Product Data Sheet

Hempadur Mastic
45880

Product characteristics VOC content mixed product

5% thinning, Limit value,

Legislation Value
Description by volume phase II (2010)ª
Hempadur Mastic 45880 is a polyamide curing, high solids epoxy
paint. It forms a hard and tough coating, has good wetting properties 217 g/L 248 g/L 500 g/L
EU
and cures at low temperature. [1.81 lb/US gal] [2.07 lb/US gal] [4.17 lb/US gal]
Complies with EU Directive 2004/42/EC, The Paints Directive on the 217 g/L
limitation of volatile organic compounds: subcategory j. US (coatings) - -
[1.81 lb/US gal]

217 g/L
Recommended use US (regulatory)
[1.81 lb/US gal]
Hempadur Mastic 45880 is recommended as a self-primed, surface
tolerant paint system, or as an intermediate or a topcoat in systems 217 g/L
where low VOC and high film build are required. The product can be China
[1.81 lb/US gal]
used when extended recoating properties for polyurethane topcoats
are required. It may also be used directly on zinc silicate or spray According to specific legislation, see details in the Explanatory Notes available
metallised surfaces. The product can be used for minor repairs in at Hempel website, hempel.com or at your local Hempel website. VOC values
immersed areas. may vary with shade, please consult the Safety Data Sheet, section 9. ªEU
Directive 2004/42/CE.

Service temperature:
- Maximum, dry exposure only: 120°C [248°F]. Handling
Handle with care. Before and during use, observe safety labels on
packaging and paint containers and follow all local and national safety
Certificates / Approvals regulations. Always consult Hempel’s Safety Data Sheet for this
- EC-type examined as a low flame spread material when used as product along with the Product Data Sheet.
part of a predefined paint system. Please refer to “Declaration of
Conformity” on hempel.com for further details. For professional use only.
- Meets requirements to ISO 12944 when used as part of a
predefined paint system. Part 6 C4 High.
- Complies with US FDA and EU food regulations for contact with
liquid and dry foodstuff. Consult Hempel for details.
- Complies with the European Fire Standard EN 13501-1, fire Product data
reaction class: B-s1, d0.
Product code
Features 45880
- Versatile.
- High surface tolerance.
- Low temperature curing. Product components
Base 45889
Curing agent 95880
_______________________________
Product safety
Standard shade* / code
Flash point 25°C [77°F] Light grey 12170 **

Glossy
Semi-gloss

Volume solids
80 ± 2%

* Wide range of colours is available via Hempel’s Multi-Tint® system. Issued by Hempel A/S - March 2021
** Slight discolouration may occur. This does not affect the performance of the coating. 1/4
Product Data Sheet

Hempadur Mastic
45880

Specific gravity Roughness

1.5 kg/L [12 lb/US gal] - Surface profile Medium (G) (ISO 8503-2).

Reference dry film thickness Consult Hempel's separate Surface Preparation Guidelines for more
125 micron [4.9 mils] details.

_______________________________
Aluminium shade / code Application
Aluminium grey 19000

Mixing ratio
Gloss Base 45889 : Curing agent 95880
Please consult Hempel’s Guideline on aluminium pigmented coatings. (3 : 1 by volume)

Volume solids Stir well before use.

72 ± 2%
Thinner
Specific gravity Hempel's Thinner 08450
1.3 kg/L [11 lb/US gal]
Cleaner
Reference dry film thickness Hempel's Tool Cleaner 99610
125 micron [4.9 mils]
Pot life

Product 15°C 20°C 30°C

Surface preparation temperature [59°F] [68°F] [86°F]

Induction time 15 min 10 min 0 min

Cleanliness Pot life (spray) 90 min 60 min 30 min
- Remove oil, grease and other contaminants by suitable detergent
cleaning. Pot life (brush) 3 hours 2 hours 1 hour
- Remove salts, detergents and other contaminants by high pressure
fresh water cleaning.
Application method
New build: Thinning
- Abrasive blasting to min. Sa 2½ (ISO 8501-1) / SP 10 (SSPC). Tool Application parameters
max vol.
- Concrete: According to Hempel’s Specification.
- Remove dust, blast media and loose materials. Nozzle pressure: 250 bar [3600 psi]
Airless spray 5%
Nozzle orifice: 0.017-0.023"
Maintenance and Repair Brush/Roller 5%
- Spot abrasive blasting to min. PSa 2 (ISO 8501-2) / SP 6 (SSPC).
- Minor areas may be hand or power tool cleaned instead of abrasive If brush or roller application is used, more coats will be necessary to achieve
blasting. the specified dry film thickness. Spray data are indicative and subject to
- Water jetting to min. Wa 2 (ISO 8501-4). adjustment. Pressure is for a material temperature of 20°C [68°F].
- Flash rust degree of maximum FR M (ISO 8501-4).
- Remove dust, blast media and loose materials.

