Service Manual: HCD-RG121

HCD-RG121
SERVICE MANUAL AEP Model

UK Model
Ver 1.0 2004.04
E Model
Australian Model
• HCD-RG121 is the tuner, deck, CD and

amplifier section in MHC-RG121.
Model Name Using Similar Mechanism New

CD CD Mechanism Type CDM74-K6BD80
Section
Optical Pick-up Name KSM-213DCP/Z-NP
Tape deck Model Name Using Similar Mechanism New

Section Tape Transport Mechanism Type CWM43FF-05
SPECIFICATIONS
Amplifier section Tape deck section

AUDIO POWER SPECIFICATIONS Recording system 4-track 2-channel, stereo
Frequency response 50 – 13,000 Hz (±3 dB),
DIN power output (rated): 50 + 50 watts (6 ohms at using Sony TYPE I
1 kHz, DIN) cassettes
Continuous RMS power output (reference):
65 + 65 watts (6 ohms at Tuner section
1 kHz, 10% THD) FM stereo, FM/AM superheterodyne tuner
Music power output (reference): FM tuner section
130 + 130 watts (6 ohms at Tuning range
1 kHz, 10% THD) North American model: 87.5 – 108.0 MHz
The following measured at AC 120, 127, 220, 240 V (100-kHz step)
50/60 Hz Russian model: 65.0 – 74.0 MHz
DIN power output (rated): 50 + 50 watts (6 ohms at (There is no stereo effect.
1 kHz, DIN) 10-kHz step)
Continuous RMS power output (reference): 87.5 – 108.0 MHz
60 + 60 watts (6 ohms at (50-kHz step)
1 kHz, 10% THD) Other models: 87.5 – 108.0 MHz
(50-kHz step)
CD player section Antenna FM lead antenna
System Compact disc and digital Antenna terminals 75 ohms unbalanced
audio system Intermediate frequency 10.7 MHz
Laser Semiconductor laser
(λ=780 nm)
Emission duration: – Continued on next page –
continuous
Frequency response 2 Hz – 20 kHz (±0.5 dB)
Wavelength 780 – 790 nm
Signal-to-noise ratio More than 90 dB
Dynamic range More than 90 dB
MINI HI-FI COMPONENT SYSTEM
9-877-658-01 Sony Corporation
2004D1679-1 Home Audio Company
© 2004.04 Published by Sony Engineering Corporation
HCD-RG121
AM tuner section
Tuning range
NOTES ON HANDLING THE OPTICAL PICK-UP
Pan-American models: 530 – 1,710 kHz BLOCK OR BASE UNIT
(with the tuning interval
set at 10 kHz) The laser diode in the optical pick-up block may suffer electrostatic
531 – 1,710 kHz break-down because of the potential difference generated by the
(with the tuning interval charged electrostatic load, etc. on clothing and the human body.
set at 9 kHz) During repair, pay attention to electrostatic break-down and also
European, Russian and Saudi Arabian models:
use the procedure in the printed matter which is included in the
531 – 1,602 kHz (with the
tuning interval set at
repair parts.
9 kHz) The flexible board is easily damaged and should be handled with
Other models: 530 – 1,710 kHz care.
set at 10 kHz) NOTES ON LASER DIODE EMISSION CHECK
531 – 1,602 kHz The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
set at 9 kHz)
Antenna AM loop antenna
up block. Therefore, when checking the laser diode emission,
Antenna terminals External antenna terminal observe from more than 30 cm away from the objective lens.
Intermediate frequency 450 kHz
Laser component in this product is capable
General of emitting radiation exceeding the limit for
Power requirements Class 1.
European and Russian models:
110 watts
0.25 watts (at the Power
Saving Mode)
Other models: 110 watts
Dimensions (w/h/d) incl. projecting parts and controls

Amplifier/Tuner/Tape/CD section:
Approx. 280 × 327 ×
425 mm This appliance is classified as a CLASS 1 LASER product. The
Mass CLASS 1 LASER PRODUCT MARKING is located on the rear
European and Russian models: exterior.
Approx. 8.5 kg
Other models: Approx. 8.5 kg
CAUTION
Design and specifications are subject to change Use of controls or adjustments or performance of procedures
without notice. other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement

• Never reuse a disconnected chip component. The release method of a CD disc tray LOCK function
• Notice that the minus side of a tantalum capacitor may be
damaged by heat. There is a disc lock function for the disc theft prevention for a
demonstration at a shop front in this machine.
Flexible Circuit Board Repairing Procedue:
• Keep the temperature of soldering iron around 270˚C 1. Press the ?/1 button to turn the set on.
during repairing. 2. Press two buttons of x and Z (EJECT) simultaneously for
• Do not touch the soldering iron on the same conductor of the five seconds.
circuit board (within 3 times). 3. The message “LOCKED” is displayed and the tray is locked.
• Be careful not to apply force on the conductor when soldering (Even if exiting from this mode, the tray is still locked.)
or unsoldering. 4. Press two buttons of x and Z (EJECT) simultaneously for
five seconds again.
5. The message “UNLOCKED” is displayed and the tray is
unlocked.
6. To exit from this mode, press the ?/1 button to turn the set
off.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
2
HCD-RG121
TABLE OF CONTENTS
Unleaded solder 1. SERVICE POSITION ............................................... 4

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead. 2. GENERAL ................................................................... 6
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.) 3. DISASSEMBLY
3-1. Cover (Top) ........................................................... 9
3-2. CD Door ................................................................ 9
: LEAD FREE MARK 3-3. Front Panel Section ............................................... 10
Unleaded solder has the following characteristics. 3-4. CD Mechanism Deck (CDM74-K6BD80) ............ 10
• Unleaded solder melts at a temperature about 40°C higher than 3-5. Tape Mechanism Deck, GAME JACK Board ....... 11
ordinary solder. 3-6. PANEL Board ........................................................ 11
Ordinary soldering irons can be used but the iron tip has to be 3-7. Back Panel Section, SUB-TRANS Board ............. 12
applied to the solder joint for a slightly longer time. 3-8. Power Transformer ................................................ 12
Soldering irons using a temperature regulator should be set to 3-9. MAIN Board ......................................................... 13
about 350°C. 3-10. AMP Board ........................................................... 13
Caution: The printed pattern (copper foil) may peel away if the 3-11. BD80A Board ........................................................ 14
heated tip is applied for too long, so be careful! 3-12. CONNECT Board ................................................. 14
• Strong viscosity 3-13. DRIVER Board, SW Board .................................. 15
Unleaded solder is more viscous (sticky, less prone to flow) than 3-14. Optical PICK-UP (KSM-213DCP/Z-NP) ............. 15
ordinary solder so use caution not to let solder bridges occur 3-15. SENSOR Board ..................................................... 16
such as on IC pins, etc. 3-16. MOTOR (TB) Board ............................................. 16
• Usable with ordinary solder 3-17. MOTOR (LD) Board ............................................. 17
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. 4. TEST MODE ............................................................... 18
5. DIAGRAMS
5-1. Block Diagram – PANEL Section – ...................... 22
5-2. Block Diagrams – MAIN Section – ...................... 23
5-3. Block Diagrams – BD/DRIVER Section – ........... 24
5-4. Printed Wiring Board – BD80A Section – ............ 25
5-5. Schematic Diagram – BD80A Section – ............... 26
5-6. Printed Wiring Board
– CD MECHANISM Section – ............................. 27
5-7. Schematic Diagram
– CD MECHANISM Section – ............................. 28
5-8. Printed Wiring Board – MAIN Section – .............. 29
5-9. Schematic Diagram – MAIN Section (1/2) – ........ 30
5-10. Schematic Diagram – MAIN Section (2/2) – ........ 31
5-11. Printed Wiring Board
– PANEL COMB Section – ................................... 32
5-12. Schematic Diagram
– PANEL COMB Section – ................................... 33
5-13. Printed Wiring Board – PANEL Section – ............ 34
5-14. Schematic – PANEL Section (1/2) – ..................... 35
5-15. Schematic – PANEL Section (2/2) – ..................... 36
5-16. Printed Wiring Board – TRANS Section – ........... 37
5-17. Printed Wiring Board – AMP Section – ................ 38
5-18. Schematic Diagram – AMP POWER Section – .... 39
5-19. IC Pin Function Description .................................. 42
6. EXPLODED VIEWS
6-1. MAIN Section ....................................................... 48
6-2. Front Panel Section ............................................... 49
6-3. MAIN Board Section ............................................ 50
6-4. CD Mechanism Deck Section-1
(CDM74-K6BD80) ............................................... 51
6-5. CD Mechanism Deck Section-2
(CDM74-K6BD80) ............................................... 52
7. ELECTRICAL PARTS LIST .................................. 53
3
HCD-RG121
SECTION 1
SERVICE POSITION
• SERVICE POSITION-1 (AMP BOARD)
To inspect the AMP board, turn both of the front panel and the
CD mechanism deck so that the left side of the product faces
down.
CD mechanism deck
front panel
AMP board
4
HCD-RG121
• SERVICE POSITION-2 (BD80A BOARD)
Remove the CD mechanism deck and place it on top of the

pedestal as shown.
Inspect the BD80A bard in this set up.
BD80A board
CD mechanism deck
5
HCD-RG121
SECTION 2 This section is extracted
from instruction manual.
GENERAL
List of button locations and reference pages
How to use this page Illustration number

r
Use this page to find the location of buttons and other TAPE A/B ed (18, 19, 20, 24)
parts of the system that are mentioned in the text. R R
Name of button/part Reference page
Main unit
ALPHABETICAL ORDER BUTTON DESCRIPTIONS
A–O P–Z ?/1 (power) 1 (8, 16, 27, 30, 33,

35)
ALBUM +1) qh (12, 14, 19) P FILE qd (22)
X (pause) wg (12, 19)
ALBUM –1) wg (12, 14, 19) PHONES jack ql
Z (eject) qf (11)
CD eg (9, 11, 14, 19, 20) PLAY MODE wl (12, 14, 18, 19,
20, 35) PUSH Z (deck B) (eject) qg (18)
CD SYNC wj (19)
Power illuminator2) qk (28) x (stop) wg (12, 19, 24, 35)
Deck A wk (18)
PRESET EQ qd (22) M (fast forward) qh (12, 19)
Deck B qj (18, 19, 20, 24)
REC PAUSE/START wj (19, 20, H or hH3) (play) qh (12, 18,
DISC 1 – 3 q; (12, 14, 35)
23, 24) 19)
DISC SKIP/EX-CHANGE qs
Remote sensor 4 m (rewind) wg (12, 19)
(11, 12, 14, 19)
SURROUND 8 (23) Z PUSH (deck A) (eject) e; (18)
Disc tray 9 (11) 1) MHC-GX750/GX450/RG555/
DISPLAY 2 (17, 27, 28) TAPE A/B ed (18, 19, 20, 24)
RG551S/RG444S/RG441/
Display window 5 TUNER/BAND ef (15, 16, 20)
RG333/RG222/RG221/RX550
EFFECT ON/OFF 8 (22) TUNING MODE wl (15, 16, 35)
only
ENTER qa (14, 15, 22) TUNING + qh (15, 16) 2) MHC-GX750/GX450/RG555/
EQ BAND 7 (22) TUNING – wg (15, 16)
RG551S/RG444S/RG441/
GAME es (20, 23, 30) VIDEO/MD3) ea (20, 30)
RG333/RX550 only
GAME INPUT AUDIO L/R jacks VOLUME control w; (21) 3)
MHC-RG555 only
wd (20, 29) WIRELESS4) ea (32) 4) MHC-GX750 only
GAME INPUT VIDEO jack wf
(29) 1 2345 6 78 9
GAME MIXING wh (23)
GROOVE 8 (21)
ILLUMINATION2) 3 (28)
MIC jack3) ws (24)
MIC LEVEL3) wa (24) q;
Operation Dial eg
(– EQ +/l L) 6 (12,
ef qa
14, 19, 22) j J
ed ALBUM
S
ALBUM
H
qs
h
es s
TUNING TUNING
qd
ea qf
e; qg
wl qh
wk qj
wj qk
ql
wh wg wf wd ws wa w;
6
HCD-RG121
Remote control
ALPHABETICAL ORDER BUTTON DESCRIPTIONS
A–E F–Z ?/1 (power) 1 (8, 26)

ALBUM –* qd (12, 14) FM MODE 4 (17) m/M (rewind/fast forward)
ALBUM +* qa (12, 14) 7 (12, 19)
FUNCTION 6 (11, 14, 15, 16)
CD qk (11, 14) –/+ (tuning) qh (15)
PLAY MODE w; (12, 14, 18)
CLEAR qg (14) ./> (go back/go forward)
REPEAT 4 (13)
qh (10, 12, 19)
CLOCK/TIMER SELECT 2 SLEEP ws (25)
(26, 27) N (play) 8 (12, 18)
TAPE qj
CLOCK/TIMER SET 3 (10, 25, X (pause) 8 (12, 19)
TUNER BAND 5 (15, 16)
26) x (stop) 8 (12, 19)
TUNER MEMORY ql (15)
DISC SKIP q; (12, 14) TUNING MODE w; (15, 16)
DISPLAY wa (17, 27, 28) * MHC-GX750/GX450/RG555/
VOLUME +/– qs (21, 25)
ENTER 9 (10, 14, 15, 25, 26) RG551S/RG444S/RG441/
EQ qf (22) RG333/RG222/RG221/RX550
only
ws 1
wa 2
w; 3 Setting the clock
ql 4
Use buttons on the remote for the operation.
qk 5
qj 6 1 Press ?/1 to turn on the system.
qh 7 2 Press CLOCK/TIMER SET.
8
3 Press . or > repeatedly to set the
hour.
qg 9 4 Press ENTER.
qf q; 5 Press . or > repeatedly to set the

minute.
qd qa 6 Press ENTER.
The clock starts working.
qs
To adjust the clock
1 Press CLOCK/TIMER SET.
2 Press . or > repeatedly to select
“CLOCK SET”, then press ENTER.
3 Do the same procedures as step 3 to 6
above.
Notes
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
7
HCD-RG121
SECTION 3
DISASSEMBLY
Note: Disassemble the unit in the order as shown below.
SET
3-1.COVER (TOP)
(Page 9)
3-2.CD DOOR
(Page 9)
3-3.FRONT PANEL SECTION

(Page 10)
3-4.CD MECHANISM DECK 3-5.TAPE MECHANISM DECK, 3-6.PANEL BOARD

(CDM74-K6BD80) GAME JACK BOARD (Page 11)
(Page 10) (Page 11)
3-11.BD80A BOARD 3-12.CONNECT BOARD 3-14.OPTICAL PICK-UP 3-15.SENSOR BOARD

(Page 14) (Page 14) (KSM-213DCP/Z-NP) (Page 16)
(Page 15)
3-7.BACK PANEL SECTION, 3-13.DRIVER BOARD, 3-16.MOTOR (TB) BOARD

SUB-TRANS BOARD SW BOARD (Page 16)
(Page 12) (Page 15)
3-17.MOTOR (LD) BOARD

(Page 17)
3-8.POWER TRANSFORMER 3-9.MAIN BOARD

(Page 12) (Page 13)
3-10.AMP BOARD
(Page 13)
8
HCD-RG121
3-1. COVER (TOP)

qa two screws (+BVTP 3 × 10)
qs
qf cover (top)
6 two screws (Case 3 TP2)

cover (Side-L)
8 screw qs
(+BVTP 3 × 10)
qd
q;
cover (Side-R)
5
9 screw
(+BVTP 3 × 10)
3 screw
7 screw (case 3 TP2) (+BVTP 3 × 10)
1 two screws
(case 3 TP2)
4 screw
(+BVTP 3 × 10)
2 screw (Case 3 TP2)
3-2. CD DOOR
3 two claws
4 CD door
CD mechanism deck (CDM74B)
1 Turn the pulley to the direction of arrow.
Front panel side
pulley
2 Pull-out the disc tray.
9
HCD-RG121
3-3. FRONT PANEL SECTION
4 screw (+BVTP 3 × 8)
0 connector 3p (CN314C)
8 wire (flat type) 7 core (CN253)
6 connector 2p (CN805)
qa connector 3p (CN112)
qs connector 8p (CN103)
qd front panel section
1 three screws (+BVTP 3 × 8)
3-4. CD MECHANISM DECK (CDM74-K6BD80)
1 three screws (+BVTP 3 × 10)
4 CD mechanism deck (CDM74-K6BD80)

10
HCD-RG121
3-5. TAPE MECHANISM DECK, GAME JACK BOARD
3 TRANSRATION board
2 six screws
(+BVTP 2.6 × 8)
6 GAME JACK board 5 two screws

(+BVTP 2.6 × 8)
4 tape mechanism deck
3-6. PANEL BOARD
2 seven claws
5 PANEL board
1 ten screws
(+BVTP 2.6 × 8)
11
HCD-RG121
3-7. BACK PANEL SECTION, SUB-TRANS BOARD
9 back panel section
8 SUB-TRANS board 7 connector

2p (CN901)
6 two screws
(+BVTT 3 × 10)
5 two screws
(+BVTT 3 × 10)
2 connector 1 connector
2p (CN906) 2p (CN904)
4 two screws
3 wire (flat type) (+BVTP 3 × 10)
15 core (CN101)
3-8. POWER TRANSFORMER
5 four screws
(+ITC 4 × 8)
6 power transformer
3 screw
1 connector (+BVIT 3 × 8R)
3p (CN905)
2 connector
10p (CN907)
4 earth wire
12
HCD-RG121
3-9. MAIN BOARD
4 MAIN board
1 connector
10p (CN907)
Main board
3 connector
13p (CN441)
2 two screws
(+BVTP 3 × 8)
3-10. AMP BOARD
1 two screws
(+BVTT 3 × 8)
2 screw
3 two screws
(+BVTP 3 × 14)
(+BVIT 3 × 8R)
4 two screws 5 heat sink

(transistor)
6 AMP board
13
HCD-RG121
3-11. BD80A BOARD
3 screw
(+BVTP 2.6 × 8)
speacer
5 BD80A board

4 Remove soldering from the four points.
3-12. CONNECT BOARD

2 two screws
(+BVTP 2.6 × 8)
3 CONNECT board
14
HCD-RG121
3-13. DRIVER BOARD, SW BOARD
1 two screws
(+BTTP (M2.6))
3 connector
4p (CN703)
4 DRIVER board 5 screw
(+BTTP (M2.6))
6 SW board
2 wire (flat type) 5p (CN702)
3-14. OPTICAL PICK-UP (KSM-213DCP/Z-NP)
1 floating screw
(+PTPWH M2.6)
2 holder (213) ASSY 6 two insulators

qa
qh optical pick-up
(KSM-213DCP/Z-NP)
5 two coil springs
0 two insulators (insulator)
3 screw
9 two coil springs
(BVTT M2.6)
(insulator)
4 floating screw
8 two stoppers (BU)
(+PTPWH M2.6)
7 two screws qf CN101 (flat type)

