sides, place the first side wall brick under the Brick Retainer and on top of the
floor bricks and slide it all the way to the back, so that it is up against the rear wall bricks.

5. Using the same method, place three more bricks along one of the side walls. (Figure 15)

6. Repeat the side wall brick installation on the opposite side to complete the firebrick installation.

Figure 14:  Floor bricks laying lengthwise.jpg Figure 15:  Remaining side wall bricks installation.jpg

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 23

PRODUCTS LTD.
 Troubleshooting

Problem Cause Cure

Glass is Dirty 1. Wood is wet - Use dry wood

2. Turning down air control - Do not turn down until

or damper too soon a) there is a good bed of coals
b) the wood is charred

3. Draft too low - Improper chimney height and / or diameter

- Chimney plugged or restricted, check flue
- Provide outside air for combustion

4. Door gasket leakage - Replace gasket

- Check latch

Excessive Creosote Buildup - See 1, 2, 3, above.

Low Heat Output 1. Wood is wet - Use dry wood

2. Fire too small - Build a larger fire
3. Draft too low - Chimney plugged or restricted, inspect and
clean

Won't Burn Overnight 1. Air control is set too high - Set control lower
2. Not enough wood - Unsplit wood is preferred for overnight burns
3. Draft too high - Excessive chimney height and/or diameter,
see "Proper Draft" on page 10.

Stove Won't Burn 1. Combustion air supply - Check outside air supply for obstruction
blocked - Check that room air cover is removed

2. Draft too low - Chimney plugged or restricted, inspect and

clean
- Chimney oversized or otherwise unsuitable,
consult Dealer

24 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.
 Replacement Parts
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)

The replacement parts are the same for the leg model.
ITEM DESCRIPTION PART NO.
1 Baffle Board (2pcs.).........................................................................80000619
2 Baffle Tube Set (4pcs.).................................................................... 80000615
3a Baffle Air Box, Left (c/w gasket/screws).........................................80002140
3b Baffle Air Box, Right (c/w gasket/screws)....................................... 80002141
3c Baffle Air Box, Gasket with Screws (1 side)....................................80002138
4 Rear Brick Rail.................................................................................80002143
5 Door Casting Assy - No Glass (c/w Handle)................................... 80000621
6 Door and Glass Gasket...................................................................80000600
7 Replacement Glass (c/w clamps/gasket)........................................80000616
8 4 pc Glass Clamp set (c/w screws) ................................................ 80000617
9 Firebrick Set 9” x 4 1/2” x 1 1/4” (20 pcs.)......................................80000620
10 Flame Shield (c/w hardware)........................................................... 80002142
11 Optional Fan ................................................................................... 31140001
11a Blower............................................................................................. 80000905
11b Fan Speed Control..........................................................................80000908
11c Speed Control Knob........................................................................80001509

11
1

4
2 8

10
6
3a

9
3b

110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 25

PRODUCTS LTD.
 26
PRODUCTS LTD.
Rating label location

CERTIFIED FOR CANADA AND U.S.A. - MODEL / MODÈLE: TN20 SERIES / SÉRIE: B DO NOT REMOVE THIS LABEL
LISTED ROOM HEATER, SOLID FUEL TYPE.
ALSO FOR USE IN MOBILE HOMES SN- 411
TESTED TO/ ÉPROUVÉ SELON: CAN/ULC S627-00 AND IN THE USA CONFORMS TO UL 1482-2011
RESIDENTIAL INSTALLATION
• INSTALLEZ ET UTILISEZ SELON LES INSTRUCTIONS D’INSTALLATION ET D’OPÉRATION FOURNI AVEC L’APPAREIL..
ETL#4001507
USING SINGLE WALL CONNECTOR/ • CONTACTEZ LES OFFICIELS DE LA CONSTRUCTION OU DE SERVICE D’INCENDIE POUR DES INFORMATIONS QUANT AUX RES-
• INSTALL AND USE IN ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION AND OPERATING MINIMUM CLEARANCES TO INSTALLATION RÉSIDENTIELLE UTILISANT UN TRICTIONS. PERMIS D’INSTALLATION ET INSPECTIONS DANS VOTRE RÉGION.
INSTRUCTIONS. COMBUSTIBLE MATERIALS/ RACCORD DE MUR SIMPLE • NE RELIEZ PAS CET APPAREIL À UN CONDUIT DE CHEMINÉE DESSERVANT DÉJÀ UN AUTRE APPAREIL
• CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS, INSTALLATION PERMIT AND • UTILISER UN TUYAU DE RACCORDEMENT DE 6 PO (150 MM) DIAM., HOMOLOGUÉ OU NOIR 24 MSG (MIN.)
INSPECTION IN YOUR AREA.
DÉGAGEMENTS MINIMALES AUX A. 12 IN. / 305 MM
B. 12 IN. / 305 MM • PEUT ÊTRE CONNECTÉ À UNE CHEMINÉE DE MAÇONNERIE GAINÉ PRÊTE À L’EMPLOI AVEC DES COMBUSTIBLES SOLIDES.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. MATÉRIAUX COMBUSTIBLES
• N’OBSTRUEZ PAS L’ESPACE SOUS LE CAISSON DU POÊLE

