CFD-S22/S32

SERVICE MANUAL US Model

Ver 1.0 2000. 02
Canadian Model
E Model

Photo: CFD-S32 (Silver)

Model Name Using Similar Mechanism CFD-S38

CD CD Mechanism Type KSM-213CDM
Section
Optical Pick-up Name KSS-213C
TC Model Name Using Similar Mechanism CFD-S38
Section Tape Transport Mechanism Type MF-V10-117

SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US Model) Radio section
POWER OUTPUT AND TOTAL Frequency range
HARMONIC DISTORTION FM: 87.6 - 108 MHz
AM: 530 - 1,710 kHz
With 3.2-ohm loads, both channels driven from
Antennas
150 - 6,300 Hz; rated 1.8 W per channel- FM: Telescopic antennas
minimum RMS power, with no more than 10% AM: Built-in ferrite bar antennas
total harmonic distortion in AC operation.
Cassette-corder section
Recording system
Other Specifications 4-track 2 channel stereo
CD player section Fast winding time
System Approx. 120 sec. with Sony cassette C-60
Compact disc digital audio system Frequency response
Laser diode properties TYPE I (normal): 70 - 10,000 Hz
Material: GaAlAs
Wave length: 780 nm General
Emission duration: Continuous Speaker
Laser output: Less than 44.6 µW Full range: 10 cm (4 in.) dia.,
(This output is the value measured at a distance of 3.2 ohms, cone type (2)
about 200 mm from the objective lens surface on Outputs
the optical pick-up block with 7 mm aperture.) Headphones jack (stereo minijack)
Spindle speed For 16 - 68 ohms impedance headphones
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2 dB – Continued on next page –
Wow and flutter
Below measurable limit

CD RADIO CASSETTE-CORDER

–1–
Power output (excluding US model)
2.3 W + 2.3 W (at 3.2 ohms, 10 %) CAUTION
harmonic distortion in AC operation) Use of controls or adjustments or performance of proce-
Power requirements
dures other than those specified herein may result in haz-
For CD radio cassette-corder:
120 V AC, 60 Hz ardous radiation exposure.
9 V DC, 6 size D (R20) batteries
For remote control (CFD-S32 only):
3 V DC, 2 size AA (R6) batteries
Power consumption Flexible Circuit Board Repairing
AC 20 W • Keep the temperature of the soldering iron around 270˚C during
Battery life
repairing.
For CD radio cassette-corder:
FM recording • Do not touch the soldering iron on the same conductor of the
Sony R20P: approx. 13.5 h circuit board (within 3 times).
Sony alkaline LR20: approx. 20 h • Be careful not to apply force on the conductor when soldering
Tape playback or unsoldering.
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 15 h
Notes on Chip Component Replacement
CD playback
Sony R20P: approx. 2.5 h
• Never reuse a disconnected chip component.
Sony alkaline LR20: approx. 7 h
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Dimensions
Approx. 420 × 165 × 256 mm (w/h/d)
(16 5/8 × 6 1/2 × 10 1/8 inches) (incl. projecting parts) NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
Mass OR BASE UNIT
Approx. 4.1 kg (9 lb. 1 oz.) (incl. batteries)
Supplied accessories
The laser diode in the optical pick-up block may suffer electrostatic
AC power cord (1) breakdown because of the potential difference generated by the
Remote control RMT-CS32A (1) (CFD-S32 only) charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
Design and specifications are subject to change without
notice. the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

–2–
SAFETY CHECK-OUT TABLE OF CONTENTS

After correcting the original service problem, perform the following 1. SERVICING NOTES ......................................................... 4
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws, 2. GENERAL
and all other exposed metal parts for AC leakage. Check leakage as Location of controls ................................................................. 5
described below. Adjusting the sound emphasis (MEGA BASS/TONE) ........... 5
Playing a CD ........................................................................... 6
LEAKAGE TEST Listening to the radio ............................................................... 6
Playing a tape .......................................................................... 7
The AC leakage from any exposed metal part to earth ground and Recording ................................................................................ 7
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes). 3. DISASSEMBLY
Leakage current can be measured by any one of three methods. 3-1. Cabinet (Front) Sub Assy .................................................... 8
3-2. Wires ................................................................................... 9
1. A commercial leakage tester, such as the Simpson 229 or RCA 3-3. Secondary Board, Power Board .......................................... 9
WT-540A. Follow the manufacturers’ instructions to use these 3-4. Tuner Board ....................................................................... 10
instruments. 3-5. Cabinet (Upper) Block Assy ............................................. 10
3-6. Main Board ....................................................................... 11
2. A battery-operated AC milliammeter. The Data Precision 245 3-7. CD Mechanism Block ....................................................... 11
digital multimeter is suitable for this job. 3-8. Tape Mechanism Block ..................................................... 12
3-9. Holder Assy, Cassette ........................................................ 12
3. Measuring the voltage drop across a resistor by means of a VOM 3-10. TC Board ........................................................................... 13
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The 4. MECHANICAL ADJUSTMENTS ............................... 14
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A) 5. ELECTRICAL ADJUSTMENTS
Tape Section .......................................................................... 14
Tuner Section ......................................................................... 15
CD Section ............................................................................ 16
To Exposed Metal
Parts on Set 6. DIAGRAMS
6-1. IC Pin Description ............................................................. 17
6-2. Circuit Boards Location .................................................... 18
6-3. Block Diagram – CD Section – ......................................... 19
6-4. Block Diagram – Main Section – ...................................... 21
AC 6-5. Printed Wiring Board – Tuner Section – ........................... 23
0.15µF 1.5k Ω voltmeter
(0.75V) 6-6. Schematic Diagram – Tuner Section – .............................. 25
6-7. Printed Wiring Board – CD Section – ............................... 27
6-8. Schematic Diagram – CD Section –.................................. 29
6-9. Schematic Diagram – TC Section – .................................. 31
Earth Ground 6-10. Printed Wiring Boards – Main Section – .......................... 33
6-11. Schematic Diagram – Main Section (1/2) – ...................... 35
6-12. Schematic Diagram – Main Section (2/2) – ...................... 37
Fig. A. Using an AC voltmeter to check AC leakage. 6-13. Printed Wiring Board – Control Section – ........................ 39
6-14. Schematic Diagram – Control Section – ........................... 41
6-15. Printed Wiring Boards – Power Supply Section – ............ 43
6-16. Schematic Diagram – Power Supply Section – ................. 45

7. EXPLODED VIEWS
7-1. Cabinet (Front) Section ..................................................... 50
7-2. Cabinet (Rear) Section ...................................................... 51
7-3. Cabinet (Upper) Section .................................................... 52
7-4. Tape Mechanism Section-1 ............................................... 53
7-5. Tape Mechanism Section-2 ............................................... 54
7-6. Optical Pick-up Section .................................................... 55

8. ELECTRICAL PARTS LIST ......................................... 56

–3–
 SECTION 1
SERVICING NOTES
LASER DIODE AND FOCUS SEARCH OPERATION
CHUCK PLATE JIG ON REPAIRING
CHECK
On repairing CD section, playing a disc without the lid (CD), use 1. Turn ON the POWER button and press FUNCTION button to
Chuck Plate Jig. CD position.
• Code number of Chuck Plate Jig: X-4918-255-1 2. Open the lid (CD).
3. Turn on S501 with screwdriver, etc. as following figure.
4. Press the CD N X button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.

S501

–4–
SECTION 2
GENERAL This section is extracted
from instruction manual.

–5–
–6–
–7–
 SECTION 3
DISASSEMBLY
• The equipment can be removed using the following procedure.

Set Cabinet (Front) Sub Assy Wires Cabinet (Upper) Block Assy Main Board
Secondary, Power Board
Tuner Board

Tape Mechanism Block Holder Assy, Cassette

CD Mechanism Block TC Board

Note : Follow the disassembly procedure in the numerical order given.

3-1. CABINET (FRONT) SUB ASSY

9 cabinet (front) sub assy

6 BVTP 3x12

7 CNP323

lid (CD)

2 BVTP 3x10

8 CNP501

5 BVTP 3x10
1 lid, battery case
4 BVTP 3x12
3 BVTP 3x10

–8–
3-2. WIRES
Put flat cable and wires between the cabinets and push them in the
grooves located at A to G in the figure to prevent disconnection
before assembling the set.

CABINET (FRONT)

A B C D

E G

CABINET (REAR)

from speaker F

3-3. SECONDARY BOARD, POWER BOARD

5 CNP901

3 BVTP 3x10

SECONDARY board

6 POWER board

2 BVTP 3x10
1 BVTP 3x10

4 CNP902

–9–
3-4. TUNER BOARD

5 TUNER board

1 CNP1

3 holder (PWB)(TU)
2 BVTP 3x10

3-5. CABINET (UPPER) BLOCK ASSY

6 BVTP 3x12 3 holder assy, cassette

7 BVTP 3x12
4 lid (CD)
5 BVTP 3x10
8 BVTP 3x12

9 handle

0 cabinet (upper) block assy

cabinet (rear)

2 CNP902

1 CNP1

– 10 –
3-6. MAIN BOARD

2 BVTP 3x10 1 BVTP 3x10

8 MAIN board

5 CNP322
3 connector

4 CNP651

7 CNP502

6 CNP505

3-7. CD MECHANISM BLOCK

1 PWH 2.6x10
2 PWH 2.6x10

3 CD mechanism block

– 11 –
3-8. TAPE MECHANISM BLOCK

1 BVTP 3x10

2 BVTP 3x10

3 tape mechanism block

3-9. HOLDER ASSY, CASSETTE

1 BVTP 3x10

2 DAMPER

4 holder assy, cassette

– 12 –
3-10. TC BOARD

1 BVTP 2x4

2 TC board

3 Removal the solders.

– 13 –
 SECTION 4 SECTION 5
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
PRECAUTION TAPE SECTION 0 dB = 0.775 V
1. Clean the following parts with a denatured-alcohol-moistened
swab : • Standard Output Level
record/playback head pinch roller
Output terminal HP OUT
erase head rubber belts
capstan idlers load impedance 32 Ω
2. Demagnetize the record/playback head with a head demagne- output signal level 0.25 V (–10 dB)
tizer. (Do not bring the head magnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
• Test Tape
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted. Type Signal Used for
WS-48A 3 kHz, 0 dB tape speed adjustment
Torque Measurement
Mode Torque meter Meter reading Tape Speed Adjustment
Procedure:
30 – 70 g • cm
FWD CQ-102C Mode: playback
(0.42 – 0.97 oz • inch)
FWD CQ-102C 1.5 – 5.5 g • cm digital frequency
Back Tension (0.021 – 0.076 oz • inch) test tape
counter
WS-48A
more than 60 g • cm (3 kHz, 0 dB)
FF CQ-201B
(more than 0.83 oz • inch) 32 Ω
more than 60 g • cm
REW CQ-201B set
(more than 0.83 oz • inch)

Phones jack
Tape Tension Measurement
Mode Tension meter Meter Reading Adjust so that the value on the digital frequency counter is
more than 100 g 3,000 Hz.
FWD CQ-403A
(more than 3.53 oz)
Specification Value:
Digital frequency counter
2,910 to 3,090 Hz
Adjust so that the frequency at the beginning and that at the end of
tape winding are between 2,910 to 3,090 Hz.

Adjustment Location:

Tape speed adjustment

control inside motor

– 14 –
 TUNER SECTION 0 dB = 1 µV FM FREQUENCY COVERAGE
• FM Section ADJUSTMENT
Setting: Frequency Display 87.5 MHz 108 MHz
RADIO (BAND) button: FM
Reading on Digital voltmeter 1.6 ± 0.4 V 4.0 ± 0.3V
FM RF signal Adjustment Part <confirmation> L2
generator
TP (JW2) FM TRACKING ADJUSTMENT
0.01 µF Adjust for a maximum reading on level meter.
set L1 CT1
75 kHz frequency 87.5 MHz 108 MHz
deviation by 1 kHz signal
output level : as low as possible
AM FREQUENCY COVERAGE
ADJUSTMENT
• AM Section Frequency Display 530 kHz 1,710 kHz
Setting: Reading on Digital voltmeter 1.1 ± 0.1 V 5.2 ± 0.8V
RADIO (BAND) button: AM Adjustment Part L4 <confirmation>
AM RF signal
generator AM TRACKING ADJUSTMENT
Put the lead-wire
antenna close to Adjust for a maximum reading on level meter.
the set. L3 CT3
620 kHz 1,400 kHz
30% amplitude
modulation by • For AM adjustment, fix the ferrite-rod antenna (L3) as shown
400 Hz signal below and then perform tracking adjustment at L4 and CT3.
Lastly check the voltage.

• Connecting Level Meter (FM and AM)

level meter
(range: 0.5–5 V ac)
32 Ω

set

i jack (J321)

• Connecting Digital Voltmeter (FM and AM)

digital
voltmeter

100 kΩ
TP (VT)

• Repeat the procedures in each adjustment several times, and the

frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.

