Service Manual: HCD-GR5/RX50

HCD-GR5/RX50
SERVICE MANUAL AEP Model

UK Model
HCD-RX50
E Model
Tourist Model
HCD-GR5
HCD-GR5/RX50 is the tuner, deck, CD

and amplifier section in MHC-GR5/RX50.
Photo: HCD-GR5
Dolby noise reduction manufactured under license from Model Name Using Similar Mechanism HCD-H551
Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trademarks CD CD Mechanism Type CDM28-5BD19
of Dolby Laboratories Licensing Corporation. SECTION Base Unit Type BU-5BD19
Optical Pick-up Type KSS-213BA/F-NP
TAPE Model Name Using Similar Mechanism HCD-H551
DECK
SECTION Tape Transport Mechanism Type TCM-220WR2E
SPECIFICATIONS
CD player section Tourist model:
System Compact disc and digital 76.0 – 108.0 MHz
audio system Other models:
Laser Semiconductor (λ = 780nm) 87.5 – 108.0 MHz
Emission duration: Aerial FM lead aerial
continuous Aerial terminals 75 ohm unbalanced
Laser output Max 44.6 µW* Intermediate frequency
*This output is the value 10.7 MHz
measured at a distance of
200mm from the objective AM tuner section
lens surface on the Optical Tuning range
Pick-up Block with 7mm AEP, UK, East European models:
aperture. MW: 531 – 1,602 kHz (with
Wavelength 780 – 790 nm the interval set at 9 kHz)
Frequency response LW: 153 – 279 kHz (with
2 Hz – 20 kHz (±0.5 dB) the interval set at 3 kHz)
Signal-to-noise ratio German models:
More than 90 dB 531 – 1,602 kHz (with
Dynamic range More than 90 dB the interval set at 9 kHz)
CD DIGITAL OPTICAL OUTPUT EA4,Thailand models:
(Square optical connector jack,rear panel) 531 – 1,710 kHz(with
Wavelength 600nm the interval set at 9 kHz)
Output level -18dBm 530 – 1,710 kHz(with
the interval set at 10 kHz)
Tuner section
FM stereo, FM/AM superheterodyne tuner — Continue on next page —
FM tuner section
East European model:
65.0 – 75.0 MHz,
COMPACT DISC DECK RECEIVER
87.5 – 108.0 MHz
MICROFILM
—1—
Other models: General
MW: 531 – 1,602 kHz (with Power requirements
the interval set at 9 kHz) AEP,UK,German,East European models:
MW: 530 – 1,710 kHz (with 220 – 230 V AC, 50/60 Hz
the interval set at 10 kHz) EA4,Thailand models:
SW: 5.95 – 17.90 MHz 220 – 240 V AC, 50/60 Hz
(with the interval set at 10 kHz) Other models:
Antenna AM loop antenna, 110 – 120 V, 220 – 240 V
External antenna terminals AC, 50/60 Hz
Intermediate frequency Adjustable with the voltage selector
450 kHz Power consumption
95 W
Dimensions Approx. 280 x 330 x 360 mm
Amplifier section (11 1/8 x 13 x 14 1/4 in)
(AEP,UK,German,East European models) (w/h/d)
DIN power output incl. projecting parts and
40W+40W (6 ohms, at controls
1kHz, DIN) Mass Approx. 7.5 kg (16 lb 9 oz)
Continuous RMS power output
50W+50W (6 ohms, at Design and specifications are subject to
1kHz, 10% THD) change without notice.
Music power output
85W+85W (6 ohms, at
1kHz, 10% THD)
(Other models)
Peak music power output
• Abbreviation
800W
EA4: Without voltage selector Saudi Arabia model
Continuous RMS power output
50W+50W (6 ohms, at
1kHz, 10% THD)
Inputs
MIX MIC (phone jacks):
sensitivity 1 mV,
impedance 10 kilohms
AUDIO IN:
Audio (Phono Jacks)
Voltage 450mV
Impedance 47 kilohms
Outputs
PHONES (stereo phone jack):
accepts headphones of 8 ohms
or more.
SPEAKER: accepts impedance of 6 to
16 ohms.
AUDIO OUT:
Audio (Phono Jacks)
Voltage 450mV
Impedance 1 kilohms
GR5 model:
SUPPER WOOFER:
Voltage 1 V, impedance
1 kilohms
Tape player section
Recording system
4-track 2-channel stereo
Frequency response
(DOLBY NR OFF)
40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
40 – 14,000 Hz (±3 dB),
using Sony TYPE II cassette
Wow and flutter
0.3% W.RMS (NAB)
—2—
MODEL IDENTIFICATION CAUTION
— BACK PANEL — Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Parts No.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing

• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation

MODEL PARTS No. exceeding the limit for Class 1.
GR5 : E model 4-988-833-0π
GR5 : EA3,Taiwan, Tourist model 4-988-833-1π This appliance is classified as
GR5 : Singapore,Malaysia model 4-988-833-2π a CLASS 1 LASER product.
The CLASS 1 LASER
GR5 : Hong Kong model 4-988-833-3π
PRODUCT MARKING is
GR5 : Indonesian model 4-988-833-4π located on the rear exterior.
GR5 : EA4,Thailand model 4-988-833-5π
RX50 : AEP,German model 4-988-834-0π
RX50 : UK model 4-988-834-1π
This caution
RX50 : East European model 4-988-834-2π
label is located
inside the unit.
• Abbreviation
EA3: With voltage selector Saudi Arabia model.
EA4: Without voltage selector Saudi Arabia model.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED

LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND
IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
—3—
TABLE OF CONTENTS
1. SERVICING NOTE .................................................... 5
2. GENERAL .................................................................... 6
3. DISASSEMBLY
3-1. Front Panel ....................................................................... 8
3-2. TC Mechanism Deck ....................................................... 8
3-3. HP Board, JOG Board and PANEL Board ...................... 9
3-4. CD Block ......................................................................... 10
3-5. CD Mechanism Deck ....................................................... 10
4. MECHANICAL ADJUSTMENTS ......................... 11
5. ELECTRICAL ADJUSTMENTS
DECK Section ......................................................................... 11
TUNER Section ....................................................................... 14
CD Section .............................................................................. 16
6. DIAGRAMS
6-1. Block Diagrams
• CD Section ..................................................................... 18
• Main Section ..................................................................19
• Tuner Section
(AEP, UK, German, East European Model) .................. 21
• Tuner Section (Tourist Model) ..................................... 22
• Deck Section .................................................................. 23
6-2. Circuit Boards Location ................................................... 24
6-3. Printed Wiring Board — Panel Section —........................ 25
6-4. Schematic Diagram — Panel Section — ...................... 27
6-5. Schematic Diagram — Main Section — ........................ 31
6-6. Printed Wiring Board — Main Section — ...................... 35
6-7. Schematic Diagram — Deck Section — ........................ 39
6-8. Printed Wiring Board — Deck Section — ...................... 43
6-9. Schematic Diagram — CD Section — ............................ 46
6-10.Printed Wiring Board — CD Section — ......................... 49
6-11.Schematic Diagram — Tuner Section —
(AEP, UK, German, East European Model)...................... 52
6-12.Schematic Diagram — Tuner Section —
(Tourist Model) ................................................................. 55
6-13.Printed Wiring Board — Tuner Section —
(AEP, UK, German, East European Model) ..................... 58
(Tourist Model) ................................................................ 59
6-14.IC Pin Functions
• IC501 Graphic Control (µPD78042FGF-027-3B9)........ 61
• IC701 Master Control (TMP87CP64YF-6521).............. 62
6-15.IC Block Diagrams .......................................................... 65
7. EXPLODED VIEWS
7-1. Case Section ..................................................................... 71
7-2. Back Panel Section .......................................................... 72
7-3. Front Panel Section 1 ....................................................... 73
7-4. Front Panel Section 2 ....................................................... 74
7-5. CD Mechanism Section (CDM28-5BD19) ...................... 75
7-6. Base Unit Section (BU-5BD19) ....................................... 76
7-7. TC Mechanism Section 1 (TCM-220WR2E) .................. 77
7-8. TC Mechanism Section 2 (TCM-220WR2E) .................. 78
8. ELECTRICAL PARTS LIST ....................................79
—4—
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK NOTES ON LASER DIODE EMISSION CHECK
OR BASE UNIT
The laser beam on this model is concentrated so as to be focused on
The laser diode in the optical pick-up block may suffer electrostatic the disc reflective surface by the objective lens in the optical pick-
break-down because of the potential difference generated by the up block. Therefore, when checking the laser diode emission,
charged electrostatic load, etc. on clothing and the human body. observe from more than 30 cm away from the objective lens.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the LASER DIODE AND FOCUS SEARCH OPERATION
repair parts. CHECK
The flexible board is easily damaged and should be handled with
care. Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output two times.
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH Note for installation (ROTARY ENCODER)
TURNS OFF
Note :
When attaching the Base unit, insert the
BU cam section A into the groove of BU cam.
Section A
groove
Note :
When attaching the BU
cam, engage the Rotary
encoder switch as shown in
the figure.
Insert a tapering driver into the

aperture of the unit bottom, and turn
in the direction of arrow.
* To close the disc tray, turn the
driver in the reverse direction.
[FL Display Tube, LED All Lit and Key Check mode] [Switching the channel step 9 KHz/10 KHz]
When the TUNER/BAND , DISPLAY , and MENU 2 buttons Press ENTER/NEXT button and POWER button simultaneously
are pressed simultaneously, the FL display tube and LEDs will all to switch the AM channel step 9 KHz and 10 KHz. Be sure not to
light up. Press any button to enter the key check mode. change with carelessness.
When the key check mode is entered, the FL display tube displays
“K 1 J0 V0”. Each time a button is pressed, the counter increases
in the following order, K 2 n K 3 n K 4.
If buttons already pressed once are pressed again, the counter will
not increase. When the VOLUME knob is rotated in the + direction,
the count increases in the following order.
V1 n V2 n V3.
When rotated in the–direction, it decreases in the following order.
V0 n V9 n V8.
When the AMS dial is rotated in the clockwise direction, the count
increases in the following order.
J1 n J2 n J3.
When rotated in the counterclockwise direction, it decreases in the
following order.
J0 n J9 n J8.
To exit form the test mode, press the TUNER/BAND , DISPLAY
, MENU 2 buttons simultaneously again.
—5—
SECTION 2 This section is extracted from
GENERAL instruction manual.
@ª ª / · (reverse side play /

Index to Parts and Controls front side play) button Rear Panel
#º p (stop) button
(AEP, UK, German, East European models)
Refer to the pages indicated in parentheses for #¡ Deck A
details on how to use the controls. #™ § EJECT button
Controls with an asterisk have indicators on #£ CD SYNCHRO button
themselves. #¢ r REC button
#∞ P PAUSE button
#§ Deck B
Front Panel 4
!™ 1
1 !£ 2
2 ^
!¢ MULTI FUNCTION CONTROL buttons 3
3 !∞
4 !§
The buttons you can operate the CD player,
5 !¶
tuner and the timer light up.
6 !•
7 !ª CD player
8 @º
9 ª · ª · @¡ 1 MD OUT / IN jacks
0 @™ 2 CD DIGITAL OUT OPTICAL jack
!¡ @£ 3 SPEAKER L / R connectors

@¢ CD CONTINUE SHUFFLE PROGRAM REPEAT 4 ANTENNA terminals
@∞ #£ Tuner (E, EA, Hong Kong, Malaysia, Singapore,

@§ #¢ Taiwan, Tourist, Thailand, Indonesian models)
@¶ #∞
@• @•
TUNING TUNER
TUNER STEREO MONO
MODE MEMORY

@ª ª · ª ·
@ª
#º #º
#¡ #§
Timer
#™ #™ 5
TIMER CLOCK SET SET SELECT SLEEP 1
2
1 Disc tray
2 POWER switch 3 6
3 LOOP button
4 TIMER button
5 PHONES jack 4
6 DISPLAY button
7 SURROUND button
8 MIX MIC jack 1 MD OUT / IN jacks
9 MULTI FUNCTION CONTROL buttons 2 CD DIGITAL OUT OPTICAL jack
0 FREQUENCY +/– buttons 3 SPEAKER L / R connectors
!¡ JOG dial 4 SUPER WOOFER jack
!™ MENU 1 – 3 button 5 ANTENNA terminals
!£ § OPEN / CLOSE button 6 Voltage selector (except for EA4, Thailand
!¢ fl (play / pause) button models)
!∞ p (stop) button
!§ P FILE button
!¶ EFFECT ON / OFF button • Abbreviation
!• TUNER / BAND button EA4: Without voltage selector Saudi Arabia model
!ª FUNCTION button
@º ENTER / NEXT button
@¡ GROOVE button
@™ DBFB button
@£ VOLUME control
@¢ KARAOKE PON / MPX button
@∞ HIGH SPEED DUBBING button
@§ DIRECTION button
@¶ DOLBY NR button
@• 0 / ) (rewind / fast forward) button
—6—
Display Window Remote (RM-SD50)
1 2 3 4 56789 0 !¡ 1
2
MPX DOLBY NR 1 2 3 4 5
12 REC SLEEP
PON B OFF RELAY
DBFB
6 7 8 9 10
0
SUR 12 TUNED MONO STEREO 11 12 13 14 15
ALL PROGRAM
1DISK S SHUFFLE 16 17 18 19 20
MANUAL
!¡
REPEAT 1 STEP
PRESET
3
AUTO
SYNC
REC
khz dB
Mhz MIN VOL
!™
4 – + !£
!™ !£ !¢
!¢
5
!∞
1 SUR indicators 6
!§
2 indicator 7
+ !¶
3 Timer indicators 8
4 Karaoke PON / MPX indicators –
5 DOLBY NR indicator 9 !•
6 Tuning indicator
7 Direction mode indicators
8 DBFB indicator

1 SLEEP button
9 CD playback indicators
0 Music calendar 2 LOOP button
!¡ VOLUME indicators 3 CD button
!™ Tuner indicators 4 TUNER / BAND button
!£ Multi display 5 DECK A / DECK B button
!¢ Radio frequency / playing time / sound 6 FUNCTION button
frequency level indications 7 / button
8 MUSIC MENU ON / OFF button
9 / button
0 POWER switch
!¡ (pause) button
!™ (stop) button
!£ – / + AMS* button
!¢ / (rewind / fast forward)
button
!∞ EDIT button
!§ CHECK button
!¶ CLEAR button
!• VOL (+ / –) button

* AMS=Auto Music Sensor

—7—
SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
3-1. FRONT PANEL

4 Two screws
(+BVTP2.6X8)
1 Remove the connectors

(MAIN board: CN402, CN702)
(HP board: CN513)
CN402
CN702
CN513
2 Two screws
(+BVTT3X8)
5 Remove the claws

(Three positions)
3 Two screws
(+BVTT3X8)
3-2. TC MECHANISM DECK
6 TC mechanism deck
5 Three screws
(+BVTP2.6X8)
3 Cassette holder
assembly (A), (B)
2 Remove the claws

(Four positions)
1 Push the EJECT button.

(Two positions)
4 Torsion spring
(L), (R)
—8—
3-3. HP BOARD, JOG BOARD AND PANEL BOARD
*Note: It will be easy to remove if you push

lightly from the hole of the JOG board
with some screwdrivers or etc.
Screw driver
3 Nut
4 Nut
2 Knob (JOG) * Note 1 Knob (VOL) * Note
.
5 Two screws !™ JOG board
(+BVTP2.6X8)
6 HP board
7 Six screws
8 Six screws (+BVTP2.6X8)
(+BVTP2.6X8)
!£ PANEL board
9 Two claws
!¡ Claw
0 Three claws
—9—
3-4. CD BLOCK
4 CD block
1 Remove the connectors (CD mechanism deck 3 Two screws
(MAIN board: CN201) and CD chassis) (+BVTP3X8)
(LOADING board: CN291)
CN291
2 PC board holder
CN201
3-5. CD MECHANISM DECK

1 Two screws
(+BVTP3X8)
3 Remove the CD mechanism

deck direction of arrow.
2 Two claws
— 10 —
SECTION 4 SECTION 5
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution DECK SECTION 0 dB=0.775V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head damagnetizer.
record/playback heads pinch rollers 2. Do not use a magnetized screwdriver for the adjustments.
erase head rubber belts 3. After the adjustments, apply suitable locking compound to the
capstan idlers parts adjusted.
2. Demagnetize the record/playback head with a head 4. The adjustments should be performed with the rated power supply
demagnetizer. voltage unless otherwise noted.
3. Do not use a magnetized screwdriver for the adjustments. 5. The adjustments should be performed in the order given in this
4. After the adjustments, apply suitable locking compound to the service manual. (As a general rule, playback circuit adjustment
parts adjusted. should be completed before performing recording circuit
5. The adjustments should be performed with the rated power adjustment.)
supply voltage unless otherwise noted. 6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise
Torque Measurement specified.
DOLBY NR switch: OFF
Torque Torque meter Meter reading
36 to 61 g • cm Tape Signal Used for
FWD CQ-102C
(0.5 - 0.84 oz • inch)
P-4-A100 10 kHz, –10 dB Azimuth Adjustment
FWD 2 to 6 g • cm
CQ-102C WS-48B 3 kHz, 0 dB Tape Speed Adjustment
back tension (0.02 - 0.08 oz • inch)
36 to 61 g • cm P-4-L300 315 Hz, 0 dB Level Adjustment
REV CQ-102RC
(0.5 - 0.84 oz • inch)
REV 2 to 6 g • cm Record/Playback Head Azimuth Adjustment
CQ-102RC
back tension (0.02 - 0.08 oz • inch) (Deck A, Deck B)
FF/REW 61 to 143 g • cm
CQ-201B
(0.85 - 1.99 oz • inch) Note: Perform this adjustments for both decks.
100 g or more
FWD tension CQ-403A
(3.53 oz or more)
100 g or more
REV tension CQ-403R
(3.53 oz or more)
test tape
P-4-A100 MAIN board
(10kHz, –10dB) CN403
Pin 3 (L-CH) level meter
Pin 1 (R-CH)
set +
–
MAIN board
CN403
Pin 2 (GND)
— 11 —
Procedure: Tape Speed Adjustment (Deck A)
1. Mode : Playback
2. Turn the adjustment screw and check output peaks. If the peaks Note: Start the Tape Speed adjustment as below after setting the
do not match for L-CH and R-CH, turn the adjustment screw so test mode.
that outputs match within 1 dB of peak. The tape speed can be changed with the HIGH SPEED
DUBBING button during the test mode.
Method :
1. Turn the power switch on.
2. Press the DISPLAY button, MENU 1 button and TUNER/
L-CH within 1dB
peak output BAND button simultaneously.
level within
1dB Procedure :
Mode: Playback
test tape WS-48B frequency counter
(3kHz, 0dB)
R-CH
peak set +
screw –
position
screw
L-CH R-CH position MAIN board
peak peak CN403 Pin 3 (L-CH)
Pin 1 (R-CH)
3. Mode: Playback
test tape 1. Insert the WS-48B into the deck A to playback.
P-4-A100 main board 2. Press the HIGH SPEED DUBBING button. Then at HIGH
(10kHz, –10dB) CN403 SPEED mode.
Pin 3 (L-CH) 3. Adjust the RV652 on the AUDIO board so that the frequency
oscilloscope
counter reading becomes 6,000 ± 90 Hz.
Pin 2 (GND)
L 4. Press the HIGH SPEED DUBBING button again to be set the
set NORMAL SPEED mode.
5. Set to the playback mode.
R
6. Adjust the RV651 on the AUDIO board so that the frequency
counter reading becomes 3,000 ± 90 Hz.
Pin 1 (R-CH) Frequency difference between deck A and deck B the beginning
of the tape should be within ± 1.5%.
Waveform of oscilloscope
Adjustment Location: AUDIO board
Playback Level Adjustment (Deck A, Deck B)

in phase 45˚ 90˚ 135˚ 180˚
good wrong Procedure:
Mode: Playback
4. After the adjustments, apply suitable locking compound to the test tape P-4-L300 level meter
parts adjusted. (315Hz, 0dB)
Adjustment Location: Playback Head (Deck A) set

