Scania DC16 XPI Service & Operator Manual - EN

Important information
Serious risk of injury

When working on the engine, for example when adjusting drive belts and the clutch, or when changing the
oil, it is important not to start the engine. The engine could be damaged, but more importantly there is a
serious risk of injury.
For this reason, always secure the starting device or disconnect a battery cable before working on the engine.
This is especially important if the engine has a remote starter or automatic starting.
WARNING!
This warning symbol and text can be found next to those maintenance items where it is particularly impor-
tant to bear in mind the risk of injury.
Operator's manual
DC16
XPI
Industrial engine
en-GB 2 428 293
Issue 4.0
IMPORTANT!
The owner is responsible for making sure that maintenance is carried out on time and in accordance with
the instructions.
The owner must entrust the maintenance, renewal and repair of emission-related components and systems
to a qualified workshop or person.
Start-up Report – Warranty
The warranty starts when the start-up report has been filled in and sent to Scania. The normal warranty pe-
riod is 1 year, but other conditions can apply.
Fill in the particulars in the start-up report below as well. This can make things easier if you need to contact
a workshop, for example.
Engine serial number

Date of entry into service
User's name and address
Signature
Engine type
Variant
Engine type and variant are indicated on the engine data plate.
OPM 300 en-GB 2

© Scania CV AB 2015, Sweden
Start-up Report – Warranty . . . . . . . . . . . . . . . 2 Checking fuel level . . . . . . . . . . . . . . . . . . . .56
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Renewing the fuel filter using a bleeding tool57
Environment and safety . . . . . . . . . . . . . . . . . . 5 Bleeding the fuel system using a bleeding tool .
Environmental responsibility . . . . . . . . . . . . . 5 62
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . .63
Warnings and advisories . . . . . . . . . . . . . . . . . 6 Checking the drive belt . . . . . . . . . . . . . . . . .63
Certification . . . . . . . . . . . . . . . . . . . . . . . . . 11 Checking for leaks . . . . . . . . . . . . . . . . . . . . .64
Scania engines engine warranty for industrial Checking and adjusting the valve clearance .65
engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Renewing the reductant filter . . . . . . . . . . . . .68
Emission control systems warranty. . . . . . . . 12 Cleaning the reductant tank filler filter . . . . .70
Emission control system warranty statement 12 Cleaning the reductant tank ventilation filter.70
California emission control warranty statement Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
16 Composition of the fuel . . . . . . . . . . . . . . . . .71
Your warranty rights and obligations . . . . . . 16 Sulphur content of fuel. . . . . . . . . . . . . . . . . .71
Manufacturer's warranty coverage . . . . . . . . 16 Temperature dependency of the fuel . . . . . . .73
Owner's warranty responsibilities . . . . . . . . . 16 Biodiesel (FAME) . . . . . . . . . . . . . . . . . . . . .73
SCR catalytic converter . . . . . . . . . . . . . . . . . 17 Use of fuel oil in stand-by generator sets. . . .73
Engine data plate . . . . . . . . . . . . . . . . . . . . . . . 19 Reductant for SCR . . . . . . . . . . . . . . . . . . . . . .74
Component identification . . . . . . . . . . . . . . . . 20 Responsibility and quality requirements . . . .74
SCR system . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Starting and running . . . . . . . . . . . . . . . . . . . . 23 Preparing the engine for storage . . . . . . . . . . .75
Checks before running . . . . . . . . . . . . . . . . . 23 Handling the engine . . . . . . . . . . . . . . . . . . . .75
Reductant pump . . . . . . . . . . . . . . . . . . . . . . 24 Preservative coolant . . . . . . . . . . . . . . . . . . . .75
Starting the engine . . . . . . . . . . . . . . . . . . . . 25 Preservative fuel. . . . . . . . . . . . . . . . . . . . . . .75
Running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Preservative oil. . . . . . . . . . . . . . . . . . . . . . . .76
Engine shutdown. . . . . . . . . . . . . . . . . . . . . . 30 Preparations for storage . . . . . . . . . . . . . . . . .76
Checks after running . . . . . . . . . . . . . . . . . . . 31 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . .78
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 General data . . . . . . . . . . . . . . . . . . . . . . . . . .78
Engines with few hours of operation . . . . . . 33 Lubrication system . . . . . . . . . . . . . . . . . . . . .78
Cleaning the engine. . . . . . . . . . . . . . . . . . . . 33 Injection system . . . . . . . . . . . . . . . . . . . . . . .79
Maintenance intervals . . . . . . . . . . . . . . . . . . 34 Cooling system. . . . . . . . . . . . . . . . . . . . . . . .79
Lubrication system . . . . . . . . . . . . . . . . . . . . . 35 Intake system . . . . . . . . . . . . . . . . . . . . . . . . .79
Oil grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Electrical system . . . . . . . . . . . . . . . . . . . . . .79
Oil analysis . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Scania Assistance . . . . . . . . . . . . . . . . . . . . . . .80
Checking oil level . . . . . . . . . . . . . . . . . . . . . 36
Changing the oil . . . . . . . . . . . . . . . . . . . . . . 37
Labels for top-up engine oil grade . . . . . . . . 38
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cleaning the centrifugal oil cleaner . . . . . . . 39
Operational testing . . . . . . . . . . . . . . . . . . . . 44
Renewing the oil filter. . . . . . . . . . . . . . . . . . 45
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . 46
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Checking coolant level . . . . . . . . . . . . . . . . . 49
Checking antifreeze and corrosion inhibitor . 49
Antifreeze and corrosion inhibitor . . . . . . . . 50
Changing coolant . . . . . . . . . . . . . . . . . . . . . 51
Cleaning the cooling system . . . . . . . . . . . . . 52
Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Reading the vacuum indicator. . . . . . . . . . . . 54
Renewing the filter element . . . . . . . . . . . . . 54
Renewing the safety cartridge. . . . . . . . . . . . 55
Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
OPM 300 en-GB 3

Introduction
Introduction
This Operator's manual describes the operation
and maintenance of Scania industrial engines.
The engines are direct-injection, liquid-cooled,
four-stroke, turbocharged diesel engines. Certain
engines are also equipped with an SCR system
for emission control.
The engines are available with different output
and engine speed settings. Engine power for the
engine ordered is indicated on a plate located on
the engine control unit.
Note:
Only standard components are described in the
operator's manual. Information about special
equipment is contained in instructions from the
various manufacturers.
To ensure the maximum performance and the

longest service life for the engine remember the
following:
• Read through the Operator's manual before
starting to use the engine. Even regular users
of Scania engines will get new information
from the Operator's manual.
• Always follow the maintenance instructions.
• Read the section on safety carefully.
• Get to know your engine so that you know
what it can do and how it works.
• Always contact a workshop with qualified
personnel for maintenance and repair.
The information in this manual was correct at the

time of going to press. Scania reserves the right
to make alterations without prior notice.
OPM 300 en-GB 4

Environment and safety
Environment and safety Different types of advisory

Warning!
Environmental responsibility All advisories preceded by Warning! are very
Scania develops and produces engines that are as important. They warn of serious faults and incor-
environmentally-friendly as possible. Scania has rect operation that could lead to personal injury.
made major investments in the reduction of Example:
harmful exhaust emissions in order to fulfil the
environmental requirements in force in almost
every market. WARNING!
At the same time, we have been able to maintain Block the starting device when working on the
a high level of performance and operating econ- engine. If the engine starts unexpectedly, there is
omy for Scania Industrial and Marine Engines. a serious risk of injury.
To maintain these throughout the entire service
life of the engine, it is important for the user to
follow the instructions on running, maintenance
and fuel and lubricating oil as outlined in the Op-
erator's manual. Important!
Other green initiatives taken include ensuring Advisories preceded by Important! warn of
that, following maintenance and repair, waste faults and incorrect operation that could lead to
that is harmful to the environment (for example equipment being damaged. Example:
oil, fuel, coolant, filters and batteries) is disposed
of accordance with the applicable environmental IMPORTANT!
requirements.
For Scania to guarantee that the engine corre-
sponds to its certified configuration, and take re-
Safety sponsibility for any damage and injuries that
occur, maintenance must be carried out as above.
The following pages contain a summary of the
safety precautions to be complied with when op-
erating and maintaining Scania engines. The
equivalent text can also be found under the rele-
vant maintenance item.
To prevent damage to the engine and to ensure
that it runs optimally, follow the instructions in
the warnings and advisories.
If the instructions are not followed, the warranty
can cease to apply.
OPM 300 en-GB 5

Note: Safety precautions for running the

Advisories preceded by Note: refer to informa- engine
tion important to ensure the best possible opera- Daily maintenance
tion and functionality. Example:
Always carry out a visual inspection of the en-
Note: gine and engine compartment before starting the
Leave the engine off for at least 1 minute before engine or when the engine has been switched off
checking the oil level. after operation.
This inspection should be done to detect fuel, oil
or coolant leaks, or anything else that may re-
quire corrective action.
Environment
This Operator’s manual contains specially high-
lighted text with instructions to help protect the Fuel
environment during maintenance. Example: Use only fuel recommended in the Workshop
Manual.
Environment
WARNING!
Use a container to avoid spillage.
The wrong fuel grade can cause breakdowns or
stoppages by causing the injection system to
malfunction. This can cause damage to the en-
gine and, possibly, personal injury.
Warnings and advisories
Smoking
Refuelling
WARNING!
Never overfill the fuel tank as the fuel needs
Smoking is prohibited space to expand. Also ensure that the filler cap is
properly closed.
• in the vicinity of flammable or explosive ma-
terial, e.g. fuel, oils, batteries, chemicals
WARNING!
• when refuelling and in the vicinity of the fill-
ing station
During refuelling there is a risk of fire and explo-
• when working on the fuel system sion. The engine must be switched off and smok-
ing is prohibited.
OPM 300 en-GB 6

Hazardous gases Running
WARNING! WARNING!
Only start the engine in a well ventilated area. The engine must not be run in environments
The exhaust gases contain carbon monoxide and where there is a risk of explosion, as all of the
nitrogen oxides, which are toxic. electrical or mechanical components can gener-
ate sparks.
If it is run in an enclosed space, there should be
an effective device to extract exhaust gases and Approaching a running engine always poses a
crankcase gases. safety risk. Parts of the body, clothes or dropped
tools can get caught in rotating parts such as the
fan and cause injury. For personal safety all ro-
tating parts and hot surfaces must be fitted with
guards.
Starter lock
IMPORTANT!
If the control panel is not fitted with a starter Safety precautions for handling ma-
terials
lock, the engine compartment should be locked
to prevent unauthorised personnel from starting Fuel and lubricating oil
the engine. Alternatively, a lockable master
switch or battery master switch can be used.
WARNING!
All fuels and lubricants as well as many chemi-

cals are flammable. Always follow the instruc-
Starter gas tions on the relevant packaging.
The work must be carried out on a cold engine.
WARNING!
Fuel leaks and spillage on hot surfaces can cause
fire.
Never use starter gas or similar agents to help
start the engine. This can cause an explosion in Store used rags and other flammable materials
the intake manifold and possible injury. safely so as to avoid spontaneous combustion.
OPM 300 en-GB 7

Batteries Reductant
WARNING! WARNING!
The batteries contain and form oxyhydrogen gas, Reductant (AdBlue/DEF) is used in the reductant
particularly during charging. Oxyhydrogen gas tank on engines equipped with an SCR system.
is flammable and highly explosive. Avoid contact with the skin.
There must be no smoking, naked flames or If reductant comes in contact with the skin: Wash
sparks near the batteries or the battery compart- with soap and plenty of water. If reductant
ment. Incorrect connection of a battery cable or splashes in the eyes: Rinse immediately with
jump lead can cause a spark, which can cause the plenty of water. Contact a doctor if it is ingested
battery to explode. or causes skin irritations.
Chemicals Safety precautions for maintenance

and repair
WARNING! Switch off the engine
Always switch off the engine before carrying out
Most chemicals such as glycol, anti-corrosive
maintenance and repairs, unless otherwise indi-
agents, preservative oils and degreasing agents,
cated.
are hazardous to health.
Make it impossible to start the engine: Remove
Some chemicals, such as preservative oil, are
any starter key, or cut the power using the main
also flammable.
power switch or battery master switch and lock
Always follow the safety precautions on the rel- them.
evant packaging.
Fix a warning plate somewhere appropriate,
Store chemicals and other materials which are showing that work is being carried out on the en-
hazardous to health in approved containers, gine.
marking them clearly and storing them where
they are inaccessible to unauthorised persons.
WARNING!
Working with a running engine always poses a

