2/2•3/2•4/2

Intrinsically Safe & 5/2•5/3

4
Non-Incendive Field Wiring Valves SERIES
Aluminum, Brass, or Stainless Steel Bodies IS &
1/4" to 1" NPT NIFW

Features
• Available in 4 different coil terminations % # )
• H Class coil construction
• Designed solely for installation in intrinsically safe
or NIFW areas, with properly approved and sized
limiting barriers
• Compatible with supervisory current applications
• Mountable in any position

Enclosure Ratings
Catalog Enclosure Enclosure
Prefix Description Type Rating IP Rating
4, 4X IP66
IS 1/2" NPT Conduit
6, 6P IP67
Aluminum Junction Box 4, 4X IP66
JPIS
with 1/2" NPT Conduit 6, 6P IP67

SPECIAL SERVICE
316L Stainless Steel Junction Box 4, 4X IP66
JSIS
with 1/2" NPT Conduit 6, 6P IP67

PILOT
ISVT 5-Pin (Male M12) NA IP20 24VDC Spare Coil Part Number
IS 298006-002-D*
ISSC DIN (Form A) NA IP20
ISSC, JPIS, JSIS 298008-002-*
ISVT 272401-047-*
Valve Construction
Valve Parts in Contact with Fluids
Body Aluminum Brass Stainless Steel Ordering Information
Seals and Discs PUR, NBR Example:
Sleeve 430 Stainless Steel With Aluminum Junction Box – JPIS8314B300
Core and Plugnut 430F Stainless Steel With 316L Stainless Steel Junction Box – JSIS8314B300
Core Springs 302 Stainless Steel
With Conduit – IS8314B300
Pilot Seat Insert (Series 8316 & 8344 only) POM
Rider Rings PTFE
With Quick Disconnect – ISVT8314B300
Spring Retainer POM With DIN Connection – ISSC8314B300
(Connector not included)

Electrical Approvals
Nominal voltage before the barrier – 24VDC +/- 10%. FM and CSA approved for IS - Class I, Div. 1 & 2,
IMPORTANT: Maximum allowable "Off" state leakage current or supervisory Groups A, B, C, and D; Class II, Groups E, F, and G.
current is 4.0 mA. Approved for NIFW - Class I, Div. 2
FM (US & Canada) approved under 3037789 & 3037789C
Iloop - Loop current in the circuit, which may be
CSA certified under File 13976, Class 3228-01
calculated as follows:
(Certificate 1099243)
Vsupply
Iloop = ATEX Approved for:
(Rcoil + Rloop + Rbarrier) II 1 G Ex ia IIC T6 Ga under FM10ATEX0015X
Where: Rcoil - The resistance of the solenoid coil at IECEx Approved for:
Tambient in degrees C Ex ia IIC T6 Ga under IECExFMG10.0008X
Meets applicable CE directives.
Rcoil = 320 ohms x (Tambient + 234)
Refer to Engineering Section for details.
254
Rloop - Resistance of the lead wires
Rbarrier - Internal resistance of the barrier
Entity Parameters
Vmax = 32 VDC Ci = 0 nF
Vsupply - Supply voltage
Imax = 500 mA Li = 0 mH
This current must always be greater than or equal to 0.030 amps Pi = 1.5 W
for proper operation of the solenoid valve.

145
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW
Nominal Ambient Temp. Ranges
Series Body Material Normal Temperature Range Important
8553 Stainless Steel These solenoid valves are intended for use on clean
-40°F to 140°F (-40°C to 60°C)
8551 Brass dry air or inert gas, filtered to 40 micrometres or bet-
8553 -13°F to 140°F (-25°C to 60°C) ter. The dew point of the media should be at least 10°C
Aluminum
8551 5°F to 140°F (-15°C to 60°C) (18° F) below the minimum temperature to which any
8551 Stainless Steel portion of the clean air/inert gas system could be
8262 exposed to prevent freezing. If lubricated air is used,
-40°F to 149°F (-40°C to 65°C) the lubricants must be compatible with Nitrile elas-
8314
8317 Brass / Stainless Steel tomers. Diester oils may cause operational problems.
8316* -20°F to 149°F (-29°C to 65°C) Instrument air in compliance with ANSI/ISA Standard
8223 7.0.01-1996 exceeds the above requirements and is,
8344 -4°F to 149°F (-20°C to 65°C) therefore, an acceptable media for these valves.
Brass only
8316H334
*Does not include JPIS8316B334; Includes JPIS8316B374. Note: 8553 not available in brass