(BVTT M2.6)
qg BD80A board
qd Remove the four solderings of motor.

qs screw (+BVTP 2.6x 8)
15
HCD-RG121
3-15. SENSOR BOARD
1 floating screw
(+PTPWH M2.6)
2 tray 8 screw
(+BTTP (M2.6))
3 belt (table)
0 SENSOR board
4 foating screw
(+PTPWH M2.6)
5 pulley (table)
6 floating screw 9 connector

(+PTPWH M2.6) (CN731)
7 gear (geneva)
3-16. MOTOR (TB) BOARD
2 stopper
1 stopper
5 table motor assy (M741)
7 MOTOR (TB) board
6 Remove the two solderings of motor.
5 two screws
(+BTTP (M2.6))
16
HCD-RG121
3-17. MOTOR (LD) BOARD
2 two screws
(+BTTP (M2.6))
4 Remove the two solderings of motor.
3 MOTOR (LD) board
5 loading motor assy (M751)
1 belt (loading)
17
HCD-RG121
SECTION 4
TEST MODE
[Change-over of AM Tuner Step between 9 kHz and 2) Error display
10 kHz] Disc error
• A step of AM channels can be changed over between 9 kHz and Display Error
10 kHz. E00D01022 Focus error (No disc)
E00D02022 Sub Q error (Focus is good)
Procedure:
1. Press ?/1 button to turn the set ON. E00D02023 TOC reading error
2. Select the function “TUNER”, and press TUNER/BAND E00D02014 Access error (Unable within regular time)
button to select the BAND “AM”.
3. Press ?/1 button to turn the set OFF. Mechanism error
4. Press TUNER/BAND and ?/1 buttons simultaneously, and Display Error
the display of fluorescent indicator tube changes to “AM 9 k E00M__E_0 Error during opening tray
STEP” or “AM 10 k STEP”, and thus the channel step is changed
E00M__C_2 EX-CHANGE disc error
over.
E00M__D_0 Error during closing tray
[Cold Reset] E00M__F_3 EX-OPEN error
• The cold reset clears all data including preset data stored in the E00M__D_5 EX-CLOSE error
RAM to initial conditions. Execute this mode when returning E00M__C_2 Chuck-up error
the set to the customer. E00M__C_3 Unchucking error
Procedure:
1. Press three buttons x , PLAY MODE/TUNING MODE , 3. Aging mode in Tape Deck section
and DISC1 simultaneously. 1) Operation during aging mode
2. The fluorescent indicator tube displays “COLD RESET” and • In the agining mode, the program is excuted in the following
the set is reset. sequence.
Step Operation Display
[Aging Mode]
1 Rewind the TAPE A TAPE AAG-1
This mode can be used for operation check of CD section and tape
deck section. 2 Rewind the TAPE B TAPE BAG-2
• If an error occurred: 3 Play the TAPE A (1 minute) TAPE AAG-2
The aging operation stops and is displayed status. 4 Stop the TAPE A (1 second) TAPE AAG-3
• If no error occurs: 5 Play the TAPE A (3 minutes) TAPE AAG-4
The aging operation continues repeatedly. 6 Rewind(AMS) the TAPE A TAPE AAG-5
7 F.F.(AMS) the TAPE A TAPE AAG-6
1. Operating method of Aging Mode
8 Play the TAPE B (1 minute) TAPE BAG-2
Turn on the main power and select “CD” of the function.
1) Set three discs in tray. Select ALL DISCS, and REPEAT OFF. 9 Stop the TAPE B (1 second) TAPE BAG-3
2) Load the tapes recording use into both decks. 10 Record the TAPE B (3 minutes) TAPE BAG-4
3) Press three buttons x , PLAY MODE/TUNING MODE , 11 Rewind(AMS) the TAPE B TAPE BAG-5
and EX-CHANGE simultaneously. 12 F.F.(AMS) the TAPE B TAPE BAG-6
4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [Cold Reset]. 2) Error display
• If error occurred, the display remains like “TAPE BAG-2”.
2. Aging mode in CD section
1) Operation during aging mode 4. Exiting from the aging mode
• In the agining mode ,the program is excuted in the following • Be sure to perform Cold Reset to exit from the aging mode.
sequence.
(1) The disc tray opens and closes.
(2) The disc tray turns to select a disc 3.
(3) The pick-up accesses to the first track, and plays 3 seconds.
(4) The pick-up accesses to the last track, and plays 3 seconds.
(5) The disc tray opens and closes.
(6) The disc tray turns to select a disc 1.
(7) The same operation starts like step (3).
(8) After a disc 1 aging operation, a disc 2 is selected.
(9) When an aging operation of a disc 3 is completed, the display
“AGING ∗∗∗∗” value increases.
(10) If no error occurs, the aging operation continues repeatedly.
18
HCD-RG121
[PANEL Test Mode] [MC Test Mode]

• All fluorecent segments and LEDs are tested. • This mode is used to test the function of the equalizer.
• Keyboard check.
Procedure:
Procedure: 1. Press ?/1 button to turn the set ON.
1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x ,
2. To enter the test mode, press the three buttons x , PLAY MODE/TUNING MODE and DISC 3 simultaneously.
PLAY MODE/TUNING MODE and ENTER simultaneously. 3. Press the EQ+ button.
3. All segments and LEDs (without STANDBY LED) are turned The function of the equalizer is set to “MIN”.
on. 4. Press the EQ– button.
4. Press X and ENTER buttons simultaneously, and the key The function of the equalizer is set to “MAX”.
check mode is activated. 5. Press the PRESET EQ button.
5. The message “KEY 0 0 0” is displayed. The function of the equalizer is set to “EQ FLAT”.
Each time a button is pressed, the key code number is displayed. 6. MASTER VOLUME up and down.
6. Press X and ENTER buttons simultaneously, and the key “VOLUME MIN”, “VOLUME 16”, “VOLUME MAX” is
count mode is activated. displayed.
7. The message “KEYCNT 0” is displayed. 7. Press GROOVE button.
Each time a button is pressed, “KEYCNT 0” value increased. The message “VACS OFF” on “VACS ON” is dislayed.
However, once a button is pressed, it is no longer taken into 8. To exit from this mode, press ?/1 button to turn the set OFF.
account.
8. Press X and ENTER buttons simultaneously, and the head [CD Ship Mode (LOCK) ]
phone detect mode is activated. • This mode moves the pick-up to the position durable to vibra-
9. The message “H_P OFF” is displayed when a headphone jack tion. Use this mode when returning the set to the customer after
is not inserted. repair.
“H_P ON ” is displayed when a headphone jack is inserted.
10. Press X and ENTER buttons simultaneously, and the volume Procedure:
control detect mode is activated. 1. Press ?/1 button to turn the set ON.
11. The message “VOLUME FLAT” is displayed. 2. Select the function “CD”.
“VOLUME UP” is displayed if rotating MASTER VOLUME 3. Press ?/1 button to turn the set OFF.
knob clockwise, or “VOLUME DOWN” is displayed if rotating 4. Press CD button and ?/1 button simultaneously.
counterclockwise. 5. The “STANDBY” display blinks instantaneously, and the CD
12. To exit from the GC test mode after the head phone detect mode, ship mode is set.
press X and ENTER buttons simultaneously.
[CD Ship (LOCK) & COLD RESET MODE]
[Version and Destination Display Mode] Procedure:
• The version or destination is displayed. 1. Press ?/1 button to turn the set ON.
2. Select the function “CD”.
Procedure: 3. Press ?/1 button to turn the set OFF.
1. Press ?/1 button to turn the set ON. 4. Press three buttons x , CD and DISPLAY simultaneously.
2. To enter the test mode, press the three buttons x , 5. The “STANDBY” display blinks instantaneously and CD ship
PLAY MODE/TUNING MODE and DISC2 simultaneously. mode is set.
3. The destination is displayed. 6. The fluorescent indicator tube displays “COLD RESET” and
4. Press DISPLAY buttons simultaneously. the set is reset.
5. The version is displayed.
6. To exit from this mode, press ?/1 button to turn the set OFF. [Disc Tray Lock]
Procedure:
[CD Service Mode] 1. Press the ?/1 button to turn the set ON.
• This mode can run the CD sled motor freely. Use this mode, for 2. Press two buttons of x and Z simultaneously for five seconds.
instance, when cleaning the pick-up. 3. The message “LOCKED” is displayed and the tray is locked.
(Even if exiting from this mode, the tray is still locked.)
Procedure: 4. Press two buttons of x and Z simultaneously for five seconds
1. Press ?/1 button to turn the set ON. again.
2. Select the function “CD”. 5. The message “UNLOCKED” is displayed and the tray is
3. To enter the test mode, press three buttons x , unlocked.
PLAY MODE/TUNING MODE , and Z simultaneously. 6. To exit from this mode, press the ?/1 button to turn the set
4. The CD service mode is selected. OFF.
5. With the CD in stop status, press M button to move the pick-
up to outside track, or press m button to inside track.
6. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Press ?/1 button to turn the set OFF.
Note: • Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
19
HCD-RG121
[CD Repeat 5 Times Limit Release Mode]

Procedure:
1. Press ?/1 button to turn the set ON.
2. Select the function “CD”.
3. Press three buttons x , CD and ENTER simultaneously.
4. The message “LIMIT OFF” is displayed.
5. Press ?/1 button the set OFF.
[AMP TEST MODE]

Procedure:
1. Press ?/1 button to turn the set ON.
2. To enter the test mode, press the three buttons x ,
PLAY MODE/TUNING MODE and ENTER simultaneously.
3. Press the DISPLAY button.
The message “V0 0 0” “ 000” is displayed.
4. Press the GROOVE button.
The message “DBFB ON” “DBFB OFF” is displayed.
5. Press the SURROUND button.
The message “SURROUND ON” “SURROUND OFF” is
displayed.
6. Press the EQ BAND button.
The message “LOW” “MID” “HIGH” is displayed.
7. Press ?/1 button to turn the set OFF.
20
HCD-RG121
SECTION 5
• Circuit Boards Locations
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.) SENSOR board BD80A board
Note on Schematic Diagram: Note on Printed Wiring Boards:
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side. SW board
MOTOR (TB) board
50 WV or less are not indicated except for electrolytics • : Pattern from the side which enables seeing.
and tantalums. MOTOR (LD) board
• All resistors are in Ω and 1/4 W or less unless otherwise
specified. Caution:
• f : internal component. Pattern face side: Parts on the pattern face side seen from
(Side A) the pattern face are indicated. DRIVER board
• C : panel designation.
Parts face side: Parts on the parts face side seen from
Note: (Side B) the parts face are indicated.
CONNECT board
The components identified by mark 0 or dotted line with • Indication of transistor.
mark 0 are critical for safety.
Replace only with part number specified.
C
• A : B+ Line.
• B : B– Line. These are omitted. Q TRANS board
• H : adjustment for repair. B E AMP board
• Voltages and waveforms are dc with respect to ground Q
under no-signal (detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
B C E
Voltage variations may be noted due to normal produc-
tion tolerances. These are omitted.
no mark :FM
( ) :CD STOP
• Abbreviation
AR : Argentina model
AUS : Australian Model
E2 : 120 V AC Area in E model
E3 : 240 V AC Area in E model
E51 : Chilean and Peruvian model
EA : Saudi Arabia model
MX : Mexican model
SP : Singapore model VIDEO OUT board
• Waveforms are taken with a oscilloscope. SUB-TRANS board
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER
d : PB (DECK A) REM board
d : PB (DECK B)
G : REC (DECK B)
J : CD
f : AUDIO
PANEL board
MAIN board
• Waveforms 1 STREAM LED board

– PANEL BOARD –
1 IC601 qd (I-XT2)
GAME JACK board
5.2 Vp-p
30.5 s
TRANSRATION board H/P JACK board
2 V/DIV, 10 s/DIV
AEP, UK
2 IC601 qh (CF2)
4.9 Vp-p
100 ns
2 V/DIV, 40 ns/DIV
21 21
HCD-RG121
5-1. BLOCK DIAGRAM – PANEL SECTION –
IC601(1/2)
SYSTEM CONTROLLER
S641-S650 Q610
FUNCTION LED
25 KEY3 STREM-LED1 82
KEY DRIVER
S601-S608,S610-S612 LED851
FUNCTION
27 KEY1
KEY
S621-S624,S627-S630
FUNCTION
26 KEY2
KEY
S851
9 VOLUME-IN1
MASTER VOLUME ENCODER
10 VOLUME-IN2 PT901
POWER TRANSFORMER
D401 F904
IC302
+3.5V 2 REG 1 +B F905

IC610
4 -B
REMOTE
CONTROL 3 28 SIRDS-IN Q301,Q302
RECIEVER
SWITCH
POWER LED 76
IC301 D301-D304 F906
LED601
+3.5V 3 REG 1
CN603
Q902
SCOR C1 C18 80 MP3-TTB D902 AC3
C2 C15 -VFL REG
XTCN 6 MP3-RESET
XRST C3 C14 4 MP3--REQ
C4 C13 IC303 D305-D308 F907
XL-T-CD 3 MP3-ACK 42
CD-DATA C5 C12 2 MP3-CS G01-G13
30 +9V 3 REG 1
SENS C6 C11 1 MP3-CS'
CD-CLK C7 C10 100 MP3-CLK
BD/DRIVE C8 C9 FL601 IC304 D309-D312
SECTION A MP3-DO
MP3-DI C9 C8
99 MP3-DI
98 MP3-DO FLUORESCENT VF
AC4 RY901 S901 (EA,SP,E2,E3,E51)
+9V 3 REG 1
(Page 24) C10 C7 43 INDICATOR
MP3-CLK 97 CD-CLK -VFL VF VOLTAGE AC
C11 C6 45 TUBE SELECTOR IN
MP3-CS 96 SENS
C12 C5 47
MP3-CP 95 CD-DATA S1-S21
C13 C4 50
MP3-ACK 94 XLT Q361,Q362,Q314,Q315
52
MP3-REQ C14 C3 93 XRES RELAY
65
MP3-RESET C15 C2 92 XTCN DRIVE
MP3-STB C18 C1 5 SCOR
D902-905
IC603
3.3V 5 REG 1
12 XT1
X601 POWER RELAY 74
32.768kHz 13 XT2 Q605 IC604
RESET PT902
RESET 11 3 RESET 1
SWITCH SUB TRANSFORMER
15 CF1
X602 ACCUT 29
10MHz 16 CF2
22 22
HCD-RG121
5-2. BLOCK DIAGRAMS – MAIN SECTION –
IC101
SOUND PROCESSOR
CD-L IC441
BD/DRIVER 1 CDL
SECTION B CD-R
R-CH
IC102 POWER AMP JK441
BUFFER RY441
(Page 24) Q304-Q307 SWITCH
4 L
VOUT2 32 11 Q481,Q482
5 SPEAKER
VOUT1 33 R-CH OVERLOAD
CD-MUTE 13 R-CH
TUNER MUTE DET R-CH R
Q101-Q104 Q441,Q442
TUNER-L 61 TUNER_L STK MUTE Q489
OVERLOAD
TUNER-R R-CH DET Q312
DO DRIVE
DO
DI
DI
CLK Q485-Q488 SPRELAY
CLK
CE RELAY
CE
TUNED DRIVE
TUNED
STEREO
STEREO
(AEP,UK)
Q106 Q483,Q484 Q308,
RDS DATA BBNF1 34 BUFFER
RDS DATA Q309,Q313
RDS INT OVERHEAT
RDS INT BBIN1 35
DET SWITCH
DATA
TU-MUTE 19 SI BBNF2 31 TH441
RCLK AC4
18 SO BBNF2 30 Q107
BUFFER
59 GAME-L SAOUT2 55 Q351,Q352
9 TAPEA1 SAOUT1 56 SWITCH
11 TAPEB1 Q327
J804 BUFFER
VIDEO 15 REC-OUT1 ASMOUT 40
GAME INPUT L
R R-CH
IC601(2/2)
SYSTEM CONTORLLER
J803 Q308,Q309
VIDEO OUT VIDEO Q313
SWITCH STK J801

24 I-STREEMA/VACS PHONES
DECK-A 75 SYSTEM-MUTE WFR/HP/MIC 19
IC371
69 ASM PROTECT 18
HP2 L SP DRIVER
HP1 R R-CH
11 Q5 (AEP,UK)
DECK-B RDS DATA

7 I-BU1924 DATA
RDS INT
12 Q6 8 I-BU1924 CLK
HRP2 L CN201
Q324
HRP1 R R-CH +9V SENSOR 73 CD NO SENS
BD/DRIVER
L101 Q321 RCLK CD-OPEN/CLOSE 21 CD OPEN/CLOSE D SECTION
88 CLK CD ENCORDER 20 CD ENCORDER
BIAS DATA (Page 24)
7 Q1 91 DATA
HE1 OSC
LM-R
Q322,Q323 TUNED
67 TUNED
9 REC SW STEREO LM-F
CONT 4 SWITCH 6 Q0 68 STEREO
7 P/B SW
TM-R
CD-MUTE 10 Q4
IC201 TM-F
SP RELAY 17 Q11 DI
SELECTOR 83 DI
LM-R CE
13 Q7 84 CE
LM-F DO
14 Q8 DATA 3 85 DO
TAPE TM-R CLK
15 Q9 CLOCK 4 86 CLK
MECHANISM DECK TM-F LCH
16 Q10 LCH 5 87 LCH
PWDEWC B
MODE B
MODE A
B HALF 23 TAPE B START+
A HALF 22 TAPE A START+
A-PHOTO 70 I-REEL-A • R-CH is omitted due to same as L-CH
B-PHOTO 71 I-REEL-B
• Signal Path
Q601,Q606
CAP M MOTOR : TUNER
COMP 2 MOTOR
DRIVE
: CD
Q602,Q607
B TRIG SOLB : PB(DECK A)
AOLB 3 SOLB
DRIVE : PB(DECK B)
Q603,Q608
: REC(DECK B)
A TRIG SOLA
SOLA 4 SOLA
DRIVE : AUDIO
23 23
HCD-RG121
5-3. BLOCK DIAGRAMS – BD/DRIVER SECTION –
OPTICAL PICK-UP
BLOCK
(KSM-213DCP/Z-NP)
IC101
DETECTOR RF AMP
VCC +1.7V • R-CH is omitted due to same as L-CH