Environment safety risk. Parts of the body, clothes or dropped
tools can get caught in rotating parts and cause
Always hand in leftover and used chemicals to injury.
an authorised waste disposal contractor.
OPM 300 en-GB 8

Hot surfaces and fluids Batteries
WARNING! WARNING!
There is always a risk of sustaining burns when The batteries contain highly corrosive sulphuric
an engine is hot. Particularly hot parts are ex- acid. Take care to protect your eyes, skin and
haust manifolds, turbochargers, oil sumps, hot clothes when charging or handling batteries.
coolant and oil in pipes and hoses. Wear protective gloves and goggles.
If sulphuric acid comes in contact with the skin:
Wash with soap and plenty of water. If it gets in
your eyes: Rinse immediately with plenty of wa-
Lifting the engine ter and seek medical attention.
Always use the engine lifting eyes. Always
check that lifting accessories are in good condi-
tion and are designed to lift the weight. Environment
Optional equipment on the engine can change
the centre of gravity. This means that it may be Always hand in used batteries to an authorised
necessary to use additional lifting devices to bal- waste disposal contractor.
ance the engine correctly and lift it safely.
WARNING!
Electrical system
Never work underneath a suspended engine! The engine must be switched off and the power
disconnected using the master switch or battery
master switch before working on the electrical
system. External power supplies to extra equip-
ment on the engine must also be disconnected.
IMPORTANT!
Scania recommends that Scania spare parts are

used for the fuel and electrical systems. Scania
spare parts are designed to minimise the risk of
fire and explosion.
OPM 300 en-GB 9

Electric welding Cooling system
IMPORTANT! WARNING!
When carrying out welding work on and near the Never open the coolant filler cap when the en-
engine, disconnect the battery and alternator gine is hot. Hot coolant and steam may spray out
leads. Pull out the multi-pin connector for the en- and cause burns.
gine control unit as well.
If the cap has to be opened do it slowly and care-
Connect the welding clamp close to the compo- fully to release the pressure before removing the
nent to be welded. The welding clamp must not cap. Wear gloves as the coolant is still very hot.
be connected to the engine, or so that the current
can cross a bearing.
When welding is finished: Environment
1. Connect the alternator and control unit ca-
bles first. Always hand in used coolant to an authorised
waste disposal contractor.
2. Then connect the batteries.
Fuel system
Lubrication system
WARNING!
WARNING!
Always wear protective goggles when testing in-
Hot oil can cause burns and skin irritation. Wear jectors. Fuel escaping at high pressure can pene-
protective gloves and goggles when changing trate tissues and cause serious injury.
hot oil.
Scania recommends that Scania spare parts are
Make sure that there is no pressure in the lubri- used for the fuel and electrical systems. Scania
cation system before starting work on it. spare parts are designed to minimise the risk of
The oil filler cap must always be in place when fire and explosion.
starting and running the engine to prevent oil be-
ing ejected.
Environment
Always hand in used oil to an authorised waste

disposal contractor.
OPM 300 en-GB 10

Before starting Certification

Ensure that all guards are in place before starting An emissions certified engine fulfils the emis-
the engine. Ensure that no tools or other objects sions requirements for a particular range of ap-
have been left on the engine. plication.
On each emissions certified engine there is a la-
WARNING! bel which shows which requirements the engine
fulfils. Scania guarantees that each such engine
The air filter must be fitted before starting the en- fulfils the emissions requirements for the range
gine. Otherwise there is a risk of objects being of application for which it is certified.
sucked into the compressor impeller or of injury
if you come into contact with the air filter. The following are required for the certified en-
gine to fulfil the emissions requirements once it
has been taken into service:
• Maintenance is to be carried out in accord-
ance with the instructions in this Operator's
manual.
• The maintenance and repair of injection
equipment are to be carried out by a qualified
workshop or person.
• The engine may only be modified with equip-
ment that has been approved by Scania.
• Seals may be broken and setting data edited
only once approval has been granted by Sca-
nia. Modifications may be made by author-
ised personnel only.
• Modifications affecting the exhaust and in-
take systems must be approved by Scania.
Otherwise, the instructions in the Operator's

manual for the running and maintenance of the
engine shall apply. The safety precautions
should be observed.
IMPORTANT!
For Scania to guarantee that the engine corre-

sponds to its certified configuration, and take re-
sponsibility for any damage and injuries that
occur, maintenance must be carried out as above.
OPM 300 en-GB 11

Scania engines engine warranty for industrial engines
Scania engines engine war- in the engine manufacturer's application for

ranty for industrial engines
certification.
Where a warrantable condition exists, Scania

Emission control systems will repair your heavy-duty off-road engine at no
cost to You including diagnosis, parts, and labor.
warranty
IMPORTANT!
Warranty period
Only applicable to engines used in the U.S.A. This warranty shall apply for one of the follow-
ing periods, whichever occurs first:
• 3,000 hours of operation as determined by a
Table of Contents device to measure hours of use, or
General warranty provisions 12 • Five years
Warranty period 12 Each engine is equipped with a device to meas-
Parts covered by the Warranty 13 ure hours of use. If that device fails to account for
General warranty limitations 14 hours of use due to defects in materials or work-
manship, the engine shall be warranted for a pe-
Specific warranty exclusions 15 riod of five years. The warranty period shall
Customer support 15 begin on the date the engine is delivered to the
first ultimate purchaser who, in good faith, pur-
chases the engine for purposes other than immi-
nent resale.
Emission control system war-
ranty statement
The Warranty on emission-related
General warranty provisions parts shall be interpreted as follows:
The emission control systems of your new Scan- 1. Any warranted part which is not scheduled
ia Engines (“Scania”) industrial diesel engine for replacement as required maintenance in
were designed, built and tested using genuine Scania's written instructions for maintenance
parts, and were certified as being in conformity and use of the engine by owner shall be war-
with federal emission control regulations. Scania ranted for the warranty period defined above.
warrants to the original owner, and to each sub- If any such part fails during the period of
sequent owner, of a new Scania industrial diesel warranty coverage, it shall be repaired or re-
engine (“You”) that the engine: placed by the engine manufacturer according
to Subsection (4) below. Any such part re-
1. Was designed, built and equipped so as to paired or replaced under the Warranty shall
conform at the time of sale with all applica- be warranted for the remaining warranty pe-
ble regulations under Section 213 of the riod.
Clean Air Act, 42 U.S.C. § 7547, for their
full useful life and designed, built and 2. Any warranted part which is scheduled only
equipped so as to conform with all applicable for regular inspection in Scania's written in-
regulations adopted by the California Air Re- structions for maintenance and use of the en-
sources Board pursuant to its authority under gine by owner shall be warranted for the
Chapters 1 and 2, Part 5, Division 26 of the warranty period defined above. A statement
California Health and Safety Code, and; in such written instructions to the effect of
“repair or replace as necessary” shall not re-
2. Is free from defects in material and work- duce the period of warranty coverage. Any
manship which would cause such engine to such part repaired or replaced under warran-
fail to conform to applicable regulations for ty shall be warranted for the remaining war-
its warranty period or otherwise cause the ranty period.
failure of a warranted part to be identical in
all material respects to the part as described
OPM 300 en-GB 12

3. Any warranted part which is scheduled for shall not be liable under this article to war-
replacement as required maintenance in Sca- rant failures of warranted parts caused by the
nia's written instructions for maintenance use of a non-exempted add-on or modified
and use of the engine by owner shall be war- part.
ranted for the period of time prior to the first 11. The Executive Officer of the California Air
scheduled replacement point for that part. If Resources Board may request, and in such
the part fails prior to the first scheduled re- case, the engine manufacturer shall provide,
placement, the part shall be repaired or re- any documents which describe that manufac-
placed by the engine manufacturer according turer's warranty procedures or policies.
to Subsection (4) below. Any such part re-
paired or replaced under warranty shall be
warranted for the remainder of the period
prior to the first scheduled replacement point
for the part. Parts covered by the Warranty
4. Repair or replacement of any warranted part The following is a list of parts considered to be
under the warranty provisions of this article part of the Emission Control Systems covered by
shall be performed at no charge to the owner the Emission Warranty for Scania industrial en-
at a warranty station. gines which were built to conform to federal and
California emission control regulations:
5. Notwithstanding the provisions of Subsec-
tion (4) above, warranty services or repairs 1. Fuel injection system.
shall be provided at all manufacturer distri- 2. Air induction system.
bution centers that are franchised to serve the
subject engines. 3. Exhaust manifold system.
6. The owner shall not be charged for diagnos- 4. Smoke puff limiter (included in ECU).
tic labor that leadsto the determination that a 5. Oil filler cap.
warranted part is in fact defective, provided 6. EGR system (when applicable):
that such diagnostic work is performed at a
warranty station. a) Cooler.
b) EGR valve.
7. The engine manufacturer shall be liable for
damages to other engine components proxi- 7. Exhaust brake (when applicable).
mately caused by a failure under warranty of 8. NOx sensors:
any warranted part. a) NOx sensor, engine out.
8. Throughout the engine's warranty period de- b) NOx sensor, tail pipe.
fined above, the engine manufacturer shall 9. DOC (when applicable).
maintain a supply of warranted parts suffi-
cient to meet the expected demand for such 10. SCR system:
parts. a) DEF tank.
9. Any replacement part, as defined in Section b) DEF tank level, temperature and quality
1900(b), Title 13 of the California Code of sensors.
Regulations, may be used in the performance c) DEF hose.
of any maintenance or repairs and must be d) DEF injector.
provided without charge to the owner. It is e) DEF injector pressure and temperature
not necessary for replacement parts to be the sensors.
same brand or by the same manufacturer as f) Evaporator.
the original part sold with the engine. Such g) SCR catalyst inlet temperature sensor.
use shall not reduce the warranty obligations h) SCR catalyst including the ammonia-slip
of the engine manufacturer. catalyst.
i) SCR control unit (EEC3).
10. Add-on or modified parts, as defined in Sec-
tion 1900(b), Title 13 of the California Code
of Regulations, that are not exempted by the
California Air Resources Board may not be
used. The use of any non-exempted add-on
or modified parts shall be grounds for disal-
lowing a warranty claim made in accordance
with this article. The engine manufacturer
OPM 300 en-GB 13

11. Miscellaneous items used in the above sys- Receipts covering the performance of regular
tem: maintenance should be retained in the event
a) Electronic control unit (ECU), sensors, questions arise concerning maintenance. The re-
wiring harnesses. ceipts should be transferred to each subsequent
b) Hoses, belts, connectors, assemblies, owner of the engine with the emission warranted
clamps, fittings tubing, sealing gaskets or engine. Scania cannot, however, deny warranty
devices and mounting hardware. solely for the lack of receipts or for your failure
c) Pulleys, belts and idlers. to ensure the performance of all scheduled main-
d) Emission control information label. tenance.
The Warranty covers the cost of diagnosis, repair
IMPORTANT! and replacement parts and services of warranted
components and systems performed by an au-
This list does not include all expendable mainte- thorized Scania distributor or dealer using genu-
nance parts. ine Scania parts. You may elect to have
maintenance, replacement or repair of these
• Expendable emission related parts requiring components and systems performed by any re-
scheduled maintenance are warranted until pair establishment or individual without invali-
their first scheduled replacement point. dating the Warranty.
• Emission related parts scheduled for inspec-
tion and replacement only as necessary are The use of other than Scania replacement parts
not considered expendable and if repaired or also does not invalidate the warranty on other
replaced under warranty shall be warranted components unless such parts cause damage to
for the remaining warranty period. warranted parts. However, the cost of such ser-
vices or parts will not be covered by the Warran-
See Specific Warranty Exclusions below. ty.
You are responsible for initiating the warranty
process. The California Air Resources Board
suggests that You present your heavy-duty off-
road engine to an authorized Scania dealer as
General warranty limitations soon as a problem exists. The warranty repairs
To retain the dependability of the exhaust emis- should be completed by the dealer as expedi-
sion control originally built into your Scania in- tiously as possible.
dustrial diesel engine, it is essential that the
engine is installed according to Scania installa-
WARNING!
tion instructions and emission certificates. Your
engine is designed to operate on diesel fuel only.
Use of any other fuel may result in your engine Use of replacement parts which are not of equiv-
no longer operating in compliance with state or alent quality may impair the effectiveness of
federal emissions requirements. The use of alter- emission control systems. Accordingly, it is rec-
native fuels shall not void the warranties on any ommended that only Scania repair or replace-
engine certified to use such fuel. ment parts be used for maintenance, repair or
replacement of emission control systems.
In addition, as the engine owner, You are respon-
sible for the performance of all scheduled main- If other than Scania parts are used for mainte-
tenance listed in your owner's manual, and all nance, repair or replacement, the owner should
necessary repairs, on your new Scania industrial obtain assurance that such parts are warranted by
diesel engine. Scania may deny a warranty claim their manufacturer to be equivalent to genuine
if the engine or part has failed due to abuse, ne- Scania parts.
glect, improper maintenance or unapproved
modifications.
OPM 300 en-GB 14