Specifications (English units)

Operating Pressure
Cv Flow Differential (psi)
SPECIAL SERVICE

Max.
Pipe Orifice Factor Air-Inert Gas Fluid and Brass Body Stainless Steel Body
Size Size Pressure to Cylinder to Ambient Const. Const.
PILOT

(in) (in) Cylinder Exhaust Min. Max. Temp. °F Catalog Number Ref. Catalog Number Ref.
2/2 VALVES, NORMALLY CLOSED, with NBR Disc
1/4 1/16 .06 0 130 149 JPIS8262B320 1 JSIS8262B386 1
3/8 5/16 1.5 10 130 149 JPIS8223B323 2 - -
1/2 3/8 3.2 25 130 149 JPIS8223B303 3 JSIS8223B310 3
3/2 VALVES, UNIVERSAL OPERATION (Normally Closed or Normally Open) with NBR Disc – SIL 3 Capable, Certified by Exida

1/4 1/20 .06 .06 0 130/105  149 JPIS8314B300 4 JSIS8314B301 5
3/2 VALVES, NORMALLY CLOSED (Closed when de-energized) with NBR Disc or FKM (Suffix V), as Listed – SIL 3 Capable, Certified by Exida 
1/4 5/16 1.5 1.5  130 149 JPIS8316B301  6 JSIS8316B381 6
3/8 5/16 1.8 1.8  130 149 JPIS8316B302  6 JSIS8316B382 6
3/8 5/8 4 4  130 149 JPIS8316B303  6 - -
1/2 5/8 4 4  130 149 JPIS8316B304  6 JSIS8316B384 6
3/4 11/16 5.5 5.5 10 130 149 JPIS8316B374  7 - -
1 1 13 13 10 130 JPIS8316B334 
149 8 - -
3/2 VALVES, UNIVERSAL (Normally Closed or Normally Open) "Quick Exhaust" with NBR Diaphragm and NBR Disc
1/4  .06 .73 5 130 149 JPIS8317B307  9 JSIS8317B308  10
4/2 VALVES, Brass Body with NBR Disc
Operating Pressure
Cv Flow Differential (psi)
Max.
Pipe Orifice Factor Air-Inert Gas Fluid and Single Solenoid Dual Solenoid
Size Size Pressure to Cylinder to Ambient Const. Const.
(in) (in) Cylinder Exhaust Min. Max. Temp. °F Catalog Number Ref. Catalog Number Ref.
1/4 1/4 .80 1 10 130 149 JPIS8344B370  11 JPIS8344B344  12
3/8 3/8 1.5 2.2 10 130 149 JPIS8344B372  13 JPIS8344B380  14
1/2 3/8 1.5 2.2 10 130 149 JPIS8344B374  13 JPIS8344B382  14
3/4 3/4 5.2 5.6 10 130 149 JPIS8344B376  15 JPIS8344B354  16
1 3/4 5.2 5.6 10 130 149 JPIS8344B378  15 JPIS8344B356  16
 There are two exhaust flows in the exhaust mode (pilot and main). The pilot exhaust must be connected to the main exhaust when the air or inert gas cannot be exhausted to atmosphere.
 For "Quick Exhaust" valves, pressure port is 1/20", exhaust port is 1/4".
 IMPORTANT: A Minimum Operating Pressure Differential must be maintained between the pressure and exhaust ports. Supply and exhaust piping must be full area, unrestricted.
ASCO flow controls and other similar components must be installed in the cylinder lines only.
 Zero minimum when valve selection gasket is in external position and proper auxiliary air pressure is applied. Minimum 15 psi Operating Pressure Differential when selection gasket
is in the internal position.
 Normally closed = 130 psi / Normally open = 105 psi.

Safety manual and FMEDA (Failure Modes Effects and Diagnostic Analysis) report available.
 SIL 3 Capable per IEC 61508, Certified by Exida, only valid when used as Normally Closed.
 Dual solenoid 8344 requires minimum pressure of 20 psi. Single solenoid version has 10 psi minimum pressure requirement.

