SJ-58L-C2

SJ-63L-C2
SJ-68L-C2

SERVICE MANUAL
S6011SE60APWE

REFRIGERATOR-FREEZER

MODELS SJ-58L-C2W
SJ-63L-C2W
SJ-68L-C2W
In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only
parts identical to those specified should be used.

This equipment complies with

the requirements of Directives
96/57/EC,89/336/EEC and
73/23/EEC as amended by
93/68/EEC.

DESTINATION ......................... E,I

Refrigerant; HFC-134a
Refer to "HFC-134a COOLING UNIT" Service Manual for handling this refrigerant.

TABLE OF CONTENTS

page
ENERGY LABEL .............................................................................................................................................. 2
INSTALLATION ................................................................................................................................................ 2
CAUTIONS AND INFORMATIONS .................................................................................................................. 3
SPECIFICATIONS ........................................................................................................................................... 4
DESIGNATION OF VARIOUS PARTS ............................................................................................................. 5
LIST OF ELECTRICAL PARTS ........................................................................................................................ 6
THE FICHE ...................................................................................................................................................... 7
WIRING DIAGRAM .......................................................................................................................................... 8
FUNCTIONS .................................................................................................................................................. 10
ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS ............................................................. 13
MODIFICATION PROCEDURE OF THE DOOR OPEN SIDE ....................................................................... 21
COOLING UNIT ............................................................................................................................................. 24
REPLACEMENT PARTS LIST ....................................................................................................................... 26

SHARP CORPORATION
1
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

ENERGY LABEL

Usage of "the ENERGY LABEL"

When displaying this refrigerator in the shop-window, attach the
"ENERGY LABEL" to it in the following procedure.

E
Fix the data part of
"ENERGY LABEL (DATA)" A
B
on the data part of C
D
"ENERGY LABEL (BASE)" E
F
G
"ENERGY LABEL (DATA)"
Data part
(This label is in Operation manual)

"ENERGY LABEL (BASE)" Refrigerator

of each language

INSTALLATION

Free standing type

To ensure adequate ventilation for this refrigerator, install with 6 cm space at the rear and both sides, with a
minimum space of 9 cm above the refrigerator.

9cm

6cm 6cm

This refrigerator shall be used under the ordinary place condition between +5˚C and +43˚C of ambient
temperature, and also not be left under -10˚C for long days.
To be used this refrigerator within the range of the rated voltage ±6%.

2
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

CAUTIONS AND INFORMATIONS

In case of following troubles, the cause is not related with the failure of refrigerator.
Please mention the correct way to the customer for the use of refrigerator when the repairing.

1. Some foods freezed in the refrigerator compartment.

Do not place food directly in front of

cold air outlet.
This may lead to the food freezing.

cold air flow

IN
OUT

2. Some plastic parts were cracked or splitted.

Some household cleaning chemicals may affect the internal

food liner and plastic parts resulting in splitting or cracks
occurring.
When cleaning all plastic parts inside this refrigerator, only
use diluted dishwashing liquid(soapy water). Make sure that
all plastic parts are thoroughly rinsed with water after cleaning.

3. IT IS NORMAL for the refrigerator to produce the following sounds.

Cracking or crunching sound;

Sound produced by expansion and contraction of inner walls and internal parts during cooling.
Squeaking sound;
Sound produced by expansion and contraction of internal parts.
Sound of flowing fluid (gurgling sound, fizzing sound);
Sound of refrigerant flowing in pipes (sound may become louder from time to time).