Record/Playback/Erase Head (Deck B)
MAIN board
CN403 Pin 3 (L-CH)
Pin 1 (R-CH)
Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.
Adjustment level:
CN403 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
FWD side REV side level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
Adjustment screw
— 12 —
Record Bias Adjustment (Deck B) Record Level Adjustment (Deck B)
Procedure: Procedure:
1. Press FUNCTION button to Select MD. 1. Press FUNCTION button to Select MD.
2. Mode: Record 2. Mode: Record
MD IN
1) 315Hz
2) 10kHz
} 50 mV (–23.8 dB) MD IN
315Hz 50mV (–23.8 dB)
AF OSC AF OSC
blank tape blank tape
600 CS-123 600 CS-123
attenuator attenuator
set set
3. Mode: Playback 3. Mode: Playback

recorded recorded
level meter
position portion level meter
set set
MAIN board MAIN board

CN403 Pin 3 (L-CH) CN403 Pin 3 (L-CH)
Pin 1 (R-CH) Pin 1 (R-CH)
4. Confirm playback the signal recorded in step 2 become 4. Confirm playback the signal recorded in step 2 become
adjustment level as follows. adjustment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH) If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 2 and 3. and RV351 (R-CH) on the MAIN board to repeat steps 2 and 3.
Adjustment level: The playback output of 10 kHz level difference Adjustment level:
against 315 Hz reference should be ± 0.5 dB. CN403 PB level: 47.3 to 53.1 mV (–24.3 to –23.3 dB)
Adjustment Location: AUDIO board Adjustment Location: MAIN board
Adjustment Location:
[AUDIO BOARD] (Conductor Side) [MAIN BOARD] (Component Side)
RV341 (L CH), 441 (R CH)
Record Bias Adjustment
1 3
RV651 (Normal speed)
RV301 RV652 (High speed) RV651 RV652 CN403 RV351
RV401 RV341 Tape Speed Adjustment IC401
RV441 RV351
RV311
RV301 (L CH), 401(R CH) Record Level Adjustment
RV301
Playback Level Adjustment RV411 (R CH)
(Deck B)
RV311 (L CH), 411 (R CH) RV301
Playback Level Adjustment Record Level Adjustment
(Deck A) (L CH)
— 13 —
TUNER SECTION 0dB=1µV
Note: 1. As a front-end (FE1) is difficult to repair if faulty, replace

it with new one.
2. No adjustment is needed due to a tuner pack.
AM Tuned Level Adjustment

Note: FM Tuned Level adjustment should be performed after this
AM Tuned Level Adjustment.
Setting:
Band: AM or MW
loop antenna
loop antenna (Supplied accessories)
AM RF SSG
set
AM antenna
30% amplitude 60cm terminal (TM1)
modulation by
Field strength dB (µV/m) = SSG output level dB (µV/m) –26dB.
400Hz signal
Modulation: 999 kHz (at 9 kHz step)
1,050 kHz (at 10 kHz step)
Procedure: Adjustment Location:

1. Set the output of SSG so that the input level of the set becomes [TCB BOARD] (Component Side)
55 dB.
2. Tune the set to 999 kHz or 1,050 kHz.
3. Adjust RV41 to the point (moment) when the TUNED indicator RV41
RV41
will change from going off to going on.
AM Tuned Level
Adjustment
Adjustment Location: TCB board
FM Tuned Level Adjustment

Note: This adjustment should be after AM Tuned Level Adjustment.
RV42 IC41 TM1
Setting:
Band: FM RV42
FM Tuned Level
FM RF stereo signal Adjustment
generator
75 Ω coaxial FE1
set
Carrier frequency : 98MHz
Modulation : AUDIO 1kHz, 75kHz FM ANTENNA terminal
deviation (100%) (TM1)
Output level : 25dB (at 75 Ω open)
Procedure:
1. Supply a 25 dB 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. Adjust RV42 to the point (moment) when the TUNED indicator
will change from going off to going on.
Adjustment Location: TCB board
— 14 —
SW OSC Voltage Adjustment Adjustment Location:
(Tourist model)
[TCB BOARD] — Component Side —
Setting:
Band: SW
Procedure: D1, CV2, T2

SW OSC Voltage
1. Connect digital Voltmeter to diode D1 center lead and ground.
Adjustment
2. Adjust for a following value reading on digital voltmeter.
CV2 CV1
IC41 D1
Adjustment Reading on digital
Set frequency TM1
part voltmeter
T2 T1
5.95 MHz T2 1.2 ± 0.1 V
SW CV1, T1
17.9 MHz CV2 8.5 ± 0.2 V SW Tracking
Adjustment
SW Tracking Adjustment
(Tourist model)
Setting:
Band: SW
AM RF SSG level meter
set
30% amplitude SPEAKER terminal

modulation by
AM ANTENNA terminal
400Hz signal
Procedure:
Adjust for maximum reading on level meter.
Set frequency Adjustment

part
7 MHz T1
SW
17 MHz CV1
• Repeat the procedures is each adjustment several times, and the

frequency coverage and tracking adjustment should be finally done
by the trimmer capacitors.
— 15 —
S Curve Check
CD SECTION
Procedure :
Note: oscilloscope
1. CD Block is basically designed to operate without adjustment. BD board
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (FEO)
3. Use an oscilloscope with more than 10MΩ impedance. TP (VC)
4. Clean the object lens by an applicator with neutral detergent when
the signal level is low than specified value with the following
1. Connect oscilloscope to test point TP (FEO).
checks.
2. Connect between test point TP (FOK) and Ground by lead wire.
5. Adjust the focus bias adjustment when optical block is replaced.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
Focus Bias Adjustment
actuate the focus search. (actuate the focus search when disc
oscilloscope table is moving in and out.)
BD board 5. Check the oscilloscope waveform (S-curve) is symmetrical
between A and B. And confirm peak to peak level within 2.4 ±
TP (RF) 0.7 Vp-p.
TP (VC)
S-curve waveform
symmetry
Procedure:
1. Connect oscilloscope to test point TP (RF).
(Ground terminal : TP (VC))
A
2. Turned Power switch on.
within 2.4 ± 0.7 Vp-p
3. Put disc (YEDS-18) in and playback.
4. Adjust RV101 so that the waveform is clear. B
(Clear RF signal waveform means that the shape “ ” can be
clearly distinguished at the center of the waveform.)
5. After adjustment, check the RF signal level.
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
• RF signal
A : B or B : A is more than 10 : 7.
VOLT/DIV: 200 mV
• Take sweep time as long as possible and light up the
TIME/DIV: 500 nS
brightness to obtain best waveform.
RF Level Check
level: 1.3 ± 0.3 Vp-p
Procedure :
oscilloscope
BD board
TP (RF)
TP (VC)
1.Connect oscilloscope to test point TP (RF) on BD board.

2.Turned Power switch on.
3.Put disc (YEDS-18) in and playback.
4.Confirm that oscilloscope waveform is clear and check RF signal
level is correct or not.
Note: Clear RF signal waveform means that the shape “ ” can be
clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 nS
level: 1.3 ± 0.3 Vp-p
— 16 —
E-F Balance Check Adjustment Location:
oscilloscope [BD BOARD] — Component Side —

BD board
RF
FOK
TP (TEO)
TP (VC) RV101
IC102
IC101
Procedure: TEI
1. Connect test point TP703 (ADJ2) on MAIN board to Ground RV103
with a lead wire. FEO FEI
2. Connect oscilloscpe to test point TP (TEO). TEO
3. Turned Power switch on. RV102
4. Put disc (YEDS-18) in and playback. VC
5. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0Vdc, and check this level.
Traverse waveform
IC104
A PCK
0V
B GND
level: 300 ± 100 mVp-p [MAIN BOARD] — Conductor Side —

Specified level: • A – B x 100 = less than ± 7%
2 (A + B)
• A + B = 300 ± 100 mVp-p
6. Remove the lead wire connected in step 1.
Focus/Tracking Gain Adjustment (RV102, RV103)
This gain has a margin, so even if it is slightly off.

There is no problem.
Therfore, do not perform this adjustment.
Please note that it should be fixed to mechanical center position
when you moved and do not know original position.
IC701
TP703
(ADJ2)
— 17 —
HCD-GR5/RX50
SECTION 6
DIAGRAMS
6-1 BLOCK DIAGRAMS
- CD SECTION -
OPTICAL PICK-UP BLOCK CD X101

3 IC200 DIGITAL OUT 16.9344MHz
IC101 (1/2)
OPTICAL
FOCUS/TRACKING SERVO IC104
B+
DETECTOR K EFM COMPARATOR DIGITAL FILTER
D/A CONVERTER
E 39 5•6
XTI
XTO
DOUT
1 35 RF1 RFO 31 14 RF
A
4
C,OUT 23 55 CNIN XTAI 34 4 CKO
A D 2 36 PD2
D SENS 24 54 SEIN IC103
5 PCMD 21 2 DATA
FOK 25 1 FOK DIGITAL SIGNAL
B C 10 38 F PROCESSOR LRCK 20 1 LRCK
C DATA 21 56 DATAO
6 39 E CLV SERVO BCLK 22 3 BCLK L-CH
XLT 20 57 XLTO
B CLK 19 59 CLKO L OUT 16
RV102
R OUT 13
F FOCUS R-CH
GAIN
CLOCK
CLOCK
RV101
MLAT
SCOR
XRST
DATA
SQCK
SQS0
SENS
DATA
XLAT
MDP
2 FE1 FOCUS
BIAS
3 51 52 53 43 46 47 49 50 26 28 27
1 FEO
FE BIAS 37 B+
42 TEO
44 TEI
RV103 FE-O 6
CD CLK
TRACKING FE-M 7
GAIN CD DATA
TA-M 12 DF LAT
TA-O 13 SCOR
Q101,102 33 LD
LD DRIVE SQ DATA
SQ CLK
LASER 34 PHD SENS
XRST
DIODE Q103
FGD 4 FOCUS SW
FOCUS SW
25
C
XRST MAIN
SECTION
XLAT
(page 19)
FOCUS TRACKING 7
COIL COIL
XRESET
T-
18 TRACKING
COIL DRIVE 19
17
S291 LOAD OUT
OUT SW
T+ FOCUS / TRAKING S292 LOAD IN
COIL DRIVE IN SW
IC102 (1 / 2 )
2-AXIS
DEVICE
F-
12 FOCUS
F+ COIL DRIVE 9
11
IC201
LOADING MOTOR DRIVER
SLED / SPINDLE 2 OUT1 IN1 5 LOAD IN

SLED
MOTOR DRIVE
IC102 (2 / 2) SERVO M
IC101 (2 / 2) 10 OUT2 IN2 6 LOAD OUT
M903
LOADING MOTOR
M102 26
SLED MOTOR M . SLED MOTOR
DRIVE
25 16 SLO SL+ 14
27
M101 1.
SPINDLE MOTOR M 2
SPINDLE MOTOR 4
DRIVE
• R CH:Same as L CH
• SIGNAL PATH
:CD
:digidal out
— 18 —
HCD-GR5/RX50
— MAIN SECTION —
IC601
MIC AMP EXCEPT AEP,UK,G,EE
J601
3 1 6 7 J201
MIX
MIC SUPER
R-CH WOOFER
R-CH +
J801 IC802 INPUT SELECTOR IC1201

MD POWER AMP TM1201
(AUDIO) v
1 RY1201 SPEAKER
IN TC
2 65 64 +
L ST 3 71 45 44 43 42 38 1 10 +
4 –
Q1207
CD
5 B 9 29 +B -
MICON EQ Q1201 RELAY DRIVE
A 10 28 Q954
INTERFACE OVER LOAD J501
IC901 MUTE R-CH
INH 6 30 DET 6 PHONES
BB12
BB22
EQUALIZER/VOLUME
+ 2 IC1202 R-CH
32 33 34 62 40 41 Q820 R-CH + 1 PROTECTOR Q1208
MUTE HP/SP
DA
CK
SWITCH Q1204 7 4 SWITCHING
PB L Q901 Q902
REC L DBFB FEED +
SWITCH BACK
Q1205
R-CH PROTECTOR
SWITCH
62
62427 LAT
PLAY REC/PB 55 TC RELAY POWER ON 67
A SHUT 56 A SHUT
B SHUT 57 B SHUT DBFB HIGH 77 Q1206
STANDBY
B HALF 58 B HALF MUTE 70 SWITCH
A HALF 59 A HALF
A PLAY 60 220 A PLAY
B PLAY 61 220 B PLAY
PB A/B 80 TC A
NORM/HIGH 81 NORM GM REQ 34 13 REQ GM LED1 43
BIAS ON/OFF 82 BIAS OFF MG CLK 35 14 CLK MG |
Q504
B LED4 40 Q502,503
RM ON/OFF 83 REC MUTE GM DATA 36 15 DATA GM • • Q507-511 D579,583
DECK NR ON/OFF 84 NR OFF LED9 10 Q601-603 D585-590 D +5V
MG DATA 37 16 DATA MG •
SECTION 9 LED D601,611,621
REC/PB 85 PB MG RDY 32 46 RDY MG •
(Page 23) DRIVE
PAS/DOL 86 PASS AMP/DOLBY 51
|
LM ON/OFF 87 LINE MUTE ON
LED13 49
CAP M H/L 88 CAP M HIGH RESET 4
A TRG 89 A TRG
Q501 D1016,1017
B TRG 90 B TRG Q701 LED SELECT 19 LED D1021,1022
TRIG H/L 91 TRG LOW RESET CONTROL TC +5V
CAP M ON/OFF 92 CAP M ON SWITCH D1309,1310
ST L IC1003 RECT
DA +7.5V
COM DATA 73 COM DATA AC CUT 8 17 RESET +7V REG
CK IC502
COM CLK 71 COM CLK
IC702 REMOTE IC1002
COM DIN 72 COM DIN SIRCS IN 47 CONTROL +7.5V
RESET +7V REG T1601
A STEREO 93 STEREO IC701 RECEIVER D1097
MASTER CONTROL POWER TRANSFORMER
TUNER TUNED 94 TUNED IC1001 | AC -IN
D705 IC501 +5.6V
SECTION S562 +5V REG D1099 D1003
ST CE 95 ST CE GRAPHIC D704
(*) +5.6V RECT |
MUTE 10 ST MUTE ON CONTROL MULTI JOG +5V
STATION D1006
D706 RECT
IC1004
+5V -7.5V
XOUT 2 34 X1 JOG A 45 ROTARY -7V REG
X701 X501 JOG B 31 ENCODER D1018 VS1601
10MHz 5MHz Q1003 D1001 VOLTAGE
L CH D +5V ST +10V
XIN 3 35 X2 KEY4 28 +10V REG RECT SELECTOR
| | KEY
SCOR 25 SCOR
KEY1 25 MATRIX EXCEPT AEP,UK,G,EE,EA4,TH
XOUT 5 Q1001,1002 D1013

DF LAT 29 DF LAT Q1006
D +5V CD POWER VF DP D1014
SENS 30 SENS X702 -25V REG
(CD) ON/OFF RECT
X RST 31 XRST 32kHz S561
XIN 6 VOLUME
CD CLK 38 CD CLK +B
C D1250
CD DATA 40 CD DATA VOL A 44 ROTARY -B RECT
CD ENCODER
FOCUS SW 43 FOCUS SW VOL B 12
SECTION
(Page 18) SQ CLK 44 SQ CLK
GR1-12 SEG1-22 VF
SQ DATA 45 SQ DATA
7 - 1 • 80 - 76 75 - 72 • 70 - 53
X LAT 46 X LAT • R CH:Same as L CH • Abbreviation
• SIGNAL PATH G : German model.
OUT SW 20 OUT-SW-OPEN EE : East European model.
FL501 : FM EA4 : Without voltage selector Saudi Arabia model.
IN SW 16 IN SW VF
FLUORESCENT INDICATOR TUBE TH : Thailand model.
: PB JE : Tourist model.
LOAD IN 21 LOAD IN
: REC
LOAD OUT 22 LOAD OUT
CD POWER 68 : CD
* AEP,UK,G,EE MODEL : (Page 21)
JE MODEL : (Page 22) : MD
– 19 – – 20 –
HCD-GR5/RX50
— TUNER SECTION — — TUNER SECTION — (Tourist MODEL)

(AEP,UK,German,East European MODEL)
ST +10V ST +10V
AEP,UK,G MODEL
OUT L 20 LPF 18 AMP IN L
Q5 AMP OUT L 16
Q5 CF2 TM1
TM1 AM / FM 24 22 MPX IN FE1 AM / FM 24 22 MPX IN
FE1 10.7MHz AMP OUT L 16 ANTENNA CF1
ANTENNA FM FRONT END CF1 CF3 FM FRONT END CF3
OUT R 21 RCH 10.7MHz
10.7MHz
IF AMP IF AMP 10.7MHz IF AMP IF AMP 10.7MHz OUT L 20 LPF 18 AMP IN L
FM 75Ω 1 FM IN FM 75Ω ANT IN IF OUT 1 FM IN
ANT IN IF OUT Q1,2 Q3,4
COAXIAL Q1,2 Q3,4
F OUT
F OUT
VT
OUT R 21 RCH
VT
AM
FM / AM MPX FM / AM MPX
EE MODEL AM IC41
IC41 ST L
ST L
SW OSC
SW TRACKING VOLTAGE
AEP,UK,EE MODEL FE2
MW / LW FRONTEND
T1 CV1 CV2 T2 STEREO
STEREO STEREO 8
6 12 4 REG STEREO 8 4 REG
LW SW TUNED MW SWITCH TUNED
TUNED 7 D1 TUNED 7
Q9 Q9
5 13 Q8 AM IF
AM IF AM MIX 2 5 AM IF
AM MIX 2 5 AM IF IFT41
IFT41 2 FE2
3 14
MW FRONTEND 10
15 G
MODEL AM 7 AM
16 SD 12 3 SD 12
2 RV41 RV41
AM 9 29 AM OSC
17 29 AM OSC AM
TUNED
TUNED
LEVEL
13 4 12 11 14 5 15 LEVEL
26 25 24 23 22 21 20
9 DET 27 AM RF IN
G MODEL 27 AM RF IN
X41 9 DET
10.7MHz X41
Q14
Q14 AM 13 SW 10.7MHz
LW SW SD SWITCH AM 13
X42 SD
450KHz X42
VCO STOP
450KHz
Q12
AM / FM
Q12 23 VCO Q10

