System MQ: Medium Duty Channel Installation Stainless Steel

System MQ
System ML channel installation

Medium Duty
Channel Installation
Stainless Steel
page
page 119
119
March 2006 page 119
System MQ Channel Installation
Stainless Steel
Hilti. Outperform. Outlast.
System MQ - Stainless Steel
Description page
Technical Data - Channel selection 122
Channel selection diagram (stainless steel) 123
Technical data for brackets (stainless steel) 124
Installation channels 125
Cantiliver brackets 126
Channel nut 127
Pipe ring saddle 128
Angles, angle brackets connectors 129-130
MQP-U-R universal joint 131
Beam clamps 132-133
Accessories 134
3D system 135
MP-SRNI / MP-SRN pipe rings 136-137
MP-MRI /MP-MR pipe rings 138-139
MP-MRXI pipe rings 140
Stainless steel accessories for pipe rings 141
Installation accessories 142
page 121
Technical data Channel sections (stainless steel)
2.5
2
82.6
Definition of axes 2
52
2
41.2
41.3
F F
20.6
e2 e1 41.3 41.3
41.3 41.3 41.3
y-axis
e1 e2
"open" z-axis
MQ-21-RA2 MQ-21-R MQ-41-RA2 MQ-41-R MQ-52-R MQ-21D-RA2 MQ-21D-R MQ-41D-R
Channel wall thickness t [mm] 2.0 2.0 2.0 2.0 2.5 2.0 2.0 2.0
Cross-sectional area A [mm2] 165.3 165.3 245.1 245.1 352.1 330.6 330.6 490.3
Channel weight [kg/m] 1.45 1.47 2.09 2.12 3.00 2.92 2.96 4.27
Delivered length [m] 3/6 3/6 3/6 3/6 3/6 3/6 3/6 3/6
Material
Permissible stress σperm. [N/mm2] 142.9 155.8 142.9 155.8 155.8 142.9 155.8 155.8
Stainless steel A2 (1.4301) ● ● ●
Stainless steel A5 (1.4571) ● ● ● ● ●
Cross-section values
Y-axis
Axis of gravity "open" 1) e1 [mm] 10.84 10.84 21.13 21.13 26.67 20.60 20.60 41.30
Axis of gravity e2 [mm] 9.76 9.76 20.17 20.17 25.33 20.60 20.60 41.30
Moment of inertia Iy [cm4] 0.92 0.92 5.37 5.37 11.41 4.98 4.98 30.69
Section modulus "open" Wy1 [cm3] 0.85 0.85 2.54 2.54 4.28 2.42 2.42 7.43
Section modulus Wy2 [cm3] 0.94 0.94 2.66 2.66 4.50 2.42 2.42 7.43
Radius of gyration iy [cm] 0.74 0.74 1.48 1.48 1.80 1.23 1.23 2.50
Permissible moment 2) My [Nm] 121 132 363 396 666 346 377 1158
Z-axis
Moment of inertia Iz [cm4] 4.39 4.39 7.33 7.33 10.79 8.78 8.78 14.67
Section modulus Wz [cm3] 2.13 2.13 3.55 3.55 5.23 4.25 4.25 7.10
Radius of gyration iz [cm] 1.63 1.63 1.73 1.73 1.75 1.63 1.63 1.73
Selection of channel section:
● The given data is based on a single span (simply-supported beam) bearing a single load, F (kN), at mid-span, L/2.
● If several loads are acting on a single span (simply-supported beam), these may be summated and regarded as a single load acting at mid span. By taking this
approach, the design calculation is on the safe side. (➔ Cross section selection table).
● The permissible stress in the steel and the max. deflection, L/200, are not exceeded with the given max. span width, L (cm).
● The channel's own weight was taken into account.
Max. span width, L (cm) / deflection, f (mm) 3)
L f L f L f L f L f L f L f L f
F (kN) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm)
0.25 120 6.0 120 6.0 277 13.8 277 13.8 380 19.0 261 13.1 261 13.1 560 28.0
0.50 86 4.3 86 4.3 204 10.2 204 10.2 290 14.5 195 9.7 195 9.7 449 22.5
0.75 64 2.7 70 3.4 168 8.4 168 8.4 242 12.1 161 8.1 161 8.1 383 19.2
1.00 48 1.5 52 1.9 143 6.8 147 7.3 212 10.6 135 6.3 141 7.0 339 16.9
1.25 39 <1 42 1.2 115 4.4 125 5.7 190 9.5 109 4.1 119 5.3 307 15.3
1.50 32 <1 35 <1 96 3.1 105 4.0 174 8.7 91 2.9 99 3.7 282 14.1
1.75 27 <1 30 <1 83 2.3 90 3.0 150 6.5 78 2.1 85 2.7 257 12.3
2.00 24 <1 26 <1 72 1.8 79 2.3 132 5.0 69 1.6 75 2.1 226 9.6
2.25 21 <1 23 <1 64 1.4 70 1.8 118 4.0 61 1.3 67 1.7 202 7.7
2.50 19 <1 21 <1 58 1.1 63 1.5 106 3.3 55 1.1 60 1.4 182 6.3
2.75 17 <1 19 <1 53 <1 57 1.2 96 2.7 50 <1 55 1.1 166 5.3
3.00 16 <1 17 <1 48 <1 53 1.0 88 2.3 46 <1 50 <1 153 4.4
3.50 14 <1 15 <1 41 <1 45 <1 76 1.7 39 <1 43 <1 131 3.3
4.00 12 <1 13 <1 36 <1 39 <1 66 1.3 34 <1 38 <1 115 2.5
4.50 10 <1 11 <1 32 <1 35 <1 59 1.0 31 <1 33 <1 102 2.0
5.00 9 <1 10 <1 29 <1 32 <1 53 <1 27 <1 30 <1 92 1.6
6.00 8 <1 8 <1 24 <1 26 <1 44 <1 23 <1 25 <1 77 1.1
7.00 6 <1 7 <1 21 <1 22 <1 38 <1 19 <1 21 <1 66 <1
8.00 5 <1 6 <1 18 <1 20 <1 33 <1 17 <1 19 <1 58 <1
Selection example: Single load
≈
● 1.0 kN ( 100 kg) should be carried by a channel with a channel span
width L = 100 cm (single span simply supported).
Conversion
1 kp
kp
–
kg
1
N
10
kN
0.01
F[kN]
Solution: 1 kg 1 – 10 0.01 L/2 L/2

● Select the line showing the load, F = 1.0 kN. 1N 0.1 0.1 – 0.001 L[cm]
● The MQ-41-RA2 to MQ-41D-R channels can be used because the
permissible span width (tabulated value) is larger or equal 1 kN 100 100 1000 – F
to the required span, L = 100 cm.