Specific warranty exclusions Customer support

This warranty does not cover: In the event that You do not receive the warranty
service to which You believe You are entitled
1. .Malfunctions in any part caused by any of under the Warranty, or if You need additional
the following: misuse, abuse, improper ad- support or information concerning the Warranty,
justments, modifications, alteration, tamper- please contact:
ing, disconnection, improper or inadequate
maintenance, or use of fuels not recommend- Scania USA, Inc.
ed for the engine as described in the Opera-
tor's Manual. Address: 121 Interpark Blvd, suite 1002, 78216,
San Antonio, Texas
2. Engine installation, including cooling sys-
tem, intake system and exhaust system in- Mailing address: 121 Interpark Blvd, suite
stallation, that is not completed in 1002, 78216, San Antonio, Texas
accordance with the Scania installation in-
structions and emissions certificate for this Telephone: +1 210 403 0007
engine type. Fax: +1 210 403 0211
3. Damage resulting from accidents, acts of na-
ture or other events beyond the control of E-mail: contact@scaniausainc.com
Scania. California customers shall also be furnished a
4. The replacement of expendable maintenance copy of the California Emission Control Warran-
items such as filters, hoses, belts, oil, ther- ty Statement applicable to each new Scania en-
mostat, exhaust system and coolant made in gine purchased.
connection with scheduled maintenance ser-
vices once these parts have been replaced.
5. Replacement items which are not genuine
Scania parts or not authorized by Scania.
6. Inconvenience, loss of use of the engine or
commercial loss.
7. Any engine on which the actual use cannot
be accurately determined due to a failure of
the device to track hours of use unrelated to
defects in materials or workmanship.
8. Any engine operating outside the United
States.
OPM 300 en-GB 15

California emission control warranty statement
California emission control Owner's warranty responsi-

warranty statement bilities
• As the off-road engine owner, you are respon-
Your warranty rights and obli- sible for the performance of the required
gations maintenance listed in your owner's manual.
Scania CV AB recommends that you retain
The California Air Resources Board is pleased to all receipts covering maintenance on your
explain the emission control system warranty on off-road engine, but Scania CV AB cannot
your 2016 engine. In California, new heavy-duty deny warranty solely for the lack of receipts
off-road engines must be designed, built and or for your failure to ensure the performance
equipped to meet the State's stringent anti-smog of all scheduled maintenance.
standards. Scania CV AB must warrant the • As the off-road engine owner, you should
emission control system on your engine for the however be aware that Scania CV AB may
periods of time listed below provided there has deny you warranty coverage if your off-road
been no abuse, neglect or improper maintenance engine or a part has failed due to abuse, ne-
of your engine. glect, improper maintenance or unapproved
Your emission control system may include parts modifications.
such as the fuel injection system and the air in- • Your engine is designed to operate on ultra
duction system. Also included may be hoses, low-sulfur diesel fuel only. Use of any other
belts, connectors and other emission-related as- fuel may result in your engine no longer oper-
semblies. ating in compliance with California's emis-
sions requirements.
Where a warrantable condition exists,
Scania CV AB will repair your heavy-duty off- • You are responsible for initiating the warran-
road engine at no cost to you including diagno- ty process. The ARB suggests that you pres-
sis, parts and labor. ent your off-road engine to a Scania CV AB
dealer as soon as a problem exists. The war-
ranty repairs should be completed by the
dealer as expeditiously as possible.
Manufacturer's warranty cov- If you have any questions regarding your war-
erage ranty rights and responsibilities, you should con-
tact Scania U.S.A. Inc +1-210-403-0007.
The 2016 heavy-duty off-road engines are war-
ranted for a period of five years or 3,000 hours,
whichever occurs first. If any emission-related
part on your engine is defective, the part will be
repaired or replaced by Scania CV AB.
OPM 300 en-GB 16

SCR catalytic converter
SCR catalytic converter Environmental protection measures

• The SCR catalytic converter is a manufac-
tured article that contains vanadium pentox-
WARNING!
ide, a hazardous substance. Before disposing
of, or scrapping, a spent SCR catalytic con-
The SCR catalytic converter contains vanadium verter, it should be tested for any hazardous
pentoxide, a chemical known to the State of Cal- characteristics (ignitability, corrosivity, reac-
ifornia to cause cancer. tivity, acute hazardousness, and toxicity), as
those categories are described in 22 CCR §
66261.30. If the spent SCR catalytic convert-
The SCR catalytic converter is fitted in the si- er exhibits hazardous characteristics and is
lencer and does not constitute a health hazard being disposed of, it will be considered by the
during normal use and handling. State of California to be a hazardous waste
When carrying out work on the SCR catalytic subject to Title 22, California Code of Regu-
converter which may result in exposure to dust, lations. Before disposing of hazardous waste,
safety precautions must be taken. Such work in- review and follow all pertinent federal and
cludes, for example, opening the silencer ma- California requirements.
chining and scrapping the SCR catalytic • Vanadium pentoxide is a listed commercial
converter. chemical product - P120 - pursuant to 22
CCR § 66261.33(e). According to the State of
Safety precautions when working on the SCR California, commercial chemical products
system. that are discarded or intended to be discarded
• Inhalation: If dust is inhaled, the person are hazardous wastes and are subject to all
should be provided with fresh air immediate- provisions of Title 22, California Code of
ly. Seek medical attention Regulations. Before disposing of vanadium
pentoxide, review and follow all pertinent
• Eye contact: Rinse eyes with water immedi- federal and California requirements.
ately. If irritation persists, seek medical atten-
tion. • If the SCR catalytic converter is opened for
maintenance, any dust spillages from the cat-
• Skin contact: Wash with water and soap. Re- alyst should be collected and tested for the
move contaminated clothes. presence of vanadium pentoxide prior to
• Ingestion: If large amounts have been ingest- proper disposal. Dust spillages should also be
ed, drink plenty of water and induce vomit- tested for any hazardous characteristics (ig-
ing. Seek medical attention nitability, corrosivity, reactivity, acute haz-
ardousness, and toxicity), as those categories
Environmental hazards are described in 22 CCR § 66261.30, prior to
• Vanadium pentoxide is toxic to water organ- proper disposal. If the dust contains either va-
isms and can cause detrimental long term ef- nadium pentoxide or exhibits hazardous char-
fects to water environment. acteristics and is being disposed of, it will be
considered by the State of California to be a
hazardous waste subject to Title 22, Califor-
nia Code of Regulations. Before disposing of
hazardous waste, review and follow all perti-
nent federal and California requirements.
OPM 300 en-GB 17

SCR catalytic converter
• Do not dispose of the spent SCR catalytic • Any dust from the SCR catalytic converter
converter or its constituent parts into any wa- should be removed using a vacuum cleaner
terways, storm drains or sanitary sewers. with microfilter to minimize exposure.
• Make sure that the work surface is cleaned af-
ter completed work; Vacuum first then swab.
WARNING!
• Make sure you clean your hands after work-
ing with SCR catalytic converter to avoid in-
The SCR catalytic converter contains vanadium
gestion.
pentoxide, a chemical known to the State of Cal-
ifornia to cause cancer. • Work done on the SCR catalytic converter
may generate waste considered by the State
of California to be a hazardous waste subject
Additional considerations when working on the to Title 22, California Code of Regulations.
SCR system Before disposing of hazardous waste, review
and follow all pertinent federal and California
• Carry out work on the SCR catalytic convert- requirements.
er in all well ventilated area. Use protective
goggles and gloves if there is any risk of
splashing or spraying of reductant or coolant.
• When engine is running, the exhaust system
parts can reach such high temperatures that
there is a risk of personal injury. Make sure
that the exhaust system temperature has de-
creased to a suitable level before starting to
work.
• The SCR system is heated by water from the
engine cooling system. The cooling system
runs at overpressure and when the engine is
hot the coolant is hot. Do not open any hoses
without first stopping the coolant flow in the
hose.
• A P3 type respirator/filter mask or a type
FFP3 fine dust musk, protective goggles and
gloves should be used for any work where
there is a risk of exposure to dust from the
SCR catalytic converter.
• Use a disposable overall and dispose of it
properly after machining.
• Eating, drinking or smoking while working is
not permitted.
OPM 300 en-GB 18

Engine data plate
Engine data plate

The engine data plate indicates, in the form of a
code, the engine type, its size and applications. It
also indicates the engine type power range and
operating speed. The engine EU type approval
for exhaust emissions is indicated under Output,
where applicable.
The engine power is stated on a plate which is lo-
cated on the engine control unit.
The engine serial number is stamped onto the top
of the cylinder block at the front right.
Example: DC16 084A

DC Supercharged diesel engine with air-
cooled charge air cooler.
16 Displacement in whole dm3
084 Performance and certification code. The
code indicates, together with the applica-
tion code, the normal gross engine output.
A Code for application. A means for general
industrial use.
Made b y
Type DC16 084A

Engine No 6950106
Output. 405-493 kW 2100 r pm.
348 327
Example of an engine data plate
OPM 300 en-GB 19

Component identification
1 2 3 9 10
11
8
12
7
6 13
340 424
5 4 14
The illustration shows a normal version of a DC16 engine. The engine ordered may have different equipment.
Note:
The oil cooler is located on the top of the engine
between the cylinder banks.
The water separating prefilter for the fuel is lo-
cated between the fuel tank and engine.
1. Centrifugal oil cleaner 8. Oil filter

2. Oil filler 9. EGR valve
3. Turbocharger1 10. Engine control unit
4. Starter motor 11. Engine data plate
5. Oil dipstick 12. Coolant pump
6. Valve for draining coolant 13. EGR cooler
7. Fuel filter 14. Oil plug
1. The DC16 084A/384A may be equipped with an exhaust brake which is connected to the turbocharger.
OPM 300 en-GB 20

SCR system
The illustration provides an overview of SCR
system components.
2
1
3
4 5
7
12 13 8
10
11
340 425
1. Evaporator or hydrolysis catalytic converter 8. Reductant pump and control unit
2. Pressure line for reductant 9. Coolant hose, return from tank and pump heating
3. Coolant hose for tank and pump heating 10. Exhaust gas temperature sensor
4. NOx sensor with control unit1 11. SCR catalytic converter
5. Coolant valve 12. NOx sensor with control unit
6. Reductant return line
7. Reductant tank
1. DC16 084A/384A/085A/385A only.
OPM 300 en-GB 21

Reductant tank
Reductant tanks come in 5 different sizes. The
volumes indicated for each tank are filling vol-
umes.
A filler filter with magnet is fitted in the reduct-
ant tank to prevent the reductant from becoming
contaminated when topping up. It is used when
refuelling at a filling station. A filler filter with-
out a magnet is also supplied for use when man-
ually topping up reductant.
348 425
348 422
38 litres (10 US gallons) 60 litres (15.8 US gallons)
348 421
353 442
45 litres (11.9 US gallons) 69 litres (18.2 US gallons)

348 426
70 litres (18.5 US gallons)
OPM 300 en-GB 22

Starting and running

Note:
When the engine is started for the first time, car-
ry out the maintenance items listed under First
start in the maintenance schedule. See the Main-
tenance section.
Always check the following before running:

• oil level
• coolant
• fuel level
• electrolyte level in batteries
• state of charge of the batteries
• condition of the drive belt
• the level in the reductant tank, if the engine is
equipped with an SCR system.
WARNING!
Running the engine without reductant in the re-

ductant tank violates emissions legislation and
will damage the SCR system.
Checks before running

Carry out daily maintenance as described in the
maintenance schedule prior to operation. See the
Maintenance section.
WARNING!
Block the starting device when working on the

engine. If the engine starts unexpectedly, there is
a serious risk of injury.
OPM 300 en-GB 23