©PACIFIC ENERGY FIREPLACE

• USE 6 INCH / 150MM DIAMETER MINIMUM 24 MSG BLACK OR LISTED CONNECTOR. A. SIDEWALL TO UNIT/ C. 8 IN. / 203 MM • CONSULTEZ LE CODE LOCAL DE CONSTRUCTION ET LES INSTRUCTIONS DU FABRICANT QUANT AUX PRÉCAUTIONS À
• CAN BE CONNECTED TO A LINED MASONRY CHIMNEY SUITABLE FOR USE WITH SOLID FUELS. MUR DE CÔTE / APPAREIL D. 19.5 IN. / 495 MM PRENDRE LORSQUE VOUS FAITES PASSER UNE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉ-
• DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER. B. BACKWALL TO UNIT/ E. 15.25 IN. / 381 MM
MUR DE FOND / APPAREIL RIAUX COMBUSTIBLES.
• SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED C. CORNER TO UNIT/ F. 16 IN. / 432 MM • LE TUYAU DE RACCORDEMENT DE CHEMINÉE NE DOIT PAS TRAVERSER UN MUR OU PLAFOND EN MATÉRIAUX COMBUS-
WHEN PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. COIN / APPAREIL TIBLES.
RESIDENTIAL CLOSE CLEARANCE INSTALLATION
• DO NOT PASS A CHIMNEY CONNECTOR THROUGH A COMBUSTIBLE WALL OR CEILING. D. SIDEWALL TO CONNECTOR/ USING DOUBLE WALL CONNECTOR/ INSTALLATION • DÉGAGEMENT MINIMAL ENTRE UN RACCORDEMENT DE CHEMINÉE À SIMPLE PAROIS ET UN MUR ET TOUT MATÉRIEL COM-
• MINIMUM CLEARANCE BETWEEN SINGLE WALL CHIMNEY CONNECTOR AND COMBUSTIBLE MATE- MUR DE CÔTE / RACCORD RÉSIDENTIELLE AVEC DÉGAGEMENT MINIMAL, UTILISANT BUSTIBLE - 18 POUCES / 455 mm. CE DÉGAGEMENT PEUT ÊTRE RÉDUIT EN UTILISANT DES PROTECTEURS DE TUYAUX CLAS-
RIALS-18INCHES/455MM. CLEARANCE MAY BE REDUCED BY THE USE OF LISTED PIPE SHIELDS, E. BACKWALL TO CONNECTOR/ UN RACCORD DE MUR DOUBLE
MUR DE FOND / RACCORD SÉS, PROTECTEURS DE MUR OU AUTRES MOYENS APPROUVÉS PAR LES OFFICIELS DE LA CONSTRUCTION OU DU SERVICE
WALL PROTECTORS OR OTHER MEANS APPROVED BY LOCAL BUILDING OR FIRE OFFICIALS. A. 8 IN. / 203 MM D’INCENDIE DE VOTRE RÉGION.
F. CORNER TO CONNECTOR/
• COMPONENTS REQUIRED FOR MOBILE HOME AND ALCOVE INSTALLATION: OUTSIDE AIR KIT. COIN / RACCORD B. 5 IN. / 127 MM CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES
BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE LISTED TO: C. 3 IN. / 76 MM • PIÈCES REQUISES POUR INSTALLATION EN MAISON MOBILE OU EN ALCÔVE: PRISE D’AIR EXTÉRIEUR
IN CANADA - ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY MUR ARRIERE ET L’UN DES RACCORDS SUIVANTS: EN COMBINAISON AVEC L’UN DES SYSTÈMES DE CHEMINÉE COM-
BACK WALL D. 15.5 IN. / 394 MM
IN USA - UL-103 HT LISTED CONNECTOR AND CHIMNEY PATIBLES SUIVANTS:
• USE COMPONENTS SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS.
E. 8.25 IN. / 210 MM
F. 11 IN. / 279 MM CANADA-TUYAU DE RACCORDEMENT HOMOLOGUÉ ULC S-641 ET CHEMINÉE HOMOLOGUÉE ULC S-629.
• OPTIONAL COMPONENT - BLOWER(TRNO.19BLOWA), FAN ELECTRICAL RATING: 115V, 60HZ, .5 AMP. ÉTATS-UNIS - TUYAU DE RACCORDEMENT ET CHEMINÉE HOMOLOGUÉS UL-103HT.
B

