Section 8 Disassembly and Assembly

SECTION 8 DISASSEMBLY AND ASSEMBLY
Group 1 Precautions 8-1

Group 2 Tightening Torque 8-4
Group 3 Pump Device 8-7
Group 4 Main Control Valve 8-30
Group 5 Swing Device 8-44
Group 6 Travel Motor 8-68
Group 7 Transmission 8-92
Group 8 Steering Valve 8-147
Group 9 Front Axle and Rear Axle 8-172
Group 10 RCV Lever 8-243
Group 11 Turning Joint 8-258
Group 12 Boom, Arm, Bucket, Dozer and Outrigger Cylinders 8-265
Group 13 Work Equipment 8-287
SECTION 8 DISASSEMBLY AND ASSEMBLY
GROUP 1 PRECAUTIONS
1. REMOVAL WORK
1) Lower the work equipment completely to the ground.
If the coolant contains antifreeze, dispose of it correctly.
2) After disconnecting hoses or tubes, cover them or fit blind plugs to prevent dirt or dust from
entering.
3) When draining oil, prepare a container of adequate size to catch the oil.
4) Confirm the match marks showing the installation position, and make match marks in the necessary
places before removal to prevent any mistake when assembling.
5) To prevent any excessive force from being applied to the wiring, always hold the connectors when
disconnecting the connectors.
6) Fit wires and hoses with tags to show their installation position to prevent any mistake when
installing.
7) Check the number and thickness of the shims, and keep in a safe place.
8) When raising components, be sure to use lifting equipment of ample strength.
9) When using forcing screws to remove any components, tighten the forcing screws alternately.
10) Before removing any unit, clean the surrounding area and fit a cover to prevent any dust or dirt from
entering after removal.
11) When removing hydraulic equipment, first release the remaining pressure inside the hydraulic tank
and the hydraulic piping.
12) If the part is not under hydraulic pressure, the following corks can be used.
Nominal Dimensions
number D d L
06 6 5 8
08 8 6.5 11
10 10 8.5 12
12 12 10 15 Taper 1/8
14 14 11.5 18
øD ød
16 16 13.5 20
18 18 15 22
20 20 17 25 L
22 22 18.5 28
24 24 20 30
27 27 22.5 34
8-1
2. INSTALL WORK
1) Tighten all bolts and nuts(Sleeve nuts) to the specified torque.
2) Install the hoses without twisting or interference.
3) Replace all gaskets, O-rings, cotter pins, and lock plates with new parts.
4) Bend the cotter pin or lock plate securely.
5) When coating with adhesive, clean the part and remove all oil and grease, then coat the threaded
portion with 2-3 drops of adhesive.
6) When coating with gasket sealant, clean the surface and remove all oil and grease, check that there
is no dirt or damage, then coat uniformly with gasket sealant.
7) Clean all parts, and correct any damage, dents, burrs, or rust.
8) Coat rotating parts and sliding parts with engine oil.
9) When press fitting parts, coat the surface with antifriction compound (LM-P).
10) After installing snap rings, check that the snap ring is fitted securely in the ring groove(Check that
the snap ring moves in the direction of rotation).
11) When connecting wiring connectors, clean the connector to remove all oil, dirt, or water, then
connect securely.
12) When using eyebolts, check that there is no deformation or deterioration, and screw them in fully.
13) When tightening split flanges, tighten uniformly in turn to prevent excessive tightening on one side.
14) When operating the hydraulic cylinders for the first time after repairing and reassembling the
hydraulic cylinders, pumps, or other hydraulic equipment or piping, always bleed the air from the
hydraulic cylinders as follows:
(1) Start the engine and run at low idling.
(2) Operate the control lever and actuate the hydraulic cylinder 4-5 times, stopping 100mm
before the end of the stroke.
(3) Next, operate the piston rod to the end of its stroke to relieve the circuit.(The air bleed valve is
actuated to bleed the air.)
(4) After completing this operation, raise the engine speed to the normal operating condition.
※ If the hydraulic cylinder has been replaced, carry out this procedure before assembling the rod to
the work equipment.
※ Carry out the same operation on machines that have been in storage for a long time after
completion of repairs.
8-2
3. COMPLETING WORK
1) If the coolant has been drained, tighten the drain valve, and add water to the specified level. Run
the engine to circulate the water through the system. Then check the water level again.
2) If the hydraulic equipment has been removed and installed again, add engine oil to the specified
level. Run the engine to circulate the oil through the system. Then check the oil level again.
3) If the piping or hydraulic equipment, such as hydraulic cylinders, pumps, or motors, have been
removed for repair, always bleed the air from the system after reassembling the parts.
4) Add the specified amount of grease(Molybdenum disulphied grease) to the work equipment related
parts.
8-3

Section 8 Disassembly and Assembly

Uploaded by

Copyright:

Available Formats

Section 8 Disassembly and Assembly

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Section 8 Disassembly and Assembly

Uploaded by

Copyright:

Available Formats

SECTION 8 DISASSEMBLY AND ASSEMBLY

Group 1 Precautions 8-1

You might also like