146
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Specifications (English units)

Single Solenoid – SIL 3 Capable, Certified by Exida  Dual Solenoid
Operating Pressure Operating Pressure
Differential (psi) Differential (psi)
Pipe Orifice Cv Max. Max.
Air-Inert Gas Air-Inert Gas
Body Size Size Flow Fluid Catalog Const. Fluid Catalog Const.
Material (in) (in) Factor Min. Max. Temp.˚F Number Ref. Min. Max. Temp.˚F Number Ref.
3/2, 5/2, 5/3 VALVES, with NBR and PUR Seals
Aluminum 3/2 JPIS8551B305 17 JPIS8551B306 17
Aluminum 5/2 JPIS8551B317 18 JPIS8551B318 18
Aluminum 5/3 Center Closed - - JPIS8551B367 18
Aluminum 5/3 Center Open - - JPIS8551B368 18
1/4 1/4 .86
Brass 3/2 JPIS8551B307 17 JPIS8551B308 17
Brass 5/2 JPIS8551B319 18 JPIS8551B320 18
35 130 149 30 130 149
316L Stainless Steel 3/2 JPIS8551B313 17 JPIS8551B314 17
316L Stainless Steel 5/2 JPIS8551B321 18 JPIS8551B322 18
Aluminum 3/2 JPIS8553B305 17 JPIS8553B306 17
Aluminum 5/2 JPIS8553B317 18 JPIS8553B318 18
1/2 1/2 3.7
316L Stainless Steel 3/2 JPIS8553B313 17 JPIS8553B314 17

SPECIAL SERVICE
316L Stainless Steel 5/2 JPIS8553B321 18 JPIS8553B322 18
 Safety manual and FMEDA (Failure Modes Effects and Diagnostic Analysis) report available.

PILOT
Single Solenoid – SIL 3 Capable, Certified by Exida  Dual Solenoid
Operating Pressure Operating Pressure
Differential (psi) Differential (psi)
Pipe Orifice Cv Max. Max.
Air-Inert Gas Air-Inert Gas
Body Size Size Flow Fluid Catalog Const. Fluid Catalog Const.
Material (in) (in) Factor Min. Max. Temp.˚F Number Ref. Min. Max. Temp.˚F Number Ref.
3/2, 5/2, 5/3 VALVES, with NBR and PUR Seals, NAMUR Mount
Aluminum 3/2, 5/2 JPIS8551B301  19 JPIS8551B302  19
Aluminum 5/3 Center Closed - - JPIS8551B365 20
Aluminum 5/3 Center Open 1/4 1/4 .86 - - JPIS8551B366 20
Brass 3/2, 5/2 35 130 149 JPIS8551B303  19 30 130 149 JPIS8551B304  19
316L Stainless Steel 3/2, 5/2 JPIS8551B309 20 JPIS8551B310 20
Aluminum 3/2, 5/2 JPIS8553B301 20 JPIS8553B302 20
1/2 1/2 3.7
316L Stainless Steel 3/2, 5/2 JPIS8553B309 20 JPIS8553B310 20
 1/8" NPT exhaust for 1/4" aluminum and brass.
 Safety manual and FMEDA (Failure Modes Effects and Diagnostic Analysis) report available.

147
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Specifications (Metric units)

Operating Pressure
Kv Flow Differential (bar)
Max.
Pipe Orifice Factor (m3/h) Air-Inert Gas Fluid and Brass Body Stainless Steel Body
Size Size Pressure to Cylinder to Ambient Const. Const.
(in) (mm) Cylinder Exhaust Min. Max. Temp. °C Catalog Number Ref. Catalog Number Ref.
2/2 VALVES, NORMALLY CLOSED, with NBR Disc
1/4 1.3 .07 0 9 65 JPIS8262B320 1 JSIS8262B386 1
3/8 8 1.3 0.7 9 65 JPIS8223B323 2 - -
1/2 10 2.7 1.7 9 65 JPIS8223B303 3 JSIS8223B310 3
3/2 VALVES, UNIVERSAL OPERATION (Normally Closed or Normally Open) with NBR Disc – SIL 3 Capable, Certified by Exida

1/4 1.3 .05 .05 0 9/7  65 JPIS8314B300 4 JSIS8314B301 5
3/2 VALVES, NORMALLY CLOSED (Closed when de-energized) with NBR Disc – SIL 3 Capable, Certified by Exida 
1/4 8 1.3 1.3  9 65 JPIS8316B301  6 JSIS8316B381 6
3/8 8 1.6 1.6  9 65 JPIS8316B302  6 JSIS8316B382 6
3/8 16 3.5 3.5  9 65 JPIS8316B303  6 - -
1/2 16 3.5 3.5  9 65 JPIS8316B304  6 JSIS8316B384 6
3/4 17 4.7 4.7 0.7 9 65 JPIS8316B374  7 - -
1 25 11.2 11.2 0.7 9 JPIS8316B334 
65 8 - -
SPECIAL SERVICE

