Service Manual: LCD Colour Television

TopPage
LC-32LE240M/340M(1stEdition)
SERVICE MANUAL
No. SY1V132LE340M
LCD COLOUR TELEVISION
LC-32LE240M
MODELS LC-32LE340M
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION CHAPTER 5. TROUBLESHOOTING TABLE
IMPORTANT SERVICE SAFETY PRE- [1] TROUBLESHOOTING TABLE ......................5-1
CAUTION ............................................................i
PRECAUTIONS FOR USING LEAD-FREE CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM
SOLDER ............................................................ii [1] OVERALL WIRING DIAGRAM......................6-1
[2] SYSTEM BLOCK DIAGRAM .........................6-2
OUTLINE
MAJOR SERVICE PARTS ................................ iii CHAPTER 7. PRINTED WIRING BOARD ASSEM-
BLIES
CHAPTER 1. SPECIFICATIONS [1] MAIN Unit ......................................................7-1
[1] SPECIFICATIONS ......................................... 1-1
CHAPTER 8. SCHEMATIC DIAGRAM
CHAPTER 2. OPERATION MANUAL [1] DESCRIPTION OF SCHEMATIC DIA-
[1] OPERATION MANUAL .................................. 2-1 GRAM............................................................8-1
[2] MAIN Unit ......................................................8-2
CHAPTER 3. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS ................... 3-1 Parts Guide
CHAPTER 4. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ....................... 4-1
[2] USB Clone (Smart Loader) ............................ 4-7
[3] PUBLIC MODE SETTING PROCEDURE ........ 4-8
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for

after sales service only.
The contents are subject to change without notice.
Downloaded from www.Manualslib.com manuals search engine

LC32LE240M
SAFETY PRECAUTION Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
WARNING All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
1. For continued safety, no modification of any circuit should be only for the purpose of completing these checks.)
attempted.
Any reading of 0.74 Vrms (this corresponds to 0.5 mA rms AC.) or
2. Disconnect AC power before servicing. more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks: DVM
3. Inspect all lead dress to make certain that leads are not pinched, AC SCALE
and check that hardware is not lodged between the chassis and
other metal parts in the receiver. 1.5k ohm
4. Inspect all protective devices such as non-metallic control knobs, 10W
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current
0.15 µF
in the following manner.
TEST PROBE
• Plug the AC cord directly into a 110-240 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground. TO EXPOSED CONNECT TO
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen- METAL PARTS KNOWN EARTH
GROUND
sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD colour television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder

• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Using lead-free wire solder

• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
ii
LC32LE240M
OUTLINE Service Manual
MAJOR SERVICE PARTS
PWB UNIT
Ref No. Part No. Description

N DUNTKF998FMG4 MAIN Unit (LC-32LE340M)
N DKEYMF998FMG5 MAIN Unit (LC-32LE240M)
N RUNTKA929WJQZ POWER Unit
N RUNTKA927WJZZ LED PWB A
N RUNTKA928WJZZ LED PWB B
OTHER UNIT
Ref No. Part No. Description

N R1LK315T3HB00W LCD Panel Unit
iii
LC32LE240M
CHAPTER 1. SPECIFICATIONS Service Manual
[1] SPECIFICATIONS
Item Model LC-32LE240M LC-32LE340M

Screen size 80 cm
Resolution 1,049,088 pixels (1366 x 768)
Video Color System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV TV-Standard NTSC: M
Function
Receiving VHF/UHF 48.00 — 863.25 MHz
Channel
CATV S1 — S41ch (including Hyperband)
TV-Tuning System Auto Preset 99 ch
STEREO/BILINGUAL MTS: M
Viewing angles H : 176º V : 176º
Audio amplifier/Speakers 5 W x 2 / 3.14 x 14.4 cm 2pcs
Terminals Antenna input UHF/VHF 75 DIN type
INPUT 1 HDMI (HDMI input), AUDIO in ( 3.5 mm jack)
INPUT 2 VIDEO in, AUDIO in
INPUT 3 VIDEO in, AUDIO in, COMPONENT in
INPUT 4 (PC input) 15 pin mini D-sub, AUDIO in (common use with INPUT 1) ( 3.5 mm jack)
AUDIO OUT AUDIO out
USB USB
Headphone 3.5 mm stereo
OSD language English/Simplified Chinese/Arabic/French/Portuguese/Russian/Persian/Thai/
Vietnamese/Indonesian
Power Requirement AC 110 — 240 V, 50/60 Hz
Power Consumption 55 W (0.8 W Standby)
without stand 750 (W) x 478 (H) x 55 (D) mm
Dimensions
with stand 750 (W) x 508 (H) x 222 (D) mm
Weight 7.6 kg (without stand) / 8.5 kg (with stand)
Operating Temperature 0°C — 40°C
• As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
1–1
LC32LE240M
CHAPTER 2. OPERATION MANUAL Service Manual
[1] OPERATION MANUAL
Part names
TV (Front)
Remote control sensor

POWER indicator
Light off Power off.
Lighted (Red) The TV is in standby mode.
Lighted (Green) The TV is on.
TV (Rear)
1 POWER (On/Off) button
2 MENU button
12
3 INPUT button
4 Channel up ( )/down ( ) buttons
5 Volume up (+ ) /down (- ) buttons
13 6 INPUT 1 (HDMI) terminal*
7 INPUT 4 terminal*
8 INPUT 3 terminals
9 AUDIO OUT terminals
10 INPUT 2 terminals
11 Antenna input terminal
11 1
6 12 USB terminal
2 13 Headphone jack ( 3.5 mm)
• The speakers do not output volume
3 when headphones are plugged in.
7
4
8
5
9
10
9 10
* The INPUT 1 and INPUT 4 terminals can both use the same audio input terminal. However, the proper item must be
selected in the "PC audio select" menu.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
• The illustrations used throughout this manual are based on LC-32LE340M.
2–1
Remote control unit

7 VOL+ /VOL -
Set the volume.
1 12 (VOL + ) Increasethe volume.
2 13 (VOL - ) Decreasethe volume.
3
8 (Mute)
4 Press Mutes sound.
Press again Restores sound.
5 14 Mute will be canceled after 30 minutes. However, the TV
6 will not suddenly output loud sound as the volume level will
15 be set to 0 automatically. Increase the volume level by
7
pressing VOL + .
16
8 17 9 / / / (Cursor)
Select a desired item on the setting screen.
9
ENTER
10 18 Execute a command.
11 10 COLOUR ADJ. (FREEZE)
Freeze a motion picture on the screen and adjust the color
tone of the still image.
11 Color (Red/Green/Yellow/Blue)
The colored buttons are correspondingly used to select the
colored items on the screen.
12 ECO
Reduce overall power consumption based on user
1 POWER (STANDBY/ON) preferences.
To switch the power on and off. 13 PHOTO
2 DISPLAY Display your pictures directly on the TV screen.
Display the channel or input information. 14 INPUT (INPUT SOURCE)
3 SLEEP Select an input source.
Set the Sleep timer. 15 CH /CH
0 hr. 30 min. 1 hr. 00 min. 1 hr. 30 min. TV input mode: Select the channel.
(CH ) Increase the channel number.
Off 2 hr. 30 min. 2 hr. 00 min.
(CH ) Decrease the channel number.
4 0…9
Set the channel. 16 MPX
Select the sound multiplex mode.
5 (Flashback)
Press to return to the previous selected channel 17 MENU
or external input mode. Display the menu screen.
6 AV MODE 18 RETURN
Select an audio and video setting. MENU mode: Return to the previous menu screen.
2–2
Attaching the stand

• Before attaching (or detaching) the stand, unplug the AC cord from the AC outlet.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from
being damaged.
1 Confrm the screws supplied with the TV.
Screws (x 4)
(used in step 3)
Soft
cushion
2 Insert the stand base to the stand post on the

bottom of the TV. ( )
3 Insert and tighten the 4 screws into the 4 holes
on the bottom of the stand base. ( )
NOTE Stand Screw
• To detach the stand, perform the steps in reverse order.
CAUTION
Screw driver
• Do not attach or detach the stand without holding it.
Doing so can cause the stand to fall, resulting in serious
personal injuries as well as damage to the stand.
2–3
LC32LE240M
Service
CHAPTER 3. REMOVING OF MAJOR PARTS Manual
[1] REMOVING OF MAJOR PARTS

1. Removing of the Rear Cabinet Ass’y and Stand Base
1. Remove the 4 screws and detach the Stand Base .
2. Remove the 1 screw , 3 screws and 8 screws .
3. Detach the Rear Cabinet Ass’y .
Rear Cabinet Ass'y 6
Stand Base 2
3–1
2. Removing of Connectors
1. Disconnect the following connectors from MAIN Unit. (SP, PD, LW)
2. Disconnect the following connectors from POWER Unit. (PD, LA)
3. Disconnect the following connectors from Panel Ass’y. (LW, LA1, LA2)
Panel Ass'y
[LW]
[LW]
[SP]
[PD]
[PD]
[LA]
[LA1] [LA2]
POWER Unit MAIN Unit
3–2
3. Removing of the Bottom Bracket, MAIN Unit, POWER Unit and Speaker-L/R
1. Remove the 1 screw , 2 screws and detach the Bottom Bracket .
2. Remove the 5 screws and detach the MAIN Unit , Side Cover .
3. Remove the 3 screws and detach the POWER Unit .
4. Detach the Speaker-L/R .
MAIN Unit 6
7
8 POWER Unit
4 Side Cover
3 Bottom
Bracket
2
[SP] 1
Speaker-R 9 Speaker-L 9
3–3
4. Removing of the Chassis Ass’y and LCD Panel Unit
1. Remove the 5 screws and detach the Chassis Ass’y .
2. Detach the LCD Panel Unit .
Chassis Ass'y 2
LCD Panel Unit 3
CAB-A Ass'y
3–4
5. Removing LCD Panel Unit
1. Detach the LED PWB-A , LED PWB-B and Heat Spreader .
2. Detach the Reflection , LGP , Lens sheet V , Lens sheet H and Diffusion Sheet .
3. Remove the 4 screws , 4 screws and detach the bezel Ass’y (Top) (Bottom) (Left) (Right) , , , .
4. Detach the bottom Sheet , Left Sheet and Right Sheet .
5. Detach the LCD Panel Unit from CAB-A .
10
11 Bezel Ass'y (Top)
Bezel Ass'y (Left) 13
9
9
Left Sheet 16
14 Bezel Ass'y (Right)

18 LCD Panel Unit Bezel Ass'y (Bottom) 12
19 CAB-A Ass'y
9
17 Right Sheet
15 Bottom Sheet
Reflection 4
2 LED PWB-B
Lens Sheet V 6
Diffusion Sheet 8
1 LED PWB-A
3 Heat Spreader
5 LGP
7 Lens Sheet H
3–5
LC32LE240M
CHAPTER 4. ADJUSTMENT Service Manual
[1] ADJUSTMENT PROCEDURE

1. Entering and cancel the adjustment process mode
1) While holding down the TV/VIDEO and Volume DOWN keys at the same time, plug in the AC cord to turn on the power. (“K” standing for inspec-
tion process mode is displayed on the upper left position of the screen.)
2) Press the Channel DOWN and Volume DOWN keys at the same time. (The adjustment process mode screen appears.)
3) To cancel it, turn off the power using the Power switch or remote control.
2. Remote controller key operation and description of display in adjustment process mode.
1. key operation
Remote controller key Main unit key Function

CH ( / ) CH ( / ) Changing channel (UP/DOWN)
VOL (+ / –) VOL (+ / –) Changing volume (UP/DOWN)
Cursor ( / ) —————— Turning a page (PREVIOUS/NEXT)
Cursor ( / ) —————— Changing a selected line setting (+10/-10)
TV/VIDEO button on remote TV/VIDEO button Input source switching (toggle switching)
controller (TV-DAV-1/SAV-1 → AV-2 → COMPONENT → HDMI → PC)
ENTER —————— ——————
* Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
3. Software upgrading.
1) Plug off the LCD TV.
2) Insert the USB device to the USB terminal at the LCD TV.
(Make sure that the latest software is installed in the USB device).
3) Hold the LCD TV power key and plug on the LCD TV.
4) LCD TV is on and detecting the USB device.
USB device found
5) A few seconds later, the software upgrading will start automatically.
Do not power off

Chip Programming
4–1
6) Let the process running & entering verification.
Verifying
Verified
7) Software is successfully installed when the following appears at the end of the process.
Please re-boot the system

Update Finished
8) Plug off the LCD TV and plug ON again as usual.

9) LCD TV is running with the latest software.
4. EDID DATA INPUT

4.1. HDMI EDID
Adjustment item Adjustment conditions Adjustment procedure

1 EDID Input Inspection mode 1) EDID data is input to IC1501 (HDMI INPUT1). *1
(HDMI) Confirrm the file name/ver- 2) EDID data is input before HDMI operation checking.(Without EDID data, HDMI will
sion. not function correctry)
4.2. ANALOG PC EDID

1 EDID Input Inspection mode 1) EDID data is input to IC508 (PC INPUT) at checker line. *2
(ANALOG PC) Confirrm the file name/ver- 2) EDID data is input before Analog PC operation checking.
sion.
NOTE: *1 HDMI EDID file name : edid_32LE340_HDMI1_111019.bin

NOTE: *2 PC EDID file name : 32LE340 PC EDID111019.bin
Main Software Package
Model Software Package

32LE340M ORCD_MM_Asia_Pack03_vXXX.bin
32LE240M ORCD_MM_Asia_Pack04_vXXX.bin
Main Software File name : XXX is Software version

If any changes of software, will be informed by MARUHEN.
4–2
5. Signal adjustment
5.1. Picture Adjustment
Confirmation of signal from generator (setting to spec level)
• PAL Composite signal : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

• 15K Component signal (50Hz) : Y level: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
Pb, Pr level: 0.7Vp-p ± 0.02Vp-p
• 33K Component signal : Y level: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
Pb, Pr level: 0.7Vp-p ± 0.02Vp-Com
5.1.1 ADJUSTMENT MODE

1 Adjustment mode 1) Press the test key at the test remote control.
*On double screen models, the tuner, composite signal and component signal sdjustment are made for their single screen mode and double screen
mode as well.
5.1.2 Component 15K 50Hz signal adjustment (COMP-SD)

1 Adjustment [Signal] Feed the COMPONENT 15K 50Hz (576i) 100% Full-field Colour Bar signal (100% colour
COMP 15K 50Hz (576i) saturation) to INPUT 3 COMPONENT terminal.
100% Full-field Colour Bar
[Terminal]
INPUT 3 COMPONENT
100% white Black
2 Auto adjustment Process Mode page 4 1) At the related page, move cursor to [COMP SD ADJ], press ENTER.
performance (COMP SD) 2) [OK] appears when finished.
5.1.3 Component 33K 60Hz signal adjustment (COMP-HD)

1 Adjustment [Signal] Feed the COMPONENT 33K 60Hz (1080i) 100% Full-field Colour Bar signal (100%
COMP 33K 60Hz (1080i) colour saturation) to INPUT 3 COMPONENT terminal.
100% Full-field Colour Bar
[Terminal]
INPUT 3 COMPONENT
100% white Black
2 Auto adjustment Process Mode page 5 1) At the related page, move cursor to [COMP HD ADJ], press ENTER.
performance (COMP HD) 2) [OK] appears when finished.
4–3
5.1.4 PC (ANALOG RGB) signal adjustment (PC-RGB)

1 Adjustment [Signal] Feed the XGA 60Hz 100% Checkered pattern signal (100% colour saturation) to PC
XGA 60Hz INPUT 4.
100% Checkered Pattern *Please make sure SYNC is OFF.
[Terminal]
PC INPUT 4
2 Auto adjustment Process Mode page 6 1) At the related page, move cursor to [RGB ADJ], press ENTER.
performance (PC-RGB) 2) [OK] appears when finished.
4–4
5.2. White balance adjustment

1 Adjustment Brightness : MAX For the details of white balance adjustment procedure, please refer to white balance
AV Mode: DYNAMIC adjustment spec for Kameyama model.
Active Backlight : OFF
Set the luminance meter on 1) Confirm the set condition.
the center of the screen
2) Connect the white balance jig.
3) Through RS-232C command, adjustment mode screen is displayed.
2 Auto Adjustment [command] [Adjustment Procedure]

performance Adjustment Mode 1) Using the remote control, set the LCD TV to adjustment mode.
KRSW0001
KKT10037 2) Measure Max brightness (Lmax).
FACT0001 3) Calculate min. brightness (Lmin)=Lmax/1000.

