Lc550eun Sef1 LG

Global LCD Panel Exchange Center www.panelook.
com
LC550EUN
Product Specification
SPECIFICATION
FOR
APPROVAL
( ) Preliminary Specification
( ̻ ) Final Specification
Title 55.0” WUXGA TFT LCD
BUYER SUPPLIER LG Display Co., Ltd.
MODEL *MODEL LC550EUN

SUFFIX SEF1 (RoHS Verified)
*When you obtain standard approval,
please use the above model name without suffix
SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE
/ J.T. Kim / Team Leader
REVIEWED BY
/ D.K. Yang / Project Leader
PREPARED BY
/ S.H. Lee / Engineer
Please return 1 copy for your confirmation with TV Product Development Dept.
your signature and comments. LG Display Co., Ltd.
Ver. 0.1 0 /38
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LC550EUN
CONTENTS
Number ITEM Page

COVER 0
CONTENTS 1
RECORD OF REVISIONS 2
1 GENERAL DESCRIPTION 3
2 ABSOLUTE MAXIMUM RATINGS 4
3 ELECTRICAL SPECIFICATIONS 5
3-1 ELECTRICAL CHARACTERISTICS 5
3-2 INTERFACE CONNECTIONS 7
3-3 SIGNAL TIMING SPECIFICATIONS 9

3-4 SIGNAL TIMING WAVEFORMS 10
3-5 COLOR DATA REFERENCE 13
3-6 POWER SEQUENCE 14
4 OPTICAL SPECIFICATIONS 16
5 MECHANICAL CHARACTERISTICS 22
6 RELIABILITY 25
7 INTERNATIONAL STANDARDS 26
7-1 SAFETY 26
7-2 EMC 26
7-3 ENVIRONMENT 26
8 PACKING 27
8-1 DESIGNATION OF LOT MARK 27
8-2 PACKING FORM 27

9 PRECAUTIONS 28
9-1 MOUNTING PRECAUTIONS 28
9-2 OPERATING PRECAUTIONS 28
9-3 ELECTROSTATIC DISCHARGE CONTROL 29
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 29
9-5 STORAGE 29
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM 29
9-7 OPERATING GONDITION GUIDE 29
Ver. 0.1 1 /38
LC550EUN
RECORD OF REVISIONS
Revision No. Revision Date Page Description

0.1 Aug. 29, 2011 - Preliminary Specification (First Draft)
1.0 Nov. 28, 2011 - Final Specification
Ver. 0.1 2 /38
LC550EUN
1. General Description
The LC550EUN is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
b a c k l i g h t s y s t e m . T h e m a t r i x e mplo ys a-Si Th in Film Trans istor as the active e lem ent.
It is a transmissive display type which is operating in the normally black mode. It has a 54.64 inch diagonally
measured active display area with WUXGA resolution (1080 vertical by 1920 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 16.7Milion colors.
It has been designed to apply the 8-bit 2-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.
EPI(RGB)
LVDS EEPROM
Source Driver Circuit
2Port
SCL SDA S1 S1920
LVDS
Select LVDS 1,2 G1
Timing Controller
OPC
Enable
Option
signal
LVDS Rx + OPC + DGA TFT - LCD Panel
CN1 Integrated Control (1920 Ý RGB Ý 1080 pixels)
(51pin) Signals
[Gate In Panel]
ExtVBR-B I2C G1080
+12.0V
Power Circuit Power Signals
PWM_OUT CN2 Block

1~3 (4 pin)
Scanning Block 1
PWM_OUT
1~3 Scanning Block 2
+24.0V, GND, On/Off LED Driver
Scanning Block 3
General Features
Active Screen Size 54.64 inches(1387.80mm) diagonal
Outline Dimension 1244.6(H) ϧ 720.9(V) ϧ 9.9(B) / 23.1(D) mm (Typ.)
Pixel Pitch 0.630 mm x 0.630 mm
Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Color Depth 8bit, 16.7 Million colors
Luminance, White 360 cd/m2 (Center 1point ,Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Power Consumption Total 109.6W (Typ.) [Logic= 7.2W, LED Driver=100.1W((ExtVbr_B=100% )]
Weight 17.5Kg (Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment Hard coating(2H), Anti-glare treatment of the front polarizer (Haze < 1%)
Ver. 0.1 3 /38
LC550EUN
2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or permanent damage
to the LCD module.
Table 1. ABSOLUTE MAXIMUM RATINGS
Value
Parameter Symbol Unit Note
Min Max
LCD Circuit VLCD -0.3 +14.0 VDC
Power Input Voltage
Driver VBL -0.3 + 27.0 VDC
ON/OFF VOFF / VON -0.3 +5.5 VDC 1
Driver Control Voltage
Brightness EXTVBR-B -0.3 +4.0 VDC
T-Con Option Selection Voltage VLOGIC -0.3 +4.0 VDC
Operating Temperature TOP 0 +50 ¶C
2,3
Storage Temperature TST -20 +60 ¶C
Panel Front Temperature TSUR - +68 ¶C 4
Operating Ambient Humidity HOP 10 90 %RH
2,3
Storage Humidity HST 10 90 %RH
Note1. Ambient temperature condition (Ta = 25 r 2 ¶C )

2. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39¶C, and no condensation of water.
3. Gravity mura can be guaranteed below 40¶C condition.
4. The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68¶C with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 68୅. The range of operating temperature may be degraded in case of
improper thermal management in final product design.
90%
60
60%
50 Storage
Humidity [(%)RH]
Wet Bulb
Temperature [¶C]
40
40%
Operation
30
20
10
0
10%
-20 0 10 20 30 40 50 60 70 80
Dry Bulb Temperature [¶C]
Ver. 0.1 4 /38
LC550EUN
3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the LED
backlight and LED Driver circuit.
Table 2. ELECTRICAL CHARACTERISTICS

Value
Min Typ Max
Circuit :
Power Input Voltage VLCD 10.8 12.0 13.2 VDC
- 611 794 mA 1
Power Input Current ILCD
- 925 1202 mA 2
Power Consumption PLCD 7.3 9.49 Watt 1
Rush current IRUSH - - 5.0 A 3
5 - 100 % On Duty
ExtVBR-B
1 - 100 % 4
Brightness Adjust for Back Light
ExtVBR-B
40 50/60 80 Hz
Frequency
Pulse Duty Level High Level 2.5 - 3.6 Vdc HIGH : on duty
(PWM) Low Level 0 - 0.8 Vdc LOW : off duty
Note 1. The specified current and power consumption are under the VLCD=12.0V, Ta=25 r 2¶C, fV=60Hz
condition, and mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
4. ExtVBR-B signal have to input available duty range and sequence.
After Driver ON signal is applied, ExtVBR-B should be sustained from 5% to 100% more than 500ms.
After that, ExtVBR-B 1% and 100% is possible
For more information, please see 3-6-2. Sequence for LED Driver.
5. Ripple voltage level is recommended under ·5% of typical voltage
White : 255 Gray

Black : 0 Gray
Mosaic Pattern(8 x 6)
Ver. 0.1 5 /38
LC550EUN
Table 3. ELECTRICAL CHARACTERISTICS (Continue)
Values
Parameter Symbol Unit Notes
Min Typ Max
LED Driver :
Power Supply Input Voltage VBL 22.8 24.0 25.2 Vdc 1

Power Supply Input Current IBL - 4.17 4.55 A 1
VBL = 22.8V
Power Supply Input Current (In-Rush) In-rush - - 6.0 A ExtVBR-B = 100%
3
Power Consumption PBL - 100.1 109.3 W 1
Input Voltage for On V on 2.5 - 5.0 Vdc
Control System On/Off
Signals Off V off -0.3 0.0 0.7 Vdc
LED :
Life Time 30,000 50,000 Hrs 2
Notes :
1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 60
minutes at 25·2¶C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (ExtVBR-B : 100%), it is total power consumption.
2. The life time (MTTF) is determined as the time which luminance of the LED is 50% compared to that of initial
value at the typical LED current (ExtVBR-B :100%) on condition of continuous operating in LCM state at
25·2¶C.
3. The duration of rush current is about 200ms. This duration is applied to LED on time.
4. Even though inrush current is over the specified value, there is no problem if I2T spec of fuse is satisfied.
Ver. 0.1 6 /38
LC550EUN
3-2. Interface Connections

This LCD module employs two kinds of interface connection, 51-pin connector is used for the module
electronics and 14-pin connector is used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector(CN1): FI-R51S-HF(manufactured by JAE) or compatible
- Mating Connector : FI-R51HL(JAE) or compatible
Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION

