Non-Traditional Machining

NON-TRADITIONAL MACHINING
UNIT -1

INTRODUCTION
LESSON STRUCTURE:
1.1 Definition

1.2 Non traditional machining (ntm) processes characteristics

1.3 Need for development of non-conventional processes

1.4 Differences between conventional and non conventional machining processes

1.5 Selection of process

1.6 Physical parameter of the process

OBJECTIVES
 ii. Identify the characteristics of non traditional machining
 iii. Differentiate between conventional and non traditional machining
 iv. Classify different non traditional machining processes
 v. Identify the need for non traditional machining processes
 Non-Traditional Machining

NON-TRADITIONAL MACHINING

INTRODUCTION

Non-traditional manufacturing processes is defined as a group of processes

that remove excess material by various techniques involving mechanical, thermal,
electrical or chemical energy or combinations of these energies but do not use a sharp
cutting tools as it needs to be used for traditional manufacturing processes.

Extremely hard and brittle materials are difficult to machine by traditional

machining processes such as turning, drilling, shaping and milling. Non-traditional
machining processes, also called advanced manufacturing processes, are employed
where traditional machining processes are not feasible, satisfactory or economical due to
special reasons as outlined below.

 Very hard fragile materials difficult to clamp for traditional machining


 When the workpiece is too flexible or slender

 When the shape of the part is too complex


Several types of non-traditional machining processes have been developed to meet extra
required machining conditions. When these processes are employed properly, they offer
many advantages over non-traditional machining processes. The common non-
traditional machining processes are described in this section.

1.1 Definition:
A machining process is called non-traditional if its material removal
mechanism is basically different than those in the traditional processes, i.e. a different
form of energy (other than the excessive forces exercised by a tool, which is in physical
contact with the work piece) is applied to remove the excess material from the work
surface, or to separate the workpiece into smaller parts.
Non-Traditional Machining

1.2 Non Traditional Machining (NTM) Processes are characterised as

follows:
• Material removal may occur with chip formation or even no chip formation may take
place.
For example in AJM, chips are of microscopic size and in case of Electrochemical
machining material removal occurs due to electrochemical dissolution at atomic level
• In NTM, there may not be a physical tool present. For example in laser jet machining,
machining is carried out by laser beam. However in Electrochemical Machining there is
a physical tool that is very much required for machining
• In NTM, the tool need not be harder than the work piece material. For example, in
EDM, copper is used as the tool material to machine hardened steels.
• Mostly NTM processes do not necessarily use mechanical energy to provide material
removal. They use different energy domains to provide machining. For example, in
USM, AJM, WJM mechanical energy is used to machine material,

1.3 Need for development of Non-Conventional Processes

The strength of steel alloys has increased five folds due to continuous R and D
effort. In aero-space requirement of High strength at elevated temperature with light
weight led to development and use of hard titanium alloys, nimonic alloys, and other
HSTR alloys. The ultimate tensile strength has been improved by as much as 20 times.
Development of cutting tools which has hardness of 80 to 85 HRC which cannot be
machined economically in
conventional methods led to development of non –traditional machining methods.
1.Technologically advanced industries like aerospace, nuclear power, ,wafer
fabrication, automobiles has ever increasing use of High –strength temperature resistant
(HSTR) alloys (having high strength to weight ratio) and other difficult to machine
materials like titanium, SST,nimonics, ceramics and semiconductors. It is no longer
possible to use conventional process to machine these alloys.
2. Production and processing parts of complicated shapes (in HSTR and other
hard to machine alloys) is difficult , time consuming an uneconomical by conventional
methods of machining
Non-Traditional Machining

3. Innovative geometric design of products and components made of new exotic

materials with desired tolerance, surface finish cannot be produced economically by
conventional machining.
4. The following examples are provided where NTM processes are preferred over
the conventional machining process:
♦ Intricate shaped blind hole – e.g. square hole of 15 mmx15 mm with a depth of 30 mm
with a tolerance of 100 microns
♦ Difficult to machine material – e.g. Inconel, Ti-alloys or carbides, Ceramics,
composites , HSTR alloys, satellites etc.,
♦ Low Stress Grinding – Electrochemical Grinding is preferred as compared to
conventional grinding
♦ Deep hole with small hole diameter – e.g. φ 1.5 mm hole with l/d = 20
♦ Machining of composites

1.4 Differences between Conventional and Non-conventional machining

Processes.

Sl Conventional Process Non-Conventional Process

No.
1. The cutting tool and work piece are There is no physical contact between
always in physical contact with the tool and work piece, In some non
relative motion with each other, traditional process tool wear exists.
which results in friction and tool
wear.
2. Material removal rate is limited by NTM can machine difficult to cut and
mechanical properties of work hard to cut materials like
material. titanium,ceramics,nimonics,
SST,composites,semiconducting
materials
Non-Traditional Machining