3/2 VALVES, UNIVERSAL (Normally Closed or Normally Open) "Quick Exhaust" with NBR Diaphragm and NBR Disc
1/4  .07 .63 0.3 9 65 JPIS8317B307  9 JSIS8317B308  10
PILOT

4/2 VALVES, Brass Body with NBR Disc

Operating Pressure
Kv Flow Differential (bar)
Factor (m3/h) Air-Inert Gas Max. Single Solenoid Dual Solenoid
Pipe Orifice Fluid and
Size Size Pressure to Cylinder to Ambient Const. Const.
(in) (mm) Cylinder Exhaust Min. Max. Temp. °C Catalog Number Ref. Catalog Number Ref.
1/4 6 .69 .86 0.7 9 65 JPIS8344B370  11 JPIS8344B344  12
3/8 10 1.3 1.9 0.7 9 65 JPIS8344B372  13 JPIS8344B380  14
1/2 10 1.3 1.9 0.7 9 65 JPIS8344B374  13 JPIS8344B382  14
3/4 19 4.5 4.8 0.7 9 65 JPIS8344B376  15 JPIS8344B354  16
1 19 4.5 4.8 0.7 9 65 JPIS8344B378  15 JPIS8344B356  16
 There are two exhaust flows in the exhaust mode (pilot and main). The pilot exhaust must be connected to the main exhaust when the air or inert gas cannot be exhausted to atmosphere.
 For "Quick Exhaust" valves, pressure port is 1.3 mm, exhaust port is 6.4 mm.
 IMPORTANT: A Minimum Operating Pressure Differential must be maintained between the pressure and exhaust ports. Supply and exhaust piping must be full area, unrestricted.
ASCO flow controls and other similar components must be installed in the cylinder lines only.
 Zero minimum when valve selection gasket is in external position and proper auxiliary air pressure is applied. Minimum 1.0 bar Operating Pressure Differential when selection gasket
is in the internal position.
 Normally closed = 9 bar / Normally open = 7 bar.

Safety manual and FMEDA (Failure Modes Effects and Diagnostic Analysis) report available.
 SIL 3 Capable per IEC 61508, Certified by Exida, only valid when used as Normally Closed.
 Dual solenoid 8344 requires minimum pressure of 1.4 bar. Single solenoid version has 0.7 bar minimum pressure requirement.

148
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Specifications (Metric units)

Single Solenoid – SIL 3 Capable, Certified by Exida  Dual Solenoid
Operating Pressure Operating Pressure
Differential (bar) Differential (bar)
Pipe Orifice Kv Flow Max. Max.
Air-Inert Gas Air-Inert Gas
Body Size Size Factor Fluid Catalog Const. Fluid Catalog Const.
Material (in) (mm) (m3/h) Min. Max. Temp.˚C Number Ref. Min. Max. Temp.˚C Number Ref.
3/2, 5/2, 5/3 VALVES, with NBR and PUR Seals
Aluminum 3/2 JPIS8551B305 17 JPIS8551B306 17
Aluminum 5/2 JPIS8551B317 18 JPIS8551B318 18
Aluminum 5/3 Center Closed - - JPIS8551B367 18
Aluminum 5/3 Center Open - - JPIS8551B368 18
1/4 6 .74
Brass 3/2 JPIS8551B307 17 JPIS8551B308 17
Brass 5/2 JPIS8551B319 18 JPIS8551B320 18
2.4 9 65 2 9 65
316L Stainless Steel 3/2 JPIS8551B313 17 JPIS8551B314 17
316L Stainless Steel 5/2 JPIS8551B321 18 JPIS8551B322 18
Aluminum 3/2 JPIS8553B305 17 JPIS8553B306 17
Aluminum 5/2 JPIS8553B317 18 JPIS8553B318 18
1/2 13 3.2
316L Stainless Steel 3/2 JPIS8553B313 17 JPIS8553B314 17

SPECIAL SERVICE
316L Stainless Steel 5/2 JPIS8553B321 18 JPIS8553B322 18
 Safety manual and FMEDA (Failure Modes Effects and Diagnostic Analysis) report available.