No Symbol Description No Symbol Description
1 NC No Connection (Note 4) 27 NC No connection
2 NC No Connection (Note 4) 28 R2AN SECOND LVDS Receiver Signal (A-)
3 NC No Connection (Note 4) 29 R2AP SECOND LVDS Receiver Signal (A+)
4 NC No Connection (Note 4) 30 R2BN SECOND LVDS Receiver Signal (B-)
5 NC No Connection (Note 4) 31 R2BP SECOND LVDS Receiver Signal (B+)
6 NC No Connection (Note 4) 32 R2CN SECOND LVDS Receiver Signal (C-)
7 LVDS Select ‘H’ =JEIDA , ‘L’ or NC = VESA 33 R2CP SECOND LVDS Receiver Signal (C+)
8 ExtVBR-B External PWM (from System) 34 GND Ground
9 NC No Connection (Note 4) 35 R2CLKN SECOND LVDS Receiver Clock Signal(-)
10 OPC Enable ‘H’ = Enable , ‘L’ or NC = Disable 36 R2CLKP SECOND LVDS Receiver Clock Signal(+)
11 GND Ground 37 GND Ground
12 R1AN FIRST LVDS Receiver Signal (A-) 38 R2DN SECOND LVDS Receiver Signal (D-)
13 R1AP FIRST LVDS Receiver Signal (A+) 39 R2DP SECOND LVDS Receiver Signal (D+)
14 R1BN FIRST LVDS Receiver Signal (B-) 40 NC No connection
15 R1BP FIRST LVDS Receiver Signal (B+) 41 NC No connection
16 R1CN FIRST LVDS Receiver Signal (C-) 42 NC or GND No Connection or Ground
17 R1CP FIRST LVDS Receiver Signal (C+) 43 NC or GND No Connection or Ground
18 GND Ground 44 GND Ground (Note 6)
19 R1CLKN FIRST LVDS Receiver Clock Signal(-) 45 GND Ground
20 R1CLKP FIRST LVDS Receiver Clock Signal(+) 46 GND Ground
21 GND Ground 47 NC No connection
22 R1DN FIRST LVDS Receiver Signal (D-) 48 VLCD Power Supply +12.0V
23 R1DP FIRST LVDS Receiver Signal (D+) 49 VLCD Power Supply +12.0V
24 NC No connection 50 VLCD Power Supply +12.0V
25 NC No connection 51 VLCD Power Supply +12.0V
26 NC or GND No Connection or Ground - - -
Note
1. All GND(ground) pins should be connected together to the LCD module’s metal frame.
2. All VLCD (power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
4. #1~#6 & #9 NC (No Connection): These pins are used only for LGD (Do not connect)
5. Specific pins(pin No. #10) are used for OPC function of the LCD module.
If not used, these pins are no connection. (Please see the Appendix VI for more information.)
6. Specific pin No. #44 is used for “No signal detection” of system signal interface.
It should be GND for NSB(No Signal Black) during the system interface signal is not.
If this pin is “H”, LCD Module displays AGP(Auto Generation Pattern).
Ver. 0.1 7 /38
LC550EUN
3-2-2. Backlight Module

Master
-LED Driver Connector
: 20022WR - H14B2(Yeonho) or Compatible
- Mating Connector
: 20022HS - 14B2 or Compatible
Table 5-1. LED DRIVER CONNECTOR PIN CONFIGURATION
Pin No Symbol Description Note

1 VBL Power Supply +24.0V
6 GND Backlight Ground
8 GND Backlight Ground 1
11 Status Back Light Status 2
12 VON/OFF Backlight ON/OFF control 3
13 NC Don’t care
14 NC Don’t care
Notes :1. GND should be connected to the LCD module’s metal frame.
2. Normal : Low (under 0.7V) / Abnormal : Open
3. Each impedance of pin #12 is over 50 [K˟] .
୛ Status
୛ Rear view of LCM
PCB
1 14
1 14
…
…
<Master>
Ver. 0.1 8 /38
LC550EUN
3-3. Signal Timing Specifications

Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal
timings should be satisfied with the following specification for normal operation.
Table 6. TIMING TABLE (DE Only Mode)
ITEM Symbol Min Typ Max Unit Note
Display
tHV 960 960 960 tCLK 1920 / 2
Period
Horizontal
Blank tHB 100 140 240 tCLK 1
Total tHP 1060 1100 1200 tCLK
Display
tVV 1080 1080 1080 Lines
Period
20 45 69
Vertical Blank tVB Lines 1
(228) (270) (300)
1100 1125 1149
Total tVP Lines
(1308) (1350) (1380)
ITEM Symbol Min Typ Max Unit Note
DCLK fCLK 63.00 74.25 78.00 MHz
Horizontal fH 57.3 67.5 70 KHz 2
Frequency
2
57 60 63
Vertical fV Hz NTSC
(47) (50) (53)
(PAL)
Note: 1. The input of HSYNC & VSYNC signal does not have an effect on normal operation (DE Only Mode).
If you use spread spectrum of EMI, add some additional clock to minimum value for clock margin.
2. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate and the horizontal frequency
୔ Timing should be set based on clock frequency.
Ver. 0.1 9 /38
LC550EUN
3-4. LVDS Signal Specification

3-4-1. LVDS Input Signal Timing Diagram
0.7VDD
DE, Data
0.3VDD
tCLK
0.5 VDD
DCLK
Valid data
First data Invalid data Pixel 0,0 Pixel 2,0 Invalid data
Valid data
Second data Invalid data Pixel 1,0 Pixel 3,0 Invalid data
DE(Data Enable)
tHV
tHP
1 1080
DE(Data Enable)
tVV
tVP
Ver. 0.1 10 /38
LC550EUN
3-4-2. LVDS Input Signal Characteristics

1) DC Specification
LVDS -
LVDS +
V CM V IN _ MAX V IN _ MIN
# V CM = {( LVDS +) + ( LVDS - )} /2
0V
Description Symbol Min Max Unit Note

LVDS Common mode Voltage VCM 1.0 1.5 V -
LVDS Input Voltage Range VIN 0.7 1.8 V -
Change in common mode Voltage ȟVCM - 250 mV -
2) AC Specification
Tclk
LVDS Clock
LVDS Data
( F clk = 1 /T clk )
tSKEW tSKEW
A
Tclk
LVDS 1’st Clock 80%
LVDS 2nd / 3rd / 4th Clock