3. Relative motion between the tool Many NTM are capable of producing
and work is typically rotary or complex 3D shapes and cavities
reciprocating. Thus the shape of
work is limited to circular or flat
shapes. In spite of CNC systems,
production of 3D surfaces is still a
difficult task.
4. Machining of small cavities , slits , Machining of small cavities, slits and
blind holes or through holes are Production of non-circular, micro sized,
difficult large aspect ratio, shall entry angle
holes are easy using NTM
5. Use relative simple and inexpensive Non-traditional processes requires
machinery and readily available expensive tools and equipment as well
cutting tools as skilled labour, which increase the
production cost significantly
6. Capital cost and maintenance cost is Capital cost and maintenance cost is
low high
7. Traditional processes are well Mechanics of Material removal of Some
established and physics of process of NTM process are still under research
is well understood
8. Conventional process mostly uses Most NTM uses energy in direct form
mechanical energy For example : laser, Electron beam in
its direct forms are used in LBM and
EBM respectively
9. Surface finish and tolerances are High surface finish(up to 0.1 micron)
limited by machining inaccuracies and tolerances (25 Microns)can be
achieved
10. High metal removal rate. Low material removal rate.
Non-Traditional Machining

1.5 SELECTION OF PROCESS:

The correct selection of the non-traditional machining methods must be based on the
following aspects.
i) Physical parameters of the process
ii) Shape to be machined
iii) Process capability
iv) Economics of the processes

Physical parameter of the process:

The physical parameters of the different NTM are given in the Table 1.0 which indicates
that PAM and ECM require high power for fast machining. EBM and LBM require high
voltages and require careful handling of equipment. EDM and USM require medium
power . EBM can be used in vacuum and PAM uses oxygen and hydrogen gas.

Shapes cutting capability

The different shapes can be machined by NTM. EBM and LBM are used for micro
drilling and cutting. USM and EDM are useful for cavity sinking and standard hole
drilling. ECM is useful for fine hole drilling and contour machining. PAM can be used
for cutting and AJM is useful for shallow pocketing

Process capability
The process capability of NTM is given in Table 2.0 EDM which achieves higher
accuracy has the lowest specific power requirement. ECM can machine faster and has a
low thermal surface damage depth. USM and AJM have very material removal rates
combined with high tool wear and are used non metal cutting. LBM and EBM are, due to
their high penetration depth can be used for micro drilling, sheet cutting and welding.
CHM is used for manufacture of PCM and other shallow components.
Non-Traditional Machining

1.6 PHYSICAL PARAMETER OF THE PROCESS:

Classification of NTM processes is carried out depending on the nature of energy

used for material removal. The broad classification is given as follows:
1) Mechanical Processes

Abrasive Jet Machining (AJM)

Ultrasonic Machining (USM)
Water Jet Machining (WJM)
2) Electrochemical Processes
Electrochemical Machining (ECM)
Electro Chemical Grinding (ECG)
Electro Jet Drilling (EJD)
3) Electro-Thermal Processes
Electro-discharge machining (EDM)
Laser Jet Machining (LJM)
Electron Beam Machining (EBM)
4) Chemical Processes
Chemical Milling (CHM)
Photochemical Milling (PCM)
Non-Traditional Machining

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001

Self-Assessment Questions
1. What is necessity for unconventional machining processes?
2. How non-traditional machining processes are classified?
3. Enlist the requirement that demands the use of advanced machining process.
4. Why unconventional mechanical machining process is not so effective on soft metals
like aluminium?
Non-Traditional Machining

UNIT-2

ULTRASONIC MACHINING (USM)

LESSON STRUCTURE:
2.1 Introduction
2.2 USM working principle
2.3 USM Machine
2.4 Working of horn as mechanical amplifier of amplitude of
vibration
2.5 Process Variables
2.6 Applications of USM
2.7 Advantages of USM
2.8 Disadvantages of USM

OBJECTIVES:
 Identify major components of USM equipment
 State the working principle of USM equipment
 Describe the basic mechanism of material removal in USM
 Identify the process parameters of USM
 Identify the machining characteristics of USM
 Analyse the effect of process parameters on material removal rate (MRR)
 Develop mathematical model relating MRR with USM parameters
 Draw variation in MRR with different process parameters
Non-Traditional Machining

UNIT-2

ULTRASONIC MACHINING (USM)

2.1 Introduction

USM is mechanical material removal process or an abrasive process used to erode

holes or cavities on hard or brittle workpiece by using shaped tools, high frequency
mechanical motion and an abrasive slurry. USM offers a solution to the expanding need
for machining brittle materials such as single crystals, glasses and polycrystalline
ceramics, and increasing complex operations to provide intricate shapes and workpiece
profiles. It is therefore used extensively in machining hard and brittle materials that are
difficult to machine by traditional manufacturing processes.
Ultrasonic Machining is a non-traditional process, in which abrasives contained in
a slurry are driven against the work by a tool oscillating at low amplitude (25-100 μm)
and high frequency (15-30 KHz):
The process was first developed in 1950s and was originally used for finishing EDM
surfaces.
The basic process is that a ductile and tough tool is pushed against the work with
a constant force. A constant stream of abrasive slurry passes between the tool and the
work (gap is 25-40 μm) to provide abrasives and carry away chips. The majority of the
cutting action comes from an ultrasonic (cyclic) force applied.

The basic components to the cutting action are believed to be,

 brittle fracture caused by impact of abrasive grains due to the tool vibration;

 cavitation induced erosion;

 chemical erosion caused by slurry.