3
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

SPECIFICATIONS
Items SJ-58L-C2 SJ-63L-C2 SJ-68L-C2
Type 2-Door 2-Door 2-Door
Outer dimensions Height 1620mm(63.8") 1720mm(67.7") 1820mm(71.6")
(Including spacer) Width 760mm(29.9") 760mm(29.9") 760mm(29.9")
Depth 740mm(29.1") 740mm(29.1") 740mm(29.1")
Rated storage volume 492 liter (17.4 cu.ft) 535 liter (18.9 cu.ft) 577 liter (20.4cu.ft)
F: 151 liter (5.3 cu.ft) F: 151 liter (5.3 cu.ft) F: 151 liter (5.3 cu.ft)
R: 341 liter(12.1 cu.ft) R: 384 liter(13.6 cu.ft) R: 426 liter(15.1 cu.ft)
Rated gross volume 525 liter (18.6 cu.ft) 565 liter (20.0 cu.ft) 610 liter (21.6 cu.ft)
F: 171 liter (6.1cu.ft) F: 171 liter (6.1cu.ft) F: 171 liter (6.1cu.ft)
R: 354 liter(12.5cu.ft) R: 394 liter(13.9cu.ft) R: 439 liter(15.5cu.ft)
Defrosting System Heater system
Start Automatic
Finish Automatic
Temperature control Automatic (Adjustable)
No-frost freezer Yes
Interior lamp 2
Caster 4
Evaporating pan 1
Refrigerator R glass shelf ass'y 2 3
Compartment V glass shelf ass'y 1
Vegetable case 1
Fruit case 1
R door pocket 1 2
Egg tray 2
Bottle pocket 2
Utility case pocket 1
Chilled case 1
Tube stand 2
Freezer Freezer shelf ass'y 1
Compartment Ice cube maker Twin ice cube maker
Ice storage box 1
F door pocket 2
Deodorizing system No
RATING
Items SJ-58L-C2 SJ-63L-C2 SJ-68L-C2
Rated voltage (V~) 220-240
Rated frequency (Hz) 50
Climate class T
Rated input (W) 170-190
Rated input of heating elements (W) 138-164
Refrigerant (Charging quantity) HFC-134a(120g) HFC-134a(125g) HFC-134a(130g)
Net Weight (kg) 81 83 88
PLUG TYPE
Destination mark E I
Plug cord 3wires
Plug type CS BF
Hole

with FUSED

COLOR
Items C2W
Outside color White
Inside color White
OPTIONAL ITEM
SJ-L838LD (REFRIGERATOR HINGE KITS). For changing the door to left side opening.
4
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

DESIGNATION OF VARIOUS PARTS

The names are the denominations used in the
REPLACEMENT PARTS LIST.

1. Freezer light(Lamp)
1 2. Freezer fan
18 3. Freezer shelf(F shelf ass'y)
2 4. Ice cube maker
19 5. Ice cube box(Ice storage box)
3 6. Freezer temp. control knob
4 20 7. Chilled case
8. Refrigerator temp. control knob
5 21
9. Refrigerator fan
6
7 22 10. Refrigerator light(Lamp)
11. Refrigerator shelf(R glass shelf ass'y)
8 (SJ-58L/ SJ-63L; 2 shelves, SJ-68L; 3 shelves)
9 23
12. Shelf(V glass shelf ass'y)
10 24 13. Fruit case
11 14. Vegetable crisper(Vegetable case)
25 15. Evaporating pan & cover
12 26 16. Caster
13 17. Adjustable feet(Adjustable leg ass'y)
14 18. Fan & light switch(for freezer)
27 19. Fan & light switch(for refrigerator)
15 20. Freezer pocket(F door pocket)
16 21. Water cup
22 22. Magnetic door seal(Door packing)
17 23. Utility pocket(Utility case pocket)
24. Egg holder(Egg tray)
25. Free pocket(R door pocket)
Figure D-1. External Description
(SJ-58L/63L; 1 pocket, SJ-68L; 2 pockets)
26. Bottle pocket
27. Bottle guard(Tube stand)

Upper hinge cover Mark: Cold air flow

Hot pipe Freezer fan

Fan motor
Freezer Defrost thermostat
compartment
Evaporator
Freezer temp. control knob Defrost heater

Hot pipe

Refrigerator Timer, R-fan themo. ass’y

compartment Refrigerator fan
Damper thermostat
Refrigerator temp. control knob
Drain pipe
Fruit case

Vegetable case
Ventilating grille Compressor
Starting relay, Overload relay(Protector)
Evaporating pan
Adjustable leg ass’y Sub. condenser
Caster