– 15 –
Adjustment Location:

ANT1
FM
TELESCOPIC
ANTENNA

– tuner board (component side) – – tuner board (conductor side) –

JW2

FM L1
TRACKING
ADJUSTMENT CT1

IC1

L2
FM
FREQUENCY
COVERAGE
ADJUSTMENT TP TP
TP(VT)
(VT) (VT)

AM L3
TRACKING L4
ADJUSTMENT CT3 IC2

CNP1

CD SECTION
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.

FOCUS BIAS CHECK Test Point:

1. Connect the oscilloscope between IC701 pin qg (TP RFO) and
– CD board (conductor side) –
GND on CD board.
2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)
3. Press the CD N X button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape ( ) in the
center of the waveform can be clearly distinguished.
TP TP
(RF)
• RF signal reference waveform (eye pattern) (RF)

VOLT/DIV : 200 mV (10 : 1 probe in use)

TIME/DIV : 500 nS

RF level :
1.2 ± 0.3 Vp-p

When observing the eye pattern, set the oscilloscope for AC range
and raise vertical sensitivity.

– 16 –
 SECTION 6
DIAGRAMS
6-1. IC PIN DESCRIPTION Pin No. Pin Name I/O Pin Description
• IC501 CXP83620-022Q (SYSTEM CONTROL) 75 NC — Not used. (Open)
Pin No. Pin Name I/O Pin Description 76 A-MUTE O Audio mute output H: Mute
1 C-SCOR I CD SCOR input 77 SCL O EEPROM clock output
2 RMC I Sircs receiver input 78 EC I Event counter input
3 MUTE O MUTE output H: Mute 79 TC-PLAY I Tape play switch input L: Tape
4 ADJ O F TEX frequency division output 80 C-DOOR I CD door open/close switch input L: Close
5 C-SCLK O CD SENSE read clock output
6 C-SENS I CD SENSE input
7 C-SQCK O CD Sub-Q read clock output
6-2. CIRCUIT BOARDS LOCATION
8 C-SQSO I CD Sub-Q data input
9 C-XRST O CD system reset output
10 C-CLOCK O CD system clock output
SECONDARY board
11 C-LATCH O CD system latch output POWER board
12 C-DATA O CD command data output
BATTERY board
13 C-AGCCONT O CD AGC control output
14 R-COUNT I Tuner PLL data input TC board
15 R-CLOCK O Tuner PLL clock output MAIN board
16 R-DATA O Tuner PLL data output
17 R-LATCH O Tuner PLL latch output CD board
18 V-LATCH O Volume latch output Not used. (Open)
19 V-DATA O Volume data output
20 V-CLOCK O Volume clock output
21 P-CON O System power control output H: PCON
22 REG CHK I Regulator check signal input
23 REC I Tape record signal input H: REC
24 SDA I/O EEPROM input/output CONTROL board
25 – 28 KEY-1 – 4 I Key input HALF BATTERY board
29 MODE CHECK I Mode set input
30 RST I System reset input
31 EXTAL I Oscillation input (4.19 MHz) LCD board
TUNER board
32 XTAL O Oscillation output (4.19 MHz)
33 VSS — GND
34 VL O LCD drive port ON/OFF output
35 – 37 VLC3 – 1 O LCD drive voltage output
38 – 41 COM0 – 3 O LCD drive common output
42 – 58 SEG0 – 16 O LCD drive segment output
59 SEG17 O LCD drive segment output Not used. (Open)
60, 61 NC — Not used. (Open)
62 INIT O Initial set signal output
63 TONE O TONE control output L: TONE
64 MEGA BASS O MEGA BASS control output H: MEGA BASS
65 BT-CHK I Battery check input H: BT-CHK
66 MT-CONT I MT control input H: MT-CONT
67 ISS1 O ISS1 output H: ISS1 Not used. (Open)
68 ISS2 O ISS2 output H: ISS2 Not used. (Open)
69 TAPE O Tape function output H: Tape
70 RADIO O Tuner function output H: Radio
71 CD O CD function output H: CD
72 VDD — Power supply pin (+3.3 V)
73 TX O Oscillation output (150 kHz)
74 TEX I Oscillation input (150 kHz)

– 17 – – 18 –
CFD-S22/S32

6-3. BLOCK DIAGRAM — CD SECTION —

CD BOARD MAIN BOARD (1/2)

SYSTEM SERVO PROCESSOR,
DIGITAL SIGNAL PROCESSOR
RF AMP IC702
ASYMMETRY CNP702(2/2) CNP502(2/2) CNP505(1/3)
CNP701 IC701 PWM
CORRECTION AOUT1 15 3 3 CD L
A 12
4
PD1 RFO
15 51
RFAC
& EFM DEMODULATOR OVER
SAMPLING
AMP 70 1
DIGITAL LOUT1
C 10 PLL DIGITAL 72
D/A FILTER
INTERFACE & AOUT2
B 11 PD2 SERIAL 77 CD R
5 INTERNAL
RFDC IN
43 BUS LOUT2
13 FE FE OPERATIONAL INTERFACE 75
D 13 39 PWM
TE AMPLIFIER
SE AMP
11 40 ANALOG SWITCH
7 LD POWER LD TE
LD 41 & SUB CODE
CONTROL 2
VC A/D PROCESSOR
Q701 38
PD 5 PD CE CONVERTER
3 42
VREF
SERVO
INTERFACE
E 14 E &
8 TF TFDR
30 SERVO AUTO
TR TRDR SERVO
F 9 F 31 DSP SEQUENCER
7 FF FFDR
32 &
16 FR FRDR PWM
VREF 33
SF SFDR GENERATOR CPU
VREF 10 VC 28 (US MODEL)
SR SRDR DIGITAL INTERFACE TIMING P. CONT
29
OPTICAL PICK-UP
BLOCK
LD ON LD ON
CLV LOGIC 2
SWITCH 19 EXCEPT US MODEL
(KSS-213C)

SQSO

SCOR
XLON

SQCK
SENS

DATA

XRST

XTAO
SSTP

SCLK
XLAT
MDP
Q702

XTAI
AGC CONT 18

CLK
POWER
26 27 14 8 1 2 20 5 6 7 9 3 66 67 VDD SWITCH
Q951
D955 D951 D952

3
TRACKING 13 T+ TRACKING TFDR
2
TF X701 POWER
2 COIL
COIL 14 T– TRDR
3
TR 16.9344MHz SWITCH
DRIVE VDD
Q952,953
4 FFDR FF
FOCUS 17 F+ FOCUS 24 CNP702(1/2) AUDIO
1 COIL FRDR FR
COIL 18 F– 23 3 6 13 12 4 9 8 7 5 11 6V REG
DRIVE VDD(SW) Q955
MUTE 20
COM
COM 3.3V 3.3V REG
M702
SF
SLED M 12 SL+ SLED SFDR
5 15 12 5 6 14 9 10 11 13 7
Q957
MOTOR
MOTOR 11 SL– SRDR
6
SR
DRIVE AUDIO 6V
CNP502(1/2)
M701
SPINDLE M 15 SP+ SPINDLE SPIN
MOTOR 25
MOTOR 16 SP–
DRIVE SECONDARY BOARD T901 POWER
POWER BOARD
EXCEPT CND MODEL
VREF F902 TRANSFORMER
SLED/SPINDLE
27 VREF CND MODEL CNJ901
MOTOR DRIVE,
AC IN
TRACKING/FOCUS
COIL DRIVE
IC703
D901 - 904
S702
(LIMIT)

13 6 8 7 1 12 11 10 5 9
C-AGC
CONT

C-SENS
C-SQSO
C-SQCK
C-SCOR

C-DATA
C-LATCH
C-CLOCK
C-SCLK
C-XRST
S501
CD DOOR 80 C-DOOR
OPEN/
VDD REG,AC CNB901(1/2)
CLOSE D511 CD
BATTERY
VDD(SW) CHECK 65 BT-CHK SYSTEM CONTROL
RADIO

Q501-504 IC501 (1/2) 1 1

66 MT-CONT 4.5V
CD

D509 DRY BATTERY

70 71 SIZE " D "
KH321 CNP902 (IEC DESIGNATION R20)
D956 6PCS,9V 4.5V
RADIO
3.3V REG
RA6V 6V REG AUDIO 6V 3.3V 3 2
• Signal path Q513,514
IC502 3 3
: CD VDD CNB901(2/2) CNP904
4 1
CD 1 1 3 3
R-ch : same as L-ch. CD3.3V 3.3V REG COM 3.3V 2
Q511,512 CNP901
AC-HI
3 2 2
Abbreviation HALF
CND : Canadian model BATTERY
BOARD BATTERY
04 BOARD

– 19 – – 20 –
 CFD-S22/S32

6-4. BLOCK DIAGRAM — MAIN SECTION —

TC BOARD MAIN BOARD (2/2)

R.RO
9
R.IN
8
R.LIN
CD R 14 VOLUME/SOUND CONTROL POWER AMP
DET REC/PB
PRE AMP CNP301 CNP505 IC302 IC304
CNP301(1/3) IC301 (3/3) (3/3) R-CH
L.RO J321
4 ALC 2 LINE
CD L 3 L.LIN L.LO 6 6 VIN2 VOUT2
1 24 20 AMP
Q121
8 7 11 5 i
HRP301
RECORD/PLAYBACK
HEAD L.IN MEGA MUTE
5 R.LO 18 R-CH BASS Q124
L-CH LOGIC CONTROL SP301
RADIO L 8 CONTROL
8 Q122 EEPROM SPEAKER
LINE 17 CD3.3V
R-CH IC504 (L-CH)
6 REF
LPF SP302

CLOCK
R.RAD
L.RAD

DATA
Q123 SPEAKER

REC
HE301 TAPE 15 5 SDA
ERASE HEAD S301 6 SCL (R-CH)
-1 -2 21 22 16 5 4 (S32)
(REC/PB)
REC
R-CH

PB T301 P.CONT CNP322

2 VDD(SW) 1 S304
REC BIAS OSC 2 (TAPE PLAY)
TAPE
Q301 3
CNP301(2/3) SWITCH
10 5 1 9 Q997 4

M
10 5 1 9
M301
CNP505(2/3) CAPSTAN/REEL
AUDIO 6V MOTOR
23 69 20 19 64 63 76 24 77 21 79
SYSTEM CONTROL

TAPE

V-CLOCK
V-DATA

MEGA BASS

TONE

A-MUTE

SDA
SCL

P-CON

TC-PLAY
REC

MODE CHECK
TUNER
IC501 (2/2)

R-COUNT
R-CLOCK

REG CHK
R-LATCH
R-DATA

EXTAL
SEG16

MUTE
COM0

COM3
SEG0

XTAL

KEY1

KEY4

RMC
RST

INIT
TEX
VOL
|

|
TX
38–41 42–58 17 16 15 14 73•74 31 32 30 3 25–28 2 62 29 22

CNP551 (S32)
1-4 5-21 1 CNP501
X501 MODE
RESET IF REQ 2-5 7 D510
21-18 17-1 4.19MHz SWITCH
CNP651 IC503 Q510
Q507
2
2-5 7
LIQUID CRYSTAL X502
DISPLAY PANEL 150kHz CNP601
3.3V 1
LCD501
REMOTE VDD (SW)
6 6
LCD BOARD CONTROL MODE
KH503 IC601
1 KH504 5 4 3 2 1
S601-604
SWITCH
3 CONTROL
S607-626 Q505,506
S605,627 (S32) (S32) D601
6 7 8 9 10 11 OPR/BATT
S606 (S22)
CNP1 REMOTE
8 8 CONTROL AC-HI
TUNER BOARD REG 3
1 2 3 4 Q509
PLL
CE
DI
CL
DO

IC2 (S32)

ST-IND
MO/ST
AM IN
FM IN

BAND
XOUT

18 LP-OUT
IF IN
XIN

CONTROL BOARD
L4 11 12 20 19 13 10 7 8

X1
75kHz
L4 RA6V 20 19 14 17 13 18
AM AM OSC FM/AM FRONT-END, IF DET, IF-OUT
OSC-OUT

LPF2/MO-ST

LPF1/BAND

ST-IND

D3 FREQUENCY
FM STEREO DEMODULATOR IF CUT
COVERAGE IC1
L3 AM
IF
AM OSC
BUFFER
ANT1 FERRITE-ROD AM
FM ANTENNA
AM
RF-IN AM
MIX-OUT T1
CF4 IF-IN AM
Signal path
22 4 6
TELESCOPIC
ANTENNA
MIX DET : FM
R-OUT
FM AF DET-OUT
16 15
MPX-IN FM 11 R-CH : AM
BUFFER MPX MUTE L-OUT
CT3
FM
MIX
FM
12 : TAPE PLAY
RA6V RA6V
RF-IN
FM 7
IF-IN FM : TAPE REC
2 DET IF CUT
OSC
CF2 : CD
QUAD

FM
CT3,L3 RF-OUT FM OSC
AM 24 21 RA6V 10
TRACKING D1 D2 R-ch : same as L-ch.
L1 CT1 L2 L2 T2
CT1,L1 FM
FM FREQUENCY
TRACKING RA6V RA6V COVERAGE
RA6V

04

– 21 – – 22 –
CFD-S22/S32

6-5. PRINTED WIRING BOARD — TUNER SECTION — • Refer to page 18 for Circuit Boards Location.