Non-Traditional Machining

2.2 USM working principle

• Material removal primarily occurs due to the indentation of the hard abrasive grits
on the brittle work material.

• Other than this brittle failure of the work material due to indentation some
material removal may occur due to free flowing impact of the abrasives against
the work material and related solid-solid impact erosion,

• Tool’s vibration – indentation by the abrasive grits.

• During indentation, due to Hertzian contact stresses, cracks would develop just
below the contact site, then as indentation progresses the cracks would propagate
due to increase in stress and ultimately lead to brittle fracture of the work material
Non-Traditional Machining

under each individual interaction site between the abrasive grits and the
workpiece.

• The tool material should be such that indentation by the abrasive grits does not
lead to brittle failure.

• Thus the tools are made of tough, strong and ductile materials like steel, stainless
steel and other ductile metallic alloys.

2.3 USM Machine

USM Equipment
Non-Traditional Machining

The basic mechanical structure of an USM is very similar to a drill press.

However, it has additional features to carry out USM of brittle work material. The work
piece is mounted on a vice, which can be located at the desired position under the tool
using a 2 axis table. The table can further be lowered or raised to accommodate work of
different thickness.
The typical elements of an USM are
 Slurry delivery and return system

 Feed mechanism to provide a downward feed force on the tool during machining

 The transducer, which generates the ultrasonic vibration

 The horn or concentrator, which mechanically amplifies the vibration to the
required amplitude of 15 – 50 μm and accommodates the tool at its tip.

2.4 Working of horn as mechanical amplifier of amplitude of vibration

The ultrasonic vibrations are produced by the transducer. The transducer is driven
by suitable signal generator followed by power amplifier.
The transducer for USM works on the following principle
• Piezoelectric effect
• Magnetostrictive effect
• Electrostrictive effect
Non-Traditional Machining

Magnetostrictive transducers are most popular and robust amongst all. Figure shows a
typical magnetostrictive transducer along with horn. The horn or concentrator is a wave
guide, which amplifies and concentrates the vibration to the tool from the transducer.

The horn or concentrator can be of different shape like

• Tapered or conical
• Exponential
• Stepped

Machining of tapered or stepped horn is much easier as compared to the exponential one.
Figure shows different horns used in USM

2.5 PROCESS VARIABLES:

• Amplitude of vibration (ao) – 15 – 50 μm
• Frequency of vibration (f) – 19 – 25 kHz
• Feed force (F) – related to tool dimensions
• Feed pressure (p)
• Abrasive size – 15 μm – 150 μm
Non-Traditional Machining

• Abrasive material – Al2O3

- SiC
- B4C
- Boronsilicarbide
- Diamond
 Flow strength of work material

 Flow strength of the tool material

 Contact area of the tool – A

 Volume concentration of abrasive in water slurry – C

2.6 Applications of USM

• Used for machining hard and brittle metallic alloys, semiconductors, glass,
ceramics, carbides etc.
• Used for machining round, square, irregular shaped holes and surface impressions.
• Machining, wire drawing, punching or small blanking dies.

Figure: A non-round hole made by USM

2.7 Advantage of USM

USM process is a non-thermal, non-chemical, creates no changes in the microstructures,
chemical or physical properties of the workpiece and offers virtually stress free machined
surfaces.
Non-Traditional Machining

The main advantages are;

· Any materials can be machined regardless of their electrical conductivity
· Especially suitable for machining of brittle materials
· Machined parts by USM possess better surface finish and higher structural integrity.
· USM does not produce thermal, electrical and chemical abnormal surface

2.8 Disadvantages of USM

· USM has higher power consumption and lower material-removal rates than traditional
fabrication processes.
· Tool wears fast in USM.
· Machining area and depth is restraint in USM.

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001

Self-Assessment Questions
1. What is ultrasonic machining?
2. What are the advantages of USM?
3. What are the Disadvantages of USM?
4. What are the applications of USM?
5. What is ultrasonic transducer?
6. What are the magnetostrivtive materials employed in USM?
7. What is the purpose of concentrator used in USM?
Non-Traditional Machining

UNIT -3

ABRASIVE JET MACHINING (AJM)

LESSON STRUCTURE:
3.1 Introduction
3.2 Working principle
3.3 AJM Equipment
3.4 Process Parameters and Machining Characteristics
3.4 Applications
3.5 Advantages of abrasive jet cutting
3.6 Limitations of abrasive jet cutting
3.7 Introduction to Water Jet Machining

OBJECTIVES:
 Describe the basic mechanism of material removal in AJM
 Identify major components of AJM equipment
 State the working principle of AJM
 Identify the process parameters of AJM
 Identify the machining characteristics of AJM
 Analyse the effect of process parameters on material removal rate (MRR)
 Draw variation in MRR with different process parameters
Non-Traditional Machining

ABRASIVE JET MACHINING (AJM)

3.1 Introduction

Abrasive water jet cutting is an extended version of water jet cutting; in which the
water jet contains abrasive particles such as silicon carbide or aluminium oxide in order
to increase the material removal rate above that of water jet machining. Almost any type
of material ranging from hard brittle materials such as ceramics, metals and glass to
extremely soft materials such as foam and rubbers can be cut by abrasive water jet
cutting. The narrow cutting stream and computer controlled movement enables this
process to produce parts accurately and efficiently. This machining process is especially
ideal for cutting materials that cannot be cut by laser or thermal cut. Metallic, non-
metallic and advanced composite materials of various thicknesses can be cut by this
process. This process is particularly suitable for heat sensitive materials that cannot be
machined by processes that produce heat while machining.