VC 24 VC • Signal Path
IC701
: CD (LD)MOTOR DRIVER
A 25 A CN701
B 26 B LMR 9 RIN OUT1 4
C 27 C LMF 11 FIN OUT2 2 M M751(LOADING)
D 28 D TM-R
E 18 E MAIN TM-F
F 19 F
SECTION D TBL ADDRESS SW M M741(TBL)
(Page 23)
E-1
Q10
E-2 IC712
LD LD E-3
34 LD TBL MOTOR DRIVER
DRIVER
OPEN SW
9 RIN OUT1 4
GND S751 7 FIN OUT2 2
(LEVER SW)
+3V
CN201 IC731
Q731 (TABLE SENSOR)
PD
35 PD CLOK 98 CLK RE701 SWITCH
VR DATA 95 DATA
IC251 E-3
XLAT 97 XLT
SL/SP MOTOR PANEL E-2
DRIVER SENS 100 SENS A SECTION E-1
F+ SCOR 100 SCOR (Page 22)
12 CH2OUT-F
FOCUS XRST 93 XRST
SSTP 7
COIL F ROTARY
S101 XTACN 88 XTACN
11 CH2OUT-R ENCODER
LOUT
AOUT1 76 LOUT
T+ ROUT MAIN
TRACKING
13 CH1OUT-R AOUT2 81
DOUT
ROUT B SECTION
DOUT 67 DOUT (Page 23)
COIL T
14 CH1OUT-F
CH3FIN 23 9 SFDR
CH3RIN 22 10 SRDR
14 CH1OUT-F
M101
(SPINDLE) M CH2IN 7 14 FRDR
13 CH1OUT-R
CH2FIN 6 13 FFDR
CH1RIN 5 12 TRDR
18 CH3OUT-R
M102 CHIFIN 4 11 TFDR
(SLED) M
17 CH3OUT-F
24 24
HCD-RG121
5-4. PRINTED WIRING BOARD – BD80A SECTION – • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9
SPINDLE
B MOTOR
(LIMIT)
IC251 SLED
C E MOTOR
OPTICAL
PICK-UP
BLOCK
(KSM–213DCP)
D
IC101 CONNECT
BOARD
CN872
(Page 32)
25 25
HCD-RG121
5-5. SCHEMATIC DIAGRAM – BD80A SECTION –
C14 0.1
TP46 TP45 C10 10 CN101

IOP1 IOP2 Q10 TP27 16P
2SB1690K TOP1 JR111 0 C11 10
C15
0.1
TP014 E
R13 R10 TP17 D
1 3.3
TP18 A
C16 C18 JR105 TP19 B

C17 1 R11 0.001 0
220 0 TP015 F
10V
R12 100k
TP28 LD
TP22 PD
C142
C132 0.47
C131 100p
0.0015 C133
R131 1M
C151 0.01 TP23 F+
220
10V R143 TP012 TP21
C125 AGND TP24 T+
3.3k RFACO
0.1
R133 TP25 T-
R202 C124
C143 C141 180k
0 330p JPO001 TP26 F-
0.1 0.1
R132 SHORT
R142 1k
JR109
R121 15k
C123 0.1
10k
JR108 0
0
JR106 0
R141 4.7k
R151 C117 C122
0.1 0.1 TP011
0
RFDC
TP013
VC
TP20 C
C116
220
10V
M101
C161 R111 1k R112 15k C111 0.0033
0.1
JPO002 SHORT C112
470p
R113 1k
C113
0.0033 M102
R114 15k
JPO003 SHORT C114
470p
R161 100 JR101
C258 C257
0
0.1 0.1
C259 0.1
C162 0.1 C115 JR107 IC251
0.1 0
BA5947FM
C174 C171 X101
0.1 22p 16.9344MHz IC101
CXD3058AR
R171 470
C172 R172
R173 27p 1M JPO004 SHORT
0
R181 100
C185 C183 C195 0.1 C251

C182 220
470p TP016 0.0068
0.1 10V SSTP R252
C184 22k
220 C170
C186 220
C181 470p 10V
TP010 R251 16V
0.1 LOCK 10k
C252
R182 100 TP009 S101 0.1
FOK LIMIT IN SW
TP008
DFCT
TP007
MIRR
C201
220
10V R162 C194
47k 0.1
C160
0.1
CN201 C164
17P R412 0.1
TP29 XTACN
WFCK
100 TP001
TP002
TP003
TP004
XUGF
TP005
XPCK
TP006
C2PO
GFS
JR103 JR102
EXCK
C203 0 0
220 C210
TP31 DOUT 10V 0.1 JR104 0
TP32 AVDD
TP33 LOUT R201 0
TP30 AGND
TP34 ROUT JR110 C163
0 0.1
TP35 DGND
TP36 DVDD R204 0
C211
TP37 XRST R406 100 C202 0.1 220p
C212 22p
TP38 DATA C213 22p R407 100

TP39 XLT R408 100
TP40 CLK R409 100
33
TP41 SENS R410 100
TP42 SCOR R411 100
TP44
M+7V TP43
MGND(7V)
26 26
HCD-RG121
5-6. PRINTED WIRING BOARD – CD MECHANISM SECTION –
1 2 3 4 5 6 7 8 9 10 11 12 13 14
CN704
B CN702
C751
CN705
R733
C737
Q731
R735
R734
R732
C736
C C735
JW710 R751
CN742
R723 JW711 CN741
C741
CN703
R722 C752
R721 JW712
JW709
JW708
JW707
D JW706
C715
D701
JW705
D711
R713
R702
R701
CN721
R711
IC731
E R712
JW713
MAIN
CN701
JW704 BOARD
JW714 CN301
JW703 (Page 29)
CN731
IC701
IC712
JW702
F R731
JW701 C731
G
• Semiconductor S751
Location CN751 (LEVER SW)
Ref. No. Location

D701 D-6
D711 D-7
H IC701 F-6
IC712 F-7
IC731 E-11
Q731 C-9
27 27
HCD-RG121
5-7. SCHEMATIC DIAGRAM – CD MECHANISM SECTION –
IC701
BA6956AN
LD MOTOR
DRIVER
OUT2
OUT1
VREF
GND
VCC
RNF
RIN
VM
FIN
C715 CN701
100 12P
16V
R702
100 R701
470
D701
MTZJ-T-77-5.1A
M751 IC712 CN301

(LOADING) 31
BA6956AN
C751
CN721 CN704 0.01 TBL MOTOR
2P 2P DRIVER
OUT2
OUT1
VREF
GND
VCC
RNF
RIN
VM
FIN
C752
0.1
S751
(LEVER SW)
R712 R751
4.7k R711 4.7k CN705 CN751
1k 2P 2P
R713
22k
M741 D711
(TBL) MTZJ-T-77-3.6B
R731
CN742 R732 100
5P 10k RE701
C741 ROTARY
0.01 CN703 CN751
IC731 C731 R721 R722 R723 4P 4P ENCODER
RPI-576 CN731 CN741 R734 4.7k 4.7k 4.7k
3P 3P R735 12k 10 E-3
TABLE 100 50V
SENSOR R733 E-2
1k Q731
DTC114ESA E-1
TBL ADDRES C735 C736 C737
SENS SWITCH 0.1 0.1 0.1
CN702
5P no mark : FM
28 28
HCD-RG121
5-8. PRINTED WIRING BOARD – MAIN SECTION – • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
GAMEJACK
DRIVER
BOARD
BOARD
CN801
A (Page 32)
CN701
(Page 27)
EXCEPT AEP, UK
E
TUNER
AEP, UK
IC371
B E
E
3 1 • Semiconductor
CONNECT
Location
BOARD 1 12
CN874 Ref. No. Location
(Page 32) AEP.UK
D201 I-10
D211 F-4
C EXCEPT
AEP.UK
D212 G-5
D213 G-5
10
D214 G-5
D215 G-4
PANEL D301 I-8
BOARD E D302 I-8
CN601
(Page 34) IC102 D303 I-8
D IC101 D304 I-8
C161
E E D305 I-7
E
D306 I-7
AEP, UK
AEP, UK
30
31 AEP, UK D307 I-7
DECK-A
D308 I-7
AEP,UK
(PLAY) E C227
E D309 I-7
HP1 D310 I-6
1 3
E R CH D311 I-6
PB
HEAD 2 1
E D312 I-6
1
IC302
L CH
3
D313 F-8
HP2 IC201 3 D314 F-9
9 1
9 1
D315 H-8
DECK-B
(REC/PLAY)
E E D316 G-6
33
E
D321 H-5
ERASE 1 6
D322 H-5
F REC/PB
HEAD 2
C288
AEP,UK
D324 E-4
HEAD HE1
3 1 8 D325 E-4
L CH
4 E D326 F-4
HRP2
3
R CH
4
1 3 1 3 1 3 IC101 D-6
HRP1 E IC102 D-8
E
IC304 IC303 IC301 IC201 E-5
G E
E E
IC301 G-8
E IC302 E-9
E IC303 G-7
E
IC304 G-7
E
IC371 B-4
E E
Q101 H-9
H Q102 H-9
Q103 H-9
Q104 H-10
E
1
Q105 E-11
Q106 D-7
Q107 D-7
H/P JACK 5 Q304 E-4
BOARD
AEP,UK Q305 E-4
I CN804
(Page 32) Q306 B-4
11 1
Q307 B-4
13 1
C289 Q308 B-4
AEP,UK Q309 B-3
Q312 H-10
Q313 B-3
21 Q314 G-6
J Q315 G-6
Q321 F-7
Q322 F-4
(CHASSIS) Q323 F-4
(CHASSIS) Q324 F-4
TRANS AMP
BOARD BOARD Q327 G-5
CN907 CN441 Q351 G-4
(Page 37) (Page 38)
K Q352 G-4
Q361 G-6
Q362 G-6
29 29
HCD-RG121
5-9. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) –
R385 R386
4.7k 22k
R389 R390
R387 4.7k 22k
4.7k
R388 R392 R391 R151

22k 1k 10k 4.7k
Q101
2SC1623
R394 R393
1k 10k
R152 10k
R216 R217
R219
* R218, R219
680 2W : AEP, UK
R154 R153
CN309 C235 56 56 R395 10k 10k
5P 0.1 * 680 3W : EXCEPT AEP, UK 22k
33 R218
Q102
2SA1235
*
C175
JW202 2.2 50V R155
JW201 JW R162
JW 4.7k
2.2k
EP101 R157
47k R158
2.2k
R156 Q103
Q312 470k 2SC5938
2SA953 Q104
DRIVE 2SC5938
R231
2.2k
R163 10k
R159 10k
R232 R164 R160

10k R165 1k R161 1k
10k 10k
C176 C185
10 50V 10 R172 C187
CN307 R220 R222 50V 100 0.01
13P 22k 5.6k
R174 10k
C177
C188 22p C186
22 C178
50V 47 47
R175 R173 R167 R166 R170 16V
10k 16V 10k 10k 10k
R221 D201 R223 10k C184
22k 1SS355 0 C189 47
C179 C183
22 Q105 22p 16V
50V 2SC3661 SWITCH 47p
C190 R168 C181 R171

0.01 100k 47p 6.8k
C289 IC102
0.001 NJM4565M
R169 100k
AEP, UK
39 C166 1 50V
C162 1 50V
R141 1k C165 1 50V
C290
0.001
R142 1k C164 1 50V
R139 0
R138
1k R137
0.0022
C160 1 50V
C159 10k
C154 0.47
1
50V C157 C152
1 0.0022
C153
50V
C107
10
R202 R102 50V R105
R201 10k 10k 390
4.7k
C106
R101 AEP, UK 0.01
R204 R203 10k
10k 10k C105 220p R103 C151
C161 330k 0.01
C101 1 50V 0.001 R136
R104 15k
R272 Q304 Q305 4.7k
470k 2SC3052 2SA1235 C163
0.001 C150 0.01
C211 R205
4.7k C102 1 50V C149 0.01 R135
2.2 50V 4.7k
C103 0.1 50V C148 0.01
C147
C206 R198 2.2k C104 AEP, UK R134 4.7k 10 50V
R206 R207 0.1
C214 2200p
1000 47k R210 2.2k R197 2.2k 50V C146
CN305 2.2k 0.1
10P 10V R108 390 C109 0.01 C108 220p C276
Q306 470p R133 C145
Q307 2SC5938 C277 4.7k 10 50V
C193 C110 R106 R107 470p IC101
2SC5938 10 330k 15k
2200p BD3401KS2
C213 50V C144 0.1
C216 C222 10 50V
0.1 0.1 R209 10k C111 1 50V R281 2.2k C278
470p C142 C143
C279 10 1
C217 0.1 R208 1k C112 1 50V R282 2.2k 470p 50V
C212 50V
10 50V C113 1 50V C280
R212 10k R211 1k R283 2.2k 470p
FB201 0 C281 C141
C114 1 50V R284 2.2k 470p 10 50V
FB202 0 C140
0.068
FB203 0 C139
R109 0.068
33 FB204 0 470k
R132
4.7k
C119 0.01
D324 C275
C116 220p
C120 220p
R112 470k
C115 0.01
10EDB40 47p
C138
10
50V
D325 R176
C137 R131
10EDB40 220k 15k
10
50V
C121 220p
C117 220p
C126 1000p
R110 R113
0.001
C123 22 50V
C272
AEP,
330k 330k
UK
C136 0.068
C135 0.068
D326 C274 R177 Q106
C125 100p
CN314 10EDB40 47p 220k 2SC3052
C128 100 10V

3P R129
C129 47 16V
C127 100 10V
R111 R115 R127
R195 R114 1M 4.7k 47k
150k R194
6.8k 6.8k 150k R128
C271 0.001
15k
AEP, UK
C118 C192 C191 C122 R121 R120
10 2.2 2.2 10 C124 47k 1M
JW311 50V 50V 50V 50V 100p
Q107
R119 47k
2SC3052 C132
47
R196
33 0 16V
R116 100
R117 100
(PAGE 31)
30 30
HCD-RG121
5-10. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) –
30
Q362
2SC1623 C270
10 50V
R362 R361
2.2k
10k
R364 Q361
4.7k
2SA1235
R363
4.7k
R275 0
D316
R274
0 1SS355
Q315
2SC1623
Q314
2SA1235
R323 R253
4.7k C252 100
R321 100
C312 16V
4.7k R324 10
10k 50V
R322 R262
TA78033LS
D212 C253
22k C321 3.3k
C315
IC302
2.2 1SS355 0.1 50V
100 D215
50V
16V 1SS355
C311 C258
10 0.47 D213
50V C309 50V 1SS355
C318 22 Q327
100 16V 50V
D321 2SC3052
1SS355 Q321 R264
C241 2SC2001 1k
1000p
C308
22
C259
TA78033LS
R325 50V 0.22 50V
R241
IC301
TA7809S
4.7k R263
10
IC304
JW301 1M
JW
TA7809S
D313 R242
IC303
R266 R265
JW303 11EQS04 27k
C242 C243 100k 10k
JW C244
0.0047 0.015 0.015
D314 R243
10EDB40 8.2k
D214
1SS355
C251
D315 47 16V
10EDB40
R250 R252
C313 R251 0
C310 10k
2200 10k
C316 3300
25V 16V
2200
25V Q324
D311 C302 2SB1116
JW302 JW305 L101
R273 0 10EDB40 EP301 0.1
JW JW
10EDB40
D309
D308 10EDB40
D312 D310 D307 C301
10EDB40 10EDB40 10EDB40 0.1
39 D306 D305
10EDB40 10EDB40
D301 C248 1000p
D302 10EDB40 R244 C246
C306 C303 10EDB40 8.2k 0.015
0.1 0.1 M
CN303 C305 0.1
11P
C304 0.1
D303
D304 10EDB40
C354 10EDB40
0.1
IC201
BA3126N
C351
C374 1000p
47
16V R351
R353 15k R352
47k 100k
C375 HP1
C264
0.1 1000p
C371 R245 Q351
470p 4.7k 2SC3052
R371 R356
100 470 HP2
C372 R354 C265

100p C249 4.7k
R357 1000p CN112
10 3P
R372 R384 50V 2.2k
100 10k R313
4.7k
R373 C373
100 100p Q352
D322
1SS355 2SC3052
R374
10k R383 10k R312 22k C266
1000p HRP1
C376
R375 2.2 R306
10k R382 10k 10k
50V
R376 R381 R307 Q308
10k 10k 2SA1235 R358
10k 100
C352 22 50V HRP2
R380 10k
R377
R311
R246 100 C267 1000p
4.7k
10k
R247
10k C353 C288
R378 R308 2.2
R379 2.2k 0.001
10k IC371 50V HE1
BU2099FV 10k
R248
R310 Q322 10k Q323 AEP, UK
Q313 10k 2SA1235 2SC3052
2SC3052 C250
47 CN103
16V 8P
D211 R249
1SS355 47k
Q309
2SC3052
RDS INT
RDS DATA
RDS DATA
RDS INT
R348 22k
R346 R345
R214 1k
R213 1k
1k 10k
C342 R347 R342 R341

0.1 22k 1k 10k
R343
*CN302 22k R344 22k *CN101
29P : EXCEPT AEP,UK 11P : EXCEPT AEP,UK
31P : AEP,UK CN301 15P : AEP,UK
12P
31
RDS DATA
RDS INT
N.C
+3.3V
RDS INT
RDS DATA
AEP,UK
EXCEPT AEP,UK
AEP,UK
EXCEPT AEP,UK
28
35
31 31
HCD-RG121
5-11. PRINTED WIRING BOARD – PANEL COMB SECTION – • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11
A PANEL
BOARD
CN603
1
(Page 34 ) (AMS- (AMS+
HML-) HML+)
5 MAIN
BOARD
CN309
(Page 29)
B 7
(CHASSIS)
(ILLUMINATION 6
LIGHT)
PHONES
J
MAIN PANEL
BOARD 1
BOARD
CN305 3 1
CN604
(Page 29) (Page 34)
C MASTER VOLUME
13
13
D BD80A
BOARD
CN201
(Page 25) AEP, UK
TRANSLATION BOARD
(CHASSIS)
VIDEO
E 1
1
2
OUT (CHASSIS)
2 1 E
3 MAIN
BOARD
CN314
(Page 29)
1-862-310-
(CHASSIS)
F
VIDEO L R
AUDIO
GAME INPUT
32 32
HCD-RG121
5-12. SCHEMATIC DIAGRAM – PANEL COMB SECTION –
C830 C831
1000p 1000p
S851 J801
JW275 JW865 ENCORDER
JW
VR
JW276 JW866 SW851

CN872
17P JW SW ESE24SV
CN874
9P
CN804
5P
C832
R852 30 0.1
220
1/8W
JW862 JW
JW863 JW FB871 0 R853
22k
W803
WIRE
JW864 JW 30 LED851
SELU5223C
FB872 CN873
JW876 0 7P -STP15
JW CN851
6P
26
JW861
JW
35
C872 0.01
C871 C873 36
100p
100p
CN805
2P J803
CN802
2P
AEP, UK
J804
TRANSLATION
R801
BOARD 10k
R803 C801
22k 470p
C861
0.001 JR801
0
R804 C802
22k 470p C804 C803
0.22 0.22
W806 R802
10k CN801
3P
(CHASSIS) 30
WIRE801
33 33
HCD-RG121
5-13. PRINTED WIRING BOARD – PANEL SECTION – • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
* D620 D621 D622 D623
AEP, UK
EA
A CONNECT
BOARD MX, AR, E2, E51
CN873 (CHASSIS) ES, AUS, SP
(Page 32)
1 5 10 15 20 25 30 35 41 45
E
(FLUORESCENT INDICATOR TUBE) E