20%
tRF
tSKEW_min tSKEW_max
Description Symbol Min Max Unit Note

High Threshold VTH 100 300 mV
LVDS Differential Voltage 3
Low Threshold VTL -300 -100 mV
LVDS Clock to Data Skew tSKEW - |(0.25*Tclk)/7| ps -
LVDS Clock/DATA Rising/Falling time tRF 260 |(0.3*Tclk)/7| ps 2
Effective time of LVDS teff |·360| - ps -
LVDS Clock to Clock Skew (Even to Odd) tSKEW_EO - |1/7* Tclk| ps -
Note 1. All Input levels of LVDS signals are based on the EIA 644 Standard.
2. If tRF isn’t enough, teff should be meet the range.
3. LVDS Differential Voltage is defined within teff
Ver. 0.1 11 /38
LC550EUN
360ps
0.5tui tui
V+
data
VTH
Vcm
VTL
V-
360ps
data
teff
V+ tui : Unit Interval
clk
Vcm
V-
clk
Ver. 0.1 12 /38
LC550EUN
3-5. Color Data Reference
The brightness of each primary color(red,green,blue) is based on the 8bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 7 provides a reference for color versus data input.
Table 7. COLOR DATA REFERENCE
Input Color Data
RED GREEN BLUE

Color MSB LSB MSB LSB MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED ... ... ... ...
RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN ... ... ... ...
GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE ... ... ... ...
BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Ver. 0.1 13 /38
LC550EUN
3-6. Power Sequence

3-6-1. LCD Driving circuit
90% 90%
Power Supply For LCD
VLCD 10% 10% 10%
0V
T8
T1
T5
T2
Valid Data Vcm : LVDS Common mode Voltage
30%
Interface Signal (Tx_clock) 0V
100% T3 T4
T6
User Control Signal
(LVDS_select, OPC Enable, ExtVBR-B)
Power for LED T7 LED ON
Table 8. POWER SEQUENCE
Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - 20 ms 1
T2 0 - - ms 2
T3 200 - - ms 3
T4 200 - - ms 3
T5 1.0 - - s 4
T6 - - T2 ms 5
T7 0.5 - - s 6
T8 100 - - ms 7
1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
Note : 2. If T2 is satisfied with specification after removing LVDS Cable, there is no problem.
3. The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. T5 should be measured after the Module has been fully discharged between power off and on period.
5. If the on time of signals (Interface signal and user control signals) precedes the on time of Power (VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
6. If there is no abnormal display, no problem.
7. It is recommendation specification that T8 has to be 100ms as a minimum value.
୔ Please avoid floating state of interface signal at invalid period.
୔ When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.
Ver. 0.1 14 /38
LC550EUN
3-6-2. Sequence for LED Driver

Power Supply For LED Driver
24V (typ.)
90% 90%
VBL
10%
0V
T1 T2 T3
VON/OFF
LED ON
ExtVBR-B
T4 T6
3-6-3. Dip condition for LED Driver
T5
VBL : 24V
VBL(Typ.) x 0.8
0V
Table 9. Power Sequence for LED Driver
Values
Parameter Units Remarks
Min Typ Max
T1 20 - - ms 1
T2 500 - - ms
T3 10 - - ms
T4 0 - - ms
T5 - - 10 ms VBL(Typ) x 0.8
T6 500 - - ms 2
Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.
Even though T1 is over the specified value, there is no problem if I 2T spec of fuse is satisfied.
2. In T6 section, ExtVBR-B should be sustained from 5% to 100% .
Ver. 0.1 15 /38
LC550EUN
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25·2¶C.
The values are specified at 50cm from the LCD surface at a viewing angle of ) and T equal to 0 ¶.
FIG. 1 shows additional information concerning the measurement equipment and method.
LCD Module Pritchard 880 or

Optical Stage(x,y)
equivalent
50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method
Ta= 25·2¶C, VLCD=12.0V, fV=60Hz, Dclk=74.25MHz,
Table 10. OPTICAL CHARACTERISTICS EXTVBR-B =100%
Value
Min Typ Max
Contrast Ratio CR 1200 1600 - 1
2D 290 360 2
Surface Luminance, white LWH cd/m2
3D 110 135 7
Luminance Variation G WHITE 5P 1.35 3
Variation G to G ɍ 6 9 5
Response Time
Gray to Gray (BW) G to G BW 8 12 ms 4
Rx 0.635
RED
Ry 0.343
Gx 0.317
GREEN
Color Coordinates Gy Typ 0.600 Typ
[CIE1931] Bx -0.03 0.153 +0.03
BLUE
By 0.057
Wx 0.279
WHITE
Wy 0.292
Color Temperature 10,000 K
Color Gamut 68 %
right(I=0¶) Tr (x axis) 89 - -
2D left (I=180¶) Tl (x axis) 89 - -
Viewing degree 6
(CR>10) up (I=90¶) Tu (y axis) 89 - -
Angle
down (I=270¶) Td (y axis) 89 - -
3D Tu (y axis)
up + down 16 20 - degree 8
(CT˺10%) +Td (y axis)
Gray Scale - - - 7
Ver. 0.1 16 /38
LC550EUN
Note : 1. Contrast Ratio(CR) is defined mathematically as :
Surface Luminance with all white pixels