3.2 Working principle

Non-Traditional Machining

In Abrasive Jet Machining (AJM), abrasive particles are made to impinge on the
work material at a high velocity. The jet of abrasive particles is carried by carrier gas or
air. The high velocity stream of abrasive is generated by converting the pressure energy
of the carrier gas or air to its kinetic energy and hence high velocity jet. The nozzle
directs the abrasive jet in a controlled manner onto the work material, so that the distance
between the nozzle and the work piece and the impingement angle can be set desirably.
The high velocity abrasive particles remove the material by micro-cutting action as well
as brittle fracture of the work material.

3.3 AJM Equipment

In AJM, air is compressed in an air compressor and compressed air at a pressure

of around 5 bar is used as the carrier gas. Figure also shows the other major parts of the
AJM system. Gases like CO2, N2 can also be used as carrier gas which may directly be
issued from a gas cylinder. Generally oxygen is not used as a carrier gas. The carrier gas
Non-Traditional Machining

is first passed through a pressure regulator to obtain the desired working pressure. To
remove any oil vapour or particulate contaminant the same is passed through a series of
filters. Then the carrier gas enters a closed chamber known as the mixing chamber. The
abrasive particles enter the chamber from a hopper through a metallic sieve. The sieve is
constantly vibrated by an electromagnetic shaker. The mass flow rate of abrasive (15
gm/min) entering the chamber depends on the amplitude of vibration of the sieve and its
frequency. The abrasive particles are then carried by the carrier gas to the machining
chamber via an electro-magnetic on-off valve. The machining enclosure is essential to
contain the abrasive and machined particles in a safe and eco-friendly manner. The
machining is carried out as high velocity (200 m/s) abrasive particles are issued from the
nozzle onto a work piece traversing under the jet.

3.4 Process Parameters and Machining Characteristics.

The process parameters are listed below:

• Abrasive

Material – Al2O3 / SiC / glass

beads Shape – irregular / spherical
Size – 10 ~ 50 μm
Mass flow rate – 2 ~ 20 gm/min
• Carrier gas
o Composition – Air, CO2, N2
3
o Density – Air ~ 1.3 kg/m
o Velocity – 500 ~ 700 m/s
o Pressure – 2 ~ 10 bar
o Flow rate – 5 ~ 30 lpm
 Abrasive Jet

Velocity – 100 ~ 300 m/s

Mixing ratio – mass flow ratio of abrasive to gas
Stand-off distance – 0.5 ~ 5 mm

0 0
Impingement Angle – 60 ~ 90
Non-Traditional Machining

• Nozzle
Material – WC / sapphire

Diameter – (Internal) 0.2 ~ 0.8

mm Life – 10 ~ 300 hours
The important machining characteristics in AJM are
3
• The material removal rate (MRR) mm /min or gm/min
• The machining accuracy
• The life of the nozzle

Effect of process parameters MRR

Non-Traditional Machining

Parameters of Abrasive Jet Maching (AJM) are factors that influence its Metal
Removal Rate (MRR). In a machining process, Metal Removal Rate (MRR) is the
volume of metal removed from a given work piece in unit time. The following are some
of the important process parameters of abrasive jet machining:
1. Abrasive mass flow rate
2. Nozzle tip distance
3. Gas Pressure
4. Velocity of abrasive particles
5. Mixing ratio
6. Abrasive grain size

Abrasive mass flow rate:

Mass flow rate of the abrasive particles is a major process parameter that
influences the metal removal rate in abrasive jet machining.

AJM, mass flow rate of the gas (or air) in abrasive jet is inversely proportional to
the mass flow rate of the abrasive particles.

ue to this fact, when continuously increasing the abrasive mass flow rate, Metal
Removal Rate (MRR) first increases to an optimum value (because of increase in number
of abrasive particles hitting the work piece) and then decreases.

However, if the mixing ratio is kept constant, Metal Removal Rate (MRR)
uniformly increases with increase in abrasive mass flow rate.

Nozzle tip distance:

Nozzle Tip Distance (NTD) is the gap provided between the nozzle tip and the
work piece.
Up to a certain limit, Metal Removal Rate (MRR) increases with increase in nozzle tip
distance. After that limit, MRR remains constant to some extent and then decreases.
Non-Traditional Machining

In addition to metal removal rate, nozzle tip distance influences the shape and diameter of
cut.

For optimal performance, a nozzle tip distance of 0.25 to 0.75 mm is provided.

Gas pressure:
ir or gas pressure has a direct impact on metal removal rate.
In abrasive jet machining, metal removal rate is directly proportional to air or gas
pressure.

Velocity of abrasive particles:

Whenever the velocity of abrasive particles is increased, the speed at which the
abrasive particles hit the work piece is increased. Because of this reason, in abrasive jet
machining, metal removal rate increases with increase in velocity of abrasive particles.