B *
51 50
DISPLAY
3 1
31
DISC 1
80 IC601 30
4 3
GROOVE 5
C 81
3
1
1
IC610
100 1
DISC 2 EQ BQND
IC604
3
E
AEP, UK
AEP, UK SURROUND 1
AEP, UK CD
PLAY MODE/
DISC 3 EXCEPT AEP, UK TUNING MODE
D
EXCEPT AEP, UK
EFFECT
5 4
TUNER/BAND
ON/OFF
1 3
IC603
AEP, UK
EXCEPT
• Semiconductor
M Location
MAIN M E
BOARD TAPE A/B
CN302 ENTER
E Ref. No. Location
E (Page 29)
D603 C-11
X E D604 C-11
RESET EQ D605 C-10
E D607 C-10
h GAME MIXING
D608 D-8
DISC SKIP x GAME
EX-CHANGE
D609 D-8
D610 D-8
D611 D-8
F P FILE
TUNING+ TUNING-
D613 D-9
CD SYNC D614 C-9
D615 F-6
E
D616 F-6
E
13 D620 B-6
E 6 1
REC (13) D621 B-6
PAUSE/START
D622 B-6
D623 B-6
D624 B-6
G 1 STREAM D630 E-4
TAPE LED BOARD D631 C-8
MECHNISM CN851 D632 C-9
DECK (Page 32)
IC601 C-7
IC603 D-9
IC604 C-8
IC610 C-12
LED601 B-11
Q601 F-6
Q602 F-7
Q603 F-6
Q604 B-9
Q605 C-8
Q606 E-10
Q607 E-10
Q608 E-10
Q610 E-8
Q616 A-9
34 34
HCD-RG121
5-14. SCHEMATIC – PANEL SECTION (1/2) –
R698
220
Q610
DTC143EKA
-T146
CN604
33 6P
* CN601
29P : EXCEPT AEP,UK
31P : AEP,UK
AEP,UK AEP,UK
JW784 A18
31
BU1924 DATA
EXCEPT JW783 A17
AEP,UK
BU1924 CLK
JW601
JW602
R629 10
R628 10k 36
D605
1SS355TE-17
R627
10k
R854
220
R690 100 R639 D604

4.7k 1SS355TE-17
R691 100 C605
R641 4.7
R640 220k
50V
12k D603
1SS355TE-17
R692 100 JW603 JW
R693 100
R694 100
R695 100
R696 100
R697 100
31
C655 0.1
R674
15k
R663 R652 R651 R649 R648 R647 R646 R645

R650 R644 R643 R642
22k 15k 10k 4.7k 3.3k 2.2k 1.5k 1.5k
6.8k 1k 680 470
R635 100
S612 S611 S610 S608 S606 S605 S604 S603 S602 S601
S607
R662 R659 R658 R654 R653

R661 R660 R657 R656 R655
10k 3.3k 2.2k 680 470
6.8k 4.7k 1.5k 1.5k 1k
R675
15k
S621
S629 S624 S623 S622
S630 S628 S627
R722 R720 R671 R670 R669 R668 R665

R721 R667 R666 R664 R676
15k 6.8k 4.7k 3.3k 2.2k 1.5k 680
10k 1.5k 1k 470 15k
S645
S650 S649 S648 S647 S646 S644 S643 S641
S642
35 35
HCD-RG121
5-15. SCHEMATIC – PANEL SECTION (2/2) –
* D620 D621 D622 D623

1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17
AEP, UK
EA
MX, AR, E2, E51
FL601
FL ES, AUS, SP
C634 100p
R769 100k
R768 100k
R767 100k
R766 100k
R765 100k
R764 100k
R763 100k
R762 100k
R761 100k
R760 100k
R759 100k
R758 100k
R757 100k
R756 100k
R755 100k
R754 100k
R753 100k
R752 100k
R751 100k
R750 100k
C639 100p
C638 100p
C637 100p
C636 100p
C633 100p
C632 100p
C631 100p
C630 100p
C629 100p
C628 100p
C640 100p
C635 100p
R770 100k
C623
4.7
50V
C622
4.7
50V
CN603
7P
R710 R712
10k 10
R778 100
R719 C620
3.3k R718 47 C621 LED601
R777 100 22k 35V 0.022 SELU5223C -STP15
R716
R776 470 22k R772 1k R771 R711 R713
C642
0.1
47k 10k C617 C618 10
R775 100
1000p 1000p
R606 4.7k
R605 4.7k
R774 100
R607 47k
33 JR617 0 * * * *
R717
D623
D622
D621
D620
3.3k
1SS355TE-17
R601 4.7k
R602 4.7k
R603 4.7k
R604 47k
R796 100
D624
R794 100
R793 100
R792 100
R608
4.7k
R795 100
R621
10k
R622
1k
Q601
2SB1068TP-K
R790 R609
Q606 1k
DTC143EKA- 22k
T146 JR621 R611
0 R610
10k 22k
R797
1k
R623
R613
10k R612 22k
10k
R624
R773 100 1k
R789
47k Q602
2SB1116-TP-LK R614
C641 22k
0.1
25V Q607 R615
DTC143EKA- 22k
T146 D615
1SS355TE-17
R798
R749 100k 1k
C643 0.1
R748 100k R616 R617
R625 10k 22k
IC601 R747 100k
LC876972B 10k
-52S2-E R746 100k R626 R799
1k 1k CN602
R745 100k R618 R619 13P
10k 22k
R744 100k Q603
2SB1116-TP-LK
R743 100k R620
22k
R742 100k
Q608
R784 100 DTC143EKA-
R741 100k D616
T146
1SS355TE-17
JR613 R740 100k
0
R739 100k
R738 100k
CN608 IC610
R714 3P RPM7240-H4
100
JW638 JW JW684 JW
R630 100
JR624 0
JW685 JW
JW712
JW
R727 4.7M
R715 CN610
R788 100
R791 100
C626 0.1
R631 100
R737 100k
R733 100
47 3P
R729 100
R730 100
C619
R734 1k
R736 1k
R735 1k
35 47
R728 4.7M
JW620 10V
JW
JW636 JW
R725 100
JW631
A17
A18
JW
AEP, UK
R732
JW640 470k
JW X602
10MHz C607 R681
1000p 220k
C625 22p
JR605 JR
C653
32.768KHz
JR606 C649
330p
X601
C624 R680
JR612 0
JR611 0
D607 JR604 JR 0.1

AEP, UK
EXCEPT
1SS355TE-17 JR 18p 27k
C610 C611
C647
47 1000 0.1
C654 D611 D609 6.3V
10V 0.1 1SS355TE-17 1SS355TE-17
D608 R682
1SS355TE-17 10k
Q605
D630 R677 R678 2SC3052F
1SS355TE-17 0 100k IC603
MM1574A
C648 R863 R686 D633
22 68 47k 1SS355TE-17
16V R687
C612 10k
10
C608 16V C613 R685 C614
R679 C646 C609 0.1 47k 0.1
82 C606 0.01
22 1 1
16V
C656 100P
D606 Q604
PTZ-TE25 2SA1175TP-HFE
EXCEPT R689 D613 D614
AEP, UK 4.7k 1SS355TE-17 1SS355TE-17
R683 R684 D632

R786 220k 1k UDZSTE
10k R688 IC604 -173.6B
D610 470 M62703ML
UDZSTE
Q616 -174.3B C615
DTC143EKA-T146 D631 2.2
UDZSTE 50V
-174.3B
WIRE806
WIRE
(CHASSIS)
36 36
HCD-RG121
5-16. PRINTED WIRING BOARD – TRANS SECTION – • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12
1 3
SP, E2, E3, E51, EA
B 3 1
4 3 2 1
AEP, UK, MX, AR, AUS
C
POWER TRANSFORMER JW913
POWER TRANSFORMER
(MAIN)
(SUB)
AEP, UK, AR, AUS

E2, E3, SP, EA, E51, MX
1
N
AEP, UK, AR, AUS
3 AMP
BOARD
D CN442
(Page 38)
AC
IN JW914
MX
1
AUS, AR
1
AEP, UK
E
F
E51, SP, E2,

E3, EA, MX
MAIN
SP, E2, E3, E51, EA BOARD
* CN303
(Page 29)
10
S901
VOLTAGE
F SELECTOR 1 2 3 4
* Not replaceable
built in transformer
120V
220V AEP, UK, MX, AR, AUS
230 - 240V
SP, E2, E3, E51, EA
• Semiconductor
Location
Ref. No. Location
D901 B-3
D902 B-2
D903 B-2
D904 B-2
D905 B-2
D906 C-10
D908 C-8
Q902 C-9
37 37
HCD-RG121
5-17. PRINTED WIRING BOARD – AMP SECTION – • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10
A SPEAKER
(IMPEDANCE USE 6–16 )
R L
+ - + -
B AEP,UK
EXCEPT
AEP, UK
EXCEPT
AEP, UK IC441
(CHASSIS)
C E E
AEP, UK
D 1
C491
EXCEPT AEP, UK
E
E E
MAIN
BOARD
CN307
(Page 29)
E (CHASSIS)
13
• Semiconductor
Location
Ref. No. Location
D401 F-3
D441 D-6
D442 D-6
F D443 D-2
D481 D-6
3 1 D482 D-4
D483 C-9
IC441 B-7
Q441 D-6
Q442 D-6
Q481 D-9
Q482 D-8
G TRANS
BOARD
(CHASSIS) Q483
Q484
D-8
D-8
CN905 Q485 C-4
(Page 37) Q486 C-4
Q487 C-4
Q488 C-5
Q489 C-9
38 38
HCD-RG121
5-18. SCHEMATIC DIAGRAM – AMP POWER SECTION –
PT901
F904
T6.3AL/250V
CN905 AUS, AR
3P JW907
FH908 FH907 JW
240 AEP, UK
JW908 AEP, UK, MX, AR, AUS SP, E2, E3, E51, EA
JW
FH910 F905 FH909 220 CN904 CN903 * CN904, CN903
T6.3AL/250V SP, E2, JW912 * * 2P : AEP, UK, MX. AR, AUS
4P : SP, E2, E3, E51, EA
JW910 JW901
E3, E51, JW JW JW
EA
FH912 F906 FH911 2P
T3.15AL/250V 120 JW909 JW902
JW 240V JW
D901 1SS133T-77
220V
SP, E2, S901 120V
E3, E51,
EA, MX
4P VOLTAGE ↑
220V
SELECTOR ↓
FH914 F907 FH913 RY901
230 - 240V
T3.15AL/250V JW925 RELAY U
JW
R908 D908
1 1/4W 10EDB40-TB3
31 AEP, UK,
JW917 PT902
JW AR, AUS
CN907
10P
JW903
JW
Q902
2SA1932 C908 MX
220
EA, E51, MX
C906
E2, E3, SP,

63V D903 D902
0.1 JW904
10EDB40-TB3 10EDB40-TB3 JW
W001
JW905 CN901 AC CORD U
C910 R903
12k JW 2P
100
C923 0.01
R904
C920 0.01
C921 0.01
C922 0.01
C926 0.1 D904

C925 0.1
C924 0.1
MTZJ-T72-27D
50V 1k D905 10EDB40-TB3
C911 10EDB40-TB3
D906
1000
C909 25V CN902 JW906
10 CN906 3P JW
50V 3P AEP, UK, AR, AUS
TH441
TH-10K
R411 C441
2.2k 10 R441 JW403
1/4W 50V 1k JW
L441
R451 RY441
JW441 0.22 SP RELAY
5W 12V R461 10 1/2W
JW
IC441(1/2)
C445 STK403-090
R413 100p
6.8k 50V
1/4W
R483 R462 10 1/2W R463 10
EP491 22
TERMINAL, 1/4W R464 10 C455 0.1
R466 R465
EARTH 56k 47k L442 C457 0.1
EXCEPT AEP, UK C451 JK441
0.1 1/4W 1/4W R485 C456 0.1
R484 100k
56k D443 AEP,UK C459
R447 1/4W C458 0.1
33k 1/4W 1SS133T-77 0.1
1/4W
Q482 AEP,UK
2SC2785
C453
R445 R455 0.1
R491 R467 1k
1k 33k
22k AEP,UK C460
16V
1/4W
16V
R443 1/4W R486 0.1
C443 Q483
1000p 33k Q484 100k
1/4W R492 2SC2785 2SC2785 1/4W
C407 0.01
C408 0.01
D483 1k R457
C492 C447 1SS133T-77 1/4W 22k R453 C481 Q481 R407
0.01 22 10 100 2SC2785 100 EP401
35V 1/2W 10V 1/2W TERMINAL, EARTH
R493
33k Q441
Q489
1SS133T-77
1/4W 2SC1841 EXCEPT

2SC1841
D481
AEP,UK
1SS133T-77
R459 AEP, UK
D441
47k C411 C402

C488 R494
C491 22 0.01 0.01
2.2k 16V 16V
1000P 35V 1/4W
JW401
C448
1SS133T-77
JW
22
D442
R414 C444 R444 35V R495

6.8k 1000p 33k 1
1/4W 1/4W 1/4W R454 Q485
10 2SA1175
FR
R446 C489 R458 1/2W
1k 100 R460 R482 C486
22k
100V 47k 10k 2.2
R481 1/4W 50V
4.7k
1/4W
C454 CN441
R448 0.1 13P
33k R487
1/4W 33k
1/4W
C452
Q442 0.1 R490 D401
R456
C446 2SC1841 Q487 4.7k D10XB20

1k
100p 2SC2785 1/4W
2SC2785TP-FEK
50V
IC441(2/2) Q488 C403
C442 JW442 Q486 C405
STK403-090
1SS133T-77
10 R442 JW R452 2SC2785 2200 R401 0.1

1k 100k 100V
D482
50V 0.22 50V

5W C487
4.7
50V
JW402
R488 C406 R402
JW
JW404 22k R489 2200 100k
R412 JW 1/4W 4.7k 50V
2.2k 1/4W
1/4W
JW407
JW
30
R496 C404
100 1/4W FR 0.1
100V
EP402
TERMINAL, EARTH
CN442
3P
39 39
HCD-RG121
• IC BLOCK DIAGRAMS IC701, 712 BA6956AN (DRIVER BOARD)
IC201 BA3126N (MAIN BOARD)
TSD
CONTROL LOGIC
1 2 3 4 5 6 7 8 9
VREF
OUT2
RNF
OUT1
VM
VCC
FIN
GND
RIN
1 2 3 4 5 6 7 8 9
CONT
VCC
REC SW1
PB SW1
REC SW2
PB SW2
GND
GND
GND
IC101 BD3401KS2 (MAIN BOARD)
IC251 BA5947FM (BD80A BOARD)
TONE OUT2
TONE OUT1
VOLOUT1
AMS OUT
MOUT2
MOUT1
BOUT1
BOUT2
BBNF1
BBIN1
MNF2
MNF1
BNF1
BNF2
VIN2
VIN1
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
CH4OUTR 19 D D 18 CH1PUTF
LEVEL +
TNF2 49 32 VOLOUT2
+
BASS MIDDLE TREBLE
-
SHIFT -
CH4OUTF 20 D D 17 CH1OUTR
+
TNF1 50 - 31 BBNF2
CH3OUTF 21 D D 16 CH2OUTF
19k
PIN26 + +
CH3OUTR 22 D 6.5k D 15 CH2OUTR SUR1 51 30 BBIN2
BASS MIDDLE TREBLE +
10k
POW Vref POW SURROUND -
POWVCC 23 VCC VCC 14 POWVCC
(ch3, 4) (ch1, 2) SUR2 52 29 LF1
50k 50k
50k 50k ATT ATT G fc=100HZ
MUTE 24 POW 13 CNF4
VCC +
50k 50k LINEOUT2 53 28 LF2
- f
GND 25 12 GND +
0
Vref
MUTE
+
GND 26 11 C-M LINEOUT1 54 27 LF3
-
BUFFER
+
-
MIX
PREGND 27 10 C-P MIC MIX
SAOUT2 55 26 LF4
VOCAL FADER
Di-LIMITER
CT 28 R F F R 9 VG
+
R R SAOUT1 56 -
25 SWOUT
CH3RIN 29 8 CH2RIN
INTER INTER
+
SWITCH
F FACE FACE F
SOFT
CH3FIN 30 7 CH2FIN CAP 57 + 24 FILTER
F R -
100k
CH4IN 31 6 CH1RIN -
INTER MIC 58 + 23 1/2 Vcc
PIN3 FACE
CH4CAPA 32 5 CH1FIN
10k F -
GAME L 59 22 Vcc
50k +
OUTVREF 33 SW 4 SW
-
GAME R 60 21 GND
DPOUT 34 3 OPIN+ +
+
-
-
TREVCC 35 Pre 2 OPIN- TUNER L 61 20 VDD
Vcc
NC 36 1 NC INPUT
TUNER R 62 SELECTOR 19 SI
CONTROL
DIGITAL
MD L 63 18 SC
+
ALC ALC
-
MD R 64 17 ALC
+
+
+
-
-
-
-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PBOUT1
PBNF1
TAPE B1
CD R
RECNF2
CD L
PBNF2
PBOUT2
TAPE A1
TAPE B2
TAPE R
RECOUT2
RECNF1
TAPE A2
TAPE L
RECOUT1
40 40
HCD-RG121
IC371 BU2099FV (MAIN BOARD)
V DD
Q11
Q10
Q5
SO
OE
Q8
Q7
Q6
Q9
20 19 18 17 16 15 14 13 12 11
12BIT SHIFT REGESTER
CONTOROL
CIRCUIT
12BIT STORAGE
RAGESTER
OUTPUT BUFFER (Open Drain)
L. P. F
1 2
N.C. 3 4 5 6 7 8 9 10
Q1
LCK
CLOCK
DATA
Q2
Q3
Q4
V SS
Q0
41
HCD-RG121
5-19. IC PIN FUNCTION DESCRIPTION