Issued by Hempel A/S - March 2021

2/4
Product Data Sheet

Hempadur Mastic
45880

Film thickness Overcoating

Hempel’s specification supersedes any guidelines indicated in the overcoating
Specification range Low High Recommended table
100 micron 200 micron 125 micron
Dry film thickness 0°C 20°C 30°C 40°C
[3.9 mils] [7.9 mils] [4.9 mils] Quality name
[32°F] [68°F] [86°F] [104°F]
125 micron 250 micron 150 micron
Wet film thickness Atmospheric medium
[5 mils] [10 mils] [6 mils]

8 m²/L 4 m²/L 6.4 m²/L Hempadur Mastic Min 54 h 6h 4½ h 3½ h

Theoretical spreading 45880 Max Ext Ext Ext Ext
[330 sq ft/US [160 sq ft/US [260 sq ft/US
rate
gal] gal] gal] Hempathane HS Min 54 h 6h 4½ h 3½ h
Product may be specified in another film thickness than indicated depending 55610 Max Ext Ext Ext Ext
on purpose and area of use. This will alter spreading rate, drying and curing Atmospheric severe
time and overcoating interval. For best performance, avoid excessive film
thickness. Hempadur Mastic Min 4d 10 h 7½ h 5½ h
45880 Max Ext Ext Ext Ext

Application conditions Hempathane HS Min 4d 10 h 7½ h 5½ h

- Temperature of product must be above 15°C [59°F] during 55610 Max 27 d 72 h 54 h 40 h
application.
- To avoid condensation, apply on a clean and dry surface with a Overcoating times are indicative for products of the same generic chemistry.
temperature that is at least 3°C [5°F] above the dew point. Consult Hempel’s specification for more information.
- Surface temperature must be above -5°C [23°F] during application
and curing. Drying conditions
- To obtain the drying time stated, it is important to maintain sufficient
Relative Humidity: ventilation during application, drying and curing.
- Relative humidity must be below 85% during curing.
Overcoating details
- If the maximum overcoating interval is exceeded, roughening of the
surface is necessary to ensure intercoat adhesion.
Drying and overcoating - The surface must be dry and clean prior to application.

Other remarks
Product compatibility
- Epoxy coats have an inherent tendency of chalking in outdoor
- Previous coat: None or according to Hempel’s specification.
exposure. This does not affect the performance of the coating.
- Subsequent coat: None or according to Hempel’s specification. - Hempel’s Specification supersedes any recommendations given in
the Product Data Sheets.

Drying time

-5°C 0°C 20°C 40°C

Surface temperature
[23°F] [32°F] [68°F] [104°F]

Surface dry hours 36 20 2½ 1

Hard dry hours 48 25 3½ 1½

Fully cured days 75 30 7 3

Determined for dry film thickness 125 micron [4.9 mils] at standard conditions,
see Hempel’s Explanatory Notes for details.

Issued by Hempel A/S - March 2021

3/4
Product Data Sheet

Hempadur Mastic
45880

Storage
Shelf life

25°C 35°C
Ambient temperature
[77°F] [95°F]

Base 36 months 24 months

Curing agent 36 months 24 months

Shelf life from date of production, when stored in original, unopened

containers. Thereafter, the product quality must be re-inspected. Always check
the best before date or expiry date on the label.

Storage conditions
- Product must be stored according to local legislation, at maximum
40°C [104°F], without direct sunlight and protected from rain and
snow.

Additional documents
Additional information is available at the Hempel website hempel.com
or at your local Hempel website:
- Explanatory Notes explaining the fields in this Product Data Sheet.
- Surface Preparation Guidelines.
- Application Guidelines for different application methods.
- General Application Guidelines

This Product Data Sheet (“PDS”) relates to the supplied product (“Product”) and is subject to updating from time-to-time. Accordingly, the buyer/applicator should have regard to the PDS supplied together
with the relevant batch of the Product (and not an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the following specifications, statements and/or guidelines as listed
below or as are available from the Hempel website under ‘Products’ at www.hempel.com (the “Additional documents”):
No. Document description Location/comments
1. Technical Statement One-off specific advice provided on request for specific projects
2. Specification Only issued for specific projects
3. PDS This document
4. Explanatory Notes to the PDS Available at www.hempel.com and contain relevant information about the Product testing parameters
5. Application Instruction Where available, at www.hempel.com
6. Generic technical guidelines (e.g. on application and surface preparation) Where available, at www.hempel.com

In the event of a conflict of information between the PDS and the Additional documents, the order of priority of information shall be in the order as set out above. In such event you should also contact your
representative at Hempel for clarification. Furthermore, the buyer/applicator must have full regard to the relevant Safety Data Sheet provided with each Product and which can also be downloaded from
www.hempel.com.
Hempel shall not be liable for defects where the application of the Product has not been made fully in accordance with the recommendations and requirements set out in the relevant PDS and the Additional
Documents. The information and terms of this disclaimer apply to this PDS, the Additional documents and any other documents supplied by Hempel in respect of the Product. In addition, the Product is
supplied and all technical assistance is given subject to Hempel’s General Conditions of Sale, Delivery and Service, unless otherwise expressly agreed in writing.

hempel.com Issued by Hempel A/S - March 2021

4/4