Reductant pump
When the reductant pump is new, the check
valves may need to be slackened.
IMPORTANT!
Blow the reductant pump suction nipple with

compressed air (approx. 6 bar) for at least 3 sec-
onds before starting the engine for the first time.
Start the reductant pump immediately after the
reductant tank has been filled for the first time.
336 838
Reductant pump
OPM 300 en-GB 24

Starting the engine

For environmental reasons the Scania engine has
been developed to be started with a low fuel feed.
Using unnecessarily large amounts of fuel when
starting the engine always results in emissions of
unburnt fuel.
1. Open the fuel cock if fitted.
2. Disengage the engine.
3. If the engine has a battery master switch:
Connect the power using the battery master
switch.
4. Start the engine.
If the fuel tank has been run dry or if the engine

has not been used for a long time, bleed the fuel
system.
WARNING!
Never use starter gas or similar agents to help

start the engine. An explosion may occur in the
intake manifold with a risk of personal injury.
Only start the engine in a well ventilated area.
When the engine is run in an enclosed space,
there must be effective devices to extract exhaust
gases and crankcase gases.
IMPORTANT!
The starter motor must only be cranked twice for

30 seconds at a time. After that, it must rest for at
least 5 minutes before the next attempt to start it.
OPM 300 en-GB 25

Starting at low temperatures and at

high altitudes
Take the local environmental requirements into
account. Use a fuel heater and engine heater to
avoid starting problems and white smoke.
Scania recommends that an engine heater should
be used if the engine will be used at temperatures
below -10°C or at an altitude of more than 2,000
metres.
A low engine speed and a moderate load on a
cold engine limits white smoke, gives better
combustion and warms up the engine more
quickly than warming it up with no load.
Avoid running it longer than necessary at idling
speed.
OPM 300 en-GB 26

Running
Check instruments and warning lamps at regular
intervals.
Engine speed range
600-750 rpm Low idling. Engine idling is controlled by the engine management system.
Low idling up to 2,100 rpm Engine operating speed range. Controlled by the engine management sys-
tem.
2,100-2,600 rpm Unsuitable operating speed, but a slightly higher engine speed than the nor-
mal maximum operating speed may occur when load is low or negative.
2,600-3,000 rpm Prohibited engine speed.
Emission control
The system provides a warning if there are faults
on the SCR system or if the level of reductant in
the reductant tank is too low. In the case of some
faults, for example if doser cooling is not work-
ing, the torque is reduced.
Reaction at low reductant level
Reductant Warning Torque reduction1

level lamp
20% Constant
light
10% Flashing Torque is reduced by
1% per minute to
70% of the highest
319 562
torque
0% Flashing rap- Torque is reduced to Symbol for low reductant level
idly 0% (low idling)
within 2-10 minutes
1. Applies only to engines that are certified according to Tier
4.
The engine resumes normal torque after reduct-

ant has been filled to a level of at least 20%.
OPM 300 en-GB 27

Reaction to fault in SCR system
Time Warning Torque reduction1

lamp
Fault detect- Constant
ed light
After 30 Flashing Torque is reduced by
minutes 1% per minute to
70% of the highest
319 563
torque
After 4 hours Flashing rap- Torque is reduced to
idly 0% (low idling) Symbol for fault in SCR system
within 2-10 minutes
1. Applies only to engines that are certified according to Tier
4.
Once the fault has been remedied and the engine

control unit has received an indication that it is
working, torque returns to the normal level.
If a new fault occurs within 40 hours of operation
since the first fault, the warning lamp will come
on. After 30 minutes of operation, the warning
lamp will flash rapidly and torque will be re-
duced to 0% (low idling) within 30 minutes.
IMPORTANT!
If the torque has been reduced to 0% (low

idling), the engine control unit does not detect
that the SCR system is functioning again. A ser-
vice technician must then reset the system so that
the torque returns to the normal level.
Note:
The torque reduction applies only to engines that
are certified according to Tier 4.
OPM 300 en-GB 28

Coolant temperature Oil pressure

Normal coolant temperature during operation is Information about the normal oil pressure and
80-90°C/176-194°F. lowest permitted oil pressure is contained in the
section headed Technical Data.
Alarm levels are set in the engine control unit.
The default setting for the lowest and highest The engine management system has the follow-
limit values for high coolant temperature are ing alarm levels:
95°C/203°F and 105°C/221°F respectively.
• At an engine speed below 1,000 rpm and an
The following function is standard as alarm for oil pressure below 0.7 bar/10.2 psi.
high coolant temperature: • At an engine speed above 1,000 rpm and an
• Alarm and torque reduction at the lowest lim- oil pressure below 2.5 bar/36.3 psi for longer
it value. than 3 seconds.
Depending on the engine configuration, the fol- The following function is standard as alarm for
lowing alarm functions may also be available: incorrect oil pressure:
• Alarm only. • Alarm and torque reduction by 30%.

• Alarm and engine shutdown at the highest Depending on the engine configuration, the fol-
limit value. lowing alarm functions may also be available:
• Alarm, torque reduction at the lowest limit
• Alarm only.
value and engine shutdown at the highest lim-
it value. • Alarm and engine shutdown.
• Alarm and engine shutdown at the highest • Alarm and engine shutdown override control.
limit value with the possibility of engine shut-
down override control. Note:
• Alarm, torque reduction at the lowest limit High oil pressure (above 6 bar/87 psi) is normal
value and engine shutdown at the highest lim- when starting a cold engine.
it value, with the possibility of engine shut-
down override control.
If run for extended periods under an extremely

light load, the engine may have difficulty in
maintaining the coolant temperature. At an in-
creased load the coolant temperature rises to the
normal value.
IMPORTANT!
An excessively high coolant temperature can

damage the engine.
OPM 300 en-GB 29

Charging indicator lamp Engine shutdown

If the lamp comes on during operation: 1. Run the engine without a load for a few min-
• Check and adjust the alternator drive belts as utes if it has been run continuously with a
described under the corresponding mainte- heavy load.
nance item. See the Maintenance section. 2. Switch off the engine.
If the charging indicator lamp is still on, this Note:

could be due to an alternator fault or a fault in the
electrical system. The battery voltage must remain on for a few
seconds after the 15 voltage is switched off so
that the control units can store the values and
switch to standby mode.
Belt transmission 10 prohibited engine shutdowns will cause a
When the belt transmission is new, it may make torque reduction (70% of fuel quantity). Reset
a squeaking noise when running. The noise is the engine by switching it off correctly once.
normal and disappears after 50-100 hours of op-
eration.
The noise does not affect the service life of the IMPORTANT!
belt transmission.
There is risk of post boiling and of damage to the
turbocharger if the engine is switched off with-
out cooling.
Driving at high altitude
When driving at high altitudes engine power is The power must not be switched off before the
reduced automatically due to the lower oxygen engine has stopped.
content in the air. It is then not possible to run the If the engine is equipped with a battery master
engine at maximum power. switch and an SCR system, the SCR system must
Note: run for a while after the ignition has been
switched off to allow it to cool down. During this
Driving at a higher height than 4,000 metres period the power must not be cut using the bat-
above sea level is only permitted if it has first tery master switch.
been approved by Scania.
OPM 300 en-GB 30

Checks after running
WARNING!

There is always a risk of sustaining burns when
an engine is hot. Particularly hot parts are ex-
haust manifolds, turbochargers, oil sumps, hot
coolant and oil in pipes and hoses.
1. Check that the power supply has been cut.

2. Top up the fuel tank. Make sure that the filler
cap and the area round the filler opening are
clean to avoid contamination of the fuel.
3. Top up the reductant tank. Make sure that the
filler cap and the area round the filler open-
ing are clean to avoid contamination of the
reductant.
4. If there is a risk of freezing, the cooling sys-
tem must contain enough glycol.
5. If the temperature is below 0°C/32°F: Pre-
pare for the next start by connecting the en-
gine heater (if fitted).
IMPORTANT!
Check the coolant level following the first start.

Top up if necessary.
OPM 300 en-GB 31

Maintenance
Maintenance
IMPORTANT!
The maintenance programme covers a number of
points that are divided into the following sec- On delivery a Scania engine is optimised for its
tions: application. However, regular maintenance is
necessary to:
• Lubrication system
• Cooling system • prevent unplanned stops
• Air cleaner • extend the service life of the engine
• Fuel system • maximise the long-term emission perfor-
mance of the engine
• Miscellaneous
• give the best possible operating economy.
WARNING!

The maintenance programme includes the fol-

lowing:
• S maintenance: Minimum basic maintenance.
• M maintenance: More extensive mainte-
nance.
• L maintenance: Includes nearly all mainte-
nance items.
• XL maintenance: Includes all maintenance
items.
XL
L L
M M M
S S S S S S
500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
313 153
OPM 300 en-GB 32

Maintenance
Engines with few hours of op-

eration
IMPORTANT!
On engines with few hours of operation, mainte-

nance must be carried out annually or every 5
years.
Stand-by generator sets and the like that are not

used regularly should be test run and checked in
accordance with the manufacturer's instructions.
The following maintenance items must be car-
ried out once the engine has been warmed up to
operating temperature.
1. Checking oil level.
2. Checking coolant level.
3. Checking the vacuum indicator.
4. Checking fuel level.
5. Check for engine leaks.
Cleaning the engine
WARNING!
Beware of hot water! Use suitable protective

equipment.
The engine must be cleaned before starting work.

Clean the engine with hot water. Also use a de-
greasing agent, if necessary.
Avoid spraying water on the engine control unit,
see illustration.
Environment
314 835
The washing water must be disposed of in com-

pliance with the relevant national and interna- Clean within the marked area.
tional regulations.
OPM 300 en-GB 33

Maintenance
Maintenance intervals
Daily First time at Interval (hours) At least

first start 500 500 1,000 2,000 6,000 annu- every
R S M L XL ally 5
years
Lubrication system
Checking oil level X X
Changing the oil X X X X X X
Cleaning the centrifugal oil
X X X X X X
cleaner
Renewing the oil filter X X X X X X
Cooling system
Checking coolant level X X X X X X X
Checking antifreeze and corro-
X X X X
sion inhibitor
Cleaning the cooling system and
X X
changing coolant
Air cleaner
Reading the vacuum indicator X X X X X X
Renewing the filter element X X X
Renewing the safety cartridge X X X
Fuel system
Checking fuel level X X
Renewing the fuel filter X2 X X X X
Miscellaneous
Checking the drive belt X X X X X
Checking for leaks X X X X X
Checking and adjusting the
X X X
valve clearance
Renewing the reductant filter X X X X
Cleaning the reductant tank filler
X X X X
filter
Cleaning the reductant tank ven-
X X X
tilation filter
2 Applies to DC16 072.
OPM 300 en-GB 34

Lubrication system
Lubrication system
Oil grade
Scania LDF stands for the Scania Long Drain
Field test standard. Approved Scania LDF oils
have been carefully selected after extensive test-
ing. The approval is only granted to the highest
quality engine oils available on the market.
Recommended oil
Scania Oil LDF
Scania Oil LDF-2
Scania Oil LDF-3
Scania Oil E7
The engine oil must fulfil the following quality

requirements:
• ACEA E5/API CI-4
• ACEA E7/API CI-4+
• For engines not run on low-sulphur fuel, the
TBN (Total Base Number) should be at least
12 (ASTM D2896).
• Oils with a low ash content (ACEA E9/API
CJ4) are not recommended.
Check with your oil supplier that the oil meets

these requirements.
If the engine is used in areas of the world where
lubricating oil with ACEA or API classification
is not available, the oil grade must be measured
in actual operation. In this case contact the near-
est Scania workshop.
For operation at extremely low outdoor tempera-
tures: Consult your nearest Scania representative
on how to avoid starting difficulties.
Viscosity class Outdoor temperature

SAE 20W-30 -15 °C (5 °F) - +30 °C (86 °F)
SAE 30 -10 °C (14 °F) - +30 °C (86 °F)
SAE 40 -5 °C (23 °F) - > +45°C (113°F)
SAE 50 0 °C (32 °F) - > +45°C (113°F)
SAE 5W-30 < -40°C (-40°F) - +30 °C (86 °F)
SAE 10W-30 -25 °C (-13 °F) - +30 °C (86 °F)
SAE 15W-40 -20 °C (-4 °F) - > +45°C (113°F)
OPM 300 en-GB 35