• IC101 CXD3058AR (RF AMP) (BD80A BOARD)
Pin No. Pin Name I/O Description

1 MIRR I/O Mirror signal input/output (Not used)
2 DFCT I/O Defect signal input/output (Not used)
3 FOK I/O Focus OK signal input/output (Not used)
4 VSS – Internal digital ground
GFS is sampled at 460Hz; when GFS is high , this pin outputs a high signal If
5 LOCK I/O
GFS is low eight consecutive
6 MDP O Spindle motor servo control output
7 SSTP I Disk innermost detection signal input
8 IOVSS1 – I/O digital ground
9 SFDR O Sled drive output
10 SRDR O Sled drive output
11 TFDR O Tracking drive output
12 TRDR O Tracking drive output
13 FFDR O Focus drive output
14 FRDR O Focus drive output
15 IOVDD1 – I/O digital power supply
16 AVDD0 – Analog power supply
17 AVSS0 – Analog ground
18 E I E signal input
19 F I F signal input
20 TEI I Tracking error signal input to DSSP block
21 TEO O Tracking error signal output from RF amplifier block
22 FEI I Focus error signal input to DSSP block
23 FEO O Focus error signal output from RF amplifier block
24 VC I/O Center voltage output from RF amplifier block
25 A I A signal input
26 B I B signal input
27 C I C signal input
28 D I D signal input
30 RFDCO O RFDC signal output (Not used)
31 PDSENS I Reference voltage pin for PD
32 AC_SUM O RFAC summing amplifier output
33 EQ_IN I Equalizer circuit input
34 LD O APC amplifier output
35 PD I APC amplifier input
36 RFC I Equalizer cut-off frequency adjustment pin
38 RFACO O RFAC signal output
39 RFACI I RFAC signal input or EFM signal input
41 BIAS I Asymmetry circuit constant current input
42 ASYI I Asymmetry comparator voltage input
43 ASYO O EFM full-swing output (Low = VSS, High = VDD)
44 VPCO O Wide-band EFM PLL charge pump output
45 VCTL I Wide-band EFM PLL VCO2 control voltage input
42
HCD-RG121

47 CLTV I Multiplier VCO1 control voltage input
48 FILO O Master PLL (slave = digital PLL) filter output
49 FILI I Master PLL filter input
50 PCO O Master PLL charge pump output
52 DDVROUT O DC/DC converter output
53 DDVRSEN I DC/DC converter output voltage monitor pin
55 DDCR I DC/DC converter reset pin
56 BCKI I D/A interface bit clock input
57 PCMDI I D/A interface serial data input (2’s COMP, MSB first)
58 LRCKl I D/A interface LR clock input
59 LRCK O D/A interface LR clock output f = Fs
61 PCMD O D/A interface serial data output (2’s COMP, MSB first)
62 BCK O D/A interface bit clock output
63 VDD – Internal digital power supply
64 EMPH O High when the playback disc has emphasis, low it has not
65 EMPHI I High when de-emphasis is ON, low when input OFF
67 DOUT O Digital Out output
68 TEST I Test pin Normally ground
69 TES1 I Test pin Normally ground
70 IOVss2 – I/O digital ground
71 XVSS – Master clock ground
72 XTAO O Crystal oscillation circuit output
73 XTAI I Crystal oscillation circuit input
74 XVDD – Master clock power supply
76 AOUT1 O Lch analog output
77 VREFL O Lch reference voltage
80 VREFR O Rch reference voltage
81 AOUT2 O Rch analog output
84 RMUT O Rch “0” detection flag (Not used)
85 LMUT O Lch “0” detection flag (Not used)
86 XTSL I Crystal selection input (Not used)
87 IOVSS0 – I/O digital ground
88 XTACN I Oscillation circuit control Self-oscillation when high, oscillation stop when low
89 SQSO O Subcode Q 80-bit and PCM peak and level data output, CD TEXT data output
90 SQCK I SQSO readout clock input
91 SBSO O Subcode P to W serial output
92 EXCK I SBSO readout clock input
93 XRST I System reset Reset when low
94 SYSM I Mute input Muted when high
95 D ATA I Serial data input from CPU
43
HCD-RG121

97 XLAT I Latch input from CPU The serial data is latched at the falling edge
98 CLOCK I Serial data transfer clock input from CPU
100 SENS O SENS output to CPU
101 SCLK I SENS serial data readout clock input
102 ATSK I/O Anti-shock input/output
103 WFCK O WFCK output (Not used)
104 XUGF O XUGF output (Not used)
105 XPCK O XPCK output (Not used)
106 GFS O GFS output (Not used)
107 C2PO O C2PO output (Not used)
108 SCOR O High output when the subcode sync, S0 or S1, is detected
110 C4M O 4 2336MHz output (Not used)
111 WDCK O Word clock output f = 2Fs (Not used)
112 COUT I/O Track number count signal input/output (Not used)
44
HCD-RG121
• IC601 LC876972B-52S2-E (SYSTEM CONTROLLER) (PANEL BOARD)

1 O-MP3 CS O CS output to CD Digital Processor(Not used)
2 O-MP3 LP MOTER O Motor signal output
3 I-MP3 ACK SOL-B I Motor signal input
4 O-MP3 REQ SOL-A O Motor signal output
5 I-SCOR I CD Scor input
6 O-MP3 RESET O RESET output to CD Digital Processor
7 I-BU1924 DATA I Data input(Not used)
8 I-BU1924 CLK I Clock input(Not used)
9 I-VOLUME-IN1 I Volume signal input from the encoder
10 I-VOLUME-IN2 I Volume signal input from the encoder
11 RESET I Reset input
12 I-XT1 I Connection for input a crystal resonator
13 I-XT2 O Connection for input a crystal resonator
14 VSS1 – Ground
15 CF1 I Connection for input a ceramic resonator
16 CF2 O Connection for input a ceramic resonator
17 VDD1 – Power supply
18 I-PROTECT I Power amplifier circuit protection signal input
19 WFR/HP/MIC-IN I SubWoofer or Headphone detection signal input
20 I-CD ENCODER I Signal input from the CD encoder
21 I-CD OPEN/CLOSE I CD tray open switch signal input
22 I-TAPE A START I TAPE A switches signal input
23 I-TAPE B START I TAPE B switches signal input
24 I-STREAM/VACS I Stream/Vacs signal input
25 I-KEY 3 I Function key input
28 I-SIRDS-IN I Data input from the remote contorol receiver
29 I-AC CUT I Power down signal input
30 G13 O FL tube grid signal output
43 S1 O FL tube segment signal output
45
HCD-RG121

50 S7/METER-SW1 O FL tube segment signal output
51 -VPP – Power supply (-)
54 S10/SW1 O FL tube segment signal output
66 I-SPEC/MODE/METER I METER swich input
67 I-TUNED-IN I Tuning a frequency signal input
68 I-STEREO-IN I Stereo tuning signal input
69 I-ASM-IN I ASM signal input
70 I-REEL-A-IN I A deck photo sensor signal input
71 I-REEL-B-IN I B deck photo sensor signal input
73 I-CD Num Senser O Table address sensor swich signal input
74 O-POWER-RELAY O POWER RELAY control output
75 O-SYSTEM-MUTE O System muting signal output
76 O-POWER-LED O POWER LED control signal output
77 STREAM-LED6 SOLB O Illumination LED control signal output (Not used)
78 STREAM-LED5 SOLA O Illumination LED control signal output (Not used)
79 STREAM-LED4 MOTOR O Illumination LED control signal output (Not used)
80 STREAM-LED3 MP3-STB O Illumination LED control signal output (Not used)
81 STREAM-LED2 O Illumination LED control signal output (Not used)
82 STREAM-LED1 O Illumination LED control signal output (Not used)
83 I-LC72121 DI I Data input from Tuner
84 O-LC72121 CE O Chip select output to Tuner
85 O-LC72121/BU2099FV DO O Data input from Tuner and SP Driver
86 O-LC72121/BU2099FV CLK O Clock output to Tuner and SP Driver
87 O-BU2099FV LCH O LCH output to SP Driver
88 O-BD3401 CLK O Clock output to Sound Processor
89 VSS2 – Ground
91 O-BD3401 DATA O Data output toSound Processor
92 O-XTCN O CD xtcn signal output
93 O-XRES(RESET) O CD reset signal output
94 O-XLT(CD-LAT) O CD xlt signal output
95 O-CD-DATA O CD data output
96 I-SENS I CD sens input
97 O-CD-CLK O CD clk output
98 O-MP3-DO O Clock output to CD Digital Processor (Not used)
46
HCD-RG121

99 I-MP3-DI I Data input from CD Digital Processor(Not used)
100 O-MP3-CLK O Clock output to CD Digital Processor(Not used)
47
HCD-RG121
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • Abbreviation Note:
have some differences from the original one. AR: Argentina model The components identified by mark 0 or
• Items marked “*” are not stocked since they AUS: Australian Model dotted line with mark 0 are critical for
are seldom required for routine service. Some E2: 120 V AC Area in E model safety.
delay should be anticipated when ordering these E3: 240 V AC Area in E model Replace only with part number specified.
items. E51: Chilean and Peruvian model
• The mechanical parts with no reference num- EA: Saudi Arabia model
ber in the exploded views are not supplied. MX: Mexican model
SP: Singapore model
6-1. MAIN SECTION
#1
not
supplied
5 b
b
#1
#1
1 #1
not #1
supplied
not
3 supplied #1
1 4 #1
#1
#1 PT902 #1
2 8
a not
supplied
#1 10
CD mechanism deck section-1 not
supplied
9
#2 #1
#1 a
not
supplied 1
front panel #1
section
Main board section #2
not
supplied 12
1
#2
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 3-363-099-32 SCREW (CASE 3 TP2) 10 1-400-285-11 F-BEAD, E2515 MRT
2 4-245-183-91 CASE (SIDE-L) 12 4-245-184-91 CASE (SIDE-R)
3 4-252-196-51 DOOR, CD
4 3-038-018-01 EMBLEM, SONY 0 PT902 X-4956-322-1 SUB TRANS ASSY (EA, MX)
5 4-244-849-91 CASE (TOP) 0 PT902 X-4956-293-1 SUB TRANS ASSY (AEP, UK)
0 PT902 X-4956-294-1 TRANS ASSY, SUB (SP, E2, E3, E51, AR, AUS)
8 1-769-940-11 WIRE (FLAT TYPE) (11 CORE) (UK) #1 7-685-647-79 SCREW +BVTP3X10 TYPE2 IT-3
9 1-693-615-11 TUNER (FM/AM) (EXCEPT AEP, UK) #2 7-685-646-79 SCREW +BVTP3X8 TYPE2 IT-3
9 1-693-616-11 TUNER (FM/AM) (AEP, UK)
48
HCD-RG121
6-2. FRONT PANEL SECTION
54
61 74
60 62
65
58
not supplied 63
not supplied 73
64
57 59
66
54
67
not 54
supplied
not supplied
71
56
70 not supplied
a not supplied
59
55
not supplied
72
68 not supplied not supplied
not supplied
53
54 53
not supplied
not supplied
54
52
69 not supplied
not supplied
51
a
not supplied
51 4-252-202-01 DOOR (B), CASS 65 1-769-883-11 WIRE (FLAT TYPE) (7 CORE)
52 4-252-201-01 DOOR (A), CASS 66 4-231-841-01 SPRING (HEART CAM-B)
53 4-238-631-01 TAPE SPRING 67 4-231-825-01 CAM (B), HEART
54 4-951-620-01 SCREW (2.6X8), +BVTP 68 4-225-252-01 CUSHION (FOOT)
55 4-252-207-01 BUTTON, FF 69 1-796-485-51 DECK, MECHANICAL (CWM43FF-05)
56 4-252-208-01 BUTTON, FR 70 4-252-200-01 BUTTON COVER

57 4-252-214-01 KNOB, VOLUME 71 4-252-206-01 BUTTON, STOP
58 X-4956-295-1 RING ASSY, KNOB 72 4-252-205-01 BUTTON, PLAY
59 4-224-104-41 DAMPER 73 1-773-317-11 WIRE (FLAT TYPE) (31 CORE) (AEP, UK)
60 4-252-198-01 WINDOW, DISPLAY (UK) 74 A-4751-560-A PANEL BOARD, COMPLETE (AEP, UK)
60 4-252-198-11 WINDOW, DISPLAY (AEP, UK) 74 A-4751-568-A PANEL BOARD, COMPLETE (MX, AR, E2, E51)
61 4-231-824-01 CAM (A), HEART 74 A-4751-576-A PANEL BOARD, COMPLETE (SP, E3, AUS)
62 4-231-836-01 SPRING (HEART CAM-A) 74 A-4752-234-A PANEL BOARD, COMPLETE (EA)
63 4-252-195-41 PANEL, FRONT
64 1-769-975-11 WIRE (FLAT TYPE) (13 CORE)
49
HCD-RG121
6-3. MAIN BOARD SECTION
107
#3
#4
108
not supplied
102
101
101
107 103
PT901 not supplied
109 104
105
106
F904 F906
F905 F907
not supplied
#2
101 4-242-527-01 S-SCREW, ITC+4-8 R 108 3-905-609-41 SCREW (TRANSISTOR) (EXCEPT MX)
102 A-4751-562-A AMP BOARD, COMPLETE (AEP, UK) 109 A-4750-786-A TRANS BOARD, COMPLETE (AEP, UK)
102 A-4751-572-A AMP BOARD, COMPLETE (SP, E2, E3, E51)
102 A-4752-239-A AMP BOARD, COMPLETE (EA) 109 A-4751-570-A TRANS BOARD, COMPLETE (SP, E2, E3, E51)
102 A-4752-245-A AMP BOARD, COMPLETE (AR, AUS) 109 A-4752-237-A TRANS BOARD, COMPLETE (EA)
109 A-4752-243-A TRANS BOARD, COMPLETE (AR, AUS)
102 A-4752-256-A AMP BOARD, COMPLETE (MX) 109 A-4752-254-A TRANS BOARD, COMPLETE (MX)
0 103 1-696-570-11 CORD, POWER (EA) 0 PT901 1-443-235-11 TRANSFORMER, POWER (AEP, UK)
0 103 1-696-848-12 CORD, POWER (AUS)
0 103 1-777-071-83 CORD, POWER (AEP, UK, SP, E51) 0 PT901 1-443-238-11 TRANSFORMER, POWER
0 103 1-783-941-22 CORD, POWER (AR) (SP, AR, E2, E3, E51, AUS)
0 PT901 1-443-280-11 TRANSFORMER, POWER (EA)
0 103 1-827-226-11 CORD, POWER (MX, E2, E3) 0 PT901 1-443-283-11 TRANSFORMER, POWER (MX)
104 3-703-244-00 BUSHING (2104), CORD (E2, E3) 0 F904 1-533-473-12 FUSE, GLASS TUBE (DIA. 5) (T6.3AL/250V)
* 104 3-703-571-12 BUSHING (S) (4516), CORD (MX, E2, E3) 0 F905 1-533-473-12 FUSE, GLASS TUBE (DIA. 5) (T6.3AL/250V)
105 4-988-533-01 HOLDER, PWB
106 A-4750-781-A MAIN BOARD, COMPLETE (AEP, UK) 0 F906 1-533-470-12 FUSE, GLASS TUBE (DIA. 5) (T3.15AL/250V)
0 F907 1-533-470-12 FUSE, GLASS TUBE (DIA. 5) (T3.15AL/250V)
106 A-4751-789-A MAIN BOARD, COMPLETE (EXCEPT AEP, UK) #2 7-685-646-79 SCREW +BVTP3X8 TYPE2 IT-3
107 4-242-539-01 BVIT3B+3-8R W/O SLOT #3 7-685-872-09 SCREW +BVTT3X8 (S)
108 3-905-609-31 SCREW (TRANSISTOR) (MX) #4 7-685-649-79 SCREW +BVTP3X14 TYPE2 IT-3
The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
50
HCD-RG121
6-4. CD MECHANISM DECK SECTION-1 (CDM74-K6BD80)
156
162
158 151
157 156 163

159
158
156 164
157 161 164
155 160 165
155
M741
152
154
153
166
CD mechanism deck section-2
151
151 4-218-253-21 SCREW (M2.6), +BTTP 160 4-243-820-01 GEAR (TABLE)
153 1-687-134-12 MOTOR (TB) BOARD 161 4-243-819-01 GEAR (GENEVA)
154 4-243-815-01 TABLE (LOADING) 162 4-243-816-01 TRAY
155 4-245-571-02 GEAR (STOPPER) 163 4-243-823-01 BELT (TABLE)
164 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING
156 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING 165 4-243-821-01 PULLEY (TABLE)
157 4-245-570-01 GEAR (JOINT)
158 4-245-572-01 BUSHING (GEAR) 166 3-231-598-01 SHEET (BA)
159 1-687-132-12 SENSOR BOARD M741 A-4723-963-A MOTOR ASSY, TABLE
51
HCD-RG121
6-5. CD MECHANISM DECK SECTION-2 (CDM74-K6BD80)
205
212 213 205
216
214 217
211 205
210 215
219
231
220
RE701
202
208 205
222 205
229 223
222 222
M751 230
223
207 223
222
224
203 223 225 205
218
206
202 201 225 224
205
202 226
228
227
not supplied
204
not supplied
233
232 232
201 1-687-135-12 DRIVER BOARD 219 4-231-189-01 PULLEY (B), CHUCKING
202 4-218-253-31 SCREW (M2.6), +BTTP 220 X-4955-536-1 HOLDER (213) ASSY
203 1-687-669-12 SW BOARD 222 4-227-549-11 INSULATOR
204 4-244-034-01 BELT (LOADING)
205 4-218-252-61 SCREW (+PTPWR M2.6), FLOATING 223 4-227-045-31 SPRING (INSULATOR), COIL
224 4-231-151-01 STOPPER (BU)
206 4-225-844-01 GEAR (LOADING A) 225 4-218-253-31 SCREW (M2.6), +BTTP
207 4-224-613-01 GEAR (SHAFT) 226 1-827-991-11 WIRE (FLAT TYPE) (16 CORE)
208 1-687-133-12 MOTOR (LD) BOARD 227 1-773-050-11 WIRE (FLAT TYPE) (17 CORE)
210 4-244-108-01 GEAR, SWING
211 4-224-609-01 GEAR (LOADING C) 0 229 8-820-116-02 OPTICAL PICK-UP KSM-213DCP/Z-NP
228 A-4750-181-A BD80A BOARD, COMPLETE
212 4-224-608-01 COLLAR, SWING 230 1-471-035-11 MAGNET ASSY
213 3-016-533-11 WASHER (FR), STOPPER 231 4-243-817-01 CHASSIS
214 4-224-611-01 GEAR (LOADING B) 232 4-951-620-01 SCREW (2.6X8), +BVTP
215 4-224-606-01 GEAR (RV)
216 4-243-818-01 GEAR (U/D) 233 1-469-854-11 CORE, FERRITE
M751 A-4736-655-A MOTOR ASSY, LOADING
217 4-243-822-02 LEVER (LIFTER) RE701 1-477-680-12 ENCODER, ROTARY
218 X-4955-707-2 PULLEY (A5) ASSY, CHUCKING

