General Features The SEL-PSM provides the following features: ➤ Converts station battery control power to electronic power levels. ➤ Powers up to four SEL-DTA Display/Transducer Adaptors located remotely from SEL protective relays. ➤ Use wherever a reliable, industrial source of low-voltage dc is required. ➤ Triple outputs: +5 V, +12 V, –12 V or +5 V, +15 V, –15 V models available. ➤ Four output ports ease connection to multiple loads. ➤ Two wide input voltage ranges available: 30–60 Vdc; 85–280 Vdc/85–265 Vac. ➤ Alarm contact closes for loss of +5 V output. ➤ Power input and alarm connections are standard 10-32 screw terminals. ➤ Power fail detect signals at each output port indicate loss of dc to loads. ➤ Red LED indicates power-on condition. ➤ Designed for mounting inside switchboards; does not require panel space.
Date Code 20080530 Instruction Manual SEL-PSM Power Supply Module
2 Installation Instructions
Installation Instructions Refer to Figure 3 for dimensions, mounting hole locations, terminals, and connectors. Refer to Figu for more details on the output port connections. Step 1. Mount the SEL-PSM Power Supply Module to a flat surface. Step 2. Connect Terminal 3 of the terminal block to frame ground. Step 3. Connect Terminals 4 and 5 to the input power. Observe polarity for the 48 V rated supplies. Polarity is unimportant for the 125 V rated supplies. Step 4. If desired, connect Terminals 1 and 2 to an annunciator to signal loss of power. The alarm contacts are closed when no power is applied. Under normal operating conditions the alarm contacts are held open. Step 5. Connect loads to one or more of the output ports. See Figure 1 for the output connector pinouts. 4 5 3 1. Ground and Common 2. Power Fail Detect Output 9 3, 4, 5. No Connections 6 2 6. +5 V Output 7. +12/+15 V Output 7 1 8. –12/–15 V Output 8 9. Ground and Common
Figure 1 Female Chassis Connector, Exterior View
Refer to Figure 2 for connection of the SEL-PSM to power an SEL-DTA.
Cable Cable SEL 362 363 1 SEL-DTA ALARM Relay 2 Cable Cable 3 Ground SEL 362 363 4 Control SEL-DTA 5 Power Relay Cable Cable 362 363 SEL-PMS SEL SEL-DTA Power Relay Supply Cable Cable Module SEL 362 363 SEL-DTA Relay
Maximum Cable Lengths
Cable 362: 50' Cable 363: 5'
Notice of Proprietary Information
Information contained herein is proprietary and is property of Schweitzer Engineering DWG: No. A7-0427 Laboratories, Inc. Where furnished with a proposal, the recipient shall use it soley for Date: 10-21-88 purposes of inspection, installation, or maintenance. Where furnished to a supplier, it Rev. 12-07-88 shall be used soley in the performance of work contracted for by this company. The information shall not be used or disclosed by the recipient for any other purpose whatsoever.
Figure 2 Connection of SEL-PSM to Power an SEL-DTA
SEL-PSM Power Supply Module Instruction Manual Date Code 20080530
Installation Instructions 3
.200" DIA 4 Places
6.500"
8.000"
.750"
1.000" 7.500" .375" 7.918"
9.500"
Figure 3 SEL-PSM Top and Side Views
4.10" Max 3.04"
.46" Max
Notice of Proprietary Information
Information contained herein is proprietary and is property of Schweitzer Engineering Dwg. No. A7-0428 Laboratories, Inc. Where furnished with a proposal, the recipient shall use it soley for Date: 10-21-88 purposes of inspection, installation, or maintenance. Where furnished to a supplier, it Rev: 11-22-88 shall be used soley in the performance of work contracted for by this company. The information shall not be used or disclosed by the recipient for any other purpose whatsoever.
Figure 4 Mounting Diagram
Date Code 20080530 Instruction Manual SEL-PSM Power Supply Module
4 Installation Instructions
Table 1 SEL-PSM Assembly List
Quantity Description SEL Part Number
1 Circuit board B530
1 Chassis 190-1590 1 Bottom cover 190-1600 4 Male connectors 090-0310 2 SEL-PSM instruction manuals PMPSM-01 1 25 W power supply 48 Vdc +5, +15/–15 V 230-0201 (500-1230) 48 Vdc +5, +12/–12 V 230-0401 (500-1210)
125/250 Vdc +5, +15/–15 V 230-0301 (500-1220)
125/250 Vdc +5, +12/–12 V 230-0501 (500-1200)
SEL-PSM Power Supply Module Instruction Manual Date Code 20080530
Date Code 20080530 Figure 5 –HV +HV GND C102 R105 LINE GND +LINE -LINE F101 C101 Q103 MOV101 R104
Instruction Manual K101 SCHWEITZER ENGINEERING LABORATORIES SEL-PSM BOARD COPYRIGHT 1988 MADE IN U.S.A. D104 MOV102 X4-0406
Outputs +5 V: 3 A max current +12/+15 V: 0.3 A max current –12/–15 V: 0.3 A max current Ripple: 20 mV peak-to-peak maximum Switching noise: 2 MHz at 20 kHz repetition rate; 1% or 100 mV peak-to-peak maximum, whichever is less Short circuit protection limits current; automatic resets upon removal of overload. Output tolerance: +5/–5% Power Fail Detect Output One signal per output port Normal level: +5 V through 3.3 kΩ Power failure level: less than 1 V when sinking up to 50 mA (maximum)
Isolation Input power and alarm circuits are routine tested at 3000 Vdc. Power and power-fail detect outputs are ground-referenced.
Temperature Ranges Operating: –20° to + 55°C Storage: –55° to +85°C
Standards ANSI/IEEE C37.90-1978 “IEEE Standard Relay and Relay Systems Associated with Electrical Power Apparatus” applies to power input and alarm output.
Protection Internal fuse is easily accessible by removing cover. MOV and surge capacitors protect power input. MOV and surge capacitors protect alarm contact outputs. Capacitors and low-voltage MOVs protect power outputs. Back diodes protect power-fail output transistors.
Date Code 20080530 Instruction Manual SEL-PSM Power Supply Module
8 Factory Assistance
Factory Assistance We appreciate your interest in SEL products and services. If you have questions or comments, please contact us at: Schweitzer Engineering Laboratories, Inc. 2350 NE Hopkins Court Pullman, WA 99163-5603 USA Telephone: +1.509.332.1890 Fax: +1.509.332.7990 Internet: www.selinc.com Email: info@selinc.com
All brand or product names appearing in this document are the trademark or registered SCHWEITZER ENGINEERING LABORATORIES 2350 NE Hopkins Court • Pullman, WA 99163-5603 USA trademark of their respective holders. No SEL trademarks may be used without written permission. SEL products appearing in this document may be covered by US and Foreign Phone: +1.509.332.1890 • Fax: +1.509.332.7990 patents. Internet: www.selinc.com • E-mail: info@selinc.com
Schweitzer Engineering Laboratories, Inc. reserves all rights and benefits afforded under federal and international copyright and patent laws in its products, including without lim- itation software, firmware, and documentation. The information in this document is provided for informational use only and is subject to change without notice. Schweitzer Engineering Laboratories, Inc. has approved only the English language document. This product is covered by the standard SEL 10-year warranty. For warranty details, visit www.selinc.com or contact your customer service representative. *PMPSM-01* SEL-PSM Power Supply Module Instruction Manual Date Code 20080530