Lubrication system
Oil analysis
To be able to extend the oil change intervals us-
ing an oil analysis, Scania LDF-2 and LDF-3 oils
must be used.
Oil companies can offer analysis of the engine
oil.
The following conditions must remain fulfilled
when the oil is changed.
• Viscosity at 100°C (212°F): max. ±20% of
original value of the fresh oil.
• TBN (in accordance with ASTM D4739): >
3.5
• TBN (in accordance with ASTM D4739): >
TAN (in accordance with ASTM D664)
• Soot (DIN 51452): < 3%
Such analysis measures the oil's TBN (Total

Base Number), TAN (Total Acid Number), fuel
dilution, water content, viscosity and the quanti-
ty of particles and soot in the oil.
The result of a series of analyses is used as the
basis for establishing a suitable oil change inter-
val.
If the conditions are changed, a new oil analysis
programme must be carried out to establish new
change intervals.
Checking oil level
Checking the oil level with the engine 2

switched off
Note:
Leave the engine off for at least 1 minute before
checking the oil level. 1
1. Remove the oil dipstick (1) and check the oil

level. The correct level is between the mini-
mum and maximum marks on the oil dip-
stick.
312 506
2. Top up with more oil (2) when the oil level is

at or below the lower mark.
Information on the correct oil type is found under

the heading Oil grade.
OPM 300 en-GB 36

Lubrication system
Changing the oil

Note:
Renew the oil filter and clean the centrifugal oil
cleaner when changing oil.
WARNING!
Hot oil can cause burns and skin irritation. Wear

protective gloves and goggles when changing
hot oil. Make sure that there is no pressure in the
345 618
lubrication system before starting work on it.
The oil filler cap must always be in place when Min. 40 litres (10.5 US gallons).
starting and running the engine to prevent oil be-
ing ejected. Max. 48 litres (12.6 US gallons).
Environment
Use a container to avoid spillage. Used oil must

be disposed of as specified in national and inter-
national law.
Note:
Change oil more often if the engine is subjected
to particularly demanding operation, such as a
dusty environment, or if deposits in the centrifu-
346 279
gal oil cleaner are thicker than 28 mm (1.1 in).
Min. 29 litres (7.6 US gallons).
1. Unscrew the oil plug and drain the oil when Max. 37 litres (9.7 US gallons).
the engine is hot. In certain engines the oil is
pumped out by means of a bilge pump.
When draining with the valve, the oil should
be hot. Alternatively, use a pump. This so
that draining occurs more quickly.
2. Clean the magnet on the oil plug.
3. Refit the oil plug. 25°
4. Top up with oil.
25°
5. Check the level on the oil dipstick.
30° 30°
Maximum angles of inclination during opera-
tion
25°
Maximum permissible angles during operation 25°

vary, depending on the type of oil sump; see il-
343 840
30° 30°
lustration.
OPM 300 en-GB 37

Lubrication system
Labels for top-up engine oil

grade
When changing oil it is important to use the cor-
rect engine oil grade.
The oil filler cap must be clearly marked with a
label showing the top-up oil grade.
If the label is missing or if the engine oil grade is

changed, a new label must be fitted.
336 492
Filling label in the cylinder block.
353 114
Filling label in the rocker cover.
Parts
Oil grade Colour Part No. Part No.

Filling in the cylinder Filling in the rocker cover
block
Scania LDF-2 Blue 2 132 424 2 296 064
Scania LDF-3 Red 2 132 426 2 296 066
Scania LDF Grey 2 269 345 2 296 071
ACEA E7 White 2 132 425 2 296 065
Scania Low Ash Green 2 132 427 2 296 067
Scania Bioethanol Black 2 132 428 2 296 068
Scania BEO-2 Orange 2 258 841 2 296 070
ACEA E9 - 2 132 429 2 296 069
OPM 300 en-GB 38

Lubrication system
Cleaning the centrifugal oil

cleaner
Designation Illustration
Torque wrench 2-20 Nm with exchangeable ratchet head
340 130
When cleaning the centrifugal oil cleaner there
will be some dirt deposits in the rotor cover. If
this is the case, this indicates that the rotor is
working. If it is clean and not working, the cause
must be established immediately.
If the dirt deposit exceeds 28 mm at the recom-
mended intervals, the rotor cover should be
cleaned more often.
WARNING!
The oil may be hot. Carefully remove the cover x 1.5

from the centrifugal oil cleaner.
1. Clean the cover. Unscrew the nut securing

the outer cover.
2. Let the oil run out from the rotor.
3. Lift out the rotor. Wipe off the outside. Undo
the rotor nut and unscrew it about 1.5 turns to
133 315
protect the bearing.
Note:
Take care not to damage the rotor shaft.
OPM 300 en-GB 39

Lubrication system
4. If the rotor nut is difficult to get loose, turn

the rotor upside down and fasten the rotor nut
in a vice. Turn the rotor anti-clockwise
1.5 turns by hand or use an M20 nut, see il- M20
lustration.
IMPORTANT!
The rotor must not be put in a vice. Never strike x 1.5

the rotor cover. This may cause damage resulting
in imbalance.
133 316
5. Remove the rotor cover by holding the rotor
in both hands and tapping the rotor nut
against the table. Never strike the rotor di-
rectly as this may damage its bearings.
133 317
OPM 300 en-GB 40

Lubrication system
6. Remove the strainer from the rotor cover. If

the strainer is stuck, insert a screwdriver be-
tween the rotor cover and strainer and care-
fully prise them apart.
127 878
7. Remove the paper insert and scrape away
any remaining dirt deposits inside the rotor
cover. If the deposits are thicker than 28 mm,
the centrifugal oil cleaner must be cleaned
more often.
333 044
8. Wash the parts.

9. Inspect the 2 nozzles on the rotor. Ensure that
they are not blocked or damaged. Renew any
damaged nozzles.
10. Check that the bearings are undamaged.
333 037
OPM 300 en-GB 41

Lubrication system
11. Fit a new paper insert on the inside of the ro-

tor cover.
2 3 4
337 178
OPM 300 en-GB 42

Lubrication system
12. Fit the strainer onto the rotor.

13. Fit a new O-ring by sliding it over the strain-
er.
14. Refit the rotor cover. Ensure that the O-ring
is not outside the cover.
15. Screw the rotor nut back on by hand.
16. Check that the shaft is not damaged or loose.
127 881
Note:
Take care not to damage the rotor shaft.
17. Refit the rotor and rotate it by hand to make

sure it rotates easily.
313 612
OPM 300 en-GB 43

Lubrication system
18. Fit a new O-ring in the cover. Refit the cover

and tighten the lock nut. Tightening torque
15 Nm.
IMPORTANT!
To reduce the risk of oil leakage it is important to

tighten the cover to the correct tightening torque.
Note:
A torque wrench together with a ratchet head is
suitable for use during maintenance of the cen-
trifugal oil cleaner.
313 611
Operational testing
Operational testing need only be carried out if it
is suspected that the centrifugal oil cleaner is not
working properly. For example, if there is an ab-
normally small amount of deposit in the centrif-
ugal oil cleaner in relation to the distance driven.
The rotor rotates very fast and should continue to
turn when the engine has stopped.
1. Run the engine until it is warm.
2. Turn off the engine and listen for the sound
from the rotor. Use your hand to feel if the
333 039
filter housing is vibrating.

3. If the filter housing is not vibrating, disman-
tle and check the centrifugal oil cleaner.
OPM 300 en-GB 44

Lubrication system
Renewing the oil filter

Hexagon socket, 1/2” drive, 36 mm
118 268
IMPORTANT!
Clean the centrifugal oil cleaner when renewing

the oil filter.
Otherwise, the oil filter will be blocked and re-
sistance in the filter will increase. If this happens,
an overflow valve in the filter retainer opens and
lets the oil pass without being filtered.
1. Unscrew the filter cover with the socket.
IMPORTANT!
Do not use an adjustable spanner or other open

tool as there is risk of damaging the filter cover.
2. Lift out the filter housing cover with filter el-

ement. The filter housing will drain automat-
ically once the filter has been removed.
3. Renew the O-ring in the cover. Lubricate the
O-ring with engine oil.
4. Press a new filter into the snap fastener in the
314 827
cover and tighten the filter cover to 25 Nm

(18 lbf/ft).
OPM 300 en-GB 45

Cooling system
Cooling system Coolant resistance to cold

The following example shows coolant properties
Coolant with 30 percent by volume of antifreeze and cor-
rosion inhibitor:
WARNING! • Ice slush starts to form at -16°C (3°F).

• At -30°C (-22°F), there is a risk of cooling
Ethylene glycol can be fatal if ingested and can system malfunction.
cause skin irritation and eye damage. • There is no risk of damage by freezing with a
minimum antifreeze and corrosion inhibitor
content of 35 percent by volume.
The coolant recommended by Scania is a mix-
ture of water with antifreeze and corrosion inhib- The chart depicts coolant properties at different
itor (ethylene glycol). The coolant has several percents of antifreeze and corrosion inhibitor
characteristics which are important for the oper- concentration by volume.
ation of the cooling system:
• Corrosion inhibitor 0 10 20 30 40 50 %
0
• Antifreeze
-10
• Increases the boiling point 1
-16
-20
The coolant should always contain 35-55% by
volume of antifreeze and corrosion inhibitor so -30
that the coolant properties ensure that the coolant 3 2
works correctly. -40
Note:
312 505
-50
The coolant should be changed when the cooling
system is cleaned: every 6,000 hours or at least °C B A
every 5 years. Refer to Changing coolant.
Curve A: Ice formation starts (ice slush)
Curve B: Damage by freezing occurs
Area 1: Safe area
Area 2: Malfunctions may occur (ice
slush)
Area 3: Risk of damage by freezing
OPM 300 en-GB 46

Cooling system
Antifreeze and corrosion inhibitor con-

centration table
35% by volume of Scania antifreeze provides
sufficient protection against corrosion.
Example:
1. The total volume of the cooling system is 40
litres in this example.
2. The measured concentration of ethylene gly-
col is 35% by volume (freezing point -21
°C). According to the table there are 14 litres
of ethylene glycol in the cooling system.
3. The required concentration of ethylene gly-
col is 45% by volume (freezing point -30
°C). According to the table, 18 litres of eth-
ylene glycol are required in the cooling sys-
tem.
4. Since there are already 14 litres in the cool-
ing system, 4 litres of ethylene glycol must
be added to the cooling system (18 - 14 = 4
litres).
For calculation Adequate protection against corrosion

Volume of ethylene glycol Cooling system
(%) 20 25 30 35 40 45 50 60 volume (litres)
Ice slush forms (°C) -6 -9 -12 -21 -24 -30 -38 -50
5 6 8 11 12 14 15 18 30
6 8 10 14 16 18 20 24 40
8 10 13 18 20 23 25 30 50
9 12 15 21 24 27 30 36 60
11 14 18 25 28 32 35 42 70
12 16 20 28 32 36 40 48 80
14 18 23 32 36 41 45 54 90
15 20 25 35 40 45 50 60 100
Volume of ethylene glycol (li- 17 22 28 39 44 50 55 66 110
tres) 18 24 30 42 48 54 60 72 120
20 26 33 46 52 59 65 78 130
21 28 35 49 56 63 70 84 140
23 30 38 53 60 68 75 90 150
24 32 40 56 64 72 80 96 160
26 34 43 60 68 77 85 102 170
27 36 45 63 72 81 90 108 180
29 38 48 67 76 86 95 114 190
30 40 50 70 80 90 100 120 200
OPM 300 en-GB 47

Cooling system
Antifreeze and corrosion inhibitor con-

centration table
35% by volume of Scania antifreeze provides
sufficient protection against corrosion.
Example:
1. The total volume of the cooling system is
10.6 US gallons in this example.
2. The measured concentration of ethylene gly-
col is 35% by volume (freezing point -6°F).
According to the table there are 3.7 US gal-
lons of ethylene glycol in the cooling system.
3. The required concentration of ethylene gly-
col is 45% by volume (freezing point -22°F).
According to the table, 4.8 US gallons of eth-
ylene glycol are required in the cooling sys-
tem.
4. Since the cooling system already contains
3.7 US gallons, fill another 1.1 US gallons of
ethylene glycol in the cooling system (4.8 -
3.7 = 1.1 US gallons).
For calculation Adequate protection against corrosion