1 2 3 4 5 6 7

• Semiconductor
Location

B Ref. No.
D1
Location
E-4
D2 E-4
D3 F-4
D10 B-3
D11 B-3

IC1 D-5
C IC2 H-5

F
TP(VT)

I
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• f : internal component.
• b : Pattern from the side which enables seeing.

J
04
(Page 34) (Page 33)

– 23 – – 24 –
 CFD-S22/S32

6-6. SCHEMATIC DIAGRAM — TUNER SECTION — • Refer to page 47 for IC Block Diagrams.

(Page 36)

(Page 36)

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF • Voltage and waveforms are dc with respect to ground
50 WV or less are not indicated except for electrolytics under no-signal (detuned) conditions.
and tantalums. no mark : FM
• All resistors are in Ω and 1 /4 W or less unless otherwise ( ) : AM
specified. • Voltages are taken with a VOM (Input impedance 10 MΩ).
• f : internal component. Voltage variations may be noted due to normal produc-
• U : B+ Line. tion tolerances.
• H : adjustment for repair. • Signal path.
• Power voltage is dc 9V and fed with regulated dc power F : FM
supply from battery terminal. f : AM

– 25 – – 26 –
CFD-S22/S32

6-7. PRINTED WIRING BOARD — CD SECTION — • Refer to page 18 for Circuit Boards Location.
• Waveforms (MODE: PLAY)
1 2 3 4 5 6 7 8 9 10
1
2.2Vp-p
A • Semiconductor
Location 16.9344MHz
Ref. No. Location IC702 yj (XTAO)
IC701 H-7
IC702 E-5 2
IC703 B-5
2Vp-p
B Q701 F-8
Q702 J-7 7.6µsec
IC702 wh (MDP)

3
1.2±0.3Vp-p
C
IC701 qg (RFO)

4
C763
C764 2.5V
D
Approx. 200mVp-p
IC701 qd (FE)
TP
C766 C773
(RF) 5
(Page 33)
2.5V
E
Approx. 100mVp-p
IC701 qa (TE)

Note on Printed Wiring Boards:

• X : parts extracted from the component side.
J • b : Pattern from the side which enables seeing.
04

– 27 – – 28 –
 CFD-S22/S32

6-8. SCHEMATIC DIAGRAM — CD SECTION — • Refer to page 47 for IC Block Diagrams.

(Page 35)

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF • Power voltage is dc 9V and fed with regulated dc power
50 WV or less are not indicated except for electrolytics supply from battery terminal.
and tantalums. • Voltage and waveforms are dc with respect to ground
• All resistors are in Ω and 1/ 4 W or less unless otherwise under no-signal (detuned) conditions.
specified. no mark : CD STOP
∗ : Impossible to measure
Note: Note: • Voltages are taken with a VOM (Input impedance 10 MΩ).
The components identi- Les composants identifiés par Voltage variations may be noted due to normal produc-
fied by mark 0 or dotted une marque 0 sont critiques tion tolerances.
line with mark 0 are criti- pour la sécurité. • Waveforms are taken with a oscilloscope.
cal for safety. Ne les remplacer que par une Voltage variations may be noted due to normal produc-
Replace only with part piéce portant le numéro tion tolerances.
number specified. spécifié. • Circled numbers refer to waveforms.
• Signal path.
• U : B+ Line.
J : CD

– 29 – – 30 –
CFD-S22/S32

6-9. SCHEMATIC DIAGRAM — TC SECTION — • Refer to page 48 for IC Block Diagrams.

• Semiconductor Location
Ref. No. Location Ref. No. Location
D322 G-11 (Q123) G-11
D323 H-11 Q124 G-12
D324 B-10 Q221 E-11
D504 C-8 Q222 E-11
D505 C-8 (Q223) F-11
(D506) E-7 Q224 G-12
(D507) E-7 Q301 B-2
(D508) E-8 Q501 D-8
D509 E-8 Q502 D-8
D510 E-8 Q503 E-8
D511 E-8 Q504 E-8
D953 E-13 Q505 I-8
D956 H-11 Q506 E-8
D957 C-13 Q507 I-8
(Q509) E-7
IC301 C-3 Q510 D-9
IC302 E-10 Q511 D-7
IC304 F-12 Q512 D-7
IC501 H-9 Q513 B-9
IC502 H-10 Q514 C-8
IC503 I-8 Q952 D-13
IC504 G-7 Q953 D-13
Q955 D-12
Q121 E-12 Q957 C-13
Q122 E-11 Q997 B-13
( ) : CFD-S32 only

(Page 35)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified.
• C : panel designation.
• U : B+ Line.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : PB
< > : REC
[ ] : CD STOP
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Signal path.
F : FM
E : PB
a : REC
J : CD
• Abbreviation
CND : Canadian model.
E92 : AC 120V area in E model.
MX : Mexican model.

Note on Printed Wiring Boards:

• X : parts extracted from the component side.
• x : parts mounted on the conductor side.
• b : Pattern from the side which enables seeing.
• Abbreviation
CND : Canadian model.
E92 : AC 120V area in E model.
MX : Mexican model.

– 31 – – 32 –
 CFD-S22/S32
6-10. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 18 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

(Page 23)
A

(Page 28)

(Page 43)
E
L-CH

R-CH
(Page 23)

H LIQUID CRYSTAL DISPLAY PANEL

(Page 40)

04

– 33 – – 34 –
CFD-S22/S32

6-11. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 32 for Note on Schematic Diagram and page 48 for IC Block Diagrams.

(Page 32)

(Page 41)

(Page 37)

(Page 29) (Page 26) (Page 26)

– 35 – – 36 –
 CFD-S22/S32

6-12. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 32 for Note on Schematic Diagram and page 48 for IC Block Diagrams.

(Page 35) (Page 46)

– 37 – – 38 –
CFD-S22/S32

6-13. PRINTED WIRING BOARD — CONTROL SECTION — • Refer to page 18 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11 12 13 14
(Page 33)

OPR/BATT

H
04

• Semiconductor
Location
Ref. No. Location
D601 G-5

Note on Printed Wiring Boards: (IC601) G-10

• X : parts extracted from the component side.
• b : Pattern from the side which enables seeing. ( ) : CFD-S32 only

– 39 – – 40 –
 CFD-S22/S32

6-14. SCHEMATIC DIAGRAM — CONTORL SECTION —

(Page 36)

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified.
• C : panel designation.
• U : B+ Line.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.

– 41 – – 42 –
CFD-S22/S32

6-15. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 18 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11

A • Semiconductor
Location
Ref. No. Location
D901 J-10
DRY BATTERY D902 I-10
SIZE " D " D903 J-9
(IEC DESIGNATION R20)
3PCS, 4.5V
D904 I-9
B

DRY BATTERY
SIZE " D "
(IEC DESIGNATION R20)
3PCS, 4.5V

G
T901
POWER
TRANSFORMER

925
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
(Page 34) • b : Pattern from the side which enables seeing.
J 04
• Abbreviation
CND : Canadian model.

– 43 – – 44 –
 CFD-S22/S32

6-16. SCHEMATIC DIAGRAM — POWER SUPPLY SECTION —

(Page 38)

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• C : panel designation.
Note: Note:
The components identi- Les composants identifiés par
fied by mark 0 or dotted une marque 0 sont critiques
line with mark 0 are criti- pour la sécurité.
cal for safety. Ne les remplacer que par une
Replace only with part piéce portant le numéro
number specified. spécifié.
• U : B+ Line.
• Total current is measured with no cassette installed.
• Power voltage is dc 9V and fed with regulated dc power
supply from battery terminal.
• Abbreviation
CND : Canadian model.

– 45 – – 46 –
• IC Block Diagrams

IC1 TA2149N IC701 CXA2550M IC301 TA2068N

GND1 1 FM RF 24 FM RF-OUT AGC 1 LINE

24 L.LIN

TAPE
AGCVTH 1 VCC L.PO 2
FM RF-IN 2 23 VCC1 20 VCC NAB
1k 23 MIC I/EX
AM 22 AM RF-IN LD 2 AMP1 BUF AMP TAPE
MIX APC PD 56k APC LD L.NF 3 A1 RADIO
AM LOW CUT 3 AMP VCC 22 L.RAD
AMP
FM FM 19 LD ON
MIX OUT 4 21 FM OSC PD 3 REC
MIX OSC AMP1 21 REC
10k L.RO 4
AM
20 AM OSC VEE
OSC 26dB BUF AMP MUTE MONITOR
10k 55k L.IN 5 AMP
BUFF BUFF 56k B1
1/1 OR 10k 20 L.LO

ALC2 ALC1
VCC2 5 19 OSC-OUT VEE
LEVEL 1/16 REF 6 ON 7dB

DET
AM IF DET VREF 1.25V 10k REF
LOGIC 19 VCC
AF IF-IN 6 AMP ON 7dB
ST 18 ST-IND 18 AGCCONT GND 7
FM IF IF BUFF 2.1 BUF AMP 18 R.LO
FM IF-IN 7 1/8 B2
SW VC VCC R.IN 8 REC MUTE MONITOR
13.4k AMP2 AMP
GND2 8 50µA 17 LINE
AM 670mV R.RO 9
DET IF REQ 17 IF-OUT 17 RFTC
AF BUFF VC 26dB RADIO
16 RF I

ON
AGC

MUTE
AGC 9 2k TAPE 16 R.RAD
16 DET-OUT R.NF 10
15k
FM AF NAB
QUAD 10 DET 15 MPX- IN 10k 15 TAPE

TAPE
VC AMP2
PD1 4 R.PO 11
ST/MO 6k 14 R.LIN
R-OUT 11 VC 8k 6p 54k MIC BUF AMP LINE
FM/AM
MUTE VC AMP1 A2
VCO 14 LPF2/MO-ST
L-OUT 12 2k VC VEE 13 MIC
MIC.NF 12
DIVIDE 15 RF O
10k
DECODE 13 LPF1/BAND 2k
PD2 5
14 RFM
VC 8k 6p 2k 24p
32k
174k
32k 87k 13 FE
VEE 6 VEE
24p FOCUS
25k
ERROR
VC 154k AMP
12 FE BIAS IC302 M62429P
260k VC
IC2 LC72137M-TLM F 7
13k 95k
VIN2 VOUT2 VCC CLOCK
VC 12p 30k 8 7 6 5
VC 12p 30k 11 TE
CE 1 E 8 VR 2
DI 2 260k 13k 96k
CCB
CL 3 I/F TRACKING
VCC VOL AMP 2
DO 4 VC ERROR VREF LOGIC
20 XOUT VC
AMP CONTROL
26k VOL AMP 1
EI 9 30k
19 XIN 49 REF AMP
VC 10
30k VR 1
REFERENCE
DIVIDER VC
18 LP-OUT 15k VEE 1 2 3 4
MUTE 5
12BITS PHASE 17 LP-IN VIN1 VOUT1 GND DATA
PROGRAMMABLE DETECTOR
DATA SHIFT REGISTER

MW/LW 6 CHARGE 16 PD
DIVIDER
PUMP
BAND 7 15 VSS
LATCH

UNLOCK
ST-IND 8 DETECTOR
POWER ON 14 VDD
BAND 9 RESET
IC504 BR2401A-W
13 MO/ST

SWALLOW
COUNTER A0 1 1K BIT EEPROM ARRAY
1/2 12 FM IN
1/16,1/17 8 VCC
UNIVERSAL 4BITS 8BIT
7BIT
COUNTER
11 AM IN SLAVE • WORD
ADDRESS ADDRESS DATA 7 WP
DECODER 7BIT REGISTER
A1 2 REGISTER