Mixing ratio:
Mixing ratio is a ratio that determines the quality of the air-abrasive mixture in
Abrasive Jet Machining (AJM).

It is the ratio between the mass flow rate of abrasive particles and the mass flow rate of
air (or gas).

When mixing ratio is increased continuously, metal removal rate first increases to some
extent and then decreases.

Abrasive grain size:

Size of the abrasive particle determines the speed at which metal is removed.

If smooth and fine surface finish is to be obtained, abrasive particle with small grain size
is used.

If metal has to be removed rapidly, abrasive particle with large grain size is used.
Non-Traditional Machining

3.5 Applications

  jet cutting is highly used in aerospace, automotive and electronics
Abrasive water
industries.
 
 In aerospace industries, parts such as titanium bodies for military aircrafts, engine

components (aluminium, titanium, heat resistant alloys), aluminium  body parts
 and interior cabin parts are made using abrasive water jet cutting.


In automotive industries, parts like interior trim (head liners, trunk liners, door
 panels) and fibre glass body components and bumpers are made by this process.
Similarly, in electronics industries, circuit boards and cable stripping are made by
abrasive water jet cutting.

Figure: Steel gear and rack cut with an abrasive water jet

3.6 Advantages of abrasive water jet cutting


In most of the cases, no secondary finishing required

No cutter induced distortion

Low cutting forces on workpieces

Limited tooling requirements

Little to no cutting burr

Typical finish 125-250 microns

Smaller kerf size reduces material wastages
 Non-Traditional Machining

No heat affected zone

Localises structural changes

No cutter induced metal contamination

Eliminates thermal distortion

No slag or cutting dross

Precise, multi plane cutting of contours, shapes, and bevels of any angle.

3.7 Limitations of abrasive water jet cutting

 Cannot drill flat bottom

 Cannot cut materials that degrades quickly with moisture

 Surface finish degrades at higher cut speeds which are frequently used for rough
cutting.

 The major disadvantages of abrasive water jet cutting are high capital cost and
high

 noise levels during operation.

Non-Traditional Machining
 WATER JET MACHINING (WJM)
3.8 Introduction to Water Jet Machining
brasive water jet cutting is an extended version of water jet cutting; in which the
water jet contains abrasive particles such as silicon carbide or aluminium oxide in order
to increase the material removal rate above that of water jet machining. Almost any type
of material ranging from hard brittle materials such as ceramics, metals and glass to
extremely soft materials such as foam and rubbers can be cut by abrasive water jet
cutting. The narrow cutting stream and computer controlled movement enables this
process to produce parts accurately and efficiently. This machining process is especially
ideal for cutting materials that cannot be cut by laser or thermal cut. Metallic, non-
metallic and advanced composite materials of various thicknesses can be cut by this
process. This process is particularly suitable for heat sensitive materials that cannot be
machined by processes that produce heat while machining.

he schematic of abrasive water jet cutting is shown in Figure which is similar to

water jet cutting apart from some more features underneath the jewel; namely abrasive,
guard and mixing tube. In this process, high velocity water exiting the jewel creates a
vacuum which sucks abrasive from the abrasive line, which mixes with the water in the
mixing tube to form a high velocity beam of abrasives.

Figure: Abrasive water jet machining

Non-Traditional Machining

Applications

Abrasive water jet cutting is highly used in aerospace, automotive and electronics
industries. In aerospace industries, parts such as titanium bodies for military aircrafts,
engine components (aluminium, titanium, heat resistant alloys), aluminium body parts
and interior cabin parts are made using abrasive water jet cutting.

In automotive industries, parts like interior trim (head liners, trunk liners, door
panels) and fibre glass body components and bumpers are made by this process.
Similarly, in electronics industries, circuit boards and cable stripping are made by
abrasive water jet cutting.

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001

Self-Assessment Questions
1. Define AJM?
2. What are the advantages of AJM process?
3. What are the applications of AJM?
4. Write the Disadvantages of AJM process?
5. Give a summary of the abrasive of their application for different operation?
6. What are the Process parameters affecting the MRR in AJM?
7. What are the different types abrasives used in AJM?
8. Reuse of abrasives is not recommended in AJM. Why?
9. What are the properties of water jet machining about effect cutting action?
10. What are the advantages of WJC over conventional cutting methods?
11. What are the applications of WJM?
12. What are the commonly used additives in WJM?
Non-Traditional Machining

ELECTROCHEMICAL MACHINING (ECM)

LESSON STRUCTURE:

4.1 Definition
4.2 Effect of MRR in ECM
4.3 Advantages of ECM
4.4 Limitations of ECM

OBJECTIVES

 Identify electro-chemical machining (ECM) as a particular type of non-tradition

Processes
 Describe the basic working principle of ECM process
 Describe material removal mechanism in ECM
 Identify the process parameters in ECM
 Identify different modules of ECM equipment
Non-Traditional Machining

ELECTROCHEMICAL MACHINING (ECM)

4.1 Introduction

Electrochemical machining (ECM) is a metal-removal process based on the

principle of reverse electroplating. In this process, particles travel from the anodic
material (workpiece) toward the cathodic material (machining tool). A current of
electrolyte fluid carries away the deplated material before it has a chance to reach the
machining tool. The cavity produced is the female mating image of the tool shape.

