Product Bulletin

Ultracote
Ultracote ULTRACOTE 6314 HT
(High Temperature Resistant Coating)

(Paints & Coatings)

Coatings) HEAVY DUTY, HIGH PERFORMANCE

GENERIC CLASS: Modified silicone. TOPCOAT: None required.

PRODUCT DESCRIPTION: A sophisticated COMPATIBILITY WITH OTHER COATINGS:

modified silicone as protective coating for medium to Self-priming. May be applied over inorganic zinc
high temperature service with good resistance to primers. Consult Ultracote Technical Service for
various chemical fume environments. It exhibits a specific recommendations.
property that is very resistant to thermal shock
conditions from 32oF (0oC) to 800oF (427oC) when NOTE: A mist coat may be required over inorganic
fully cured. It is self-priming and requires no primers zinc to minimize bubbling.
in most conditions.
CALCULATED VOLUME SOLIDS:
TYPICAL USES: For protection of structures, Ultracote 6314 HT 30%±2%
equipment such as stacks, furnace exteriors, steel
mufflers, exhaust manifolds, steam generating lines, RECOMMENDED DRY FILM THICKNESS
incinerators and heat exchangers operating from PER COAT: 1.5 mils (37.50 microns)
800oF (427oC) to 1000oF (538oC). The principal use
of Ultracote 6314 HT is in problem areas that require NOTE: Excessive thickness may cause blistering.
an extremely high temperature resistant coating for
protection. CALCULATED COVERAGE PER GALLON:
481 sq. ft. per mil (11.81 sq. m./li. @ 25 microns)
LIMITATIONS: Not recommended for immersion 321 sq. ft. @ 1.5 mils (7.88 sq. m./li. @ 37.5 microns)
service. acids, alkalies and other
NOTE: Assume loss factor when estimating job
CHEMICAL RESISTANCE GUIDE: requirements at prevailing condition.
Splash &
Exposure Spillage Fumes SHELF LIFE: 12 months minimum. Material on
Acids Good Excellent stock should be turned upside down every 3-4
Alkalies Fair Excellent months.
Solvents Poor Good
Salts Good Excellent COMPONENT: One
Water Excellent Excellent
FINISH: Low Gloss, Brilliant
TEMPERATURE RESISTANCE: (Dry Basis)
Sustained : 800oF (427oC) COLORS: Aluminum, Black, Red, White & Orange
Intermittent : 1000oF (538oC)
FLASH POINT: (Pensky-Martens Closed Cup)
FLEXIBILITY: Good Ultracote 6314 HT 68oF (20oC)
Ultracote Thinner #10 77oF (25oC)
ABRASION RESISTANCE: Fair
SURFACE PREPARATION: No more surface
WEATHERING: Excellent preparation than can be coated in the same working
day should be performed. Repair and fill all cavities
SUBSTRATES: Apply to properly prepared steel or and voids. Round off all sharp edges and rough
over inorganic zincs. welds.

This supersedes all previous publications. Always consult your Ultracote representative for latest product information and requirement.
 Ultracote 6314 HT, Page 2

SURFACE PREPARATION: (Cont.) All burrs THINNER: Thinning normally not required. If
and weld spatter should be completely removed oil, needed, thin up to 5% by volume with Ultracote
grease and heavy deposits of surface contaminants Thinner #10.
should be removed by use of Ultracote Thinner #2 or
toluol. All surfaces must be cleaned, dry and free of APPLICATION TEMPERATURES:
any dirty, dust, chalk, grease, oils, salts, curing Materials : 40-100oF (4-38oC)
compounds, release agents, preservatives and other Surfaces : 40-180oF (4-82oC)
deleterious materials before application is performed. Ambient : 0-130oF (-18-54oC)
Humidity : 0-95%
STEEL: It is recommended for the initial
application that metal surfaces be prepared in NOTE: Do not apply coating when the surface
accordance with SSPC-SP-10 to a degree of temperature is less than 5oF (2oC) above the dew
cleanliness in accordance to NACE#2 to obtain 1-2 point. Special thinning and application techniques
mils (25-50 microns) blast profile. may be required above or below normal conditions.

ACCEPTABLE: Dry abrasive blast to a commercial SPRAY TECHNIQUE: Use sufficient air for
grade finish in accordance to SSPC-SP-6 to a degree correct operation. Use a 50% overlap with each pass
of cleanliness in accordance to NACE#3 to obtain a of the gun. On irregular surfaces, coat the edges first,
blast profile of 1-2 mils (25-50 microns). making an extra pass later.