1)
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
f[mm]
2)
Perm. My = σperm.· min. (Wy1, Wy2)
3)
The channel length is max. 6.0 m. Contact Hilti technical staff about channels longer than 6.0 m!
page 122
Load, F (kN)
Channel selection diagram 25.00
(stainless steel) Single span (simply supported)

with single load at mid span, L/2
20.00
All values were calculated for a permissible stress of
σperm. (see technical data for channel selection) and a
deflection of L/200.
15.00
MQ-52-R
10.00
F[kN]
MQ-41-R
5.00
L/2 L/2 MQ-41-RA2
MQ21-R
L[cm] MQ-21-RA2
0.00
0 25 50 100 150 200 250 300
Span width (cm)
Load, F (kN)
30.00
25.00
20.00
MQ-41D-R
15.00
10.00
MQ-21D-R
5.00
MQ-21D-RA2
0.00
0 25 100 200 300 400 500 600
Span width (cm)
Channel selection table (stainless steel)

Single span (simply supported)
with single load at mid span, L/2
2.5
F[kN] 2
2
82.6
2
52
41.2
2
41.3
L/2 L/2
20.6
L[cm] 41.3 41.3 41.3 41.3 41.3
Max. load, F (kN) / deflection, f (mm)

MQ-21-RA2 MQ-21-R MQ-41-RA2 MQ-41-R MQ-52-R MQ-21D-RA2 MQ-21D-R MQ-41D-R
Span width F (kN) f (mm) F (kN) f (mm) F (kN) f (mm) F (kN) f (mm) F (kN) f (mm) F (kN) f (mm) F (kN) f (mm) F (kN) f (mm)
L (cm) max. L/200 max. L/200 max. L/200 max. L/200 max. L/200 max. L/200 max. L/200 max. L/200
25 1.92 <1 2.10 <1 5.77 <1 6.29 <1 10.59 <1 5.48 <1 5.98 <1 18.36 <1
50 0.96 1.6 1.05 1.8 2.90 <1 3.16 <1 5.32 <1 2.75 <1 3.00 <1 9.23 <1
75 0.64 3.6 0.66 3.8 1.93 1.9 2.10 2.0 3.54 1.6 1.83 1.9 2.00 2.1 6.15 1.0
100 0.37 5.0 0.37 5.0 1.44 3.3 1.57 3.6 2.65 2.9 1.37 3.4 1.49 3.7 4.61 1.9
125 0.23 6.3 0.23 6.3 1.15 5.2 1.25 5.7 2.11 4.5 1.09 5.3 1.19 5.8 3.68 2.9
150 0.15 7.5 0.15 7.5 0.95 7.5 0.95 7.5 1.75 6.5 0.88 7.5 0.88 7.5 3.06 4.2
175 0.11 8.8 0.11 8.8 0.69 8.8 0.69 8.8 1.49 8.8 0.63 8.8 0.63 8.8 2.61 5.7
200 0.08 10.0 0.08 10.0 0.52 10.0 0.52 10.0 1.13 10.0 0.47 10.0 0.47 10.0 2.27 7.4
225 0.05 11.3 0.05 11.3 0.40 11.3 0.40 11.3 0.88 11.3 0.36 11.3 0.36 11.3 2.01 9.4
275 0.02 13.8 0.02 13.8 0.25 13.8 0.25 13.8 0.56 13.8 0.22 13.8 0.22 13.8 1.58 13.8
300 0.01 15.0 0.01 15.0 0.20 15.0 0.20 15.0 0.46 15.0 0.17 15.0 0.17 15.0 1.31 15.0
page 123
Technical data for brackets (stainless steel A5)

Type of load 1: uniform Type of load 2: single Type of load 3 Type of load 4 Type of load 5
F1 F1 F2 F2 F3 F3 F3
F1 = q · i 1/2 1/
2 1/
3 1/
3
1/
3
1/ 1/ 1/ 1/
4 4 4 4
F1 [N] F1 [N] F1 [N] F2 [N] F3 [N]

Channel
Bracket L (mm) HVZ-R M12 1)
HST-R M12 2)
HVZ-R M12 1)
HST-R M12 2)
HVZ-R M12 1)
HST-R M12 2)
HVZ-R M12 1)
HST-R M12 2)
HVZ-R M121) HST-R M122)
MQK-21/300-R 300 870 870 870 870 340 340 430 430 290 290
MQK-21/450-R 450 400 400 570 570 150 150 250 250 150 150
MQK-41/300-R 300 2620 2620 2620 2620 1310 1310 1310 1310 870 870
MQK-41/450-R 450 1740 1740 1740 1740 870 870 870 870 580 580
MQK-41/600-R 600 1300 1300 1300 1300 500 500 650 650 430 430
MQK-21 D/450-R 450 1650 1650 1650 1650 830 830 820 820 550 550
MQK-41 D/750-R 750 3050 1890 3050 1890 1520 940 1520 940 1010 630
1)
Loading capacity of the bracket (steel loading capacity) or with HVZ-R M12 fastening, the loading capacity of the bracket is reached with the HVZ-R M12.
2)
Loading capacity of the bracket with HST-R fastening, alternatively, loading values with HIT-RTZ M12 are at least those with HST-R M12.
≈
Load values are for grade C20/25 concrete ( B25).
Alternatively, fastening in solid or hollow brick with HIT HY 50 and approval is possible. Use stainless-steel anchor rods (loading values not given in this table).
The bracket’s own weight has been allowed for.
The loads apply only if the bracket is fastened away from a building component edge (fastenings made at component edges must be designed separately).
Separate verification must be provided that forces are transferred to the respective base material, i.e. steel and concrete.
The application guidelines in anchor approvals must be observed. Loading values according to approval status July 2005.
The deflection (deformation) of L/150 was observed in all cases, this being measured at the point of load application.
HVZ-R adhesive anchor HST-R stud anchor

EDELSTAHL ® EDELSTAHL ®
Rost Rost
frei frei
Technical data for brackets with angle brace (stainless steel A5)
Type of load 1: uniform Type of load 2: single Type of load 3 Type of load 4 Type of load 5
F1 F1 F2 F2 F3 F3 F3
F1 = q · I 1/2 1/2 1/3 1/3 1/3 1/4 1/4 1/4 1/4
Bracket L (mm) Brace F1 [N] 1) F1 [N] 1) F1 [N] 1) F2 [N] 1) F3 [N] 1)