IF IN 10 START STOP
6 SCL
A2 3 CONTROL CIRCUIT

ACK

GND HIGH VOLTAGE POWER SUPPLY

4
OCCURENCE CIRCUIT VOLTAGE DETECTION 5 SDA

– 47 – – 48 –
 IC702 CXD2587Q

AVDD

AVDD
DOUT

ASYO

RFDC
AVSS

AVSS
RFAC
CLTV

ADIO
IGEN
ASYI
BIAS
FILO
VDD

PCO
VSS

FILI

CE
TE
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

40 SE
DIGITAL ERROR DIGITAL ASYMMETRY

INTERNAL BUS
39 FE
OUT CORRECTOR PLL CORRECTION
38 VC
16K
LRCK 61 RAM OPERATIONAL
D/A EFM AMPLIFIER
PCMD 62
INTERFACE DEMODULATOR ANALOG SWITCH
BCK 63
A/D
CONVERTER
EMPH 64
XVDD 65
CLOCK
37 XTSL
XTAI 66 TIMING GENERATOR
36 TES1
XTAO 67 LOGIC
35 TEST
XVSS 68 SERVO DSP PWM GENERATOR 34 VSS
AVDD1 69
AOUT1 FOCUS FOCUS PWM 33 FRDR
70
SERVO GENERATOR 32 FFDR
AIN1 71 SUBCODE
TRACKING TRACKING 31 TRDR
PROCESSOR
SERVO PWM GENERATOR 30 TFDR
LOUT1 72
PWM PWM SLED SLED PWM 29 SRDR
AVSS1 73 SERVO GENERATOR 28 SFDR
AVSS2 74
3rd ORDER 27 SSTP
LOUT2 75 NOISE SHAPER SERVO
DIGITAL 26 MDP
INTERFACE
CLV 25 LOCK
AIN2 76
OVER SAMPLING
AOUT2 77 DIGITAL FILTER MIRR, DFCT, 24 FOK
AVDD2 78 SERVO AUTO FOK 23 DFCT
RMUT 79 SEQUENCER DETECTOR 22 MIRR
SERIAL IN
LMUT 80 INTERFACE
21 COUT

CPU
INTERFACE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
GFS
SCLK

XLON

SCOR
XLAT

SENS

SPOB

C2PO
XRST
SYSM

WFCK
VDD
SQSO

ATSK

XUGF
SPOA

XPCK
SQCK

CLK
DATA

IC703 BA5974FP
MUTE
FRDR

CAP3
VREF

FFDR
SPIN

GND
VCC

VCC

SP–

SP+
NC

F–

F+

28 27 26 25 24 23 22 21 20 19 18 17 16 15
DRIVE BUFFER

10k 100k 50k POWER

R VCC
PRE VCC F R
+ – MUTE 30k
190k INTERFACE

LEVEL SHIFT
POWER
VCC 50k
THERMAL
SHUTDOWN
30k
F VREF

INTERFACE

F R F
R
DRIVE BUFFER

INTERFACE

F R
R
POWER
VCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VREFOUT

TFDR

TRDR

CAP1

SFDR

SRDR

CAP2

GND

VREFIN

VCC

SL-

SL+

T+

T-

– 49 –
 SECTION 7
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by
number in the exploded views are not supplied. Example : mark 0 or dotted line with mark
• Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ... (RED) 0 are critical for safety.
they are seldom required for routine service. R R Replace only with part number
Some delay should be anticipated Parts Color Cabinet’s Color specified.
when ordering these items. • Accessories and packing materials are
• Abbreviation given in the last of this parts list. Les composants identifiés par une
CND : Canadian model marque 0 sont critiques pour
E92 : AC 120V area in E model la sécurité.
MX : Mexican model Ne les remplacer que par une piéce
portant le numéro spécifié.

7-1. CABINET (FRONT) SECTION

9
#1

SP301 #1 #2

#1
10
7 #1

not supplied
10
5 #2

3
10

#1
10
8
6
4 #1

2
SP302
1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-3378-329-1 CABINET (FRONT) SUB ASSY (SILVER)...(SILVER) 5 3-042-650-01 BUTTON (CD) (SILVER)...(SILVER)
(S22:US) 5 3-042-650-11 BUTTON (CD) (BLACK)...(BLACK) (S22:US)
1 X-3378-334-1 CABINET (FRONT) SUB ASSY (SILVER)...(SILVER) 5 3-042-650-21 BUTTON (CD) (WHITE)...(WHITE) (US)
(S32:US) 6 3-042-649-01 BUTTON (FUNCTION) (SILVER)...(SILVER)
1 X-3378-562-1 CABINET (FRONT) SUB ASSY (SILVER)...(SILVER) 6 3-042-649-11 BUTTON (FUNCTION) (BLACK)...(BLACK)
(S22:CND,E92) (S22:US)
1 X-3378-564-1 CABINET (FRONT) SUB ASSY (SILVER)...(SILVER)
(S32:CND,E92,MX) 6 3-042-649-21 BUTTON (FUNCTION) (WHITE)...(WHITE) (US)
1 X-3378-566-1 CABINET (FRONT) SUB ASSY (BLACK)...(BLACK) * 7 A-3322-447-A CONTROL BOARD, COMPLETE (S22)
(S22:US) * 7 A-3322-470-A CONTROL BOARD, COMPLETE (S32)
8 1-792-206-11 WIRE, PARALLEL (6 CORE) (S22)
1 X-3378-567-1 CABINET (FRONT) SUB ASSY (WHITE)...(WHITE) 8 1-792-207-11 WIRE, PARALLEL (8 CORE) (S32)
(S22:US)
1 X-3378-729-1 CABINET (FRONT) SUB ASSY (WHITE)...(WHITE) 9 3-045-772-01 LID, BATTERY CASE (SILVER)...(SILVER)
(S32:US) 9 3-926-244-61 LID, BATTERY CASE (WHITE)...(WHITE) (US)
2 3-042-646-01 WINDOW (LCD) (S22) 9 3-926-244-91 LID, BATTERY CASE (BLACK)...(BLACK)
2 3-042-646-11 WINDOW (LCD) (S32) (S22:US)
3 3-042-652-01 BUTTON (TEN KEY) 10 4-951-620-11 SCREW (2.6X10), +BVTP
SP301 1-529-215-11 SPEAKER (10cm) (L-CH) (US,CND)
4 3-042-651-01 BUTTON (POWER) (SILVER)...(SILVER) (S22)
4 3-042-651-11 BUTTON (POWER) (SILVER)...(SILVER) (S32) SP301 1-529-340-11 SPEAKER (10cm) (L-CH) (E92,MX)
4 3-042-651-21 BUTTON (POWER) (BLACK)...(BLACK) (S22:US) SP302 1-529-215-11 SPEAKER (10cm) (R-CH) (US,CND)
4 3-042-651-31 BUTTON (POWER) (WHITE)...(WHITE) (S22:US) SP302 1-529-340-11 SPEAKER (10cm) (R-CH) (E92,MX)
4 3-042-651-51 BUTTON (POWER) (WHITE)...(WHITE) (S32:US)

– 50 –
7-2. CABINET (REAR) SECTION

#1 #2
#2

#2

56

57
61
62
#1 60
59
63

T901 57
F902

58
#1
54 65
#1
#1 55
#1 51
64

#1 52
53

The components identified by Les composants identifiés par une

mark 0 or dotted line with mark marque 0 sont critiques pour la
0 are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une piéce
specified. portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 3-041-557-01 CABINET (REAR) (SILVER)...(SILVER) (S22:US) 56 3-036-886-51 HANDLE (SILVER)...(SILVER)
51 3-041-557-11 CABINET (REAR) (SILVER)...(SILVER) (S32:US) 57 4-960-167-01 SCREW (3X8) (DIA.10), +WH
51 3-041-557-41 CABINET (REAR) (SILVER)...(SILVER) * 58 1-676-628-11 HALF BATTERY BOARD
(EXCEPT US) 59 3-028-154-01 TERMINAL (–), BATT
51 3-041-557-61 CABINET (REAR) (BLACK)...(BLACK) (S22:US) 60 3-041-562-01 TERMINAL (REAR), ANTENNA
51 3-041-557-71 CABINET (REAR) (WHITE)...(WHITE) (S22:US)
* 61 1-676-627-11 BATTERY BOARD
51 3-041-557-91 CABINET (REAR) (WHITE)...(WHITE) (S32:US) 62 3-028-154-01 TERMINAL (–), BATT
* 52 A-3322-456-A TUNER BOARD, COMPLETE 63 3-047-439-01 CUSHION
53 3-041-560-01 HOLDER (PWB) (TU) 64 3-363-898-01 CUSHION
* 54 1-676-629-11 SECONDARY BOARD 65 3-034-633-01 COVER (VOL SEL)
* 55 1-676-530-11 POWER BOARD
0 F902 1-576-107-11 FUSE (3.15A) (CND)
56 3-031-540-01 HANDLE (BLACK)...(BLACK) (S22:US) 0 T901 1-433-576-11 TRANSFORMER, POWER
56 3-031-540-21 HANDLE (WHITE)...(WHITE) (US)

– 51 –
7-3. CABINET (UPPER) SECTION
117
ANT1
113
114 115
112
#1 116
S501
118

LCD501 111 119

#1
110
#6 #7

109
108 132 120
107
106 105 122
121
MF-V10-117 131
#1 133
123
not supplied 130 #1
124 125
#1 KSM-213CDM
#1 129 123
#4 125
#3 125
104 134 #3 124
125
#4 103
126
102
135
#1 128
101
#1 127 #5

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 101 A-3322-449-A MAIN BOARD, COMPLETE (S22:US) 115 X-3378-330-1 HOLDER ASSY, CASSETTE (SILVER)...(SILVER)
* 101 A-3322-471-A MAIN BOARD, COMPLETE (S32:US) 115 X-3378-669-1 HOLDER ASSY, CASSETTE (BLACK)...(BLACK)
* 101 A-3322-735-A MAIN BOARD, COMPLETE (S32:E92, MX) (S22:US)
* 101 A-3322-736-A MAIN BOARD, COMPLETE (S32:CND) 115 X-3378-670-1 HOLDER ASSY, CASSETTE (WHITE)...(WHITE)
* 101 A-3322-738-A MAIN BOARD, COMPLETE (S22:E92) (US)
116 3-015-345-01 CUSHION
* 101 A-3322-739-A MAIN BOARD, COMPLETE (S22:CND) 117 3-036-885-61 LID (CD) (SILVER)...(SILVER)
102 1-792-204-11 WIRE, PARALLEL (11 CORE)
* 103 3-041-554-01 LEVER (REC) 117 3-036-885-81 LID (CD) (BLACK)...(BLACK) (S22:US)
* 104 A-3322-448-A TC BOARD, COMPLETE 117 3-036-885-91 LID (CD) (WHITE)...(WHITE) (US)
105 3-045-771-01 BUTTON (PAUSE) (SILVER)...(SILVER) 118 1-452-899-11 MAGNET
119 3-019-395-01 PLATE, CHUCKING
105 3-045-771-11 BUTTON (PAUSE) (BLACK)...(BLACK) (S22:US) 120 3-041-559-01 CABINET (UPPER) (SILVER)...(SILVER)
105 3-045-771-21 BUTTON (PAUSE) (WHITE)...(WHITE) (US)
106 3-045-770-01 BUTTON (STOP) (SILVER)...(SILVER) 120 3-041-559-11 CABINET (UPPER) (BLACK)...(BLACK) (S22:US)
106 3-045-770-11 BUTTON (STOP) (BLACK)...(BLACK) (S22:US) 120 3-041-559-21 CABINET (UPPER) (WHITE)...(WHITE) (US)
106 3-045-770-21 BUTTON (STOP) (WHITE)...(WHITE) (US) 121 3-923-736-01 COVER, CD
* 122 3-041-561-01 TERMINAL (TOP), ANTENNA
107 3-045-769-01 BUTTON (FF) (SILVER)...(SILVER) 123 3-038-948-01 RUBBER, VIBRATION PROOF
107 3-045-769-11 BUTTON (FF) (BLACK)...(BLACK) (S22:US)
107 3-045-769-21 BUTTON (FF) (WHITE)...(WHITE) (US) 124 3-038-948-11 RUBBER, VIBRATION PROOF
108 3-045-768-01 BUTTON (REW) (SILVER)...(SILVER) 125 3-921-725-01 SCREW (2.6X10), +PWH
108 3-045-768-11 BUTTON (REW) (BLACK)...(BLACK) (S22:US) 126 1-792-209-11 WIRE, PARALLEL (16 CORE)
* 127 A-3322-451-A CD BOARD, COMPLETE
108 3-045-768-21 BUTTON (REW) (WHITE)...(WHITE) (US) 128 1-792-208-11 WIRE, PARALLEL (17 CORE)
109 3-045-767-01 BUTTON (PLAY) (SILVER)...(SILVER)
109 3-045-767-11 BUTTON (PLAY) (BLACK)...(BLACK) (S22:US) 129 3-031-561-01 SPRING (CASSETTE)
109 3-045-767-21 BUTTON (PLAY) (WHITE)...(WHITE) (US) 130 4-960-167-01 SCREW (3X8) (DIA.10), +WH
110 3-045-766-01 BUTTON (REC) (SILVER)...(SILVER)3 131 3-031-560-01 SHAFT (MD)
132 3-922-112-41 DAMPER
110 3-045-766-11 BUTTON (REC) (BLACK)...(BLACK) (S22:US) 133 3-031-562-01 SPRING (CD)
110 3-045-766-21 BUTTON (REC) (WHITE)...(WHITE) (US)
111 1-792-205-11 WIRE, PARALLEL (21 CORE) 134 4-951-620-01 SCREW (2.6X8), +BVTP
* 112 3-041-646-01 HOLDER (LCD) 135 3-363-898-01 CUSHION
* 113 1-676-531-11 LCD BOARD ANT1 1-501-883-21 ANTENNA, TELESCOPIC
LCD501 1-803-873-11 DISPLAY PANEL, LIQUID CRYSTAL
114 3-922-112-21 DAMPER S501 1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR
OPEN/CLOSE)