IF BUFF
Q11
FM SD
Q13
VCO STOP
MUTE
Q13 MW SW X43 MW SW 23 VCO
AM / FM
MW SW MW
IF BUFF
MW SW
FM SD
SWITCH
MUTE
456KHz SWITCH X43
SWITCH
30 14 15 11 456KHz
30 14 15 11
AEP,UK,EE MODEL
RV42 MUTE MUTE

A A
FM MAIN MAIN
TUNING SECTION SECTION
LEVEL (page 19) RV42 (Page 19)
FM
TUNED
LEVEL
X21 X21
4.5MHz 4.5MHz
10 15 19 9 11 14 7 2 12 8 1 24 10 15 19 9 11 14 7 2 12 8 1 24
ST-CE ST-CE
X OUT
FM
X IN
PD1
MW
FM/AM IF
FM OSC
VCO STOP
X OUT
MW
AM OSC
FM
X IN
IF REQ
PD1
FM OSC
VCO STOP
FM / AM IF
FM
MW
MW
AM OSC
IF REQ
FM
CE 3 CE 3
COM-DIN COM-DIN
DI 4 DI 4
PLL PLL
IC21 COM-CLK IC21 COM-CLK
CL 5 CL 5
COM-DATA COM-DATA
DO 6 DO 6
• R CH :Same as L CH Abbreviation • R CH:Same as L CH

• SIGNAL PATH G :German model • SIGNAL PATH
:FM EE :East European model :FM
:MW :AM
:LW :SW
– 21 – – 22 –
HCD-GR5/RX50
— DECK SECTION — 6-2. CIRCUIT BOARDS LOCATION

TCB board
(AED, UK, G, EE, JE)
PB A/B
CN403 TRANSFORMER board FM/AM TUNER ENCAPSULATED COMPONENT
S1004 S1008 (EXCEPT AEP,UK,G,EE,JE)
A CrO2 B CrO2
R-CH
RV311 14 4 5 15 17
IC611 PLAYBACK
A/B
ABO
CIN
A 120/70 B 120/70
LEVEL
L DECK A 70 PAS/DOL
HP101 A IN PAS 24 PAS/DOL PANEL board
2 PB OUT
PB HEAD B IN 8 PB L
(DECK A) R-CH 3 120
R DOL Q301
RV301 LM ON/OFF
IC601 MUTE
PLAYBACK DOLBY NR
LEVEL IC401 NORM/
Q402 MAIN board
L DECK B HEADAMP HIGH 16 NORM/HIGH
REC/PB HEAD
(DECK B)
NR ON/
20 NR ON/OFF
HP board
OFF
R R-CH EQ OUT
13 21 REC/PB
PB
DOLBY
REC IN
TYPE B 6 REC L
BIAS ON/OFF
REC OUT
BIAS SW 18 BIAS ON/OFF
B OUT
EQ IN
RM ON/OFF 19 RM ON/OFF
11 10 27
HRPE101
3 1 RV301
IC602 REC LEVEL
JOG board • Abbreviation
P R
4 RELAY REC/PB G : German model.
REC/PB RV341
EE : East European model.
REC BIAS +7.5V JE : Tourist model.
CURRENT Q623,Q401
Q403,407 CAP M ON/OFF
CAP M SWITCH
REC BIAS
ERASE BIAS
T621,Q621,622 Q651
Note: pA is including in AUDIO board.
M1
BIAS OSC Q406
ERASE HEAD X CAPSTAN M SPEED
SWITCH
CAP M H/L
MOTOR CONTROL BD board
B
MAIN
RV651 RV652 SECTION
NORMAL HIGH (Page 19)
SPEED SPEED
Q1001
REEL A SHUT
DETECT
Q1002
REEL B SHUT
DETECT
• R CH:Same as L CH S1001 (A PLAY)

• SIGNAL PATH LOADING board
+5V A PLAY
:PB (DECK A) S1002 (B PLAY) pA
:PB (DECK B) B PLAY MOTOR board
S1003 A HALF
:REC (DECK B)
(A HALF)
+5v
S1005
(REC A)
S1006
(B HALF) B HALF
S1009 LEAF SWITCH board

(REC B)
AUDIO board (including p A)

Q408-410
VZ 4 TRIG H/L
SWITCH
2 OUT1 IC402
M2
TRIGGER Q412
TRIGGEER M MOTOR
IN2 6
SWITCH
B TRIG
MOTOR
10 OUT2 DRIVE Q411
IN1 5 A TRIG
SWITCH
– 23 – – 24 –
6-14. IC PIN FUNCTIONS
• IC501 GRAPHIC CONTROL (µPD78042FGF-027-3B9)
Pin No. Pin Name I/O Function

1 to 7 GR7 to 1 O Fluorescent indicator tube grid signal output.
8 VDD – +5V
9, 10 LED9, 10 O LED drive signal output
11 KEY SELECT O Not used. (Open)
12 VOL IN B I Volume encoder signal input.
13 REQ GM I/O Request signal from/to master control.
14 CLK MG I Serial clock input.
15 DATA GM O Serial data output to master control.
16 DATA MG I Serial data input from master control.
17 RESET I Reset signal input.
18 PANEL SW I CD door open detection input. (Not used) (Open)
19 LED SELECT O LED select signal output.
20 AVSS – Ground
21 to 24 SPEANA IN1 to 4 I Spectram analizer signal input. (Connected to ground)
25 to 28 KEY IN1 to 4 I Key matrix input.
29 AVDD –
+5V
30 AVREF –
31 JOG IN B I Jog dial encoder signal input.
32 XT2 I Not used. (Open)
33 VSS – Ground
34 X1 I
X’tal (5 MHz).
35 X2 O
36 to 39 LED8 to 5 O LED drive signal output. (Not used) (Open)
40, 41 LED4,3 O
LED drive signal output.
42, 43 LED2,1 O
44 VOL IN A I Volume encoder signal input.
45 JOG IN A I Jog dial encoder signal input.
46 RDY MG I Ready signal from master contorl.
47 SIRCS IN I SIRCS signal input.
48 IC (VPP) – Ground
49, 50 LED12, 13 O
LED drive signal output.
51 LED11 O
52 VDD – +5V
53 to 70 SEG22 to 5 O Fluorescent indicator tube segment signal output.
71 V. LOAD – –25V for Fluorescent indicator tube.
72 to 75 SEG4 to 1 O Fluorescent indicator tube segment signal output.
76 to 80 GR12 to 8 O Fluorescent indicator tube grid signal output.
— 61 —
• IC701 MASTER CONTROL (TMP87CP64YF-6521)
1 VSS – Ground
2 XOUT O
X’tal (10 MHz).
3 XIN I
4 RESET I Reset signal input.
5 XOUT O
X’tal for clock (32.768 KHz).
6 XIN I
7 GND (test) – Ground
8 AC CUT I Back up signal input.
9 SUPER WOOFER ON O Not used. (Connected to ground)
10 ST-MUTE ON O Mute signal output for tuner.
11 180-A-PLAY I
12 180-B-PLAY I Tape detection signal input. (Not used) (Connected to ground)
13 180-B-REC I
14 CLK CHK I Not used. (Pull up)
15 UP-SW I Disc table up detect. (Not used) (Connected to ground)
16 IN-SW I Loading in detection signal input.
17 ENCODER-0 I
18 ENCODER-1 I Disctray address detect encoder input. (Not used) (Connected to ground)
19 ENCODER-2 I
20 OUT SW OPEN I Loading out detection signal input.
21 LOAD IN O
Loading motor control signal output.
22 LOAD OUT O
23 TBL-L O
Table motor control signal output. (Not used) (Open)
24 TBL-R O
25 SCOR I Sub-code sync signal input.
26 TBL-SENS I CD Table sensor signal input. (Not used) (Connected to ground)
27 RDS INT I RDS data start input. (Not used) (Connected to ground)
28 RDS DATA O RDS data start output. (Not used) (Connected to ground)
29 DF LAT O Latch signal for digital filter.
30 SENS I Table sence signal input.
31 XRST O Reset signal output for CD.
32 MG-RDY O Ready signal to graphic control.
33 ADJ I Test mode input.
34 GM-REQ I Request signal from graphic control.
35 MG-CLK O Clock signal to graphic control.
36 GM-DATA I Data input from graphic control.
37 MG-DATA O Data output to graphic control.
38 CD-CLK O Clock output. Serial bus line.
39 ADJ-2 I Test mode input.
40 CD-DATA O Data output. Serial bus line.
— 62 —
41 AUB IN I
Audio bus in/output. (Not used) (Open)
42 AUB OUT O
43 FOCUS SW O Focus switching signal output.
44 SQ-CLK O Subcode Q data read clock output.
45 SQ-DATA I Subcode Q data input.
46 X-LAT O Latch signal digital signal processor.
47 TEST I Test land.
48 VAREF I Analog reference voltage input.
49 VASS –
Ground
50 VSS –
51 VDD – +5V
52 SPEC I
Destination detection setting input.
53 DESTINATION I
54 DISC SENS I Not used. (Connected to ground)
55 TC RELAY O REC/PB select signal output.
56 A-SHUT I
57 B-SHUT I
58 B-HALF I
Control signal input from deck.
59 A-HALF I
60 220-A-PLAY I
61 220-B-PLAY I
62 62427 LAT O PLL latch output.
63 K-CON-LAT O Not used. (Open)
64 VOL LAT (AV) O Latch signal for electrical volume. (Not used) (Open)
65 REAR SP RELAY B O
Not used. (Open)
66 FRONT SP RELAY C O
67 POWER ON O Power on signal output.
68 CD POWER O CD power control signal output.
69 PROLOG LAT O Not used. (Open)
70 MUTE O Mute signal for AMP.
71 COM CLK O PLL clock output.
72 COM DIN I PLL data input.
73 COM DATA O PLL data output.
74 K CON ON O Not used. (Open)
75 LIDDED LED O Disc No. LED drive signal output. (Not used) (Open)
76 PROLOG ON O PRO LOGIC control output. (Not used) (Open)
77 DBFB-HIGH O DBFB switching signal output.
78 URG STB STDBY I Not used. (Pull-down)
79 URG STB ON O Not used (Open)
80 TC A O Deck A, B select output.
— 63 —
81 NORM O NORMAL/HIGH control signal output.
82 BIAS OFF O Bias oscillation output.
83 REC MUTE O Mute output.
84 NR OFF O Dolby ON/OFF signal output.
85 PB O REC/PB control signal output.
86 PASS. AMP/DOLBY O Dolby switching signal output.
87 LINE MUTE ON O Mute signal output for deck.
88 CAP. M-HIGH O Capstan motor control signal output.
89 A-TRG O
Trigger motor control signal output.
90 B-TRG O
91 TRG LOW O Trigger motor high/low contorol signal output.
92 CAP M ON O Capstan motor ON/OFF control signal output.
93 STEREO I Stereo dection signal from tuner.
94 TUNED I Tuned detection signal from tuner.
95 ST-CE O Latch signal output for tuner.
96 DELAY SEL MIC O
97 DELAY ON O
Not used. (Connected to ground)
98 DELAY LEVEL A O
99 DELAY LEVEL B O
100 VDD – +5V
— 64 —
6-15. IC BLOCK DIAGRAMS
- BD BOARD Section -
IC101 CXA1782BQ
RF M
PHD2
PHD1
RF O
RF I
PHD
CC1
CC2
FOK
LD
CP
CB
36 35 34 33 32 31 30 29 28 27 26 25
+
–
–
+
–
+
+
+
–
+
–
–
APC LEVELS
+
–
+ +
–
+ 24 SENS
–
IIL
–
FOK
–
MIRR
+
RF IV AMP1 DFCT
TTL 23 C. OUT
– 22 XRST
+
TTL
RF IV AMP2 21 DATA
FE BIAS 37 TTL • IIL DATA RESISTOR • INPUT SHIFT RESISTOR
• ADDRESS DECODER 20 XLT
+ IIL
–
FE AMP
IIL • OUTPUT DECODER 19 CLK
F 38 –
+
–
F IV AMP TOG1-3 FS1-4 TG1-2 TM1-7 PS1-4
+
BAL1-3
18 VCC
E 39 – FZC COMP
+
+
–
E IV AMP + +
–
EI 40
TE AMP
–
BAL1
BAL2
BAL3
• TRACKING
• ISET 17 ISET
• PHASE
HPF COMP LPF COMP
COMPENSATION
VEE 41
– TM6
TEO 42 TG1
–
+
+ 16 SL 0
TM5
TOG1
TOG2
TOG3
+
TM4 15 SL M
–
TZC COMP • FCS PHASE
LPFI 43 COMPENSATION
TM3 TM2 14 SL P
TEI 44
DFCT
ATSC 45 • WINDOW COMP FS1
TM1
+
TM7
ATSC 13 TA O
TZC 46 FS2 –
TDFCT 47
DFCT
TG2
+
• F SET
–
–
VC 48 FS4
+
1 2 3 4 5 6 7 8 9 10 11 12
FEO
FEI
FDFCT
FGD
FLB
FE O
FE M
SRCH
TGU
TG2
FSET
TA M
— 65 —
-BD BOARD Section -
IC102 BA6397FP
DRIVE
BUFFER
OUT1A 1 28 GND
DRIVE
BUFFER
OUT1B 2 27 OUT4A
DRIVE LEVEL
BUFFER SHIFT
IN1A 3 THERMAL 26 OUT4B
SHUT DOWN
LEVEL DRIVE
SHIFT BUFFER
IN1B 4 25 IN4A
TR-B 5 24 IN4B
REG 0 6 23 VC
XRST 7 REGULATOR 22 VCC

VCC
VCC
GND 8 21 VCC
IN2A 9 20 IN3B
DRIVER MUTE
IN2B 10 19 IN3A
DRIVE LEVEL LEVEL DRIVE
BUFFER SHIFT SHIFT BUFFER
OUT2A 11 18 OUT3B
OUT2B 12 17 OUT3A
DRIVE DRIVE
BUFFER BUFFER
GND 13 16 OP+
OP-OUT 14 15 OP–
— 66 —
- BD BORD Section -
IC103 CXD2507AQ
SPOD
SPOC
SPOB
SPOA
XLON
CLOK
CLKO
DATO
XLTO
CNIN
XLAT
SEIN
VDD
64 63 62 61 60 59 58 57 56 55 54 53 52
1
SERVO AUTO 51 DATA
FOK SEQUENCER 5
MON 2 50 XRST
MDP 3 CPU SUB CODE 49 SENS
MDS 4 14 INTERFACE PROCESSOR 48 MUTE
DIGITAL 47 SQCK
LOCK 5
4 CLV
TEST 6 46 SQSO
FILO 7 45 EXCK
DIGITAL EFM
FILI 8 PLL 44 SBSO
DEMODULATOR
PCO 9 43 SCOR
VSS 10 42 VSS
AVSS 11 ASYMMETRY 3 41 WFCK
CORRECTOR 40 EMPH
CLTV 12
D/A DIGITAL 39 DOUT
AVDD 13 5
INTERFACE OUT
RF 14 38 C4M
GENERATOR
6
BIAS 15 37 FSTT
CLOCK
16K ERROR 36 XTSL

ASYI 16
RAM CORRECTOR
ASYO 17 35 XTAO
3
ASYE 18 34 XTAI
WDCK 19 33 MNTO
20 21 22 23 24 25 26 27 28 29 30 31 32
LRCK
PCMD
BCLK
GTOP
XUGF
XPCK
VDD
GFS
RFCK
CZPO
XROF
MNT3
MNT1
IC104 PCM1710U-B
LRCIN 1 28 ML/DSD
INPUT DIGITAL MODE

DIN 2 INTERFACE FILTER CONTROL 27 MC/DM2
BCKIN 3 26 MD/DM1
CLKO 4 TIMING 25 MUTE

CONTROL
XTI 5 24 MODE
XTO 6 23 CKSL
NOISE
SHAPER
DGND 7 22 DGND
VDD 8 21 VDD
5-LEVEL DAC 5-LEVEL DAC
RIGHT LEFT
VCC2R 9 20 VCC2L
GND2R 10 LOW-PASS FILTER LOW-PASS FILTER 19 GND2L

RIGHT LEFT
EXT1R 11 18 EXT1L
3-STAGE AMP 3-STAGE AMP

EXT2R 12 17 EXT2L
RIGHT LEFT
VOUTR 13 16 VOUTL
GND1 14 15 VCC1
— 67 —
- TCB BOARD Section -
IC21 LC72130
XOUT VSS AOUT2 AIN2 PD2 PD1 AIN1 AOUT1 VDD FMIN AMIN IO2
24 23 22 21 20 19 18 17 16 15 14 13
PHASE DETECTOR
CHARGE PUMP POWER
ON
UNLOCK RESET 1/2
DETECTOR
SWALLOW COUNTER
REFERENCE 1/16. 1/17 4bits
DIVIDER
12bits PROGRAMMABLE
DRIVER
C'B DATA SHIFT REGISTER UNIVERSAL

I/F LATCH COUNTER
1 2 3 4 5 6 7 8 9 10 11 12
XIN BO5 CE DI CL DO BO1 BO2 BO3 BO4 IO1 IFIN
IC41 LA1835
AM-RF-IN
AMP-IN R
AMP-IN L
AM. CUT
AM-OSC
FM-AFC
MPX-IN
AM/FM
FM-SD
OUT R
OUT L
VCO
AGC
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ALC AM AM AM DECODER
OSC MIX RF. AMP ANTI BIRDIE
BUFF
STEREO
AGC SW
S METER STEREO
DRIVER
TRIG
AM AM MUTE
IF DET FF FF FF
LEVEL AM/FM
COMP VCO
DET IF
S-CURVE BUFF PILOT
AM/FM DET
TUNING
SW
FM DRIVE PHASE
FM AM
IF DET DET
FM
REG GND
Vcc
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FM-IN
AM-MIX
IF
REG
AM-IF
GND
TU-LED
ST-LED
DET
VCC
IF-BUFF
AM. SD
AM. SD
AM/FM
VCO-STOP
— 68 —
- AUDIO BOARD Section -
IC602 uPC1330HA
INVERTER
COMPARATER
1 2 3 4 5 6 7 8 9
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2
IC901 M62427FP
VOL OUT2
KEY OUT2
VOL IN2
REC 2A
REC 2B
REC 2C
F OUT2
F1 IN2
F2 IN2
F3 IN2
F4 IN2
BBIN2
F1 O2
F2 O2
F3 O2
F4 O2
F1 F2
F2 F2
F3 F2
F4 F2
F5 F2
BB12
NC7
NC6
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
KEY IN2 65 SBAND GRAPHIC EQUALIZER 40 BB22