MQK-21/450-R 450 short 4520 1170 420 2020 1780
MQK-41/450-R 450 short 5360 3520 2440 2680 1780
MQK-41/600-R 600 long 4060 2630 2030 2030 1350
MQK-21 D/450-R 450 short 5360 3350 2320 2680 1780
MQK-41 D/750-R 750 long 3220 3220 1610 1610 1070
1)
Loading capacity of the bracket (steel loading capacity) or the loading capacity of the bracket is reached with the HVZ-R, HIT-RTZ or HST-R M12 fastening.
≈
Load values are for grade C20/25 concrete ( B25).
Alternatively, fastening in solid or hollow brick with HIT HY 50 and approval is possible. Use stainless-steel anchor rods (loading values not given in this table).
The bracket’s own weight has been allowed for.
The loads apply only if the bracket is fastened away from a building component edge (fastenings made at component edges must be designed separately).
Separate verification must be provided that forces are transferred to the respective base material, i.e. steel and concrete.
The application guidelines in anchor approvals must be observed. Loading values according to approval status July 2005.
The deflection (deformation) of L/150 was observed in all cases, this being measured at the point of load application.
page 124
Installation channels
Features:
■ Serrated C-section.
■ Installation assisted by dimension marking.
■ Great flexibility due to slots.
■ Aesthetic appearance.
■ Double channels laser welded along both sides.
Technical data:
Material: Stainless steel, 1.4301(A2)
Stainless steel, 1.4571(A5)
Single channels ➀ 100

➁ 100
Stainless steel, 1.4301(A2) 2 2
20.6 63x13.5 63x13.5

Channel Length Metal thickness Weight Ordering Item no. 22.3
41.3
height (mm) (m) (mm) (kg/m) designation 7.5

22.3
➀
41.3 7.5
21 3 2 1.45 MQ-21-RA2 3 m 303990 41.3
21 6 2 1.45 ➀ MQ-21-RA2 6 m 303991
41 3 2 2.09 ➁ MQ-41-RA2 3 m 303994 ➂ 100
41 6 2 2.09 ➁ MQ-41-RA2 6 m 303995 2.5
63x13.5
Stainless steel, 1.4571(A5) 52
22.3
21 3 2 1.47 ➀ MQ-21-R 3 m 303988

21 6 2 1.47 ➀ MQ-21-R 6 m 303989
41 3 2 2.12 ➁ MQ-41-R 3 m 303992
41 6 2 2.12 ➁ MQ-41-R 6 m 303993
52 3 2.5 3.00 ➂ MQ-52-R 3 m 303996
52 6 2.5 3.00 ➂ MQ-52-R 6 m 303997
Channels ➂ firestop tested
IBMB no. 3897/1802-5
Double channels ➀ 100 ➁ 100

63x13.5
22.3 63x13.5
41 3 2 2.92 ➀ MQ-21D-RA2 3 m 304000 41.3
7.5
41 6 2 2.92 ➀ MQ-21D-RA2 6 m 304001 22.3

7.5
41.3

Channel Length Metal thickness Weight Ordering Item no.
height (mm) (m) (mm) (kg/m) designation
41 3 2 2.96 ➀ MQ-21D-R 3 m 1)
303998
41 6 2 2.96 ➀ MQ-21D-R 6 m1) 303999
82 3 2 4.27 ➁ MQ-41D-R 3 m 304002
82 6 2 4.27 ➁ MQ-41D-R 6 m 304003
1)
Will initially be supplied as the MN-version.
Channels ➁ firestop tested
IBMB no. 3897/1802-5
page 125
Cantilever Brackets
Features:
■ Serrated C-section.
■ Installation assisted by dimension marking.
■ Great flexibility due to slots.
■ Double-channel brackets welded all around.
Technical data:
Brackets ➀ 6
➁ 8
300; 450
300; 450; 600
20x14 20x14
Channel Channel Weight Packaging Ordering Item no. 80 125
80 125
length (mm) section each (g) conctents (pcs) designation
300 MQ-21-R 670 10 ➀ MQK-21/300-R 284388
450 MQ-21-R 890 10 ➀ MQK-21/450-R 304004 50
50
300 MQ-41-R 950 10 ➁ MQK-41/300-R 304005
450 MQ-41-R 1260 10 ➁ MQK-41/450-R 304006
600 MQ-41-R 1570 8 ➁ MQK-41/600-R 304007 ➂ 8
➃ 10
450 MQ-21D-R 1720 10 ➂ MQK-21D/450-R 304008 450 750
750 MQ-41D-R 2730 4 ➃ MQK-41D/750-R 304009 20x14

20x14
80 125
165
Brackets ➁ ➃ firestop tested

120
50
60
IBMB no. 3897/1802-5
Angle brace
L 74
For fabricating wall brackets with individual stand-off lengths. 11
Material: 1.4571 (A5)

Material thickness: 4 or 3 mm
Weight Pakaging Ordering Artikel-Nr.
A H L α each (g) contents (pcs) designation A
H
Angle brace, short 355 328 324 45° 650 10 MQK-SK-R 304011
Angle brace, long 635 528 524 45° 1060 10 MQK-SL-R 304010
(See technical data on page 36) 33
13.5
page 126
Channel nut
Features:
■ Simple, compact, time saving.
■ Single part which can be prefitted.
■ Easy to use.
■ Universal: one and the same nut for all channels.
Technical data:
Material: Stainless steel
Pushbutton
Bolt: M10 material A4-70 as per DIN EN ISO 3506-1

Width across flats: 17 mm
Nut: 1.4581 as per DIN EN 10 283
Plate: 1.4401 (A4) as per DIN 17 440
Connection Weight Packaging Outside packaging Ordering Item no.
thread each (g) contents (pcs) contents (pcs) designation
M10 77 25 200 MQN-R 304012
Rec. tensile load, Rec. shear load, Tightening torque

Zrec (kN) Qrec (kN) MD (Nm)
Item Channel I Channel II IBMB no. 3897/1802-5
MQN-R 5.0 8.0 5.0 40 1)
Channel I: MQ-21, MQ-41, MQ-21D, MQ-41D (stainless steel)

Channel II: MQ-52 (stainless steel)
1)
Shear loading applies to single fastening. Qrec (kN) 9.0 for two fastenings
Wing nut M 6
M 8
M10
M12
Nut, M6–M12: 1.4581 as per DIN EN 10 283

Plastic: PA
M6 29 25 500 MQM-M6-R 304014
M 8 27 25 500 MQM-M8-R 304015
M10 25 25 500 MQM-M10-R 304016
M12 23 25 500 MQM-M12-R 304017
Rec. tensile load, Rec. shear load, Tightening torque