This figure shows SJ-63L

Figure D-2. Constructions

5
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

LIST OF ELECTRICAL PARTS

ITEMS TYPE NAME RATING SPECIFICATIONS

Thermostat MM1-8123 125V 6A (At normal notch)
250V 3A ON/OFF : -19/-24˚C
Defrost thermostat S101 250V 8A Open/Close : 10/1˚C
Thermo. fuse SF70E 250V 10A Working temp. : 70˚C
F-fan motor 3R00044B 220-240V 50/60Hz Working with ø100 fan
R-fan motor 3R00122A 220-240V 50/60Hz Working with ø80 fan
(R-fan fuse) 123 250V 2A Cut OFF 130˚C
Defrost heater MM6-4198 220-240V 353Ω 150W at 230V
Door switch DSD-5 250V 0.25A 4 terminals push-button type
Damper thermostat MM1-6170 — Open/Close : 3/-2˚C
Defrost timer TMDF904FD2 220-240V Integration type
50/60Hz Cycle time : 10.8/9.0 hours(50/60Hz)
Delay time : 4.3/3.6 min.(50/60Hz)
Lamp socket (F/R) — 250V 1A E-12(Hard plastic body type)
F-lamp — 240V 10W E-12
R-lamp — 240V 15W E-12
R-fan thermo. R-fan thermo. S101 250V 8A Open/ Close : 7/15˚C
ass'y R-fan thermo.heater RSS2 350V, 2W, 10kΩ 1.1W at 230V

SJ-58L,63L
Compressor GLY80AA 220-240V/50Hz Cooling capacity : 197kcal/h(50Hz)
Main coil : 10.3Ω Common
Aux. coil : 14.2Ω
(at 25˚C)

Aux. coil Main coil

Starting relay UH3003-7 — 14.0 Ω + 30%

Runnig capacitor — 430VAC 5µF —
Overload relay(Protector) 4TM308NFBYY — Open/ Close : 120/61˚C

SJ-68L
Compressor GLY90AA 220-240V/50Hz Cooling capacity : 220kcal/h(50Hz)
Main coil : 8.8Ω Common
Aux. coil : 14.2Ω
(at 25˚C)

Aux. coil Main coil

Starting relay UH3003-7 — 14.0 Ω + 30%

Runnig capacitor — 430VAC 5µF
Overload relay(Protector) 4TM757NFBYY — Open/ Close : 120/61˚C

6
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

THE FICHE (according to ANNEX : 94/2/EC)

NO. Items Description Remarks

1 Trade mark
2 Model name SJ-58L-C2 SJ-63L-C2 SJ-68L-C2
3 Type Category; 7 Category; 7 Category; 7
Refrigerator/Freezer Refrigerator/Freezer Refrigerator/Freezer
4 Energy efficiency class B B B
5 Eco-award mark 880/92
6 Energy consumption 675 705 734 EN153
(220V 50Hz at 25 C) kWh/year kWh/year kWh/year
7 Net storage volume of fresh 341 L 384 L 426 L
food storage compartment
8 Net storage volume of fresh 151 L 151 L 151 L
frozen food storage compartment
9 Star rating of frozen food 4-STAR 4-STAR 4-STAR
compartment
10 No frost No frost No frost No frost
11 Temperature rise time 10 h 10 h 10 h
12 Freezing capacity 8 kg /24h 8 kg /24h 8 kg /24h
13 Climate class T T T
14 Noise 41 dB(A) 41 dB(A) 41 dB(A) 86/594/EEC
re 1 pw re 1 pw re 1 pw dB(A) re 1 pw

(96/57/EC)
15 Maximum allowable electricity 942 989 1033
consumption (Emax) kWh/year kWh/year kWh/year

7
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

WIRING DIAGRAM

Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set.

G : GRAY
Br : BROWN
O : ORANGE
Y : YELLOW
R : RED CONNECTED IN TERMINAL BOX
P : PINK
B : BLUE CONNECTOR
Bk : BLACK
S-B : SKY-BLUE
G-Y : GREEN-YELLOW
W : WHITE

F-THERMOSTAT (G)
(BR)
3 4
(R)
TM
R F DEFROST
FM FM TIMER

F R THERMO. 2 1
R-FAN THERMO. FUSE
L L HEATER

(W) (BK)