–
BPF OUT 66 + 39 BUF IN1
+
–
BPF IN 67 38 BUF OUT1
NC8 68 37 NC5
–
+
IN 2B 69 + 36 AVDD
+ +
–
NC9 70 – – 35 DGND
IN 2A 71 – 34 LATCH
U-CON
+
AVSS 72 – – INTER 33 DATA
+ + FACE
AGND 73 32 CLOCK
IN 1A 74 31 DVDD
NC1 75 – – 30 PORT C
+ +
+
IN 1B 76 – 29 PORT B
+
–
NC2 77 28 PORT A
DELAY IN 78 – 27 BUFOUT1
+
– +
DELAY OUT 79 26 BUFIN1
KEY IN1 80 SBAND GRAPHIC EQUALIZER 25 BB21
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
REC 1A
REC 1C
KEY OUT1
NC3
REC 1B
NC4
F1 F1
F1 O1
F2 F1
F2 O1
F2 IN1
F3 F1
F3 O1
F3 IN1
F4 F1
F4 O1
F4 IN1
F5 F1
F OUT1
VOL IN1
VOL OUT1
BBIN1
F1 IN1
BB11
— 69 —
- MAIN BOARD Section -
IC201,402 LB1641
T.S.D O.C.P
MOTOR MOTOR
DRIVE DRIVE
FWD/REV/STOP
CONTROL LOGIC
1 2 3 4 5 6 7 8 9 10
FILTER
MOTOR
GND
FILTER
CLAMP
FWD.IN
REV.IN
VCC 1
VCC 2
MOTOR
NOISE
NOISE
DRIVE
DRIVE
IC802 MC14052BCP
16 13 10 3 6 7 8
VDD SELECT A INH 7 VEE VSS
0 1 2 3 SELECT B 0 1 2 3
12 14 15 11 9 1 5 2 4
IC1202 uPC1237HA
OVER LOAD DET
VCC ON
F/F
MUTE
OFFSET DET
LATCH/
AUTORESET
AC OFF
DET
VCC
1 2 3 4 5 6 7 8
— 70 —
SECTION 7
EXPLODED VIEWS
NOTE:
• Items marked “*” are not stocked since they are • Abbreviation
G : German model The components identified by
seldom required for routine service. Some delay
EE : East European model mark ! or dotted line with mark !
should be anticipated when ordering these items.
are critical for safety.
• The mechanical parts with no reference number in EA3 : With voltage selector Saudi Arabia model
EA4 : Without voltage selector Saudi Arabia model Replace only with part number
the exploded views are not supplied.
specified.
• Hardware (# mark) list and accessories and packing MY : Malaysia model
materials are given in the last of this parts list. SP : Singapore model
• Color Indication of Appearrance Parts HK : Hong Kong model
Example: TH : Thailand model
KNOB, BALANCE (WHITE) TW : Taiwan model
↑ IA : Indonesian model
Cabinet's Color JE : Tourist model
7-1. CASE SECTION
#1
3
2
CDM28-5BD19
#1
4
5
1
not supplied
#1
11
#1
1
6
10
7
8
9
FRONT PANEL
#2
#2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 3-363-099-01 SCREW (CASE 3 TP2) 8 1-769-940-11 WIRE (FLAT TYPE) (11 CORE) (100mm)
* 2 4-991-936-11 CASE (SILVER) 9 1-769-946-11 WIRE (FLAT TYPE) (11 CORE) (160mm)
2 4-978-748-21 CASE (BLACK) * 10 A-4303-514-A TCB BOARD (AEP,UK)
3 4-978-836-21 PANEL, LOADING (SILVER) * 10 A-4303-515-A TCB BOARD (G)
3 4-978-836-31 PANEL, LOADING (BLACK) * 10 A-4303-516-A TCB BOARD (EE)
4 4-951-620-01 SCREW (2.6X8), +BVTP * 10 A-4303-520-A TCB BOARD (JE)

* 5 4-978-853-01 CHASSIS (CDM) 10 1-233-545-11 ENCAPSULATED COMPONENT (EA4,TH)
6 1-776-166-11 WIRE (FLAT TYPE) (19 CORE) 10 1-233-546-11 ENCAPSULATED COMPONENT
7 1-773-158-11 WIRE (FLAT TYPE) (21 CORE) (240mm) (E,EA3,MY,SP,HK,TW,IA)
(EA4,TH) 11 1-751-086-11 WIRE (FLAT TYPE) (13 CORE) (EA4,TH)
7 1-773-160-11 WIRE (FLAT TYPE) (21 CORE) (260mm) 11 1-773-012-11 WIRE (FLAT TYPE) (15 CORE) (EXCEPT EA4,TH)
(EXCEPT EA4,TH)
— 71 —
7-2. BACK PANEL SECTION
CNP1601 (EXCEPT UK, E, TH, IA, JE Model)

(TH Model)
57 (HK Model)
57(EA3, MY,
CNP1601 SP,TW Model)
(UK Model)
CNP1601 57
(E, IA, JE,
Model)
CNP1601
(E, IA, JE Model)
56
51
(UK, HK Model)
54
F1603 55
#2 #2
#1
#3
#1 F1602
not supplied F1601
T1601 #1
#1
53
52
#1
The components identified by

52 mark ! or dotted line with mark !
not supplied are critical for safety.
Replace only with part number
specified.
* 51 1-659-332-11 TRANSFORMER BOARD * 56 3-703-244-11 BUSHING (2104), CORD
52 4-970-381-11 FOOT (REAR) (EA,MY,SP,HK,TW/RX50)
* 53 A-4386-430-A MAIN BOARD,COMPLETE (AEP,UK) 56 3-703-571-00 BUSHING (S) (4516), CORD (E,TH,JE)
* 53 A-4386-432-A MAIN BOARD,COMPLETE (JE) 56 4-966-266-01 BUSHING (S) (FBS002), CORD (IA)
* 53 A-4386-433-A MAIN BOARD,COMPLETE (G) ! 57 1-569-007-11 ADAPTOR, CONVERSION 2P (E,IA,JE)
! 57 1-569-008-11 ADAPTOR, CONVERSION 2P (EA3,MY,SP,TW)
* 53 A-4386-434-A MAIN BOARD,COMPLETE (E,EA3,MY,SP,HK,TW) ! 57 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
* 53 A-4386-436-A MAIN BOARD,COMPLETE (EE)
* 53 A-4386-437-A MAIN BOARD,COMPLETE (IA) ! CNP1601 1-575-651-11 CORD, POWER (AEP,G,EE,EA,MY,SP,HK,TW)
* 53 A-4386-439-A MAIN BOARD,COMPLETE (EA4,TH) ! CNP1601 1-575-653-11 CORD, POWER (E,IA,JE)
* 54 4-988-833-01 PANEL, BACK (E) ! CNP1601 1-751-326-31 CORD, POWER (TH)
! CNP1601 1-751-520-21 CORD, POWER (UK)
* 54 4-988-833-11 PANEL, BACK (EA3,TW,JE) ! F1601 1-532-504-31 FUSE,TIME-LAG (4A / 250V)
* 54 4-988-833-21 PANEL, BACK (SP,MY)
* 54 4-988-833-31 PANEL, BACK (HK) ! F1602 1-532-504-31 FUSE,TIME-LAG (4A / 250V)
* 54 4-988-833-41 PANEL, BACK (IA) ! F1603 1-532-503-31 FUSE,TIME-LAG (1.6A / 250V)
(E,EA3,MY,SP,HK,TW,IA,JE)
* 54 4-988-833-51 PANEL, BACK (EA4,TH) ! T1601 1-431-127-11 TRANSFORMER, POWER (EXCEPT AEP,UK,G,EE)
* 54 4-988-834-01 PANEL, BACK (AEP,G) ! T1601 1-431-129-11 TRANSFORMER, POWER (AEP,UK,G,EE)
* 54 4-988-834-11 PANEL, BACK (UK)
* 54 4-988-834-21 PANEL, BACK (EE)
55 4-956-370-12 BAND, PLUG FIXED (UK,HK)
— 72 —
7-3. FRONT PANEL SECTION 1
109
not supplied
110 111
Supplied with J501, J601
109
119
118
FL501
109
108 119
112 113
101
109
Supplied with S562
106 114
115
108 116
105 107
Supplied with S561 #11

104 #11 TCM-220WR2E
102 117 113
116
103
101 4-959-229-11 DETENT, CASSETTE * 111 A-4392-573-A PANEL BOARD, COMPLETE (RX50)
102 X-4948-143-1 HOLDER (B) ASSY, CASSETTE (SILVER) * 111 A-4392-581-A PANEL BOARD, COMPLETE
102 X-4948-250-1 HOLDER (B) ASSY, CASSETTE (BLACK) (E,EA3,MY,SP,HK,TW,JE)
103 4-959-232-11 SPRING (R), TORSION * 111 A-4392-589-A PANEL BOARD, COMPLETE (IA)
104 4-959-231-11 SPRING (L), TORSION * 111 A-4392-595-A PANEL BOARD, COMPLETE (EA4,TH)
* 112 1-659-333-11 JOG BOARD
105 X-4948-142-1 HOLDER (A) ASSY, CASSETTE (SILVER)
105 X-4948-249-1 HOLDER (A) ASSY, CASSETTE (BLACK) 113 3-354-957-01 JOINT (LOCK LEVER)
106 4-991-935-01 KNOB, JOG (BLACK) * 114 3-354-953-01 LEVER (LOCK LEVER L)
106 4-991-935-11 KNOB, JOG (SILVER) * 115 3-354-954-01 LEVER (LOCK LEVER R)
107 4-991-934-01 KNOB (VOL) (BLACK) * 116 3-354-963-01 DAMPER
* 117 4-980-439-01 FULCRUM, HOLDER
107 4-991-934-11 KNOB (VOL) (SILVER)
108 4-980-219-01 BUTTON (EJECT) (BLACK) 118 4-978-168-31 HOLDER, (FL TUBE)
108 4-980-219-21 BUTTON (EJECT) (SILVER) * 119 4-932-810-11 CUSHION (FL)
109 4-951-620-01 SCREW (2.6X8), +BVTP FL501 1-517-489-11 INDICATOR TUBE, FLUORESCENT (EA4,TH,IA)
* 110 1-659-331-11 HP BOARD FL501 1-517-660-11 INDICATOR TUBE, FLUORESCENT
(EXCEPT EA4,TH,IA)
— 73 —
7-4. FRONT PANEL SECTION 2
151
158
157
156 159
164
163
160
154
161
152
not supplied 162
153
155
151 X-4948-144-1 PANEL ASSY, FRONT (BLACK) 159 X-4948-139-1 BUTTON (T/B) ASSY (BLACK)
151 X-4948-145-1 PANEL ASSY, FRONT (SILVER) 159 X-4948-246-1 BUTTON (T/B) ASSY (SILVER)
152 4-978-716-01 WINDOW (FL) 160 X-4946-801-1 BUTTON (ENTER/NEXT) ASSY (BLACK)
153 4-978-745-21 PLATE, ORNAMENTAL, JOG 160 X-4948-245-1 BUTTON (ENTER/NEXT) ASSY (SILVER)
154 4-962-708-11 EMBLEM (4-A), SONY 161 X-4946-707-1 BUTTON (TC-PLAY) ASSY (BLACK)
155 4-930-336-61 FOOT (FELT) 161 X-4948-243-1 BUTTON (TC-PLAY) ASSY (SILVER)
156 4-978-744-31 PLATE (MULTI), ORNAMENTAL 162 4-978-851-01 INDICATOR (REC)
157 4-978-742-01 HOLDER (MULTI), LED 163 X-4946-713-1 BUTTON (CD-PLAY) ASSY (BLACK)
158 4-978-839-01 BUTTON (MULTI) (BLACK) 163 X-4948-244-1 BUTTON (CD-PLAY) ASSY (SILVER)
158 4-978-839-11 BUTTON (MULTI) (SILVER) 164 4-978-837-11 BUTTON (POWER) (SILVER)
164 4-978-837-01 BUTTON (POWER) (BLACK)
— 74 —
7-5. CD MECHANISM SECTION
(CDM28-5BD19)
205
#1
203 204
206
(including rB)
207
#1
202
208 209
210
M903
rB
BU-5BD19
213
211
#1
201
212
201 4-960-836-01 TABLE, DISC 208 4-960-838-03 BASE (MD)
202 4-960-835-01 HOLDER (M) 209 4-917-583-21 BRACKET, YOKE
203 1-452-719-11 MAGNET ASSY 210 4-933-134-01 SCREW(+PTPWH M2.6X6)
204 4-960-842-01 GEAR (P) 211 4-959-996-01 SPRING (932), COMPRESSION
205 4-960-841-01 PULLEY (S) 212 4-960-834-01 HOLDER (BU)
206 4-927-649-01 BELT * 213 1-650-836-11 LOADING BOARD

* 207 4-960-839-01 CAM M903 A-4604-363-A MOTOR (L)ASSY (LOADING)
— 75 —
7-6. BASE UNIT SECTION
(BU-5BD19)
251
252
253
#5
255
M101 254
M102
254
S101
256
257
mark ! or dotted line with mark !
258 Replace only with part number
specified.
! 251 8-848-387-01 OPTICAL PICK-UP KSS-213BA/S-N 256 4-917-564-01 GEAR (P), FLATNESS
252 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) * 257 A-4673-402-A BD BOARD, COMPLETE
253 4-917-567-01 GEAR (M) 258 4-951-620-01 SCREW (2.6X8), +BVTP
254 4-951-940-01 INSULATOR (BU) M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
255 4-917-565-01 SHAFT,SLED M102 X-4917-504-1 MOTOR ASSY (SLED)
S101 1-572-085-11 SWITCH, LEAF (LIMIT)
— 76 —
7-7. TC MECHANISM SECTION 1
(TCM-220WR2E)
320 #6
(Including p A)
319
324 •A
#6
321
315
314
HP101 322
(including •B
• A) not supplied 316
312 323
307 •A
313 319
303 315
306 308 311 323
314
312
305 316
309 322
317
323 •B
310 not supplied
323
319
not supplied
304 HRPE101 318 307
(including
not supplied • B) 313
306
305 309 311
not supplied
302 301
#10
310 308
not supplied
304 303
301
302 #10 not supplied
301 3-908-560-01 SPRING,AZIMUTH ADJUSTMENT 314 3-908-613-01 GEAR (S), REEL
302 3-919-684-01 SCREW, AZIMUTH ADJUSTMENT 315 3-917-141-01 SPRING, COMPRESSION
303 X-3373-113-1 SLIDER (HEAD) ASSY 316 X-3371-305-1 REEL (T) ASSY
304 3-908-556-01 SPRING, HEAD TOGGLE 317 3-669-465-01 WASHER (1.5), STOPPER
305 3-908-558-02 FITTING BLOCK,HEAD 318 X-3370-173-1 TU ASSY
306 3-908-557-02 ROTARY BLOCK,HEAD 319 3-939-862-01 CLIP

* 307 3-908-559-01 STOPPER, AZIMUTH * 320 A-2007-435-A AUDIO BOARD, COMPLETE
308 3-908-555-01 SLIDER (REV SLIDER) 321 3-930-972-01 DETENT,HALF
309 3-917-143-11 SPRING, TENSION 322 3-917-142-01 SPRING, COMPRESSION
310 3-388-848-01 SCREW (P2X6) (B TIGHT) 323 3-355-808-02 PINCH ROLLER
324 3-938-863-01 STOPPER
311 3-939-371-01 SPRING (1), TENSION
312 X-3369-909-1 PINCH LEVER (REV) ASSY HP101 1-500-093-11 HEAD,MAGNETIC (PLAYBACK) (DECK A)
313 X-3369-908-1 PINCH LEVER (FWD) ASSY HRPE101 1-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE) (DECK B)
— 77 —
7-8. TC MECHANISM SECTION 2
(TCM-220WR2E)
pA: MOTOR board (Supplied with AUDIO board)
375 M2
pA
368 369
#9
#4
367 370 360

371
352 #9
361
371
359 366 360 374
363 #10
365
358 357
356
373
355
357 362 369

354
372 364
363
#8
353
#7 351
#7 352
M1 not supplied
351 3-908-597-01 CAM (A) 364 X-3370-171-1 FLYWHEEL (BR) ASSY
352 3-908-608-11 SCREW, STEP 365 3-908-600-01 LEVER (REV-B)
353 X-3372-930-1 ARM (A) ASSY, FR * 366 1-650-669-11 LEAF SWITH BOARD
354 X-3370-882-1 FLYWHEEL (AR) ASSY 367 3-908-598-01 CAM (B)
368 X-3372-931-1 ARM (B) ASSY,FR
355 3-928-047-01 PULLEY, TENSION
356 3-908-601-01 SPRING (REV LEVER),TORSION 369 3-914-111-01 SPRING (FR), TORSION
357 3-908-599-01 LEVER (REV-A) 370 3-908-604-01 LEVER (TRIGGER B)
358 3-908-603-01 LEVER (TRIGGER A) 371 3-911-115-01 WASHER, STOPPER
359 X-3370-108-1 FLYWHEEL (BF) ASSY 372 3-917-176-11 BELT (B)
373 X-3370-172-1 FLYWHEEL (AF) ASSY
360 3-908-605-01 SPRING (TRIGGER), TORSION
361 3-908-609-01 GEAR, TRIGGER 374 X-3371-441-1 CHASSIS ASSY, MECHANICAL
362 3-913-845-11 BELT (A) * 375 A-2007-435-A AUDIO BOARD, COMPLETE
363 3-913-846-11 BELT (FR) M1 X-3371-223-1 MOTOR ASSY (CAPSTAN)
M2 A-2004-410-A MOTOR ASSY, DC (TRIGGER)
— 78 —
SECTION 8
ELECTRICAL PARTS LIST AUDIO
Note:
The components identified by • Due to standardization, replacements in the parts • COILS
mark ! or dotted line with mark ! list may be different from the parts specified in the uH : µ H
are critical for safety. diagrams or the components used on the set. • Abbreviation
Replace only with part number • Items marked “*” are not stocked since they are G : German model
specified. seldom required for routine service. Some delay EE : East European model
should be anticipated when ordering these items. EA3 : With voltage selector Saudi Arabia model
• RESISTORS EA4 : Without voltage selector Saudi Arabia model
When indicating parts by reference
All resistors are in ohms MY : Malaysia model
number, please include the board
METAL: Metal-film resistor SP : Singapore model
name.
METAL OXIDE: Metal Oxide-film resistor HK : Hong Kong model
F : nonflammable TH : Thailand model
• SEMICONDUCTORS TW : Taiwan model
In each case, u: µ , for example: IA : Indonesian model
uA...: µ A..., uPA...: µ PA..., uPB...: µ PB..., JE : Tourist model
uPC...: µ PC..., uPD...: µ PD...
• CAPACITORS
uF : µ F
* A-2007-435-A AUDIO BOARD, COMPLETE < CONNECTOR >
*********************
(including MOTOR BOARD) CN601 1-695-382-31 PIN, CONNECTOR (PC BOARD) 21P
CN602 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P
< CPACITOR > * CN651 1-564-521-11 PLUG, CONNECTOR 6P
C301 1-162-289-31 CERAMIC 390PF 10% 50V < IC >

C302 1-126-968-11 ELECT 100uF 20% 6.3V
C303 1-162-282-31 CERAMIC 100PF 10% 50V IC601 8-759-111-44 IC uPC4570C-1
C304 1-130-483-00 MYLAR 0.01uF 5% 50V IC602 8-759-143-54 IC uPC1330HA
C305 1-107-715-11 ELECT 22uF 20% 16V IC611 8-759-111-44 IC uPC4570C-1
C311 1-162-289-31 CERAMIC 390PF 10% 50V < COIL >