PILOT
Single Solenoid – SIL 3 Capable, Certified by Exida  Dual Solenoid
Operating Pressure Operating Pressure
Differential (bar) Differential (bar)
Pipe Orifice Kv Flow Max. Max.
Air-Inert Gas Air-Inert Gas
Body Size Size Factor Fluid Catalog Const. Fluid Catalog Const.
Material (in) (mm) (m3/h) Min. Max. Temp.˚C Number Ref. Min. Max. Temp.˚C Number Ref.
3/2, 5/2, 5/3 VALVES, with NBR and PUR Seals, NAMUR Mount
Aluminum 3/2, 5/2 JPIS8551B301  19 JPIS8551B302  19
Aluminum 5/3 Center Closed - - JPIS8551B365 20
Aluminum 5/3 Center Open 1/4 6 .74 - - JPIS8551B366 20
Brass 3/2, 5/2 2.4 9 65 JPIS8551B303  19 2 9 65 JPIS8551B304  19
316L Stainless Steel 3/2, 5/2 JPIS8551B309 20 JPIS8551B310 20
Aluminum 3/2, 5/2 JPIS8553B301 20 JPIS8553B302 20
1/2 13 3.2
316L Stainless Steel 3/2, 5/2 JPIS8553B309 20 JPIS8553B310 20
 1/8" NPT exhaust for 1/4" aluminum and brass.
 Safety manual and FMEDA (Failure Modes Effects and Diagnostic Analysis) report available.

149
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

JUNCTION BOX CONDUIT

2.23 [57]

1.95 [50] 1.68 [43]

1.95 [50]

2.04 [52]

4.46 [113] 3.13 [79]

3.47 [88]
SPECIAL SERVICE

1/2 NPT
PILOT

1.54 [39] 1/2 NPT 1.54 [39]

DIN MULTIPIN
1.89 [48]

1.95 [50]
1.95 [50]

3.58 [91]
3.36 [85]
2.58 [66]
2.36 [60]

.47 [12]
1.54 [39]
1.54 [39]
M12 x 1 THREAD

150
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Const. Ref. 1

4.46 [113]
1.95 [50]

3.47 [88]

2.98 [76]

1.58 [40] 3.34 [85]

1/2 NPT

ANPT
2 PLACES

SPECIAL SERVICE
.34 [9]
.87 [22]

PILOT
.87 [22]

M5 THREAD
7.6[.30] MIN.FULL THREAD DEPTH
2 HOLES FOR MOUNTING

Const. Ref. 2

4.46 [113]
1.95 [50]

3.47 [88]

3.61 [92]

3.08 [78]

1.68 [43]
1/2 NPT IN
3/8

OUTLET
3/8 ANPT

2.44 [62] .75 [19] .94 [24]

INLET 1.25 [32]

3/8 ANPT

151
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Const. Ref. 3

4.46 [113]
1.95 [50]

3.47 [88]

3.33 [85]

1/2 NPT 4.52 [115]

1.93 [49]

OUTLET
1/2 ANPT
SPECIAL SERVICE
PILOT

1.12 [28] INLET

1/2 ANPT

3.03 [77]

3.28 [83]

Const. Ref. 4, 5

4.46 [113]
1.95 [50]
3.47 [88]

1/8 NPT .45 [11]

3.35 [85]

3.71 [94]

1.58 [40]
1/2 NPT
1 2

ANPT
3 PLACES

1.56 [40]

.34 [9]
.87 [22]

.87 [22]

M5 THREAD
7.6[.30] MIN.FULL THREAD DEPTH
2 HOLES FOR MOUNTING

152
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Catalog Number A B C F H K L M N P R S W
in .84 4.68 2.08 5.41 5.01 2.47 2.60 1.06 1.28 4.23 4.06 5.16 3.26
JPIS8316B301, 302
mm 21 119 53 137 127 63 52 27 33 108 103 131 83
in 1.19 4.88 2.18 5.90 5.40 2.72 2.72 1.24 1.32 4.48 4.26 5.36 3.59
JPIS8316B303, 304
mm 30 124 56 150 137 69 69 31 34 114 108 136 91
in 1.00 4.71 1.98 5.57 5.17 2.47 2.06 1.08 1.28 4.24 4.09 5.19 3.28
JPIS8316B381, 382
mm 25 120 50 141 131 63 52 27 33 108 104 132 83
in 1.11 4.88 2.18 5.98 5.48 2.58 2.72 1.24 1.32 4.34 4.26 5.37 3.59
JPIS8316B384
mm 28 124 55 152 139 66 69 31 34 110 108 136 91