Zrec (kN) Qrec (kN) MD (Nm)
Item Channel I Channel II (bolt A4-70)
MQM-M 6-R 3.0 3.0 1.5 10
MQM-M 8-R 5.0 5.0 3.5 20
MQM-M10-R 5.0 8.0 5.0 40
MQM-M12-R 5.0 8.0 5.0 40
page 127
Pipe ring saddle

Features:
■ Single part, simple and time-saving in use.
■ For all types of channels.
■ For threaded rods from M8 to M16.
Technical data:
MQA-R pipe ring saddle

M 8
Nut: 1.4581 as per DIN EN 10 283 M10
Plate: 1.4401 (A4) as per DIN 17 440 M12
M16
Plastic: PB
M8 75 25 200 ➀ MQA-M 8-R 304021
M10 73 25 200 ➁ MQA-M10-R 304022
M12 71 25 200 ➁ MQA-M12-R 304023
M16 84 25 200 ➁ MQA-M16-R 304024
Rec. tensile load, Tightening torque Bending moment, threaded
Zrec (kN) MD (Nm) rod A4-70 (Nm) 1)
Item Channel I Channel II
MQA-M 8-R 3.0 3.0 9 12.1
MQA-M10-R 5.0 7.0 18 24.1
MQA-M12-R 5.0 8.0 31 42.1
MQA-M16-R 5.0 8.0 40 100.0
1)
Calculation as per DIBt
Pipe ring saddles ➁ firestop tested
IBMB no. 3897/1802-5
MQG-2-R base plate M16

1/2" 155
50
3/4"
Material: 1.4571 (A5) 1"
Connection Weight Packaging Ordering Item no.

thread each (g) contents (pcs) designation
100
M16 180 20 MQG-2-M16-R 304028
1
/2″ 170 20 MQG-2-1/2″-R 304029
3
/4″ 185 20 MQG-2-3/4″-R 304030
1″ 205 20 MQG-2-1″-R 304031
Rec. tensile load, Rec. shear load, Tightening torque Bending moment,
Item Zrec (kN) Qrec (kN) MD (Nm) threaded rod A4-70 (Nm)
MQG-2-M16-R 6.0 9.0 40 100.0
MQG-2-1/2″-R 6.0 9.0 40 42.1
MQG-2-3/4″-R 6.0 9.0 40 200.0
MQG-2-1″-R 6.0 9.0 40 200.0
page 128
Angles, angle brackets,

connectors
Features:
19
■ Univesal: few parts for all applications. 19.4
■ Easy to use.
■ Three-dimensional, thus high strength.
35 10
■ The MQN-R pushbutton can be prefitted.
Technical data:
Material thickness: 4 mm
90º angle ➀
Weight Packaging Ordering Item no.

each (g) contents (pcs) designation
61
➀
61
Angle, 2 hole, 90° 110 10 MQW-2-R 304051
Angle, 4 hole, 90° 220 10 ➁ MQW-4-R 304054
Angle, 8 hole, 90° 420 10 ➂ MQW-8/90°-R 304055
Angle, 3 hole, 90° 160 10 ➃ MQW-3-R 304052
➁ ➂ ➃ Frec 1.8 x Qrec
(Single value MQN-R A )
55 105 Observe MD
111
A
61
Supported at both ends
Frec. 6.0 kN
45º angle ➀ 105 (double bolted A )
A
45°

Angle, 8 hole, 45° 410 10 ➀ MQW-8/45°-R 304056
Angle, 3 hole, 45° 155 10 ➁ MQW-3/45°-R 304053
➁ 106
45°
56
➀ 110
➁
Angle bracket 198

each (g) contents (pcs) designation 155 198
Angle bracket, one brace 460 10 ➀ MQW-S/1-R 304058 118
➁ MQW-S/2-R
100
Angle bracket, two braces 1180 10 304059

13.5
13.5
167
Connector, two dimensional

112
Connector, triple, two dimensional 602 10 MQV-3/2D-R 304034
55
Connector, three dimensional

each (g) contents (pcs) designation 112
Connector, triple, three dimensional 451 10 MQV-3/3D-R 304035
page 129
Connector, two dimensional 167

Connector, double, two dimensional 440 10 MQV-2/2D-R 304032 112
Longitudinal channel connector 205
45

Channel connector, 12 hole 555 10 MQV-12-R 304037
Channel base / Base material con-

nector
Features:
19
■ Reliable and easy to use. 19.4
■ Connection of channels to any base material.

■ The MQN-R pushbutton can be prefitted. 35 10
Technical data:
Separate design verification of the fastening on the base material
must be provided.
Base material connector 167
112
A
Suitable for Weight Packaging Ordering Item no. Channel
channel height each (g) contents (pcs) designation 112 B
Frec
MQ-41, MQ-21D 440 10 MQV-2/2D-14-R 304033
Frec Channel Bolt Pushbutton Tightening torque

Item (kN) (B) (A) MD (Nm)
MQV-2/2D-14-R 7.8 MQ-41-R Double MQN-R 40
Channel base ➀
A
105
Suitable for Weight Packaging Ordering Item no.
channel height each (g) contents (pcs) designation
➀ MQP-21-72-R
20x14
MQ-21 – MQ-72 1150 12 304047 6
Frec
MQ-41 D 1880 8 ➁ MQP-82-R 304048 80
135
185
Frec Bolt Pushbutton Tightening torque ➁

Item (kN) (A) MD (Nm)
A A
MQP-21-72-R 9,0 Double MQN-R 40 106
MQP-82-R 12,6 Quadruple MQN-R 40 20x14

Frec
8
150
Channel base 햲 firestop tested 100 200
IBMB no. 3897/1802-5
page 130
MQP-U-R universal joint
Features
■ Universal fastening on inclined components.
■ Direct connection to the building structure and on installation
channels, especially suitable for braces and fixed points.
■ Angle steplessly adjustable up to 90°.
■ Easy to use.
Technical data
Cast part material: GX5CrNiMoNb19-11-2
Bolt material: GX5CrNiMoNb19-11-2
Separate design verification of the fastening on the base material must
be provided.
Our technical advisory service would be pleased to assist with the
design calculations for fixed points.
Supplied complete with washer and nut.
Thread Hole diameter D2 Weight each Packaging Ordering Item no.