C313 1-162-282-31 CERAMIC 100PF 10% 50V
C314 1-130-487-00 MYLAR 0.022uF 5% 50V L331 1-410-780-11 INDUCTOR 27mH
C315 1-126-233-11 ELECT 22uF 20% 25V L431 1-410-780-11 INDUCTOR 27mH
C331 1-137-427-11 FILM 120PF 5% 50V
< TRANSISTOR >
C332 1-162-288-31 CERAMIC 330PF 10% 50V
C333 1-162-209-31 CERAMIC 27PF 5% 50V Q621 8-729-142-46 TRANSISTOR 2SC2001-LK
C401 1-162-289-31 CERAMIC 390PF 10% 50V Q622 8-729-142-46 TRANSISTOR 2SC2001-LK
C402 1-126-968-11 ELECT 100uF 20% 6.3V Q623 8-729-030-18 TRANSISTOR 2SD2525
C403 1-162-282-31 CERAMIC 100PF 10% 50V Q651 8-729-900-65 TRANSISTOR DTA144ES
C404 1-130-483-00 MYLAR 0.01uF 5% 50V < RESISTOR >

C405 1-107-715-11 ELECT 22uF 20% 16V
C411 1-162-289-31 CERAMIC 390PF 10% 50V R301 1-247-881-00 CARBON 120K 5% 1/4W
C413 1-162-282-31 CERAMIC 100PF 10% 50V R302 1-249-409-11 CARBON 220 5% 1/4W
C414 1-130-487-00 MYLAR 0.022uF 5% 50V R303 1-249-433-11 CARBON 22K 5% 1/4W
R304 1-247-889-00 CARBON 270K 5% 1/4W
C415 1-126-233-11 ELECT 22uF 20% 25V R305 1-247-858-11 CARBON 13K 5% 1/4W
C431 1-137-427-11 FILM 120PF 5% 50V
C432 1-162-288-31 CERAMIC 330PF 10% 50V R311 1-247-881-00 CARBON 120K 5% 1/4W
C433 1-162-209-31 CERAMIC 27PF 5% 50V R312 1-247-807-31 CARBON 100 5% 1/4W
R315 1-247-850-11 CARBON 6.2K 5% 1/4W
C611 1-124-907-11 ELECT 10uF 20% 50V
C621 1-137-150-11 FILM 0.01uF 5% 100V R402 1-249-409-11 CARBON 220 5% 1/4W
C622 1-126-961-11 ELECT 2.2uF 20% 50V R403 1-249-433-11 CARBON 22K 5% 1/4W
R404 1-247-889-00 CARBON 270K 5% 1/4W
C623 1-136-155-00 FILM 0.015uF 5% 50V R405 1-247-858-11 CARBON 13K 5% 1/4W
C624 1-130-481-00 MYLAR 0.0068uF 5% 50V
C625 1-130-481-00 MYLAR 0.0068uF 5% 50V R411 1-247-881-00 CARBON 120K 5% 1/4W
C627 1-124-903-11 ELECT 1uF 20% 50V R412 1-247-807-31 CARBON 100 5% 1/4W
C628 1-136-153-00 FILM 0.01uF 5% 50V R414 1-247-882-11 CARBON 130K 5% 1/4W
R415 1-247-850-11 CARBON 6.2K 5% 1/4W
C651 1-161-494-00 CERAMIC 0.022uF 25V
R601 1-249-409-11 CARBON 220 5% 1/4W
R602 1-249-409-11 CARBON 220 5% 1/4W
R608 1-249-409-11 CARBON 220 5% 1/4W
— 79 —
AUDIO BD
R609 1-249-433-11 CARBON 22K 5% 1/4W C132 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
R611 1-249-409-11 CARBON 220 5% 1/4W C133 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
C134 1-164-346-11 CERAMIC CHIP 1uF 16V
R612 1-249-409-11 CARBON 220 5% 1/4W C135 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
! R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F C136 1-164-005-11 CERAMIC CHIP 0.47uF 25V
! R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
R623 1-249-432-11 CARBON 18K 5% 1/4W C137 1-164-232-11 CERAMIC CHIP 0.01uF 50V
R624 1-249-432-11 CARBON 18K 5% 1/4W C139 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C140 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R652 1-247-856-00 CARBON 11K 5% 1/4W
R653 1-249-441-11 CARBON 100K 5% 1/4W C145 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
C146 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
< VARIABLE RESISTOR > C147 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C148 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
RV301 1-238-598-11 RES, ADJ, CARBON 2.2K C149 1-164-346-11 CERAMIC CHIP 1uF 16V
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K
RV341 1-238-551-11 RES, ADJ, CARBON 220K C153 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
RV401 1-238-598-11 RES, ADJ, CARBON 2.2K C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
RV411 1-238-598-11 RES, ADJ, CARBON 2.2K
< CONNECTOR >
RV441 1-238-551-11 RES, ADJ, CARBON 220K
RV651 1-238-599-11 RES, ADJ, CARBON 4.7K CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P
RV652 1-238-599-11 RES, ADJ, CARBON 4.7K CNU102 1-770-013-11 CONNECTOR, FFC/FPC 19P
< TRANSFORMER > < IC >
T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION IC101 8-752-069-56 IC CXA1782BQ

************************************************************ IC102 8-759-291-06 IC BA6397FP
IC103 8-752-372-94 IC CXD2507AQ
* A-4673-402-A BD BOARD, COMPLETE IC104 8-759-185-29 IC PCM1710U-B
******************
< TRANSISTOR >
< CAPACITOR >
Q101 8-729-010-08 TRANSISTOR MSB710-R
C101 1-126-607-11 ELECT CHIP 47uF 20% 4V Q102 8-729-424-08 TRANSISTOR UN2111
C102 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V Q103 8-729-421-22 TRANSISTOR UN2211
C103 1-164-346-11 CERAMIC CHIP 1uF 16V
C105 1-163-038-91 CERAMIC CHIP 0.1uF 25V < RESISTOR >
R102 1-216-001-00 METAL CHIP 10 5% 1/10W
C107 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V R103 1-216-049-91 METAL GLAZE 1K 5% 1/10W
C108 1-164-232-11 CERAMIC CHIP 0.01uF 50V R104 1-216-097-91 METAL GLAZE 100K 5% 1/10W
C109 1-164-232-11 CERAMIC CHIP 0.01uF 50V R105 1-216-093-00 METAL CHIP 68K 5% 1/10W
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V R106 1-216-093-00 METAL CHIP 68K 5% 1/10W
C111 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R107 1-216-093-00 METAL CHIP 68K 5% 1/10W
C113 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V R109 1-216-097-91 METAL GLAZE 100K 5% 1/10W
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V R113 1-216-083-00 METAL CHIP 27K 5% 1/10W
R114 1-216-101-00 METAL CHIP 150K 5% 1/10W
C118 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
C119 1-163-038-91 CERAMIC CHIP 0.1uF 25V R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
C120 1-135-201-11 TANTALUM CHIP 10uF 20% 4V R118 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R119 1-216-089-91 METAL GLAZE 47K 5% 1/10W
C124 1-126-607-11 ELECT CHIP 47uF 20% 4V R122 1-216-097-91 METAL GLAZE 100K 5% 1/10W
R124 1-216-091-00 METAL CHIP 56K 5% 1/10W
C127 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V R125 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V R126 1-216-063-91 METAL GLAZE 3.9K 5% 1/10W
C131 1-163-038-91 CERAMIC CHIP 0.1uF 25V mark ! or dotted line with mark !
specified.
— 80 —
BD HP JOG
R128 1-216-105-91 METAL GLAZE 220K 5% 1/10W C647 1-162-282-31 CERAMIC 100PF 10% 50V
R129 1-216-049-91 METAL GLAZE 1K 5% 1/10W C648 1-124-257-00 ELECT 2.2uF 20% 50V
R130 1-216-079-00 METAL CHIP 18K 5% 1/10W C649 1-124-589-11 ELECT 47uF 20% 16V
R131 1-216-079-00 METAL CHIP 18K 5% 1/10W C650 1-124-589-11 ELECT 47uF 20% 16V
R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C651 1-162-306-11 CERAMIC 0.01uF 20% 16V
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C9998 1-161-494-00 CERAMIC 0.022uF 25V
R134 1-216-065-00 METAL CHIP 4.7K 5% 1/10W < CONNECTOR >

R135 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R136 1-216-073-00 METAL CHIP 10K 5% 1/10W * CN513 1-568-935-11 PIN, CONNECTOR 8P
R137 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R138 1-216-049-91 METAL GLAZE 1K 5% 1/10W < IC >
R139 1-216-033-00 METAL CHIP 220 5% 1/10W IC601 8-759-634-51 IC M5218AP

R140 1-216-081-00 METAL CHIP 22K 5% 1/10W
R141 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < JACK >
R142 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R143 1-216-121-91 METAL GLAZE 1M 5% 1/10W J501 1-778-605-11 JACK (LARGE TYPE)(PHONES)
(EXCEPT AEP,UK,G,EE,IA)
R144 1-216-073-00 METAL CHIP 10K 5% 1/10W J501 1-774-728-11 JACK (PHONES) (IA)
R145 1-216-097-91 METAL GLAZE 100K 5% 1/10W J501 1-770-226-11 JACK (LARGE TYPE)(PHONES)(AEP,UK,G,EE)
R146 1-216-097-91 METAL GLAZE 100K 5% 1/10W J601 1-778-605-11 JACK (LARGE TYPE)(MIX MIC)
R147 1-216-049-91 METAL GLAZE 1K 5% 1/10W (EXCEPT AEP,UK,G,EE,IA)
R148 1-216-049-91 METAL GLAZE 1K 5% 1/10W
J601 1-774-728-11 JACK (MIX MIC) (IA)
R149 1-216-049-91 METAL GLAZE 1K 5% 1/10W J601 1-770-226-11 JACK (LARGE TYPE)(MIX MIC)(AEP,UK,G,EE)
R150 1-216-037-00 METAL CHIP 330 5% 1/10W
R151 1-216-037-00 METAL CHIP 330 5% 1/10W < RESISTOR >
R152 1-216-037-00 METAL CHIP 330 5% 1/10W
R153 1-216-082-00 METAL GLAZE 24K 5% 1/10W R640 1-249-429-11 CARBON 10K 5% 1/4W
R641 1-249-441-11 CARBON 100K 5% 1/4W
R154 1-216-065-00 METAL CHIP 4.7K 5% 1/10W R642 1-249-417-11 CARBON 1K 5% 1/4W
R156 1-216-085-00 METAL CHIP 33K 5% 1/10W R643 1-249-417-11 CARBON 1K 5% 1/4W
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R644 1-249-435-11 CARBON 33K 5% 1/4W
R158 1-216-001-00 METAL CHIP 10 5% 1/10W
R645 1-249-429-11 CARBON 10K 5% 1/4W
< VARIABLE RESISTOR > R646 1-247-881-00 CARBON 120K 5% 1/4W
R647 1-247-807-31 CARBON 100 5% 1/4W
RV101 1-223-587-11 RES, ADJ, CARBON 22K ************************************************************
RV101 1-241-396-11 RES, ADJ, METAL GLAZE 22K
RV102 1-223-587-11 RES, ADJ, CARBON 22K * 1-659-333-11 JOG BOARD
RV102 1-241-396-11 RES, ADJ, METAL GLAZE 22K *********
< CAPACITOR >
RV103 1-241-396-11 RES, ADJ, METAL GLAZE 22K
C524 1-162-306-11 CERAMIC 0.01uF 20% 16V
< SWITCH > C525 1-162-306-11 CERAMIC 0.01uF 20% 16V
C526 1-162-306-11 CERAMIC 0.01uF 20% 16V
S101 1-572-085-11 SWITCH, LEAF (LIMIT) C527 1-162-306-11 CERAMIC 0.01uF 20% 16V
< VIBRATOR > < DIODE >
X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) D582 8-719-812-44 DIODE TLO124 (ENTER/NEXT)
************************************************************
< RESISTOR >
* 1-659-331-11 HP BOARD
******** R511 1-249-409-11 CARBON 220 5% 1/4W
R512 1-249-411-11 CARBON 330 5% 1/4W
< CAPACITOR > R513 1-249-413-11 CARBON 470 5% 1/4W
R514 1-249-415-11 CARBON 680 5% 1/4W
C520 1-162-306-11 CERAMIC 0.01uF 20% 16V R560 1-249-417-11 CARBON 1K 5% 1/4W
C521 1-162-306-11 CERAMIC 0.01uF 20% 16V
C640 1-162-306-11 CERAMIC 0.01uF 20% 16V R582 1-249-407-11 CARBON 150 5% 1/4W
C641 1-124-257-00 ELECT 2.2uF 20% 50V
C642 1-162-294-31 CERAMIC 0.001uF 10% 50V < SWITCH >
C643 1-162-282-31 CERAMIC 100PF 10% 50V S511 1-554-303-21 SWITCH, TACTILE (FREQUENCY -)
C644 1-162-290-31 CERAMIC 470PF 10% 50V S512 1-554-303-21 SWITCH, TACTILE (FREQUENCY +)
C645 1-124-465-00 ELECT 0.47uF 20% 50V S513 1-554-303-21 SWITCH, TACTILE (ENTER/NEXT)
C646 1-162-282-31 CERAMIC 100PF 10% 50V S514 1-554-303-21 SWITCH, TACTILE (DBFB)
— 81 —
JOG LEAF SWITCH LOADING MAIN
S560 1-554-303-21 SWITCH, TACTILE (KARAOKE PON/MPX) < CAPACITOR >
S561 1-467-869-11 ENCODER, ROTARY (VOLUME) C201 1-126-961-11 ELECT 2.2uF 20% 50V
S562 1-467-968-11 ENCODER, ROTARY (MULTI JOG STATION) C202 1-162-600-11 CERAMIC 0.0047uF 30% 16V
************************************************************ C203 1-124-472-11 ELECT 470uF 20% 10V
C204 1-162-282-31 CERAMIC 100PF 10% 50V
* 1-650-669-11 LEAF SWITCH BOARD C205 1-162-282-31 CERAMIC 100PF 10% 50V
*****************
C206 1-162-306-11 CERAMIC 0.01uF 20% 16V
< CONNECTOR > C207 1-162-306-11 CERAMIC 0.01uF 20% 16V
C208 1-162-306-11 CERAMIC 0.01uF 20% 16V
* CN1001 1-568-854-11 SOCKET, CONNECTOR 11P C209 1-126-952-11 ELECT 1000uF 20% 16V
(EXCEPT EA4,TH)
< TRANSISTOR > C209 1-126-797-11 ELECT 1000uF 20% 10V
(EA4,TH)
Q1001 8-749-010-90 TRANSISTOR
PHOTO REFLECTOR NJL5165KA-H C210 1-162-306-11 CERAMIC 0.01uF 20% 16V
Q1002 8-749-010-90 TRANSISTOR C211 1-126-933-11 ELECT 100uF 20% 10V
PHOTO REFLECTOR NJL5165KA-H C251 1-126-961-11 ELECT 2.2uF 20% 50V
C252 1-162-600-11 CERAMIC 0.0047uF 30% 16V
< RESISTOR > C301 1-130-479-00 MYLAR 0.0047uF 5% 50V
R1001 1-247-818-11 CARBON 300 5% 1/4W C302 1-162-290-31 CERAMIC 470PF 10% 50V
R1002 1-247-820-11 CARBON 360 5% 1/4W C303 1-136-165-00 FILM 0.1uF 5% 50V
R1003 1-249-414-11 CARBON 560 5% 1/4W C305 1-126-960-11 ELECT 1uF 20% 50V
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W C307 1-126-964-11 ELECT 10uF 20% 50V
R1005 1-247-818-11 CARBON 300 5% 1/4W C308 1-126-964-11 ELECT 10uF 20% 50V
< SWITCH > C309 1-126-960-11 ELECT 1uF 20% 50V