Contrast Ratio =
Surface Luminance with all black pixels
It is measured at center 1-point.
2. Surface luminance are determined after the unit has been ‘ON’ and 1 Hour after lighting the
backlight in a dark environment at 25·2¶C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.
3. The variation in surface luminance , G WHITE is defined as :
G WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5)
Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations .
For more information, see the FIG. 2.
4. Response time is the time required for the display to transit from any gray to white (Rise Time, TrR)
and from any gray to black (Decay time, TrD). For additional information see the FIG. 3.
୔ G to GBW Spec stands for average value of all measured points.
Photo Detector : RD-80S / Field : 2 ¶
5. G to G ɍ is Variation of Gray to Gray response time composing a picture
ȭ(Xi- u)2 Xi = Individual Data

G to G (ɍ) =
˲ N u = Data average
N : The number of Data
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 4.
7. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 11.
8. 3D performance specification is expressed by 3D luminance and 3D viewing angle.
Gray Level Luminance [%] (Typ)

L0 0.0006
L15 0.27
L31 1.04
L47 2.49
L63 4.68
L79 7.66
L95 11.5
L111 16.1
L127 21.6
L143 28.1
L159 35.4
L175 43.7
L191 53.0
L207 63.2
L223 74.5
L239 86.7
L255 100
Ver. 0.1 17 /38
LC550EUN
Measuring point for surface luminance & measuring point for luminance variation.
H
A
ྚ ྛ
ྙ
V
B
A : H / 4 mm
ྜ ྜྷ B : V / 4 mm
@ H,V : Active Area
FIG. 2 5 Points for Luminance Measure
Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Black or White”.
Tr Tf
100
90
Optical
Response
10
Gray(N) White Gray(N) Black
0
N = 0(Black)~255(White)
FIG. 3 Response Time
Ver. 0.1 18 /38
LC550EUN
Dimension of viewing angle range
Normal
E Y
I = 90 q , Up
I = 180 q , Left
T
I = 0 q , Right
I = 270 q , Down
FIG. 4 Viewing Angle
Ver. 0.1 19 /38
LC550EUN
2 7 3
LMS
LW-RW LB-RW 6 1 8
Right or left eyeglass

4 9 5 3D display ( Circular polarizer )
LW-RB LB-RB
(b) Measurement
(a) Test pattern image position (c) Setup
< FIG. 6. Measurement configuration>
Luminance
T
Lum( LE or RE, test pattern, number )
Measurement through measurement

Left or Right eyeglass position
< FIG. 7. Positioning eyeglass > < FIG. 8. notation of luminance measurement >
In order to measure 3D luminance, 3D crosstalk and 3D viewing angle, it need to be prepared as below;
1) Measurement configuration
4-Test pattern images. Refer to FIG 6.
-. LW-RW : White for left and right eye
-. LW-RB : White for left eye and Black for right eye
-. LB-RW : Black for left eye and white for right eye
-. LB-RB : Black for left eye and right eye
Image files where black and white lines are displayed on even or odd lines.
Luminance measurement system (LMS) with narrow FOV (field of view) is used. Refer to FIG 1.
2) Positioning Eyeglass (refer to appendix-VII for standard specification of eyeglass)

Find angle of minimum transmittance.
This value would be provided beforehand or measured by the following steps;
(i) Test image (LB-RW) is displayed.
(ii) Left eyeglass are placed in front of LMS and luminance is measured,
rotating right eyeglass such as FIG 7. The notation for luminance measurement is “Lum(LE, LB-RW,1)”.
(iii) Find the angle where luminance is minimum.
* Following measurements should be performed at the angle of minimum transmittance of eyeglass.
Ver. 0.1 20 /38
LC550EUN
3) Measurement of 3D luminance
(i) Test image ( LW-RW ) is displayed.
(ii) Left or right eyeglass are placed in front of LMS successively and
luminance is measured at center 1 point where the notation for luminance measurement is
“Lum(LE, LW-RW,1)” or “Lum(RE, LW-RW,1).
4) Measurement of 3D crosstalk
(i) Test image ( LB-RW, LW-RB and LB-RB ) is displayed.
(ii) Right or left eyeglass are placed in front of LMS successively and
luminance is measured for position 1.
with rotating LMS or sample vertically.
Lum(LE, LB-RW,1) - Lum(LE, LB-RB,1)

Lum(LE, LW-RB,1) - Lum(LE, LB-RB,1)
or
Lum(RE, LW-RB,1) - Lum(RE, LB-RB,1)
Lum(RE, LB-RW,1) - Lum(RE, LB-RB,1)
5) Measurement of 3D Viewing Angle