Const. Ref. 6

4.46
1.95 [113]
[50]
3.47

SPECIAL SERVICE
[88]

PILOT
1/2 NPT

F H
K

L
N M

C
Ø28 [7]
(4 PLACES)

153
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Const. Ref. 7, 8
4.46 [113] 1.95 [50]
3.47 [88] .45 [11]
1/8 NPT

1/2 NPT

H K

PRESS "P"
SPECIAL SERVICE

4.44 [113]
M 3/4 ANPT
L 3 PLACES
PILOT

W
B N
EXH
"E" OPTIONAL MOUNTING
BRACKET WITH
Ø.28 [Ø7] HOLES
(4 PLACES) AVAILABLE Const.
1.66 [42] ON 3/4 SIZE ONLY Ref. A B C H K L M N P R W
P in 1.61 1.41 1.66 6.78 3.31 3.38 2.16 .53 5.09 .50 3.31
7
mm 41 36 42 172 84 86 55 13 129 13 84
in 2.06 1.78 - 7.40 3.56 4.44 2.70 .87 5.34 1.74 5.31
8
mm 52 45 - 188 90 113 69 22 136 44 135

CYL
"A"
C R

3.82 [97]

Const. Ref. 9. 10
4.46 [113]
1.95 [50]
3.47 [88]

1/8 NPT .45 [11]

3.08 [78]

1.32 [33] 3.59 [91]

1/2 NPT
EXH

2 1 .16 [4]

1/4 ANPT
2.05 [52] 3 PLACES
2.00 [51]

.50 [13]

.75 [19]
.25 [6]
2 .20 [5]

1.50 [38]

.56 [14] 1
.75 [19]

154
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Catalog Number A B C D E F G H J K L M N P Q
in 1.88 1.03 2.15 0.72 2.41 3.21 3.13 1.41 1.36 0.72 4.71 4.65 3.70 1.93 2.22
JPIS8344B370
mm 48 26 55 18 61 82 80 36 35 18 120 118 94 49 57
in 2.62 1.50 2.66 1.06 3.12 3.88 3.18 1.86 1.75 0.83 6.06 4.63 3.51 1.75 2.81
JPIS8344B372, 374
mm 67 38 68 27 79 99 81 47 45 21 154 118 89 44 71
in 3.89 2.10 3.53 1.48 3.79 4.69 4.56 2.12 2.49 1.52 8.22 5.41 3.86 2.10 3.38
JPIS8344B376, 378
mm 99 53 90 38 96 119 116 54 63 39 209 137 98 53 86

Const. Ref. 11, 13, 15

D B C

SPECIAL SERVICE
Ø.34 [8.6]
2 HOLES FOR ANPT

PILOT
MOUNTING 3 PLACES
B
A

G 3.47 Q
E
F [88]

P E

K 1/2 ANPT

1.95
[50]

1/2 ANPT

N
M
P

q OF PIPE
CONNECTION

155
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Catalog Number A B C D E F G H J K L M N P Q R
in 1.88 2.16 1.03 0.75 2.41 1.69 4.91 2.61 1.41 0.72 1.36 5.35 3.13 2.36 4.46 2.02
JPIS8344B344
mm 48 55 26 19 61 43 125 66 36 18 35 136 80 60 113 51
in 3.88 3.53 2.09 1.47 3.81 2.12 8.25 4.34 2.12 1.55 2.51 6.03 4.56 2.83 5.47 2.38
JPIS8344B354, 356
mm 99 90 53 37 97 54 210 110 54 39 64 153 116 72 139 60
in 2.62 2.66 1.50 1.06 3.12 1.56 6.06 3.09 1.86 0.83 1.75 5.74 3.18 2.50 4.65 2.11
JPIS8344B380, 382
mm 67 68 38 27 79 40 154 78 47 21 45 146 81 64 118 54

Const. Ref. 12, 14, 16

B
A
ANPT
.34 DIA [Ø8.6] D C 3 PLACES
2 HOLES FOR
MOUNTING
SPECIAL SERVICE

3.46
PILOT

B A [88]

4.46
M [113]

N E

E
P
1" ANPT
K
J

L H

1.95
[50]

SOL 'B'
SOL 'A'

P
Q R

q OF PIPE
CONNECTION
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Series 8551 8553
NPT 1/4 1/2
L1  5.12 (132) 6.00 (153) Const. Ref. 17
L2  6.73 (171) 7.80 (198)
H2 4.38 (111) 4.77 (121)
4.46 [113]
H1 1.10 (28) 1.58 (40) 3.47 [88]
1.95 [50]

W 1.77 (45) 2.85 (72) 1/8 NPT

 Manual override option MH adds .250" (6.4), 3

MS option adds .468" (11.9) to each solenoid endcap.