C310 1-126-933-11 ELECT 100uF 20% 10V
S1001 1-692-832-11 SWITCH, PUSH (1 KEY)(A PLAY) C351 1-130-479-00 MYLAR 0.0047uF 5% 50V
S1002 1-692-832-11 SWITCH, PUSH (1 KEY)(B PLAY) C352 1-162-290-31 CERAMIC 470PF 10% 50V
S1003 1-572-248-11 SWITCH, LEAF (A HALF) C353 1-136-165-00 FILM 0.1uF 5% 50V
S1004 1-571-281-21 SWITCH, LEAF (A CrO2)
S1005 1-571-281-21 SWITCH, LEAF (REC A) C355 1-126-960-11 ELECT 1uF 20% 50V
C357 1-126-964-11 ELECT 10uF 20% 50V
S1006 1-572-248-11 SWITCH, LEAF (B HALF) C358 1-126-964-11 ELECT 10uF 20% 50V
S1008 1-571-281-21 SWITCH, LEAF (B CrO2) C359 1-126-960-11 ELECT 1uF 20% 50V
S1009 1-571-281-21 SWITCH, LEAF (REC B) C360 1-126-933-11 ELECT 100uF 20% 10V
************************************************************
C401 1-164-159-11 CERAMIC 0.1uF 50V
* 1-650-836-11 LOADING BOARD C402 1-164-159-11 CERAMIC 0.1uF 50V
************* C403 1-164-159-11 CERAMIC 0.1uF 50V
C404 1-126-933-11 ELECT 100uF 20% 16V
< CONNECTOR > C405 1-126-935-11 ELECT 470uF 20% 16V
* CN291 1-568-943-11 PIN, CONNECTOR 5P C701 1-162-306-11 CERAMIC 0.01uF 20% 16V
C702 1-126-926-11 ELECT 1000uF 20% 10V
< SWITCH > C703 1-126-964-11 ELECT 10uF 20% 50V
C704 1-136-165-00 MYLAR 0.1uF 10% 50V
S291 1-572-086-11 SWITCH, LEAF (LOAD OUT) C705 1-136-165-00 FILM 0.1uF 5% 50V
S292 1-572-086-11 SWITCH, LEAF (LOAD IN)
************************************************************ C706 1-126-965-11 ELECT 22uF 20% 50V
C707 1-162-205-31 CERAMIC 18PF 5% 50V
* A-4386-430-A MAIN
BOARD, COMPLETE (AEP,UK) C708 1-162-205-31 CERAMIC 18PF 5% 50V
* A-4386-432-A MAIN
BOARD, COMPLETE (JE) C710 1-162-306-11 CERAMIC 0.01uF 20% 16V
* A-4386-433-A MAIN
BOARD, COMPLETE (G) C713 1-162-306-11 CERAMIC 0.01uF 20% 16V
* A-4386-434-A MAIN
BOARD, COMPLETE
(E,EA3,MY,SP,HK,TW) C720 1-164-159-11 CERAMIC 0.1uF 50V
* A-4386-436-A MAIN BOARD, COMPLETE (EE) C789 1-126-923-11 ELECT 220uF 20% 10V
* A-4386-437-A MAIN BOARD, COMPLETE (IA) C810 1-162-306-11 CERAMIC 0.01uF 20% 16V
* A-4386-439-A MAIN BOARD, COMPLETE (EA4,TH) C811 1-162-306-11 CERAMIC 0.01uF 20% 16V
******************************* C821 1-162-286-31 CERAMIC 220PF 10% 50V
* 1-537-738-21 TERMINAL, EARTH (EA4,TH) C825 1-109-889-11 ELECT 1uF 20% 50V
1-537-770-21 TERMINAL BOARD, GROUND (AEP,UK,G,EE) C831 1-162-286-31 CERAMIC 220PF 10% 50V
1-533-217-31 HOLDER, FUSE C871 1-162-286-31 CERAMIC 220PF 10% 50V
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S C881 1-162-286-31 CERAMIC 220PF 10% 50V
C901 1-136-169-00 FILM 0.22uF 5% 50V
C902 1-136-169-00 FILM 0.22uF 5% 50V
— 82 —
MAIN
C903 1-136-495-11 FILM 0.068uF 5% 50V C1022 1-126-968-11 ELECT 100uF 20% 50V
C905 1-136-156-00 FILM 0.018uF 5% 50V
C1026 1-126-925-11 ELECT 470uF 20% 10V
C907 1-130-480-00 MYLAR 0.0056uF 5% 50V C1201 1-126-963-11 ELECT 4.7uF 20% 50V
C908 1-162-600-11 CERAMIC 0.0047uF 30% 16V C1202 1-162-288-31 CERAMIC 330PF 10% 50V
C909 1-130-474-00 MYLAR 0.0018uF 5% 50V C1203 1-162-286-31 CERAMIC 220PF 10% 50V
C910 1-126-964-11 ELECT 10uF 20% 50V (EXCEPT IA)
C911 1-126-964-11 ELECT 10uF 20% 50V
C1204 1-126-967-11 ELECT 47uF 20% 10V
C914 1-126-964-11 ELECT 10uF 20% 50V C1208 1-126-965-11 ELECT 22uF 20% 50V
C915 1-162-600-11 CERAMIC 0.0047uF 30% 16V C1210 1-136-495-11 FILM 0.068uF 5% 50V
C930 1-164-159-11 CERAMIC 0.1uF 50V
C1211 1-136-495-11 FILM 0.068uF 5% 50V
C931 1-162-306-11 CERAMIC 0.01uF 20% 16V (EA4,TH,IA)
C933 1-126-959-11 ELECT 0.47uF 20% 50V C1220 1-126-925-11 ELECT 470uF 20% 10V
C935 1-164-159-11 CERAMIC 0.1uF 50V C1221 1-126-933-11 ELECT 100uF 20% 10V
(EXCEPT IA) C1222 1-126-923-11 ELECT 220uF 20% 10V
C938 1-162-290-31 CERAMIC 470PF 10% 50V
C1224 1-126-961-11 ELECT 2.2uF 20% 50V
C939 1-126-967-11 ELECT 47uF 20% 10V C1225 1-162-284-31 CERAMIC 150PF 10% 50V
C940 1-126-967-11 ELECT 47uF 20% 10V C1227 1-164-159-11 CERAMIC 0.1uF 50V
C951 1-136-169-00 FILM 0.22uF 5% 50V (EXCEPT AEP,UK,EA4,TH,IA)
C954 1-136-495-11 FILM 0.068uF 5% 50V C1246 1-164-159-11 CERAMIC 0.1uF 50V
C955 1-136-156-00 FILM 0.018uF 5% 50V (AEP,UK)
C956 1-136-156-00 FILM 0.018uF 5% 50V C1248 1-136-495-11 FILM 0.068uF 5% 50V
C957 1-130-480-00 MYLAR 0.0056uF 5% 50V (AEP,UK,G,EE)
C958 1-162-600-11 CERAMIC 0.0047uF 30% 16V C1249 1-136-495-11 FILM 0.068uF 5% 50V
(AEP,UK,G,EE)
C959 1-130-474-00 MYLAR 0.0018uF 5% 50V C1250 1-162-306-11 CERAMIC 0.01uF 20% 16V
C960 1-126-964-11 ELECT 10uF 20% 50V (AEP,UK,G,EE)
C961 1-126-964-11 ELECT 10uF 20% 50V C1251 1-126-963-11 ELECT 4.7uF 20% 50V
C962 1-136-165-00 FILM 0.1uF 5% 50V
C963 1-136-165-00 FILM 0.1uF 5% 50V C1252 1-162-288-31 CERAMIC 330PF 10% 50V
C1253 1-162-286-31 CERAMIC 220PF 10% 50V
C964 1-126-964-11 ELECT 10uF 20% 50V (EXCEPT IA)
C965 1-162-600-11 CERAMIC 0.0047uF 30% 16V C1254 1-126-967-11 ELECT 47uF 20% 10V
C1003 1-126-964-11 ELECT 10uF 20% 50V
C1260 1-136-495-11 FILM 0.068uF 5% 50V
C1005 1-126-964-11 ELECT 10uF 20% 50V C1261 1-136-495-11 FILM 0.068uF 5% 50V
C1006 1-126-933-11 ELECT 100uF 20% 10V (EA4,TH,IA)
C1009 1-162-306-11 CERAMIC 0.01uF 20% 16V C1272 1-164-159-11 CERAMIC 0.1uF 50V
(AEP,UK,G,EE)
C1010 1-136-165-00 FILM 0.1uF 5% 50V
C1011 1-136-165-00 FILM 0.1uF 5% 50V C1296 1-164-159-11 CERAMIC 0.1uF 50V
C1012 1-126-964-11 ELECT 10uF 20% 50V (AEP,UK)
C1013 1-126-916-11 ELECT 1000uF 20% 6.3V C1298 1-136-495-11 FILM 0.068uF 5% 50V
C1299 1-136-495-11 FILM 0.068uF 5% 50V
C1016 1-126-952-11 ELECT 1000uF 20% 16V C1300 1-162-306-11 CERAMIC 0.01uF 20% 16V
(EXCEPT EA4,TH) (AEP,UK,G,EE)
C1016 1-126-797-11 ELECT 1000uF 20% 10V
(EA4,TH) < CONNECTOR >
C1017 1-126-925-11 ELECT 470uF 20% 10V
C1018 1-126-942-61 ELECT 1000uF 20% 25V CN201 1-770-067-11 CONNECTOR, FFC/FPC 19P
CN401 1-568-838-11 SOCKET, CONNECTOR 21P
C1019 1-126-934-11 ELECT 220uF 20% 16V * CN402 1-568-830-11 SOCKET, CONNECTOR 11P
C1020 1-126-947-11 ELECT 47uF 20% 35V * CN403 1-568-449-11 HOUSING, CONNECTOR(PC BOARD)3P
C1021 1-126-964-11 ELECT 10uF 20% 50V * CN404 1-568-449-11 HOUSING, CONNECTOR(PC BOARD)3P
— 83 —
MAIN
* CN702 1-568-830-11 SOCKET, CONNECTOR 11P IC401 8-759-289-38 IC HA12195NT
* CN703 1-568-834-11 SOCKET, CONNECTOR 15P (EXCEPT EA4,TH) IC402 8-759-822-09 IC LB1641
* CN703 1-568-832-11 SOCKET, CONNECTOR 13P (EA4,TH) IC701 8-759-451-82 IC TMP87CS64YF-6521
< DIODE > IC702 8-759-165-80 IC PST600C-T

IC802 8-759-000-48 IC MC14052BCP
D201 8-719-987-63 DIODE 1N4148M IC901 8-759-331-39 IC M62427FP
D202 8-719-987-63 DIODE 1N4148M IC1001 8-759-231-53 IC TA7805S
D205 8-719-010-33 DIODE UZ-4.7BSB IC1002 8-759-604-86 IC M5F7807L
D401 8-719-933-54 DIODE HZS9A2L
D701 8-719-987-63 DIODE 1N4148M IC1003 8-759-604-86 IC M5F7807L
IC1004 8-759-604-90 IC M5F7907L
D702 8-719-987-63 DIODE 1N4148M IC1201 8-749-920-09 IC STK-4152MK2K
D703 8-719-987-63 DIODE 1N4148M IC1202 8-759-111-68 IC uPC1237HA
D704 8-719-987-63 DIODE 1N4148M
D705 8-719-987-63 DIODE 1N4148M < JACK >
D706 8-719-024-99 DIODE 11ES2-NTA2B
J801 1-695-188-31 JACK, PIN 4P (MD AUDIO IN,OUT)
D707 8-719-987-63 DIODE 1N4148M J1201 1-774-785-11 JACK, PIN 1P (SUPER WOOFER)
D708 8-719-987-63 DIODE 1N4148M (EXCEPT AEP,UK,G,EE)
D1001 8-719-024-99 DIODE 11ES2-NTA2B
D1003 8-719-024-99 DIODE 11ES2-NTA2B < COIL >
D1004 8-719-024-99 DIODE 11ES2-NTA2B
L1201 1-420-872-00 COIL, AIR-CORE (AEP,UK,G,EE)
D1005 8-719-024-99 DIODE 11ES2-NTA2B L1251 1-420-872-00 COIL, AIR-CORE (AEP,UK,G,EE)
D1006 8-719-024-99 DIODE 11ES2-NTA2B
D1007 8-719-987-63 DIODE 1N4148M < TRANSISTOR >
D1008 8-719-001-42 DIODE UZL-11M1
D1009 8-719-987-63 DIODE 1N4148M Q301 8-729-119-78 TRANSISTOR 2SC403SP-51
Q351 8-729-119-78 TRANSISTOR 2SC403SP-51
D1011 8-719-011-54 DIOD UZ-4.3BS-TA Q402 8-729-900-65 TRANSISTOR DTA144ES
D1013 8-719-024-99 DIODE 11ES2-NTA2B Q403 8-729-801-93 TRANSISTOR 2SD1387
D1014 8-719-024-99 DIODE 11ES2-NTA2B
D1016 8-719-024-99 DIODE 11ES2-NTA2B Q406 8-729-900-80 TRANSISTOR DTC114ES
Q407 8-729-422-57 TRANSISTOR UN4111
D1017 8-719-024-99 DIODE 11ES2-NTA2B Q408 8-729-119-76 TRANSISTOR 2SA1175-HFE
D1018 8-719-024-99 DIODE 11ES2-NTA2B Q409 8-729-900-80 TRANSISTOR DTC114ES
D1021 8-719-024-99 DIODE 11ES2-NTA2B Q410 8-729-900-65 TRANSISTOR DTA144ES
D1022 8-719-024-99 DIODE 11ES2-NTA2B
D1023 8-719-011-05 DIODE UZ-27BS Q411 8-729-900-65 TRANSISTOR DTA144ES
Q412 8-729-900-65 TRANSISTOR DTA144ES
D1069 8-719-987-63 DIODE 1N4148M Q820 8-729-422-57 TRANSISTOR UN4111
D1096 8-719-987-63 DIODE 1N4148M
D1097 8-719-024-99 DIODE 11ES2-NTA2B Q902 8-729-119-78 TRANSISTOR 2SC403SP-51
Q951 8-729-119-78 TRANSISTOR 2SC403SP-51
D1098 8-719-024-99 DIODE 11ES2-NTA2B Q952 8-729-119-78 TRANSISTOR 2SC403SP-51
D1099 8-719-024-99 DIODE 11ES2-NTA2B Q953 8-729-141-26 TRANSISTOR 2SC3622A-LK
D1201 8-719-987-63 DIODE 1N4148M Q954 8-729-141-26 TRANSISTOR 2SC3622A-LK
D1202 8-719-987-63 DIODE 1N4148M
D1204 8-719-987-63 DIODE 1N4148M Q1001 8-729-118-01 TRANSISTOR 2SB1116
Q1002 8-729-900-36 TRANSISTOR DTC124ES
D1205 8-719-987-63 DIODE 1N4148M Q1003 8-729-021-82 TRANSISTOR 2SD2396K
D1230 8-719-987-63 DIODE 1N4148M Q1006 8-729-030-19 TRANSISTOR 2SB1640
D1250 8-719-028-23 DIODE D3SBA20-4101 Q1201 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
D1251 8-719-987-63 DIODE 1N4148M
D1309 8-719-987-63 DIODE 1N4148M Q1204 8-729-900-63 TRANSISTOR DTA124ES
Q1205 8-729-900-36 TRANSISTOR DTC124ES
D1310 8-719-987-63 DIODE 1N4148M Q1206 8-729-900-80 TRANSISTOR DTC114ES
Q1207 8-729-119-76 TRANSISTOR 2SA1175-HFE
< FUSE > Q1208 8-729-119-76 TRANSISTOR 2SA1175-HFE
! F1601 1-532-504-31 FUSE,TIME-LAG (4A / 250V) Q1251 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA

! F1602 1-532-504-31 FUSE,TIME-LAG (4A / 250V)
< IC >
IC200 8-749-923-04 IC TOTX178 (CD DIGITAL OUT OPTICAL) The components identified by
IC201 8-759-822-09 IC LB1641 mark ! or dotted line with mark !
specified.
— 84 —
MAIN
< RESISTOR > R703 1-249-437-11 CARBON 47K 5% 1/4W
R704 1-249-429-11 CARBON 10K 5% 1/4W
R201 1-249-415-11 CARBON 680 5% 1/4W
R202 1-249-435-11 CARBON 33K 5% 1/4W R705 1-249-429-11 CARBON 10K 5% 1/4W
R203 1-249-425-11 CARBON 4.7K 5% 1/4W R708 1-249-429-11 CARBON 10K 5% 1/4W
R715 1-249-429-11 CARBON 10K 5% 1/4W
R208 1-249-425-11 CARBON 4.7K 5% 1/4W
R209 1-249-413-11 CARBON 470 5% 1/4W R716 1-247-807-31 CARBON 100 5% 1/4W
R252 1-249-435-11 CARBON 33K 5% 1/4W R724 1-247-807-31 CARBON 100 5% 1/4W
R725 1-247-807-31 CARBON 100 5% 1/4W
R301 1-249-430-11 CARBON 12K 5% 1/4W
R730 1-247-807-31 CARBON 100 5% 1/4W
R306 1-247-840-00 CARBON 2.4K 5% 1/4W
R308 1-249-421-11 CARBON 2.2K 5% 1/4W R732 1-247-807-31 CARBON 100 5% 1/4W
R735 1-247-807-31 CARBON 100 5% 1/4W
R351 1-249-430-11 CARBON 12K 5% 1/4W
R355 1-249-417-11 CARBON 1K 5% 1/4W R738 1-249-427-11 CARBON 6.8K 5% 1/4W
R740 1-249-415-11 CARBON 680 5% 1/4W
R357 1-249-433-11 CARBON 22K 5% 1/4W (JE)
R358 1-249-421-11 CARBON 2.2K 5% 1/4W
R360 1-249-417-11 CARBON 1K 5% 1/4W (AEP,UK)
R401 1-249-425-11 CARBON 4.7K 5% 1/4W R740 1-249-427-11 CARBON 6.8K 5% 1/4W
(G)
R403 1-249-425-11 CARBON 4.7K 5% 1/4W (EE)
R405 1-249-437-11 CARBON 47K 5% 1/4W (EA4,TH)
(JE)
R407 1-249-437-11 CARBON 47K 5% 1/4W
R409 1-249-429-11 CARBON 10K 5% 1/4W (AEP,UK,G)
R411 1-247-866-11 CARBON 30K 5% 1/4W (EE)
R741 1-249-429-11 CARBON 10K 5% 1/4W
R412 1-249-429-11 CARBON 10K 5% 1/4W (EA4,TH)
R415 1-249-429-11 CARBON 10K 5% 1/4W
R746 1-249-429-11 CARBON 10K 5% 1/4W
R420 1-249-429-11 CARBON 10K 5% 1/4W
R752 1-247-807-31 CARBON 100 5% 1/4W
R457 1-249-427-11 CARBON 6.8K 5% 1/4W
R759 1-247-807-31 CARBON 100 5% 1/4W
— 85 —
MAIN
R780 1-249-425-11 CARBON 4.7K 5% 1/4W
(IA) R1021 1-249-409-11 CARBON 220 5% 1/4W
R1201 1-249-417-11 CARBON 1K 5% 1/4W
R826 1-249-441-11 CARBON 100K 5% 1/4W
R1206 1-249-425-11 CARBON 4.7K 5% 1/4W
R872 1-249-441-11 CARBON 100K 5% 1/4W
R882 1-249-441-11 CARBON 100K 5% 1/4W ! R1209 1-212-881-11 FUSIBLE 100 5% 1/4W F
R901 1-249-421-11 CARBON 2.2K 5% 1/4W ! R1210 1-208-602-11 WIREWOUND 0.22 10% 2W F
R1211 1-249-417-11 CARBON 1K 5% 1/4W
R905 1-249-441-11 CARBON 100K 5% 1/4W
R1216 1-249-421-11 CARBON 2.2K 5% 1/4W
R910 1-249-429-11 CARBON 10K 5% 1/4W
R913 1-249-429-11 CARBON 10K 5% 1/4W R1220 1-249-389-11 CARBON 4.7 5% 1/4W
(AEP,UK,G,EE)
R915 1-249-441-11 CARBON 100K 5% 1/4W (AEP,UK,G,EE)
R917 1-247-903-00 CARBON 1M 5% 1/4W R1222 1-249-409-11 CARBON 220 5% 1/4W
R918 1-249-431-11 CARBON 15K 5% 1/4W
! R1226 1-215-868-00 METAL OXIDE 680 5% 1W F
R935 1-249-437-11 CARBON 47K 5% 1/4W (EXCEPT AEP,UK,G,EE)
R938 1-247-807-31 CARBON 100 5% 1/4W
R1233 1-249-426-11 CARBON 5.6K 5% 1/4W
R951 1-249-421-11 CARBON 2.2K 5% 1/4W
R1238 1-249-419-11 CARBON 1.5K 5% 1/4W
R952 1-249-421-11 CARBON 2.2K 5% 1/4W (EXCEPT IA)
R956 1-247-895-00 CARBON 470K 5% 1/4W (IA)
(EXCEPT EA4,TH) R1240 1-249-438-11 CARBON 56K 5% 1/4W
R961 1-249-421-11 CARBON 2.2K 5% 1/4W (AEP,UK,G,EE)
R1252 1-249-437-11 CARBON 47K 5% 1/4W
R964 1-249-437-11 CARBON 47K 5% 1/4W
R967 1-247-903-00 CARBON 1M 5% 1/4W R1254 1-249-437-11 CARBON 47K 5% 1/4W
R970 1-247-903-00 CARBON 1M 5% 1/4W R1256 1-249-425-11 CARBON 4.7K 5% 1/4W
R1257 1-249-425-11 CARBON 4.7K 5% 1/4W
R1001 1-249-421-11 CARBON 2.2K 5% 1/4W
R1002 1-249-409-11 CARBON 220 5% 1/4W The components identified by
R1003 1-249-417-11 CARBON 1K 5% 1/4W mark ! or dotted line with mark !
specified.
— 86 —
MAIN PANEL
R1258 1-249-425-11 CARBON 4.7K 5% 1/4W < CAPACITOR >
! R1259 1-212-881-11 FUSIBLE 100 5% 1/4W F
! R1260 1-208-602-11 WIREWOUND 0.22 10% 2W F C513 1-162-294-31 CERAMIC 0.001uF 10% 50V
R1261 1-249-417-11 CARBON 1K 5% 1/4W C514 1-124-589-11 ELECT 47uF 20% 16V
R1262 1-249-431-11 CARBON 15K 5% 1/4W C515 1-164-159-11 CERAMIC 0.1uF 50V
C522 1-162-306-11 CERAMIC 0.01uF 20% 16V
R1264 1-249-429-11 CARBON 10K 5% 1/4W
R1266 1-249-429-11 CARBON 10K 5% 1/4W C532 1-164-159-11 CERAMIC 0.1uF 50V
R1267 1-249-429-11 CARBON 10K 5% 1/4W (AEP,UK,G,EE)
R1268 1-249-397-11 CARBON 22 5% 1/4W < CONNECTOR >