Volume of ethylene glycol Cooling system
(%) 20 25 30 35 40 45 50 60 volume (US gal-
Ice slush forms (°F) 21 16 10 -6 -11 -22 -36 -58 lons)
1.3 1.6 2.1 2.9 3.2 3.7 4 4.8 7.9
1.6 2.1 2.6 3.7 4.2 4.8 5.3 6.3 10.6
2.1 2.6 3.4 4.8 5.3 6.1 6.6 7.9 13.2
2.4 3.2 4 5.5 6.3 7.1 7.9 9.5 15.9
2.9 3.7 4.8 6.6 7.4 8.5 9.2 11.1 18.5
3.2 4.2 5.3 7.4 8.5 9.5 10.6 12.7 21.1
3.7 4.8 6.1 8.5 9.5 10.8 11.9 14.3 23.8
4 5.3 6.6 9.2 10.6 11.9 13.2 15.9 26.4
Volume of ethylene glycol 4.5 5.8 7.4 10.3 11.6 13.2 14.5 17.4 29.1
(US gallons) 4.8 6.3 7.9 11.1 12.7 14.3 15.9 19 31.7
5.3 6.9 8.7 12.2 13.7 15.6 17.2 20.6 34.3
5.5 7.4 9.2 12.9 14.8 16.6 18.5 22.2 37
6.1 7.9 10 14 15.9 18 19.8 23.8 39.6
6.3 8.5 10.6 14.8 16.9 19 21.1 25.4 42.3
6.9 9 11.4 15.9 18 20.3 22.5 26.9 44.9
7.1 9.5 11.9 16.6 19 21.4 23.8 28.5 47.6
7.7 10 12.7 17.7 20.1 22.7 25.1 30.1 50.2
7.9 10.6 13.2 18.5 21.1 23.8 26.4 31.7 52.8
OPM 300 en-GB 48

Cooling system
Checking coolant level Checking antifreeze and cor-

The following instructions apply to Scania ex- rosion inhibitor
pansion tanks. For other types of expansion
tanks, follow the manufacturer's instructions. Designation Illustration
Refractometer
WARNING!
Never open the coolant filler cap when the en-

gine is hot. Hot coolant and steam may spray out
and cause burns.
305 523
If the cap has to be opened do it slowly and care-
fully to release the pressure before removing the
138008
cap. Wear gloves as the coolant is still very hot.
Note:
Use only pure fresh water that is free from parti-
1. Open the expansion tank cap and check the cles, sludge and other impurities.
coolant level.
– The right coolant level on a cold engine is
even with the lower edge of the filler neck. 1. Pour a small amount of coolant into a con-
– The right coolant level on a hot engine is tainer and check that the coolant is pure and
approximately 25 mm (1 in) over the low- clear.
er edge of the filler neck. 2. Change the coolant if it is contaminated or
2. Top up with coolant as necessary. cloudy.
3. Measure the antifreeze and corrosion inhibi-
tor content with a refractometer.
IMPORTANT!
Do not top up large quantities of coolant through The following rules apply to ethylene glycol-
the expansion tank. Top up in accordance with based coolant:
the instructions in the section headed Changing
coolant instead. • The antifreeze and corrosion inhibitor content
must be minimum 35 percent by volume for
corrosion protection to be sufficient.
• An antifreeze and corrosion inhibitor content
IMPORTANT!
greater than 55 percent by volume impairs the
ability to protect against frost.
Never fill a large amount of cold coolant in a hot
engine. There is great risk of cracks forming in • If ice forms in the coolant, there are disrup-
the cylinder block and cylinder heads. tions initially, but there is no immediate risk
of damage. The engine should not be subject-
ed to heavy loads when ice starts to form.
IMPORTANT!
Only pour pre-mixed coolant into the cooling

system.
OPM 300 en-GB 49

Cooling system
Antifreeze and corrosion in-

hibitor
Only the product Scania coolant, or other prod-
ucts that are tested to provide proper antifreeze
and protection against corrosion for Scania, may
be used in Scania engines. Products that do not
satisfy the requirements for use in a Scania en-
gine can result in faults in and damage to the
cooling system. This can lead to the invalidation
of Scania's warranty for faults and damage
caused by the use of inappropriate coolant.
The antifreeze and corrosion inhibitor used in
Scania engines should be of the ethylene glycol
type.
Scania concentrate
Designation Contents Part No. Volume Volume
litre US gallons
Coolant Antifreeze and corrosion inhibitor (concentrate) 1 894 323 5 1.3
Coolant Antifreeze and corrosion inhibitor (concentrate) 1 894 324 20 5.3
Coolant Antifreeze and corrosion inhibitor (concentrate) 1 894 325 210 55
Coolant Antifreeze and corrosion inhibitor (concentrate) 1 894 326 1,000 264
Scania Ready Mix

Designation Contents Part No. Volume Volume
litre US gallons
Coolant Scania antifreeze and corrosion inhibitor Ready Mix 1 921 955 5 1.3
50/50
Coolant Scania antifreeze and corrosion inhibitor Ready Mix 1 921 956 20 5.3
50/50
Coolant Scania antifreeze and corrosion inhibitor Ready Mix 1 921 957 210 55
50/50
Coolant Scania antifreeze and corrosion inhibitor Ready Mix 1 896 695 1,000 264
50/50
OPM 300 en-GB 50

Cooling system
Changing coolant Filling coolant
IMPORTANT! Designation Illustration

Coolant trolley
Mix the coolant as specified in the section head-
ed Coolant.
333 980
Draining coolant
1. Remove the expansion tank cap.
2. Drain the coolant at the following two IMPORTANT!
points:
Lowest point of the cylinder block. When it is necessary to fill a large quantity of
The lowest point of the cooling system. coolant, it must be pumped in from underneath.
This is to ensure that air does not get into the
3. Close the drain taps.
cooling system, which can cause the coolant
pump to overheat.
Environment
1. Use a Scania coolant trolley, or other suitable
Avoid spillage and use a suitable container. Used equipment, to fill with coolant through the
coolant must be disposed of as specified in na- drain valve on the cylinder block. This facil-
tional and international law. itates the venting of the engine.
2. Start the engine when the cooling system has
been filled. Allow the engine to run for a
while. Then check the coolant level and top
up with coolant as necessary.
3. Air pockets may still be left in the cooling
system, which will disappear after the engine
has been operated for a period of time. It
may, therefore, need some topping up to start
with.
OPM 300 en-GB 51

Cooling system
Cleaning the cooling system
WARNING!
When handling cooling system detergent: Read

the warning text on the package concerned.
IMPORTANT!
Do not use caustic soda or other alkaline deter-

gent as this could damage the aluminium.
Note:
Clean the cooling system more often than speci-
fied in the maintenance interval if necessary.
External: Cleaning the radiator and

charge air cooler
1. Check that the radiator and the charge air
cooler are not clogged on the air side and that
the cooling fins are not damaged.
2. Carefully scrape away any deposits from the
radiator cooling fins. Use a paraffin-based
engine cleaner if necessary.
3. Carefully straighten bent cooling fins using a
steel brush or the like.
OPM 300 en-GB 52

Cooling system
Internal: Removing oil and grease Internal: Removing deposits

1. Run the engine until it has reached operating 1. Run the engine until it has reached operating
temperature and then drain the cooling sys- temperature and then drain the cooling sys-
tem. tem.
2. Remove the thermostats. 2. Remove the thermostats.
3. Fill the system with clean, hot water mixed 3. Fill the system with clean, hot water mixed
with liquid dishwasher detergent intended with some commercially available radiator
for household machines. Concentration 1% detergent which is based on sulphamic acid
(0.1/10 l). and contains dispersing agents. Follow the
4. Warm up the engine for approximately 20-30 manufacturer's instructions for the concen-
minutes. Remember to switch on the cab tration and cleaning period.
heating system, if one is installed. 4. Run the engine for the specified time. Re-
5. Drain the cooling system. member to switch on the cab heating system,
if one is installed.
6. Fill the system with clean, hot water and run
the engine for about 20-30 minutes. 5. Drain the cooling system.
7. Drain the water from the cooling system. 6. Fill the cooling system with clean, hot water
and run the engine for about 20-30 minutes.
8. Refit the thermostats.
7. Drain the water from the cooling system.
9. Fill the cooling system with new coolant fol-
lowing the specification under Coolants ear- 8. Refit the thermostats.
lier in the document. 9. Fill the system with new coolant following
the specification under Coolants earlier in
the document.
Environment Environment
Avoid spillage and use a suitable container. Used Avoid spillage and use a suitable container. Used
coolant must be disposed of as specified in na- coolant must be disposed of as specified in na-
tional and international law. tional and international law.
OPM 300 en-GB 53

Air cleaner
Air cleaner
Reading the vacuum indicator

If the indicator's red plunger is fully visible, re-
new or clean the air cleaner filter element follow-
ing the instructions.
Renewing the filter element
326 671
Note:
Renew the filter element earlier than the mainte-
nance interval if the indicator shows red. A B
There is always a risk that the filter element will

be damaged when it is cleaned.
The filter element must not be cleaned in water
or be blown clean with compressed air.
WARNING!
336 100
Never start the engine without the air filter as this
could cause injury and severe engine damage. A Vacuum indicator.
B Filter element.
1. Remove the cover from the air cleaner.
2. Renew the filter element.
3. Carry out a check by inserting an inspection
lamp into the element and checking from the
outside that there are no holes or cracks in the
filter paper.
4. Assemble the air cleaner.
5. Reset the vacuum indicator by pressing the
button.
OPM 300 en-GB 54

Air cleaner
Renewing the safety cartridge
IMPORTANT!
When renewing the safety cartridge, take great

care to ensure that no dirt or other impurities get
into the engine. Do not remove the safety car-
tridge unnecessarily.
1. Remove the cover from the air cleaner.

2. Remove the filter element.
3. Remove the safety cartridge.
4. Fit a new safety cartridge.
5. Renew or clean the filter element.
6. Assemble the air cleaner.
OPM 300 en-GB 55

Fuel system
Fuel system
IMPORTANT!
The whole fuel system is very sensitive to dirt

and even very small particles. Foreign particles
in the system can cause serious malfunctions. It
is therefore very important that everything is as
clean as possible when work is carried out on the
fuel system. Before starting work on the fuel sys-
tem, the engine must be washed. If possible, a
hot water wash should be used.
It is strictly forbidden to carry out any machining
work or work with compressed air near an open
fuel system.
Be extra careful and always use clean, lint-free
and dust-free clothes and gloves when working
on the fuel system. Scania recommends using
Tegera 848 gloves.
Clean tools before they are used and do not use
any worn or chrome-plated tools. Material and
flakes of chrome may come off.
Clean connections and the surrounding area be-
fore removal. When cleaning, cloths or paper
which shed fibres must not be used. Use clean
and lint-free cloths.
Plug or cover the connections during removal.
Also clean the connections before fitting the
components. Removed components should be
placed on a thoroughly cleaned, dust-free sur-
face. Cover with a lint-free cloth.
Checking fuel level

• Check the fuel level and top up with fuel as
necessary.
Note:
The fuel system must be bled if the tank has been
run dry. Refer to the Bleeding the fuel system
section.
OPM 300 en-GB 56

Fuel system
Renewing the fuel filter using

a bleeding tool
Engines with XPI have dual fuel filters in the
form of a water separating suction filter and a
pressure filter.
Removal
118 268
Bleeding tool
337 296
Environment
Avoid spillage and use a suitable container. Used

fuel must be disposed of as specified in national
and international law. B
To ensure that the filter housings are drained

properly, the filter covers must be removed as
follows:
IMPORTANT!
Start with the water separating suction filter (A).