D1 (mm) (g) contents (pcs) designation
M12 12.5 325 10 MQP-U M12/12-R 284251
M12 16.5 320 10 MQP-U M12/16-R 285915
M16 16.5 315 10 MQP-U M16/16-R 284252
Item Frec (kN) Frec (kN) Frec (kN) Tightening torque locking nut MD
(0°–30°) (> 30°–60 °) (> 60°–90°) (Nm)
MQP-U M12/12-R 11.0 9.0 7.5 80
MQP-U M12/16-R 14.0 14.0 11.0 80
MQP-U M16/16-R 14.0 14.0 11.0 120
Frec
variable
angle
page 131
Beam clamp
Features:
■ For connecting installation channels to steel beams without drilling
or welding.
≤
■ The clamp set fits all standard T-beams
(max. clamping thickness 23 mm).
Technical data:
max. clamping thickness

MQT-R beam clamp ➀23mm p g
➁23mm
54 54
M10
U-bolt: 1.4401 (A4) M10
Claw plate: 1.4401 (A4)
Nut: A4-70 as per DIN EN ISO 3506-2 127
85 30
65
75
channel height each (g) contents (pcs) designation 6 75
6
MQ-21, MQ-41, MQ-21D 427 10 ➀ MQT-21-41-R 304067
MQ-52, MQ-41D 471 10 ➁ MQT-52-82-R 304068
Tightening torque Max. rec. load

Beam clamp MD (Nm) (kN)
MQT-21-41-R 10 3.0
MQT-52-82-R 20 4.5
Always use beam clamps in pairs.
Channel loading values must be allowed for.
MQT-C-R beam clamp 33.5

20
Clamp: 1.4401 (A4)

Screw: M12, material A4-70 as per DIN EN ISO 3506-1
Suitable for Material Weight Packaging Outside packaging Ordering Item no.
channel height thickness (mm) each (g) contents (pcs) contents (pcs) designation 10 40 M 12
MQ-21, MQ-41 10 260 6 48 MQT-C23-R 304069
Tightening torque Max. rec. load

Beam clamp MD (Nm) (kN)
MQT-C23-R 40 2.5
Always use beam clamps in pairs.
Channel loading values must be allowed for.
page 132
Clamp
Features: 19.4 19
■ Universal: few parts for all applications.
■ Easy to use.
■ The MQN-R pushbutton can be prefitted. 35 10
Technical data:
Clamps ➀ ➁
161 161
106 106
channel height each (g) contents (pcs) designation
MQ-21 210 10 ➀ MQB-21-R 304060
MQ-41, MQ-21D 240 10 ➁ MQB-41-R 304061
MQ-52 340 10 ➂ MQB-52-R 304062
MQ-41D, MQ-41, MQ-21D 340 10 ➃ MQB-82-R 304063
➂ ➃ 161
161
106 106
page 133
Accessories
Features:
■ Machting items in programme.
Technical data:
52.5
Boss plate 45.5
5
Thread Weight Packaging Ordering Item no. 7.5
9.5
each (g) contents (pcs) designation 11.5
M 6 94 20 MQZ-L7-R 304070 13.5
17.5
M 8 92 20 MQZ-L9-R 304071
M10 88 20 ➀ MQZ-L11-R 304072
M12 84 20 ➀ MQZ-L13-R 304073
M16 80 20 ➀ MQZ-L17-R 304074
Boss plates ➀ firestop tested
IBMB no. 3897/1802-5
Installation washer 28
34.2
Hole diameter Weight Packaging Ordering Item no. 10.5

(mm) each (g) contents (pcs) designation
10,5 30 40 MQZ-U-R 304084
Adaptor M12
M16
Material: 1.4401 (A4) 1/2"
3/4"
Internal External Width across Weight Packaging Ordering Item no.
thread thread flats (mm) each (g) contents (pcs) designation
M12 M10 18 41 25 MQZ-A-M12/M10-R 284389 47.5
M16 M12 19 92 25 MQZ-A-M16/M12-R 304079 16
1
/2″ M16 24 109 25 MQZ-A-1/2″/M16-R 304080 M10
M12
3
/4″ M16 30 135 25 MQZ-A-3/4″/M16-R 304081
M16
Channel endcap
Made of polypropylene (PP), suitable for all installation channels.
channel height each (g) contents (pcs.) designation
MQ-21, MQ-21D 2 50 ➀ MQZ-E21 370598
2 50 ➁ MQZ-E31* 369686
MQ-41, MQ-41D 2 50 ➂ MQZ-E41 369685
* Usable for MQ-52- and MQ-72-channel sections.
➀ ➁ ➂
21
31
41.3
page 134
3D system
Features:
Bracing with predetermined bending point.
Technical data:
Material: Stainless steel, 1.4571 (A5)
Width across flats: 17mm
Tightening torque: 40Nm
Description Weight Packaging Ordering Item no.

Brace 73 20 MQ3D-A-R 304085
Note:
When installing the brace, an M10-screw of A4-70 grade must be used.
The min. length of screw thread engagement must be observed.
MRG-R roll connector
Features:
µ
Smooth rolling on coated rollers. Large movement: MRG 2-R up to
Technical data: Coefficient of friction: 0=0.15 80mm, MRG-D6-R up to 116mm.
Material: Stainless steel 1.4571 (A5) Center mark for setting to zero.
Delivery without nut. washer or bolt
11.5 x 20
MRG 2-R
MRG 2-R roll connector
IBMB no. 3897/1802-5 80
Weight F Max. dispacement Max. dispacement Packaging ordering Item no.
each (g) (kN) axial (mm) transverse (mm) contents (pcs) designation
M10 / M12 1.5 80 - 4 MRG 2-R 304086
Delivery without nut. washer or bolt
MRG-D6-R double roll connector

MRG - D6 - R
Two connection bosses
Weight F Max. dispacement Max. dispacement Packaging ordering Item no.
each (g) (kN) axial (mm) transverse (mm) contents (pcs) designation
M12 / M16 6.0 116 - 2 MRG-D6-R 304087
90
13.5 x 20
page 135
MP-SRNI / MP-SRN pipe rings

For fastening pipes up to 64 mm
in corrosive surroundings
Fields of application:
■ Heating and industry
■ Food industry (except production)
■ Water treatment
Benefits:
■ Pipe ring with passive fire prevention verification as per DIN 4102, part 2
■ Resistance-welded connection boss
■ High resistance to corrosion (A5 stainless steel)
■ Clamping bolt secured against loss
■ Non-slip (bonded), pre-fitted rubber inlay
Technical data:
Max permissible tensile load:
MP-SRNI / MP-SRN up to 64 mm diameter Frec. = 1500 N
Pipe ring material: A5 1.4571 / DIN 17441
Clamping bolts: slotted hexagon head
Rubber inlay material: EPDM
Temperature resistance: –50°C to +120°C
Shore A hardness (DIN 53 505): 50 ± 5
Noise reduction: ∆
LA = 15 dB (A)
Stability: aging, ozone, weather and hot water resistant
MP-SRNI pipe ring