– 52 –
7-4. TAPE MECHANISM SECTION-1
(MF-V10-117)

HRP301 159

HE301
170
160
161
158 157

162

164 167
168
163
165
169

155
156

154

153

166
151

152

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 3-933-010-01 SPRING (S/P), TORSION * 162 3-008-587-01 SLIDER (STOP)
152 3-933-025-01 SPRING (P), TORSION * 163 3-008-591-01 SLIDER (PAUSE)
153 3-040-857-01 LEVER (P) 164 3-933-004-01 CLAW, REEL
154 3-933-024-01 ROLLER, PINCH * 165 3-933-021-01 SLIDER (FRP)
155 3-933-019-01 SPRING (F/R), TORSION * 166 3-933-006-01 SLIDER (EJECT)

156 3-933-028-01 SPRING (FWD), TORSION 167 3-934-833-01 SPRING (FRP)

157 3-933-016-01 GEAR (S REEL) 168 3-022-794-02 SPRING (BT)
158 3-008-590-01 SLIDER (REC) 169 3-933-007-01 PLATE, LOCK
159 3-008-592-01 BASE (H), HEAD * 170 3-012-114-01 LEVER (FR)
* 160 3-008-588-01 SLIDER (REW) HE301 1-543-876-11 HEAD (ERASE)

* 161 3-008-589-13 SLIDER (FF) HRP301 1-500-454-11 HEAD, MAGNETIC (RECORD/PLAYBACK)

– 53 –
7-5. TAPE MECHANISM SECTION-2
(MF-V10-117)

207

206
211

208 212

219
204 205

203

S304

220
213 218

209
M301

210

217

214

215
#8
216
201 202

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 3-933-029-01 LEVER, ERASING PREVENTION 212 X-3372-924-1 FLYWHEEL ASSY
202 3-933-182-01 SPRING, CASSETTE 213 3-932-993-01 CHASSIS, OUTSERT
203 3-932-995-01 GEAR (MID) 214 3-343-358-01 RING, RETAINING
204 X-3371-667-1 CLUTCH ASSY 215 3-933-005-01 SPRING (CAM), COMPRESSION
205 3-932-997-01 GEAR (CAM) 216 3-016-349-01 WASHER

* 206 3-932-999-01 SLIDER (SW) 217 3-937-760-01 SPRING (GROUND), COMPRESSION

207 3-932-998-01 SPRING (GROUND), TORSION 218 3-934-336-01 BEARING
208 3-009-648-01 LEVER (S.OFF) 219 3-939-383-02 SPRING, COMPRESSION
209 3-936-438-01 LEVER (K) 220 3-009-650-02 SPRING (K), COMPRESSION
210 X-3373-572-1 REEL ASSY (N), T M301 A-3320-446-A MOTOR ASSY (CAPSTAN/REEL)

211 3-933-020-01 BELT S304 1-692-302-11 SWITCH, LEAF (TAPE PLAY)

– 54 –
7-6. OPTICAL PICK-UP SECTION
(KSM-213CDM)

255

not supplied
251

256

252

253
254

M701

M702

The components identified by Les composants identifiés par une

mark 0 or dotted line with mark marque 0 sont critiques pour la
0 are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une piéce
specified. portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
0 251 8-848-483-05 PICK-UP, OPTICAL KSS-213C/Q-RP 255 2-626-907-01 GEAR (A)
252 3-713-786-51 SCREW +P 2X3 256 2-627-003-02 GEAR (B) (RP)
253 2-626-908-01 SHAFT, SLED M702 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED)
254 X-2626-202-1 CHASSIS ASSY (MB), MOTOR (SPINDLE)
(INCLUDING M701)

– 55 –
 SECTION 8
BATTERY CD ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark 0 or dotted line with mark
parts specified in the diagrams or the Some delay should be anticipated 0 are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. Les composants identifiés par une
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. marque 0 sont critiques pour
All resistors are in ohms. • CAPACITORS la sécurité.
METAL:Metal-film resistor. uF : µF Ne les remplacer que par une piéce
METAL OXIDE: Metal oxide-film resistor. • COILS portant le numéro spécifié.
F:nonflammable uH : µH
• Abbreviation When indicating parts by reference
CND : Canadian model number, please include the board.
E92 : AC 120V area in E model
MX : Mexican model

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-676-627-11 BATTERY BOARD C740 1-163-255-11 CERAMIC CHIP 150PF 5% 50V
************** C743 1-163-255-11 CERAMIC CHIP 150PF 5% 50V
C744 1-163-007-11 CERAMIC CHIP 680PF 10% 50V
3-028-154-01 TERMINAL (–), BATT C745 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
************************************************************* C746 1-126-925-11 ELECT 470uF 20% 10V

* A-3322-451-A CD BOARD, COMPLETE C747 1-163-059-11 CERAMIC CHIP 0.01uF 10% 50V
******************* C757 1-163-181-00 CERAMIC CHIP 100PF 5% 50V
C758 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
< CAPACITOR > C759 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C760 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C701 1-104-665-11 ELECT 100uF 20% 10V
C702 1-115-185-11 CERAMIC CHIP 0.033uF 10% 50V C761 1-104-665-11 ELECT 100uF 20% 10V
C703 1-163-113-00 CERAMIC CHIP 68PF 5% 50V C762 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C704 1-104-664-11 ELECT 47uF 20% 10V C763 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C706 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C764 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C765 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
C707 1-104-665-11 ELECT 100uF 20% 10V
C708 1-104-665-11 ELECT 100uF 20% 10V C766 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C709 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C768 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C710 1-104-665-11 ELECT 100uF 20% 10V C770 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C711 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C773 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C780 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C712 1-163-019-00 CERAMIC CHIP 6800PF 10% 50V
C713 1-164-343-11 CERAMIC CHIP 0.056uF 10% 25V C781 1-104-665-11 ELECT 100uF 20% 10V
C714 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V
C715 1-163-189-00 CERAMIC CHIP 220PF 10% 50V < CONNECTOR >
C716 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
CNP701 1-779-466-11 CONNECTOR, FFC (LIF(NON-ZIF)) 16P
C717 1-104-665-11 ELECT 100uF 20% 10V CNP702 1-784-739-11 CONNECTOR, FFC 17P
C718 1-163-059-11 CERAMIC CHIP 0.01uF 10% 50V
C720 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V < IC >
C721 1-163-059-11 CERAMIC CHIP 0.01uF 10% 50V
C722 1-126-959-11 ELECT 0.47uF 20% 50V IC701 8-752-083-15 IC CXA2550M
IC702 8-752-386-85 IC CXD2587Q
C723 1-163-189-00 CERAMIC CHIP 220PF 5% 50V IC703 8-759-549-28 IC BA5974FP-E2
C726 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
C727 1-104-760-11 CERAMIC CHIP 0.047uF 10% 50V < JUMPER RESISTOR >
C728 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C729 1-104-665-11 ELECT 100uF 20% 10V JC701 1-216-296-00 SHORT 0
JC702 1-216-296-00 SHORT 0
C730 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC703 1-216-296-00 SHORT 0
C731 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC704 1-216-296-00 SHORT 0
C732 1-163-059-11 CERAMIC CHIP 0.01uF 10% 50V JC705 1-216-296-00 SHORT 0
C733 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C734 1-163-235-11 CERAMIC CHIP 22PF 5% 50V JC706 1-216-296-00 SHORT 0
JC707 1-216-296-00 SHORT 0
C735 1-126-963-11 ELECT 4.7uF 20% 50V JC708 1-216-296-00 SHORT 0
C736 1-126-963-11 ELECT 4.7uF 20% 50V JC709 1-216-296-00 SHORT 0
C737 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC710 1-216-296-00 SHORT 0
C738 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C739 1-163-007-11 CERAMIC CHIP 680PF 10% 50V JC711 1-216-296-00 SHORT 0
JC712 1-216-296-00 SHORT 0

– 56 –
 CD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
JC713 1-216-295-00 SHORT 0 JC768 1-216-296-00 SHORT 0
JC714 1-216-296-00 SHORT 0 JC769 1-216-296-00 SHORT 0
JC715 1-216-296-00 SHORT 0 JC770 1-216-296-00 SHORT 0
JC716 1-216-296-00 SHORT 0 JC771 1-216-296-00 SHORT 0
JC717 1-216-296-00 SHORT 0 JC772 1-216-295-00 SHORT 0

JC718 1-216-296-00 SHORT 0 JC773 1-216-296-00 SHORT 0

JC719 1-216-296-00 SHORT 0 JC774 1-216-296-00 SHORT 0
JC720 1-216-296-00 SHORT 0 JC775 1-216-295-00 SHORT 0
JC721 1-216-296-00 SHORT 0 JC776 1-216-295-00 SHORT 0
JC722 1-216-296-00 SHORT 0 JC777 1-216-295-00 SHORT 0

JC723 1-216-296-00 SHORT 0 JC778 1-216-295-00 SHORT 0

JC724 1-216-296-00 SHORT 0
JC725 1-216-296-00 SHORT 0 < COIL >
JC726 1-216-296-00 SHORT 0
JC727 1-216-296-00 SHORT 0 L701 1-216-296-00 SHORT 0
L702 1-216-296-00 SHORT 0
JC728 1-216-296-00 SHORT 0 L703 1-216-295-00 SHORT 0
JC729 1-216-296-00 SHORT 0 L704 1-216-295-00 SHORT 0
JC730 1-216-296-00 SHORT 0 L705 1-216-296-00 SHORT 0
JC731 1-216-296-00 SHORT 0
JC732 1-216-296-00 SHORT 0 L706 1-216-296-00 SHORT 0
L707 1-216-296-00 SHORT 0
JC733 1-216-296-00 SHORT 0 L708 1-216-296-00 SHORT 0
JC734 1-216-296-00 SHORT 0 L709 1-216-296-00 SHORT 0
JC735 1-216-296-00 SHORT 0 L710 1-216-296-00 SHORT 0
JC736 1-216-296-00 SHORT 0
JC737 1-216-296-00 SHORT 0 L711 1-216-296-00 SHORT 0

JC738 1-216-296-00 SHORT 0 < TRANSISTOR >

JC739 1-216-296-00 SHORT 0
JC740 1-216-296-00 SHORT 0 Q701 8-729-903-46 TRANSISTOR 2SB1132-P
JC741 1-216-295-00 SHORT 0 Q702 8-729-900-53 TRANSISTOR DTC114EK
JC742 1-216-296-00 SHORT 0
< RESISTOR >
JC743 1-216-296-00 SHORT 0
JC744 1-216-296-00 SHORT 0 R701 1-216-254-00 RES-CHIP 220K 5% 1/8W
JC745 1-216-296-00 SHORT 0 R702 1-216-254-00 RES-CHIP 220K 5% 1/8W
JC746 1-216-296-00 SHORT 0 R703 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
JC747 1-216-296-00 SHORT 0 R704 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R705 1-216-089-11 RES-CHIP 47K 5% 1/10W
JC748 1-216-296-00 SHORT 0
JC750 1-216-295-00 SHORT 0 R708 1-216-001-00 METAL CHIP 10 5% 1/10W
JC751 1-216-296-00 SHORT 0 R709 1-216-234-00 RES-CHIP 33K 5% 1/8W
JC752 1-216-296-00 SHORT 0 R712 1-216-222-00 RES-CHIP 10K 5% 1/8W
JC754 1-216-295-00 SHORT 0 R713 1-216-085-00 METAL CHIP 33K 5% 1/10W
R714 1-216-099-00 METAL CHIP 120K 5% 1/10W
JC755 1-216-296-00 SHORT 0
JC756 1-216-296-00 SHORT 0 R715 1-216-085-00 METAL CHIP 33K 5% 1/10W
JC757 1-216-296-00 SHORT 0 R716 1-216-085-00 METAL CHIP 33K 5% 1/10W
JC758 1-216-296-00 SHORT 0 R717 1-216-073-00 METAL CHIP 10K 5% 1/10W
JC759 1-216-296-00 SHORT 0 R718 1-216-097-11 RES-CHIP 100K 5% 1/10W
R719 1-216-270-00 RES-CHIP 1M 5% 1/8W
JC760 1-216-296-00 SHORT 0
JC761 1-216-296-00 SHORT 0 R720 1-216-073-00 METAL CHIP 10K 5% 1/10W
JC762 1-216-296-00 SHORT 0 R721 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
JC763 1-216-296-00 SHORT 0 R722 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
JC764 1-216-295-00 SHORT 0 R723 1-216-075-00 METAL CHIP 12K 5% 1/10W
R724 1-216-075-00 METAL CHIP 12K 5% 1/10W
JC765 1-216-295-00 SHORT 0
JC766 1-216-296-00 SHORT 0 R725 1-216-075-00 METAL CHIP 12K 5% 1/10W
JC767 1-216-296-00 SHORT 0 R726 1-216-075-00 METAL CHIP 12K 5% 1/10W