3D viewing angle is the angle at which the 3D crosstalk is under 10%. The angles are
determined for the vertical or y axis with respect to the z axis which is normal to the LCD
module surface and measured for position 1. For more information , see the Fig 9
stz
y axis
siTy~ s~Tyi
ോyu(up)
z axis stz
LCM ᇟyd (down)
stz
siTyi
(a) Test pattern image (b) Measurement of 3D viewing angle (up/down)
< FIG. 9. Measurement of 3D crosstalk and 3D viewing angle >
Ver. 0.1 21 /38
LC550EUN
5. Mechanical Characteristics
Table 12 provides general mechanical characteristics.
Table 12. MECHANICAL CHARACTERISTICS

Item Value
Horizontal 1244.6 mm
Outline Dimension Vertical 720.9 mm
Depth 9.9 mm
Bezel Area
Vertical 688.4 mm
Active Display Area
Vertical 680.4 mm
Weight 17.5 Kg (Typ.), 18.5 kg (Max.)
Note : Please refer to a mechanical drawing in terms of tolerance at the next page.
Ver. 0.1 22 /38

/36
LC550EUN
[ FRONT VIEW ]
Ver. 0.1
LC550EUN
[ REAR VIEW ]
Set : Top
Set : Down
Ver. 0.1
LC550EUN
6. Reliability
Table 13. ENVIRONMENT TEST CONDITION
No. Test Item Condition
1 High temperature storage test Ta= 60¶C 240h
2 Low temperature storage test Ta= -20¶C 240h
3 High temperature operation test Ta= 50¶C 50%RH 240h
4 Low temperature operation test Ta= 0¶C 240h
Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z,
Each direction per 10 min
Shock level : 30Grms

Shock test Waveform : half sine wave, 11ms
6
(non-operating) Direction : ᇹX, ᇹY, ᇹZ
One time each direction
7 Humidity condition Operation Ta= 40 ¶C ,90%RH
Altitude operating 0 - 15,000 ft

8
storage / shipment 0 - 40,000 ft
Note : Before and after Reliability test, LCM should be operated with normal function.
Ver. 0.1 25 /38
LC550EUN
7. International Standards
7-1. Safety
a) UL 60065, Seventh Edition, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
c) EN 60065:2002 + A11:2008, European Committee for Electrotechnical Standardization (CENELEC).
d) IEC 60065:2005 + A1:2005, The International Electrotechnical Commission (IEC).
(Including report of IEC60825-1:2001 clause 8 and clause 9)
Notes
1. Laser (LED Backlight) Information
&ODVV0/('3URGXFW
,(&
(PEHGGHG/('3RZHU&ODVV0
2. Caution
: LED inside.
Class 1M laser (LEDs) radiation when open.
Do not open while operating.
7-2. EMC
a) ANSI C63.4 “American National Standard for Methods of Measurement of Radio-Noise
Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.”
American National Standards Institute (ANSI), 2003.
b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbance
characteristics – Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.
7-3. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003
Ver. 0.1 26 /38

/36
LC550EUN
8. Packing
8-1. Information of LCM Label

a) Lot Mark
A B C D E F G H I J K L M
A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.
Note
1. YEAR
Year 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020
Mark A B C D E F G H J K
2. MONTH
Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C
b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
8-2. Packing Form

a) Package quantity in one Pallet : 16 pcs
b) Pallet Size : 1440 mm(W) X 1140 mm(D) X 950 mm(H)
Ver. 0.1 27 /38
LC550EUN
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2. Operating Precautions

(1) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(2) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer
(3) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(4) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(5) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(6) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(7) A screw which is fastened up the steels should be a machine screw.
(if not, it can causes conductive particles and deal LCM a fatal blow)
(8) Please do not set LCD on its edge.
(9) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal
display, sound noise and temperature rising.
Ver. 0.1 28 /38
LC550EUN
9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.
9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5¶C and 35¶C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
(3) Storage condition is guaranteed under packing conditions.
(4) The phase transition of Liquid Crystal in the condition of the low or high storage temperature will be
recovered when the LCD module returns to the normal condition.
9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.
9-7. Operating condition guide

(1) The LCD product should be operated under normal conditions. Normal condition is defined as below;
- Temperature : 5 ~ 40 ఁ, normal humidity
- Display pattern : continually changing pattern (Not stationary)
(2) If the product will be used in extreme conditions such as high temperature, display patterns or operation
time etc..,
It is strongly recommended to contact LGD for Qualification engineering advice. Otherwise, its reliability
and function may not be guaranteed. Extreme conditions are commonly found at Airports, Transit Stations,
Banks, Stock market, and Controlling systems. The LCD product should be applied by global standard
environment. (refer ETSI EN 300, IEC 60721)
Ver. 0.1 29 /38
LC550EUN
# APPENDIX-I
̰ Pallet Ass’y
NO. DESCRIPTION MATERIAL

1 LCD Module 55” LCD
2 BAG AL Bag
3 TAPE MASKING 20MMX50M
4 PALLET Plywood 1440X1140X125.5mm
5 PACKING,BOTTOM EPS
6 PACKING,TOP EPS
7 ANGLE,PACKING PAPER
8 BAND PP
9 ANGLE,COVER PAPER
10 BAND STEEL OR PP
11 LABEL YUPO 80G 100X70
Ver. 0.1 30 /40