With metric connection boss
and insulating inlay as per DIN 4109
M8 SW13 firestop
h
8
s
ød
M10 SW17
10
bs
Building
material class
b
B2
„Normal flammability“
as per DIN 4102
Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item no.
(mm/ inch) d (mm) width across flats bolts bs (mm) b × s (mm) h (mm) contents (pcs) designation
3
/8″ 15.5–18.5 M8 / SW13 M6 55 17.5 × 2 19 25 MP-SRNI 17 374186
1
/2″ 19.5–22.5 M8 / SW13 M6 61 17.5 × 2 22 25 MP-SRNI 21 374187
3
/4″ 25.5–28.5 M8 / SW13 M6 68 17.5 × 2 25.5 25 MP-SRNI 27 374188
1″ 33.0–37.0 M8 / SW13 M6 76 17.5 × 2 29.5 25 MP-SRNI 34/36 374189
11/4″ 38.0–44.0 M10 / SW17 M8 82 17.5 × 2 34.5 25 MP-SRNI 38/42 374192
11/2″ 48.0–52.0 M10 / SW17 M8 91 17.5 × 2 39 25 MP-SRNI 48/50 374193
57 54.0–58.0 M10 / SW17 M8 97 17.5 × 2 42 25 MP-SRNI 57 374194
2″ 59.0–64.0 M10 / SW17 M8 102 17.5 × 2 44.5 10 MP-SRNI 60/63 374195
page 136
MP-SRN pipe ring

without insulating inlay
M8 SW13
h
8
ød
s
M10 SW17
10
bs
b
Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item no.
(mm/ inch) d (mm) width across flats bolts bs (mm) b × s (mm) h (mm) contents (pcs) designation
3
/8″ 15.5–18.5 M8 / SW13 M6 51 17.5 × 2 17 25 MP-SRN 17 254697
1
/2″ 19.5–22.5 M8 / SW13 M6 55 17.5 × 2 19 25 MP-SRN 21 254698
3
/4″ 25.5–28.5 M8 / SW13 M6 61 17.5 × 2 22 25 MP-SRN 27 254669
1″ 32.5–35.5 M8 / SW13 M6 68 17.5 × 2 25.5 25 MP-SRN 34 254700
36 34.5–37.5 M10 / SW17 M6 70 17.5 × 2 28.8 25 MP-SRN 36 254701
38 36.5–39.5 M10 / SW17 M6 72 17.5 × 2 29.5 25 MP-SRN 38 254702
11/4″ 40.5–43.5 M10 / SW17 M6 76 17.5 × 2 31.5 25 MP-SRN 42 254703
11/2″ 46.5–51.5 M10 / SW17 M8 82 17.5 × 2 34.5 25 MP-SRN 48/50 254704
57 55.5–58.5 M10 / SW17 M8 91 17.5 × 2 39 25 MP-SRN 57 254705
2″ 58.5–61.5 M10 / SW17 M8 94 17.5 × 2 40.5 10 MP-SRN 60 254706
63 61.5–64.5 M10 / SW17 M8 97 17.5 × 2 42 10 MP-SRN 63 254707
page 137
MP-MRI pipe rings

For pipe fastenings in corrosive surroundings
≤
in the medium-duty diameter range
from 21/2 to 219 mm
■ Water treatment
Benefits:
■ Pipe ring with passive fire prevention verification as per DIN 4102, part 2
■ Solid connection boss, welded all round
■ Greater stiffness from profiled pipe ring steel band
■ Material suitable for pipe diameter. Loads up to 5,000 N
■ High resistance to corrosion (A5 stainless steel)
■ Clamping bolt secured against loss
■ Non-slip (bonded), pre-fitted rubber inlay
Technical data:
Max permissible load for suspensions
68 mm to 3″ diameter, Frec. = 3000 N
101.6 mm to 6″ diameter, Frec. = 4000 N
177.8 to 219.1 mm Frec. = 5000 N
Clamping bolts: slotted hexagon head
Temperature resistance: –50 to +120°C
Shore A hardness (DIN53 505): 50± 5
∆
Building
material class
Noise reduction: LA = 18 dB (A) B2
„Normal flammability“
Stability: aging, ozone, weather and hot water resistant as per DIN 4102
firestop
MP-MRI pipe ring

Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item
(mm/ inch) d (mm) width across flats bolts bs (mm) b × s (mm) h (mm) contents (pcs) designation no.
68/72 68– 72 M10 / SW17 M8 129 24 × 2.0 50 10 MP-MRI 68/72 372044
21/2″ 70– 77 M10 / SW19 M8 136 24 × 2.0 48 10 MP-MRI 21/2″ 372045
78/84 78– 84 M10 / SW19 M8 145 24 × 2.0 54 10 MP-MRI 78/84 372046
3″ 82– 90 M10 / SW19 M8 150 24 × 2.0 53 10 MP-MRI 3″ 372047
101.6 97–103 M12 / SW19 M8 172.5 30 × 2.5 64.5 5 MP-MRI 101.6 372048
4″ 108–114 M12 / SW19 M8 183.5 30 × 2.5 70 5 MP-MRI 4″ 372049
117 114–119 M12 / SW19 M8 189 30 × 2.5 73.5 5 MP-MRI 117 372050
125 122–127 M12 / SW19 M8 197 30 × 2.5 77.5 5 MP-MRI 125 372051
133 132–137 M12 / SW19 M8 207 30 × 2.5 82.5 10 MP-MRI 133 372052
5″ 137–142 M16 / SW21 M8 212 30 × 2.5 89 10 MP-MRI 5″ 372053
159 156–162 M16 / SW21 M8 232 30 × 2.5 97 10 MP-MRI 159 372054
6″ 162–168 M16 / SW21 M8 238.5 30 × 2.5 101 10 MP-MRI 6″ 372055
177.8 175–180 M16 / SW21 M8 252.5 30 × 3.0 109.5 10 MP-MRI 177.8 372056
193.7 190–200 M16 / SW21 M8 271 30 × 3.0 115 10 MP-MRI 193.7 372057
212 210–219 M16 / SW21 M8 291 30 × 3.0 125.5 10 MP-MRI 212 372058
219.1 217–224 M16 / SW21 M8 296 30 × 3.0 129.5 10 MP-MRI 219.1 372059
page 138
MP-MR pipe ring