R1269 1-249-397-11 CARBON 22 5% 1/4W
R1270 1-249-389-11 CARBON 4.7 5% 1/4W * CN501 1-568-854-11 SOCKET, CONNECTOR 11P
(AEP,UK,G,EE)
R1271 1-249-389-11 CARBON 4.7 5% 1/4W < DIODE >
(AEP,UK,G,EE)
R1272 1-249-409-11 CARBON 220 5% 1/4W D579 8-719-058-03 DIODE SEL5423E-TP15 (TUNER/BAND)
(EXCEPT EA4,TH)
R1273 1-249-409-11 CARBON 220 5% 1/4W D579 8-719-062-86 DIODE SEL5420 (TUNER/BAND) (EA4,TH)
R1281 1-249-439-11 CARBON 68K 5% 1/4W D580 8-719-812-44 DIODE TLO124 (EFFECT ON/OFF)
(EXCEPT AEP,UK,G,EE) D581 8-719-033-06 DIODE SEL5920A (GROOVE)
R1290 1-249-437-11 CARBON 47K 5% 1/4W D583 8-719-056-12 DIODE SML79420C-TP4 (fl)
R1295 1-249-433-11 CARBON 22K 5% 1/4W (EXCEPT EA4,TH,IA)
R1296 1-249-421-11 CARBON 2.2K 5% 1/4W
(EXCEPT AEP,UK,G,EE) D583 8-719-056-13 DIODE SML79423C-TP15 (fl) (EA4,TH,IA)
D585 8-719-033-06 DIODE SEL5920A (P PAUSE)
R1299 1-249-389-11 CARBON 4.7 5% 1/4W D586 8-719-812-44 DIODE TLO124 (r REC)
(AEP,UK,G,EE) D587 8-719-058-03 DIODE SEL5423E-TP15 (· ) (EXCEPT EA4,TH)
R1303 1-249-427-11 CARBON 6.8K 5% 1/4W D587 8-719-032-86 DIODE SEL5420E (·) (EA4,TH)
R1304 1-249-427-11 CARBON 6.8K 5% 1/4W
! R1601 1-219-124-11 FUSIBLE 0.68 5% 1/4W F D588 8-719-058-03 DIODE SEL5423E-TP15 (ª) (EXCEPT EA4,TH)
! R1602 1-219-121-11 FUSIBLE 0.22 5% 1/4W F D588 8-719-032-86 DIODE SEL5420E (ª) (EA4,TH)
D589 8-719-058-03 DIODE SEL5423E-TP15 (·) (EXCEPT EA4,TH)
! R1603 1-219-121-11 FUSIBLE 0.22 5% 1/4W F D589 8-719-032-86 DIODE SEL5420E (·) (EA4,TH)
D590 8-719-058-03 DIODE SEL5423E-TP15 (ª) (EXCEPT EA4,TH)
< VARIABLE RESISTOR >
D590 8-719-032-86 DIODE SEL5420E (ª) (EA4,TH)
RV301 1-238-600-11 RES, ADJ, CARBON 10K D601 8-719-033-06 DIODE SEL5920A (CD)
RV351 1-238-600-11 RES, ADJ, CARBON 10K D611 8-719-033-06 DIODE SEL5920A (TUNER)
D621 8-719-033-06 DIODE SEL5920A (TIMER)
< RELAY >
< FILTER >
RY1201 1-515-920-11 RELAY (24V)
FL501 1-517-489-11 INDICATOR TUBE, FLUORESCENT (EA4,TH,IA)
< TERMINAL > FL501 1-517-660-11 INDICATOR TUBE, FLUORESCENT
(EXCEPT EA4,TH,IA)
TM1201 1-537-240-31 TERMINAL BOARD (CHECKER PIN)(SPEAKER)
(EXCEPT AEP,UK,G,EE) < IC >
TM1201 1-537-801-11 TERMINAL BOARD (SPEAKER) (AEP,UK,G,EE)
IC501 8-759-448-36 IC uPD78042FGF-027-3B9
< VIBRATOR > IC502 8-759-332-18 IC GP1U27XB
X701 1-579-175-11 VIBRATOR, CERAMIC (10MHz) < COIL >

X702 1-567-098-41 VIBRATOR, CRYSTAL (32.768KHz)
************************************************************ * L510 1-410-858-21 INDUCTOR 0uH (AEP,UK,G,EE)
* A-4392-573-A PANEL BOARD, COMPLETE (RX50) < TRANSISTOR >

* A-4392-581-A PANEL BOARD, COMPLETE
(E,EA3,MY,SP,HK,TW,JE) Q501 8-729-119-78 TRANSISTOR 2SC403SP-51
* A-4392-589-A PANEL BOARD, COMPLETE (IA) Q502 8-729-119-76 TRANSISTOR 2SA1175-HFE
* A-4392-595-A PANEL BOARD, COMPLETE (EA4,TH) Q503 8-729-119-76 TRANSISTOR 2SA1175-HFE
******************************* Q504 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q507 8-729-119-76 TRANSISTOR 2SA1175-HFE
* 4-978-168-01 HOLDER, FL TUBE (EA4,TH,IA)
* 4-978-168-11 HOLDER, FL TUBE (EXCEPT EA4,TH,IA) Q508 8-729-119-76 TRANSISTOR 2SA1175-HFE
* 4-932-810-11 CUSHION (FL) Q509 8-729-119-76 TRANSISTOR 2SA1175-HFE

specified.
— 87 —
PANEL
Q510 8-729-119-76 TRANSISTOR 2SA1175-HFE R565 1-249-429-11 CARBON 10K 5% 1/4W

R570 1-249-437-11 CARBON 47K 5% 1/4W
< RESISTOR > R571 1-249-429-11 CARBON 10K 5% 1/4W
R572 1-249-429-11 CARBON 10K 5% 1/4W
R500 1-249-419-11 CARBON 1.5K 5% 1/4W
R501 1-249-401-11 CARBON 47 5% 1/4W R573 1-249-429-11 CARBON 10K 5% 1/4W
R577 1-247-903-00 CARBON 1M 5% 1/4W
R505 1-249-419-11 CARBON 1.5K 5% 1/4W
R583 1-247-807-31 CARBON 100 5% 1/4W
R510 1-249-407-11 CARBON 150 5% 1/4W
R588 1-247-807-31 CARBON 100 5% 1/4W
R519 1-249-407-11 CARBON 150 5% 1/4W
R621 1-249-403-11 CARBON 68 5% 1/4W
R524 1-249-415-11 CARBON 680 5% 1/4W
R651 1-249-421-11 CARBON 2.2K 5% 1/4W
R529 1-249-427-11 CARBON 6.8K 5% 1/4W
R532 1-249-401-11 CARBON 47 5% 1/4W
R533 1-249-413-11 CARBON 470 5% 1/4W < SWITCH >
R534 1-249-409-11 CARBON 220 5% 1/4W S500 1-554-303-21 SWITCH, TACTILE (POWER)
R535 1-249-411-11 CARBON 330 5% 1/4W S501 1-554-303-21 SWITCH, TACTILE (LOOP)
R536 1-249-413-11 CARBON 470 5% 1/4W S502 1-554-303-21 SWITCH, TACTILE (§ OPEN/CLOSE)
R537 1-249-415-11 CARBON 680 5% 1/4W S503 1-554-303-21 SWITCH, TACTILE (p)
R538 1-249-417-11 CARBON 1K 5% 1/4W S504 1-554-303-21 SWITCH, TACTILE (fl)
R539 1-249-419-11 CARBON 1.5K 5% 1/4W S505 1-554-303-21 SWITCH, TACTILE (TIMER)
R540 1-249-421-11 CARBON 2.2K 5% 1/4W S506 1-554-303-21 SWITCH, TACTILE (DISPLAY)
R541 1-247-843-11 CARBON 3.3K 5% 1/4W S507 1-554-303-21 SWITCH, TACTILE
R542 1-249-425-11 CARBON 4.7K 5% 1/4W (MULTI FUNCTION CONTROL 1)
R543 1-247-807-31 CARBON 100 5% 1/4W S508 1-554-303-21 SWITCH, TACTILE
(MULTI FUNCTION CONTROL 2)
R545 1-247-807-31 CARBON 100 5% 1/4W (MULTI FUNCTION CONTROL 3)
R546 1-247-807-31 CARBON 100 5% 1/4W
R548 1-247-807-31 CARBON 100 5% 1/4W (MULTI FUNCTION CONTROL 4)
S515 1-554-303-21 SWITCH, TACTILE (MENU 1)
R549 1-249-429-11 CARBON 10K 5% 1/4W S516 1-554-303-21 SWITCH, TACTILE (MENU 2)
R550 1-249-409-11 CARBON 220 5% 1/4W S517 1-554-303-21 SWITCH, TACTILE (MENU 3)
R551 1-249-437-11 CARBON 47K 5% 1/4W S519 1-554-303-21 SWITCH, TACTILE (P FILE)
R561 1-249-429-11 CARBON 10K 5% 1/4W
R562 1-249-429-11 CARBON 10K 5% 1/4W S520 1-554-303-21 SWITCH, TACTILE (EFFECT ON/OFF)
S521 1-554-303-21 SWITCH, TACTILE (SURROUND)
R563 1-249-401-11 CARBON 47 5% 1/4W S522 1-554-303-21 SWITCH, TACTILE (·)
R564 1-249-401-11 CARBON 47 5% 1/4W S523 1-554-303-21 SWITCH, TACTILE (ª)
— 88 —
PANEL TCB
S524 1-554-303-21 SWITCH, TACTILE ()) C41 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S525 1-554-303-21 SWITCH, TACTILE (p) C43 1-163-038-91 CERAMIC CHIP 0.1uF 25V
S526 1-554-303-21 SWITCH, TACTILE (0) C44 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S527 1-554-303-21 SWITCH, TACTILE (P PAUSE) C45 1-163-038-91 CERAMIC CHIP 0.1uF 25V
S528 1-554-303-21 SWITCH, TACTILE (r REC)
S529 1-554-303-21 SWITCH, TACTILE (CD SYNCHRO) C46 1-163-077-00 CERAMIC CHIP 0.1uF 10% 25V
C47 1-126-967-11 ELECT 47uF 20% 16V
S530 1-554-303-21 SWITCH, TACTILE (HIGH SPEED DUBBING) C48 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S533 1-554-303-21 SWITCH, TACTILE (TUNER/BAND) C49 1-126-959-11 ELECT 0.47uF 20% 50V
S534 1-554-303-21 SWITCH, TACTILE (FUNCTION) C50 1-126-960-11 ELECT 1.0uF 20% 50V
S535 1-554-303-21 SWITCH, TACTILE (GROOVE)
S536 1-554-303-21 SWITCH, TACTILE (DIRECTION) C51 1-126-960-11 ELECT 1.0uF 20% 50V
C52 1-126-963-11 ELECT 4.7uF 20% 50V
S537 1-554-303-21 SWITCH, TACTILE (DOLBY NR) (AEP,UK,G)
S538 1-554-303-21 SWITCH, TACTILE ()) C52 1-126-964-11 ELECT 10uF 20% 50V (EE)
S539 1-554-303-21 SWITCH, TACTILE (p) C53 1-126-964-11 ELECT 10uF 20% 50V
S540 1-554-303-21 SWITCH, TACTILE (0) C54 1-104-396-11 ELECT 10uF 20% 16V
S541 1-554-303-21 SWITCH, TACTILE (·)
C55 1-104-396-11 ELECT 10uF 20% 16V
S542 1-554-303-21 SWITCH, TACTILE (ª) C56 1-104-396-11 ELECT 10uF 20% 16V
< VIBRATOR > C58 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
X501 1-760-489-11 VIBRATOR, CERAMIC (5MHz) (AEP,UK,G)
************************************************************ C59 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V (EE)

* A-4303-514-A TCB BOARD, COMPLETE (AEP,UK) (AEP,UK,G)
* A-4303-515-A TCB BOARD, COMPLETE (G) C60 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V (EE)
* A-4303-516-A TCB BOARD, COMPLETE (EE) C61 1-126-301-11 ELECT 1uF 20% 50V
*************************************** C62 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
< CAPACITOR > C63 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V

C64 1-126-967-11 ELECT 47uF 20% 16V
C1 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V C65 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C2 1-126-967-11 ELECT 47uF 20% 16V C66 1-126-162-11 ELECT 3.3uF 20% 50V
C3 1-163-038-91 CERAMIC CHIP 0.1uF 25V C67 1-126-933-11 ELECT 100uF 20% 10V
C6 1-163-038-91 CERAMIC CHIP 0.1uF 25V C68 1-162-306-11 CERAMIC 0.01uF 30% 16V
C71 1-162-306-11 CERAMIC 0.01uF 30% 16V
C7 1-101-004-00 CERAMIC CHIP 0.01uF 50V (EE) C72 1-126-967-11 ELECT 47uF 20% 16V
C8 1-163-031-11 CERAMIC CHIP 0.01uF 50V C120 1-163-105-00 CERAMIC CHIP 33PF 5% 50V
C9 1-163-031-11 CERAMIC CHIP 0.01uF 50V (AEP,UK,G)
C11 1-216-295-91 CONDUCTOR, CHIP (2012) (G) < FILTER >
C16 1-163-038-91 CERAMIC CHIP 0.1uF 25V CF1 1-567-389-11 FILTER, CERAMIC
C19 1-163-249-11 CERAMIC CHIP 82PF 5% 50V CF2 1-760-393-11 FILTER, CERAMIC (AEP,UK,G)
(AEP, UK,EE) CF3 1-760-393-11 FILTER, CERAMIC (AEP,UK,G)
C21 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V CF3 1-567-389-11 FILTER, CERAMIC (EE)
C23 1-163-235-11 CERAMIC CHIP 22PF 5% 50V < CONNECTOR >
C24 1-163-239-11 CERAMIC CHIP 33PF 5% 50V * CN1 1-568-834-11 SOCKET, CONNECTOR 15P
C26 1-126-967-11 ELECT 47uF 20% 16V
C28 1-126-967-11 ELECT 47uF 20% 16V < DIODE >
C29 1-162-306-11 CERAMIC 0.01uF 30% 16V
C30 1-126-961-11 ELECT 2.2uF 20% 50V D21 8-719-976-99 DIODE DTZ5.1B
D41 8-719-016-74 DIODE 1SS352
C32 1-163-038-91 CERAMIC CHIP 0.1uF 25V < FRONTEND >
C34 1-163-091-00 CERAMIC CHIP 8PF 50V (G) FE1 1-233-542-11 FRONT END (4 GANG) (AEP,UK,G)
C34 1-163-229-11 CERAMIC CHIP 12PF 5% 50V FE1 1-693-335-11 FRONT END (3 GANG) (EE)
(AEP, UK,EE) FE2 1-233-514-11 ENCAPSULATED COMPONENT (AEP,UK,EE)
FE2 1-239-260-11 ENCAPSULATED COMPONENT (G)
C36 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V < IC >
C39 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V IC21 8-759-288-54 IC LC72130
C40 1-163-031-11 CERAMIC CHIP 0.01uF 50V IC41 8-759-176-03 IC LA1835
— 89 —
TCB
< IFT > < RESISTOR >
IFT41 1-409-636-11 TRANSFORMER, IF (CERAMIC FILTER) R1 1-249-401-11 CARBON 47 5% 1/4W

R2 1-216-037-00 METAL CHIP 330 5% 1/10W
< JUMPER RESISTOR > R3 1-216-037-00 METAL CHIP 330 5% 1/10W
R5 1-216-037-00 METAL CHIP 330 5% 1/10W
JR1 1-216-295-91 METAL CHIP 0 5% 1/10W R6 1-216-081-00 METAL CHIP 22K 5% 1/10W
(G)
JR2 1-216-295-91 METAL CHIP 0 5% 1/10W R7 1-216-037-00 METAL CHIP 330 5% 1/10W
(AEP,UK,EE) R8 1-216-037-00 METAL CHIP 330 5% 1/10W
JR3 1-216-295-91 METAL CHIP 0 5% 1/10W R9
(G) 1-216-081-00 METAL CHIP 22K 5% 1/10W
(AEP,UK,G) R11 1-216-081-00 METAL CHIP 22K 5% 1/10W
JR7 1-216-295-91 METAL CHIP 0 5% 1/10W
(G) R12 1-216-037-00 METAL CHIP 330 5% 1/10W
R13 1-216-037-00 METAL CHIP 330 5% 1/10W
JR8 1-216-295-91 METAL CHIP 0 5% 1/10W R14 1-216-081-00 METAL CHIP 22K 5% 1/10W
(AEP,UK,EE) R18 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR9 1-216-295-91 METAL CHIP 0 5% 1/10W (AEP,UK,EE)
(AEP,UK,EE) R19 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR45 1-216-295-91 METAL CHIP 0 5% 1/10W (AEP,UK,EE)
JR46 1-216-296-91 METAL CHIP 0 5% 1/8W
JR47 1-216-295-91 METAL CHIP 0 5% 1/10W R21 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
R22 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
JR48 1-216-295-91 METAL CHIP 0 5% 1/10W R23 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
JR51 1-216-295-91 METAL CHIP 0 5% 1/10W R25 1-249-417-11 CARBON 1K 5% 1/4W
(AEP,UK,EE)
(AEP,UK,EE) R28 1-249-417-11 CARBON 1K 5% 1/4W
R29 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
< JUMPER RESISTOR > R31 1-216-025-91 METAL CHIP 100 5% 1/10W
R32 1-249-425-11 CARBON 4.7K 5% 1/4W
JW4 1-249-413-11 CARBON 470 5% 1/4W R33 1-249-425-11 CARBON 4.7K 5% 1/4W
(AEP,UK,G) R34 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
JW5 1-249-413-11 CARBON 470 5% 1/4W R35 1-216-214-00 METAL CHIP 4.7K 5% 1/8W
(AEP,UK,G)
R36 1-216-025-91 METAL CHIP 100 5% 1/10W
< COIL > R37 1-216-073-00 METAL CHIP 10K 5% 1/10W
R38 1-216-089-91 METAL CHIP 47K 5% 1/10W
L2 1-414-142-11 MICRO INDUCTOR 1uH (AEP,UK,G) R39 1-249-429-11 CARBON 10K 5% 1/4W
L3 1-410-521-11 MICRO INDUCTOR 100uH R42 1-216-073-00 METAL CHIP 10K 5% 1/10W
L4 1-410-515-11 INDUCTOR 33uH (AEP,UK,G)
L41 1-407-500-00 MICRO INDUCTOR 4.7mH (AEP,UK,EE) R43 1-216-042-00 METAL CHIP 510 5% 1/10W
L41 1-410-119-11 MICRO INDUCTOR (EL TYPE) 1mH (G) R44 1-216-013-00 METAL CHIP 33 5% 1/10W
R45 1-247-843-11 CARBON 3.3K 5% 1/4W
< FILTER > R46 1-216-073-00 METAL CHIP 10K 5% 1/10W
R47 1-216-097-91 METAL CHIP 100K 5% 1/10W
LPF41 1-239-845-11 FILTER, LOW PASS
LPF42 1-239-845-11 FILTER, LOW PASS R48 1-249-417-11 CARBON 1K 5% 1/4W
R49 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
< TRANSISTOR > R50 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R51 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
Q1 8-729-201-27 TRANSISTOR 2SC2715Y R53 1-249-429-11 CARBON 10K 5% 1/4W
Q2 8-729-201-27 TRANSISTOR 2SC2715Y
Q3 8-729-201-27 TRANSISTOR 2SC2715Y R55 1-216-162-00 METAL CHIP 33 5% 1/8W
Q4 8-729-201-27 TRANSISTOR 2SC2715Y5 R56 1-249-393-11 CARBON 10 5% 1/4W
Q5 8-729-424-08 TRANSISTOR UN2111 R91 1-216-295-91 METAL CHIP 0 5% 1/10W
(AEP,UK,EE)
Q9 8-729-216-22 TRANSISTOR 2SA1162-G (AEP,UK,EE) R92 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q11 8-729-421-22 TRANSISTOR UN2211 (AEP,UK,EE) (AEP,UK,EE)
Q12 8-729-421-22 TRANSISTOR UN2211 (AEP,UK,EE) R99 1-249-399-11 CARBON 33 5% 1/4W
Q13 8-729-421-22 TRANSISTOR UN2211 (AEP,UK,EE)
Q14 8-729-421-22 TRANSISTOR UN2211 (AEP,UK,EE) < VARIABLE RESISTOR >