ECM process

Similar to EDM, the workpiece hardness is not a factor, making ECM suitable for
machining difficult-to –machine materials. Difficult shapes can be made by this process
on materials regardless of their hardness. A schematic representation of ECM process is
shown in Figure 8. The ECM tool is positioned very close to the workpiece and a low
Non-Traditional Machining

voltage, high amperage DC current is passed between the workpiece and electrode. Some
of the shapes made by ECM process is shown in Figure.

4.2 Effect of MRR in ECM

Material removal rate, MRR, in electrochemical machining:

3
MRR = C .I. h (cm /min)
3
C: specific (material) removal rate (e.g., 0.2052 cm /amp-min for nickel);

I: current (amp);

h: current efficiency (90–100%).

The rates at which metal can electrochemically remove are in proportion to the
current passed through the electrolyte and the elapsed time for that operation. Many
factors other than current influence the rate of machining. These involve electrolyte type,
rate of electrolyte flow, and some other process conditions.

Parts made by ECM

Non-Traditional Machining

4.2 Advantages of ECM

 The components are not subject to either thermal or mechanical stress.


 No tool wear during ECM process.

 Fragile parts can be machined easily as there is no stress involved.

 ECM deburring can debur difficult to access areas of parts.

 High surface finish (up to 25 µm in) can be achieved by ECM process.

 Complex geometrical shapes in high-strength materials particularly in the
aerospace industry for the mass production of turbine blades, jet-engine parts and
nozzles can be machined repeatedly and accurately.

 Deep holes can be made by this process.

4.3 Limitations of ECM

 ECM is not suitable to produce sharp square corners or flat bottoms because of
the tendency for the electrolyte to erode away sharp profiles.

 ECM can be applied to most metals but, due to the high equipment costs, is
usually used primarily for highly specialised applications.

Material removal rate, MRR, in electrochemical machining:

3
MRR = C .I. h (cm /min)
3
C: specific (material) removal rate (e.g., 0.2052 cm /amp-min for nickel);

I: current (amp);

h: current efficiency (90–100%).

The rates at which metal can electrochemically remove are in proportion to the current
passed through the electrolyte and the elapsed time for that operation. Many factors other
than current influence the rate of machining. These involve electrolyte type, rate of
electrolyte flow, and some other process conditions.
Non-Traditional Machining

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001

Self-Assessment Questions
1. Define ECM?
2. What are the factors that influence oxidation in ECM?
3. What are the materials used to make the tool electrode?
4. What are the main functions of electrolysis in the ECM?
5. What are the properties are expected from the electrolysis used in the ECM?
6. What are the parameters that affect the MRR?
7. What are the advantages of ECM?
8. What are the limitations of ECM?
9. What are the applications of ECM?
10. Which material is used to make the grinding wheel?
11. What are the advantages of ECG?
12. What are the disadvantages of ECG?
13. What are the limitations of ECG?
14. What is the application of ECG?
Non-Traditional Machining

CHEMICAL MACHINING (CHM)

LESSON STRUCTURE:
5.1 Introduction
5.2 CHEMICAL MILLING
5.3 Steps in chemical milling
5.4 Applications

OBJECTIVES
 Describe the basic working principle of CHM process
 Describe material removal mechanism in CHM
Non-Traditional Machining

CHEMICAL MACHINING (CHM)

5.1 Introduction

Chemical machining (CM) is the controlled dissolution of workpiece material

(etching) by means of a strong chemical reagent (etchant). In CM material is removed
from selected areas of workpiece by immersing it in a chemical reagents or etchants; such
as acids and alkaline solutions. Material is removed by microscopic electrochemical cell
action, as occurs in corrosion or chemical dissolution of a metal. This controlled chemical
dissolution will simultaneously etch all exposed surfaces even though the penetration
rates of the material removal may be only 0.0025–0.1 mm/min. The basic process takes
many forms: chemical milling of pockets, contours, overall metal removal, chemical
blanking for etching through thin sheets; photochemical machining (pcm) for etching by
using of photosensitive resists in microelectronics; chemical or electrochemical polishing
where weak chemical reagents are used (sometimes with remote electric assist) for
polishing or deburring and chemical jet machining where a single chemically active jet is
used. A schematic of chemical machining process is shown in Figure.

(a) Schematic of chemical machining process (b) Stages in producing a profiled cavity
by chemical machining (Kalpakjain & Schmid)
Non-Traditional Machining

5.2 CHEMICAL MILLING

In chemical milling, shallow cavities are produced on plates, sheets, forgings and
extrusions. The two key materials used in chemical milling process are etchant and
maskant. Etchants are acid or alkaline solutions maintained within controlled ranges of
chemical composition and temperature. Maskants are specially designed elastomeric
products that are hand strippable and chemically resistant to the harsh etchants.

5.3 Steps in chemical milling

 Residual stress relieving: If the part to be machined has residual stresses from the
previous processing, these stresses first should be relieved in order to prevent
warping after chemical milling.