52
HCD-RG121
SECTION 7
ELECTRICAL PARTS LIST 1 STREAM LED AMP
Note: When indicating parts by reference num-
• Due to standardization, replacements in the • COILS ber, please include the board name.
parts list may be different from the parts uH : µH
specified in the diagrams or the components • RESISTORS The components identified by mark 0 or
used on the set. All resistors are in ohms dotted line with mark 0 are critical for
• -XX, -X mean standardized parts, so they may METAL: Metal-film resistor safety.
have some difference from the original one. METAL OXIDE: Metal Oxide-film resistor Replace only with part number specified.
• Items marked “*” are not stocked since they F : nonflammable
are seldom required for routine service. Some • SEMICONDUCTORS • Abbreviation
delay should be anticipated when ordering these In each case, u: µ, for example: AR: Argentina model
items. uA...: µA..., uPA...: µP A..., uPB...: µPB ..., AUS: Australian Model
• CAPACITORS uPC...: µPC..., uPD...: µPD... E2: 120 V AC Area in E model
uF : µF E3: 240 V AC Area in E model
E51: Chilean and Peruvian model
EA: Saudi Arabia model
MX: Mexican model
SP: Singapore model
1 STREAM LED BOARD C446 1-162-282-31 CERAMIC 100PF 10% 50V
****************** C447 1-126-965-11 ELECT 22uF 20% 50V
C448 1-126-965-11 ELECT 22uF 20% 50V
< LED > C451 1-136-497-81 FILM 0.1uF 5% 50V
C452 1-136-497-81 FILM 0.1uF 5% 50V
LED851 6-500-809-01 DIODE SELU5223C-STP15
(ILLUMNATION LIGHT) C453 1-136-497-81 FILM 0.1uF 5% 50V
C454 1-136-497-81 FILM 0.1uF 5% 50V
< RESISTOR > C455 1-136-497-81 FILM 0.1uF 5% 50V
(AEP, UK)
R852 1-216-182-00 RES-CHIP 220 5% 1/8W C456 1-136-497-81 FILM 0.1uF 5% 50V
R853 1-216-837-11 METAL CHIP 22K 5% 1/10W (AEP, UK)
C457 1-136-497-81 FILM 0.1uF 5% 50V
< SWITCH > (AEP, UK)
S851 1-418-632-11 ENCODER, ROTARY (MASTER VOLUME) C458 1-136-497-81 FILM 0.1uF 5% 50V
(AEP, UK)
< SWITCH > C459 1-162-294-31 CERAMIC 0.001uF 10% 50V
(AEP, UK)
SW851 1-786-289-11 SWITCH, DETECTION C460 1-162-294-31 CERAMIC 0.001uF 10% 50V
************************************************************ (AEP, UK)
C481 1-104-658-91 ELECT 100uF 20% 10V
A-4751-562-A AMP BOARD, COMPLETE (AEP, UK) C486 1-126-961-11 ELECT 2.2uF 20% 50V
A-4751-572-A AMP BOARD, COMPLETE (SP, E2, E3, E51)
A-4752-239-A AMP BOARD, COMPLETE (EA) C487 1-126-963-11 ELECT 4.7uF 20% 50V
A-4752-245-A AMP BOARD, COMPLETE (AR, AUS) C488 1-126-965-11 ELECT 22uF 20% 50V
A-4752-256-A AMP BOARD, COMPLETE (MX) C489 1-128-563-11 ELECT 100uF 20% 100V
******************** C491 1-162-294-31 CERAMIC 0.001uF 10% 50V
(AEP, UK)
< CAPACITOR > C492 1-162-306-11 CERAMIC 0.01uF 20% 16V
(EXCEPT AEP, UK)
C402 1-162-306-11 CERAMIC 0.01uF 20% 16V
C403 1-137-749-11 MYLAR 0.1uF 100V < CONNECTOR >
C404 1-137-749-11 MYLAR 0.1uF 100V
C405 1-135-832-11 ELECT 2200uF 20% 50V CN441 1-778-981-21 CONNECTOR, BOARD TO BOARD 13P
(AEP, UK)
C405 1-137-839-11 ELECT 2200uF 20% 50V < DIODE >
(EXCEPT AEP, UK)
D401 6-500-360-01 DIODE D10XB20
C406 1-135-832-11 ELECT 2200uF 20% 50V D441 8-719-991-33 DIODE 1SS133T-77
(AEP, UK) D442 8-719-991-33 DIODE 1SS133T-77
C406 1-137-839-11 ELECT 2200uF 20% 50V D443 8-719-991-33 DIODE 1SS133T-77
(EXCEPT AEP, UK) D481 8-719-991-33 DIODE 1SS133T-77
C407 1-162-306-11 CERAMIC 0.01uF 20% 16V
C408 1-162-306-11 CERAMIC 0.01uF 20% 16V D482 8-719-991-33 DIODE 1SS133T-77
C411 1-162-306-11 CERAMIC 0.01uF 20% 16V D483 8-719-991-33 DIODE 1SS133T-77
(EXCEPT AEP, UK)
< EARTH TERMINAL >
C441 1-126-964-11 ELECT 10uF 20% 50V
C442 1-126-964-11 ELECT 10uF 20% 50V EP401 1-537-771-21 TERMINAL BOARD, GROUND
C443 1-162-294-31 CERAMIC 0.001uF 10% 50V EP402 1-537-771-21 TERMINAL BOARD, GROUND
C444 1-162-294-31 CERAMIC 0.001uF 10% 50V EP491 1-537-771-21 TERMINAL BOARD, GROUND
C445 1-162-282-31 CERAMIC 100PF 10% 50V (EXCEPT AEP, UK)
53
HCD-RG121
AMP BD80A
< IC > R466 1-247-873-91 CARBON 56K 5% 1/4W
R467 1-249-435-11 CARBON 33K 5% 1/4W
0 IC441 6-705-845-01 IC STK403-090 R481 1-247-847-91 CARBON 4.7K 5% 1/4W
R482 1-249-429-11 CARBON 10K 5% 1/4W
< TERMINAL BOARD > R483 1-247-791-91 CARBON 22 5% 1/4W
JK441 1-694-884-11 TERMINAL BOARD (4P) (SEAKER) R484 1-247-873-91 CARBON 56K 5% 1/4W
R485 1-247-879-91 CARBON 100K 5% 1/4W
< COIL > R486 1-247-879-91 CARBON 100K 5% 1/4W
R487 1-249-435-11 CARBON 33K 5% 1/4W
L441 1-422-009-13 COIL, AIR-CORE R488 1-247-863-91 CARBON 22K 5% 1/4W
L442 1-422-009-13 COIL, AIR-CORE
R489 1-247-847-91 CARBON 4.7K 5% 1/4W
< TRANSISTOR > R490 1-247-847-91 CARBON 4.7K 5% 1/4W
R491 1-247-863-91 CARBON 22K 5% 1/4W
Q441 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA R492 1-247-831-91 CARBON 1K 5% 1/4W
Q442 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA R493 1-249-435-11 CARBON 33K 5% 1/4W
Q481 8-729-119-79 TRANSISTOR 2SC2785-FEK
Q482 8-729-119-79 TRANSISTOR 2SC2785-FEK R494 1-249-421-11 CARBON 2.2K 5% 1/4W
Q483 8-729-119-79 TRANSISTOR 2SC2785-FEK 0 R495 1-202-972-61 FUSIBLE 1 5% 1/4W
0 R496 1-212-881-11 FUSIBLE 100 5% 1/4W
Q485 8-729-119-76 TRANSISTOR 2SA1175-HFE < RELAY >
Q487 8-729-119-79 TRANSISTOR 2SC2785-FEK RY441 1-755-373-11 RELAY
< THERMISTOR >
Q489 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
TH441 1-807-796-11 THERMISTOR
< RESISTOR > ************************************************************
R401 1-247-879-91 CARBON 100K 5% 1/4W A-4750-181-A BD80A BOARD, COMPLETE

R402 1-247-879-91 CARBON 100K 5% 1/4W **********************
R407 1-260-316-51 CARBON 100 5% 1/2W
R411 1-249-421-11 CARBON 2.2K 5% 1/4W < CAPACITOR >
R412 1-249-421-11 CARBON 2.2K 5% 1/4W
C10 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
R413 1-249-427-11 CARBON 6.8K 5% 1/4W C11 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
R414 1-249-427-11 CARBON 6.8K 5% 1/4W C14 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R441 1-247-831-91 CARBON 1K 5% 1/4W C15 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R442 1-247-831-91 CARBON 1K 5% 1/4W C16 1-115-156-11 CERAMIC CHIP 1uF 10V
R443 1-249-435-11 CARBON 33K 5% 1/4W
C17 1-126-923-91 ELECT 220uF 20% 10V
R444 1-249-435-11 CARBON 33K 5% 1/4W C18 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R446 1-247-831-91 CARBON 1K 5% 1/4W C112 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
R448 1-249-435-11 CARBON 33K 5% 1/4W
C114 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
0 R451 1-217-151-00 METAL 0.22 10% 2W C115 1-164-360-11 CERAMIC CHIP 0.1uF 16V
0 R452 1-217-151-00 METAL 0.22 10% 2W C116 1-126-923-91 ELECT 220uF 20% 10V
R453 1-260-076-11 CARBON 10 5% 1/2W C117 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R454 1-260-076-11 CARBON 10 5% 1/2W C122 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R455 1-247-831-91 CARBON 1K 5% 1/4W
C123 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R460 1-247-871-91 CARBON 47K 5% 1/4W
R463 1-260-076-11 CARBON 10 5% 1/2W C143 1-164-360-11 CERAMIC CHIP 0.1uF 16V
(AEP, UK) C151 1-126-923-91 ELECT 220uF 20% 10V
R464 1-260-076-11 CARBON 10 5% 1/2W
(AEP, UK) C160 1-164-360-11 CERAMIC CHIP 0.1uF 16V

54
HCD-RG121
BD80A CONNECT
C162 1-164-360-11 CERAMIC CHIP 0.1uF 16V R111 1-216-821-11 METAL CHIP 1K 5% 1/10W
C163 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R113 1-216-821-11 METAL CHIP 1K 5% 1/10W
C170 1-126-934-11 ELECT 220uF 20% 16V R114 1-216-835-11 METAL CHIP 15K 5% 1/10W
C171 1-162-919-11 CERAMIC CHIP 22PF 5% 50V R121 1-216-835-11 METAL CHIP 15K 5% 1/10W
C172 1-162-920-11 CERAMIC CHIP 27PF 5% 50V R131 1-216-857-11 METAL CHIP 1M 5% 1/10W
R133 1-216-848-11 METAL CHIP 180K 5% 1/10W
C182 1-164-360-11 CERAMIC CHIP 0.1uF 16V R141 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
C183 1-126-923-91 ELECT 220uF 20% 10V R142 1-216-821-11 METAL CHIP 1K 5% 1/10W
C184 1-126-923-91 ELECT 220uF 20% 10V R143 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
C186 1-164-315-11 CERAMIC CHIP 470PF 5% 50V R151 1-216-864-11 SHORT CHIP 0
R161 1-216-809-11 METAL CHIP 100 5% 1/10W
C195 1-164-360-11 CERAMIC CHIP 0.1uF 16V R171 1-216-817-11 METAL CHIP 470 5% 1/10W
C201 1-126-923-91 ELECT 220uF 20% 10V R172 1-216-857-11 METAL CHIP 1M 5% 1/10W
C203 1-126-923-91 ELECT 220uF 20% 10V R173 1-216-295-91 SHORT CHIP 0
R181 1-216-809-11 METAL CHIP 100 5% 1/10W
C210 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R182 1-216-809-11 METAL CHIP 100 5% 1/10W
C211 1-164-230-11 CERAMIC CHIP 220PF 5% 50V R201 1-500-445-21 FERRITE, EMI (SMD) (2012)
C212 1-162-919-11 CERAMIC CHIP 22PF 5% 50V R202 1-216-864-11 SHORT CHIP 0
C251 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V R204 1-500-445-21 FERRITE, EMI (SMD) (2012)
R251 1-216-833-11 METAL CHIP 10K 5% 1/10W
R408 1-216-809-11 METAL CHIP 100 5% 1/10W
< CONNECTOR > R409 1-216-809-11 METAL CHIP 100 5% 1/10W
R410 1-216-809-11 METAL CHIP 100 5% 1/10W
CN101 1-793-907-11 CONNECTOR, FFC/FPC 16P R411 1-216-809-11 METAL CHIP 100 5% 1/10W
CN201 1-568-860-11 SOCKET, CONNECTOR 17P R412 1-216-809-11 METAL CHIP 100 5% 1/10W
< IC > < SWITCH >
IC101 8-752-425-11 IC CXD3058AR S101 1-771-853-11 SWITCH,DETECTION (LIMIT)

IC251 6-705-808-01 IC BA5947FM
< VIBRATOR >
< SHORT >
X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz)
JR101 1-216-296-11 SHORT CHIP 0 ************************************************************
JR102 1-216-296-11 SHORT CHIP 0
JR103 1-216-296-11 SHORT CHIP 0 CONEECT BOARD, COMPLETE
JR104 1-216-296-11 SHORT CHIP 0 ************************
JR105 1-216-296-11 SHORT CHIP 0
< CAPACITOR >
JR106 1-216-296-11 SHORT CHIP 0
JR107 1-216-296-11 SHORT CHIP 0 C871 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
JR108 1-216-864-11 SHORT CHIP 0 C872 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
JR109 1-216-296-11 SHORT CHIP 0 C873 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
JR110 1-216-296-11 SHORT CHIP 0
< CONNECTOR >
JR111 1-216-296-11 SHORT CHIP 0
CN872 1-784-778-11 CONNECTOR, FFC 17P
< TRANSISTOR > CN873 1-568-826-11 CONNECTOR, FFC 7P
* CN874 1-564-725-11 PIN, CONNECTOR (SMALL TYPE) 9P
Q10 6-550-363-01 TRANSISTOR 2SB1690KT146
< FERRITE BEAD >
< RESISTOR >
FB871 1-216-864-11 SHORT CHIP 0
R10 1-216-791-11 METAL CHIP 3.3 5% 1/10W FB872 1-216-864-11 SHORT CHIP 0
R11 1-216-864-11 SHORT CHIP 0
R12 1-216-845-11 METAL CHIP 100K 5% 1/10W
R13 1-218-446-11 METAL CHIP 1 5% 1/10W
55
HCD-RG121
CONNECT DRIVER GAME JACK H/P JACK MAIN

< SHORT > C803 1-165-128-11 CERAMIC CHIP 0.22uF 16V
JR871 1-216-864-11 SHORT CHIP 0
JR872 1-216-864-11 SHORT CHIP 0 < JACK >
************************************************************
J804 1-815-684-11 JACK, PIN 3P (GAME INPUT)
1-687-135-12 DRIVER BOARD
************ < SHORT >
< CAPACITOR > JR801 1-216-864-11 SHORT CHIP 0
C715 1-126-933-11 ELECT 100uF 20% 16V < RESISTOR >

C731 1-126-964-11 ELECT 10uF 20% 50V
C735 1-164-159-21 CERAMIC 0.1uF 50V R801 1-216-833-11 METAL CHIP 10K 5% 1/10W
R804 1-216-837-11 METAL CHIP 22K 5% 1/10W
C741 1-162-306-11 CERAMIC 0.01uF 20% 16V ************************************************************
C751 1-162-306-11 CERAMIC 0.01uF 20% 16V
C752 1-164-159-21 CERAMIC 0.1uF 50V H/P JACK BOARD
**************
< CONNECTOR >
< CAPACITOR >
CN701 1-785-338-11 PIN, CONNECTOR (LIGHT ANGLE) 12P
CN702 1-784-766-11 CONNECTOR, FFC 5P C830 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
* CN703 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P C831 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
CN704 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P C832 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< DIODE > < JACK >
D701 8-719-921-42 DIODE MTZJ-5.1A J801 1-793-829-11 JACK, HEADPHONE (PHONE)

D711 8-719-109-69 DIODE RD3.6ESB2 ************************************************************
< IC > A-4750-781-A MAIN BOARD, COMPLETE (AEP, UK)

A-4751-789-A MAIN BOARD, COMPLETE (EXCEPT AEP, UK)
IC701 8-759-598-69 IC BA6956AN *********************
IC712 8-759-598-69 IC BA6956AN
7-685-872-09 SCREW +BVTT 3X8 (S)
< TRANSISTOR >
< CAPACITOR >
Q731 8-729-029-66 TRANSISTOR DTC114ESA
C101 1-126-960-11 ELECT 1uF 20% 50V
< RESISTOR > C102 1-126-960-11 ELECT 1uF 20% 50V
C103 1-126-956-91 ELECT 0.1uF 20% 50V
R701 1-249-413-11 CARBON 470 5% 1/4W C104 1-126-956-91 ELECT 0.1uF 20% 50V
R702 1-247-807-31 CARBON 100 5% 1/4W C105 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
R711 1-249-417-11 CARBON 1K 5% 1/4W
R712 1-249-425-11 CARBON 4.7K 5% 1/4W C106 1-131-679-31 FILM 0.01uF 5% 50V
R713 1-249-433-11 CARBON 22K 5% 1/4W C107 1-126-964-11 ELECT 10uF 20% 50V
R721 1-249-425-11 CARBON 4.7K 5% 1/4W C109 1-131-679-31 FILM 0.01uF 5% 50V
R722 1-249-425-11 CARBON 4.7K 5% 1/4W C110 1-126-964-11 ELECT 10uF 20% 50V
R723 1-249-425-11 CARBON 4.7K 5% 1/4W
R731 1-247-807-31 CARBON 100 5% 1/4W C111 1-126-960-11 ELECT 1uF 20% 50V
C113 1-126-960-11 ELECT 1uF 20% 50V
R734 1-249-430-11 CARBON 12K 5% 1/4W C115 1-131-679-31 FILM 0.01uF 5% 50V
R735 1-247-807-31 CARBON 100 5% 1/4W
R751 1-249-425-11 CARBON 4.7K 5% 1/4W C116 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
************************************************************ C117 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C118 1-126-964-11 ELECT 10uF 20% 50V
GAME JACK BOARD C119 1-131-679-31 FILM 0.01uF 5% 50V
**************** C120 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
< CAPACITOR > C121 1-164-816-11 CERAMIC CHIP 220PF 2% 50V

