Information Sheet 8

Information Sheet 5.
2-8
Perimeter Lighting
Learning Objectives:
After reading this INFORMATION SHEET, YOU MUST be able to:
 Define perimeter lighting;
 Differentiate the four types of lighting;
 Understand on how CAST LED Perimeter Lighting System applied.
Introduction
Perimeter security lighting is an important part of an outdoor perimeter security
intrusion detection system. Illuminating the camera field of view with an Infrared (IR) or
white-lighting system significantly improves the performance of the camera. Ensuring
optimum illumination for any perimeter application is crucial for achieving top level security
and safety at night. More and more perimeter applications are turning to Infra-Red and
White-Light LED lighting solutions instead of traditional lighting technologies such as
halogen, sodium or metal halide.
_______________________________________________________________
Typical Perimeter Lighting Projects
Every perimeter lighting application is unique. Whether you are lighting the perimeter
of a power station, a prison, or an airport, there are general standards and recommended
practices for using the correct lighting solution and the best design approach for sites with
typical characteristics.
Most perimeter fence line applications have a “sterile zone” on the inner side of the
fence varying from 2m to 5m in width (Figure 1). This is the main area of concern for
illuminating and monitoring.
Most perimeter projects illuminate the sterile zone up to the inside of the fence line.
Some installations will illuminate to a distance beyond the fence line into the “attack zone”.
The attack zone is the external public area from which an intruder would approach.
Figure 5.2.1
Sterile Zone
2-5m(6-16ft)
Inner Area
Attack Zone
Lighting
Columns
Column Placement
Column Placement Columns are typically placed at a minimum distance of 2.5m
(8ft) from the fence line in order to prevent intruders from using them to climb the fence
structure. Columns are mostly placed outside of the sterile zone. • Typical column spacing for
CCTV lighting is usually 50m (164ft). • Between 25m (82ft) and 30m (98ft) for general
lighting.
Perimeter Lighting Design for Dome Cameras

Pan-Tilt-Zoom (PTZ) domes typically utilize lights either side of camera to deliver
full 360° coverage, illuminating distances up to100m (328ft). Typical products used for 360°
dome lighting would be wide angle illuminators. Sometimes it may be necessary to use a
small illuminator looking down a column if it is a little dark and exposed due to perimeter
layout and lighting pattern.
Combined Infra-Red and White-Light
The benefit of White-Light LED illumination is that it is quick to start. It can be
activated instantly on demand. For this reason, Infra-Red illumination is often used in
conjunction with White-Light illumination. IR can be used continuously to covertly monitor a
scene, and WL only activated when needed (e.g. general lighting for a patrol or deterrent
lighting to warn off an intruder). External triggers such as a PIR detector, motion detection
software in camera or fiber optic fence line cable for example, can trigger the White-Light
illuminators via a telemetry input, to turn them on instantly for defined period of time. This
provides a more energy and cost efficient solution, reduces visible light pollution, as well as
providing a more dynamic response. For example, IR could illuminate the attack zone, and
when an intruder is detected by a PIR detector, or when they touch the fence line which is
secured with fiber optic cable, these devices would trigger the White-Light illumination to
turn on. Lighting can be triggered individually or in batches (all connected in series/parallel
via telemetry). This is not possible with technologies such as metal halide and sodium
lighting, due to their slow warm up.
Figure 5.2.2
General Area Lighting

Recommended levels of visible White - light illumination for general area purposes = 5lux
(BSEN standards)
Figure 5.2.3
Figure 7: Perimeter general area lighting design example showing 1 light and camera per column. lights
mounted at 8m (26ft), cameras mounted at 6m (19ft), 30m (98ft) column spacing.
Lighting Level Notes

 Lighting level requirements may be different in attack zone or inner site area.
 Columns for general lighting in a perimeter application are usually 8m (26ft) high.
 Generally, White-Light illuminators and cameras are kept separate when concerned
with general area illumination. The lighting is usually positioned at the top of the
column at 8m (26ft), and the cameras positioned further down around 6m (19ft).
Mounting the cameras lower down reduces glare directly into the camera lens.
 Typical column spacing is between 25m (82ft) and 30m (98ft).
 The lighting always illuminates the horizontal plane e.g. so that it would illuminate
down onto the ground to create a well lit area for site personnel, targeted down to
illuminate beyond the base of the next column.
 Lighting is usually positioned to point along the fence line, rather than directly at the
fence line. However, directly illuminating the fence on a vertical plane is possible;
project dependent.
Typical White-Light Solution

The main LED lighting product which we use to design into perimeter lighting
projects is the White-Light 200 series illuminator with a 10 degree beam angle, due to its
lumen output and distance capability.
Figure 5.2.4
25m (82ft) column spacing – x1 RL200-AI-10 per column
A 25m (82ft) to 30m (98ft) column spacing is most typical for a high security general lighting
perimeter application. FSI’s recommended practice for illuminating a perimeter with a 25m (82ft) or
30m (98ft) column spacing is to position the lighting on the side of the column, pointed down to
illuminate beyond the base of the next column.
The angle of elevation of the illumination is such that it doesn’t put glare into the camera on
the adjacent column. All cameras must face the same way as the lighting.
Figure 5.2.5
35m (115ft) column spacing – x2 RL200-AI-10 per column
Recommended practice for illuminating a perimeter with a 35m (115ft) column