Setting
KYOF0001 4) Measure Point 2 brightness (Lhigh).
OSDS0001
SBSL16_ _ 5) Set the reference value R,G,B of Point 2 (R2)=3664 x (229/P2)
where P2=255 x [(Lhigh-Lmin)/(Lmax-Lmin)]1/2.2
Multi point adj. Mode
MSET0000 6) Set the specified gradation for point 2, fix the most faint colour to get reference
WBI20255 value, adjust others 2 colour to minus adjustment for reference value of point 2.
Point 2 7) Measure Point 1 brightness (Llow).

WBI20229
MG2G**** 8) Set the reference value R,G,B of Point 1 (Ref.1)=608 x (38/P1)
MG2B**** where P1=255 x [(Llow-Lmin)/(Lmax-Lmin)]1/2.2
MG2R****
9) Set the specified gradation for point 1. Set G of point 1 to the default value [(Ref.1 x
Point 1 G value of point 2/Ref.2), with fractions rounded] and adjust RB to the reference
WBI10038 value of point 1.
MG1G****
MG1B**** 10)Set the G of point Max. to the default value (4080 x G value of point 2/Ref.2). Set
MG1R**** the R,B Max. value [Gmax-G value of point 2 + (R,B value of pint 2)].
Write 11)Adjusted value is writing at [command] MSET0003.

MSET0003
12)Shut down the AC power.
Set Max.Level
MGMG**** *Initial value at RGB 2 point : 3664
MGMB**** *Initial value at RGB 1 point : 608
MGMR****
[Adjustment Value]
✩Teaching set send by engineering dept is set as reference.
[Reference value for adjustment reference]

Equipment: Luminance meter [Minolta CA-210]
Spec Adjustment Inspection

Level
Data Spec. Spec.
Point 2 x=0.281
ref. 229 r0.0010 r0.0020
y=0.288
values
Point 1
x=0.272
ref. 38 r0.0045 r0.0090
y=0.277
values
Ref. : For inspection, set the LCD TV as below.
AV MODE: [DYNAMIC] (Reset)
Aging Time: Minimum 30 minutes
4–5
6. Factory setting
AC power is plug off after shipment setting is done.
CAUTION: Do not plug on again after shipment setting is done. If do, please re-do the shipment setting. Do not off with remote control.
Adjustment item Adjustment condition Adjustment procedure

Factory setting AC power off to exit the fac- 1) Setting is done with test remote control.
tory setting. 2) Press the “Factory Setting” key on the remote control continuously.
3) When Green background appears on screen and “K” mark disappears, setting is com-
pleted.
The followings are initialized to factory setting
1) User setting
2) Channel data (e. g. broadcast frequencies)
3) Manufacturer’s option settings
4) Password data
5) Setting values are set based on model destination
Model Name Factory Setting Key Remote Control S-System OSD Language
Name Code Setting Setting
LC-32LE240M/340M
(For Asia, Indonesia,, Vietnam, Thailand, Middle M-Setting 100000001010110 B/G ENGLISH
East)
LC-32LE240M/340M (For Philippines) P-Setting 100000001011110 M ENGLISH
**Please do inspection for LC-32LE240M/340M (for Philippines) using NTSC signal.
4–6
[2] USB Clone (Smart Loader)
1. Description
The Smart Loader is a function implemented in the service software to easily replicate the user settings of one TV into another.
These settings include (but not restricted to): picture and audio, turning set-up, language and country selection, PIN, child locked programs etc.
Factory adjustments are not copied as they are different for every TV.
The Smart Loader makes possible the user data to be stored in a memory device connected to the USB terminal of the TV that is used as reference
and later load those data into other TVs by using their respective USB terminal.
2. How it works
1. Enter USB clone menu (Smart Loader)

i) Press panel key [TV/VIDEO] and [VOL+] and AC on, it will go to password entry OSD
---
ii) Enter digit “369” then it will go to Smart Loader Menu

Smart Loader
SMLD Store [ ]
SMLD Restore [ ]
2. Smart Loader function
SMLD Store SMLD Restore
1st AQUOS TV USB 2nd AQUOS TV
i) SMLD Store
• To copy all related data from TV -> USB and put under a fixed filename “SHP_SMLD.bin” (8kB).
ii) SMLD Restore

• To restore the related data from USB -> TV.
iii) SMLD Store and Restore execution

• To execute SMLD Store or SMLD Restore, highlight at selected item and press Enter.
• When copying is in process, “WAIT” is displayed.
• After cloning process is done, “OK” is displayed.
If cloning process is not finished due to error (e.g. no pendrive detected), “NG” is displayed.
3. Exit USB Clone menu (Smart Loader)

i) To exit Smart Loader menu, plug off AC Cord.
4–7
[3] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following two ways to get the public mode setup screen displayed.
1) Press the “INPUT” and “VOL (+)” keys on the set at once and turn on the power.
2) Get the password input screen displayed.
Procedure
• The input starts with the leftmost digit.
• Use the numeric keys [1] thru [9] and [10/0] keys on the remote controller.
The other keys are not acceptable.
• With a numeric-key input, “–” will change to “ “. The input position will move one digit to the right.
• With all the 3 digits entered, the password will be verified.
3) The 3-digit password is now verified.

The password [0] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.)
With any other passwords, the screen changes to the normal mode.
In the adjustment process mode, turn on “PUBLIC MODE”. Also press the “CH ( )” and “VOL (+)” keys on the set at once and turn on the power.
2. How to exit Public Mode

There are the following ways to quit the public mode setup screen.
• Turn off “PUBLIC MODE” in the adjustment process mode. ( ) ← This way alone is not for quitting the setup screen, but for quitting the mode by
itself.
• Turn off the power with the “POWER” key. ( )
• Select “EXECUTE”.( )
••• “PUBLIC MODE” stays on in the adjustment process mode.
••• The settings will be back to the factory ones.
3. Public Mode Setting Values

• With the factory settings made, the public mode settings get initialized. (The adjustment process remains intact.)
4–8
4. Public Mode Menu
The guidance is not displayed onscreen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “Execute” and use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote con-
troller and set).
PUBLIC MODE
POWER ON FIXED [ VARIABLE ]

MAXIMUM VOLUME [ 60 ]
VOLUME FIXED [ VARIABLE ]
VOLUME FIXED LEVEL [ 20 ]
RC BUTTON [ RESPOND ]
PANEL BUTTON [ RESPOND ]
MENU BUTTON [ RESPOND ]
ON SCREEN DISPLAY [ YES ]
BLUE SCREEN [ NO ]
INPUT MODE START [ NORMAL ]
INPUT MODE FIXED [ VARIABLE ]
232C POWON [ DISABLE ]
START UP SCREEN [ OFF ]
PICTURE IMPORT [ OFF ]
RC PATH THROGH [ OFF ]
RESET
EXECUTE
<Example of image>
5. On Setting Items
1. POWER ON FIXED
Selection Variable/Fixed
Default Variable
Explanation When set to “Fixed”, the power cannot be turned off with the power key on the remote control or main unit, and the image
reception state is kept (it does not enter the standby state).
The power can be turned off by shutting off power supply from AC.
Limit in setting • Power key on the main unit/remote control power supply key
• OFF timer/ON timer
Exception None
Remarks • Selection of “FIXED” assumes use of STB, etc.
• When set to “Variable”, if the main power switch is set to off, the power is turned off after a wait of 1 second.
(Push-push switch only)
• Display ON/OFF in the hotel menu is controlled by the adjustment process “HOTEL POWERFIX”.
• When the power button is operated, a caution is displayed (it times out in 5 seconds).
(For the caution, refer to the power on fixed message sheet.)
* The caution is not displayed when in the adjustment process, hotel menu, default setting, MCL operation and auto preset
(Ch search operation).
The OSD display including the menu and this caution have priority over all others.
When “OSD display” (described below) is set to “Variable”, this caution is displayed as a special case.
2. MAXIMUM VOLUME
Selection Adjustment from 1 to 60 (no loop)

Default 60
Explanation Sound volume can not be adjusted higher than the preset value.
Limit in setting • When the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed.
• The maximum sound volume for ON-timer (Wake up timer) is limited also to the preset value.
Exception • In the item “VOLUME” of adjustment process, the sound volume can be set freely irrespective of this setting.
Remarks • Setting is valid only for the speakers of the unit. (As for the headphone, the sound volume can be set up to 60 irrespective
of the limit.)
• In line output (sound volume variable), the sound volume can be adjusted from -60 to 0 irrespective of pre-adjusted value.
• When the sound volume is set higher than the MAX setting by the adjusting process or headphone, the sound volume con-
trol operation is prohibited for turn-up and the sound volume should be turned down to MAX in this state.
4–9
3. VOLUME FIXED
Selection Selection between “Variable” and “Fixed” (loop provided)

Default Variable
Explanation Sound volume is fixed and made invariable.
Limit in setting • The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made
impossible. (Basically, the menu is not displayed.)
• The following keys become invalid:
1) Sound volume Up/Down (VOL +/-) [for both remote control and the unit]
2) Mute (MUTE)
Exception • In the item “VOLUME” of adjustment process, the sound volume can be set freely irrespective of this setting.
Remarks • In “Variable” setting, the sound volume had been conventionally set at 1 but this operation has been abolished (and follows
the last memory).
• The sound volume for the ON-time is not set at 1 either and the sound volume set value of the ON-timer before the hotel
mode is executed.
• Setting is valid only for the speakers of the unit. (As for the headphone, the sound volume can be set up to 60 irrespective
of the limit.)
• In line output (sound volume variable), the sound volume can be adjusted from -60 to 0 irrespective of pre-adjusted value.
• As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority.
• Once the sound volume has been changed by adjustment process or headphone, it should be set back to the sound volume
preset by sound volume fixing level when the adjustment process ends or when the headphone is removed.
4. VOLUME FIXED LEVEL
Selection Adjustment from 1 to 60 (no loop)

Default 20
Explanation The sound volume to be fixed by “Volume fixed” is determined.
Limit in setting None
Exception None
Remarks Setting is valid only when “Volume fixed” is selected for “fixed”.
This must be confirmed actually by changing also the sound volume in accordance with setting.
5. R/C BUTTON
Selection Selection between “Respond”, “Limited” and “No respond” (loop provide)
Default Respond
Explanation Acceptability of keys by remote control is limited or reception of keys can be prohibited.
Limit in setting 1) In “limited” setting, only power ON/OFF, sound volume , tuning and BACKLIGHT (brightness sensor) are
accepted.
2) In “No respond” setting, all the keys (including the power key) are not accepted.
Exception • Adjustment process, factory setting, inspection process and hotel only keys are valid irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
6. PANEL BUTTON
Selection Selection between “Respond” and “No respond” (loop provide)

Default Respond
Explanation All the operations by keys (except the power key) of the unit can be invalidated.
Limit in setting
Exception • Inspection mode and hotel menu mode can be started irrespective of setting.
Remarks
7. MENU BUTTON
Selection Selection between “Respond” and “No respond” (loop provide)

Default Respond
Explanation In “No respond” setting, the menu operation by the menu key of the remote control and the menu key of the unit is invalidated.
Limit in setting • ON-timer (Wakeup Timer) is turned OFF.
• The following keys become invalid.
Wake-up timer and clock setting keys and all of the direct change keys to menu display
Exception • Inspection mode and hotel menu mode can be started irrespective of setting.
Remarks
4 – 10
8. ON SCREEN DISPLAY
Selection Selection between “Yes”, “No” (loop provide)

Default Yes
Explanation The following OSD displays are made ineffective.
Displays of menu group, channel call, sound volume bar and direct key call
Limit in setting • Set time of the OFF-timer (SLEEP TIMER) is cleared.
• Setting of the no-signal power-OFF (AUTO POWER OFF) is cleared to “OFF”.
• Setting of the no-operation power-OFF is cleared to “OFF”.
• Keys falling under any of the following items become invalid.
1) Appearance of screen changes and the sound changes.
2) Personal functions which are hard to restore.
Ex.) Screen display, menu, OFF-timer, ON-timer, AV MODE, screen size switching, clock setting, treble emphasis,
AUDIO ONLY, sound changeover, LANGUAGE, CLOSED CAPTION
Others • Simple input switching is generated. Those which are restored soon after leaving as they are and may be requested for
change by customer are not prohibited.
Ex.) Brightness sensor (BACKLIGHT) and PIC. FLIP
Exception • Such a caution which is displayed independently is displayed as it is.
Non-responding signal caution, TELE TEXT caution and power-ON fixing caution
9. BLUE SCREEN
Selection Selection between “Yes”, “No”

Default No
Explanation When no signal inputs, selecting the background color.
Selected to “Yes”---Blue screen
Selected to “No”---No Blue screen
10.INPUT MODE START
Selection Selection between “Normal”, “TV (CH~)” “INPUT1~8” (loop provide)

Default Normal
Explanation In power-ON, the input source to be started or channel can be set.
(In standard mode, the operation follows the last memory.)
About options • All the input sources in the model are made selectable.
• When the input/output switchable input source is selected and the input source is set to output, the setting of input/output
switching is changed to input at the execution of hotel menu. In addition, the input/output switching by menu is prohibited.
• In TV mode, the display of all channels is stopped and it is treated as an input source. At this time, the channel to be set fol-
lows the last memory and the content of the last memory is included in the notation by options. Ex.) TV (CH2), TV (CH4)
etc.
• The order of appearance of options in the hotel menu should agree with the order of toggles by input switching key.
Limit in setting • The display of channel setting menu and the channel setting operation are prohibited (except for MCL).
Exception None
Remarks • In setting at “Normal”, the setting of “Input mode fixed” is changed to “Variable” and selection should be prohibited.
11.INPUT MODE FIXED
Selection Selection between “Variable” and “Fixed” (loop provide)

Default – (Variable)
Explanation The input mode is fixed at the input source or the channel set at the “Input mode start” in 9 and other input sources and chan-
nels can be made non-selectable.
Limit in setting • With the execution of hotel mode, the input source is forced to change to that set by “Input mode start” and the channel
switching and input switching are prohibited thereafter.
• The following keys are invalidated.
CH , direct tuning button, FLASHBACK, input
*However, the keys (input switching and CH , keys) of the unit for menu operation remain valid.
Exception None
Remarks • In the following case, setting is cancelled and mode is changed to “Variable”.
When the setting of “Input mode start” is set to “Standard (Normal)”
12.232C POWON
Selection “Enable” and “Disable”

Default Disable
Explanation When in the standby state, power ON by the RS-232C command is enabled or disabled.
Limit in setting None
Exception None
Remarks RS-232C power ON command “POWR1_ _ _ ”
4 – 11
13.RC PATH THROUGH
Selection “Off”, “On: TV RCE”, “On: TV RCD”

Default Off
Explanation Remote control signal output from the pin 9 of the RS-232C terminal and signal reception is enabled or disabled.
When set to “ON: TV RCE”, TV also receives signals. With “ON: TV RCD”, the remote control signal is output from the pin 9,
but TV does not respond to the remote control.
Limit in setting When set to “ON: TV RCD”, TV does not accept the remote control.
Exception None
Remarks
4 – 12
LC32LE240M
Service
CHAPTER 5. TROUBLESHOOTING TABLE Manual
[1] TROUBLESHOOTING TABLE