TN 20B
• CAUTION: RISK OF EXCESSIVE TEMPERATURES - KEEP ASH DUMP CLOSED DURING FIRING OF THE E MOBILE
* ALCOVE INSTALLATION HOME INSTALLATION • COMPOSANTS OPTIONNELS: VENTILATEUR (WODC.BLOW), ALIMENTATION ÉLECTRIQUE DU VENTILATEUR : 115 V, 60 HZ, 0.5
HEATER. • DO NOT ROUTE POWER CORD BENEATH HEATER. A USING DOUBLE WALL USING DOUBLE WALL AMP. LE CORDON D’ALIMENTATION ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÊLE.
• OPERATE ONLY WITH FEED DOOR CLOSED. OPEN TO FEED FIRE ONLY. CONNECTOR/* INSTALLATION CONNECTOR/ INSTALLATION
EN ALCÔVE UTILISANT UN EN MAISON MOBILE UTILISANT LE FIL ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÊLE
• KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIALS WELL AWAY FROM HEATER. RACCORD DE MUR DOUBLE UN RACCORD DE MUR DOUBLE
The Rating label is located on the lower portion of the rear cover.

• ATTENTION: RISQUE DE TEMPÉRATURES EXCESSIVES - GARDES LE TIROIR DE CENDRES FERMÉ PENDANT L’ALLUMAGE DU
• REPLACE GLASS ONLY WITH CERAMIC GLASS. POÈLE.
A. 8 IN. / 203 MM 8 IN. / 203 MM

SIDE WALL
MUR COTE
HORIZONTAL CONNECTOR NOT PERMITTED IN MOBILE HOMES B. 5 IN. / 127 MM 5 IN. / 127 MM • OPÉREZ SEULEMENT LORSQUE LA PORTE D’ALIMENTATION EST FERMÉE. • OUVREZ SEULEMENT POUR ALIMENTER LE FEU.
 AS TESTED - PIPE SHIELD MAY BE REQUIRED BY LOCAL AUTHORITIES. D
C. N/A 3 IN. / 76 MM • GARDEZ LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES BIEN ÉLOIGNÉS DU POÊLE.
* ALCOVE SIZE : DEPTH - 3 FT. / .91 M MAX., HEIGHT 7 FT. / 2.1 M MIN., WIDTH 38 IN. / .97 M MIN. D. 15.5 IN. / 394 MM 15.5 IN. / 394 MM • REMPLACES LA VITRE AVEC UNIQUEMENT DE LA VITRE CÉRAMIQUE.
COMBUSTIBLE FLOOR MUST BE PROTECTED BY A CONTINUOUS NON-COMBUSTIBLE MATERIAL E. 8.25 IN. / 210 MM 8.25 IN. / 210 MM CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES
EXTENDED TO THE FRONT, SIDES AND BACK AS INDICATED. F. N/A 11 IN. / 279 MM  TEL QUE TESTÉ: UN ISOLANT THERMIQUE POUR TUYAU PEUT ÊTRE EXIGÉ PAR LES AUTORITÉS LOCALES. * DIMENSIONS
• FOR USE WITH SOLID WOOD FUEL ONLY. STOVE DESIGNED TO BURN CORDWOOD ONLY. BURNING IN CANADA G. 18 INCHES / 457 MM D’ALCÔVE EN MATÉRIAUX COMBUSTIBLES: PROFONDEUR MAX.: 3 PIEDS (0,91 M), HAUTEUR MIN.: 7 PIEDS (2,1 M), LARGEUR
Rating Label