without insulating inlay
M16 SW24
16
h
ød
s
M12 SW19
12
bs M10 SW17
10
b
(mm/ inch) d (mm) width across flats bolts bs (mm) b × s (mm) h (mm) contents (pcs) designation no.
68/72 68– 72 M10 / SW17 M8 117,5 24 × 2,0 43,5 10 MP-MR 68/72 374197
21/2″ 75– 80 M10 / SW17 M8 129 24 × 2,0 50 10 MP-MR 21/2″ 374198
3″ 87– 93 M10 / SW17 M8 145 24 × 2,0 54 10 MP-MR 3″ 374200
101,6 97–104 M12 / SW19 M8 160 30 × 2,5 60 5 MP-MR 101,6 374201
4″ 109–114 M12 / SW19 M8 172,5 30 × 2,5 64,5 5 MP-MR 4″ 374202
117 116–123 M12 / SW19 M8 180 30 × 2,5 70 5 MP-MR 117 374203
125 125–131 M12 / SW19 M8 189 30 × 2,5 73,5 5 MP-MR 125 374204
133 133–138 M12 / SW19 M8 197 30 × 2,5 77,5 10 MP-MR 133 374205
5″ 139–145 M16 / SW21 M8 202,5 30 × 2,5 81,5 10 MP-MR 5″ 374206
159 156–162 M16 / SW21 M8 226 30 × 2,5 94 10 MP-MR 159 374207
6″ 162–168 M16 / SW21 M8 232 30 × 2,5 97 10 MP-MR 6″ 374208
177.8 175–180 M16 / SW21 M8 242,5 30 × 3,0 106,5 10 MP-MR 177,8 374209
193.7 190–200 M16 / SW21 M8 262 30 × 3,0 112 10 MP-MR 193,7 374210
212 210–219 M16 / SW21 M8 281,5 30 × 3,0 122,5 10 MP-MR 212 374211
219.1 217–224 M16 / SW21 M8 286,5 30 × 3,0 126,5 10 MP-MR 219,1 374212
page 139
MP-MRXI pipe ring

For pipe fastenings in corrosive surroundings
in the diameter range 244 to 508 mm
■ Water treatment
Benefits:
■ Solid connection boss, welded all round
■ High loading capacity up to 13,000 N
■ Strong half-rings (hoops) for high stability
■ Strong clamping bolts (M16) for high loads
Building
■ High resistance to corrosion (A5 stainless steel) material class
B2
■ Non-slip (bonded), pre-fitted rubber inlay „Normal flammability“
as per DIN 4102
Technical data:
Max permissible load for suspensions
244.5 to 406 mm diameter, Frec. = 10000 N
457 to 508 mm diameter, Frec. = 13000 N
Temperature resistance: –50 to +120°C
Shore A hardness (DIN53 505): 50 ± 5
Noise reduction: ∆
LA = 16 dB (A)
Stability: aging, ozone, weather and hot water resistant
Not for use in painting processes
MP-MRXI pipe ring

(mm) d (mm) width across flats bolts bs (mm) b × s (mm) h (mm) contents (pcs) designation no.
244.5 244–253 M16 / SW21 M16 355 50 × 4 147.5 10 MP-MRXI 244,5 374213
273 267–274 M16 / SW21 M16 372 50 × 4 156 10 MP-MRXI 273 374214
280 275–282 M16 / SW21 M16 384 50 × 4 162 10 MP-MRXI 280 374215
324 314–324 M16 / SW21 M16 441 50 × 4 182.5 1 MP-MRXI 324 374216
326 324–330 M16 / SW21 M16 445 50 × 4 184.5 1 MP-MRXI 326 * 374217
355 348–356 M16 / SW21 M16 471 50 × 4 197.5 1 MP-MRXI 355 * 374218
406 400–409 M16 / SW21 M16 524 50 × 4 224 1 MP-MRXI 406 * 374219
457 454–462 M16 / SW21 M16 585 70 × 5 251.5 1 MP-MRXI 457 * 374220
508 500–508 M16 / SW21 M16 631 70 × 5 274.5 1 MP-MRXI 508 * 374221
* Available on request
page 140
Stainless steel accessories for pipe rings d

H
∅a
Base plate
Material: 1.4571 (A5) stainless steel
Version: Connection boss boss welded all round
Connection boss H a Max. load Shear load for Package Ordering Item no.
109
[D] [mm] [mm] F [kN] A = 150 mm [kN] cont. (pcs) designation 150 100
M16 hex. 16 13.5 12.5 2.0 25 MFP-GP-R M16 376258
3
/4″ boss 17 13.5 12.5 2.0 25 MFP-GP-R 3/4″ 376259
The means of fastening to the base material, e. g. anchors, requires separate verification.
Adaptor I
Material: 1.4401 (A4) stainless steel

Fits MP-MXRI / MP-MRI / MP-MR pipe rings with M16 or M12 boss and MFP-GP-R M16 and LI
MFP-GP-R 3/4″ base plates L
Outside Inside Wrench Length Outside Package Ordering Item no. LA

thread thread size L LA LI dia. contents designation A
[A] [I] [SW] [mm] [mm] [mm] [mm] (pcs)
M12 /4″
3
30 39.5 11.5 28 34 25 MGA-R /4″ IG / M12 AG
3
376256
M16 /4″
3
30 43.5 15.5 28 34 25 MGA-R 3/4″ IG / M16 AG 376257
MGL 2-R base plate «light» (A5), metric two-hole version d

9 x 16
Version: Spot-welded connection boss 30
d H a×b FZrec Package Ordering Item no.
[mm] [mm] [mm] [kN] cont. (pcs) designation 3
H
M8 11 9×16 1.9 10 MGL 2-R-M8 246927 54
80
MGS 2-R base plate «standard» (A5), metric two-hole ver- d