Do not open the pressure filter cover (B) until the
filter housing for the water separating filter (A) is
completely drained.
A
329 246
OPM 300 en-GB 57

Fuel system
IMPORTANT!
Do not use an adjustable spanner or other open

tool to undo the filter covers, as this risks damag-
ing the filter covers. A
1. Make a mark on the water separating suction

filter cover (A). Unscrew the cover 3 to 4
turns, use the socket.
IMPORTANT!
329 247
Wait a minimum of 2 minutes to allow as much
of the fuel as possible to drain out of the filter
housing.
2. Unscrew the filter cover (A) and lift it up

slowly with the filter element.
3. Make sure the bleeding tool is completely
drained before starting work. Draw out any
remaining fuel and any particles using the
bleeding tool.
4. Keep the bleeding tool hose in the filter
housing for the water separating suction fil-
ter (A).
A
329 248
OPM 300 en-GB 58

Fuel system
5. Make a mark on the pressure filter cover (B). B

Unscrew the cover 3 to 4 turns, use the sock-
et. Draw out fuel which may drain into the
water separating suction filter housing when
the pressure filter is detached.
IMPORTANT!
Wait a minimum of 2 minutes to allow as much

of the fuel as possible to drain out of the filter
housing.
329 249
6. Unscrew the pressure filter cover (B) and lift
it up slowly with the filter element. B
7. Fuel from the pressure filter housing (B) will
flow into the water separating suction filter
housing (A). Leave the bleeding tool in the
water separating suction filter housing (A)
until it is completely drained of fuel.
A
329 250
OPM 300 en-GB 59

Fuel system
8. Move the bleeding tool to the pressure filter

housing (B). Draw out remaining fuel and
particles.
B
IMPORTANT!
It is important to remove remaining fuel and par-

ticles from the filter housings to prevent fuel sys-
tem contamination.
9. Undo the old filter elements from the covers

by carefully bending them to one side.
329 251
OPM 300 en-GB 60

Fuel system
Fitting
118 268
1. Unpack the new filter elements and the sup-
plied O-rings.
IMPORTANT!
Check that there is no remaining packaging ma-

terial stuck to the new filter elements.
2. Fit the new O-rings to the covers. Lubricate

the O-rings with O-ring grease.
3. Press the filter elements into the snap fasten-
ers on the covers.
4. Check that the filter housings are clean be-
fore fitting.
IMPORTANT!
• Fit the filter elements in the filter covers be-

fore placing them in the fuel filter housings or
the filter elements may be damaged.
• Open the bleed nipple to prevent back pres-
sure in the filter housings when the filter ele-
ments are screwed on.
5. Press down the filter elements into the fuel

filter housings with the filter covers.
6. Screw on the filter covers. Use the socket.
7. Check that there is no gap between the filter
cover and the filter housing. If there is a gap,
repeat the procedure and make sure that the
bleed nipple is open.
OPM 300 en-GB 61

Fuel system
Bleeding the fuel system us-

ing a bleeding tool
Bleeding tool
337 296
1. Open the bleed nipple at the high pressure
pump and connect a clear plastic hose from
the bleeding tool.
2. Drain the bleeding tool. Hold the bleeding

tool straight and draw out a full container of
fuel. Bleeding is now complete.
329 252
OPM 300 en-GB 62

Miscellaneous
Miscellaneous
Checking the drive belt
IMPORTANT!
Refit the drive belt with the same direction of ro-

tation as it had before removal.
Check the drive belt thoroughly, particularly at

the idler rollers.
314 906
Check the drive belt for cracks.
The drive belt must be renewed if it has cracks. 106 229
OPM 300 en-GB 63

Miscellaneous
Check drive belt wear.
112 931
The drive belt is starting to become worn, but can be
refitted.
Checking for leaks
112 932
IMPORTANT! The belt is worn down to the cord. The drive belt
must be renewed.
If serious leakage occurs, contact your nearest
workshop.

2. Check for oil, coolant, fuel, air or exhaust
leaks.
3. Tighten or renew leaking connections.
Check the overflow holes which show
whether the O-rings between the cylinder
liners and crankcase are leaking.
4. Check whether the drain hole on the coolant
pump is blocked. If there is leakage: Renew
the seal in the pump or the entire coolant
pump.
OPM 300 en-GB 64

Miscellaneous
Checking and adjusting the

valve clearance
Special tools
Number Designation Illustration

99 309 Turning tool for rotating the flywheel from below.
142 238
WARNING!

Note:
Checking and adjusting valve clearances should
also be done one more time after the first 500
hours of operation. Then the normal interval will
follow (every 2,000 hours).
Check and adjust the valve clearance with the en-

gine cold.
Intake valve clearance 0.45 mm (0.018 in)

Exhaust valve clearance 0.70 mm (0.028 in)
Max. clearance between two valves under the

same valve bridge is 0.2 mm.
346 529
OPM 300 en-GB 65

Miscellaneous
Turn the flywheel in the direction of rotation of

the engine using the turning tool. Read the mark
on the flywheel in the lower window of the fly-
wheel housing.
Note:
Valve transition occurs when the cylinder
switches from exhaust stroke to intake stroke.
The exhaust valve is closing while the intake
valve is opening.
310 343
Openings for taking readings on the flywheel hous-
ing.
1 2 3 4
314 908
5 6 7 8
Cylinder location.
OPM 300 en-GB 66

Miscellaneous
IMPORTANT!
Remember to remove the flywheel rotation tool

after adjustment.
Reading in the lower Valve transition on Adjust intake valve on Adjust exhaust valve on
window cylinder cylinder cylinder
TDC down (0°) 6 7 and 8 4 and 5
TDC up (180°) 7 1 and 5 2 and 6
TDC down (360°) 1 2 and 4 3 and 7
TDC up (540°) 4 3 and 6 1 and 8
It is a good idea to mark the rocker arm with a

pen after adjustment to keep track of what has al-
ready been adjusted.
Alternate adjustment table

5 1 5 1
A B
6 2 6 2
7 3 7 3
8 4 8 4
5 1 5 1
C D
6 2 6 2
7 3 7 3
8 4 8 4
121 052
OPM 300 en-GB 67

Miscellaneous
Renewing the reductant filter

118 268
1. Remove the cover on the rear of the reduct-
ant tank.
316 163
2. Place a suitable container underneath.
3. Unscrew the filter cover. Use the socket.
4. Remove the filter cover and O-ring.
326 565
OPM 300 en-GB 68

Miscellaneous
5. Remove the frost protection device (C) and

the filter (B).
6. Wipe the pump clean (A).
7. Fit the new filter (B).

8. Fit the new frost protection device (C).
9. Lubricate the threads with the spray.
A
10. Fit the new O-ring (D) in the new cover (E).
11. Check that the frost protection device and
valve ring are correctly fitted in the new cov-
er.
12. Fit the new cover and tighten to 80 Nm (59 B
lbf/ft).
336 879
A Pump.
B Filter.
C Frost protection device.
D O-ring.
E Cover.
OPM 300 en-GB 69

Miscellaneous
Cleaning the reductant tank

filler filter
Make sure that the filler filter (1) is clean. If it is
dirty: Clean the filler filter with clean water and 1
refit it.
350 114
Cleaning the reductant tank
ventilation filter
Make sure that the ventilation filter (2) is clean.
If it is dirty: Clean the ventilation filter with
clean water and refit it. 2
352 009
OPM 300 en-GB 70

Diesel
Diesel Sulphur content of fuel
Composition of the fuel It is important to use low-sulphur fuel

It is important for sulphur-free or ultra-low sul-
The composition of the fuel is extremely impor- phur fuel to be used on engines with SCR sys-
tant for the operation and service life of the en- tems certified in accordance with Stage III B/
gine and injection system. The engine output and Tier 4i and Stage IV/Tier 4f to ensure that the
exhaust gases are also dependent on the fuel engine operates correctly. Use of the wrong fuel
grade. grade can cause damage to the engine and the ex-
The requirements and testing standards for the haust gas aftertreatment system.
most important characteristics are described in From January 2011 legislation in the USA and
the Workshop Manual which can be ordered Europe requires all diesel engines not used on the
from Scania dealers or directly from Scania. road to be run on sulphur-free or ultra-low sul-
The table shows some of the key properties. phur fuel.
Property Requirement REQUIREMENT!

Viscosity at 40°C 2.0-4.5 cSt In Europe, the fuel should be sulphur-free ac-
(104°F) cording to standard EN 590. This means that the
Density at 15°C (59°F) 0.82-0.86 cSt sulphur content must not exceed 10 ppm.
Ignitability (CET rating) minimum 49 In the USA the fuel must be an ultra-low sulphur
Flashpoint 56°C (132°F) fuel in accordance with standard ASTM D975.
Particulate contamina- ISO 11500, This means that the sulphur content must not ex-
tion level ceed 15 ppm.
class 22/20/17
Responsibility
IMPORTANT!
The machine operator is responsible for using

the correct type of fuel to ensure that local laws
are complied with.
OPM 300 en-GB 71

Diesel
Permitted sulphur content in fuel
Engine type Max. sulphur content in fuel for Note

unaffected oil change intervals
Engines without EGR and SCR Up to 2,000 ppm (0.2%) If the sulphur content is higher than
2,000 ppm, the oil change intervals
must be halved. A higher sulphur
content than 4,000 ppm is not per-
mitted, since this will result in en-
gine damage.
Engines with SCR only Up to 500 ppm (0.05 %) A higher sulphur content than 15
ppm may only be used where
Stage III A/Tier 3 or less restrictive
emission laws apply.
Engines with both EGR and SCR Up to 350 ppm (0.035%) A higher sulphur content than 15
ppm may only be used where
Stage III A/Tier 3 or less restrictive
emission laws apply. A higher sul-
phur content than 350 ppm is not
permitted, since this will result in
engine damage.
Fuel with a higher sulphur content

than 15 ppm for engines with SCR
systems
If fuel with a higher sulphur content than that
specified in the standard is used on a short-term
basis, this will not cause permanent damage to a
catalytic converter. The catalytic converter may,
however, require fuel with a low sulphur content
for some time after this to regain its normal effi-
ciency.
If fuel with too high a sulphur content is used for
a prolonged period, there is a risk that the cata-
lytic converter will not operate correctly, which
will result in a reduction in engine torque.
OPM 300 en-GB 72

Diesel
Temperature dependency of Biodiesel (FAME)

the fuel Scania uses the term biodiesel according to the
At temperatures lower than those specified for EN 14214 standard to refer to renewable diesel
the fuel, paraffin wax may precipitate from the which is made from greases or oils and metha-
fuel and block filters, pipes and hoses. The en- nol. The biodiesel should conform to the require-
gine can then lose power or stop. ments of European standard EN 14214. For
biodiesel in accordance with EN 14214 the ge-
The fuel is adapted for use in the specific climate neric term FAME is frequently used.
of each country. If a vehicle or an engine is to be
operated in a temperature zone with a tempera- Scania XPI engines are approved for diesel ac-
ture lower than normal, first identify the temper- cording to the EN 590 standard. EN 590 contains
ature properties of that particular fuel. up to 7% biodiesel in accordance with
EN 14214.
The properties of the fuel when cold can be im-
proved by adopting one of the following meas-
ures before the temperature drops:
Use of fuel oil in stand-by
• Install an electric fuel heater if this particular generator sets
fuel is not suitable for the expected tempera-
ture and no fuel is available with the correct Long-term storage of diesel, where the diesel
temperature properties. comes into contact with water, may lead to the
growth of micro organisms (bacteria and fun-
• Add 0.5-2% alcohol (isopropanol) to prevent
gus). To avoid this in fuel used in stand-by gen-
any water in the fuel from freezing and form-
erator sets, i.e. ESP engines, Scania permits the
ing plugs of ice. Drain fuel tanks and drain or
use of fuel oil according to DIN 51603-1 and
renew fuel filters regularly.
ÖNORM C 1109.
Use of fuel oil is only permitted for ESP engines
IMPORTANT! and under the following conditions:
Mixing kerosene or other paraffins with the fuel • The fuel must not be stored or used in temper-
is prohibited. The injectors may be damaged. atures under -10°C (14°F).
Mixing petrol with the fuel is prohibited. In the • The engine must not be equipped with an
long term petrol can cause wear in the injectors SCR system.
and engine.
Definition of ESP
ESP is an output class for stand-by generator sets
in accordance with ISO 8528, which states that
stand-by generator sets may be used under vary-
ing loads for a maximum of 200 hours/year.
ESP engines are intended for use as stand-by
power supplies in the efficient electrical net-
works in Europe, North and South America,
Australia, New Zealand, Japan and Taiwan.
OPM 300 en-GB 73

