Product Datasheet: Interpon 610 - NW300M/25KG ANTRACITE FERRO IP610

Product Datasheet
BU Powder Coatings
Interpon 610 - NW300M/25KG ANTRACITE FERRO IP610


Product Interpon 610 is a series of polyester based powder coatings, formulated without the use of TGIC, designed
Description for the exterior environment, offering excellent light and weather resistance from a single coat finish on a
variety of substrates.
Interpon 610 powders are available in a wide range of colors in gloss, satin, matt, metallic and textured
effects and can be custom matched to the user’s requirements.
 Chemical type Polyester
Powder Properties
Particle Size Suitable for electrostatic spray
Specific gravity 1.2-1.8 g/cm³ depending on colour
Storage Dry cool conditions below 30°C
Shelf life 24 months
Sales Code M-series
(a)
Stoving schedule 15 minutes at 190°C
(object temperature) 10 minutes at 200°C
8 minutes at 210°C
a) For high reactivity powders see overleaf
Test Conditions The results shown below are based on mechanical and chemical tests which (unless otherwise indicated)
have been carried out under laboratory conditions and are given for guidance only. Actual product
performance will depend upon the circumstances under which the product is used.
Substrate Mechanical tests: Polished steel

Chemical & durability tests: Pre-treated steel
Pretreatment Zinc phosphate (or equivalent pre-treatment)
Film Thickness 60 microns
Stoving 10 minutes at 200oC (object temperature)
Mechanical Tests Adhesion ISO 2409-1992 (2mm crosshatch) GT0

Erichsen Cupping ISO1520 Pass >7mm
Hardness ISO 15184 (2000gr) Pass - no penetration to
substrate
Impact ISO 6272:1993 Pass 2.5 Joule D/R
Flexibility ISO 1519:1973 (Cylindrical Mandrel) Pass 3mm
Chemical and Salt Spray ISO7253 Pass - no corrosion creep

Durability Tests (500 hours) more than 3mm from scribe
Cyclic Humidity ISO 6720-1:1998 Pass - no blistering or loss
(1000 hours) of gloss
Distilled Water ISO 2812-2:1993 Pass - no blistering or loss
Immersion (240 hours) of gloss
Exterior Durability Excellent - no chalking, slight loss of gloss after 12 months continuous exposure
but no film breakdown or reduction in protective properties
Chemical Resistance Generally good resistance to acids, alkalis and chemical substances at normal
temperatures
Pretreatment Aluminium, steel or Zintec surfaces to be coated must be clean and free from grease. Iron phosphate and
particularly lightweight zinc phosphating (or equivalent pre-treatment )of ferrous metals improves corrosion
resistance.
Aluminium substrates may require a chromate conversion coating (or equivalent pre-treatment)
Application Interpon 610 powders can be applied by manual or automatic electrostatic spray equipment. It is
Interpon 610 - Issue 6 of 03/04/2012

Mod. AN1049 1/2
Interpon610
recommended that powder film thickness be between 60-110 microns. Unused powder can be reclaimed
using suitable equipment and recycled through the coating system. . For the metallics we suggest to avoid
any recycling of powder. For “special effect” any variation in application (tribo / corona; voltage) can bring to
differences in final finish. The actual application parameters must be adapted and adjusted depending on the
type of components and with each powder batch in order to give a finish in accordance with our color
standard.
Applications in the For marine applications, related to cycles approved RINA /MED,the thickness of the metal support must be> =
marine field 0.6mm, and the thickness of the coating film must respect the value of 80μ ± 10%
Additional Interpon 610 powders are available in bright aluminium finishes which are susceptible to scratching and finger
Information marking. Protection by use of a clear polyester top coat is recommended when the coated article is to be
subjected to physical damage or outdoor environments. Unprotected bright metallic finishes are prone to
darkening in an outdoor environment. The top coat should ideally be applied within 2 hours of the metallic
coating and gloves should be worn when handling the metallic coated articles. For further details on the use of
metallic powder coatings please contact Akzo Nobel.
Interpon 610 High Reactivity powders are also available in selected grades for use where a lower stoving
temperature or shorter curing schedule is required.
Sales code: N-Series
Stoving schedule: 15 minutes at 160C
(object temperature) 8 minutes at 180C
Shelf life: 12 months
For further details on powder properties and film performance of Interpon 610 High Reactivity please contact
Akzo Nobel.
Safety Precautions Please consult the Material Safety Datasheet (MSDS)
FOR PROFESSIONAL USE ONLY

IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our
knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the
technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does
so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules
and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we give or
any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we
have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product.
Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the
product or for any loss or damage arising out of the use of the product. All products supplied and technical advice given are subject to
our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information
contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous
development. It is the user's responsibility to verify that this data sheet is current prior to using the product.
Brand names mentioned in this data sheet are trademarks of or are licensed to Akzo Nobel
Akzo Nobel Coatings Spa – Via Silvio Pellico, 8 – 22100 Como – Italy
Tel: ++39.031.345 111 - Fax: ++39.031.345 352 - WWW.interpon.com
Interpon is a trademark of Akzo Nobel group
Interpon 610 - Issue 6 of 03/04/2012 2/2

Mod.AN1049

Product Datasheet: Interpon 610 - NW300M/25KG ANTRACITE FERRO IP610

Uploaded by

Copyright:

Available Formats

Product Datasheet: Interpon 610 - NW300M/25KG ANTRACITE FERRO IP610

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Datasheet: Interpon 610 - NW300M/25KG ANTRACITE FERRO IP610

Uploaded by

Copyright:

Available Formats

Product Datasheet

Interpon 610 - NW300M/25KG ANTRACITE FERRO IP610

Substrate Mechanical tests: Polished steel

Mechanical Tests Adhesion ISO 2409-1992 (2mm crosshatch) GT0

Chemical and Salt Spray ISO7253 Pass - no corrosion creep

Interpon 610 - Issue 6 of 03/04/2012

Safety Precautions Please consult the Material Safety Datasheet (MSDS)

FOR PROFESSIONAL USE ONLY

Interpon 610 - Issue 6 of 03/04/2012 2/2

You might also like