C122 1-126-964-11 ELECT 10uF 20% 50V
C801 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C123 1-126-965-91 ELECT 22uF 20% 50V
C802 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C124 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
56
HCD-RG121
MAIN
C125 1-162-953-11 CERAMIC CHIP 100PF 5% 50V C209 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V
(AEP, UK)
C126 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V C211 1-109-953-11 ELECT 2.2uF 20% 50V
C127 1-104-658-91 ELECT 100uF 20% 10V
C128 1-104-658-91 ELECT 100uF 20% 10V C212 1-126-964-11 ELECT 10uF 20% 50V
C135 1-131-690-31 FILM 0.068uF 5% 50V C217 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C136 1-131-690-31 FILM 0.068uF 5% 50V
C137 1-126-964-11 ELECT 10uF 20% 50V C222 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C138 1-126-964-11 ELECT 10uF 20% 50V C231 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C139 1-131-690-31 FILM 0.068uF 5% 50V C235 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C140 1-131-690-31 FILM 0.068uF 5% 50V C242 1-130-479-00 MYLAR 0.0047uF 5% 50V
C141 1-126-964-11 ELECT 10uF 20% 50V
C142 1-126-964-11 ELECT 10uF 20% 50V C243 1-131-681-31 FILM 0.015uF 5% 50V
C143 1-126-960-11 ELECT 1uF 20% 50V C244 1-131-681-31 FILM 0.015uF 5% 50V
C144 1-136-165-00 FILM 0.1uF 5% 50V C246 1-131-681-31 FILM 0.015uF 5% 50V
C146 1-136-165-00 FILM 0.1uF 5% 50V
C148 1-131-679-31 FILM 0.01uF 5% 50V C251 1-126-947-11 ELECT 47uF 20% 35V
C149 1-131-679-31 FILM 0.01uF 5% 50V C252 1-126-933-11 ELECT 100uF 20% 16V
C253 1-126-956-91 ELECT 0.1uF 20% 50V
C150 1-131-679-31 FILM 0.01uF 5% 50V C258 1-126-959-11 ELECT 0.47uF 20% 50V
C151 1-131-679-31 FILM 0.01uF 5% 50V
C152 1-130-475-00 MYLAR 0.0022uF 5% 50V C259 1-126-957-11 ELECT 0.22uF 20% 50V
C153 1-130-475-00 MYLAR 0.0022uF 5% 50V C264 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V
C154 1-131-700-31 FILM 0.47uF 5% 50V C265 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V
C157 1-126-960-11 ELECT 1uF 20% 50V C267 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V
C159 1-126-960-11 ELECT 1uF 20% 50V
C161 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V C271 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V
(AEP, UK) (AEP, UK)
(AEP, UK)
C163 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V C274 1-162-949-11 CERAMIC CHIP 47PF 5% 50V
(AEP, UK) C275 1-162-949-11 CERAMIC CHIP 47PF 5% 50V
C164 1-126-960-11 ELECT 1uF 20% 50V
C165 1-126-960-11 ELECT 1uF 20% 50V C276 1-164-362-11 CERAMIC CHIP 470PF 5% 50V
C166 1-126-960-11 ELECT 1uF 20% 50V (AEP, UK)
C175 1-109-953-11 ELECT 2.2uF 20% 50V C277 1-164-362-11 CERAMIC CHIP 470PF 5% 50V
(AEP, UK)
C177 1-162-945-11 CERAMIC CHIP 22PF 5% 50V (AEP, UK)
C179 1-162-949-11 CERAMIC CHIP 47PF 5% 50V (AEP, UK)
C181 1-162-949-11 CERAMIC CHIP 47PF 5% 50V C280 1-164-362-11 CERAMIC CHIP 470PF 5% 50V
(AEP, UK)
C185 1-126-964-11 ELECT 10uF 20% 50V (AEP, UK)
C187 1-162-974-11 CERAMIC CHIP 0.01uF 50V (AEP, UK)
C188 1-126-965-91 ELECT 22uF 20% 50V (AEP, UK)
C190 1-162-974-11 CERAMIC CHIP 0.01uF 50V (AEP, UK)
C191 1-126-961-11 ELECT 2.2uF 20% 50V C301 1-136-165-00 FILM 0.1uF 5% 50V
C192 1-126-961-11 ELECT 2.2uF 20% 50V
C302 1-136-165-00 FILM 0.1uF 5% 50V
C193 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C303 1-136-165-00 FILM 0.1uF 5% 50V
(AEP, UK) C306 1-136-165-00 FILM 0.1uF 5% 50V
57
HCD-RG121
MAIN
C308 1-126-965-91 ELECT 22uF 20% 50V D316 8-719-988-61 DIODE 1SS355TE-17
C311 1-126-964-11 ELECT 10uF 20% 50V D324 6-500-522-21 DIODE 10EDB40-TB3
C312 1-126-964-11 ELECT 10uF 20% 50V
D325 6-500-522-21 DIODE 10EDB40-TB3
C313 1-126-943-11 ELECT 2200uF 20% 25V D326 6-500-522-21 DIODE 10EDB40-TB3
C315 1-126-933-11 ELECT 100uF 20% 16V
C316 1-126-943-11 ELECT 2200uF 20% 25V < EARTH TERMINAL >
C318 1-126-933-11 ELECT 100uF 20% 16V
C321 1-126-961-11 ELECT 2.2uF 20% 50V EP101 1-537-771-21 TERMINAL BOARD, GROUND
EP301 1-537-771-21 TERMINAL BOARD, GROUND
C351 1-164-357-11 CERAMIC CHIP 0.001uF 5% 50V < FERRITE BEAD >
C352 1-126-965-91 ELECT 22uF 20% 50V
C353 1-126-961-11 ELECT 2.2uF 20% 50V FB201 1-216-864-11 SHORT CHIP 0
C354 1-164-156-11 CERAMIC CHIP 0.1uF 25V FB202 1-216-864-11 SHORT CHIP 0
FB203 1-216-864-11 SHORT CHIP 0
C371 1-164-362-11 CERAMIC CHIP 470PF 5% 50V FB204 1-216-864-11 SHORT CHIP 0
C372 1-162-953-11 CERAMIC CHIP 100PF 5% 50V FB205 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
C374 1-126-947-11 ELECT 47uF 20% 35V FB205 1-543-958-22 BEAD, FERRITE (CHIP) (1608) (AEP, UK)
< IC >
C376 1-126-961-11 ELECT 2.2uF 20% 50V
IC101 6-705-852-01 IC BD3401KS2
< CONNECTOR > IC102 8-759-710-97 IC NJM4565M-D
IC201 8-759-508-69 IC BA3126N
CN101 1-568-830-11 CONNECTOR, FFC 11P (EXCEPT AEP, UK) IC301 6-702-771-01 IC TA78033LS
CN101 1-784-776-11 CONNECTOR, FFC 15P (AEP, UK) IC302 6-702-771-01 IC TA78033LS
* CN112 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3P IC303 8-759-701-59 IC NJM78M09FA
* CN301 1-568-950-11 PIN, CONNECTOR 12P IC304 8-759-701-59 IC NJM78M09FA
IC371 6-704-046-01 IC BU2099FV
CN302 1-568-844-11 CONNECTOR, FFC 29P (EXCEPT AEP, UK)
CN302 1-784-792-11 CONNECTOR, FFC 31P (AEP, UK) < COIL >
CN305 1-568-937-11 PIN, CONNECTOR (STRAIGHT) 10P
CN307 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P L101 1-424-849-11 COIL, OSCILLATION (BIAS)
CN309 1-564-707-11 PIN, CONNECTOR (SMALL TYPE) 5P
< TRANSISTOR >
CN314 1-564-506-11 PLUG, CONNECTOR 3P
Q101 8-729-120-28 TRANSISTOR 2SC1623-L5L6
< DIODE > Q102 6-550-580-01 TRANSISTOR 2SA1235TP-1F
Q103 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
D201 8-719-988-61 DIODE 1SS355TE-17 Q104 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
D211 8-719-988-61 DIODE 1SS355TE-17 Q105 8-729-120-28 TRANSISTOR 2SC1623-L5L6
D212 8-719-988-61 DIODE 1SS355TE-17
D215 8-719-988-61 DIODE 1SS355TE-17 Q305 6-550-580-01 TRANSISTOR 2SA1235TP-1F
D301 6-500-522-21 DIODE 10EDB40-TB3 Q306 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
D302 6-500-522-21 DIODE 10EDB40-TB3
D303 6-500-522-21 DIODE 10EDB40-TB3 Q307 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
D304 6-500-522-21 DIODE 10EDB40-TB3 Q308 6-550-580-01 TRANSISTOR 2SA1235TP-1F
D305 6-500-522-21 DIODE 10EDB40-TB3 Q312 8-729-041-19 TRANSISTOR 2SA953-T-K
D306 6-500-522-21 DIODE 10EDB40-TB3 Q313 8-729-120-28 TRANSISTOR 2SC1623-L5L6
D307 6-500-522-21 DIODE 10EDB40-TB3
Q321 8-729-142-46 TRANSISTOR 2SC2001-LK
D312 6-500-522-21 DIODE 10EDB40-TB3
D313 8-719-085-36 DIODE 11EQS04-TB5 Q324 8-729-140-04 TRANSISTOR 2SB1116A-L
58
HCD-RG121
MAIN
Q361 6-550-580-01 TRANSISTOR 2SA1235TP-1F R170 1-216-833-11 METAL CHIP 10K 5% 1/10W
R171 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R171 1-216-833-11 METAL CHIP 10K 5% 1/10W
< RESISTOR > R172 1-216-809-11 METAL CHIP 100 5% 1/10W
R173 1-216-833-11 METAL CHIP 10K 5% 1/10W
R101 1-216-833-11 METAL CHIP 10K 5% 1/10W R174 1-216-833-11 METAL CHIP 10K 5% 1/10W
R103 1-216-851-11 METAL CHIP 330K 5% 1/10W
R105 1-216-816-11 METAL CHIP 390 5% 1/10W R177 1-216-849-11 METAL CHIP 220K 5% 1/10W
R194 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R106 1-216-851-11 METAL CHIP 330K 5% 1/10W R195 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R107 1-216-835-11 METAL CHIP 15K 5% 1/10W R197 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R108 1-216-816-11 METAL CHIP 390 5% 1/10W
R202 1-216-833-11 METAL CHIP 10K 5% 1/10W
R113 1-216-851-11 METAL CHIP 330K 5% 1/10W
R115 1-216-857-11 METAL CHIP 1M 5% 1/10W R206 1-216-841-11 METAL CHIP 47K 5% 1/10W
R207 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R119 1-216-841-11 METAL CHIP 47K 5% 1/10W
R120 1-216-857-11 METAL CHIP 1M 5% 1/10W R210 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R212 1-216-833-11 METAL CHIP 10K 5% 1/10W
R127 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R213 1-216-821-11 METAL CHIP 1K 5% 1/10W
R129 1-216-841-11 METAL CHIP 47K 5% 1/10W
R131 1-216-835-11 METAL CHIP 15K 5% 1/10W R216 1-216-806-11 METAL CHIP 56 5% 1/10W
R132 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R217 1-216-806-11 METAL CHIP 56 5% 1/10W
R218 1-215-891-11 METAL OXIDE 680 5% 2W
R133 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (AEP, UK)
R134 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R218 1-215-916-00 METAL OXIDE 680 5% 3W
R135 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (EXCEPT AEP, UK)
R136 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R219 1-215-891-11 METAL OXIDE 680 5% 2W
R137 1-216-833-11 METAL CHIP 10K 5% 1/10W (AEP, UK)
R138 1-216-821-11 METAL CHIP 1K 5% 1/10W R219 1-215-916-00 METAL OXIDE 680 5% 3W
R139 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
R151 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R222 1-216-830-11 METAL CHIP 5.6K 5% 1/10W
R223 1-216-864-11 SHORT CHIP 0
R152 1-216-833-11 METAL CHIP 10K 5% 1/10W
R243 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R157 1-216-841-11 METAL CHIP 47K 5% 1/10W
R248 1-216-833-11 METAL CHIP 10K 5% 1/10W
R162 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R166 1-216-833-11 METAL CHIP 10K 5% 1/10W R252 1-216-864-11 SHORT CHIP 0
R253 1-216-809-11 METAL CHIP 100 5% 1/10W
R167 1-216-833-11 METAL CHIP 10K 5% 1/10W
59
HCD-RG121
MAIN MOTOR (LD) MOTOR (TB) PANEL

R263 1-216-857-11 METAL CHIP 1M 5% 1/10W R386 1-216-837-11 METAL CHIP 22K 5% 1/10W
R389 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R272 1-216-853-11 METAL CHIP 470K 5% 1/10W
R273 1-216-864-11 SHORT CHIP 0 R391 1-216-833-11 METAL CHIP 10K 5% 1/10W
R394 1-216-821-11 METAL CHIP 1K 5% 1/10W
R282 1-216-825-11 METAL CHIP 2.2K 5% 1/10W ************************************************************
R283 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R284 1-216-825-11 METAL CHIP 2.2K 5% 1/10W 1-687-133-12 MOTOR (LD) BOARD
R306 1-216-833-11 METAL CHIP 10K 5% 1/10W ****************
R307 1-216-833-11 METAL CHIP 10K 5% 1/10W ************************************************************

R308 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R310 1-216-833-11 METAL CHIP 10K 5% 1/10W 1-687-134-12 MOTOR (TB) BOARD
R311 1-216-829-11 METAL CHIP 4.7K 5% 1/10W ****************
R312 1-216-837-11 METAL CHIP 22K 5% 1/10W
< CONNECTOR >
R313 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R321 1-216-829-11 METAL CHIP 4.7K 5% 1/10W CN742 1-784-727-11 CONNECTOR, FFC 5P
R322 1-216-837-11 METAL CHIP 22K 5% 1/10W ************************************************************
R323 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R324 1-216-833-11 METAL CHIP 10K 5% 1/10W A-4751-560-A PANEL BOARD, COMPLETE (AEP, UK)
A-4751-568-A PANEL BOARD, COMPLETE (MX, AR, E2, E51)
R325 1-216-829-11 METAL CHIP 4.7K 5% 1/10W A-4751-576-A PANEL BOARD, COMPLETE (SP, E3, AUS)
R341 1-216-833-11 METAL CHIP 10K 5% 1/10W A-4752-234-A PANEL BOARD, COMPLETE (EA)
R342 1-216-821-11 METAL CHIP 1K 5% 1/10W **********************
R343 1-216-837-11 METAL CHIP 22K 5% 1/10W
R344 1-216-837-11 METAL CHIP 22K 5% 1/10W
< CAPACITOR >
R345 1-216-833-11 METAL CHIP 10K 5% 1/10W
R346 1-216-821-11 METAL CHIP 1K 5% 1/10W C605 1-126-163-11 ELECT 4.7uF 20% 50V
R347 1-216-837-11 METAL CHIP 22K 5% 1/10W C606 1-115-156-11 CERAMIC CHIP 1uF 10V
R348 1-216-837-11 METAL CHIP 22K 5% 1/10W C607 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R351 1-216-835-11 METAL CHIP 15K 5% 1/10W C608 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C609 1-115-156-11 CERAMIC CHIP 1uF 10V
R352 1-216-845-11 METAL CHIP 100K 5% 1/10W
R353 1-216-841-11 METAL CHIP 47K 5% 1/10W C610 1-126-916-11 ELECT 1000uF 20% 6.3V
R354 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C611 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R356 1-216-817-11 METAL CHIP 470 5% 1/10W C612 1-126-157-11 ELECT 10uF 20% 16V
R357 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C613 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R358 1-216-809-11 METAL CHIP 100 5% 1/10W
R362 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C617 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R363 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C618 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R364 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C619 1-124-589-11 ELECT 47uF 20% 16V
C620 1-119-772-91 ELECT 47uF 20% 35V
R371 1-216-809-11 METAL CHIP 100 5% 1/10W
R372 1-216-809-11 METAL CHIP 100 5% 1/10W C621 1-162-995-11 CERAMIC CHIP 0.022uF 50V
R373 1-216-809-11 METAL CHIP 100 5% 1/10W C622 1-126-163-11 ELECT 4.7uF 20% 50V
R375 1-216-833-11 METAL CHIP 10K 5% 1/10W C624 1-162-918-11 CERAMIC CHIP 18PF 5% 50V
R376 1-216-833-11 METAL CHIP 10K 5% 1/10W
R377 1-216-833-11 METAL CHIP 10K 5% 1/10W C626 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R381 1-216-833-11 METAL CHIP 10K 5% 1/10W
R385 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C635 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
60
HCD-RG121
PANEL
C636 1-162-927-11 CERAMIC CHIP 100PF 5% 50V IC603 6-704-045-01 IC MM1574ANLE
IC604 8-759-533-04 IC M62703ML-E1
C638 1-162-927-11 CERAMIC CHIP 100PF 5% 50V < SHORT >
C640 1-162-927-11 CERAMIC CHIP 100PF 5% 50V JR604 1-216-864-11 SHORT CHIP 0
C641 1-164-156-11 CERAMIC CHIP 0.1uF 25V JR605 1-216-864-11 SHORT CHIP 0
JR606 1-216-864-11 SHORT CHIP 0
C642 1-164-156-11 CERAMIC CHIP 0.1uF 25V JR611 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
C643 1-164-156-11 CERAMIC CHIP 0.1uF 25V JR612 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
C646 1-124-234-00 ELECT 22uF 20% 16V
C647 1-124-589-11 ELECT 47uF 20% 16V JR613 1-216-864-11 SHORT CHIP 0
C648 1-124-234-00 ELECT 22uF 20% 16V JR617 1-216-864-11 SHORT CHIP 0
JR621 1-216-864-11 SHORT CHIP 0
C649 1-164-156-11 CERAMIC CHIP 0.1uF 25V JR622 1-216-864-11 SHORT CHIP 0
C653 1-162-959-11 CERAMIC CHIP 330PF 5% 50V JR623 1-216-864-11 SHORT CHIP 0
C655 1-164-156-11 CERAMIC CHIP 0.1uF 25V < LED >
LED601 6-500-809-01 DIODE SELU5223C-STP15 (]/1)
< CONNECTOR >
< TRANSISTOR >
CN601 1-784-751-11 CONNECTOR, FFC 29P (EXCEPT AEP, UK)
CN601 1-784-753-11 CONNECTOR, FFC 31P (AEP, UK) Q601 8-729-116-57 TRANSISTOR 2SB1068-K
CN602 1-784-774-11 CONNECTOR, FFC 13P Q602 8-729-140-04 TRANSISTOR 2SB1116A-L
CN603 1-568-826-11 CONNECTOR, FFC 7P Q603 8-729-140-04 TRANSISTOR 2SB1116A-L
* CN604 1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P Q604 8-729-119-76 TRANSISTOR 2SA1175-HFE
CN608 1-818-282-11 PIN, CONNECTOR 3P
Q606 8-729-027-55 TRANSISTOR DTC143EKA-T146
< DIODE > Q607 8-729-027-55 TRANSISTOR DTC143EKA-T146
Q608 8-729-027-55 TRANSISTOR DTC143EKA-T146
D603 8-719-988-61 DIODE 1SS355TE-17 Q610 8-729-027-55 TRANSISTOR DTC143EKA-T146
D604 8-719-988-61 DIODE 1SS355TE-17 Q616 8-729-027-55 TRANSISTOR DTC143EKA-T146
D605 8-719-988-61 DIODE 1SS355TE-17
* D606 6-500-486-01 DIODE PTZ-TE25-11B (EXCEPT AEP, UK) < RESISTOR >
D607 8-719-988-61 DIODE 1SS355TE-17
R601 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D608 8-719-988-61 DIODE 1SS355TE-17 R602 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D610 8-719-056-78 DIODE UDZ-TE-17-4.3B R604 1-216-841-11 METAL CHIP 47K 5% 1/10W
D613 8-719-988-61 DIODE 1SS355TE-17
R606 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D614 8-719-988-61 DIODE
1SS355TE-17 R607 1-216-841-11 METAL CHIP 47K 5% 1/10W
D615 8-719-988-61 DIODE
1SS355TE-17 R608 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D616 8-719-988-61 DIODE
D620 8-719-988-61 DIODE
(AEP, UK, MX, AR, E2, E51)
D621 8-719-988-61 DIODE 1SS355TE-17 R611 1-216-837-11 METAL CHIP 22K 5% 1/10W
(AEP, UK, MX, AR, E2, E51) R612 1-216-833-11 METAL CHIP 10K 5% 1/10W
R613 1-216-837-11 METAL CHIP 22K 5% 1/10W
D622 8-719-988-61 DIODE 1SS355TE-17 (AEP, UK, EA) R614 1-216-837-11 METAL CHIP 22K 5% 1/10W
(AEP, UK, MX, AR, E2, E51)
D631 8-719-978-33 DIODE DTZ-TT11-6.8B R618 1-216-833-11 METAL CHIP 10K 5% 1/10W
R619 1-216-837-11 METAL CHIP 22K 5% 1/10W
D632 8-719-083-57 DIODE UDZSTE-173.6B R620 1-216-837-11 METAL CHIP 22K 5% 1/10W
D633 8-719-988-61 DIODE 1SS355TE-17
R621 1-216-833-11 METAL CHIP 10K 5% 1/10W
< FILTER > R622 1-216-049-11 RES-CHIP 1K 5% 1/10W
R623 1-216-833-11 METAL CHIP 10K 5% 1/10W
FL601 1-518-976-11 INDICATOR TUBE, FLUORESCENT R624 1-216-049-11 RES-CHIP 1K 5% 1/10W
R625 1-216-833-11 METAL CHIP 10K 5% 1/10W
< IC >
R626 1-216-049-11 RES-CHIP 1K 5% 1/10W
IC601 6-804-129-01 IC LC876972B-52S2-E R627 1-216-833-11 METAL CHIP 10K 5% 1/10W
61
HCD-RG121
PANEL
R629 1-216-150-91 RES-CHIP 10 5% 1/8W R693 1-216-809-11 METAL CHIP 100 5% 1/10W
R630 1-216-809-11 METAL CHIP 100 5% 1/10W
(AEP, UK) R694 1-216-809-11 METAL CHIP 100 5% 1/10W
R695 1-216-809-11 METAL CHIP 100 5% 1/10W
R631 1-216-809-11 METAL CHIP 100 5% 1/10W R696 1-216-809-11 METAL CHIP 100 5% 1/10W
(AEP, UK) R697 1-216-809-11 METAL CHIP 100 5% 1/10W
R635 1-216-809-11 METAL CHIP 100 5% 1/10W R698 1-216-182-00 RES-CHIP 220 5% 1/8W
R639 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R712 1-216-797-11 METAL CHIP 10 5% 1/10W
R644 1-216-821-11 METAL CHIP 1K 5% 1/10W
R717 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R649 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R650 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R720 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R722 1-216-835-11 METAL CHIP 15K 5% 1/10W
R653 1-216-817-11 METAL CHIP 470 5% 1/10W R727 1-220-397-11 METAL CHIP 4.7M 5% 1/10W
R654 1-216-819-11 METAL CHIP 680 5% 1/10W
R655 1-216-821-11 METAL CHIP 1K 5% 1/10W R728 1-220-397-11 METAL CHIP 4.7M 5% 1/10W
R730 1-216-809-11 METAL CHIP 100 5% 1/10W
R659 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R661 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R735 1-216-821-11 METAL CHIP 1K 5% 1/10W
R736 1-216-821-11 METAL CHIP 1K 5% 1/10W
R664 1-216-817-11 METAL CHIP 470 5% 1/10W
R741 1-216-845-11 METAL CHIP 100K 5% 1/10W
R669 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R746 1-216-845-11 METAL CHIP 100K 5% 1/10W
R676 1-216-835-11 METAL CHIP 15K 5% 1/10W
R751 1-216-845-11 METAL CHIP 100K 5% 1/10W
R679 1-216-172-00 RES-CHIP 82 5% 1/8W R752 1-216-845-11 METAL CHIP 100K 5% 1/10W
R681 1-216-849-11 METAL CHIP 220K 5% 1/10W
R756 1-216-845-11 METAL CHIP 100K 5% 1/10W
R686 1-216-841-11 METAL CHIP 47K 5% 1/10W
R761 1-216-845-11 METAL CHIP 100K 5% 1/10W
R691 1-216-809-11 METAL CHIP 100 5% 1/10W
62
HCD-RG121
PANEL REM SENSOR SUB-TRANS