OTHER MATERIALS MAY CAUSE DAMAGE TO STOVE OR HOME. AU CANADA H. 8 INCHES / 200 MM MIN.: 43 PO (1,09 M).
• THIS WOOD HEATER NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. - CON- MUR ADJACENT I. 8 INCHES / 200 MM LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR UN MATÉRIEL NON-COMBUSTIBLE TOUT D’UNE PIÈCE QUI DOIT
SULT THE OWNER’S MANUAL FOR FURTHER INFORMATION. ADJACENT WALL S’ÉTENDRE DE PAR LE DEVANT, LES COTÉS ET L’ARRIÈRE TEL QU’INDIQUÉ.
• IT IS AGAINST FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCON- IN U.S.A. G. 16 INCHES / 405 MM · POUR UTILISATION AVEC BOIS SOLIDE SEULEMENT. LE POELE CONÇU POUR BRÛLER BOIS DE CORDE
H. 3.5 INCHES / 89 MM SEULEMENT. LA COMBUSTION D’AUTRES MATÉRIELS PEUT.
SISTANT WITH THE OPERATING INSTRUCTIONS IN THE OWNER’S MANUAL C I. 0 INCHES / 0 MM
CET APPRAREIL DE CHAUFFAGE AU BOIS DOIT FAIRE L’OBJETD’ENTRETIENS ET D’INSPECTIONS PÉRIODIQUES POUR
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING DOS UN FONCTIONNEMENT ADÉQUAT. CONSULTEZ LE MANUEL D’UTILISATION POUR PLUS D’INFORMATION.
AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE BACK I
(Type 1 floor MANUFACTURED BY/ FABRIQUÉ PAR:
F PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
AND INSTRUCTIONS.// CHAUD LORSQU’EN OPÉRATION. NE PAS TOUCHER, TENEZ LES H H protector - ap- 2975 ALLENBY RD., DUNCAN, BC V9L 6V8
proved to UL1618)
ENFANTS ET LES VÊTEMENTS BIEN À L’ÉCART. LE CONTACT PEUT CAUSER DES BRÛLURES HEATER
Minimum 20GA
SIDE
SIDE

COTE
CAUTION

MUR ADJACENT
COTE

POELE

ADJACENT WALL
À LA PEAU. CONSULTEZ LA PLAQUE CE CONSTRUCTEUR ET LES INSTRUCTIONS. steel
G
U.S. ENVIRONMENTAL PROTECTION AGENCY.
FRONT
Certified to comply with 2020 crib wood particulate emission standards, DEVANT DATE OF MANUFACTURE/ DATE DE MANUFACTURE
using test Method 28R // Certifié conforme aux normes sur les émissions de 1.6 g/hr J F M A M J J A S O N D
particules de 2020.
MADE IN CANADA/ FABRIQUÉ AU CANADA 2018 2019 2020 2021 2022
040118 500000055 TN20-B-1

110618-28
110618-28 TN 20B ©PACIFIC ENERGY FIREPLACE 27
PRODUCTS LTD.
© 2018 Copyright Pacific Energy Fireplace Products LTD

Reproduction, adaptation, or translation

without prior written permission is prohibited,
except as allowed under the copyright laws.

For technical support, please contact your retailer

Web site: www. truenorthstoves.com

2975 Allenby Rd., Duncan, BC V9l 6V8

28 ©PACIFIC ENERGY FIREPLACE TN 20B 110618-28

PRODUCTS LTD.