Operational Amplifiers: The Ideal Op-Amp in Negative Feedback
Operational Amplifiers: The Ideal Op-Amp in Negative Feedback
Operational Amplifiers: The Ideal Op-Amp in Negative Feedback
VDD
vn −
in
vo
vp +
ip
−VDD
An operational amplifier, or op-amp, is a device that outputs the difference between its two inputs, vp − vn ,
multiplied by an absurdly large number A (called the gain of the op-amp), vo = A(vp − vn ).
It has five terminals:
The positive power supply terminal is almost always connected to VDD .
The negative power supply terminal is typically connected to −VDD , a (different) negative power supply,
but in some circuits (including the ECG you’ll build in lab 4) it is connected to ground.
The inverting input is labeled − on the schematic symbol. We typically call its voltage vn .
The non-inverting input is labeled + on the schematic symbol. We typically call its voltage vp .
The fifth terminal, of course, is the output.
For brevity, it is common to draw op-amp symbols without the power supply terminals, leaving them implicit.
Confusingly, different texts and datasheets use V+ and V− to mean either the inputs or the power supply
terminals. For this reason, we’ll avoid this notation, but watch out for it in datasheets and other sources.
When an op-amp is used in negative feedback, the consequence of infinite gain is that the two inputs will be
forced to be equal. That is, the op-amp will output whatever voltage is necessary in order to make the two
inputs equal. Thus, in negative feedback, when A = ∞,
vp = vn
The above equations are, collectively, known as the golden rules of ideal op-amps in negative feedback.
1 There’s more to it than that, but the other properties only make sense when contrasted with non-ideal op-amps, which we
don’t discuss in ENGR 40M.
Output saturation
Naturally, an op-amp can only output voltages contained within the range of its power supply. (In fact,
most op-amps can’t quite hit that range—they stop at about 1 V to 2 V before the power supply voltage,
depending on the op-amp and circuit.) When the output voltage implied by the circuit would exceed the
possible range, the op-amp is said to saturate, and it just outputs its maximum or minimum possible voltage
instead.
We often call the supply voltages the rails. When op-amp output saturation causes the signal to be cut off
close to the rails, we say that the signal is clipped.
−VDD clipping
Practical matters
Is the gain really infinite? Obviously, no op-amp actually has infinite gain. But in practice, the gain of
most op-amps is high enough that, in negative feedback, vp = vn is a very reliable approximation. Moreover,
the gain of op-amps typically isn’t precisely specified—the LM4250CN, for example, merely guarantees that
it’s at least 25 000 (with no upper bound). The usefulness of an op-amp isn’t so much the high gain, as it is
that a ridiculously high gain allows us to use negative feedback to make circuits with very predictable gain.
What’s inside an op-amp? An op-amp is implemented with lots of transistors. (Recall that transistors
can be used as either amplifiers or switches, though we only studied the latter.) The precise number varies
from model to model, but as an example, the LM4250CN (which you’ll use in lab 4) has eighteen.
Examples
The following examples are all extremely common circuits.
Example 1 (Inverting amplifier). The circuit below is known as an inverting amplifier.
R2
vin −
R1 vout
+
2
R2
This means that the output is a multiple of − R 1
times its input. For example, if R2 = 4 kΩ and R1 = 1 kΩ,
then the gain would be −4. If you put a 1 V peak-to-peak (1 Vpp) sine wave into the input, the output
would look like this:
2
vout (t)
0.5 t
−0.5
vin (t)
−2
R2
−
R1 vout
vin +
Exercise 1. Consider a non-inverting amplifier with R1 = 10 kΩ and R2 = 90 kΩ. The op-amp is supplied
with VDD = 12 V to its positive power supply terminal, and −VDD = −12 V to its negative power supply
terminal, and the op-amp’s output saturates at 1.5 V from the power supplies. You provide the circuit with
an input vin (t) that looks like this:
vin (t)
2
1
t (s)
1 2 3 4
−1
3
Example 3 (Voltage follower). The circuit below is known as a voltage follower or voltage buffer.
−
vout
vin +
Find the gain of this circuit. What do you think its purpose is?
Hint: A buffer, in several engineering disciplines (and by extension, more generally in life), is something
that isolates or separates two things, to minimize the influence or impact of one on the other. Why is this
circuit called a buffer?
Exercise 2. The non-inverting amplifier in Example 2 is only capable of gains greater than 1. How would
you design a circuit whose gain is positive and less than 1, but whose output does not depend on the load
resistance?
R2
v1 −
R1 vout
v2 +
R1
R2
Remark. This sounds like it might be really useful, but notice that this circuit draws current from the inputs.
In many applications (for example, an electrocardiogram), this might affect what you’re trying to measure.