R764 1-216-845-11 METAL CHIP 100K 5% 1/10W S646 1-762-875-21 SWITCH, KEYBOARD (M)
R765 1-216-845-11 METAL CHIP 100K 5% 1/10W
R766 1-216-845-11 METAL CHIP 100K 5% 1/10W S647 1-762-875-21 SWITCH, KEYBOARD (m)
R767 1-216-845-11 METAL CHIP 100K 5% 1/10W S648 1-762-875-21 SWITCH, KEYBOARD (X)
R768 1-216-845-11 METAL CHIP 100K 5% 1/10W S649 1-762-875-21 SWITCH, KEYBOARD (x)
S650 1-762-875-21 SWITCH, KEYBOARD (TUNING -)
R769 1-216-845-11 METAL CHIP 100K 5% 1/10W
R770 1-216-845-11 METAL CHIP 100K 5% 1/10W < VIBRATOR >
R771 1-216-841-11 METAL CHIP 47K 5% 1/10W
R772 1-216-821-11 METAL CHIP 1K 5% 1/10W X601 1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
R773 1-216-809-11 METAL CHIP 100 5% 1/10W X602 1-795-004-21 VIBRATOR, CERAMIC (10MHz)
************************************************************
R774 1-216-809-11 METAL CHIP 100 5% 1/10W
R775 1-216-809-11 METAL CHIP 100 5% 1/10W REM BOARD
R776 1-216-817-11 METAL CHIP 470 5% 1/10W **********
R777 1-216-809-11 METAL CHIP 100 5% 1/10W
R778 1-216-809-11 METAL CHIP 100 5% 1/10W < CONNECTOR >
R784 1-216-809-11 METAL CHIP 100 5% 1/10W CN610 1-816-423-11 SOCKET, CONNECTOR 3P
R786 1-216-833-11 METAL CHIP 10K 5% 1/10W
R788 1-216-809-11 METAL CHIP 100 5% 1/10W < IC >
R789 1-216-841-11 METAL CHIP 47K 5% 1/10W
R790 1-216-821-11 METAL CHIP 1K 5% 1/10W IC610 6-600-174-01 IC RPM7240-H4 ( )
R791 1-216-809-11 METAL CHIP 100 5% 1/10W < SHORT >

R792 1-216-809-11 METAL CHIP 100 5% 1/10W
R793 1-216-809-11 METAL CHIP 100 5% 1/10W JR624 1-216-296-11 SHORT CHIP 0
R794 1-216-809-11 METAL CHIP 100 5% 1/10W ************************************************************
R795 1-216-809-11 METAL CHIP 100 5% 1/10W
1-687-132-12 SENSOR BOARD
R796 1-216-809-11 METAL CHIP 100 5% 1/10W *************
R797 1-216-821-11 METAL CHIP 1K 5% 1/10W
R798 1-216-821-11 METAL CHIP 1K 5% 1/10W < CONNECTOR >
R799 1-216-821-11 METAL CHIP 1K 5% 1/10W
R854 1-216-813-11 METAL CHIP 220 5% 1/10W CN731 1-785-329-21 PIN, CONNECTOR (LIGHT ANGLE) 3P
R863 1-216-170-00 RES-CHIP 68 5% 1/8W < IC >
< SWITCH > IC731 6-600-022-01 IC RPI-576

************************************************************
S601 1-762-875-21 SWITCH, KEYBOARD (]/1)
S602 1-762-875-21 SWITCH, KEYBOARD (DISLAY) SUB-TRANS BOARD
S603 1-762-875-21 SWITCH, KEYBOARD (EQ BAND) ****************
S604 1-762-875-21 SWITCH, KEYBOARD (DISC 1)
S605 1-762-875-21 SWITCH, KEYBOARD (DISC 2) < CONNECTOR >
S606 1-762-875-21 SWITCH, KEYBOARD (DISC 3) CN901 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
S607 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)
S608 1-762-875-21 SWITCH, KEYBOARD (Z) < DIODE >
S610 1-762-875-21 SWITCH, KEYBOARD (P FILE)
S611 1-762-875-21 EQSWITCH, KEYBOARD (PRESET EQ) D901 8-719-991-33 DIODE 1SS133T-77
D902 6-500-522-21 DIODE 10EDB40-TB3
S612 1-762-875-21 SWITCH, KEYBOARD (ENTER) D903 6-500-522-21 DIODE 10EDB40-TB3
S621 1-762-875-21 SWITCH, KEYBOARD (CD) D904 6-500-522-21 DIODE 10EDB40-TB3
S622 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND) D905 6-500-522-21 DIODE 10EDB40-TB3
S623 1-762-875-21 SWITCH, KEYBOARD (TAPE A/B)
S624 1-762-875-21 SWITCH, KEYBOARD (GAME) < TRANSFORMER >
S627 1-762-875-21 SWITCH, KEYBOARD PT902 X-4956-293-1 SUB TRANS ASSY (AEP, UK)
(PLAY MODE/TUNING MODE) PT902 X-4956-294-1 TRANS ASSY, SUB (SP, E2, E3, E51, AR, AUS)
S628 1-762-875-21 SWITCH, KEYBOARD (GAME MIXING) PT902 X-4956-322-1 SUB TRANS ASSY (EA, MX)
S629 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)
S630 1-762-875-21 SWITCH, KEYBOARD (REC PAUSE/START) < RELAY >
S641 1-762-875-21 SWITCH, KEYBOARD (GROOVE)
0 RY901 1-755-276-11 RELAY, POWER
S642 1-762-875-21 SWITCH, KEYBOARD (SURROUND)
S643 1-762-875-21 SWITCH, KEYBOARD (EFFECT ON/OFF)
S644 1-762-875-21 SWITCH, KEYBOARD (TUNING +)
S645 1-762-875-21 SWITCH, KEYBOARD (H)
63
HCD-RG121
SW TRANS TRANSLATION VIDEO OUT

< SWITCH > TRANSLATION BOARD (AEP, UK)
**************************
0 S901 1-786-055-21 SELECTOR, VOLTAGE (VOLTAGE SELECTOR)
(EA, SP, E2, E3, E51) < CAPACITOR >
************************************************************
1-687-669-12 SW BOARD (AEP, UK)
*********
< EARTH TERMINAL >
< SWITCH >
EP802 1-537-771-21 TERMINAL BOARD, GROUND (AEP, UK)
S751 1-786-514-11 SWITCH, LEVER (SLIDE) (LEVER) ************************************************************
************************************************************
VIDEO OUT BOARD
A-4750-786-A TRANS BOARD, COMPLETE (AEP, UK) ***************
A-4751-570-A TRANS BOARD, COMPLETE (SP, E2, E3, E51)
A-4752-237-A TRANS BOARD, COMPLETE (EA) < CONNECTOR >
A-4752-243-A TRANS BOARD, COMPLETE (AR, AUS)
A-4752-254-A TRANS BOARD, COMPLETE (MX) * CN805 1-564-704-11 PIN, CONNECTOR (SMALL TYPE) 2P
**********************
< JACK >
< CAPACITOR >
J803 1-774-227-11 JACK, PIN 1P (VIDEO OUT)
C906 1-164-159-11 CERAMIC 0.1uF 50V ************************************************************
C908 1-128-553-11 ELECT 220uF 20% 63V
C909 1-126-964-11 ELECT 10uF 20% 50V MISCELLANEOUS
C910 1-126-968-11 ELECT 100uF 20% 50V **************
C911 1-126-942-61 ELECT 1000uF 20% 25V
8 1-769-940-11 WIRE (FLAT TYPE) (11 CORE) (UK)
C920 1-131-679-31 FILM 0.01uF 5% 50V 9 1-693-615-11 TUNER (FM/AM) (EXCEPT AEP,AUS)
C921 1-131-679-31 FILM 0.01uF 5% 50V 9 1-693-616-11 TUNER (FM/AM) (AEP, UK)
C922 1-131-679-31 FILM 0.01uF 5% 50V 10 1-400-285-11 F-BEAD, E2515MRT
C923 1-131-679-31 FILM 0.01uF 5% 50V 64 1-769-975-11 WIRE (FLAT TYPE) (13 CORE)
C924 1-136-165-00 FILM 0.1uF 5% 50V
C925 1-136-165-00 FILM 0.1uF 5% 50V 69 1-796-485-51 DECK, MECHANICAL (CWM43FF-05)
C926 1-164-159-11 CERAMIC 0.1uF 50V 73 1-773-317-11 WIRE (FLAT TYPE) (31 CORE) (AEP, UK)
0 103 1-696-570-11 CORD, POWER (EA)
< CONNECTOR > 0 103 1-696-848-12 CORD, POWER (AUS)
CN904 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P 0 103 1-777-071-83 CORD, POWER (AEP, UK, SP, E51)
(AEP, UK, MX, AR, AUS) 0 103 1-783-941-22 CORD, POWER (AR)
CN904 1-568-106-11 PIN, CONNECTOR (3.96mm PITCH) 4P 0 103 1-827-226-11 CORD, POWER (MX, E2, E3)
(SP, EA, E2, E3, E51) 152 1-776-182-11 WIRE (FLAT TYPE) (5 CORE)
CN905 1-564-506-11 PLUG, CONNECTOR 3P 226 1-827-991-11 WIRE (FLAT TYPE) (16 CORE)
* CN907 1-764-333-11 PLUG, CONNECTOR 10P 227 1-773-050-11 WIRE (FLAT TYPE) (17 CORE)
0 229 8-820-116-02 OPTICAL PICK-UP KSM-213DCP/Z-NP
< DIODE > 230 1-471-035-11 MAGNET ASSY
233 1-469-854-11 CORE, FERRITE
D906 8-719-983-79 DIODE MTZJ-T-72-27D 0 F904 1-533-473-12 FUSE, GLASS TUBE (DIA. 5) (T6.3AL/250V)
D908 6-500-522-21 DIODE 10EDB40-TB3
< TRANSISTOR > 0 F906 1-533-470-12 FUSE, GLASS TUBE (DIA. 5) (T3.15AL/250V)
Q902 8-729-048-52 TRANSISTOR 2SA1932 (TP) M741 A-4723-963-A MOTOR ASSY, TABLE
M751 A-4736-655-A MOTOR ASSY, LOADING
< RESISTOR >
0 PT901 1-443-235-11 TRANSFORMER, POWER (AEP, UK)
R903 1-249-430-11 CARBON 12K 5% 1/4W 0 PT901 1-443-238-11 TRANSFORMER, POWER
R904 1-247-831-91 CARBON 1K 5% 1/4W (SP, AR, E2, E3, E51, AUS)
0 R908 1-202-972-61 FUSIBLE 1 5% 1/4W 0 PT901 1-443-280-11 TRANSFORMER, POWER (EA)
************************************************************ 0 PT901 1-443-283-11 TRANSFORMER, POWER (MX)
0 PT902 X-4956-322-1 SUB TRANS ASSY (EA, MX)
0 PT902 X-4956-293-1 SUB TRANS ASSY (AEP, UK)

0 PT902 X-4956-294-1 TRANS ASSY, SUB (SP, E2, E3, E51, AR, AUS)
RE701 1-477-680-12 ENCODER, ROTARY

64
HCD-RG121
MEMO
65
HCD-RG121
REVISION HISTORY
Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision

1.0 2004.04 New

Service Manual: HCD-RG121

Uploaded by

Copyright:

Available Formats

Service Manual: HCD-RG121

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: HCD-RG121

Uploaded by

Copyright:

Available Formats

HCD-RG121

SERVICE MANUAL AEP Model

• HCD-RG121 is the tuner, deck, CD and

Model Name Using Similar Mechanism New

Tape deck Model Name Using Similar Mechanism New

Amplifier section Tape deck section

Dimensions (w/h/d) incl. projecting parts and controls

Notes on chip component replacement

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

Unleaded solder 1. SERVICE POSITION ............................................... 4

7. ELECTRICAL PARTS LIST .................................. 53

• SERVICE POSITION-2 (BD80A BOARD)

Remove the CD mechanism deck and place it on top of the

List of button locations and reference pages

How to use this page Illustration number

A–O P–Z ?/1 (power) 1 (8, 16, 27, 30, 33,

A–E F–Z ?/1 (power) 1 (8, 26)

qh 7 2 Press CLOCK/TIMER SET.

qf q; 5 Press . or > repeatedly to set the

3-3.FRONT PANEL SECTION

3-4.CD MECHANISM DECK 3-5.TAPE MECHANISM DECK, 3-6.PANEL BOARD

3-11.BD80A BOARD 3-12.CONNECT BOARD 3-14.OPTICAL PICK-UP 3-15.SENSOR BOARD

3-7.BACK PANEL SECTION, 3-13.DRIVER BOARD, 3-16.MOTOR (TB) BOARD

3-17.MOTOR (LD) BOARD

3-8.POWER TRANSFORMER 3-9.MAIN BOARD

3-1. COVER (TOP)

6 two screws (Case 3 TP2)

2 screw (Case 3 TP2)

Front panel side

2 Pull-out the disc tray.

3-3. FRONT PANEL SECTION

8 wire (flat type) 7 core (CN253)

3 screw (+BVTP 3 × 10)

7 wire (flat type) 31 core (CN302)

qd front panel section

1 three screws (+BVTP 3 × 8)

3-4. CD MECHANISM DECK (CDM74-K6BD80)

1 three screws (+BVTP 3 × 10)

4 CD mechanism deck (CDM74-K6BD80)

2 connector 12p (CN701)

3-5. TAPE MECHANISM DECK, GAME JACK BOARD

6 GAME JACK board 5 two screws

4 tape mechanism deck

3-6. PANEL BOARD

3 wire (flat type) 13 core (CN602)

3-7. BACK PANEL SECTION, SUB-TRANS BOARD

9 back panel section

8 SUB-TRANS board 7 connector

3-8. POWER TRANSFORMER

3-9. MAIN BOARD

3-10. AMP BOARD

4 two screws 5 heat sink

3-11. BD80A BOARD

2 wire (flat type) 16 core (CN101)

3-12. CONNECT BOARD

1 wire (flat type) 17 core (CN201)

3-13. DRIVER BOARD, SW BOARD

2 wire (flat type) 5p (CN702)