 Preparing: The surfaces are degreased and cleaned thoroughly to ensure both
good adhesion of the masking material and the uniform material removal.

 Masking: Masking material is applied (coating or protecting areas not to be
etched).

 Etching: The exposed surfaces are machined chemically with etchants.

 Demasking: After machining, the parts should be washed thoroughly to prevent
further reactions with or exposure to any etchant residues. Then the rest of the
masking material is removed and the part is cleaned and inspected.

5.4 Applications:

Chemical milling is used in the aerospace industry to remove shallow layers of material
from large aircraft components missile skin panels (Figure ), extruded parts for airframes.
Non-Traditional Machining

Figure : Missile skin-panel section contoured by chemical milling to improve the

stiffness- to- weight ratio of the part (Kalpakjain & Schmid)

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001
Non-Traditional Machining

UNIT -6

ELECTRICAL DISCHARGE MACHINING (EDM)

LESSON STRUCTURE:
6.1 Introduction
6.2 Working principle of EDM
6.3 Dielectric fluids
6.4 Wire EDM
6.5 Application of EDM
6.6 Advantages of EDM
6.7 Limitations of EDM

OBJECTIVES
 Identify electro-discharge machining (EDM) as a particular type of non-tradition
Processes
 Describe the basic working principle of EDM process
 Describe material removal mechanism in EDM
 Identify the process parameters in EDM
 Describe the characteristics of EDM
 Identify the purpose of dielectric fluid in EDM
 Identify the machining characteristics in EDM
 Analyse the effect of process variables on surface roughness
Non-Traditional Machining

ELECTRICAL DISCHARGE MACHINING (EDM)

6.1 Introduction

Electrical discharge machining (EDM) is one of the most widely used non-
traditional machining processes. The main attraction of EDM over traditional machining
processes such as metal cutting using different tools and grinding is that this technique
utilises thermoelectric process to erode undesired materials from the workpiece by a
series of discrete electrical sparks between the workpiece and the electrode. A picture of
EDM machine in operation is shown in Figure.

Figure : Electrical discharge machine

The traditional machining processes rely on harder tool or abrasive material to

remove the softer material whereas non-traditional machining processes such as EDM
uses electrical spark or thermal energy to erode unwanted material in order to create
desired shape. So, the hardness of the material is no longer a dominating factor for EDM
process. A schematic of an EDM process is shown in Figure 2, where the tool and the
workpiece are immersed in a dielectric fluid.
Non-Traditional Machining

6.2 Working principle of EDM

As shown in Figure 1, at the beginning of EDM operation, a high voltage is

applied across the narrow gap between the electrode and the workpiece. This high voltage
induces an electric field in the insulating dielectric that is present in narrow gap between
electrode and workpiece. This cause conducting particles suspended in the dielectric to
concentrate at the points of strongest electrical field. When the potential difference
between the electrode and the workpiece is sufficiently high, the dielectric breaks down
and a transient spark discharges through the dielectric fluid, removing small amount of
material from the workpiece surface. The volume of the material removed per spark
-6 -6 3
discharge is typically in the range of 10 to 10 mm .

The material removal rate, MRR, in EDM is calculated by the following foumula:

1.23 3
MRR = 40 I / Tm (cm /min)

Where, I is the current amp,

0
Tm is the melting temperature of workpiece in C

Figure: Schematic of EDM process

Non-Traditional Machining

EDM removes material by discharging an electrical current, normally stored in a

capacitor bank, across a small gap between the tool (cathode) and the workpiece (anode)
typically in the order of 50 volts/10amps.

6.3 Dielectric fluids

Dielectric fluids used in EDM process are hydrocarbon oils, kerosene and
deionised water. The functions of the dielectric fluid are to:

 Act as an insulator between the tool and the workpiece.


 Act as coolant.

 Act as a flushing medium for the removal of the chips.

The electrodes for EDM process usually are made of graphite, brass, copper and copper-
tungsten alloys.

Design considerations for EDM process are as follows:

 Deep slots and narrow openings should be avoided.


 The surface smoothness value should not be specified too fine.

 Rough cut should be done by other machining process. Only finishing operation
should be done in this process as MRR for this process is low.

6.4 Wire EDM

EDM, primarily, exists commercially in the form of die-sinking machines and

wire-cutting machines (Wire EDM). The concept of wire EDM is shown in Figure 4. In
this process, a slowly moving wire travels along a prescribed path and removes material
from the workpiece. Wire EDM uses electro-thermal mechanisms to cut electrically
conductive materials. The material is removed by a series of discrete discharges between
the wire electrode and the workpiece in the presence of dieelectirc fluid, which creates a
path for each discharge as the fluid becomes ionized in the gap. The area where discharge
takes
Non-Traditional Machining

place is heated to extremely high temperature, so that the surface is melted and removed.
The removed particles are flushed away by the flowing dielectric fluids.

The wire EDM process can cut intricate components for the electric and aerospace
industries. This non-traditional machining process is widely used to pattern tool steel for
die manufacturing.