1/2 NPT

Optional Manual Operators H2

Add Suffix Description
1
Push and turn to lock with flat 3 1
MO
0 2
head screwdriver slot H1

1
Momentary push in with flat
MI 1/8 NPT AUX. PRESSURE PORT

0 2
head screwdriver slot W L1

SPECIAL SERVICE
1 L2

PILOT
MH Momentary push in by hand
0 2

MS 0 2
Push and turn to lock by hand

Series 8551 8553

NPT 1/4 1/2
L1  5.63 (144) 7.06 (180) Const. Ref. 18
L2  7.20 (183) 8.86 (225)
H2 4.38 (111) 4.77 (121)
H1 1.10 (28) 1.58 (40) 4.46 [113]
1.95 [50]
W 1.77 (45) 2.85 (72) 3.47 [88]

 Manual override option MH adds .250" (6.4), 3

1/8 NPT

MS option adds .468" (11.9) to each solenoid endcap.

1/2 NPT
Optional Manual Operators
H2
Add Suffix Description
1
Push and turn to lock with flat
MO 5 1 3

0 2
head screwdriver slot
H1
1
Momentary push in with flat
MI
0 2
head screwdriver slot 1/8 NPT AUX. PRESSURE PORT
W L1
1
L2

MH Momentary push in by hand

0 2

MS 0 2
Push and turn to lock by hand

157
 2/2•3/2•4/2
5/2•5/3

4
SERIES
IS &
NIFW

Dimensions: inches (mm)

Series 8551 (Aluminum, Brass)

Const. Ref. 19
NPT 1/4
L1  4.96 (126) 4.46 [113]
1.95 [50]
L2  6.49 (165) 3.47 [88]

1/8 NPT
H2 4.38 (111) 3

H1 1.57 (40)
1/2 NPT
W 1.77 (45)
H2
 Manual override option MH adds .250" (6.4),
1/8 NPT
MS option adds .468" (11.9) to each solenoid endcap.
3 1

Optional Manual Operators H1

Add Suffix Description

1
Push and turn to lock with flat W 1/8 NPT AUX. PRESSURE PORT 1/4 NPT
MO
0 2
head screwdriver slot L1

L2
1
Momentary push in with flat
MI
0 2
head screwdriver slot 8551 NAMUR Footprint
SPECIAL SERVICE

1
PILOT

MH Momentary push in by hand

0 2

1.26 (32)
2 4

MS 0 2
Push and turn to lock by hand
.95 (24)

Series 8551 (316L SS) 8551 (5/3) 8553

Const. Ref. 20
NPT 1/4 1/4 1/2 4.46 [113]

L1 
1.95 [50]
5.20 (132) - 7.08 (180) 3.47 [88]

L2 
1/8 NPT
6.73 (171) 7.44 (189) 8.85 (225) 3

H2 4.38 (111) 4.38 (111) 4.77 (121)

1/2 NPT
H1 1.57 (40) 1.57 (40) 2.08 (53) (8551) 1/4 NPT
(8553) 1/2 NPT
W 1.77 (45) 1.77 (45) 2.87 (73) H2

 Manual override option MH adds .250" (6.4), 5 1 3

MS option adds .468" (11.9) to each solenoid endcap.
H1

Optional Manual Operators

Add Suffix Description W 1/8 NPT AUX. PRESSURE PORT
1 L1
Push and turn to lock with flat
MO L2
0 2
head screwdriver slot
1
Momentary push in with flat
MI
head screwdriver slot 8553 NAMUR Footprint 8551 NAMUR Footprint
0 2
1
1.26 (32)

MH Momentary push in by hand 2 4

0 2
2 4
1.77 (45)

MS 0 2
Push and turn to lock by hand .95 (24)

1.57 (40)

158