spacing is to utilize two lighting units, one each side of the column, to achieve a greater
distance whilst still achieving even coverage and the minimum lux levels.
The lighting should be pointed down so that the beam patterns cross paths at a center
point with the illumination from the adjacent column. There is more risk of the lighting in
this design putting glare into the camera lens, but ensuring that the angle of elevation isn’t
tilted up too high will avoid any direct overexposure.
Figure 5.2.6
40m column spacing – x2 RL200-AI-10 and x2 RL100-50 per column
The best technique for illuminating a perimeter with 40m (131ft) column spacing is
similar to the technique for a perimeter with 35m (115ft) column spacing. Perimeters with
both 35m (115ft) and 40m (131ft) column spacing utilize lighting units on either side of the
column with the illumination pointing towards the adjacent column. However the beam
patterns on a 40m (131ft) column spacing design do not cross.
The elevation needs a higher tilt on the 40m (131ft) spaced design in an attempt to
project the beam pattern out further to achieve more distance. The beams do not cross, but
they hit the ground and merge at a point which still ensures the minimum lux level. However
with the illumination target at quite some distance from the column, this leaves the base of
the column dark and exposed. Therefore, a small lower powered light fitting pointing directly
downwards on each side of the column is needed to ensure the minimum lighting levels are
achieved at all areas across the sterile zone.
45-50m column spacing

The same technique is used for perimeters with a 45 (148ft) and 50m (164) column
spacing; however the illumination levels tend to drop towards the absolute minimum
requirement. Beyond 50m (164) is not recommended column spacing for achieving good
illumination levels for general area illumination at night. At this distance, the cameras on the
columns would also be affected too. The targeting angle of illumination would be too
shallow, and would cause glare into the camera lens and impair the image.
Figure 5.2.7
Illuminating the Fence
White-Light illumination can also be targeted directly at the fence line should the
project require it to. Higher lighting levels can be achieved using this lighting design
approach, due to the light travelling a shorter distance and hitting the fence on a vertical
plane, rather than the ground on a horizontal plane.
There are actually four types of lighting, each used for specific purposes.
1. Continuous lighting - is the most common type of lighting. It consists of a
series of fixed lights arranged to flood a given area continuously during
darkness with overlapping cones of light.
2. Standby lighting - consists of luminaires that are not continuously lit but are
either automatically or manually turned on when suspicious activity is detected
or suspected by the security force or alarm systems.
3. Emergency lighting - can be powered by installed or portable generator or
battery and is used for power failure or other situations that render the normal
system inoperative.
4. Portable lighting - consists of manually operated, movable searchlights that
may be lit during hours of darkness or only as needed.
The CAST LED Perimeter Lighting System addresses a need that other lighting
systems do not - an inexpensive, energy-efficient way to enhance visual security for
extensive or remote property boundaries. It also fills the need for a portable lighting
system for the military, temporary fence companies, event providers, and consumers.
Commercial and Municipal Properties

Currently, commercial and municipal property perimeters are illuminated by
general area lighting or security lighting - usually by high-pole-mounted or bracket-
mounted luminaires. This approach works fairly well when perimeter fences are
within areas adjacent to buildings or illuminated parking lots.
It is, however, often the case that property perimeters extend beyond areas that
require general area illumination. In such cases, perimeters are typically left unlit, or
they require long expensively-installed 120-volt lines and the use of floodlighting that
is neither energy-efficient nor efficacious.
The CAST LED Perimeter Lighting System provides a highly energy-efficient
and inexpensive way to illuminate these long fenced perimeters – applying
illumination sufficient for security cameras and guards to detect the presence of
intruders.
Cost savings realized on several fronts

 Design - one luminaries mounted on every 2nd or 3rd fence post - no need for
extensive lighting plans.
 Installation - because 24-volt systems comply with less-restrictive low-voltage
lighting codes, the run from the transformer to the fence can be buried to a
shallow depth of 6 inches (instead of 18 inches for 120 volts) and can be
directly buried without conduit. Along the fence, the wire can be run through
above-ground pvc or metal conduit attached to fence (no trenching). Low-
voltage current presents zero risk for electrical shock injury.
 Operation - because highly efficient LED illumination is focused only where
it’s needed (along the perimeter), energy costs are greatly reduced compared to
general area lighting.
 Maintenance - using Cree XPE LED’s (L70 36,300 hours), expected life
exceeds 10 years. The LED driver also has extended life features (including
surge and spike protection) to ensure continuous operation throughout the life
of the LED. During this period, the only maintenance required would be
occasional cleaning of the hardened - glass LED enclosure.
Special Commercial and Municipal Applications

 Airports - system illuminates long perimeter fences, enhancing security and
aeronautical safety.
 Energy Providers (Power plants and Substations) - system provides security
for long perimeter fences in remote locations.
 Public Parks, Residential Areas, and Observatories - provides dark-sky
compliant perimeter and path lighting in LZ-0 zones.

Information Sheet 8

Uploaded by

Copyright:

Available Formats

Information Sheet 8

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Information Sheet 8

Uploaded by

Copyright:

Available Formats

Information Sheet 5.

Perimeter Lighting Design for Dome Cameras

General Area Lighting

Lighting Level Notes

Typical White-Light Solution

Recommended practice for illuminating a perimeter with a 35m (115ft) column

45-50m column spacing

Commercial and Municipal Properties

Cost savings realized on several fronts

Special Commercial and Municipal Applications

You might also like