CFD-V37

SERVICE MANUAL E Model

Ver 1.0 1999 . 04

Model Name Using CD Section

CFD-V34
Similar Mechanism Tape Section
Optical Pick-up Type KSM-213CDM
Tape Transport Mechanism Type MF-V10-117

SPECIFICATIONS

CD player section Cassette-corder section

System Compact disc digital audio system Recording system 4 -track 2 channel stereo
Laser diode properties Material: GaAlAs Fast winding time Approx. 120 s (sec.) with Sony cassette
Wavelength:780 nm C-60
Emission duration : Continuous Frequency response TYPE1 (normal) : 70 – 10,000 Hz
Laser output : Less than 44.6 µW
(This output is the value measured at a distance General
of about 200 mm from the objective lens surface Speakers Full range : 10 cm dia., 3.2 Ω, cone type
on the optical pick-up block with 7 mm (2)
aperture.) Outputs Headphones jack (stereo minijack)
Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) For 16 – 64 Ω impedance headphones
Number of channels 2 Power output 2.5 W + 2.5 W (at 3.2 Ω, 10 % harmonic
Frequency response 20 – 20,000 Hz + 1/-2 dB distortion)
Wow and flutter Below measurable limit Power requirements For CD radio cassette-corder :
110 – 120 V, 220 – 240 V AC
Radio section Selectable, 50/60 Hz(E4,EA)
Frequency range FM : 87.6 – 107 MHz(E4,EA) 120V 60 Hz(E92)
87.6 – 108 MHz(E92) 9V DC, 6 size D (R 20) batteries
AM : 530 – 1,605 MHz(E4,EA) For memory controller :
530 – 1,710 MHz(E92) 3V DC, 2 size AA (R 6) batteries
IF FM : 10.7MHz
AM : 455kHz
Aerials FM : Telescopic aerial
AM : Built-in ferrite bar aerial

— Continued on next page —

CD RADIO CASSETTE-CORDER

MICROFILM
 CFD-V37
5-5. SCHEMATIC DIAGRAM — TUNER/SYSTEM SECTION — • Refer to page 34 for IC Block Diagrams.

E4,EA MODEL:4.7p
E92 MODEL:3.3K

E92 MODEL
L1,CT1(1/4) L2, CT1(2/4) L4,CT1(4/4)
E92 MODEL FM TRACKING FM FREQUENCY FM FREQUENCY
COVERAGE COVERAGE

C1 47p

27p
E4,EA MODEL
E92 MODEL

220

L3,CT1(3/4)
AM TRACKING

AM

• Waveform

SWITCH
1 IC501 #¡ 1.0V/div
0.1µsec/div

Mark:

Ref.No. E4 MODEL E92 MODEL EA MODEL

4.0MHz 4.0Vp-p
C7 5.6p 5.6p 6.8p

C18,19
C8 3.3p
0.01
1.5p
0.015
3.3p
0.01
2 IC501 &¢ 1.0V/div
1.0µsec/div
R5 330 470 330

28
500kHz 4.5Vp-p
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
470 • C : panel designation.
28
• U : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground un-
der no-signal (detuned) conditions.
no mark : CD PLAY
( ) : FM
[ ] : AM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
32 • Waveforms are taken with a oscilloscope.
• Signal path.
F : FM
f : AM
• Abbreviation
E4 : 220V – 240V AC area
EA : Saudi Arabia
E92 : 120V AV area

— 23 — — 24 — — 25 — — 26 —
CFD-V37
5-6. SCHEMATIC DIAGRAM — POWER SECTION —

23
• Waveform

3 T301 REC 10V/div

10µsec/div

52.75kHz 40Vp-p

32 23
Note: E4,EA MODEL

• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolytics
E92 MODEL
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
Note: The components identified by mark ! or dotted line
POWER TRANSFORMER
with mark ! are critical for safety.
Replace only with part number specified. F902
E92 MODEL 2.5A:E4,EA MODEL
3.15A:E92 MODEL
• U : B+ Line. E4,EA MODEL E4,EA MODEL 250V

• Power voltage is dc 9 V and fed with regulated dc power

supply from battery terminal.
• Voltages and waveforms are dc with respect to ground un-
der no-signal (detuned) conditions.
no mark : CD PLAY
( ) : TAPE PLAY
[ ] : TAPE REC
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
• Signal path.
F : FM
E : PB
a : REC
J : CD

— 27 — — 28 — — 29 — — 30 —
 CFD-V37
5-7. SCHEMATIC DIAGRAM — CD SECTION — • Refer to page 34 for IC Block Diagrams. 5-8. IC BLOCK DIAGRAMS