No power (front LED failure to light up) or no startup (front LED failure to turn from red to green)
Are the wire harnesses and other cables properly connected in NO Reconnect the wire harnesses and other cables properly in the
the set? set.
YES
Is there the AC_CTRL and PNL_POWER signal input at pins NO Check the AC_CTRL signal line PNL_POWER signal line.
(126) and (127) of IC3301?
YES
Are the DC/DC converter outputs and the output voltages along NO Check the DC/DC converters and the control lines. Replace
the control lines as specified? defective parts as required.
1) M+5.6V (IC9603)
2) D+1.26V (IC9605)
3) D+5V (IC9610)
4) T+5V (IC9612)
5) D+3.3V (IC9608)
6) D+1.8V (IC9609)
7) D+2.5V (IC9611)
5–1
With [RF] signal input No video onscreen (1)
No video in the UHF/VHF reception
Is there IF output from the tuner pin(10) of TU1101 as specified? NO Check TU1101 and its peripheral circuits.
YES
Is there VIF input at pin 74 & 75 of IC3301? NO Check the circuit between TU1101 & IC3301.
YES
Are there the signal outputs (pin 100-107, 109,110) of IC3301? NO Check IC3301 and its peripheral circuit.
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
With <Video> signal input No video onscreen (2)
No external input video onscreen <INPUT 2>
Is INPUT 2 selected on the input select menu screen? NO Select INPUT 2 on the input select menu screen to pick up the
right input signal.
YES
Is there the video signal input at pin (43) of IC3301? NO Check the line between pin (9) of J502 and pin (43) of IC3301.
YES
Are there the signal outputs (pin 100-107, 109,110) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
eral circuits.
5–2
With <Component> signal input No video onscreen (3)
No external input video onscreen <INPUT 3>
Is INPUT 3 selected on the input select menu screen? NO Select INPUT 3 on the input select menu screen to pick up the
right input signal.
YES
Are there the Y, Pb and Pr signal inputs at pins (34), (36) and NO Check the line between pins (19)/(17)/(15) of J502 and pins (34)/
(38) of IC3301 respectively? (36)/(38) of IC3301.
YES
YES
eral circuits.
With <HDMI> signal input No video onscreen (4)
No external input video onscreen <INPUT 1>.
Is INPUT 1 selected on the menu screen? NO Select INPUT 1 on the input select menu screen to pick up the
right signal input.
YES
Are there signal outputs from SC1501 to IC3301? NO Check peripheral circuits between SC1501 and IC3301.
YES
YES
eral circuits.
5–3
No audio heard (1)
No sound in the UHF/VHF reception.
Is the IF output from the tuner pin (10) of TU1101 as specified? NO Check TU1101 and its peripheral circuits.
YES
Is there the SIF signal input at pins (77), (78) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Is there audio signal intput at pin(6) of IC1701? NO Check connection between IC3301 and IC1701 and its
peripheral circuits.
YES
Is the L-ch audio signal output at pin((28), (30) of IC1701 normal? NO Check IC1701 and its peripheral circuits.
Is the R-ch audio signal output at pin(12), (14) of IC1701 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC1701 & P1701.
P1701 normal?
YES
Check speakers and their peripheral circuits.
5–4
No audio heard (2)
No external audio heard

<INPUT 2>
Is there the L-ch audio signal input from pin (7) of input terminal
J502 to pin (47) of IC3301?
Is there the R-ch audio signal input from pin (5) of input terminal
J502 to pin (48) of IC3301?
<INPUT 3>
Is there the L-ch audio signal input from pin (13) of input terminal
J502 to pin (49) of IC3301?
Is there the R-ch audio signal input from pin (11) of input terminal
J502 to pin (50) of IC3301?
YES
Is there the I2S signal output at pin (80), (81) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Is there audio signal input at pin(6) of IC1701? NO Check connection between IC3301 and IC1701 and its periph-
eral circuits.
YES
Is the L-ch audio signal output at pin(28), (30) of IC1701 normal? NO Check IC1701 and its peripheral circuits.
YES
P1701 normal?
YES
5–5
No audio heard (3)
No HDMI sound heard. <INPUT 1>

(*INPUT 1 is digital audio.)
Does the HDMI image appear onscreen? NO Refer to “<INPUT 1> in No external input video onscreen
(HDMI)”.
YES
No audio output from <INPUT 1> NO Check it if EDID is written or not.
YES
Are waveforms input in to the pin(3)-(6), (8), (9), (11), (12) NO Check peripheral circuits IC3301.
of IC3301 normally?
YES
eral circuits.
YES
YES
P1701 normal?
YES
5–6
No audio heard (4)
No sound from the HDMI sound input terminal.

(INPUT 1 analog audio)
YES
Is there the L-ch audio signal input from pin (2) of external input
terminal J506 (HDMI AUDIO IN) to pin (55) of IC3301?
Is there the R-ch audio signal input from pin (3) of external input
terminal J506 (HDMI AUDIO IN) to pin (56) of IC3301?
YES
Are I2S signal output from the pins (80), (81) of IC3301 normally? NO Check peripheral circuits of IC3301.
YES
eral circuits.
YES
YES
P1701 normal?
YES
5–7
No audio heard (5)
No PC audio output
YES
Pin (2) of J506: Is L-ch input into the pin (55) of IC3301?
Pin (3) of J506: Is R-ch input into the pin (56) of IC3301?
YES
Are I2S signal output from the pins (80), (81) of IC3301 normally? NO Check peripheral circuits of IC3301.
YES
Is there audio signal input at pin(6) of IC1701? NO Check connection between IC3301 and IC1701 and its
peripheral circuits.
YES
YES
P1701 normal?
YES
5–8
5–9
LC32LE240M
CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM Service Manual
[1] OVERALL WIRING DIAGRAM
I
Hiraki-Panel
R1LK315T3HB00W 1 32
MAIN
F 32LE340M --> DUNTKF998FMG4
32LE240M --> DUNTKF998FMG5
QCNW-M466WJQZ
[LW]
Power Unit 32 - 1
E RUNTKA929WJQZ USB
HP
[SP] PC audio in
[PD] 1
10 QCNW-M465WJQZ HDMI
4
1 Tuner
D D-Sub
NL
1-4 [PD]
[AC] 1
[L1] QCNW-M467WJQZ
QCNW-M468WJQZ 10
12 12
C
SP - R SP - L
SP-R SP-L
RSP-ZA571WJZZ RSP-ZA570WJZZ
LED PWB A
LED PWB B
RUNTKA927WJZZ
RUNTKA928WJZZ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
6–1

[2] SYSTEM BLOCK DIAGRAM
MAIN UNIT
HDMI1 TUNER
TUNER
HDMI1 TU1101
HDMII SC1501 RTUNQA067WJQZ
QSOCZA271WJQZ
IF
Y IF AMP I2C
H EDID
HPD0 IN D5V
IC1501
VIF SAW KEY/RC/LED
SIF AMP
data
Filter
I2C
clk
Filter
KEY/SW IR Receiver LED
IF_SW
RC
TEMP SENSOR KEY1/2 LED_G,R

VIF+ SIF+
VIF- SIF- TH3301 PSW_IN
Terminal
POWER UNIT
IR IN
SAR(2)
GPIO37
HDMI1 CEC
VIF IN
GPIO6
SAR(0)
SAR(1)
GPIO10
SIF IN
G HDMI
EEPROM IC508
SDA SCL
VHIBR24T02J
PC RGB
PC D-sub 15pin PC DDC
HD
SC502
VD
PC Audio J506 L/R
Y/Pb/Pr
CVBS/COMP IN J502 CVBS
CVBS & Audio L/R
COMP
COMP Audio IN J502 AUDIO
PD PD
L/R
F UR+12.2V UR+12.2V
LED UNIT
USB IN J501(side) USB IF
DP/DN GND GND
L1
ERROR PS_ON PS_ON L1
LED1_A
Mon L/R OUT J502 Mon Amp circuit Monitor Audio ERROR ERROR LED1_A
OFL LED1_K
OFL OFL LED2_A LED1_K
INV_POW 2pin
STB STB LED2_K
4pin
HP Amp circuit
HP J504(side) HPAudio out
HP Det PANEL_12V
LED UNIT
Data A 8
MST6100VS RH-IXD454WJQZQ (340M) Panel Hiraki
LVDS 8bit
E MST6003VS RH-IXD459WJQZQ (240M) Clk A 2
P2601
Data A 8 32" WXGA
30 pin L1
MSTAR TCON_WP
LED1_A
Clk A 2 LED1_K
I2C IC3801 I2C
2pin
I2C SW
XIN/XOUT
Xtal (24.0MHz)
X3301
I2C Address A8
I2C EEPROM(HDCP)
IC3103
RH-IXD110WJQZY
D
I2C I2C Address A4
EEPROM(DRAM)
IC3102
VHIBR24T28F-1Y
C DRAM IF AUDIO OUT SPI IF

I2S
H/W RESET
SP MUTE
SPI_WP
SPI
RESET DDR2 (128Mb) SPI FLASH

AUDIO AMP
IC3302 IC3501 IC3101
IC1701
RH-IXD361WJQZQ RH-IXD464WJQZQ
VHIYDA164DZ-1Y
(LE340M)
RH-IXD463WJQZQ
SP_L
SP_R
(LE240M)
B
SP P1701
QPLGNA961WJZZY
4 LCH(+)
3 LCH(-)
2 RCH(-)
1 RCH(+)
SP_L
SP_R
SP_L SP_R
A
8 5W 8 5W
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
6–2

LC32LE240M
CHAPTER 7. PRINTED WIRING BOARD ASSEMBLIES Service Manual
[1] MAIN Unit
MAIN Unit
(Side-A)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
7–1

MAIN Unit
H (Side-A Chip)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
7–2

MAIN Unit
(Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
7–3

MAIN Unit
H (Side-B Chip)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
7–4

LC32LE240M
CHAPTER 8. SCHEMATIC DIAGRAM Service Manual
[1] DESCRIPTION OF SCHEMATIC DIAGRAM

1. VOLTAGE MEASUREMENT CONDITION:
1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 110-240V. Signals are fed by a colour bar signal
generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester.
2. INDICATION OF RESISTOR & CAPACITOR:

RESISTOR
1) The unit of resistance "Ω" is omitted.
(K=kΩ=1000Ω, M=MΩ).
2) All resistors are ± 5%, unless otherwise noted.
(K= ± 10%, F= ± 1%, D= ± 0.5%)
3) All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1) All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2) All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH " "( ) ARE IMPORTANT
FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO
REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAIN-
TAINING THE SAFETY AND PERFORMANCE OF THE SET.
8–1

[2] MAIN Unit
• MAIN Unit-1/11
MAIN1 (TUNER)
I
TU1101
QA067WJQZ
GND GND
NC NC NC RF AGC +5V SDA SCL NC NC AIF NC

GND GND
1 2 3 4 5 6 7 8 9 10 11
H
R1132 R1133 TO MAIN10(POWER)

4.7K 4.7K
D+3.3V
T+5V
C1118 FB1102
C1121
R1143 0.01u A191WJ
10u
100 L1103 16V
R1115 0.82uH R1118 KZA837WJQZ
1.5K SBN 680
G R1144 CZ
100
C1123
47P R1116
C1103 C1105 C1106 C1107 C1122
0.1u 10u 10u 10u 47P 270
10V 16V R1105
16V 16V
100 C1114
R1113 0.01u
56
C1110 R1111
C1108 12K R1119
0.01u C1113 Q1101
0.01u 0
0.01u
DSC2G03
R1138 R1114
22K R1117
820 C1115
68
F 0.01u
FB1101
A191WJ
FL1101
CA072WJQZ
1 4
C1116
E 0.01u
R1125 3
0
R1131
22K
C1120
0.01u
TO MAIN5(CPU)
R1102 SIFP
6.8K
SIFM
1 4 VIFP
C1117
0.01u
FL1102
D1101
R1103 2 CA058WJ
C 6.8K VHD
KDS114E
R1127
3.3K
5 VIFM
VS
IF_SW
B Q1105
LTC044EEB
I2C_CLK
I2C_DAT
TAGC
A DUNTKF998WE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–2

• MAIN Unit-2/11
MAIN2 (HDMI-TERM)
I
G
TO MAIN10(POWER)
D+5V
D+5V
BU+3.3V
BU+3.3V
R1510
10K
TOP Q1503 CZ
F INPUT1 SC1501
ZA271WJQZ
D1510 D1516
DB2S310L DB2S310L LTC044EEB
24 25 Q1501
20
2 4 6 8
21 R1511 LTC044EEB Q1502
10 12 14 16 18 47K CZ
LTC044EEB TO MAIN5(CPU)
1 3 5 7 9 11 13 15 17 19
22 23
R1505 HPD_+5V_IN
1K
1 3
HPD_CTRL
R1516 WP_CTRL
E 47K
2
HDMI_DAT
HDMI_CLK
1 3
HDMI0_CLKN
HDMI0_CLKP
R1504
10 HDMI0_CLKN
R1503
HDMI0_D0N
2
47K
CZ HDMI0_CLKP
HDMI0_D0P
D HDMI0_D1N
HDMI0_D0N
HDMI0_D0P
HDMI0_D1P
8 7 6 5 HDMI0_D1N
HDMI0_D2N C1501
10u VCC VCLK SCL SDA
HDMI0_D1P
16V
HDMI0_D2P
KZA837WJQZ IC1501
HDMI0_D2N
BR24T02J
C1502 EEPROM HDMI0_D2P
0.01u A1 A2 GND
A0
25V
CZB
1 2 3 4
R1547
200
HDMI_CEC
HDMI_ARC
DUNTKF998WE
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–3

• MAIN Unit-3/11

1PVJKUOQFGNVJG/CKP%KTEWKV$CUKE&KCITCOKUPQVCRRNKGF
MAIN3(TERMINAL)
I J502 LA047WJQZ
AV1_V AV1_L AV1_R AV_OUT_L AV_OUT_R
HP SIDE
J504
J0101SE
COMP_CR COMP_CB COMP_Y COMP_L COMP_R
10 9 20 19 8 7 18 17 6 5 16 15 4 3 14 13 2 1 12 11 7 6 2 3 4 5 1
H C501
0.01u
R506 R510
R503
100K 100K
1K
R519
R512
R501
0
0
R520
R521
R518
R514
R523
R522
C502 C504
R517
C527
0
0
0
0
1000P 10P 10P
C526
1000P TO MAIN5(CPU)
C530 C532 C517 C514
56P 56P 56P 56P
G R528 R526
COMP1_Y
R548 100 100 COMP1_Pb