11 x 18
sion 40
Version: Spot-welded connection boss 4

d H a×b FZrec Package Ordering Item no. H
[mm] [mm] [mm] [kN] cont. (pcs) designation 85
M10 14 11×18 2.0 10 MGS 2-R-M10 246931 120
M12 16 11×18 3.0 10 MGS 2-R-M12 247762
M16 20 11×18 3.5 10 MGS 2-R-M16 246932
Suitable anchor systems:
HKD-SR HST-R
HIT HVZ-R / HVA-R
page 141
Installation Accessories
Threaded rod DIN 976
Material: A4-70 as per DIN 267-11
Thread size [M] Length L [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no.
M5 1000 320 25 AM 5x1m A4 47907
M6 1000 320 25 AM 6x1m A4 58949
M8 1000 320 25 AM 8x1m A4 58666
M8 3000 960 25 AM 8x3m A4 58706
M10 1000 500 20 AM 10x1m A4 58670
M10 3000 1500 20 AM 10x3m A4 58707
M12 1000 730 10 AM 12x1m A4 58671
M12 3000 2190 15 AM 12x3m A4 58709
M16 1000 1330 5 AM 16x1m A4 58683
M16 3000 3990 10 AM 16x3m A4 58712
M20 1000 2100 5 AM 20x1m A4 58688
M20 3000 6300 1 AM 20x3m A4 58715
M24 1000 6300 1 AM 24x1m A4 58689
Hexagon head bolt DIN - EN - ISO 4017 d
s
Material: A4-70 DIN 267 e L
k
DA L(mm) e (mm) S(mm) k(mm) Packaging contents (pcs) Ordering designation Item no
M8 20 14,38 13 5,3 100 M 8 x 20 A4 87640

M8 25 14,38 13 5,3 100 M 8 x 25 A4 87637
M10 20 18,90 17 6,4 100 M 10 x 20 A4 26839
M10 25 18,90 17 6,4 100 M 10 x 25 A4 87632
M12 20 21,10 19 7,5 100 M 12 x20 A4 387988
M 12 25 21,10 19 7,5 50 M 12 x 25 A4 87634
M 16 30 26,75 24 10,0 25 M 16 x 30 A4 230322
DI
Inside hexagon head bolt, Flat Washer, 40mm O.D S
DIN-EN-ISO 4762 Material: A4 DA
DA S(mm) DI (mm) Ordering designation Item no

Material: A4 40 3,0 8,4 A 8,4 - 40A4 41141
DA L(mm) s (mm) k(mm) Ordering designation Item no
40 3,0 10,5 A 10,5 - 40A4 41142
M8 16 6 8 M 8 x16 A4 230571 40 3,0 13 A 13 - 40A4 41143
M 10 16 8 10 M 10 x 16 A4 230572 40 3,0 17 A 17 - 40A4 41144
d
Hexagon nut DIN-EN-ISO 4032 s
Material: A4-70 DIN 267 m
DA Packaging contents (pcs) Ordering designation e Item no.

M6 100 M 6 A4 52459
M8 100 M 8 A4 52460
M10 100 M 10 A4 52461
M12 100 M 12 A4 52462
M 16 50 M 16 A4 52463
M 20 50 M 20 A4 387992
M 24 50 M 24 A4 387993
DI
Flat Washer DIN-EN-ISO 7089 S
Material: A4 DA
DA Size Packaging contents(pcs) Ordering designation Item no.

12 6 100 A 6,4 A4 58922
16 8 100 A 8,4 A4 58622
20 10 100 A 10,5 A4 58042
24 12 100 A 13 A4 58041
30 16 100 A 17 A4 387989
37 20 100 A 21 A4 387990
44 24 100 A 25 A4 387991
GR-G threaded pipe EDELSTAHL ®
Stainless
steel
Material: Stainless steel, 1.4404 (A4-70)
M L
Inch size Lenght L (mm) Weight each(g) Packaging contents (pcs) Ordering designation Item no.
1
⁄2 " 2000 1800 10 GR-G ⁄2"-A4ⴛ2 m
1
286862
3
⁄4" 2000 2800 5 GR-G 3⁄4"-A4ⴛ2 m 286863
1" 2000 4880 5 GR-G 1"-A4ⴛ2 m 286864
page 142

System MQ: Medium Duty Channel Installation Stainless Steel

Uploaded by

Copyright:

Available Formats

System MQ: Medium Duty Channel Installation Stainless Steel

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

System MQ: Medium Duty Channel Installation Stainless Steel

Uploaded by

Copyright:

Available Formats

System MQ

System ML channel installation

Channel selection diagram (stainless steel) 123

Technical data for brackets (stainless steel) 124

Installation channels 125

Cantiliver brackets 126

Channel nut 127

Pipe ring saddle 128

Angles, angle brackets connectors 129-130

MQP-U-R universal joint 131

Beam clamps 132-133

MP-SRNI / MP-SRN pipe rings 136-137

MP-MRI /MP-MR pipe rings 138-139

MP-MRXI pipe rings 140

Stainless steel accessories for pipe rings 141

Installation accessories 142

Technical data Channel sections (stainless steel)

Selection example: Single load

Solution: 1 kg 1 – 10 0.01 L/2 L/2

to the required span, L = 100 cm.

(stainless steel) Single span (simply supported)

Channel selection table (stainless steel)

L[cm] 41.3 41.3 41.3 41.3 41.3

Max. load, F (kN) / deflection, f (mm)

Technical data for brackets (stainless steel A5)

F1 [N] F1 [N] F1 [N] F2 [N] F3 [N]

HVZ-R adhesive anchor HST-R stud anchor

Bracket L (mm) Brace F1 [N] 1) F1 [N] 1) F1 [N] 1) F2 [N] 1) F3 [N] 1)

Single channels ➀ 100

Stainless steel, 1.4301(A2) 2 2

20.6 63x13.5 63x13.5

height (mm) (m) (mm) (kg/m) designation 7.5

41 6 2 2.09 ➁ MQ-41-RA2 6 m 303995 2.5

Stainless steel, 1.4571(A5) 52

21 3 2 1.47 ➀ MQ-21-R 3 m 303988

Channels ➂ firestop tested

IBMB no. 3897/1802-5

Double channels ➀ 100 ➁ 100

Stainless steel, 1.4301(A2)

41 6 2 2.92 ➀ MQ-21D-RA2 6 m 304001 22.3

Stainless steel, 1.4571(A5)

Channels ➁ firestop tested

IBMB no. 3897/1802-5

450 MQ-21D-R 1720 10 ➂ MQK-21D/450-R 304008 450 750

750 MQ-41D-R 2730 4 ➃ MQK-41D/750-R 304009 20x14

Brackets ➁ ➃ firestop tested

IBMB no. 3897/1802-5

For fabricating wall brackets with individual stand-off lengths. 11

Material: 1.4571 (A5)

Bolt: M10 material A4-70 as per DIN EN ISO 3506-1

Rec. tensile load, Rec. shear load, Tightening torque

MQN-R 5.0 8.0 5.0 40 1)

Channel I: MQ-21, MQ-41, MQ-21D, MQ-41D (stainless steel)

Nut, M6–M12: 1.4581 as per DIN EN 10 283

Rec. tensile load, Rec. shear load, Tightening torque

Pipe ring saddle

MQA-R pipe ring saddle

Pipe ring saddles ➁ firestop tested

IBMB no. 3897/1802-5