Wire erosion of an extrusion die

The wires for wire EDM is made of brass, copper, tungsten, molybdenum. Zinc or
brass coated wires are also used extensively in this process. The wire used in this process
should posses high tensile strength and good electrical conductivity. Wire EDM can also
employ to cut cylindrical objects with high precision. The sparked eroded extrusion dies
are presented in Figure.
Non-Traditional Machining

Sparked eroded extrusion dies

This process is usually used in conjunction with CNC and will only work when a
part is to be cut completely through. The melting temperature of the parts to be machined
is an important parameter for this process rather than strength or hardness. The surface
quality and MRR of the machined surface by wire EDM will depend on different
machining parameters such as applied peak current, and wire materials.

6.5 Application of EDM

The EDM process has the ability to machine hard, difficult-to-machine materials.
Parts with complex, precise and irregular shapes for forging, press tools, extrusion dies,
difficult internal shapes for aerospace and medical applications can be made by EDM
process. Some of the shapes made by EDM process are shown in Figure.
Non-Traditional Machining

Figure: Difficult internal parts made by EDM process

6.6 Advantages of EDM

The main advantages of DM are:

 By this process, materials of any hardness can be machined;


 No burrs are left in machined surface;

 One of the main advantages of this process is that thin and fragile/brittle
components can be machined without distortion;

 Complex internal shapes can be machined

6.7 Limitations of EDM

The main limitations of this process are:

 This process can only be employed in electrically conductive materials;


 Material removal rate is low and the process overall is slow compared to
conventional machining processes;

 Unwanted erosion and over cutting of material can occur;

Non-Traditional Machining

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001

Self-Assessment Questions
1. Define electrical discharge machining?
2. What are functions of dielectric fluid used in EDM?
3. Basic requirement of dielectric fluid used in EDM?
4. What the dielectric fluids commonly used in EDM?
5. Name some of the tool material used in EDM?
6. What is the process parameter efficiency the MRR?
7. Explain electrode wear?
8. What are types of power supply circuits used in EDM?
9. What are the design factors to be considered while selecting the machine tool?
Non-Traditional Machining

UNIT -7

LASER BEAM MACHINING (LBM)

LESSON STRUCTURE:

7.1 Introduction
7.2 Laser beam cutting (drilling)
7.3 Laser beam cutting (milling)
7.4 Advantage of laser cutting
7.5 Limitations of laser cutting

OBJECTIVES:
 Describe the basic mechanism of material removal in LBM
 Identify major components of LBM equipment
 State the working principle of LBM equipment
 Identify the machining characteristics of LBM
Non-Traditional Machining

LASER–BEAM MACHINING (LBM)

7.1 Introduction

Laser-beam machining is a thermal material-removal process that utilizes a high-

energy, coherent light beam to melt and vaporize particles on the surface of metallic and
non-metallic workpieces. Lasers can be used to cut, drill, weld and mark. LBM is
particularly suitable for making accurately placed holes. A schematic of laser beam
machining is shown in Figure.

Different types of lasers are available for manufacturing operations which are as follows:

 CO2 (pulsed or continuous wave): It is a gas laser that emits light in the infrared
region. It can provide up to 25 kW in continuous-wave mode.

 Nd:YAG: Neodymium-doped Yttrium-Aluminum-Garnet (Y3Al5O12) laser is a
solid-state laser which can deliver light through a fibre-optic cable. It can provide
up to 50 kW power in pulsed mode and 1 kW in continuous-wave mode.

Figure: Laser beam machining schematic

Non-Traditional Machining

7.2 Laser beam cutting (drilling)

 In drilling, energy transferred (e.g., via a Nd:YAG laser) into the workpiece melts
the material at the point of contact, which subsequently changes into a plasma and
leaves the region.

 A gas jet (typically, oxygen) can further facilitate this phase transformation and
departure of material removed.

 Laser drilling should be targeted for hard materials and hole geometries that are
difficult to achieve with other methods.

A typical SEM micrograph hole drilled by laser beam machining process

employed in making a hole is shown in Figure

rd
Figure: SEM micrograph hole drilled in 250 micro meter thick Silicon Nitride with 3
harmonic Nd: YAG laser

7.3 Laser beam cutting (milling)

 A laser spot reflected onto the surface of a workpiece travels along a prescribed
trajectory and cuts into the material.

 Continuous-wave mode (CO2) gas lasers are very suitable for laser cutting
providing high-average power, yielding high material-removal rates, and
smooth cutting surfaces.
Non-Traditional Machining

7.4 Advantage of laser cutting

 No limit to cutting path as the laser point can move any path.

 The process is stress less allowing very fragile materials to be laser cut without
any support.

 Very hard and abrasive material can be cut.

 Sticky materials are also can be cut by this process.

 It is a cost effective and flexible process.

 High accuracy parts can be machined.

 No cutting lubricants required

 No tool wear

 Narrow heat effected zone

7.5 Limitations of laser cutting

 Uneconomic on high volumes compared to stamping


 Limitations on thickness due to taper

 High capital cost

 High maintenance cost

 Assist or cover gas required

FURTHER READING:
1. Modern machining process, Pandey and Shah, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000
3. Production Technology, HMT Tata McGraw Hill. 2001

Self-Assessment Questions
1. What is Laser?
2. What are the characteristics of Laser beam?
3. What are the gases commonly used in LASER?
4. What are the characteristics of Laser used in Laser machining?