R533 R549 75 1/4W
75 75 R534 R536 R547 R516 1/4W R513
TQ
TQ TQ 10K 10K 75 10K 10K COMP1_Pr
TQ
C509 CVBS1
(PWB) 0.01u (PWB) C508 (PWB)
(PWB)
C531 C533 C518 0.01u C515
1000P 1000P 1000P 1000P
R527
R525
100K
USB:500mA max 100K
J501
COMP_AUD_L
ZA284WJQZ R532 R535 R509 R515 R511
12K R507 12K
USB Atype Right Angle 12K 12K 1/4W
100 COMP_AUD_R
100
TW 1/4W
FB503 L501 TW
R502 R505 R508 CVBS_AUD_L
A206WJ FA154WJ
33 33
GND 10K
4
CVBS_AUD_R
USB_D0P
COMP_AUD_R
USB_DP 4
COMP_AUD_L
3
2
CVBS_AUD_R
CVBS_AUD_L
MON_R_OUT
MON_L_OUT
COMP1_Pb
HP_R_OUT
HP_L_OUT
COMP1_Pr
F
COMP1_Y
USB_D0N
HP_PLUG
USB_DN 3
2
1
CVBS1
VA505 VA506
+5V
1
VXA074WJ VXA074WJ
FB507
A206WJ 39V 39V
1.1pF 1.1pF
WP_CTRL
5 4
R631
Vout Vin 10
C503 C581 UART_DEBUG_RX
10u 10u R632
16V IC510 16V 10
UART_DEBUG_TX
PC_R
KZA837WJQZ S172B50U KZA837WJQZ PC_G
ON GND N.C.
PC_B
1 2 3
PC_R PC_HSYNC_IN
E FB521
0093GE
R582
D510
BAV70
PC_VSYNC_IN
75
TQ PC_AUD_L
SC502 1
R601 PC_AUD_R
1K NB037WJQZ 3
PC_G 2
R608 R607 R625
47K 47K J
5
FB522 47K
R616 UART_232C_TX
0093GE
R583 100
75
17
10
16
9
TQ UART_232C_RX
15
14
13
12
11
UART_DEBUG_RX
R615
PC_B 100 UART_DEBUG_TX
FB523 R626
0 CZ USB_D0P
0093GE R584 8 7 6 5
75
TQ USB_D0N
C565 VCC VCLK SCL SDA
10u
16V IC508 HP_PLUG
D FB517
KZA837WJQZ
C566 BR24T02J
A369WJ
0.01u EEPROM
R524 R577 25V A1 A2 GND
FB518 A0
0 10K J
2 PC_AUD_L A369WJ
1 2 3 4
3
1 C544 C553
R590
56P 1000P
J506 CH 12K
CH TO MAIN9(AUDIO_AMP)
JA024WJ WP_CTRL HP_R_OUT
FB519 R620
PC AUDIO A369WJ 100
HP_L_OUT
R529 R578
0 10K J R613 MON_R_OUT
PC_AUD_R R614
FB520 100 R621
A369WJ 100 100 MON_L_OUT
C543 R581 C548
56P 1000P
12K C560
CH CH R610 R611 C561
2.2K 47P 47P
2.2K
CH
C CH
PC_HSYNC_IN
PC_VSYNC_IN
TO MAIN10(POWER)
D+5V
M+5.6V
BU+3.3V
B
TL504
TL505 UART_232C_TX
TL506 UART_232C_RX
TL507
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–4

• MAIN Unit-5/11 (LC-32LE240M)
MAIN5 (CPU)
TO MAIN10(POWER)
R3337
CPU BU3.3V : 5.6mA(Max) 33K
BU+3.3V
4
D+2.5V
R3321
2.7K
D+3.3V
3
D+1.8V
CPU BU1.26V : 23.9mA(Max)

D+1.26V
D+5V
PANEL_POW TO MAIN11(KEY)
H AC_CTRL
TO MAIN6(DDR)
RC
R3339 100
R/C
POW_CHK LED_G
FB3308
INV_POW
AC_CTRL
S_RESET
PWM0_OFL
LAMP_ERR
A_DDR_D9
A_DDR_D6
A_DDR_D1
A_DDR_D3
A_DDR_D4
IR_PASS
A_DDR_A1
A_DDR_A3
A_DDR_A5
A_DDR_A7
A_DDR_A9
A_DDR_DQM0
A_DDR_DQM1
A_DDR_D14
A_DDR_D12
A_DDR_D11
A_DDR_A10
A_DDR_A12
A192WJ
A_DDR_DQS0N
A_DDR_DQS0P
A_DDR_CLKEN
A_DDR_WE#_HSS
DDR_VREF FB3313 LED_R

A_DDR_BA1_HSS
A_DDR_BA0_HSS
A_DDR_BA2_HSS
DDR_VREF FB3302 FB3303 FB3304

A192WJ
A192WJ A192WJ A192WJ
A_DDR_DQM0 FB3307
R3353
A_DDR_DQM0
R3336
A192WJ
10K
R3377
10K
R3385 C3341
TO MAIN1(TUNER) A_DDR_DQM1 0
A_DDR_DQM1 0 10u
C3302 16V
C3304 C3306
VIFP A_DDR_DQS0N 10u KZA837WJQZ R3338
A_DDR_DQS0N 16V 0.1u 0.1u
1K
KZA837WJQZ
%35739
VIFM A_DDR_DQS0P
A_DDR_DQS0P KEY1
4 3 KEY_1
TP3308
SIFP A_DDR_DQS1N
A_DDR_DQS1N C3318 KEY2
2 1 KEY_2
10u
SIFM A_DDR_DQS1P 16V
RXE_D0N
RXE_D0P
A_DDR_DQS1P
KZA837WJQZ TP3305
PSW_IN
A_DDR_D0 PSWIN
I2C_CLK A_DDR_D0
R3345
A_DDR_D1 C3336 1K
I2C_DAT A_DDR_D1 0.1u TO MAIN8(PANEL) C3349
0.1u
A_DDR_D2 10V
IF_SW A_DDR_D2 RXE_D0P
R3302 A_DDR_D3 C3351 C3352 C3353

A_DDR_D3 RXE_D0N
5.6K 100P 100P 100P
0.1u
C3335 CCZ
T_AGC A_DDR_D4 C3320 C3321 C3322 C3324 C3326 C3327 C3331 C3333 CCZ CCZ
G
TAGC A_DDR_D4 0.1u RXE_D1P
R3349 0.1u 2.2u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u
C3337
0 A_DDR_D5
A_DDR_D5 RXE_D1N
C3361 C3362
A_DDR_D6
0.022u 0.1u A_DDR_D6 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 RXE_D2P
C3340
A_DDR_D7
A_DDR_D7 0.1u
PWM1
PWM0
VDDC
VDDC
WEZ
VDDP
DQSL
RXE_D2N
DQMU
DQML
MCLKE
DQSLZ
LVB0M
LVB1M
LVB2M
LVB3M
LVB4M
LVB0P
LVB1P
LVB2P
LVB3P
LVB4P
LVA0M
LVBCKM
LVA0P
R3430
AVDD_MOD
LVBCKP
DVDD_DDR
GPIO77
GPIO76
GPIO75
GPIO74
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
MADR[1]
MADR[3]
MADR[5]
MADR[7]
MADR[9]
MADR[12]
A_DDR_D8
AVDD_LPLL
C3311
BADR[1]
BADR[0]
BADR[2]
10K
MDATA[9]
MDATA[6]
MDATA[1]
MDATA[3]
MDATA[4]
MADR[10]
A_DDR_D8
MDATA[14]
MDATA[12]
MDATA[11]
0.1u RXE_CLKP TO MAIN7(FLASH)

AVDD_ AVDD_MOD
USB_PLUG A_DDR_D9 163 MEMPLL 108 SPI_CS0N D3301 SPI_CZ
TP3307
A_DDR_D9 RXE_CLKN SPI_CZ

R3363 DA1010
A_DDR_DQS1P LVA1M RXE_D1N
R3316 C3350 A_DDR_D10 164 DQSU 107 SPI_SCLK 100 SPI_CLK
33 0.047u RCA_CVBS2_IN A_DDR_D10 RXE_D3P SPI_CLK
A_DDR_DQS1N RXE_D1P R3365
TO MAIN3(TERMINAL) A_DDR_D11 165 QDSUZ LVA1P 106 SPI_SDI_DAT 100 SPI_DI_DAT
A_DDR_D11 RXE_D3N SPI_DI_DAT
A_DDR_D15 RXE_D2N R3366
CVBS input A_DDR_D12 166 MDATA[15] LVA2M 105 SPI_SDO_DAT 100 SPI_DO_DAT
A_DDR_D12 SPI_DO_DAT
R3304 C3308 A_DDR_D8 RXE_D2P I2C_DAT
RCA_CVBS1_IN 167 LVA2P 104
33 0.047u A_DDR_D13 MDATA[8]
CVBS1 A_DDR_D13 I2C_CLK
LVACKM RXE_CLKN
A_DDR_D14 168 AVDD_DDR 103 I2C_CLK
C3366 A_DDR_D14 C3312 I2C_DAT
R3357 68 0.047u VCOM0 A_DDR_D10 0.1u RXE_CLKP
169 LVACKP 102
A_DDR_D15 MDATA[10]
A_DDR_D15 SPI_WP
Component input A_DDR_D13 RXE_D3N
170 LVA3M 101
A_DDR_BA0_HSS MDATA[13]
A_DDR_BA0_HSS
R3354 C3355 A_DDR_D7 RXE_D3P TCON_WP
171 LVA3P 100
33 0.047u COMP1_YINP A_DDR_BA1_HSS MDATA[7]
COMP1_Y A_DDR_BA1_HSS DDR_VREF
R3367 C3376 A_DDR_D0 R3305 172 LVA4M 99
0 1000P COMP1_SOGIN MDATA[0]
F
A_DDR_BA2_HSS 1K
R3355 A_DDR_BA2_HSS R3303 F
C3356 LVA4P
COMP1_PbINP 1K C3307 C3354 173 MVREF 98
33 0.047u
COMP1_Pb 1000P
R3356 A_DDR_A0 A_DDR_D2 F 0.1u
C3359 A_DDR_A0 CZB Pure NC Pin NC
33 0.047u COMP1_PrINP CZB 174 MDATA[2] 97
COMP1_Pr TO MAIN9(AMP)
R3371 A_DDR_A1
C3374 A_DDR_A1 AD_SEL
COMP1_YINM 175 AVDD_DDR PWM2 96 L_MUTE
68 0.047u C3313 L_MUTE
A_DDR_A2 A_DDR_D5 USB_D0P
A_DDR_A2 0.1u USB1_DP
176 MDATA[5] 95
A_DDR_A3 LINE_OUT_L
A_DDR_CLKP_400MHz USB_D0N MONITOR_L
PC input A_DDR_A3
177 MCLK USB1_DM 94 R3361
A_DDR_A4 1K
R3359 C3368 IF_SW
A_DDR_A4 GPIO38 93
33 0.047u PC_GINP 178 AVDD_DDR LINE_OUT_R
PC_G MONITOR_R
R3372 C3377 A_DDR_A5 A_DDR_CLKN_400MHz LED_R R3362
A_DDR_A5 GPIO37 92
0 1000P PC_SOGIN 179 MCLKZ 1K
C3378 R3364 C3380 R3368
R3360 A_DDR_A6 A_DDR_ODT_HSS SPI_WP
C3369 A_DDR_A6 GPIO36 220P 220K 220P 220K
33 0.047u PC_BINP 180 ODT 91
PC_B
R3358 A_DDR_A7 A_DDR_RAS#_HSS I2S_OUT_SCLK
C3367 A_DDR_A7 I2S_OUT_BCK
33 0.047u PC_RINP 181 RASZ 90
PC_R
R3373 A_DDR_A8 A_DDR_CAS#_HSS I2S_OUT_MCLK
C3375 A_DDR_A8 I2S_OUT_MCK
68 0.047u PC_GINM 182 CASZ 89
A_DDR_A9 A_DDR_A0 HP_L_MUTE
A_DDR_A9 183 GPIO28 88 C3342
MADR[0]
0.1u
PC_HSYNC_IN
PC_HSYNC_IN A_DDR_A10
A_DDR_A10 A_DDR_A2
184 MADR[2]
*IC3301 VDDP 87 I2S_OUT_MCLK
R3340
100
C3314 TP3001 I2S_MCLK
PC_VSYNC_IN A_DDR_A11 RH-IXD459WJQZQ R3341
A_DDR_A11 0.1u VDDC
PC_VSYNC_IN 185 AVDD_DDR 86 I2S_OUT_SCLK 100
C3343 R3376 I2S_SCLK
A_DDR_A12 0 R3342
A_DDR_A12 A_DDR_A4 0.1u TCON_WP
186 MADR[4] SPDIFO 85 I2S_OUT_LRCLK 100
E CVBS_AUD_L
C3360
2.2u
10V
KZA115WJ
AUDIO input
AUD_L0
A_DDR_ODT_HSS
A_DDR_ODT_HSS A_DDR_A6
187 MADR[6] MST6003VS GPIO26 84
S_STBY_
I2S_OUT_DAT
R3344
100
I2S_LRCLK
I2S_DAT
CVBS_AUD_L A_DDR_RAS#_HSS A_DDR_A8 L_MUTE
A_DDR_RAS#_HSS 188 GPIO25 83
C3363 10V MADR[8]
CVBS_AUD_R 2.2u KZA115WJ AUD_R0 S_RESET
CVBS_AUD_R A_DDR_CAS#_HSS A_DDR_A11 R3431
A_DDR_CAS#_HSS HP_PLUG
189 MADR[11] GPIO24 82 S_STBY_ 1K
C3315 10V S_STBY
COMP_AUD_L AUD_L1 A_DDR_CLKEN I2S_OUT_DAT
2.2u KZA115WJ A_DDR_CLKEN I2S_OUT_SD
COMP_AUD_L 190 MADR[13] 81
C3316 10V A_DDR_WE#_HSS
COMP_AUD_R 2.2u KZA115WJ AUD_R1 A_DDR_WE#_HSS I2S_OUT_WS
I2S_OUT_LRCLK
COMP_AUD_R 191 VDDC 80
C3309
A_DDR_CLKP_400MHz DDCR_DAT
C3372 10V A_DDR_CLKP_400MHz 0.1u TAGC
T_AGC
PC_AUD_L 2.2u KZA115WJ AUD_L2 192 DDCR_DA 79
PC_AUD_L
A_DDR_CLKN_400MHz
C3373 10V A_DDR_CLKN_400MHz SIFM
SIFM
PC_AUD_R 2.2u KZA115WJ AUD_R2 193 VDDP 78 R3322
PC_AUD_R C3310 0
10K
R3346
DDCR_CLK 0.1u SIFP
SIFP TO MAIN10(POWER)
194 DDCR_CK 77
FB3312 C3348
A192WJ 0.1u FB3314 LAMP_ERR
195 GND AVDD_PGA 76 LAMP-ERR
A192WJ
USB_D0P VIFP
196 VIFP 75
USB0_DM
USB_D0N VIFM
197 USB0_DP VIFM 74
INV_POW
C3346 INV_POW
FB3301 198 PGA_COM 73
AVDD_ALIVE 0.1u
A192WJ C3317
Q3304 VS FB3315 PWM0_OFL
C3319 0.1u A192WJ PWM0_OFL
RT1N141C R3369 199 BYPASS
AVDD_REF 72
WP_CTRL 1u
10K
200 AVDD_DMPLL 71
D
GND
C3347 FB3316
UART_DEBUG_TX SPI_SCLK 0.1u A192WJ
C3379 201 XOUT 70
SCK
0.1u R3347
UART_DEBUG_RX SPI_SDI_DAT C3358
10V 202 XIN 69 470
SDI 10P
3 4
POW_CHK SPI_SDO_DAT
1 VCC 8 203 SDO NC 68
UART_232C_TX
SPI_CS0N 2 1
204 SCZ
Pure NC Pins NC 67
UART_232C_RX
2 7 R3343 X3301
KEY1
2.7K 205 NC 66
SAR0
24MHz
HP_PLUG KEY2 HP_OUT_0R C3357 I2C_CLK
206 AUOUTR0 65 SCA239WJQZ 10P 3 4
SAR1
3 6
TEMP HP_OUT_0L I2C_DAT
207 SAR2 AUOUTL0 64 1 2
C3344 PSW_IN LINE_OUT_R
4 GND 5 0.01u 208 GPIO10 AUOUTR1 63 DDCR_CLK R3350
TO MAIN9(AUDIO_AMP) 3 4 2.2K
TH3301 R3326
DDCA_CLK LINE_OUT_L
209 DDCA_CK AUOUTL1 62
M1103J15 DDCR_DAT 10
FB3317 1 2
IC3303 DDCA_DAT
210 DDCA_DA AVDD_AU33 61
A192WJ
HC2G66DP
HP_L_MUTE LED_G
211 GPIO6 AUR4 60
C3345
0.1u
HP_OUT_0L USB_PLUG AUL4
HP_L 212 GPIO7 59
R3319 3 4
1K EEP_WP
AD_SEL 213 GPIO8 AUR3 58
HP_OUT_0R 1 2
HP_R HPD_+5V_IN AUL3
C R3320 214 GPIO9 57