— 90 —
TCB
< TERMINAL > C53 1-126-964-11 ELECT 10uF 20% 50V
C54 1-104-396-11 ELECT 10uF 20% 16V
TM1 1-537-488-11 TERMINAL BOARD (ANT) (ANTENNA) C55 1-104-396-11 ELECT 10uF 20% 16V
C56 1-104-396-11 ELECT 10uF 20% 16V
< VIBRATOR > C57 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
X21 1-760-549-11 VIBRATOR, CRYSTAL (4.5MHz) C58 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
X41 1-760-220-11 FILTER, CERAMIC C59 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
X42 1-527-981-00 FILTER, CERAMIC C60 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
X43 1-577-075-11 OSCILLATOR, CERAMIC (19KHz) C61 1-126-301-11 ELECT 1uF 20% 50V
**************************************************************
* A-4303-520-A TCB BOARD, COMPLETE (JE) C64 1-126-967-11 ELECT 47uF 20% 16V
******************** C65 1-163-031-11 CERAMIC CHIP 10000PF 50V
C66 1-126-162-11 ELECT 3.3uF 20% 50V
< CAPACITOR > C67 1-126-933-11 ELECT 100uF 20% 10V
C1 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V C68 1-162-306-11 CERAMIC 10000PF 20% 16V
C2 1-126-967-11 ELECT 47uF 20% 16V C71 1-162-306-11 CERAMIC 10000PF 20% 16V
C3 1-163-038-91 CERAMIC CHIP 100000PF 25V C72 1-126-967-11 ELECT 47uF 20% 16V
C5 1-163-031-11 CERAMIC CHIP 10000PF 50V
C6 1-163-038-91 CERAMIC CHIP 100000PF 25V < FILTER >
C7 1-101-004-00 CERAMIC 0.01uF 50V CF1 1-567-389-11 FILTER, CERAMIC

C8 1-163-031-11 CERAMIC CHIP 10000PF 50V CF3 1-567-389-11 FILTER, CERAMIC
C10 1-163-031-11 CERAMIC CHIP 10000PF 50V < CONNECTOR >
* CN1 1-568-834-11 SOCKET, CONNECTOR 15P
C15 1-136-162-00 METALIZED FILM 0.056uF 5% 50V < VARIABLE CAPACITOR >
C17 1-163-031-11 CERAMIC CHIP 10000PF 50V CV1 1-141-227-00 CAP, TRIMMER 20PF
C18 1-163-088-00 CERAMIC CHIP 5PF 50V CV2 1-141-227-00 CAP, TRIMMER 20PF
C21 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V < DIODE >

C23 1-163-235-11 CERAMIC CHIP 22PF 5% 50V D1 8-719-976-30 DIODE KV1560NT
C24 1-163-239-11 CERAMIC CHIP 33PF 5% 50V D21 8-719-976-99 DIODE DTZ5.1B
C26 1-126-967-11 ELECT 47uF 20% 16V D41 8-719-016-74 DIODE 1SS352
C28 1-126-967-11 ELECT 47uF 20% 16V < FRONT END >
C29 1-162-306-11 CERAMIC 10000PF 20% 16V
C30 1-126-961-11 ELECT 2.2uF 20% 50V FE1 1-163-251-11 FRONT END
C31 1-163-031-11 CERAMIC CHIP 10000PF 50V FE2 1-239-262-11 ENCAPSULATED COMPONENT
< IC >
C34 1-163-091-00 CERAMIC CHIP 8PF 50V IC21 8-759-288-54 IC LC72130
C35 1-163-038-91 CERAMIC CHIP 100000PF 25V IC41 8-759-176-03 IC LA1835
C37 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V < IFT >
C38 1-162-211-31 CERAMIC 33PF 5% 50V IFT41 1-409-636-11 TRANSFORMER, IF (CERAMIC FILTER)
C40 1-163-031-11 CERAMIC CHIP 10000PF 50V < JUMPER RESISTOR >
C42 1-163-038-91 CERAMIC CHIP 100000PF 25V JR45 1-216-295-91 METAL GLAZE 0 5% 1/10W
JR46 1-216-296-91 METAL GLAZE 0 5% 1/8W
C43 1-163-038-91 CERAMIC CHIP 100000PF 25V JR47
C44 1-163-031-11 CERAMIC CHIP 10000PF 50V 1-216-295-91
C45 1-163-038-91 CERAMIC CHIP 100000PF 25V METAL GLAZE 0 5% 1/10W
C46 1-163-077-00 CERAMIC CHIP 0.1uF 10% 25V JR48 1-216-295-91 METAL GLAZE 0 5% 1/10W
C47 1-126-967-11 ELECT 47uF 20% 16V JR49 1-216-296-91 METAL GLAZE 0 5% 1/8W
C48 1-163-031-11 CERAMIC CHIP 10000PF 50V JR50 1-216-295-91 METAL GLAZE 0 5% 1/10W
C49 1-126-959-11 ELECT 0.47uF 20% 50V JR51 1-216-295-91 METAL GLAZE 0 5% 1/10W
C52 1-126-964-11 ELECT 10uF 20% 50V JR54 1-216-295-91 METAL GLAZE 0 5% 1/10W
— 91 —
TCB TRANSFORMER
L1 1-410-521-11 MICRO INDUCTOR 100uH R42 1-216-073-00 METAL CHIP 10K 5% 1/10W
L3 1-410-521-11 MICRO INDUCTOR 100uH R43 1-216-042-00 METAL CHIP 510 5% 1/10W
L41 1-410-119-11 MICRO INDUCTOR (EL TYPE) 1mH R44 1-216-021-00 METAL CHIP 68 5% 1/10W
R45 1-247-843-11 CARBON 3.3K 5% 1/4W
< FILTER > R46 1-216-073-00 METAL CHIP 10K 5% 1/10W
LPF41 1-239-845-11 FILTER, LOW PASS R47 1-216-097-91 METAL CHIP 100K 5% 1/10W
LPF42 1-239-845-11 FILTER, LOW PASS R48 1-247-843-11 CARBON 3.3K 5% 1/4W
R49 1-216-061-00 METAL CHIP 3.3K 5% 1/4W
< TRANSISTOR > R50 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R51 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
Q1 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L
Q2 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L R53 1-249-429-11 CARBON 10K 5% 1/4W
Q3 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L R54 1-249-399-11 CARBON 33 5% 1/4W
Q4 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L R55 1-216-162-00 METAL CHIP 33 5% 1/10W
Q5 8-729-424-08 TRANSISTOR UN2111 R56 1-249-393-11 CARBON 10 5% 1/4W
R91 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
Q8 8-729-033-67 TRANSISTOR 2SK211-Y-TE85L
Q9 8-729-216-22 TRANSISTOR 2SA812-T1-M5M6 R92 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q10 8-729-216-22 TRANSISTOR 2SA812-T1-M5M6 R93 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q12 8-729-421-22 TRANSISTOR UN2211 R94 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q13 8-729-421-22 TRANSISTOR UN2211
< VARIABLE RESISTOR >
Q14 8-729-421-22 TRANSISTOR UN2211
< RESISTOR > RV42 1-238-600-11 RES, ADJ, CARBON 10K
R1 1-249-401-11 CARBON 47 5% 1/4W < TRANSFORMER >

R2 1-216-037-00 METAL CHIP 330 5% 1/10W
R3 1-216-037-00 METAL CHIP 330 5% 1/10W T1 1-409-505-11 COIL (ANT. SW3)
R5 1-216-037-00 METAL CHIP 330 5% 1/10W T2 1-402-960-11 COIL (OSC SW3)
R6 1-216-081-00 METAL CHIP 22K 5% 1/10W
< TERMINAL >
R7 1-216-037-00 METAL CHIP 330 5% 1/10W
R8 1-216-037-00 METAL CHIP 330 5% 1/10W TM1 1-537-238-21 TERMINAL BOARD (ANTENNA)
R9 1-216-081-00 METAL CHIP 22K 5% 1/10W
R10 1-216-037-00 METAL CHIP 330 5% 1/10W < VIBRATOR >
R11 1-216-081-00 METAL CHIP 22K 5% 1/10W
X21 1-760-549-11 VIBRATOR, CRYSTAL (4.5MHz)
R12 1-216-037-00 METAL CHIP 330 5% 1/10W X41 1-760-220-11 FILTER, CERAMIC
R13 1-216-037-00 METAL CHIP 330 5% 1/10W X42 1-527-981-00 FILTER, CERAMIC
R14 1-216-081-00 METAL CHIP 22K 5% 1/10W X43 1-577-075-11 OSCILLATOR, CERAMIC (19kHz)
R18 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R19 1-216-073-00 METAL CHIP 10K 5% 1/10W **************************************************************
R20 1-216-121-91 METAL CHIP 1.0M 5% 1/10W * 1-659-332-11 TRANSFORMER BOARD

R21 1-216-049-91 METAL CHIP 1.0K 5% 1/10W *****************
R22 1-216-049-91 METAL CHIP 1.0K 5% 1/10W
R23 1-216-049-91 METAL CHIP 1.0K 5% 1/10W 1-533-399-31 HOLDER, FUSE (EXCEPT AEP,UK,G,EE,EA4,TH)
R24 1-216-025-91 METAL CHIP 100 5% 1/10W
< CONNECTOR >
R25 1-249-417-11 CARBON 1K 5% 1/4W
R26 1-249-437-11 CARBON 47K 5% 1/4W * CN1600 1-564-525-11 PLUG, CONNECTOR 10P
R27 1-249-429-11 CARBON 10K 5% 1/4W CN1601 1-564-321-00 PIN, CONNECTOR 2P
R28 1-249-417-11 CARBON 1K 5% 1/4W
R29 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < FUSE >
R30 1-216-186-00 METAL CHIP 330 5% 1/8W ! F1603 1-532-503-31 FUSE,TIME-LAG (1.6A / 250V)
R31 1-216-025-91 METAL CHIP 100 5% 1/10W (E,EA3,MY,SP,HK,TW,IA,JE)
R32 1-249-425-11 CARBON 4.7K 5% 1/4W
R33 1-249-425-11 CARBON 4.7K 5% 1/4W < SWITCH >
R34 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
! VS1601 1-572-675-11 SWITCH, POWER VOLTAGE CHANGE
R35 1-216-214-00 METAL CHIP 4.7K 5% 1/8W (VOLTAGE SELECTOR)
R36 1-216-025-91 METAL CHIP 100 5% 1/10W (E,EA3,MY,SP,HK,TW,IA,JE)
R37 1-216-073-00 METAL CHIP 10K 5% 1/10W
R38 1-216-089-91 METAL CHIP 47K 5% 1/10W
R39 1-249-429-11 CARBON 10K 5% 1/4W

specified.
— 92 —
TRANSFORMER
< TRANSFORMER > *************
HARDWARE LIST
! T1601 1-431-127-11 TRANSFORMER,POWER (EXCEPT AEP,UK,G,EE) *************
! T1601 1-431-129-11 TRANSFORMER,POWER (AEP,UK,G,EE)
************************************************************ #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#2 7-685-872-09 SCREW +BVTT 3X8 (S)
MISCELLANEOUS #3 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
************* #4 7-621-775-00 SCREW +B 2.6X3
#5 7-621-255-15 SCREW +P 2X3
6 1-776-166-11 WIRE (FLAT TYPE) (19 CORE)
7 1-773-158-11 WIRE (FLAT TYPE) (21 CORE) (240mm) #6 7-685-131-19 SCREW +BTP 2.6X4 TYPE2, N-S
(EA4,TH) #7 7-685-534-19 SCREW +BTP 2.6X8 TYPE2, N-S
7 1-773-160-11 WIRE (FLAT TYPE) (21 CORE) (260mm) #8 7-621-775-10 SCREW +B 2.6X4
(EXCEPT EA4,TH) #9 7-623-921-01 RING, RETAINING, CAPSTAN
8 1-769-940-11 WIRE (FLAT TYPE) (11 CORE) (100mm) #10 7-685-533-19 SCREW +BTP 2.6X6 TYPE2, N-S
9 1-769-946-11 WIRE (FLAT TYPE) (11 CORE) (160mm)
#11 7-685-862-09 SCREW +BVTT 2.6X6 (S)
10 1-233-545-11 ENCAPSULATED COMPONENT (EA4,TH)
10 1-233-546-11 ENCAPSULATED COMPONENT
(E,EA3,MY,SP,HK,TW,IA)
11 1-751-086-11 WIRE (FLAT TYPE) (13 CORE) (EA4,TH)
(EXCEPT EA4,TH )
! 57 1-569-007-11 ADAPTOR, CONVERSION 2P (E,IA.JE)
! 57 1-569-008-11 ADAPTOR, CONVERSION 2P (EA3,MY,SP,TW)

! 57 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
203 1-452-719-11 MAGNET ASSY
! 251 8-848-387-01 OPTICAL PICK-UP KSS-213BA/S-N
! CNP1601 1-575-651-11 CORD, POWER (AEP,G,EE,EA,MY,SP,HK,TW)

! CNP1601 1-575-653-11 CORD, POWER (E,IA,JE)
! CNP1601 1-751-326-31 CORD, POWER (TH)
! CNP1601 1-751-520-21 CORD, POWER (UK)
! F1601 1-532-504-31 FUSE,TIME-LAG (4A / 250V)
! F1602 1-532-504-31 FUSE,TIME-LAG (4A / 250V)

! F1603 1-532-503-31 FUSE,TIME-LAG (1.6A / 250V)
(E,EA3,MY,SP,HK,TW,IA,JE)
FL501 1-517-489-11 INDICATOR TUBE, FLUORESCENT (EA4,TH,IA)
FL501 1-517-660-11 INDICATOR TUBE, FLUORESCENT
(EXCEPT EA4,TH,IA)
HP101 1-500-093-11 HEAD,MAGNETIC (PLAYBACK) (DECK A)
HRPE101 1-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE) (DECK B)

M1 X-3371-223-1 MOTOR ASSY (CAPSTAN)
M2 A-2004-410-A MOTOR ASSY, DC (TRIGGER)
M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
M102 X-4917-504-1 MOTOR ASSY (SLED)
M903 A-4604-363-A MOTOR (L)ASSY (LOADING)

S101 1-572-085-11 SWITCH, LEAF (LIMIT)
! T1601 1-431-127-11 TRANSFORMER,POWER (EXCEPT AEP,UK,G,EE)
! T1601 1-431-129-11 TRANSFORMER,POWER (AEP,UK,G,EE)
************************************************************

specified.
— 93 —
HCD-GR5/RX50
Sony Corporation 97C0974-1

9-960-912-11 Home A&V Products Company Printed in Japan © 1997.3
Published by ServIce and Safty
— 94 — Engeneering Dept.(Shibaura)

Service Manual: HCD-GR5/RX50

Uploaded by

Copyright:

Available Formats

Service Manual: HCD-GR5/RX50

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: HCD-GR5/RX50

Uploaded by

Copyright:

Available Formats

HCD-GR5/RX50

SERVICE MANUAL AEP Model

HCD-GR5/RX50 is the tuner, deck, CD

Flexible Circuit Board Repairing

Laser component in this product is capable of emitting radiation

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY MARK ! OR DOTTED

1. SERVICING NOTE .................................................... 5

4. MECHANICAL ADJUSTMENTS ......................... 11

8. ELECTRICAL PARTS LIST ....................................79

Insert a tapering driver into the

@ª ª / · (reverse side play /

@∞ #£ Tuner (E, EA, Hong Kong, Malaysia, Singapore,

3-1. FRONT PANEL

1 Remove the connectors

5 Remove the claws

3-2. TC MECHANISM DECK

2 Remove the claws

1 Push the EJECT button.

*Note: It will be easy to remove if you push

2 Knob (JOG) * Note 1 Knob (VOL) * Note

3-5. CD MECHANISM DECK

3 Remove the CD mechanism

Playback Level Adjustment (Deck A, Deck B)

Adjustment Location: Playback Head (Deck A) set

3. Mode: Playback 3. Mode: Playback

MAIN board MAIN board

Adjustment Location: AUDIO board Adjustment Location: MAIN board

Note: 1. As a front-end (FE1) is difficult to repair if faulty, replace

AM Tuned Level Adjustment

Procedure: Adjustment Location:

FM Tuned Level Adjustment

Adjustment Location: TCB board

Procedure: D1, CV2, T2

30% amplitude SPEAKER terminal

Set frequency Adjustment

• Repeat the procedures is each adjustment several times, and the

1.Connect oscilloscope to test point TP (RF) on BD board.

level: 1.3 ± 0.3 Vp-p

oscilloscope [BD BOARD] — Component Side —

level: 300 ± 100 mVp-p [MAIN BOARD] — Conductor Side —

6. Remove the lead wire connected in step 1.

Focus/Tracking Gain Adjustment (RV102, RV103)

This gain has a margin, so even if it is slightly off.

OPTICAL PICK-UP BLOCK CD X101

SLED / SPINDLE 2 OUT1 IN1 5 LOAD IN

J801 IC802 INPUT SELECTOR IC1201

XOUT 5 Q1001,1002 D1013

— TUNER SECTION — — TUNER SECTION — (Tourist MODEL)

Q12 23 VCO Q10

Q13 MW SW X43 MW SW 23 VCO

RV42 MUTE MUTE

• R CH :Same as L CH Abbreviation • R CH:Same as L CH

— DECK SECTION — 6-2. CIRCUIT BOARDS LOCATION

• R CH:Same as L CH S1001 (A PLAY)

S1009 LEAF SWITCH board

AUDIO board (including p A)

• IC501 GRAPHIC CONTROL (µPD78042FGF-027-3B9)

Pin No. Pin Name I/O Function