/38
LC550EUN
# APPENDIX- II-1
‫ غ‬LCM Label
LC550EUN
Model (SE)(F1)
RoHS Verified
Serial No.
X X X X X X X X X X X X X X X X X
UL, TUV Mark

MADE IN KOREA
LGD Logo Origin
Ver. 0.1 31 /38
LC550EUN
# APPENDIX- II-2
‫ غ‬Pallet Label
LC550EUN
SEF1
16 PCS 001/01-01
MADE IN KOREA RoHS Verified
XXXXXXXXXXXXX XXX
Ver. 0.1 32 /38
LC550EUN
# APPENDIX- III-1
̰ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7= “L” or “NC”)
Host System THC63LVD103

24 Bit or Compatible Timing
RED0 33 Controller
RED1 34 FI-RE51S-HF
RED2 35
RED3 36
31
RED4 37 TA- 12 RO0N
30 100ȳ
RED5 38 TA+ 13 RO0P
RED6 59
RED7 61 29
TB- 14 RO1N
4 28 100ȳ
TB+ 15 RO1P
5
GREEN0 40
25
GREEN1 41 TC- 16 RO2N
GREEN2 42 24 100ȳ
TC+ 17 RO2P
GREEN3 44
GREEN4 45 23
TCLK- 19 ROCLKN
GREEN5 46 22 100ȳ
GREEN6 62 TCLK+ 20 ROCLKP
GREEN7 63
21
6 TD- 22 RO3N
8 20 100ȳ
TD+ 23 RO3P
BLUE0 48
BLUE1 49
BLUE2 50
BLUE3 52
BLUE4 53
BLUE5 54 7 VESA/ JEIDA
BLUE6 64
BLUE7 1
9
11
Hsync 55 LCM Module
GND
Vsync 57
Data Enable 58
CLOCK 12
Note: 1. The LCD module uses a 100 Ohm[ȳ] resistor between positive and negative lines of each receiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 0.1 33 /38
LC550EUN
# APPENDIX- III-2
̰ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7= “H” )
Host System THC63LVD103

24 Bit or Compatible Timing
RED0 4 Controller
RED1 5 FI-RE51S-HF
RED2 59
RED3 61
31
RED4 33 TA- 12 RO0N
30 100ȳ
RED5 34 TA+ 13 RO0P
RED6 35
RED7 36 29
TB- 14 RO1N
37 28 100ȳ
TB+ 15 RO1P
38
GREEN0 6
25
GREEN1 8 TC- 16 RO2N
GREEN2 62 24 100ȳ
TC+ 17 RO2P
GREEN3 63
GREEN4 40 23
TCLK- 19 ROCLKN
GREEN5 41 22 100ȳ
GREEN6 42 TCLK+ 20 ROCLKP
GREEN7 44
21
45 TD- 22 RO3N
46 20 100ȳ
TD+ 23 RO3P
BLUE0 9
BLUE1 11
BLUE2 64
BLUE3 1
BLUE4 48
BLUE5 49 7 VESA /JEIDA
BLUE6 50
BLUE7 52
53
54
Hsync 55 LCM Module
VCC
Vsync 57
Data Enable 58
CLOCK 12
Note :1. The LCD module uses a 100 Ohm[ȳ] resistor between positive and negative lines of each receiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 0.1 34 /38
LC550EUN
# APPENDIX- IV
‫ غ‬LVDS Data-Mapping Information (8 Bit )
1) LVDS Select : “H” Data-Mapping (JEIDA format)
RCLKP
RCLKM
RAP R13’ R12’ G12 R17 R16 R15 R14 R13 R12 G12”
RBP G14’ G13’ B13 B12 G17 G16 G15 G14 G13 B13”
RCP B15’ B14’ DE VSYNC HSYNC B17 B16 B15 B14 DE”
RDP R11’ R10’ X B11 B10 G11 G10 R11 R10 X”
2) LVDS Select : “L” Data-Mapping (VESA format)
RCLKP
RCLKM
RAP R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”
RBP G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B15”
RCP B13’ B12’ DE VSYNC HSYNC B15 B14 B13 B12 DE”
RDP R17’ R16’ X B17 B16 G17 G16 R17 R16 X”
Ver. 0.1 35 /38
LC550EUN
# APPENDIX- V-1
‫ غ‬Option Pin Circuit Block Diagram
1) Circuit Block Diagram of LVDS Format Selection pin
LVDS Select Pin : Pin 7
1K˟
LVDS Select
(Pin 7) LVDS Select
50k˟
ASIC
(TCON)
System Side LCM Side
2) Circuit Block Diagram of OPC Enable Selection pin
OPC Enable Pin : Pin 10
R1 1K˟
OPC _Enable
OPC _Enable
(Pin 10)
50k˟ ASIC
(TCON)
System Side LCM Side

R1 ˺ 1K˟
Ver. 0.1 36 /38
LC550EUN
# APPENDIX- VI
‫ غ‬Scanning and OPC Design Guide
̹ When OPC Enable is “L", OPC Output = System Dimming.