UART_DEBUG_RX R3351
1K
R3301 C3301 R3313 C3303 RC AUD_R2 4.7K
215 IRIN AUR2 56
220K 220P 220K 220P
UART_DEBUG_TX
HDMI_CEC AUD_L2
216 CEC AUL2 55
Pure NC Pins
AVDD_AU25
DDCDA_DA
DDCDA_CK
HOTPLUGA
CVBSOUT0
AVDD_126
HWRESET
DDCA_CLK
AVDD_25
AVDD_33
AVDD_33
RXACKN
RXACKP
HSYNC0
4
VSYNC0
3
SOGIN0
SOGIN1
AUVAG
AUVRP
IC CONFIGURATION
RXA0N
CVBS4
RXA0P
RXA2N
RXA1N
RXA1P
CVBS2
RXA2P
CVBS3
CVBS1
CVBS0
GIN0M
R3329
GIN1M
GIN0P
RIN0P
VCOM
BIN0P
VDDC
GIN1P
TO MAIN2(HDMI-TERM)
RIN1P
BIN1P
AUR0
AUR1
GND
AUL1
AUL0
GND
ARC
DDCA_DAT 10
NC
NC
NC
NC
NC
NC
NC
NC
NC
1 2
HDMI0_CLKN R3323 R3324 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Q3302 22K
4.7K R3308
LTC014EEB C3365 4.7K
HDMI0_CLKP TL3302 10u C3364
VS C3325 10u
16V
R3335
R3331
R3334
R3330
R3332
R3327
R3328
R3333
HW_RESET TP3304
0
0
0
0
0
HDMI0_D0N 0.047u
C3371 C3370
R3325 0.1u 0.1u R3310
HDMI0_D0P 1K 4.7K
C3323 C3328 C3332 C3334 C3338 C3339

HDMI0_D1N
A192WJ
FB3310
C3330 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u

R3312
0.01u
HDMI0_D1P 4.7K
CZB
56
R3306
HDMI0_D2N
R3315
HDMI0_D2P FB3311 4.7K
FB3309
A192WJ
A192WJ
FB3305
FB3306
A192WJ
A192WJ
C3329
GND
0.1u
NC
3
10V
HDMI_DAT
VDD
B
2
HDMI_CLK
OUT
1
5
CT
HPD_CTRL
EEP_WP
HPD_+5V_IN
IC3306 WP_CTRL
WP_CTRL
BU4229G
6 5 4
Q3301
HDMI_CEC RN4983
HDMI_ARC
1 2 3
RCA_CVBS1_IN
RCA_CVBS2_IN
COMP1_SOGIN
PC_HSYNC_IN
COMP1_PbINP
PC_VSYNC_IN
COMP1_PrINP
COMP1_YINM
COMP1_YINP
HDMI0_CLKN
HDMI0_CLKP
HDMI0_D0N
HDMI0_D1N
HDMI0_D2N
HDMI0_D0P
HDMI0_D1P
HDMI0_D2P
HPD_CTRL
HDMI_ARC
PC_SOGIN
HDMI_DAT
HDMI_CLK
PC_GINM
PC_GINP
PC_RINP
PC_BINP
AUD_R0
AUD_R1
AUD_L0
AUD_L1
VCOM0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–5

MAIN5 (CPU)
TO MAIN10(POWER)
R3337
CPU BU3.3V : 5.6mA(Max) 33K
BU+3.3V
4
D+2.5V
R3321
2.7K
D+3.3V
3
D+1.8V
CPU BU1.26V : 23.9mA(Max)

D+1.26V
D+5V
H PANEL_POW
AC_CTRL
RC
R3339 100
TO MAIN11(KEY)
R/C
TO MAIN6(DDR)
POW_CHK LED_G
FB3308
INV_POW
AC_CTRL
S_RESET
PWM0_OFL
LAMP_ERR
A_DDR_D9
A_DDR_D6
A_DDR_D1
A_DDR_D3
A_DDR_D4
IR_PASS
A_DDR_A1
A_DDR_A3
A_DDR_A5
A_DDR_A7
A_DDR_A9
A_DDR_DQM0
A_DDR_DQM1
A_DDR_D14
A_DDR_D12
A_DDR_D11
A_DDR_A10
A_DDR_A12
A192WJ
A_DDR_DQS0N
A_DDR_DQS0P
A_DDR_CLKEN
A_DDR_WE#_HSS
DDR_VREF FB3313 LED_R

A_DDR_BA1_HSS
A_DDR_BA0_HSS
A_DDR_BA2_HSS
DDR_VREF FB3302 FB3303 FB3304

A192WJ A192WJ
A192WJ A192WJ
A_DDR_DQM0 FB3307
R3353
A_DDR_DQM0
R3336
A192WJ
10K
R3377
10K
R3385 C3341
TO MAIN1(TUNER) A_DDR_DQM1 0
A_DDR_DQM1 0 10u
C3302 16V
C3304 C3306
VIFP A_DDR_DQS0N 10u KZA837WJQZ R3338
A_DDR_DQS0N 16V 0.1u 0.1u
1K
KZA837WJQZ
%35739
VIFM A_DDR_DQS0P
A_DDR_DQS0P KEY1
4 3 KEY_1
TP3308
SIFP A_DDR_DQS1N
A_DDR_DQS1N C3318 KEY2
2 1 KEY_2
10u
SIFM A_DDR_DQS1P 16V
RXE_D0N
RXE_D0P
A_DDR_DQS1P
KZA837WJQZ TP3305
PSW_IN
A_DDR_D0 PSWIN
I2C_CLK A_DDR_D0
R3345
A_DDR_D1 C3336 1K
I2C_DAT A_DDR_D1 0.1u TO MAIN8(PANEL) C3349
0.1u
A_DDR_D2 10V
IF_SW A_DDR_D2 RXE_D0P
R3302 A_DDR_D3 C3351 C3352 C3353

A_DDR_D3 RXE_D0N
5.6K 100P 100P 100P
0.1u
G TAGC
R3349
T_AGC
A_DDR_D4
A_DDR_D4 C3320
0.1u
C3321
2.2u
C3322
0.1u
C3324
0.1u
C3326
0.1u
C3327
0.1u
C3331
0.1u
C3333
0.1u
C3335
0.1u RXE_D1P
CCZ CCZ CCZ
C3337
0 A_DDR_D5
A_DDR_D5 RXE_D1N
C3361 C3362
A_DDR_D6
0.022u 0.1u A_DDR_D6 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 RXE_D2P
C3340
A_DDR_D7
A_DDR_D7 0.1u
PWM1
PWM0
VDDC
VDDC
WEZ
VDDP
DQSL
RXE_D2N
DQMU
DQML
MCLKE
DQSLZ
LVB0M
LVB1M
LVB2M
LVB3M
LVB4M
LVB0P
LVB1P
LVB2P
LVB3P
LVB4P
LVA0M
LVBCKM
LVA0P
R3430
AVDD_MOD
LVBCKP
DVDD_DDR
GPIO77
GPIO76
GPIO75
GPIO74
AVDD_DDR
AVDD_DDR
AVDD_DDR
AVDD_DDR
MADR[1]
MADR[3]
MADR[5]
MADR[7]
MADR[9]
MADR[12]
A_DDR_D8
AVDD_LPLL
BADR[1]
BADR[0]
BADR[2]
C3311 10K
MDATA[9]
MDATA[6]
MDATA[1]
MDATA[3]
MDATA[4]
MADR[10]
A_DDR_D8
MDATA[14]
MDATA[12]
MDATA[11]
0.1u RXE_CLKP TO MAIN7(FLASH)

AVDD_ AVDD_MOD
USB_PLUG A_DDR_D9 163 MEMPLL 108 SPI_CS0N D3301 SPI_CZ
TP3307
A_DDR_D9 SPI_CZ
RXE_CLKN DA1010
A_DDR_DQS1P RXE_D1N R3363
R3316 164 LVA1M 107
C3350 A_DDR_D10 DQSU SPI_SCLK 100 SPI_CLK
33 0.047u RCA_CVBS2_IN A_DDR_D10 RXE_D3P SPI_CLK
A_DDR_DQS1N RXE_D1P R3365
TO MAIN3(TERMINAL) A_DDR_D11 165 QDSUZ
LVA1P 106 SPI_SDI_DAT 100 SPI_DI_DAT
A_DDR_D11 SPI_DI_DAT
RXE_D3N
A_DDR_D15 RXE_D2N R3366
CVBS input A_DDR_D12 166 MDATA[15] LVA2M 105 SPI_SDO_DAT 100 SPI_DO_DAT
A_DDR_D12 SPI_DO_DAT
R3304 C3308 A_DDR_D8 RXE_D2P I2C_DAT
167 LVA2P 104
33 0.047u RCA_CVBS1_IN A_DDR_D13 MDATA[8]
CVBS1 A_DDR_D13 I2C_CLK
RXE_CLKN
168 LVACKM 103 I2C_CLK
A_DDR_D14 AVDD_DDR
C3366 A_DDR_D14 C3312 I2C_DAT
R3357 68 0.047u VCOM0 A_DDR_D10 0.1u RXE_CLKP
169 LVACKP 102
A_DDR_D15 MDATA[10]
A_DDR_D15 SPI_WP
Component input A_DDR_D13 RXE_D3N
170 LVA3M 101
A_DDR_BA0_HSS MDATA[13]
A_DDR_BA0_HSS
R3354 C3355 A_DDR_D7 RXE_D3P TCON_WP
171 LVA3P 100
33 0.047u COMP1_YINP A_DDR_BA1_HSS MDATA[7]
COMP1_Y A_DDR_BA1_HSS DDR_VREF
F R3367
0
R3355
C3376
1000P
C3356
COMP1_SOGIN
A_DDR_BA2_HSS
A_DDR_BA2_HSS
A_DDR_D0
R3303 F
R3305
1K
172 MDATA[0] LVA4M 99
COMP1_PbINP C3354 173 MVREF LVA4P 98

33 0.047u 1K C3307
COMP1_Pb 1000P
R3356 A_DDR_A0 A_DDR_D2 F 0.1u
C3359 A_DDR_A0 CZB Pure NC Pin NC
33 0.047u COMP1_PrINP CZB 174 MDATA[2] 97
COMP1_Pr TO MAIN9(AMP)
R3371 A_DDR_A1
C3374 A_DDR_A1 AD_SEL
COMP1_YINM 175 AVDD_DDR PWM2 96 L_MUTE
68 0.047u C3313 L_MUTE
A_DDR_A2 A_DDR_D5 USB_D0P
A_DDR_A2 0.1u USB1_DP
176 MDATA[5] 95
LINE_OUT_L
A_DDR_A3 A_DDR_CLKP_400MHz USB_D0N MONITOR_L
PC input A_DDR_A3
177 MCLK USB1_DM 94 R3361
A_DDR_A4 1K
R3359 C3368 IF_SW
A_DDR_A4 GPIO38 93
33 0.047u PC_GINP 178 AVDD_DDR LINE_OUT_R
PC_G MONITOR_R
R3372 C3377 A_DDR_A5 A_DDR_CLKN_400MHz LED_R R3362
A_DDR_A5 GPIO37 92
0 1000P PC_SOGIN 179 MCLKZ 1K
C3378 R3364 C3380 R3368
R3360 A_DDR_A6 A_DDR_ODT_HSS
C3369 A_DDR_A6 SPI_WP 220P 220P 220K
PC_BINP 180 ODT GPIO36 91 220K
33 0.047u
PC_B
R3358 A_DDR_A7 A_DDR_RAS#_HSS I2S_OUT_SCLK
C3367 A_DDR_A7 I2S_OUT_BCK
33 0.047u PC_RINP 181 RASZ 90
PC_R
R3373 A_DDR_A8 A_DDR_CAS#_HSS I2S_OUT_MCLK
C3375 A_DDR_A8 I2S_OUT_MCK
68 0.047u PC_GINM 182 CASZ 89
A_DDR_A9 A_DDR_A0
A_DDR_A9 C3342 HP_L_MUTE
183 MADR[0] GPIO28 88
0.1u
PC_HSYNC_IN
PC_HSYNC_IN A_DDR_A10
A_DDR_A10 A_DDR_A2
184 MADR[2]
*IC3301 VDDP 87 I2S_OUT_MCLK
R3340
100
C3314 TP3001 I2S_MCLK
PC_VSYNC_IN A_DDR_A11 RH-IXD454WJQZQ R3341
A_DDR_A11 0.1u VDDC
PC_VSYNC_IN 185 AVDD_DDR 86 I2S_OUT_SCLK 100
E
C3343 R3376 I2S_SCLK
A_DDR_A12 0 R3342
A_DDR_A12 A_DDR_A4 0.1u TCON_WP
186 MADR[4] SPDIFO 85 I2S_OUT_LRCLK
AUDIO input 100
I2S_LRCLK
A_DDR_ODT_HSS A_DDR_A6 S_STBY_ R3344
A_DDR_ODT_HSS
CVBS_AUD_L
C3360 10V
AUD_L0
187 MADR[6] MST6100VS GPIO26 84 I2S_OUT_DAT 100
I2S_DAT
2.2u KZA115WJ A_DDR_RAS#_HSS
CVBS_AUD_L A_DDR_A8 L_MUTE
A_DDR_RAS#_HSS 188 GPIO25 83
C3363 10V MADR[8]
CVBS_AUD_R 2.2u KZA115WJ AUD_R0 S_RESET
CVBS_AUD_R A_DDR_CAS#_HSS A_DDR_A11 R3431
A_DDR_CAS#_HSS HP_PLUG
189 MADR[11] GPIO24 82 S_STBY_ 1K
C3315 10V S_STBY
COMP_AUD_L AUD_L1 A_DDR_CLKEN I2S_OUT_DAT
2.2u KZA115WJ A_DDR_CLKEN I2S_OUT_SD
COMP_AUD_L 190 MADR[13] 81
C3316 10V A_DDR_WE#_HSS
COMP_AUD_R 2.2u KZA115WJ AUD_R1 A_DDR_WE#_HSS I2S_OUT_LRCLK
COMP_AUD_R 191 VDDC I2S_OUT_WS 80
C3309
A_DDR_CLKP_400MHz DDCR_DAT
C3372 10V A_DDR_CLKP_400MHz 0.1u T_AGC
PC_AUD_L AUD_L2 192 DDCR_DA TAGC 79
2.2u KZA115WJ
PC_AUD_L
A_DDR_CLKN_400MHz SIFM
C3373 10V A_DDR_CLKN_400MHz SIFM
PC_AUD_R 2.2u KZA115WJ AUD_R2 193 VDDP 78 R3322
PC_AUD_R C3310 0
10K
R3346
DDCR_CLK 0.1u SIFP
SIFP TO MAIN10(POWER)
194 DDCR_CK 77
FB3312 C3348
A192WJ 0.1u FB3314 LAMP_ERR
195 GND AVDD_PGA 76 LAMP-ERR
A192WJ
USB_D0P VIFP
196 VIFP 75
USB0_DM
USB_D0N VIFM
197 USB0_DP VIFM 74
INV_POW
C3346 INV_POW
FB3301 198 PGA_COM 73
AVDD_ALIVE 0.1u
A192WJ C3317
Q3304 VS FB3315 PWM0_OFL
C3319 0.1u A192WJ PWM0_OFL
RT1N141C AVDD_REF
D R3369 199 BYPASS 72