IC1 CXA12138S

MPX REG
PLL LPF2

AM RF IN

FM RF IN
AM OSC

FM GND
FM OSC

FE OUT
DISCRI

FM/AM
FM RF
MUTE
GND

VCO

REG
AFC
FM
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

FM FRONT-END

AM FRONT-END
REG

FM IF/
VCO MPX REG. DISCRI
1/2 AM
PD1 IF/DET
COUNTER
1/2
PD2 TUNING
COUNTER INDICATOR
AUTOBLEND

MONO/ST MUTING
SELECT
BAND PASS
MUTE
RIPPLE
DECODER AMP FILTER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

R CH OUT

L CH OUT

VCC

RIPPLE
FILTER

AGC AFC1

AGC AFC2

GND

TUNE IND

FM IF IN
AM IF IN
BAND SELECT
VCO CHECK
PLL LPF1
PILOT DET LPF2
PILOT DET LPF2
ST IND/
IC701 CXA1992BR

RF_M

RF_O
RFTC

RF_I
PD2

PD1

CC1

CC2

FOK
PD

LD

CP

CB
39 38 37 36 35 34 33 32 31 30 29 28 27
VEE

–
+

–
+
+
–

+
–
PD RF SUMMING
PD2 IV PD1 IV

+
–
AMP
AMP AMP

+
–
LD +
–
FE_BIAS 40 26 SENS2
• Waveform

–
+
VCC

+
–
+
APC –

4 IC703 &¡ 1.0V/div

50nsec/div F 41 –
VEE IIL
↓ 25 SENS1
+ LASER POWER CONTROL
TTL
F IV AMP VCC

+
–

–
+
–
VCC FE AMP VCC
E 42 – 24 C. OUT

–
+
+
–
+
E IV AMP
VEE
+

–
+
–
3.5Vp-p

–
+
16.9344MHz EI 43 DFCT 23 XRST

IFB4
IFB5
IFB2
IFB3

IFB6
IFB1

+
–
BAL1
BAL2
BAL3
BAL4
+
VEE

5 IC703 #∞

–
+
0.2V/div –
LEVEL S VEE
0.5µsec/div

TGFL
VEE
VEE 44 VEE 22 DATA

TOG4
TOG3
TOG2
TOG1
FO. BIAS

–
–

+
+
WINDOW VCC IIL

+
–
COMP. MIRR
+ ↓

–
+
– TTL TTL
TEO 45 + TRK. GAIN FOK ↓ 21 XLT
– WINDOW COMP. IIL
+ +
– –

DFCT1
LDON
1.2 ± 0.2Vp-p E-F BALANCE

MIRR
LPCL

TGFL
LPC

CC1
LPFI 46 + WINDOW COMP. 20 CLK
+
– FOH
–
FOL
TGH
Note: TGL IIL DATA REGISTER
TEI 47 19 LOCK
• All capacitors are in µF unless otherwise noted. pF: µµF BALH INPUT SHIFT REGISTER
– ADDRESS DECODER
BALL
50 WV or less are not indicated except for electrolytics +
ATSC
SENS SELECTOR
OUTPUT DECODER
and tantalums. TZC
• All resistors are in Ω and 1/4 W or less unless otherwise ATSC 48 –
+
FZC VCC 18 VCC
ATSC
specified. WINDOW
COMP.
DFCTO IFB1-6 FS1-4 TG1-2 TM1-7 PS1-4
Note: The components identified by mark ! or dotted line TZC 49 – BAL1-4 ISET 17 ISET
with mark ! are critical for safety. +
DFCT
TOG1-4
TZC COMP.
Replace only with part number specified. TM1
VCC VCC
• U : B+ Line. TDFCT 50 TRACKING 16 SL_O
VCC TG1 PHASE COMPENSATION
• Power voltage is dc 9 V and fed with regulated dc power TM4 TM6

supply from battery terminal. +

• Voltages and waveforms are dc with respect to ground un- VC 51 –
VCC
15 SL_M

der no-signal (detuned) conditions. TM7

VCC VEE
no mark : CD PLAY FOCUS FS1
TM3
TM5
PHASE COMPENSATION
• Voltages are taken with a VOM (Input impedance 10 MΩ). FZC 52 +
–
+ 14 SL_P
–
Voltage variations may be noted due to normal production VEE VEE
TM2
+ FS2
tolerances. DFCT – Charge
up FSET
• Waveforms are taken with a oscilloscope. FZC COMP.
TG2
• Circled numbers refer to waveforms. FS4

–
+
• Signal path. VEE
J : CD 1 2 3 4 5 6 7 8 9 10 11 12 13
28

FEO

FEI

FDFCT

FGD

FLB

FE_O

FE_M

SRCH

TGU

TG2

FSET

TA_M

TA_O
24

— 31 — — 32 — — 33 — — 34 —