– 57 –
 CD CONTROL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R727 1-216-075-00 METAL CHIP 12K 5% 1/10W < RESISTOR >
R728 1-216-075-00 METAL CHIP 12K 5% 1/10W
R730 1-216-065-11 RES-CHIP 4.7K 5% 1/10W R601 1-249-415-11 CARBON 680 5% 1/4W
R731 1-216-238-11 RES-CHIP 47K 5% 1/8W R602 1-249-416-11 CARBON 820 5% 1/4W
R741 1-216-037-00 METAL CHIP 330 5% 1/10W R603 1-249-418-11 CARBON 1.2K 5% 1/4W
R604 1-249-420-11 CARBON 1.8K 5% 1/4W
R759 1-216-097-11 RES-CHIP 100K 5% 1/10W R605 1-249-429-11 CARBON 10K 5% 1/4W
R760 1-216-246-00 RES-CHIP 100K 5% 1/8W
R761 1-216-097-11 RES-CHIP 100K 5% 1/10W R606 1-249-432-11 CARBON 18K 5% 1/4W
R762 1-216-246-00 RES-CHIP 100K 5% 1/8W R607 1-249-415-11 CARBON 680 5% 1/4W
R774 1-216-055-00 RES-CHIP 1.8K 5% 1/10W R608 1-249-416-11 CARBON 820 5% 1/4W
R609 1-249-418-11 CARBON 1.2K 5% 1/4W
R775 1-216-049-11 RES-CHIP 1K 5% 1/10W R610 1-249-420-11 CARBON 1.8K 5% 1/4W
R776 1-216-065-11 RES-CHIP 4.7K 5% 1/10W
R777 1-216-055-00 RES-CHIP 1.8K 5% 1/10W R611 1-247-843-11 CARBON 3.3K 5% 1/4W
R779 1-216-049-11 RES-CHIP 1K 5% 1/10W R612 1-249-427-11 CARBON 6.8K 5% 1/4W
R780 1-216-065-11 RES-CHIP 4.7K 5% 1/10W R613 1-249-432-11 CARBON 18K 5% 1/4W
R616 1-249-415-11 CARBON 680 5% 1/4W
R781 1-216-049-11 RES-CHIP 1K 5% 1/10W R617 1-249-424-11 CARBON 3.9K 5% 1/4W
R782 1-216-055-00 RES-CHIP 1.8K 5% 1/10W
R783 1-216-089-11 RES-CHIP 47K 5% 1/10W R618 1-247-843-11 CARBON 3.3K 5% 1/4W
R785 1-216-222-00 RES-CHIP 10K 5% 1/8W R619 1-249-427-11 CARBON 6.8K 5% 1/4W
R786 1-216-065-11 RES-CHIP 4.7K 5% 1/10W R620 1-249-432-11 CARBON 18K 5% 1/4W
R621 1-249-415-11 CARBON 680 5% 1/4W
R787 1-216-206-00 RES-CHIP 2.2K 5% 1/8W R622 1-249-416-11 CARBON 820 5% 1/4W
R788 1-216-049-11 RES-CHIP 1K 5% 1/10W
R790 1-216-049-11 RES-CHIP 1K 5% 1/10W R623 1-249-418-11 CARBON 1.2K 5% 1/4W
R791 1-216-246-00 RES-CHIP 100K 5% 1/8W R624 1-249-420-11 CARBON 1.8K 5% 1/4W
R799 1-216-089-11 RES-CHIP 47K 5% 1/10W R625 1-247-843-11 CARBON 3.3K 5% 1/4W
R626 1-249-427-11 CARBON 6.8K 5% 1/4W
< SWITCH > R627 1-249-432-11 CARBON 18K 5% 1/4W

S702 1-762-812-11 SWITCH, LEAF (LIMIT) R628 1-247-815-11 CARBON 220 5% 1/4W
R629 1-247-826-00 CARBON 620 5% 1/4W
< VIBRATOR > R630 1-249-437-11 CARBON 47K 5% 1/4W
(S32)
X701 1-577-253-11 VIBRATOR, CERAMIC (16.9344MHz)
************************************************************* < SWITCH >

* A-3322-447-A CONTROL BOARD, COMPLETE (S22) S601 1-762-798-11 SWITCH, KEY BOARD (POWER)
* A-3322-470-A CONTROL BOARD, COMPLETE (S32) S602 1-762-798-11 SWITCH, KEY BOARD (SLEEP)
************************* S603 1-762-798-11 SWITCH, KEY BOARD (+ VOLUME)
S604 1-762-798-11 SWITCH, KEY BOARD (– VOLUME)
< CAPACITOR > S605 1-762-798-11 SWITCH, KEY BOARD (MEGA BASS) (S32)

C602 1-161-494-00 CERAMIC 0.022uF 25V S606 1-762-798-11 SWITCH, KEY BOARD (MEGA BASS) (S22)
(S32) S607 1-762-798-11 SWITCH, KEY BOARD (N X)
S608 1-762-798-11 SWITCH, KEY BOARD (x)
< CONNECTOR > S609 1-762-798-11 SWITCH, KEY BOARD (> + TUNING)
S610 1-762-798-11 SWITCH, KEY BOARD (– . TUNING)
* CNP601 1-770-516-31 CONNECTOR, FFC/FPC 8P (S32)
CNP601 1-770-540-31 CONNECTOR, FFC/FPC 6P (S22) S611 1-762-798-11 SWITCH, KEY BOARD (PLAY MODE MONO/ST)
S612 1-762-798-11 SWITCH, KEY BOARD (DISPLAY ENT MEMORY)
< DIODE > S613 1-762-798-11 SWITCH, KEY BOARD (CD)
S614 1-762-798-11 SWITCH, KEY BOARD (RADIO BAND AUTO
D601 8-719-059-97 LED L-34HD (OPR/BATT) PRESET)
S615 1-762-798-11 SWITCH, KEY BOARD (TAPE)
< IC >
S616 1-762-798-11 SWITCH, KEY BOARD (9)
IC601 8-749-014-88 IC SPS-440-E (S32) S617 1-762-798-11 SWITCH, KEY BOARD (0/10)
S618 1-762-798-11 SWITCH, KEY BOARD (>10)
S619 1-762-798-11 SWITCH, KEY BOARD (1)
S620 1-762-798-11 SWITCH, KEY BOARD (2)

– 58 –
 CONTROL HALF BATTERY LCD MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
S621 1-762-798-11 SWITCH, KEY BOARD (3) C131 1-126-926-11 ELECT 1000uF 20% 10V
S622 1-762-798-11 SWITCH, KEY BOARD (4) C132 1-136-165-00 MYLAR 0.1uF 5% 50V
S623 1-762-798-11 SWITCH, KEY BOARD (5) C221 1-126-956-11 ELECT 0.1uF 20% 50V
S624 1-762-798-11 SWITCH, KEY BOARD (6) C222 1-162-294-31 CERAMIC 0.001uF 10% 50V
S625 1-762-798-11 SWITCH, KEY BOARD (7) C223 1-126-961-11 ELECT 2.2uF 20% 50V

S626 1-762-798-11 SWITCH, KEY BOARD (8) C224 1-127-876-21 CERAMIC 0.01uF 10% 50V
S627 1-762-798-11 SWITCH, KEY BOARD (TONE) (S32) (EXCEPT E92, MX)
************************************************************* C224 1-127-880-21 CERAMIC 0.022uF 10% 50V
(E92, MX)
* 1-676-628-11 HALF BATTERY BOARD C225 1-162-302-11 CERAMIC 0.0022uF 30% 16V
******************* C226 1-126-960-11 ELECT 1uF 20% 50V
C227 1-127-888-21 CERAMIC 0.1uF 10% 50V
3-028-154-01 TERMINAL (–), BATT (S32)

< CONNECTOR > C228 1-162-294-31 CERAMIC 0.001uF 10% 50V

C229 1-104-664-11 ELECT 47uF 20% 10V
* CNP904 1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P C230 1-104-665-11 ELECT 100uF 20% 10V
************************************************************* C231 1-126-926-11 ELECT 1000uF 20% 10V
C232 1-136-165-00 MYLAR 0.1uF 5% 50V
* 1-676-531-11 LCD BOARD
********** C321 1-126-934-11 ELECT 220uF 20% 10V
C322 1-104-664-11 ELECT 47uF 20% 10V
* 3-041-646-01 HOLDER (LCD) C323 1-126-964-11 ELECT 10uF 20% 50V
C324 1-162-306-11 CERAMIC 0.01uF 20% 16V
< CONNECTOR > C325 1-126-937-11 ELECT 4700uF 20% 16V

CNP651 1-568-864-11 CONNECTOR, FFC 21P C326 1-126-934-11 ELECT 220uF 20% 16V
C327 1-162-282-31 CERAMIC 100PF 10% 50V
< LIQUID CRYSTAL DISPLAY > C328 1-162-282-31 CERAMIC 100PF 10% 50V
C329 1-162-306-11 CERAMIC 0.01uF 20% 16V
LCD501 1-803-873-11 DISPLAY PANEL, LIQUID CRYSTAL C331 1-104-664-11 ELECT 47uF 20% 10V
*************************************************************
C335 1-104-664-11 ELECT 47uF 20% 10V
* A-3322-449-A MAIN BOARD, COMPLETE (S22:US) (S32)
* A-3322-471-A MAIN BOARD, COMPLETE (S32:US) C501 1-126-933-11 ELECT 100uF 20% 16V
* A-3322-735-A MAIN BOARD, COMPLETE (S32:E92, MX) C502 1-162-306-11 CERAMIC 0.01uF 20% 16V
* A-3322-736-A MAIN BOARD, COMPLETE (S32:CND) C503 1-104-665-11 ELECT 100uF 20% 10V
* A-3322-738-A MAIN BOARD, COMPLETE (S22:E92) C504 1-104-665-11 ELECT 100uF 20% 10V

* A-3322-739-A MAIN BOARD, COMPLETE (S22:CND) C505 1-162-306-11 CERAMIC 0.01uF 20% 16V
********************* C506 1-162-201-31 CERAMIC 12PF 5% 50V
C507 1-162-201-31 CERAMIC 12PF 5% 50V
7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S C508 1-126-960-11 ELECT 1uF 20% 50V
C513 1-128-802-21 CERAMIC 27PF 5% 50V
< CAPACITOR >
C514 1-128-802-21 CERAMIC 27PF 5% 50V
C121 1-126-956-11 ELECT 0.1uF 20% 50V C518 1-126-964-11 ELECT 10uF 20% 50V
C122 1-162-294-31 CERAMIC 0.001uF 10% 50V C519 1-126-964-11 ELECT 10uF 20% 50V
C123 1-126-961-11 ELECT 2.2uF 20% 50V (S32)
C124 1-127-876-21 CERAMIC 0.01uF 10% 50V C520 1-104-664-11 ELECT 47uF 20% 10V
(EXCEPT E92, MX) (S32)
C124 1-127-880-21 CERAMIC 0.022uF 10% 50V C522 1-104-665-11 ELECT 100uF 20% 10V
(E92, MX)
C531 1-162-282-31 CERAMIC 100PF 10% 50V
C125 1-162-302-11 CERAMIC 0.0022uF 30% 16V C532 1-162-286-21 CERAMIC 220PF 10% 50V
C126 1-126-960-11 ELECT 1uF 20% 50V C533 1-162-282-31 CERAMIC 100PF 10% 50V
C127 1-127-888-21 CERAMIC 0.1uF 10% 50V C534 1-162-294-31 CERAMIC 0.001uF 10% 50V
(S32) C535 1-162-282-31 CERAMIC 100PF 10% 50V
C128 1-162-294-31 CERAMIC 0.001uF 10% 50V
C129 1-104-664-11 ELECT 47uF 20% 10V C536 1-162-282-31 CERAMIC 100PF 10% 50V
C537 1-162-282-31 CERAMIC 100PF 10% 50V
C130 1-104-665-11 ELECT 100uF 20% 10V C538 1-162-306-11 CERAMIC 0.01uF 20% 16V