WP_CTRL 1u
10K
200 GND AVDD_DMPLL 71
C3347 FB3316
UART_DEBUG_TX SPI_SCLK 0.1u A192WJ
C3379 201 XOUT 70
SCK
0.1u R3347
UART_DEBUG_RX SPI_SDI_DAT C3358
10V 202 XIN 69 470
SDI 10P
3 4
POW_CHK SPI_SDO_DAT
1 VCC 8 203 SDO NC 68
UART_232C_TX
SPI_CS0N 2 1
204 SCZ Pure NC Pins NC 67
UART_232C_RX
2 7 R3343 X3301
KEY1
2.7K 205 SAR0 NC 66
24MHz
HP_PLUG KEY2 HP_OUT_0R C3357 I2C_CLK
206 AUOUTR0 65 SCA239WJQZ 10P 3 4
SAR1
3 6
TEMP HP_OUT_0L I2C_DAT
207 SAR2 AUOUTL0 64 1 2
C3344 PSW_IN LINE_OUT_R
4 GND 5 0.01u 208 AUOUTR1 63 R3350
GPIO10 DDCR_CLK
TO MAIN9(AUDIO_AMP) 3 4 2.2K
TH3301 R3326
DDCA_CLK AUOUTL1 LINE_OUT_L
M1103J15 209 DDCA_CK 62 DDCR_DAT 10
FB3317 1 2
IC3303 DDCA_DAT
210 DDCA_DA AVDD_AU33 61
A192WJ
HC2G66DP
HP_L_MUTE LED_G
211 AUR4 60
GPIO6 C3345
0.1u
HP_OUT_0L USB_PLUG
HP_L 212 AUL4 59
GPIO7
R3319 3 4
C
1K EEP_WP
AD_SEL 213 AUR3 58
GPIO8
HP_OUT_0R 1 2
HP_R HPD_+5V_IN
R3320 214 AUL3 57
GPIO9
UART_DEBUG_RX R3351
1K
R3301 C3301 R3313 C3303 RC AUD_R2 4.7K
215 IRIN AUR2 56
220K 220P 220K 220P
UART_DEBUG_TX
HDMI_CEC AUD_L2
216 CEC AUL2 55
Pure NC Pins
AVDD_AU25
DDCDA_DA
DDCDA_CK
HOTPLUGA
CVBSOUT0
AVDD_126
HWRESET
DDCA_CLK
AVDD_25
AVDD_33
AVDD_33
RXACKN
RXACKP
HSYNC0
4
VSYNC0
3
SOGIN0
SOGIN1
AUVAG
AUVRP
IC CONFIGURATION
RXA0N
CVBS4
RXA0P
RXA2N
RXA1N
RXA1P
CVBS2
RXA2P
CVBS3
CVBS1
CVBS0
GIN0M
R3329
GIN1M
GIN0P
RIN0P
VCOM
BIN0P
VDDC
GIN1P
TO MAIN2(HDMI-TERM)
RIN1P
BIN1P
AUR0
AUR1
GND
AUL1
AUL0
GND
ARC
DDCA_DAT 10
NC
NC
NC
NC
NC
NC
NC
NC
NC
1 2
HDMI0_CLKN R3323 R3324 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Q3302 22K
4.7K R3308
LTC014EEB C3365 4.7K
HDMI0_CLKP TL3302 10u C3364
VS C3325 10u
16V
R3335
R3331
R3334
R3330
R3332
R3327
R3328
R3333
HW_RESET TP3304
0
0
0
0
0
HDMI0_D0N 0.047u
C3371 C3370
R3325 0.1u 0.1u R3310
HDMI0_D0P 1K 4.7K
C3323 C3328 C3332 C3334 C3338 C3339

HDMI0_D1N
A192WJ
FB3310
C3330 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u

R3312
0.01u
HDMI0_D1P 4.7K
CZB
56
R3306
HDMI0_D2N
R3315
HDMI0_D2P FB3311 4.7K
FB3309
A192WJ
A192WJ
FB3305
FB3306
A192WJ
A192WJ
C3329
B
GND
0.1u
NC
3
10V
HDMI_DAT
VDD
2
HDMI_CLK
OUT
1
5
CT
HPD_CTRL
EEP_WP
HPD_+5V_IN
IC3306 WP_CTRL
WP_CTRL
BU4229G
6 5 4
Q3301
HDMI_CEC RN4983
HDMI_ARC
1 2 3
RCA_CVBS1_IN
RCA_CVBS2_IN
COMP1_SOGIN
PC_HSYNC_IN
COMP1_PbINP
PC_VSYNC_IN
COMP1_PrINP
COMP1_YINM
COMP1_YINP
HDMI0_CLKN
HDMI0_CLKP
HDMI0_D0N
HDMI0_D1N
HDMI0_D2N
HDMI0_D0P
HDMI0_D1P
HDMI0_D2P
HPD_CTRL
HDMI_ARC
PC_SOGIN
HDMI_DAT
HDMI_CLK
PC_GINM
PC_GINP
PC_RINP
PC_BINP
A
AUD_R0
AUD_R1
AUD_L0
AUD_L1
VCOM0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–6

• MAIN Unit-6/11
MAIN6(DDR)
I
TO MAIN10(POWER) FL3501
NA119WJ
010
D+1.8V
C3508
10u C3505
16V 0.1u K
KZA837WJQZ 10V
H
R3526 R3525
1K 1K
F
TO MAIN5(CPU) F
VREF_DDR_0.9V
A_DDR_DQM0
A_DDR_DQM1
A_DDR_DQS0N R3501 R3514 1 2 3 7 8 9

DDRA_DQS1N
56 56
C3502 C3507
A_DDR_DQS0P A_DDR_D7 DDRA_D7 A_DDR_D11 DDRA_D11 0.1u K 0.1u
7 8 7 8 K
10V
G A_DDR_DQS1N A_DDR_D0 DDRA_D0 A_DDR_D12 DDRA_D12
A1
VDD
A2
NC
A3
VSS
A
A7
VSSQ
A8
/UDQS
A9
VDDQ
10V
5 6 5 6 DDRA_DQM1 DDRA_DQS1P
A_DDR_DQS1P A_DDR_D2 DDRA_D2 A_DDR_D9 DDRA_D9 DDRA_D14 DDRA_D15
3 4 3 4
A_DDR_D0 A_DDR_D5 DDRA_D5 A_DDR_D14 DDRA_D14
1 2 1 2 B1 B2 B3 B B7 B8 B9
A_DDR_D1 DQ14 VSSQ UDM UDQS VSSQ DQ15
DDRA_D9 DDRA_D8
R3504 R3515
A_DDR_D2 56
56
A_DDR_DQS0N DDRA_DQS0N C3510
A_DDR_D4 DDRA_D4 0.1u K
A_DDR_D3 7 8 C1 C2 C3 C C7 C8 C9
10V
VDDQ DQ9 VDDQ VDDQ DQ8 VDDQ
R3505 A_DDR_D3 DDRA_D3 DDRA_D11 DDRA_D10
A_DDR_D4 5 6
56
A_DDR_DQS0P DDRA_DQS0P DDRA_D12 DDRA_D13
A_DDR_D1 DDRA_D1
A_DDR_D5 3 4
F A_DDR_D6
R3506 A_DDR_D6 DDRA_D6 D1 D2 D3 D D7 D8 D9
56 1 2 DQ12 VSSQ DQ11 DQ10 VSSQ DQ13
A_DDR_DQM0 DDRA_DQM0
DDRA_DQS0N
A_DDR_D7
R3516
56 C3511
R3507
A_DDR_D8 0.1u K
56 E1 E2 E3 E E7 E8 E9
A_DDR_DQS1N DDRA_DQS1N A_DDR_D15 DDRA_D15 10V
7 8 VDD NC VSS VSSQ /LDQS VDDQ
A_DDR_D9 DDRA_DQM0 DDRA_DQS0P
A_DDR_D8 DDRA_D8
R3508 5 6 DDRA_D6 DDRA_D7
A_DDR_D10
56
A_DDR_DQS1P DDRA_DQS1P A_DDR_D10 DDRA_D10
3 4 F
A_DDR_D11 F1 F2 F3 F7 F8 F9
A_DDR_D13 DDRA_D13 DQ6 VSSQ LDM LDQS VSSQ DQ7
R3509 1 2 DDRA_D1
A_DDR_D12 DDRA_D0
56
A_DDR_DQM1 DDRA_DQM1
A_DDR_D13 C3512
E C3503
0.1u K G1 G2 G3 G G7 G8 G9 0.1u K
A_DDR_D14 10V 10V
VDDQ DQ1 VDDQ VDDQ DQ0 VDDQ
A_DDR_D15
IC3501
DQ4 VSSQ DQ3 IXD361WJQZ DQ2 VSSQ DQ5
H1 H2 H3 H H7 H8 H9
DDRA_D4 DDRA_D5
DDRA_D3 DDRA_D2
VDDL VREF VSS VSSDL CK VDD

C3506
A_DDR_BA0_HSS R3502 0.1u J1 J2 J3 J J7 J8 J9
K
56 R3519 10V C3509
R3527
56 0.1u K 100
A_DDR_BA1_HSS A_DDR_WE#_HSS DDRA_WE#_HSS A_DDR_CLKP_400MHz DDRA_CLKP_400MHz 10V DDRA_CLKP_400MHz
1 2
D A_DDR_BA2_HSS A_DDR_CLKEN
3 4
DDRA_CLKEN R3520 CKE /WE /RAS /CK ODT
56 K2 K3 K7 K8 K9
A_DDR_CLKN_400MHz DDRA_CLKN_400MHz
K
A_DDR_A0 A_DDR_BA1_HSS DDRA_BA1_HSS DDRA_ODT_HSS
5 6 DDRA_CLKEN R3528
100 DDRA_CLKN_400MHz
A_DDR_A1 A_DDR_BA0_HSS DDRA_BA0_HSS DDRA_WE#_HSS
7 8 R3517 DDRA_RAS#_HSS
56 NC(BA2) BA0 BA1 /CAS /CS
A_DDR_A2
A_DDR_A0 DDRA_A0 L1 L2 L3 L L7 L8
1 2 DDRA_BA2_HSS
A_DDR_A3
A_DDR_CAS#_HSS DDRA_CAS#_HSS DDRA_BA0_HSS
3 4 DDRA_CAS#_HSS
A_DDR_A4 DDRA_BA1_HSS
R3511 A_DDR_RAS#_HSS DDRA_RAS#_HSS A10 A1 A2 A0 VDD C3517
5 6
A_DDR_A5 56 M2 M3 M7 M8 M9 0.1u
A_DDR_A1 DDRA_A1 M 10V
A_DDR_ODT_HSS DDRA_ODT_HSS
7 8 DDRA_A10
A_DDR_A6 DDRA_A0
R3512
56 DDRA_A1 DDRA_A2
C A_DDR_A7
A_DDR_A10 DDRA_A10
R3518 VSS A3 A5 A6 A4
56
R3513 N1 N2 N3 N N7 N8
A_DDR_A8 A_DDR_A8 DDRA_A8
56 1 2
A_DDR_A3 DDRA_A3 DDRA_A3 DDRA_A4
A_DDR_A9 A_DDR_A6 DDRA_A6 DDRA_A5 DDRA_A6
3 4
A7 A9 A11 A8 VSS
A_DDR_A10 R3503 A_DDR_A4 DDRA_A4
56 5 6 P2 P3 P P7 P8 P9
A_DDR_A11 A_DDR_A5 DDRA_A5 A_DDR_A2 DDRA_A2 DDRA_A7
1 2 7 8 DDRA_A8
DDRA_A9 DDRA_A11
A_DDR_A12 A_DDR_A7 DDRA_A7
3 4 VDD A12 NC NC NC
R3521 C3504
A_DDR_A9 DDRA_A9 0.1u R1 R2 R3 R R7 R8
56 K
5 6 A_DDR_A11 DDRA_A11 10V
A_DDR_ODT_HSS
A_DDR_A12 DDRA_A12
7 8
B A_DDR_RAS#_HSS
DDRA_A12
A_DDR_CAS#_HSS
A_DDR_CLKEN
A_DDR_WE#_HSS
A_DDR_CLKP_400MHz
A_DDR_CLKN_400MHz
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–7

MAIN7 (FLASH)
I
TO MAIN10(POWER)
BU+3.3V
G
SPI_WP
SPI_CZ
SPI_DO_DAT
TO MAIN5(CPU)
SPI_WP
R3101 SPI_CLK
4.7K
F SPI_CZ
3 4
SPI_DI_DAT
SPI_WP
1 2
SPI_DO_DAT
R3104
10
4 3 2 1
1 2 I2C_CLK
GND WP SO/SIO1 CS
R3103
I2C_DAT
E *IC3101 4.7K 3 4
RH-IXD463WJQZQ R3105
10
SCLK
SI/SIO0 HOLD VCC
3.3 0 3.3 3.3 3.3 0 3.3 3.3
C3102 C3103
5 6 7 8 0.1u 8 7 6 5 0.1u 8 7 6 5
10V 10V
C3101 VCC WP SCL SDA
0.1u
10V
D CZB IC3102 0
R3102
IC3103
BR24T28F IXD110WJQZ
SPI_DI_DAT
A0 A1 A2 A0 A1 A2 GND
SPI_CLK
1 2 3 4 1 2 3 4
0 0 0 0 0 0 0 0
C
For DATA For HDCP Key
I2C Address at A4 I2C Address at A8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–8

MAIN7 (FLASH)
I
TO MAIN10(POWER)
BU+3.3V
G
SPI_WP
SPI_CZ
SPI_DO_DAT
TO MAIN5(CPU)
SPI_WP
R3101 SPI_CLK
4.7K
F SPI_CZ
3 4
SPI_DI_DAT
SPI_WP
1 2
SPI_DO_DAT
R3104
10
4 3 2 1
1 2 I2C_CLK
GND WP SO/SIO1 CS
R3103
I2C_DAT
E *IC3101 4.7K 3 4
RH-IXD464WJQZQ R3105
10
SCLK
SI/SIO0 HOLD VCC
3.3 0 3.3 3.3 3.3 0 3.3 3.3
C3102 C3103
5 6 7 8 0.1u 8 7 6 5 0.1u 8 7 6 5
10V 10V
C3101 VCC WP SCL SDA
0.1u
10V
D CZB IC3102 0
R3102
IC3103
BR24T28F IXD110WJQZ
SPI_DI_DAT
A0 A1 A2 A0 A1 A2 GND
SPI_CLK
1 2 3 4 1 2 3 4
0 0 0 0 0 0 0 0
C For DATA For HDCP Key

I2C Address at A4 I2C Address at A8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–9

• MAIN Unit-8/11
I
MAIN8 (PANEL)
P3801
NA915WJ
H
@pinCo
TO MAIN10(POWER) TL3806 1 GND
PNL+12V 2 VCC
C3801 VCC
3
D+3.3V 0.1u
CZB VCC
4
TO MAIN5(CPU) 1 VCC 8
G 5 VCC
6 GND
2 7
7 GND
3 6 GND
8
9 GND
4 GND 5
10 SELLVDS
F TL3804
I2C_CLK R3802
*IC3801 10K 11 NC(OS_EN)
TCON_WP
12 NC/TCON_WP
HC2G66DP
I2C_DAT 13 NC/BIST
14 NC/SDA
TL3805
15 NC/SCL
E
16 GND
RXE_D3P 17 RIN3+
RXE_D3N 18 RIN3-
19 GND
RXE_CLKP 20 CLKN+
D RXE_CLKN 21 CLKN-
22 GND
RXE_D2P 23 RIN2+
RXE_D2N 24 RIN2-
25 GND
RXE_D1P 26 RIN1+
C
RXE_D1N 27 RIN1-
28 GND
RXE_D0P 29 RIN0+
RXE_D0N 30 RIN0-
31 GND
B 32 GND
@pinCo
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8 – 10