SPOT REPAIR: It is recommended for spot repairs SPRAY EQUIPMENT RECOMMENDED: The
that metal surfaces be prepared in accordance to following equipment has been found suitable,
SSPC-SP-6, but if this is not possible, then metal however, equivalent equipment may be substituted.
surfaces may be prepared in accordance with SSPC-
SP-3 (Power tool cleaning) and SSPC-SP-2 (Hand CONVENTIONAL: Use 3/8" minimum I.D.
tool cleaning). material hose. Hold gun approximately 12-14 inches
from the surface and at right angle to the surface.
ALLOY STEEL AND NON-FERROUS
METALS: Chemically clean surfaces in accordance Mfr. & Gun Fluid Tip Air Cap
with SSPC-SP-1 (Solvent cleaning). Abrasive Binks #18 or #62 63B 63PB
"brush" blast to provide a lightly profiled surface. DeVilbiss PMBC or JGA FX 704

NOTE: Different surface preparation procedures AIRLESS SPRAY: Use 3/8" minimum I.D.
may also be completely satisfactory for use with this material hose. Hold gun approximately 18-20 inches
product. If for any reason, additional information or from the surface and at a right angle to the surface.
explanations are needed, contact Ultracote Technical
Service before proceeding. Mfr. & Gun Pump
DeVilbiss JGB-507 QFA-159
WELDING: Welding should precede coating. In Graco 205-591 President 30:1 or
the event welding or flame cutting is performed on Bulldog 30:1
metal already coated with this product, do so in Binks Model 500 Mercury 5C
accordance with the latest instructions in USA Use a 0.013" - 0.015" tip with 2,200 psi.
Standard Z49:1 "Safety in Welding and Cutting". All
welded, burned or otherwise damage areas should be CLEAN-UP: Do not allow material to stand in
cleaned to base metal, prepared and recoated as equipment after use. Clean immediately with
specified. Ultracote Thinner #2 or xylol.

MIXING: Mix to smooth consistency with BRUSH OR ROLLER: Spray application is

mechanical agitator, making sure no pigments remain recommended. If spray application is impractical,
on the bottom of the can. use a natural bristle brush applying full strokes. Do
not over brush.
 Ultracote 6314 HT, Page 3

DRYING TIME: NOTE: Applied coating will remain soft until curing
o o
To Touch : 2 hrs. @ 90 F (32 C) 3 hrs. temperature is attained.
@ 75oF (24oC)
To Recoat : 4 hrs. @ 90oF (32oC) 6 hrs. @ STORAGE CONDITION:
75oF(24oC) Temperature : 40oF (4oC) to 110oF (43oC)
Final Cure : To obtain optimum properties, Humidity : 0-100%
coating can be cured in service temperature of 350oF
(177oC) to 450oF (232oC). Allow initial increase in PACKAGING: Gallon (3.785 liters)
temperature to proceed slowly up to 350oF (177oC) Pail (4 & 5 Gallons)
over a six-hour time period.

SAFETY INFORMATION: This product (and any recommended thinners) contains solvents and/or other chemical ingredients. Adequate health and safety precautions
should be observed during storage, handling, application and curing. Keep away from sparks, heat and open flame and use necessary safety equipment such as air
mask, non-sparking tools and ladders, etc. When working in tanks, rooms and other enclosed spaces, adequate ventilation must be provided. Keep out of reach of
children.

WARRANTY & LIMITATION OF SELLER'S LIABILITY: Ultracote Paints and Coatings Corporation, warrants only its paints represented herein meet the formulation
standards of Ultracote Paints and Coatings Corporation.

THE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF.

The buyer's sole and exclusive remedy against Ultracote Paints and Coatings Corporation shall be for replacement of the product or refund of the purchase price in the
event that a defective condition of the product should be found to exist. NO OTHER REMEDY (INCLUDING BUT NOT LIMITED TO, INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL
LOSS) SHALL BE AVAILABLE TO THE BUYER. The sole purpose of this exclusive remedy shall be to provide buyer with replacement of the product or refund of the
purchase price of the product if any defect in materials is found to exist. This exclusive remedy shall not be deemed to have failed its essential purpose so long as
Ultracote Paints and Coatings Corporation is willing and able to replace the defective materials or refund the purchase price.

Technical and application information herein is provided for the purpose of establishing a general profile of the coating and proper coating application procedures. Test
performance results were obtained in a controlled environment and Ultracote Company makes no claim that these tests or any other tests, accurately represent all
environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection and use of the coating.

ULTRACOTE PAINTS & COATINGS CORPORATION

Main Office: No. 114 Eagle St. corner F. Legaspi St., Brgy. Ugong, Pasig City, Philippines
Tel. Nos. +63 2 671-3409 / 671-9261; Telefax Nos. +63 2 671-3410 / 671-3414
Cebu Office: Rm. 307 N & N Cortes Arcade, AC Cortes Avenue, Mandaue City, Philippines
Tel. No. +63 32 344-0268; Telefax No. +63 32 344-1638
E-mail: contact@ultracote.net | Website: http://www.ultracote.net