– 59 –
 MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C540 1-162-306-11 CERAMIC 0.01uF 20% 16V < CABLE HOLDER >
C541 1-126-960-11 ELECT 1uF 20% 50V
C542 1-162-306-11 CERAMIC 0.01uF 20% 16V * KH321 1-565-385-11 HOLDER, CABLE 4P
C543 1-162-282-31 CERAMIC 100PF 10% 50V * KH503 1-565-386-11 HOLDER, CABLE 5P
C544 1-162-282-31 CERAMIC 100PF 10% 50V
< TRANSISTOR >
C545 1-162-294-31 CERAMIC 0.001uF 10% 50V
C547 1-162-306-11 CERAMIC 0.01uF 20% 16V Q121 8-729-194-57 TRANSISTOR 2SC945-P
C951 1-162-306-11 CERAMIC 0.01uF 20% 16V Q122 8-729-194-57 TRANSISTOR 2SC945-P
C952 1-162-306-11 CERAMIC 0.01uF 20% 16V Q123 8-729-036-80 TRANSISTOR KRC110M (S32)
C953 1-126-934-11 ELECT 220uF 20% 10V Q124 8-729-036-89 TRANSISTOR KTC3198GR-AT
Q221 8-729-194-57 TRANSISTOR 2SC945-P
C957 1-162-306-11 CERAMIC 0.01uF 20% 16V
C959 1-104-665-11 ELECT 100uF 20% 10V Q222 8-729-194-57 TRANSISTOR 2SC945-P
C999 1-127-880-21 CERAMIC 0.022uF 10% 50V Q223 8-729-036-80 TRANSISTOR KRC110M (S32)
Q224 8-729-036-89 TRANSISTOR KTC3198GR-AT
< CONNECTOR > Q501 8-729-037-34 TRANSISTOR KRA107M
Q502 8-729-036-58 TRANSISTOR KRC102M-AT
CNP322 1-506-986-11 PIN, CONNECTOR (PC BOARD) 4P
CNP323 1-506-986-11 PIN, CONNECTOR (PC BOARD) 4P Q503 8-729-037-34 TRANSISTOR KRA107M
CNP501 1-691-040-31 CONNECTOR, FFC 8P (S32) Q504 8-729-036-77 TRANSISTOR KRC107M
CNP501 1-784-767-11 CONNECTOR, FFC 6P (S22) Q505 8-729-036-77 TRANSISTOR KRC107M
CNP502 1-784-739-11 CONNECTOR, FFC 17P Q506 8-729-036-77 TRANSISTOR KRC107M
Q507 8-729-036-77 TRANSISTOR KRC107M
CNP505 1-568-830-11 CONNECTOR, FFC 11P
CNP551 1-784-782-11 CONNECTOR, FFC 21P Q509 8-729-036-89 TRANSISTOR KTC3198GR-AT (S32)
Q510 8-729-036-77 TRANSISTOR KRC107M
< DIODE > Q511 8-729-036-77 TRANSISTOR KRC107M
Q512 8-729-037-13 TRANSISTOR KTA1271Y
D322 8-719-991-33 DIODE 1SS133T-77 Q513 8-729-037-13 TRANSISTOR KTA1271Y
D323 8-719-991-33 DIODE 1SS133T-77
D324 8-719-991-33 DIODE 1SS133T-77 Q514 8-729-036-77 TRANSISTOR KRC107M
D504 8-719-991-33 DIODE 1SS133T-77 Q951 8-729-036-57 TRANSISTOR KRC101M-AT (EXCEPT US)
D505 8-719-991-33 DIODE 1SS133T-77 Q952 8-729-037-13 TRANSISTOR KTA1271Y
Q953 8-729-036-57 TRANSISTOR KRC101M-AT
D506 8-719-109-89 DIODE RD5.6ESB2 (S32) Q955 8-729-021-82 TRANSISTOR 2SD2396K
D507 8-719-991-33 DIODE 1SS133T-77 (S32)
D508 8-719-991-33 DIODE 1SS133T-77 (S32) Q957 8-729-036-86 TRANSISTOR KTC3203Y-AT
D509 8-719-991-33 DIODE 1SS133T-77 Q997 8-729-036-57 TRANSISTOR KRC101M-AT
D510 8-719-991-33 DIODE 1SS133T-77
< RESISTOR >
D511 8-719-991-33 DIODE 1SS133T-77
D951 8-719-991-33 DIODE 1SS133T-77 (EXCEPT US) R121 1-249-419-11 CARBON 1.5K 5% 1/4W
D952 8-719-991-33 DIODE 1SS133T-77 (EXCEPT US) R122 1-249-422-11 CARBON 2.7K 5% 1/4W
D953 8-719-109-97 DIODE RD6.8ES-B2 R123 1-247-895-11 CARBON 470K 5% 1/4W
D955 8-719-991-33 DIODE 1SS133T-77 (EXCEPT US) R125 1-247-843-11 CARBON 3.3K 5% 1/4W
R126 1-249-417-11 CARBON 1K 5% 1/4W
D956 8-719-991-33 DIODE 1SS133T-77 (E92, MX)
D957 8-719-109-72 DIODE RD3.9ES-B2
R126 1-249-421-11 CARBON 2.2K 5% 1/4W
< IC > (EXCEPT E92, MX)
R127 1-249-429-11 CARBON 10K 5% 1/4W
IC302 8-759-539-45 IC M62429P R128 1-249-415-11 CARBON 680 5% 1/4W
IC304 8-759-426-51 IC BA5417 R130 1-247-815-11 CARBON 220 5% 1/4W
IC501 8-752-915-52 IC CXP83620-022Q R131 1-249-437-11 CARBON 47K 5% 1/4W
IC502 8-759-658-46 IC S81233SGY-Z
IC503 8-759-645-87 IC PST9128-T R132 1-247-807-31 CARBON 100 5% 1/4W
R140 1-249-421-11 CARBON 2.2K 5% 1/4W
IC504 8-759-641-21 IC BR24C01A-W R221 1-249-419-11 CARBON 1.5K 5% 1/4W
R222 1-249-422-11 CARBON 2.7K 5% 1/4W
< JACK > R223 1-247-895-11 CARBON 470K 5% 1/4W

J321 1-779-050-11 JACK (i) R225 1-247-843-11 CARBON 3.3K 5% 1/4W

– 60 –
 MAIN POWER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R226 1-249-417-11 CARBON 1K 5% 1/4W R541 1-249-417-11 CARBON 1K 5% 1/4W
(E92, MX) R562 1-249-425-11 CARBON 4.7K 5% 1/4W
R226 1-249-421-11 CARBON 2.2K 5% 1/4W R563 1-249-429-11 CARBON 10K 5% 1/4W
(EXCEPT E92, MX) (S32)
R227 1-249-429-11 CARBON 10K 5% 1/4W R565 1-249-417-11 CARBON 1K 5% 1/4W
R228 1-249-415-11 CARBON 680 5% 1/4W R566 1-249-417-11 CARBON 1K 5% 1/4W
R230 1-247-815-11 CARBON 220 5% 1/4W
R569 1-249-417-11 CARBON 1K 5% 1/4W
R231 1-249-437-11 CARBON 47K 5% 1/4W R570 1-249-417-11 CARBON 1K 5% 1/4W
R232 1-247-807-31 CARBON 100 5% 1/4W R571 1-249-417-11 CARBON 1K 5% 1/4W
R240 1-249-421-11 CARBON 2.2K 5% 1/4W R576 1-247-843-11 CARBON 3.3K 5% 1/4W
R321 1-249-408-11 CARBON 180 5% 1/4W R577 1-249-417-11 CARBON 1K 5% 1/4W
R322 1-249-417-11 CARBON 1K 5% 1/4W
R578 1-249-429-11 CARBON 10K 5% 1/4W
R323 1-247-903-00 CARBON 1M 5% 1/4W R579 1-249-417-11 CARBON 1K 5% 1/4W
R324 1-249-441-11 CARBON 100K 5% 1/4W R580 1-249-417-11 CARBON 1K 5% 1/4W
R327 1-249-413-11 CARBON 470 5% 1/4W R581 1-249-425-11 CARBON 4.7K 5% 1/4W
R501 1-249-417-11 CARBON 1K 5% 1/4W R582 1-249-429-11 CARBON 10K 5% 1/4W
R502 1-249-417-11 CARBON 1K 5% 1/4W
(S32) R583 1-249-425-11 CARBON 4.7K 5% 1/4W
R584 1-249-425-11 CARBON 4.7K 5% 1/4W
R503 1-249-417-11 CARBON 1K 5% 1/4W R585 1-249-425-11 CARBON 4.7K 5% 1/4W
R504 1-249-441-11 CARBON 100K 5% 1/4W R586 1-249-425-11 CARBON 4.7K 5% 1/4W
R505 1-249-417-11 CARBON 1K 5% 1/4W R587 1-249-437-11 CARBON 47K 5% 1/4W
R506 1-249-417-11 CARBON 1K 5% 1/4W
R507 1-249-417-11 CARBON 1K 5% 1/4W R588 1-249-417-11 CARBON 1K 5% 1/4W
R589 1-249-441-11 CARBON 100K 5% 1/4W
R508 1-249-417-11 CARBON 1K 5% 1/4W R590 1-247-843-11 CARBON 3.3K 5% 1/4W
R509 1-249-417-11 CARBON 1K 5% 1/4W R591 1-247-832-11 CARBON 1.1K 5% 1/4W
R510 1-249-417-11 CARBON 1K 5% 1/4W R592 1-249-421-11 CARBON 2.2K 5% 1/4W
R511 1-249-417-11 CARBON 1K 5% 1/4W
R512 1-249-417-11 CARBON 1K 5% 1/4W R593 1-247-895-11 CARBON 470K 5% 1/4W
R595 1-249-417-11 CARBON 1K 5% 1/4W
R513 1-249-417-11 CARBON 1K 5% 1/4W (S32)
R514 1-249-417-11 CARBON 1K 5% 1/4W R596 1-247-807-31 CARBON 100 5% 1/4W
R515 1-249-417-11 CARBON 1K 5% 1/4W (S32)
R516 1-249-417-11 CARBON 1K 5% 1/4W R597 1-249-417-11 CARBON 1K 5% 1/4W
R517 1-249-417-11 CARBON 1K 5% 1/4W R598 1-249-437-11 CARBON 47K 5% 1/4W

R518 1-249-417-11 CARBON 1K 5% 1/4W R599 1-249-425-11 CARBON 4.7K 5% 1/4W

R519 1-249-417-11 CARBON 1K 5% 1/4W R951 1-249-437-11 CARBON 47K 5% 1/4W
R520 1-249-417-11 CARBON 1K 5% 1/4W R952 1-249-417-11 CARBON 1K 5% 1/4W
R521 1-249-417-11 CARBON 1K 5% 1/4W R954 1-247-815-11 CARBON 220 5% 1/4W
R522 1-249-417-11 CARBON 1K 5% 1/4W R955 1-247-807-31 CARBON 100 5% 1/4W

R523 1-249-429-11 CARBON 10K 5% 1/4W R956 1-249-393-11 CARBON 10 5% 1/4W

R524 1-249-417-11 CARBON 1K 5% 1/4W R958 1-249-411-11 CARBON 330 5% 1/4W
R525 1-249-417-11 CARBON 1K 5% 1/4W R960 1-249-393-11 CARBON 10 5% 1/4W
R526 1-249-417-11 CARBON 1K 5% 1/4W R961 1-249-417-11 CARBON 1K 5% 1/4W
R527 1-249-417-11 CARBON 1K 5% 1/4W R997 1-249-429-11 CARBON 10K 5% 1/4W

R528 1-249-417-11 CARBON 1K 5% 1/4W < VIBRATOR >

R529 1-249-417-11 CARBON 1K 5% 1/4W
R530 1-249-429-11 CARBON 10K 5% 1/4W X501 1-781-775-11 VIBRATOR, CERAMIC (4.19MHz)
R534 1-247-843-11 CARBON 3.3K 5% 1/4W X502 1-781-721-11 VIBRATOR, CRYSTAL (150kHz)
R535 1-249-429-11 CARBON 10K 5% 1/4W *************************************************************

R536 1-249-429-11 CARBON 10K 5% 1/4W * 1-676-530-11 POWER BOARD

R537 1-249-429-11 CARBON 10K 5% 1/4W *************
R538 1-249-421-11 CARBON 2.2K 5% 1/4W
R539 1-249-421-11 CARBON 2.2K 5% 1/4W < CAPACITOR >
R540 1-249-417-11 CARBON 1K 5% 1/4W
C908 1-126-964-11 ELECT 10uF 20% 50V

– 61 –
 POWER SECONDARY TC TUNER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< AC INLET > < IC >

0 CNJ901 1-526-818-11 INLET, AC (- AC IN) (EXCEPT US, CND) IC301 8-759-264-71 IC TA2068N
0 CNJ901 1-540-009-11 INLET, AC (- AC IN) (US, CND)
< TRANSISTOR >
< CONNECTOR >
Q301 8-729-281-53 TRANSISTOR 2SC1815-GR
* CNP901 1-580-155-11 PIN, CONNECTOR (PC BOARD) 3P
* CNP902 1-580-165-21 PIN, CONNECTOR (PC BOARD) 4P < RESISTOR >
*************************************************************
R101 1-216-077-11 RES-CHIP 15K 5% 1/10W
* 1-676-629-11 SECONDARY BOARD R102 1-216-023-00 METAL CHIP 82 5% 1/10W
***************** R103 1-216-097-11 RES-CHIP 100K 5% 1/10W
R104 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
1-533-233-31 HOLDER, FUSE (CND) R105 1-216-077-11 RES-CHIP 15K 5% 1/10W