• MAIN Unit-9/11
MAIN9(AUDIO_AMP)
I
TO MAIN10(POWER)
UR+12.2V
TO MAIN3(TERMINAL)
D+3.3V
D+5V
MON_L_OUT
13V_DET
MON_R_OUT
BU+5V
H HP_L_OUT
HP_R_OUT
CZ
R1910
100K
TL1909
VS
C1905
1u 10V Q1902 C1916
LTC044EEB C1915
0.1u
10u
CZF
16V
5 4 3 2 1
IC1902 C1909 C1910
13
15
14
0.1u
16
NJU72011 10u
16V CZF
4 3
EN
C1920
GND
C1911
AVDD
SGND
OUTL
OUT CD
HPVDD
IC1905 C1922
12
6 7 8 9 10
INL-
1000P 1u 10V 2.2u
50V
C1912 10V
C1902 PST8429U CZB
CPP
11
2
16V 10u
INL+
GND VDD
1u 10V IC1903
C1913
1 2
TPA6132A
PGND
10
3
INR+
R1905
R1908
12K TL1904 1u 10V
10K C1919
C1914
9
CPN
VS
INR-
1u 10V
Q1901 1u
HPVSS
OUTR
G0
LTC044EEB 10V
G1
C1903 R1906 4 3
8
1u CYB 1K R1917 R1918
OUT CD
6.8K 2.2K
IC1904 C1921
F R1907 1K 1000P
50V
C1904 PST8429U CZB
R1901 1u CYB
C1907 C1908 GND VDD C1917
15K
820P 820P 2.2u
1 2 10V
CZ
R1912 R1914
10K 10K
CZ
TO MAIN5(CPU)
L_MUTE
MONITOR_R
R1915 R1916
6.8K 2.2K
MONITOR_L
HP_L_MUTE
E HP_L
HP_R
S_RESET
S_STBY
C1702
10u C1716
25V 0.22u
C1710
KZA838WJQZ
0.1u 25V CKZ
25V CYB
L1701 L1703
C1704
10u 22uH 22uH C1715
C1701 0.1u
25V PB301WJQZ PB301WJQZ 25V
I2S_MCLK 10u CYB
25V KZA838WJQZ
KZA838WJQZ
I2S_DAT C1708 C1712
1u 25V 1u 25V
KZA621WJQZ KZA621WJQZ
D I2S_SCLK
I2S_LRCLK 13.3 5.4 5.4 0 5.4 5.4 13.3

32
31
30
29
28
27
26
C1731
OUTPL
PVSSR
PVDDML
OUTML
PVDDPL
PVSSL
PVSSR
1000P
13.3 0 CYB
AVSS MONO P1701
1
25
C1706 NA961WJ
0.1u
10V
3.3 3.3
VREF GAIN1 4 Lch+
2
24
C1707 R1709
1u 0
10V
3 Lch-
1.66 0
REFA
IC1701 GAIN0
3
23
R1710 2 Rch-
C1705 0 R1715
TP1702
0.1u VHIYDA164DZ-1Y 47K
1.66 0 1 Rch+
DVDD CKMOD
4
22
R1705 R1719
C 0
1.66
MCK MUTEN
0
47K
5
21
R1706 R1716
TP1703
0 47K
1.66 2.4
SDATA PROTN C1732
6
20
R1707 1000P
R1717
0 CYB
TL1901 1.66 3.3 10K
R1711
SCLK SLEEPN
7
19
560K
R1708 R1720
0 22K
4 3 0 0
LRCLK PLIMIT
8
18
OUT CD TP1701
(PWB)
C1718
IC1901 C1901
1000P 0.92 3.3 1000P *R1718
DVSS HOPP 10K
17
9
50V
R1712
PST8429U CZB
PVDDPR
PVDDMR
OUTPR
PVSSR
OUTMR
PVSSR
10K
PVSSR
GND VDD
1 2
10
11
12
13
14
15
16
13.3 5.4 5.4 0 5.4 5.4 13.3

B
C1709 C1713
1u 25V 1u 25V
KZA621WJQZ KZA621WJQZ
C1711 L1702 L1704

0.1u C1714
R1903 R1904 22uH 22uH
3.3K 8.2K 25V PB301WJQZ 0.1u
PB301WJQZ
CYB 25V
CYB
C1717
0.22u
25V CKZ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8 – 11

• MAIN Unit-10/11
MAIN10 (POWER)
I
R9626
4.7K
SC9601
NA911WJ
VS VS Q9605
@pinCo TL9601 Q9604 RT1N141C
RT1N141C
UR12.2V 1
C9601
TL9613
TO MAIN9(AUDIO_AMP)
H UR12.2V 2 10u
25V
R9632
UR12.2V 3 4.7K
TL9602
GND 4
GND UR+12.2V
5 R9625
4.7K
GND 6 TL9603
D+3.3V
PS_ON 7 TL9604 R9602
0 R9636 D+5V
F
LAMP_ERR 8 12K
TL9611 R9603
CZ
0 C9611
R9613
R9616
PWM(OFL) VHD BU+5V

9
12K
10K
TL9612 R9612 0.033u

R9606 R9607 D9606
0 16V
STB 10 47K 12K DB2J317L
R9637
2200P
C9616
@pinCo
3.3K
CZ R9624 VHIRP130N50-5Y
R9620
G 1.6K 51K F
TL9610
D+5V 80mAmax
F IC9607 IC9610 TO MAIN3(TERNIMAL)
8 7 6 5 IC9603 KZA520WJQZ
C9629
3416C33N KZA520WJQZ
RP130N50
C9633
BD9329EF 1u 10V C9631
EN
1u 10V
SS
FB
1u 10V D+5V
COMP
C9636
10u Vin Vout Vin Vout
5
1
1
16V KZA520WJQZ
KZA837WJQZ GND GND
2
2
M+5.6V
GND
On NC On NC
SW
Vin
4
3
4
BS
IC9612 BU+3.3V
1 2 3 4
R9609
L9603 C9623
27 10uH
PB014WJQZ
10u
16V
M+5.6V Vin
S170B50U
NC
3
2.45A 48m KZA837WJQZ TL9605
R9628 KZA761WJQZ
R9635 R9627
IC9608 GND
2
C9610 1 1 1 C9632
0.1u 4.7u 10V D9605
C9624
Vout ON CRS02
1
C9614 10u 1/2W 1/2W 1/2W
25V
F CZB 10u 16V TWF TWF TWF VHD
VIN
4
3
NC
25V KZA837WJQZ R9634

KZA838WJQZ S172B33U 1K TO MAIN1(TUNER)
TL9607
VSS
T+5V
2
KZA761WJQZ
C9626 C9630
4.7u 4.7u 10V D+3.3V
VOUT
10V
ON
5
KZA761WJQZ
TL9609
D+3.3V 600mA
TO MAIN7(FLASH)
R9618 R9630 IC9611 KZA520WJQZ

C9634
4.7K 1 3416C25N 1u 10V BU+3.3V
1/2W
TO MAIN5(CPU) TWF
Vin Vout
1
INV_POW R9631
1
IC9609 GND
C9617
C9612 KZA761WJQZ
F
0.022u
C9627 1/2W TO MAIN2(HDMI-TERM)

E PWM0_OFL
R9615
0.033u
4.7u 10V TWF S170B18U On NC
10K
16V
R9619 R9623 Vin NC
4
LAMP-ERR 680 F 3.9K F D+5V

R9614
1K
C9628
GND
2
4.7u 10V BU+3.3V

KZA067WJ
Vout ON
5
PANEL_POW
8 7 6 5 IC9605
BD9328EF TL9608
EN
SS
FB
COMP
R9601
10K
1.8V 280mA
GND
SW
Vin
BS
1 2 3 4
R9610 L9602
0 10uH
PB014WJQZ
2.45A 48m
TL9606
D+1.26V 600mA
D
C9621 C9622 TO MAIN6(DDR)
C9613 10u 10u
0.01u 16V D+1.8V
16V
K 16V KZA837WJQZ KZA837WJQZ
C9615 TO MAIN5(CPU)
10u
25V D+5V
KZA838WJQZ
D+3.3V
D+1.8V
D+2.5V
D+1.26V
C BU+3.3V
AC_CTRL
POW_CHK
C9602
1u 25V
KZA621WJQZ
R9605
47K
Q9602
TPC6110 R9611 0
TO MAIN8(PANEL)
R9608
4.7K PNL+12V
3
4
C9635 D+3.3V
10u
B 25V
2
5
KZA838WJQZ
6
TO MAIN11(KEY)
Q9601 BU+5V
RT1N141U
BU+3.3V
A
DUNTKF998WE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8 – 12

• MAIN Unit-11/11
MAIN11(KEY/RC)
I
CH-UP CH-DOWN INPUT VOL-UP VOL-DOWN MENU

S101 S102 S103 S104 S106 S107
KA037WJ KA037WJ KA037WJ KA037WJ KA037WJ KA037WJ
H
1
1
3
3
4
4
2
2
G
R101 R103
8.2K 12K
1/16W 1/16W R113 R117
8.2K 12K
1/16W 1/16W
POW
F S105 RMC101
KA037WJ UA108WJQZ
TO MAIN5(CPU) 4 5
1
3
GND GND
TL101
4
KEY_1
TL102
KEY_2
E TL103
VCC GND VOUT
PSWIN 3 2 1
TO MAIN10(POWER)
BU+3.3V
R116
100
R111
BU+5V
10K
Q102
2SC3928AR
D TO MAIN5(CPU)
LED CONT C103
10u
TL104 C102
D102 0.7 CKZ
10u
R/C PXA227WJQZ CKZ
TL105
Green R110
470 0.2
LED_G 0
TL106
LED_R D103
PXA226WJQZ
RED
2.3 0
C R108
1K
Q103
0
2SC3928AR
LED CONT
R105
10K
DUNTKF998WE
(QPWBFFWJZZ)
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8 – 13

8 – 14

PartsGuide
PARTS GUIDE
No. SY1V132LE340M
LCD COLOR TELEVISION
LC-32LE240M
MODELS LC-32LE340M
Note:
The reference numbers on the PWB
are arranged in alphabetical order.
CONTENTS
[1] PRINTED WIRING BOARD [5] LCD PANEL
ASSEMBLIES
[6] SUPPLIED ACCESSORIES
[2] LCD PANEL
[7] PACKING PARTS
[3] DKEYMF998FMG4/5 (MAIN Unit) (NOT REPLACEMENT ITEM)
[4] CABINET AND MECHANICAL

PARTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used

for after sales service only.
The contents are subject to change without notice.
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[1] PRINTED WIRING BOARD ASSEMBLIES

N DUNTKF998FMG4 N V MAIN Unit (LC-32LE340M)
N DKEYMF998FMG5 N V MAIN Unit (LC-32LE240M)
N RUNTKA929WJQZ N V POWER Unit
N RUNTKA927WJZZ N V LED PWB-A
N RUNTKA928WJZZ N V LED PWB-B
[2] LCD PANEL
N R1LK315T3HB00W N V LCD Panel Unit
[3] DKEYMF998FMG4/5 (MAIN Unit)
C102 RC-KZA837WJQZY AB J Capacitor 10 10V Ceramic
C501 VCKYCZ1EB103KY AA J Capacitor 0.01 25V Ceramic
C502 VCCCCZ1HH100DY AB J Capacitor 10p 50V Ceramic
C514 VCCCCZ1HH560JY AB J Capacitor 56p 50V Ceramic
C515 VCCCCZ1HH102JY AA J Capacitor 1000p 50V Ceramic
C526 VCKYCZ1HB102KY AB J Capacitor 1000p 50V Ceramic
C1103 VCKYCZ1AB104KY AB J Capacitor 0.1 10V Ceramic
C1707 VCKYCY1AB105KY AB J Capacitor 1 10V Ceramic
C1708 RC-KZA621WJQZY AA J Capacitor 1 25V Ceramic
C1710 VCKYCY1EB104KY AB J Capacitor 0.1 25V Ceramic
C1716 RC-KZA709WJQZY AA J Capacitor 0.22 25V Ceramic
C1717 RC-KZA709WJQZY AA J Capacitor 0.22 25V Ceramic
C1731 VCKYCY1HB102KY AA J Capacitor 1000p 50V Ceramic
C1732 VCKYCY1HB102KY AA J Capacitor 1000p 50V Ceramic
C1910 VCKYCZ1EF104ZY AA J Capacitor 0.1 25V Ceramic
2
RANK MARK DELIVERY

C1916 VCKYCZ1EF104ZY AA J Capacitor 0.1 25V Ceramic
C1917 RC-KZA115WJZZY AB J Capacitor 2.2 10V Ceramic
C3301 VCKYCZ1HB221KY AA J Capacitor 220p 50V Ceramic
C3319 RC-KZA520WJQZY AA J Capacitor 1 Ceramic
C3361 VCKYCZ1CB223KY AC J Capacitor 0.022 16V Ceramic
3
RANK MARK DELIVERY

C9611 VCKYCZ1CB333KY AA J Capacitor 0.033 16V Ceramic
C9612 VCKYCZ1CB333KY AA J Capacitor 0.033 16V Ceramic
C9613 VCKYCZ1CB103KY AB J Capacitor 0.01 16V Ceramic
C9617 VCKYCZ1CB223KY AC J Capacitor 0.022 16V Ceramic
C9626 RC-KZA761WJQZY AB J Capacitor 4.7 10V Ceramic
C9628 RC-KZA067WJZZY AB J Capacitor 1000p 50V Ceramic
D102 RH-PXA227WJQZY N V Diode PY1111R-TR
D103 RH-PXA226WJQZY N V Diode BR1111R-TR
D510 VHDBAV70+++-1Y AB J Diode BAV70,215
D1101 VHDKDS114E+-1Y AB J Diode KDS114E-RTK/P
D1510 VHDDB2S310L-1Y AB J Diode DB2S31000L
D1516 VHDDB2S310L-1Y AB J Diode DB2S31000L
D3301 VHDDA1010++-1Y AA J Diode DA2J10100L
D9605 VHDCRS02+++-1Y AC J Diode CRS02(TE85L,Q,M)
D9606 VHDDB2J317L-1Y V Diode DB2J31700L
FB503 RBLN-A206WJZZY AA J Ferrite Bead
FB517 RBLN-A369WJZZY AB J Ferrite Bead
FB521 RBLN-0093GEZZY AB J Ferrite Bead
FL1101 RFiLCA072WJQZ V Filter
FL1102 RFiLCA058WJZZ AG J Filter
FL3501 RFiLNA119WJZZY AC J Filter
IC508 VHiBR24T02J-1Y V IC BR24T02FJ-WE2
4
RANK MARK DELIVERY

