TIL308, TIL309 Numeric Displays With Logic
TIL308, TIL309 Numeric Displays With Logic
TIL308, TIL309 Numeric Displays With Logic
SOLID-STATE DISPLAYS WITH INTEGRAL TTL MSI CIRCUIT CHIP FOR USE
IN ALL SYSTEMS REQUIRING A DISPLAY OF BCD DATA
• 6,9-mm (0.270-Inch) Character Height • Internal TTL MSI Chip With Latch, Decoder,
• TIL308 Has Left Decimal and Driver
• TIL309 Has Right Decimal • Constant-Current Drive for Light-Emitting
• Easy System Interface
Diodes
mechanical data
These assemblies consist of display chips and a TTL MSI chip mounted on a header with a red molded plastic
body. Multiple displays may be mounted on 11,43-mm (0.450-inch) centers.
PIN ASSIGNMENTS
Pin 1 QB Pin 9 NC
Pn 2 QC Pin 10 B
Pin 3 QD Pin 11 BI
Pin 4 QA Pin 12 DP 3,56 (0.140)
Pin 5 LS Pin 13 LT 2,79 (0.110)
Pin 6 C Pin 14 QDP
Pin 7 D Pin 15 A
Pin 8 GND Pin 16 VCC
Seating Plane
(see Note A)
4,32 (0.170) MIN
0,56 (0.022)
0,46 (0.018)
CL of Pin 1
4,42 (0.174) DIA All Pins
7,87 (0.310)
7,62 (0.300) 1,52 (0.060)
3,81 (0.150) Decimal Point 1,02 (0.040)
TIL309
CL of Pin 1
1
2,54 (0.100) 4,45 (0.175)
6,45 (0.254) 3,94 (0.155)
4 Places
10°
Logic Chip
Decimal Point
TIL308
TIL308 TIL309
A A
F B F B
G G
TOP VIEW E C E C 10,67 (0.420)
D.P. D.P. 9,65 (0.380)
D D
ALL LINEAR DIMENSIONS ARE IN MILLIMETERS AND PARENTHETICALLY IN INCHES
NOTES: A. Lead dimensions are not controlled above the seating plane.
B. Centerlines of character segments and decimal points are shown as dashed lines. Associated dimensions are nominal.
C. The true-position pin spacing is 2,54 mm (0.100 inch) between centerlines. Each centerline is located with 0,26 mm (0.010 inch) of
its true longitudinal position relative to pins 1 and 16.
PRODUCTION DATA information is current as of publication date. Copyright 1992, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
logic diagram
Latch Outputs
QDP QD QC QB QA
BI VCC
LS To Logic Chip
A
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Latch f b
Data C
g
Inputs
e c
d
dp
DP
TL308 has left decimal.
TL309 has right decimal.
LT
TIL308, TIL309
NUMERIC DISPLAYS WITH LOGIC
SLBS002–D1096, MARCH 1972–REVISED SEPTEMBER 1992
description
These internally-driven seven-segment light-emitting-diode (LED) displays contain a five-bit latch and a
decoder/LED driver in a single 16-pin package. A description of the functions of the inputs and outputs of these
devices are in the terminal function table.
The TTL MSI circuits contain the equivalent of 78 gates on a single chip. Logic inputs and outputs are completely
TTL/DTL compatible. The buffered inputs are implemented with relatively large resistors in series with the bases
of the input transistors to lower drive-current requirements to one-half of that required for a standard Series
54/74 TTL input.
Some of the additional features of these displays are as follows:
• Latched BCD and decimal point logic outputs provided to drive logic processors simultaneously with the
displayed data
• Minimum number of inputs required . . . 4-line BCD plus decimal point
• Overriding blanking for suppressing entire display or pulse-modulation of LED brightness
• LED test input to simultaneously turn on all display segments and decimal point
• Can be operated in a real-time mode or latched-update-only mode by use of the latch strobe input
• Displays numbers 0 through 9 as well as A, C, E, F, or minus sign
• Can be blanked by entry of BCD 13 or by use of the blanking input
• Decimal point controlled independently with decimal-point latch
• Constant-current-source TTL-LED interface for optimum performance.
The latch outputs except QDP are active pullup, and each one, except QDP, is capable of driving three standard
Series 54/74 loads. The LED driver outputs are designed specifically to maintain a relatively constant on-level
current of approximately 7 mA through each LED segment and decimal point. All inputs are diode-clamped to
minimize transmission-line effects, thereby simplifying system design. Power dissipation is typically 575 mW
with all segments on.
Terminal Functions
PIN
DESCRIPTION
NAME NO.
BLANKING Input (BI) 11 When low, will blank (turn off) the entire display. Mus be high for normal operation of the display.
Latch Data Inputs 15, 10, 6, Data on these inputs are entered into the latches under the control of the latch strobe input. The binary
A, B, C, D, DP 7, 12 weights of the inputs are: A = 1, B = 2, C = 4, D = 8. DP is decimal point latch data input.
Latch Outputs 4, 1, 2, 3, The BCD data that drives the decoder is stored in the five latches and is available at these outputs. The
QA, QB, QC, QD, 14 binary weights of the outputs are: QA = 1, QB = 2, QC = 4, QD = 8. QDP is decimal point latch output.
QDP
LATCH STROBE 5 When low, the data in latches follow the data on the latch inputs. When high, the data in the latches are held
Input (LS) constant and are unaffected by new data on the latch inputs.
LED TEST Input (LT) 13 When low, will turn on the entire display, overriding the data in the latches and the blanking input. Must be
high for normal operation of the display.
FUNCTION TABLE
LATCH INPUTS BLANKING LED LATCH OUTPUTS DISPLAY
FUNCTION
D C B A DP STROBE INPUT TEST QD QC QB QA QDP TIL308 TIL309
0 L L L L L L H H L L L L L
1 L L L H H L H H L L L H H
2 L L H L L L H H L L H L L
3 L L H H H L H H L L H H H
4 L H L L L L H H L H L L L
5 L H L H H L H H L H L H H
6 L H H L L L H H L H H L L
7 L H H H H L H H L H H H H
8 H L L L L L H H H L L L L
9 H L L H H L H H H L L H H
A H L H L L L H H H L H L L
Minus Sign H L H H H L H H H L H H H
C H H L L L L H H H H L L L
Blank H H L H H L H H H H L H H
E H H H L L L H H H H H L L
F H H H H H L H H H H H H H
Blank X X X X X X L H X X X X X
LED TEST (LT) X X X X X X X L X X X X X
H = high level, L = low level, X = irrelevant.
DP input has arbitrarily been shown activated (high) on every other line of the table.
absolute maximum ratings over operating case temperature range (unless otherwise noted)
Supply voltage, VCC (see Note 1): Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Nonrepetitive peak, tw ≤ 100 ms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating case temperature range, TC (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 85°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 25°C to 85°C
NOTES: 1. Voltage values are with respect to network ground terminal.
2. Case temperature is the surface temperature of the plastic measured directly over the integrated circuit. Forced-air cooling may be
required to maintain this temperature.
Output VCC
RL
From Output
Under Test
CL = 15 pF
TYPICAL CHARACTERISTICS
RELATIVE LUMINOUS INTENSITY
vs
RELATIVE SPECTRAL CHARACTERISTICS CASE TEMPERATURE
1 4
0.7
1
0.6
0.7
0.5
0.4 0.4
0.3
0.2 0.2
0.1
0 0.1
600 620 640 660 680 700 0 10 20 30 40 50 60 70
λ – Wavelength – nm TC – Case Temperature – °C
Figure 2 Figure 3
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.