< CAPACITOR > R106 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

R110 1-216-025-11 RES-CHIP 100 5% 1/10W
C901 1-101-005-00 CERAMIC 22000PF 50V R111 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
C902 1-101-005-00 CERAMIC 22000PF 50V R201 1-216-077-11 RES-CHIP 15K 5% 1/10W
C903 1-101-005-00 CERAMIC 22000PF 50V R202 1-216-023-00 METAL CHIP 82 5% 1/10W
C904 1-101-005-00 CERAMIC 22000PF 50V
R203 1-216-097-11 RES-CHIP 100K 5% 1/10W
< DIODE > R204 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R205 1-216-077-11 RES-CHIP 15K 5% 1/10W
D901 8-719-063-79 DIODE 1N4002B R206 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
D902 8-719-063-79 DIODE 1N4002B R210 1-216-174-00 RES-CHIP 100 5% 1/8W
D903 8-719-063-79 DIODE 1N4002B
D904 8-719-063-79 DIODE 1N4002B R211 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
************************************************************* R301 1-216-121-11 RES-CHIP 1M 5% 1/10W
R302 1-216-214-00 RES-CHIP 4.7K 5% 1/8W
* A-3322-448-A TC BOARD, COMPLETE R303 1-216-214-00 RES-CHIP 4.7K 5% 1/8W
******************* R304 1-216-198-11 RES-CHIP 1K 5% 1/8W

< CAPACITOR > R305 1-216-180-00 RES-CHIP 180 5% 1/8W

R306 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
C101 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V R307 1-216-150-11 RES-CHIP 10 5% 1/8W
C102 1-104-664-11 ELECT 47uF 20% 10V R308 1-216-081-00 METAL CHIP 22K 5% 1/10W
C103 1-162-587-11 CERAMIC CHIP 0.039uF 10% 25V R309 1-216-166-00 RES-CHIP 47 5% 1/8W
C104 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C105 1-163-243-11 CERAMIC CHIP 47PF 5% 50V < SWITCH >

C106 1-126-960-11 ELECT 1uF 20% 50V S301 1-762-565-11 SWITCH, SLIDE (REC/PB)
C201 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
C202 1-104-664-11 ELECT 47uF 20% 10V < TRANSFORMER >
C203 1-162-587-11 CERAMIC CHIP 0.039uF 10% 25V
C204 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION
*************************************************************
C205 1-163-243-11 CERAMIC CHIP 47PF 5% 50V
C206 1-126-960-11 ELECT 1uF 20% 50V * A-3322-456-A TUNER BOARD, COMPLETE
C301 1-104-665-11 ELECT 100uF 20% 10V *********************
C302 1-104-665-11 ELECT 100uF 20% 10V
C303 1-104-665-11 ELECT 100uF 20% 10V < CAPACITOR >

C304 1-104-664-11 ELECT 47uF 20% 10V C4 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C305 1-137-431-11 MYLAR 560PF 5% 50V C8 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C306 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C9 1-163-098-00 CERAMIC CHIP 16PF 5% 50V
C307 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V C10 1-126-960-11 ELECT 1uF 20% 50V
C11 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
< CONNECTOR >
C12 1-126-963-11 ELECT 4.7uF 20% 50V
CNP301 1-568-830-11 CONNECTOR, FFC 11P C14 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C15 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V

The components identified by Les composants identifiés par une

mark 0 or dotted line with mark. marque 0 sont critiques pour la
0 are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une piéce
specified. portant le numéro spécifié.

– 62 –
 TUNER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C16 1-126-960-11 ELECT 1uF 20% 50V CT3 1-141-304-21 CAP, TRIMMER 10PF
C17 1-126-960-11 ELECT 1uF 20% 50V
C18 1-126-934-11 ELECT 220uF 20% 10V < DIODE >
C19 1-163-243-11 CERAMIC CHIP 47PF 5% 50V
C20 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V D1 8-719-078-48 DIODE KV1471ETR1-3
D2 8-719-078-48 DIODE KV1471ETR1-3
C21 1-126-960-11 ELECT 1uF 20% 50V D3 8-719-050-69 DIODE KV1520N
C22 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V D10 8-719-988-61 DIODE 1SS355TE-17
C23 1-126-960-11 ELECT 1uF 20% 50V D11 8-719-988-61 DIODE 1SS355TE-17
C24 1-163-003-11 CERAMIC CHIP 330PF 10% 50V
C26 1-163-251-11 CERAMIC CHIP 100PF 5% 50V < JUMPER RESISTOR >

C27 1-163-251-11 CERAMIC CHIP 100PF 5% 50V FB1 1-216-295-00 SHORT 0

C28 1-104-665-11 ELECT 100uF 20% 10V
C30 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V < IC >
C31 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C32 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V IC1 8-759-662-67 IC A2149N
IC2 8-759-483-40 IC C72137M-TLM
C33 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C34 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V < JUMPER RESISTOR >
C35 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C41 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V JC8 1-216-296-00 SHORT 0
C42 1-163-129-00 CERAMIC CHIP 330PF 5% 50V JC9 1-216-296-00 SHORT 0
JC10 1-216-296-00 SHORT 0
C44 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V JC14 1-216-296-00 SHORT 0
C47 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V JC15 1-216-296-00 SHORT 0
C51 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C52 1-163-098-00 CERAMIC CHIP 16PF 5% 50V JC16 1-216-296-00 SHORT 0
C53 1-136-171-00 MYLAR 0.33uF 5% 50V JC18 1-216-295-00 SHORT 0
JC19 1-216-296-00 SHORT 0
C54 1-126-934-11 ELECT 220uF 20% 10V JC20 1-216-296-00 SHORT 0
C55 1-163-251-11 CERAMIC CHIP 100PF 5% 50V JC21 1-216-295-00 SHORT 0
C56 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C57 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V JC23 1-216-296-00 SHORT 0
C58 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC24 1-216-295-00 SHORT 0
JC27 1-216-296-00 SHORT 0
C59 1-163-251-11 CERAMIC CHIP 100PF 5% 50V JC28 1-216-296-00 SHORT 0
C60 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V JC29 1-216-296-00 SHORT 0
C61 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C62 1-163-251-11 CERAMIC CHIP 100PF 5% 50V JC30 1-216-296-00 SHORT 0
C63 1-163-251-11 CERAMIC CHIP 100PF 5% 50V JC31 1-216-296-00 SHORT 0
JC33 1-216-296-00 SHORT 0
C64 1-163-251-11 CERAMIC CHIP 100PF 5% 50V JC38 1-216-296-00 SHORT 0
C66 1-163-251-11 CERAMIC CHIP 100PF 5% 50V JC39 1-216-296-00 SHORT 0
C68 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C77 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC40 1-216-296-00 SHORT 0
C80 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC41 1-216-296-00 SHORT 0
JC42 1-216-295-00 SHORT 0
C93 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JC43 1-216-296-00 SHORT 0
C95 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V JC44 1-216-295-00 SHORT 0

< FILTER > < COIL >

CF2 1-760-738-61 FILTER, CERAMIC L1 1-416-533-11 COIL, AIR-CORE

CF4 1-781-749-11 FILTER, AM CERAMIC L2 1-416-509-11 COIL, AIR-CORE
L3 1-501-923-21 ANTENNA, FERRITE-ROD (AM)
< CONNECTOR > L4 1-411-234-21 COIL, AM OSC
L11 1-414-142-11 INDUCTOR 1uH
* CNP1 1-785-663-11 PIN, CONNECTOR (PC BOARD) 11P
L21 1-410-509-11 INDUCTOR 10uH
< TRIMMER >

CT1 1-141-227-00 CAP, TRIMMER 20PF

– 63 –
CFD-S22/S32
TUNER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< RESISTOR > MISCELLANEOUS
***************
R1 1-216-037-00 METAL CHIP 330 5% 1/10W
R2 1-216-033-00 METAL CHIP 220 5% 1/10W 8 1-792-206-11 WIRE, PARALLEL (6 CORE) (S22)
R3 1-216-073-00 METAL CHIP 10K 5% 1/10W 8 1-792-207-11 WIRE, PARALLEL (8 CORE) (S32)
R4 1-216-073-00 METAL CHIP 10K 5% 1/10W 102 1-792-204-11 WIRE, PARALLEL (11 CORE)
R5 1-216-295-00 SHORT 0 111 1-792-205-11 WIRE, PARALLEL (21 CORE)
118 1-452-899-11 MAGNET
R10 1-216-166-00 RES-CHIP 47 5% 1/8W
R11 1-216-061-00 METAL CHIP 3.3K 5% 1/10W 126 1-792-209-11 WIRE, PARALLEL (16 CORE)
R13 1-216-206-00 RES-CHIP 2.2K 5% 1/8W 128 1-792-208-11 WIRE, PARALLEL (17 CORE)
R24 1-216-033-00 METAL CHIP 220 5% 1/10W 0 251 8-848-483-05 PICK-UP, OPTICAL KSS-213C/Q-RP
R25 1-216-001-00 METAL CHIP 10 5% 1/10W 254 X-2626-202-1 CHASSIS ASSY (MB), MOTOR (SPINDLE)
(INCLUDING M701)
R30 1-216-077-11 RES-CHIP 15K 5% 1/10W ANT1 1-501-883-21 ANTENNA, TELESCOPIC
R31 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R32 1-216-097-11 RES-CHIP 100K 5% 1/10W 0 F902 1-576-107-12 FUSE (3.15A) (CND)
R40 1-216-105-11 RES-CHIP 220K 5% 1/10W HE301 1-543-876-11 HEAD (ERASE)
R41 1-216-073-00 METAL CHIP 10K 5% 1/10W HRP301 1-500-454-11 HEAD, MAGNETIC (RECORD/PLAYBACK)
M301 A-3320-446-A MOTOR ASSY (CAPSTAN/REEL)
R50 1-216-198-11 RES-CHIP 1K 5% 1/8W M702 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED)
R51 1-216-073-00 METAL CHIP 10K 5% 1/10W
R53 1-216-075-00 METAL CHIP 12K 5% 1/10W S304 1-692-302-11 SWITCH, LEAF (TAPE PLAY)
R54 1-216-043-11 RES-CHIP 560 5% 1/10W S501 1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR
R56 1-216-041-00 METAL CHIP 470 5% 1/10W OPEN/CLOSE)
SP301 1-529-215-11 SPEAKER (10cm) (L-CH) (US,CND)
R58 1-216-206-00 RES-CHIP 2.2K 5% 1/8W SP301 1-529-340-11 SPEAKER (10cm) (L-CH) (E92,MX)
R59 1-216-206-00 RES-CHIP 2.2K 5% 1/8W SP302 1-529-215-11 SPEAKER (10cm) (R-CH) (US,CND)
R60 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R61 1-216-206-00 RES-CHIP 2.2K 5% 1/8W SP302 1-529-340-11 SPEAKER (10cm) (R-CH) (E92,MX)
R63 1-216-222-00 RES-CHIP 10K 5% 1/8W 0 T901 1-433-576-11 TRANSFORMER, POWER
**************************************************************
R65 1-216-073-00 METAL CHIP 10K 5% 1/10W
R91 1-216-198-11 RES-CHIP 1K 5% 1/8W ACCESSORIES & PACKING MATERIALS
R92 1-216-198-11 RES-CHIP 1K 5% 1/8W ********************************
R93 1-216-296-00 SHORT 0
R94 1-216-049-11 RES-CHIP 1K 5% 1/10W 0 1-557-287-11 CORD, POWER (E92,MX)
0 1-690-952-11 CORD, POWER (CND)
< TRANSFORMER > 0 1-783-878-11 CORD, POWER (US)
3-027-153-11 LID, BATTERY CASE (for RMT-CS32A) (S32)
T1 1-435-333-11 TRANSFORMER, IF 3-043-356-11 MANUAL, INSTRUCTION (ENGLISH)
T2 1-419-465-11 COIL (DET)
3-043-356-21 MANUAL, INSTRUCTION (FRENCH) (CND)
< VIBRATOR > 3-044-465-61 MANUAL, INSTRUCTION (SPANISH) (E92,MX)
A-3258-003-A REMOTE CONTROLLER (RMT-CS32A) (S32)
X1 1-781-592-11 VIBRATOR, CRYSTAL (75kHz) *************************************************************
*************************************************************
**************
HARDWARE LIST
**************

#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S

#2 7-685-648-79 SCREW +BVTP 3X12 TYPE2 N-S
#3 7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S
#4 7-685-851-04 SCREW +BVTT 2X4 (S)
#5 7-621-255-45 SCREW +P 2X6

#6 7-682-548-04 SCREW +B 3X8

#7 7-685-533-19 SCREW +BTP 2.6X6 TYPE2 N-S
#8 7-621-770-87 SCREW +B 2.6X5

The components identified by Les composants identifiés par une

mark 0 or dotted line with mark marque 0 sont critiques pour la
0 are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une piéce
specified. portant le numéro spécifié.

Sony Corporation
2000B0437-1
9-927-674-11 Personal Audio Division Company Printed in Japan C2000. 2
– 64 – Published by General Engineering Dept.