A. Adjustable Headband.

Important Safety Information PRODUCT OVERVIEW B. Multi-Function Button -MFB (power on/off, pairing, play/pause,
These headphones have a built-in rechargeable battery. To avoid answer/end calls/reject call/last number redial).
• Always use the headphones at an appropriate volume. Prolonged any damage, do not attempt to remove the battery from the J C. Volume + (Next).
headphones. D. Volume - (Previous).
exposure to loud sounds may damage your ears.
SILKSOUND E. LED indicator
The battery (battery pack or combination) should not be exposed to
• Do not turn up the volume so high that you cannot hear sounds
excess heat. E F. Micro USB Charging port.
G. Microphone.
around you.
H. USB charging cable.
• Use caution or temporarily discontinue use in potentially hazardous Improper charging of the battery could lead to the battery exploding.
H I. 3.5 MM Audio in.
situations. If using a wall charger to charge your headphones, please ensure J. Fold for storage
G
• Do not use the headphones while riding a bicycle, or operating a
that it is a 5V/1A wall charger. Higher voltage chargers could risk
I
damage. CHARGING THE BATTERY
motor vehicle. The use of headphones may create a traffic hazard
Please turn off the headphones before charging
and is illegal in many areas.

• Exposing these headphones to open fire can be dangerous, as WARRANTY

they contain a lithium ion battery. The Paww SilkSound headphones ship with a 1-year warranty. If
• Do not disassemble the headphones, unless qualified to do so. you do encounter any issues during this time, you can initiate a F O
warranty claim by contacting us via email on support@mypaww.com
• Place out of reach of small children, as the packaging contains or through the Contact Us page on our website (https://www.mypaww.
com/pages/contact-us).
C
small parts.

CONTENTS – To charge your SilkSound headphones, plug the included

A B micro-USB cable into the SilkSound headphones (refer to F in the
– PAWW SilkSound Headphone System diagram above), and the other end to either a 5V/0.5A wall charger
Congratulations on your purchase of the Paww SILKSOUND! – Custom Designed Case or your computer’s USB port. When the battery is extremely low,
Please read the instructions and warnings carefully before use – 3.5MM Headphone Cable D the LED will flash red continuously, and a full charge can take up
to ensure safe and satisfactory enjoyment of this product. – USB Charging Cable to 2.5 hours. The LED will turn off once the product is fully charged.
– User Guide
www.mypaww.com

CHARGING LI-POLYMER BATTERY SAFELY Pairing with Bluetooth Devices Note： Last number redial Restore Factory Settings
The headphones have a non-removable lithium-polymer battery. 1.The headphones will automatically connect to the last connected
When not on a call, double press the MFB to redial the last number. With the headphones switched off and connected to a charger,
source device. If you have multiple devices stored on the
Do not try to remove the battery. Do not dispose of the headphone press and hold the MFB button until the LED flashes blue and
headphones and you would like to connect the headphones to a
in a fire, the battery may explode.
previously connected device, please open the Bluetooth function Call Transfer red three times.
on the device that you would like to connect the headphones to
Dispose of the headphone in accordance with the applicable laws
and regulations in your area for the disposal of lithium-polymer
and select SilkSound from the list of available Bluetooth devices Double press the ‘-‘ button to transfer an incoming call between your SPECIFICATIONS
to reconnect. phone and the headphones.
batteries.
2.If it takes longer than 3-minutes to complete the pairing process,
Bluetooth Version: V4.1
Non-compliance with the conditions of use of the lithium-polymer
1.Please keep your headphones and Bluetooth devices as close to the headphones will turn off automatically. Hang up the phone call and answer other
each other. Support: HSP, HFP, A2DP, AVRCP
battery may cause a fire, explosion or chemical burn.
2.With the headphones off, press and hold the MFB for approximately incoming call Transmitting Power: Class 2
Do not allow battery leakage to come into contact with eyes or 5 seconds or until the LED flashes blue once and you hear the Invoking a Digital Assistant Working Distance Range: ≤ 10m
skin. In case of contact, flush eyes or skin with plenty of water and prompt “power on”, followed by “pairing”. If you are already on a call, but would like to answer another incoming
3.At this point, the LED will flash blue and red. Frequency Range:2.402GHz-2.480GHz
seek medical advice. If connected to an Apple or Android device, you can invoke Siri or call, double press the MFB button to hang up on the current caller,
4.Navigate to the Bluetooth settings in your source device, scan for Google Now by simply pressing the ‘+’ button twice. Talk Time : > 10 Hours
and answer the new call.
Do not expose the lithium-polymer battery to a temperature higher new devices and search for SilkSound. Play Time : > 8 Hours
than 60°C (140°F). 5.Select SilkSound and wait for the pairing process to complete. Answering a Call Battery prompt Standby Time : > 140 Hours
Some older devices my ask for a code. If so, please enter 0000.
Do not disassemble, crush, short-circuit or incinerate your battery Charge Time : < 2.5 Hours
If the headphones are connected to a smartphone, and you’re Each time you turn on your SilkSound headphones, a prompt will
as it may cause fire, injury, burns, or other hazards. Pairing with Multiple Devices receiving a call on the phone, a voice prompt will read out the
announce the battery level.
number that is calling you. Short press the MFB to answer the call.
Before first use, please recharge your headphones. 1.Pair the SilkSound headphones to your first device using the steps
above. Ending a Call Play/Pause
Powering the Headphones On/Off 2.Once successfully paired, turn off the Bluetooth function on your
source device, and turn off the headphones completely (instructions Short press the MFB button to hang up a call. While listening to music, short press MFB to pause music. Press it
1. Long press MFB for 3 seconds. The LED will flash blue once the
above). again back to resume play .
earphone prompts “Power on”.
3.Follow the same procedure as above to connect the second source Rejecting a call
2. Long press MFB for 3 seconds, the LED will flash red once the device. To change songs, short press the ‘+’ or ‘-‘ buttons.
earphone prompts “Power off ”. 4.Once connected, re-enable the Bluetooth function on the first source Double press the MFB to reject an incoming call.
device and connect to SilkSound again. To increase or decrease volume, long press the ‘+’ or ‘-‘ buttons.