OPC Output( PWM Signal) is synchronized with V-Sync Freq. of System in T-Con Board.
(4pin)
#1 : PWM_TOUT #1
#2 : PWM_TOUT #2
#3 : PWM_TOUT #3 LCM T-con Board
#4 : GND
#1
#4
T-Con
(51pin)
#8 : Ext_PWM #1 51
#10 : OPC_EN
CNT1 51pin
CNT4
#4 #1
B/L Signal
Generation OPC On
Block 3.3V
System OPC Off

LED Main IC
Driver (PWM Generator)
14pin
Chassis
<With Driver Model>
‫ ك‬PWM Specification ( VDD = 3.3V ) @ OPC

1. PWM High Voltage Range : 2.5V~3.6V
2. PWM Low Voltage Range : 0.0V~0.8V
VDD
EXTVBR-B 50 Hz for PAL VDD*0.9
Frequency 60 Hz for NTSC
Rising Time
Rising Time MAX 10.0 Ɇs

Falling Time
VDD*0.1
Falling Time MAX 10.0 Ɇs
0
Ver. 0.1 37 /38
LC550EUN
# APPENDIX- VII
‫ غ‬Standard specification of Eyeglasses
This is recommended data of Eyeglasses for LC550EUN-SEF1 model. (details refer to table)
For each item, depending on the eyeglass manufacturer tolerances may occur, this tolerance can
affect 3D performance. (3D Crosstalk, 3D luminance, 3D viewing angle)
<Table. Standard specification of Eyeglasses>
Design item of Eyeglasses Left Right Remark
Optical a) Slow axis of retarder -45ȋ 45ȋ Refer to

axis b) Transmission axis of polarizer drawing
0ȋ 0ȋ
Retardation
Retarder 125nm @550nm
value
୔Recommended polarizer
Polarization efficiency: more than 99.90%
Retarder
Polarizer
+Ʌ/4
45 ȋ
45ȋ
-45ȋ
135
135ȋ
45 ȋ ȋ Right eye
-Ʌ/4
0ȋ 90ȋ
Left eye
Bottom Cell Top Patterned

Patterned Direction from viewer
POL POL retarder
retarder
a) Slow axis of retarder b) Transmission axis of polarizer
-45ȋ 45ȋ 0ȋ 0ȋ
Left Right Left Right
(b) Configuration of Eyeglasses
<Drawing. Information of optical axis>
Ver. 0.1 38 /38

Lc550eun Sef1 LG

Uploaded by

Copyright:

Available Formats

Lc550eun Sef1 LG

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lc550eun Sef1 LG

Uploaded by

Copyright:

Available Formats

Global LCD Panel Exchange Center www.panelook.

Title 55.0” WUXGA TFT LCD

BUYER SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LC550EUN

/ J.T. Kim / Team Leader

/ D.K. Yang / Project Leader

Ver. 0.1 0 /38

Number ITEM Page

2 ABSOLUTE MAXIMUM RATINGS 4

3-1 ELECTRICAL CHARACTERISTICS 5

3-2 INTERFACE CONNECTIONS 7

3-3 SIGNAL TIMING SPECIFICATIONS 9

3-6 POWER SEQUENCE 14

8-1 DESIGNATION OF LOT MARK 27

8-2 PACKING FORM 27

Ver. 0.1 1 /38

Revision No. Revision Date Page Description

1.0 Nov. 28, 2011 - Final Specification

Ver. 0.1 2 /38

PWM_OUT CN2 Block

Ver. 0.1 3 /38

2. Absolute Maximum Ratings

Table 1. ABSOLUTE MAXIMUM RATINGS

Note1. Ambient temperature condition (Ta = 25 r 2 ¶C )

Dry Bulb Temperature [¶C]

Ver. 0.1 4 /38

Table 2. ELECTRICAL CHARACTERISTICS

White : 255 Gray

Power Supply Input Voltage VBL 22.8 24.0 25.2 Vdc 1

Ver. 0.1 6 /38

3-2. Interface Connections

Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION

Ver. 0.1 7 /38

3-2-2. Backlight Module

Table 5-1. LED DRIVER CONNECTOR PIN CONFIGURATION

Pin No Symbol Description Note

2 VBL Power Supply +24.0V

3 VBL Power Supply +24.0V

4 VBL Power Supply +24.0V

5 VBL Power Supply +24.0V

6 GND Backlight Ground

7 GND Backlight Ground

8 GND Backlight Ground 1

9 GND Backlight Ground

10 GND Backlight Ground

11 Status Back Light Status 2

12 VON/OFF Backlight ON/OFF control 3

Ver. 0.1 8 /38

3-3. Signal Timing Specifications

Table 6. TIMING TABLE (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note

ITEM Symbol Min Typ Max Unit Note

DCLK fCLK 63.00 74.25 78.00 MHz

Horizontal fH 57.3 67.5 70 KHz 2

୔ Timing should be set based on clock frequency.

Ver. 0.1 9 /38

3-4. LVDS Signal Specification

Ver. 0.1 10 /38