Reductant for SCR
Reductant for SCR Properties

Reductant is a urea solution normally known as Reductant in accordance with ISO 22241 is a
AdBlue, DEF or ARLA 32 depending on the solution consisting of urea and water containing
market. With SCR, the reductant is added to the 32.5% by weight of urea. The solution freezes at
exhaust gases before the catalytic converter. This approximately -11°C. When the solution freezes,
reduces nitrogen oxide emissions. ice and urea always maintain the same concen-
tration. Always store reductant at a temperature
between -11°C and 30°C.
Responsibility and quality re- Rec. % by weight of Limit value according

quirements urea to ISO 22241
32.5% 31.8-33.2%
IMPORTANT!
Reductant is normally colourless if no dye has
The machine operator is responsible for using been added. It is not harmful to the skin. Nor is it
the correct type of reductant to ensure that local toxic in small quantities, but it tastes very un-
laws are complied with. pleasant.
Reductant has a low surface tension and rapidly
spreads over large areas, which then become
very slippery. Reductant is extremely corrosive,
REQUIREMENT! especially to aluminium and copper. Therefore,
wash off any spillages on metal and electrical
In order for the emission control to meet the connections as soon as possible. Water works
emission requirements set by the public authori- very well for cleaning purposes. Please use hot
ties, the reductant should be specified in accord- water.
ance with ISO 22241.
Reductant can dry out and form white or greyish
brown crystals or deposits. Dense deposits which
have been formed as a result of heat may need to
be scraped off or heated to more than 500°C.
OPM 300 en-GB 74

Preparing the engine for storage
Preparing the engine for Preservative coolant

storage If the engine is to be stored with a full cooling
system, use coolant containing 50 percent glycol
If the engine is not being used for an extended by volume. Glycol without nitrite-based inhibi-
period its cooling system, fuel system and com- tor should be used. Example: BASF G48 or
bustion chamber and outside must be protected BASF D542.
against rust.
An alternative to preparing the engine for long- WARNING!
term storage is to start the engine and warm it up
every 6 months.
Ethylene glycol can be fatal if ingested. Avoid
contact with the skin.
Handling the engine

The engine can normally stand idle for up to 6
months without preparation. For longer periods Preservative fuel
of downtime, the following measures should be
taken. These measures provide protection for ap- Use diesel mixed with Lubrizol 560H or the
proximately 4 years. equivalent. Mix 1 cm3 (ml)/0.06 in3 Lubrizol
560H in 10 dm3/2.3 US gallons of fuel.
Preparations for storage:
1. Thoroughly clean the engine. WARNING!
2. Run the engine for a specific period using
special preservative fuel, oil and coolant. Lubrizol 560H contains aromatic hydrocarbons
3. Otherwise prepare the engine for storage (fil- which are hazardous to health.
ter renewal, lubrication, etc.).
• Use spot extractors where there is a danger of
If the engine is equipped with an SCR system: vapour build-up.
The reductant in the SCR system is perishable. If • Wear protective goggles and gloves when
it is not used, its quality can deteriorate over handling the fuel.
time. The reductant tank and the SCR system • Do not use contaminated clothing.
should therefore be drained and cleaned after
longer stationary periods. • If it gets in your eyes: Flush with a gentle jet
of water for at least 15 minutes and contact a
doctor.
IMPORTANT! • If it gets on your skin: Wash with soap and
water.
Reductant is a highly corrosive fluid which must
not come into contact with materials which are • If you inhale it: Fresh air, rest and warmth.
sensitive to corrosion. • Store in well-sealed containers in a dry, cool,
place out of the reach of children.
Rinse off reductant spillages with plenty of wa-
ter. Lubrizol is flammable and has a 2A fire rating.
The flashpoint is 27 °C/81°F. In case of fire: Ex-
If reductant seeps into electrical connections or tinguish with carbon dioxide, powder or foam.
electrical cables, these must be renewed.
OPM 300 en-GB 75

Preservative oil 10. Drain the preservative oil from the engine.
Fill with new engine oil immediately or
Suitable preservative oils are supplied by most when the engine is to be reused.
oil companies. Example: Dinitrol 40 or equiva-
11. Drain the coolant if the engine is not to be
lent.
stored with coolant in the system. Plug and
tape all coolant connections if the engine is
to be stored without a cooling system.
Preparations for storage 12. Air cleaner: Clean or renew the filter ele-
ment.
Environment 13. Cover air intakes and exhaust pipes.
14. Alternator and starter motor: Spray with wa-
Use a container to avoid spillage when draining ter-repellent anti-corrosive oil, CRC 226,
the oil, coolant and reductant. Dispose of used LPS1 or the equivalent.
fluids through an authorised waste disposal con- 15. Spray the outside of bright engine parts, first
tractor. with penetrating preservative oil such as
Dinitrol 25B and then with Dinitrol 112 or
1. Drain and flush the cooling system. Top up
the equivalent.
with preservative coolant. Clearly mark the engine with the storage prepa-
2. Warm up the engine on normal fuel. Stop the ration date, and state that the engine must not be
engine and drain the oil. started or cranked.
3. Renew the fuel filter. If the engine is to stand idle for more than a year:
4. Fill the engine with preservative oil up to the
minimum level on the oil dipstick. 16. Drain the reductant from the reductant tank.
5. Mix preservative fuel in a can. Detach the
fuel pipe at the feed pump suction line and
connect a hose from the can.
6. Detach the fuel pipe at the overflow valve
and connect a return hose to the can.
7. Start the engine and run it at about 1,000 rpm
for 20-25 minutes.
8. Stop the engine, remove the hoses and con-
nect the normal fuel pipes.
9. Remove the rocker covers and lubricate the
valve mechanisms with plenty of preserva-
tive oil. Refit the rocker covers.
Note:
Do not remove the injectors.
OPM 300 en-GB 76

Batteries Storage
Remove the batteries and trickle charge them at After the preparations, the engine should be
the battery charging station. This does not apply stored in a dry and warm place (room tempera-
to batteries specified as maintenance-free by the ture).
manufacturer.
The same applies to short-term storage, even if
the engine has not been prepared for storage as When the engine is to be taken into
above. operation again
1. Remove plugs and tape from coolant connec-
tions, air intakes and exhaust pipes.
WARNING!
2. Fill the cooling system with coolant. For
more information refer to Maintenance.
Wear gloves and protective goggles when charg-
ing and handling batteries. The batteries contain 3. Check the oil level in the engine or top up
a highly corrosive acid. with fresh engine oil.
4. Lubricate the valve mechanisms and their
pushrods and valve tappets as well as the in-
jector mechanisms with plenty of oil.
5. Drain the preservative fuel from the fuel
manifold and fuel filter.
6. Connect and bleed the fuel system. For more
information refer to Maintenance.
7. Wash off any preservative oil on the outside
using white spirit.
If the engine is equipped with an SCR system

which has been drained and cleaned:
8. Fill the reductant tank with reductant.
OPM 300 en-GB 77

Technical data
Technical data
General data
Number of cylinders and configuration V8

Working principle 4-stroke engine
Cylinder diameter (mm/in) 130/5.118
Piston stroke (mm/in) 154/6.06
Displacement (dm3/in3) 16.4/1,001
Firing sequence 1-5-4-2-6-3-7-8
Compression ratio
DC16 084A/384A 17.4:1
Other engine types 16.7:1
Engine direction of rotation viewed from rear Anti-clockwise
Fan direction of rotation viewed from front Clockwise
Cooling Coolant
Valve clearances, cold engine
Intake valve (mm/in) 0.45/0.017
Outlet valve (mm/in) 0.70/0.027
Number of teeth on the flywheel 158
Low idling (rpm) 600-750
Maximum full-load speed (rpm) 2,100
Fuel Diesel
Approximate weight, without coolant and oil (kg/lb)
DC16 084A/384A 1,375/3,031
Other engine types 1,340/2,954
Lubrication system
Oil volume See Maintenance

Oil cleaning Centrifugal oil cleaning
Oil cooler Coolant cooled, full
flow
Oil filter Paper filter from Scania
Interval between oil changes (h) 500
Oil pressure (bar)
Normal with the engine at operating temperature, operating speed 3-6
Minimum permitted at idling speed 0.7
Crankcase pressure with closed crankcase ventilation (mbar) -5.4 to 2.0
OPM 300 en-GB 78

Technical data
Injection system
Type XPI (Extra High Pres-

sure Injection)
Engine management system EMS
Fuel filter Paper filter from Scania
Fuel filter with water separator Paper filter from Scania
Cooling system
Coolant volume, excluding radiator (dm3/US gallons)

DC16 084/384A 26/6.9
Other engine types 24/6.3
Coolant volume including 1.5 m2 radiator (dm3/US gallons) 68/18.0
Coolant temperature (°C/°F) 90-95/194-203
Number of thermostats 1
Thermostat opening temperature (°C/°F) 80/176 and 87/189
Intake system
Permissible pressure drop in the intake system with cleaned or new fil- 30
ter (mbar)
Permissible pressure drop in the intake system with blocked (dirty) fil- 65
ter (mbar)
Electrical system
Type 1-pin, 24 V, DC
Starter motor, standard equipment 1-pin, 24 V, 7.0 kW
Alternator, standard equipment 1-pin, 28 V, 100 A
OPM 300 en-GB 79

Scania Assistance
Scania Assistance
Wherever you are, you can always get assistance from the Scania service organisation, Scania Assistance,
all day, every day of the year.
Always call the contact for your country.
AR 0800 999 722 642 IE +353 71 9634000

AT +43 1 256 44 11 IT +39 0461 996 222
AU 1300 SCANIA KR +82 1588 6575
1300 722642 LU +32 226 400 000
BE +32 2 264 00 00 MA +34 91 678 92 13
BG +359 886 660001 MX 01 800 4SCANIA
BR 0800 019 42 24 NL +31 70 4182666
CA +1-800-2-SCANIA NO +47 223 217 00
CH +41 800 55 24 00 PL +48 602 622 465
CL 188 800 722 642 PT +48 91 678 9247
CZ +420 225 020 225 RO +40 723 27 27 26
DE +49 261 887 8888 SE +46 42 100 100
DK +45 333 270 44 SK +421 903 722 048
ES +34 91 678 80 58 TR +90 212 335 04 40
FI +358 10 555 24 TZ +255 78 472 2642
FR +33 2 414 132 32 US 1-800-2-SCANIA
GB 0 800 800 660 UY 0800 8351
+44 1274 301260 ZA 0800 005 798
GR +30 6944 420 410 +27 11 661 9823
HU +36 209 727 197
Other countries: +46 8 52 24 24 24

Note:
Calls will be recorded for training purposes.
OPM 300 en-GB 80


Scania DC16 XPI Service & Operator Manual - EN

Uploaded by

Copyright:

Available Formats

Scania DC16 XPI Service & Operator Manual - EN

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Scania DC16 XPI Service & Operator Manual - EN

Uploaded by

Copyright:

Available Formats

Important information

Serious risk of injury

Engine serial number

OPM 300 en-GB 2

OPM 300 en-GB 3

To ensure the maximum performance and the

The information in this manual was correct at the

OPM 300 en-GB 4

Environment and safety Different types of advisory

OPM 300 en-GB 5

Note: Safety precautions for running the

OPM 300 en-GB 6

Hazardous gases Running

All fuels and lubricants as well as many chemi-

OPM 300 en-GB 7

Chemicals Safety precautions for maintenance

Working with a running engine always poses a

OPM 300 en-GB 8

Hot surfaces and fluids Batteries

Scania recommends that Scania spare parts are

OPM 300 en-GB 9

Electric welding Cooling system

Always hand in used oil to an authorised waste

OPM 300 en-GB 10

Before starting Certification

Otherwise, the instructions in the Operator's

For Scania to guarantee that the engine corre-

OPM 300 en-GB 11

Scania engines engine war- in the engine manufacturer's application for

Where a warrantable condition exists, Scania

OPM 300 en-GB 12

OPM 300 en-GB 13

OPM 300 en-GB 14

Specific warranty exclusions Customer support

OPM 300 en-GB 15

California emission control Owner's warranty responsi-

OPM 300 en-GB 16

SCR catalytic converter Environmental protection measures

OPM 300 en-GB 17

OPM 300 en-GB 18

Engine data plate

Example: DC16 084A

Type DC16 084A

Example of an engine data plate

OPM 300 en-GB 19

1. Centrifugal oil cleaner 8. Oil filter

OPM 300 en-GB 20

1. DC16 084A/384A/085A/385A only.

OPM 300 en-GB 21

45 litres (11.9 US gallons) 69 litres (18.2 US gallons)

70 litres (18.5 US gallons)

OPM 300 en-GB 22

Starting and running

Always check the following before running:

Running the engine without reductant in the re-

Checks before running

Block the starting device when working on the

OPM 300 en-GB 23

Blow the reductant pump suction nipple with