Seashield Marine Systems: Seashield 550 Epoxy Grout (Australian)

SeaShield Marine Systems
SeaShield™ 550 Epoxy Mixing Ratios

For (5:1 C:A/B Weight Mixing Ratio - Hand Placing or
Pumping for Aggregate
Grout (Australian)
Aggregate Solid to A - Volume B - Volume Yield
Bag Weight Liquid Ratio (L) (L) (m3)
15 kg 5.0 1.8 1.0 0.009
These mix designs are given as a guide. Site temperature,

Encapsulation and Repair Grout material temperature, placing thickness may cause these to
for Concrete, Timber and Steel be amended. A trial mix should always be checked before
proceeding.
SeaShield 550 is a 3-component water
™ NOTE: Component "C" (Aggregate) is a silica sand with a
proprietary formula of fine and course grades. When fully cured,
displacing epoxy resin aggregate formulation the epoxy resin is chemically bonded to the silica surface.
which provides a durable, well bonded repair This provides higher physical properties such as compressive
to concrete, timber and steel below water. tensile and impact strength.
Cure Schedule
Uses
Pot Life 200 g. @ 25° C 100 to 120 minutes
SeaShield™ 550 Epoxy Grout is designed for underwater
application. Because of its relatively long pot life, it is easy to Pot Life 200 g. @ 38° C 35 to 45 minutes
handle yet still provides high early strength. *Tack-free 16° C to 26° C 10 to 20 hours
time
It can either be placed by pouring into forms or pumped into
place and is typically used for rebuilding piers, jetties and *Tack-free 4°C to 15° C 20 to 40 hours
barrier walls. It is also very effective for chemical anchoring time
of bolts and anchors in rails, equipment bases and other Full cure 16° C to 26° C 30 to 60 hours
structural applications. Full cure 4°C to 15° C +120 hours
Cure time is considerably longer at colder temperatures.
Compliant to AS/NZS 4020:2005 for contact with potable water, When mixed in 19 L pails, pot life could be shorter due to
up to an exposure rate of 5,100 mm2/L at 20oC. volume of material.
*Based on 50 mm cubes.
Physical Properties
(unmixed) @ 25°C Recommended Temperatures
Component “A” (resin): Application: ≥0oC, preferable 15oC to 30oC
Specific Gravity 1.13 Service: -10oC to 65oC
Viscosity 700 cP Peak Intermittent Temperature: 75oC
Colour Clear
Ratio by Weight 66%
Moisture Sensitivity
Component “B” (hardener):
SeaShield™ 550 Epoxy Grout has good wet adhesion and
Specific Gravity 0.96
good water displacement capabilities.
Viscosity 400 cP
Colour Amber
Ratio by Weight 33%

Component “C” (aggregate):
Free Flowing Non-Dusting Powder
Colour Neutral
Physical Properties of Cured System Application
(7 day cure @ 22°C) w/ 5:1 mix ratio) Placing by Hand Pouring into Forms
Compressive Strength ASTM C579 72 MPa Once mixed, pour into formwork, ensuring it is well compacted,
Tensile Strength ASTM C307 15 MPa vibrating where possible. When using wood forms, use paraffin
Bond / Shear Strength ASTM C882 13.7 MPa wax or polyethylene sheet to ensure easy formwork removal
Shrinkage ASTM C531 0.07% Max. after pouring.
Water Absorption ASTM C413 0.45% Max.
Placing by Pumping
All three components shall be mixed thoroughly and shall be
Surface Preparation pumped through a minimum 32 mm hose ID with a suitable pump
such as a peristaltic or rotor stator pump.
Surface preparation is very important and will improve the
adhesion and extend the life of the grout: A bottom plug of 150 - 300 mm of epoxy grout shall first be pumped
into the lowest injection port. The epoxy grout shall be allowed to
a) Must be cleaned free of old existing coatings. New concrete cure before proceeding with subsequent lifts.
should hydrate a minimum of 5 days prior to placement of
grout. Once epoxy grout is cured the grout injection shall begin at the
bottom injection port and proceed upwards. As the jacket is filled
b) Remove all oils, greases, dirt and wax solutions from to each port, the lower port shall be capped off and repeated until
surface. the top of the jacket is reached. The injection process shall be
continuous except when the injection hose is moved from port
c) High-pressure waterblast, sandblast or shot blast surface
to port.
to remove contaminants which will interfere with proper
adhesion. Water blast shall be done at a minimum of
24 MPa. Clean Up
Pumping equipment is best cleaned with SeaShield™ Equipment
Cleaner or Simple Green Concentrate Cleaner. Recirculating
Mixing using a sponge "pig" is always recommended and an efficient
Pour component "A" resin & component "B" hardener into a cleaning procedure.
19 L pail. Agitate with a low speed mixer (200-300 rpm) for at
least 3 minutes. When mixing, occasionally scrape the sides & Storage
bottom to make sure the entire product is mixed consistently.
Slowly add the aggregate when mixing. The product is mixed Store all 3 components in a dry, well-ventilated area at temperatures
properly when an even color is achieved without streaks and between 4.4°C and 40.5°C. Shelf life of unopened components
all the aggregate has been mixed with the resin. is 2 years.
It is recommended that SeaShield™ 550 Part A, B & C should
Yield be stored at 20°C to 30°C for 24 hours prior to use for optimum
5:1 : 3.8 L of 550 A & B with 15 kg of Aggregate yields = 0.009 m3 pumping and productivity.
Packaging
Equipment (C:A/B, 5:1 Weight Ratio)
The epoxy grout shall be pre-mixed and pumped through a SeaShield™ 550 - Part A (2 kg) & B (1 kg)
peristaltic pump or rotor stator pump. The equipment shall
Aggregate (Part C) - 15 kg per bag
be capable of delivering mixed grout through hoses into the
jackets at a rate 3.8 L per minute or greater. Contact pump
equipment manufacture to make sure pump is capable of
pumping epoxy grout.
Prior to using the pump, all hose lines shall be primed by

circulating minimum 3.8 L of the SeaShield™ Hose Lubricant.
The maximum hose length should be no longer than 15 m.
The minimum hose diameter should be 32 mm ID.
INHERENT RISK: Purchaser assumes all risk associated with

the use or application of the product, including any possible
damage to equipment during pumping.
VER 1803.07

Seashield Marine Systems: Seashield 550 Epoxy Grout (Australian)

Uploaded by

Copyright:

Available Formats

Seashield Marine Systems: Seashield 550 Epoxy Grout (Australian)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Seashield Marine Systems: Seashield 550 Epoxy Grout (Australian)

Uploaded by

Copyright:

Available Formats

SeaShield Marine Systems

SeaShield™ 550 Epoxy Mixing Ratios

These mix designs are given as a guide. Site temperature,

Prior to using the pump, all hose lines shall be primed by

INHERENT RISK: Purchaser assumes all risk associated with

You might also like