IC510 VHiS172B50U-1Y V IC S-1172B50-U5T1G
IC1501 VHiBR24T02J-1Y V IC BR24T02FJ-WE2
IC1701 VHiYDA164DZ-1Y V IC YDA164B-QZE2
IC1901 VHiPST8429U-1Y AC J IC IC-PST8429UR
IC1902 VHiNJU72011-1Y AG J IC NJU72011RB2(TE2)
IC1903 VHiTPA6132A-1Y AE J IC TPA6132A2RTER
IC3101 RH-iXD463WJQZQ N V IC iXD463WJ (LC-32LE240M)
IC3101 RH-iXD464WJQZQ N V IC W25Q64CVSSIG (LC-32LE340M)
IC3102 VHiBR24T28F-1Y AE J IC BR24T128F-WE2
IC3103 RH-iXD110WJQZY AG J IC CAT24C08
IC3301 RH-iXD459WJQZQ N V IC MST6003VS-LF-Z1 (LC-32LE240M)
IC3301 RH-iXD454WJQZQ V IC MST6100VS-LF-Z1-SJ (LC-32LE340M)
IC3303 VHiHC2G66DP-1Y AD J IC 74HC2G66DP,125
IC3306 VHiBU4229G+-1Y V IC BU4229G-TR
IC3501 RH-iXD361WJQZQ V IC H5PS5162GFR-S5C
IC3801 VHiHC2G66DP-1Y AD J IC 74HC2G66DP,125
IC9603 VHiBD9329EF-1Y AF J IC BD9329EFJ-E2
IC9605 VHiBD9328EF-1Y AF J IC BD9328EFJ-E2
IC9607 VHi3416C33N-1Y AC J IC MM3416C33NRE
IC9608 VHiS172B33U-1Y AD J IC S-1172B33-U5T1G
IC9609 VHiS170B18U-1Y AE J IC S-1170B18UC-OTDTFG
IC9610 VHiRP130N50-5Y V IC RP130N501B-TR-FE
IC9611 VHi3416C25N-1Y AB J IC MM3416C25NRE
IC9612 VHiS170B50U-1Y AD J IC S-1170B50UC-OUJTFG
J501 QSOCZA284WJQZ AC J Socket
J502 QJAKLA047WJQZ V Jack
J504 QJAKJ0101SEZZ AE J Jack
J506 QJAKJA024WJZZ AD J Jack
L501 RCiLFA154WJZZY AC J Coil
L1103 VPSBNR82JR34NY AB J Peaking 0.82µH
L1701 RCiLPB301WJQZY AC J Coil
P501 QPLGNA338WJZZY AD J Plug
P1701 QPLGNA961WJZZY AD J Plug
P3801 QPLGNA915WJZZY AG J Plug
Q102 VS2SC3928AR-1Y AB J Transistor 2SC3928A-T112V-1R
Q103 VS2SC3928AR-1Y AB J Transistor 2SC3928A-T112V-1R
Q1101 VSDSC2G03//1EY V Transistor DSC2G0300L
Q1105 VSLTC044EEB-1Y AB J Transistor LTC044EEBFS8TL
Q3301 VSRN4983///-1Y AC J Transistor RN4983(TE85L,F)
Q3304 VSRT1N141C/-1Y AB J Transistor RT1N141U-T112-1
Q9601 VSRT1N141U/-1Y AB J Transistor RT1N141U-T111-1
Q9602 VSTPC6110++-1Y AC J Transistor TPC6110(TE85L,F,M)
R101 VRS-CZ1JF822JY AA J Resistor 8.2k 1/16W Metal Oxide
R103 VRS-CZ1JF123JY AA J Resistor 12k 1/16W Metal Oxide
R110 VRS-CZ1JF471JY AA J Resistor 470 1/16W Metal Oxide
R507 VRS-TW2ED101JY AA J Resistor 100 1/4W Metal Oxide
5
RANK MARK DELIVERY

R533 VRS-TQ2EF750JY AA J Resistor 75 1/4W Metal Oxide
R1117 VRS-CZ1JF680JY AB J Resistor 68 1/16W Metal Oxide
R1504 VRK-SA1JF100JY AB J Resistor 10 1/16W Metal Composition
R1516 VRK-SA1JF473JY AC J Resistor 47k 1/16W Metal Composition
R1711 VRS-CZ1JF564JY AB J Resistor 560k 1/16W Metal Oxide
6
RANK MARK DELIVERY

R3303 VRS-CZ1JF102FY AA J Resistor 1k 1/16W Metal Oxide
R3337 VRK-SA1JF333JY AB J Resistor 33k 1/16W Metal Composition
R3338 VRK-SA1JF102JY AB J Resistor 1k 1/16W Metal Composition
R3343 VRS-CZ1JF272FY AA J Resistor 2.7k 1/16W Metal Oxide
R3350 VRK-SA1JF222JY AB J Resistor 2.2k 1/16W Metal Composition
R3351 VRK-SA1JF472JY AA J Resistor 4.7k 1/16W Metal Composition
R3501 VRK-SB1FF560JY V Resistor 56 1/32W Metal Composition
7
RANK MARK DELIVERY

R9611 VRS-CY1JF000JY AA J Resistor 0 1/16W Metal Oxide
R9615 VRS-CZ1JF103FY AB J Resistor 10k 1/16W Metal Oxide
R9616 VRS-CZ1JF103FY AB J Resistor 10k 1/16W Metal Oxide
R9619 VRS-CZ1JF681FY AA J Resistor 680 1/16W Metal Oxide
R9627 VRS-TW2HF1R0JY AA J Resistor 1 1/2W Metal Oxide
RMC101 RRMCUA108WJQZY N V Remote Receiver
S101 QSW-KA037WJZZY AC J Switch
SC502 QSOCNB037WJQZ AF J Socket
SC1501 QSOCZA271WJQZY AG J Socket
SC9601 QPLGNA911WJZZY V Socket
TH3301 VHHM1103J15-1Y AB J Thermistor
TU1101 RTUNQA067WJQZ AU J Tuner
VA505 RH-VXA074WJZZY AB J AVRL101A1R1NTB
VA506 RH-VXA074WJZZY AB J AVRL101A1R1NTB
X3301 RCRSCA239WJQZY AD J Crystal
8
[4] CABINET AND MECHANICAL PARTS
Panel SP
Ass'Y
10
E 8
LW
11
LA2
E
16
LA1
LW
7 Power 12
Unit
2
PD
12
C
12 MAIN LA2
3 Unit SP 5
D 9
B 15 6 PD LA1
14
A
1-5 1-6 14
13 4
1
1-5
17
1-6
1-2 1-5 18
1-7 1-6
1-3
1-4 1-5
1-1
9

RANK MARK DELIVERY
[4] CABINET AND MECHANICAL PARTS

1 CCABBC052WJ01 N V Rear Cabinet Ass'y
1-1 Not Available - N - Rear Cabinet
1-2 JBTN-A960WJ4A N V Control Button
1-3 LANGKD438WJ4W V VESA Angle, x2
1-4 PSPAHA978WJ4Z AB J Spacer, x4 (80 X 12 X t0.5)
1-5 PSPAHB354WJ4Z V Spacer, x4 (200 X 14 X t0.5)
1-6 PSPAHC407WJ00 V Spacer, x8 (16 X 10 X t0.55)
1-7 XEBS930P08000 AA J For VESA Holder, x2
2 GCOVAE325WJ4A N V Side Cover
3 LANGKD478WJ4W N V Bottom Bracket
4 LHLDWA101WJKZ AD J AC Cord Hook
5 QACCBA051WJN2 V AC Cord (for Middle East)
5 QACCZA048WJN2 AL J AC Cord (except for Philippines/Thailand)
5 QACCZA077WJN2 V AC Cord (for Philippines)
5 QACCZA188WJN22 V AC Cord (for Thailand)
6 QCNW-M465WJQZ N V Connecting Cord (PD)
7 QCNW-M466WJQZ N V Connecting Cord (LW)
8 QCNW-M467WJQZ N V Connecting Cord (SP)
9 QCNW-M468WJQZ N V Connecting Cord (L1)
10 RSP-ZA570WJZZ N V Speaker-L
11 RSP-ZA571WJZZ N V Speaker-R
12 XBPS730P06WS0 AA J Spacer PWB, x8
13 XBPS830P06WS0 AA J Screw for CAB, x3
14 XEBS830P08000 AA J Screw, x9 (M3x8) (LC-32LE240M)
15 XEBS830P12000 AA J Screw for Bottom Bracket, x2 (LC-32LE340M)
16 TLABZD156WJZZ N V POP Label
17 TLABME206WJZZ N V Model Label (except for Thailand)
17 TLABME207WJZZ V Model Label (LC-32LE240M for Middle East)
17 TLABME208WJZZ V Model Label (LC-32LE240M for Thailand)
17 TLABME209WJZZ N V Model Label (LC-32LE340M)
18 TLABSA206WJZZ V Regulation Label (for Indonesia)
10
[5] LCD PANEL
2-5
2-5
2 2-1
2-4
1
2-5
2-5
12
LCD
Panel Unit 2-3
2-2 F
3-1 2-5
13
3
3-3
11
3-2
4-2
4-1 A 4-3
4
4-5
4-4
D
6 B C
LED 4-5
5 PWB-B
10
9
14
8 F
7 LED
PWB-A
11

RANK MARK DELIVERY
[5] LCD PANEL

1 Not Available - N - Panel Ass'y
2 CANGKD508WE01 N V Bezel Ass'y
2-1 Not Available - N - Bezel Ass'y (Top)
2-2 CANGKD509WJ01 N V Bezel Ass'y (Bottom)
2-3 CANGKD510WJ01 N V Bezel Ass'y (Left)
2-4 CANGKD511WJ01 N V Bezel Ass'y (Right)
2-5 LX-BZ2312TPZZ AB J Screw, x8
3 CCABAC850WJ02 N V CAB-A Ass'y (LC-32LE240M)
3 CCABAC850WJ01 N V CAB-A Ass'y (LC-32LE340M)
3-1 Not Available - N - CAB-A
3-2 HDECPA100WJ4A N V DECO Sheet (LC-32LE240M)
3-2 HDECPA099WJ4A N V DECO Sheet (LC-32LE340M)
3-3 HDECQB690WJ4A N V LED DEC
4 CCHSMA655WJ01 N V Chassis Ass'y
4-1 Not Available - N - PWB Chassis
4-2 LHLDWA175WJUZ AC J WH, x2
4-3 LHLDWA176WJUZ AC J WH, x2
4-4 LHLDWA181WJKZ AC J AC Cord WH, x2
4-5 PSPAZC831WJZZ N V Spacer for SPK, x2
5 PGiDMA049WJZZ N V LGP
6 PMiR-A315WJZZ N V Reflection
7 PRDARB028WJ4W N V Heat Spreader
8 PSHEPB178WJZZ N V Diffusion Sheet
9 PSHEPB179WJZZ N V Lens Sheet H
10 PSHEPB180WJZZ N V Lens Sheet V
11 PSHEPB206WJZZ N V Bottom Sheet
12 PSHEPB207WJZZ N V Lens Sheet
13 PSHEPB208WJZZ N V Right Sheet
14 XEBS830P08000 AA J Screw, x5 (M3x8)
12
X1 Remote control unit X2 Operation manual X3 "AAA" size battery (x 2)
X4 Stand base X5 Screws (x 4) X6 Antenna adaptor

RANK MARK DELIVERY

X1 RRMCGB016WJSA N V Remote Control Unit
X2 TiNS-F404WJZZ V Operation Manual (for Indonesia/Vietnam/Thailand)
X2 TiNS-F405WJZZ N V Operation Manual (for Asia)
X2 TiNS-F406WJZZ N V Operation Manual (for Asia/Middle East)
X2 TiNS-F407WJZZ V Operation Manual (for Thailand)
X2 TiNS-F408WJZZ V Operation Manual (for Vietnam)
X2 TiNS-F409WJZZ V Operation Manual (for Middle East)
X2 TiNS-F415WJZZ N V Operation Manual (for Asia/Middle East)
X2 TiNS-F416WJZZ V Operation Manual (for Indonesia)
X2 TiNS-F417WJZZ V Operation Manual (for Middle East)
X2 TiNS-F418WJZZ V Operation Manual (for Philippines)
X3 Not Available - - "AAA" Size Battery, x2
X4 CDAi-A814WJ01 N V Stand Base
X5 XBBS740P40JS0 AD J Screw for Stand, x4
X6 QCNCWA969WJZZ V Antenna Adaptor (for Philippines)
X7 TGAN-B249WJZZ V Warranty Card (LC-32LE240M for Philippines)
X7 TGAN-B383WJN1 V Warranty Card (LC-32LE240M for Vietnam)
X7 TGAN-B636WJZZ AD J Warranty Card (for Asia)
X7 TGAN-B728WJZZ V Warranty Card (for Indonesia)
13
[7] PACKING PARTS (NOT REPLACEMENT ITEM)
‫ ڎ‬S4
X1 ‫ ڎ‬S2
X4 ‫ ڎ‬S3
X2
X3
X5
X6
X7
‫ ڎ‬S6 ‫ ڎ‬S5
‫ ڎ‬S8
‫ ڎ‬S1 ‫ ڎ‬S7
‫ ڎ‬Not Replacement Item

RANK MARK DELIVERY
[7] PACKING PARTS (NOT REPLACEMENT ITEM)

S1 SPAKCG642WJZZ - N - Packing Case (except LC-32LE240M for Indonesia, LC-32LE340M)
S1 SPAKCG643WJZZ - - Packing Case (LC-32LE240M for Indonesia)
S1 SPAKCG644WJZZ - N - Packing Case (LC-32LE340M for Asia)
S1 SPAKCG645WJZZ - - Packing Case (LC-32LE340M for Indonesia)
S2 SSAKHA050WJZZ - - Pack for Screw
S3 SSAKA0001PEZZ - - Polyethylene Bag
S4 SPAKPB846WJZZ - N - Hoso PP
S5 SPAKXD570WJZZ - N - Top Pad
S6 SPAKXD571WJZZ - N - Bottom Pad
S7 TLABV0182AJZZ - - No. Card
S8 TLABZD107WJZZ - - Carton Label (for Vietnam)
14

COPYRIGHT © 2011 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Dec. 2011 CS Promotion Center
SH. DS Yaita,Tochigi 329-2193, Japan

Service Manual: LCD Colour Television

Uploaded by

Copyright:

Available Formats

Service Manual: LCD Colour Television

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: LCD Colour Television

Uploaded by

Copyright:

Available Formats

TopPage

LCD COLOUR TELEVISION

This document has been published to be used for

Downloaded from www.Manualslib.com manuals search engine

IMPORTANT SERVICE SAFETY PRECAUTION

Employing lead-free solder

Using lead-free wire solder

MAJOR SERVICE PARTS

Ref No. Part No. Description

Ref No. Part No. Description

Item Model LC-32LE240M LC-32LE340M

[1] OPERATION MANUAL

Remote control sensor

Remote control unit

Attaching the stand

2 Insert the stand base to the stand post on the

[1] REMOVING OF MAJOR PARTS

2. Remove the 1 screw , 3 screws and 8 screws .

3. Detach the Rear Cabinet Ass’y .

Rear Cabinet Ass'y 6

POWER Unit MAIN Unit

3. Remove the 3 screws and detach the POWER Unit .

4. Detach the Speaker-L/R .

2. Detach the LCD Panel Unit .

LCD Panel Unit 3

4. Detach the bottom Sheet , Left Sheet and Right Sheet .

5. Detach the LCD Panel Unit from CAB-A .

14 Bezel Ass'y (Right)

[1] ADJUSTMENT PROCEDURE

Remote controller key Main unit key Function

USB device found

5) A few seconds later, the software upgrading will start automatically.

Do not power off

Please re-boot the system

8) Plug off the LCD TV and plug ON again as usual.

4. EDID DATA INPUT

Adjustment item Adjustment conditions Adjustment procedure

4.2. ANALOG PC EDID

Adjustment item Adjustment conditions Adjustment procedure

NOTE: *1 HDMI EDID file name : edid_32LE340_HDMI1_111019.bin

Main Software Package

Model Software Package

Main Software File name : XXX is Software version

• PAL Composite signal : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)

5.1.1 ADJUSTMENT MODE

Adjustment item Adjustment conditions Adjustment procedure

5.1.2 Component 15K 50Hz signal adjustment (COMP-SD)

Adjustment item Adjustment conditions Adjustment procedure

100% white Black

5.1.3 Component 33K 60Hz signal adjustment (COMP-HD)

Adjustment item Adjustment conditions Adjustment procedure

100% white Black

Adjustment item Adjustment conditions Adjustment procedure

Adjustment item Adjustment conditions Adjustment procedure

3) Through RS-232C command, adjustment mode screen is displayed.

2 Auto Adjustment [command] [Adjustment Procedure]

FACT0001 3) Calculate min. brightness (Lmin)=Lmax/1000.

Point 2 7) Measure Point 1 brightness (Llow).

Write 11)Adjusted value is writing at [command] MSET0003.

Employing lead-free solder

Using lead-free wire solder