(O)
(S-B) R-FAN DEFROST
2 4 THERMO. 3 HEATER
PROTECTOR
(Y)
SOURCE CORD

DOOR SWITCH 1 COMPRESSOR

DEFROST
THERMOSTAT C
M
A
(B)
RUNNING STARTING
CAPACITOR RELAY

Figure W-1. Wiring Diagram

8
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

CABINET ASS’Y
F LAMP BOX ASS’Y
LAMP SOCKET BR-1
F-LAMP(10W) 1 1
L W-2
2 2

E. V. COVER ASS’Y
LEAD EV-COVER ASS’Y GY-1
1 1
F-FAN MOTOR FM OR-1
2 2
3 3 R-1
F-THERMOSTAT BR-2
4 4
Y-1
5 5
DEF. THERMO. ASS’Y BL-1
6 6
7 7 BK-1
FUSE ASS’Y 8 8 W-1
OR-3
9 9
(W-1)
1 1
DEF. HEATER ASS’Y Y-2
2 2
DOOR SWITCH
(OR-1)
3 (PUSH CLOSE) 3
BL-2
1 (NEUTRAL) 1
SB-1
4 (PUSH OPEN) 4
(W-2)
2 (PUSH OPEN) 2

R CONTROL COV. ASS’Y

(R-1)
3 3
(BK-1)
2 2
GY-2
4 4
(Y-1)
TM 1 1
(Y-2)
DEFROST TIMER

(R-FAN SB-2
1 1
THERMO. HEATER) BR-3
2 2
OR-3
3 3
R FAN THERMO.
4 4 OR-2

R LAMP BOX ASS’Y

BR-4
R-FAN MOTOR 1 1
FM (OR-2)
2 2
SB-3
3 3
R-LAMP (15W) L
4 4
LAMP SOCKET

TERMINAL BOX

BROWN BLUE GRAY

SKY-BLUE
RUNNING CAPACITOR EARTH

PROTECTOR
1 COMPRESSOR
L
C
E
M
N
A
SOURCE CORD STARTING
RELAY

TERMINAL COVER

Figure W-2. Electric Accessories Layout

9
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

FUNCTIONS
1. ADJUSTABLE TEMPERATURE CONTROL
(1) Temperature control of freezer
Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and
cool air circulating fan (F-fan motor) , and allows the freezer temperature to keep at a suitable temperature.
However adjust the freezer temp. control knob as follows depending upon the storing condition of foods.
MED
4 5 KNOB PURPOSE
3 6
2 SETTING
1 7
MIN MAX MAX(Coldest) For making ice rapidly or fast freezing.
Coldest
When restocking with fresh food.
MED For normal freezing.
For storing frozen food for a short period (up to one month).
FREEZER TEMP. CONTROL
Figure F-1. MIN When frozen food or ice cream is not stored.

(2) Temperature control of refrigerator

Damper-thermostat senses temperature of the refrigerator and changes the opening angle of the damper
automatically.
However, as the Damper-thermostat has no function to switch on or off the compressor and F-fan motor,
the freezer temperature control causes temperature in the refrigerator to vary to some extent.
However, adjust the refrigerator temp. control knob as follows depending upon the cooling condition.

MED KNOB PURPOSE

4
SETTING
3 5
CHILLED For keeping freshness of food longer.
ZONE
2 6 (Coldest)
CHILLED
ZONE When the refrigerator does not provide sufficient cooling.
MIN 1 7 Coldest MED For normal operation.
REFRIGERATOR TEMP. CONTROL When the refrigerator provides excessive cooling.

Figure F-2. MIN

When the temperature of the refrigerator is higher, R-fan thermo. senses the temperature and the
refrigerator is cooled efficiently by running of R-fan motor.
R-fan thermo. heater energizes when the door is opened intend to promote to running of R-fan motor.

NOTE: The refrigerator temperature is affected also by the freezer temperature. If the freezer temp.
control knob is set at the position "MAX", the temperature tends to be lower than the following
values, and if set at near the position "MIN", temperature tends to be higher.
If the refrigerator is operated for a long time with the freezer temperature control sets the "MAX"
position, foods stored in the refrigerator compartment may also freeze.
When refrigerator temperature control sets to the "CHILLED ZONE", some foods stored may
freeze.
In this case adjust control set back to the "MED" position.
When refrigerator temperature control sets to the "CHILLED ZONE", some foods stored in chilled
case may also become frozen.

(3) Reference value of temperature

SETTING OF SETTING OF CHILLED
FREEZER TEMP. MAX MED MIN REFRIGERATOR TEMP. ZONE MED MIN
CONTROL KNOB (Coldest) CONTROL KNOB (Coldest)
Freezer Approx. Approx. Approx. Refrigerator Approx. Approx. Approx.
temperature -21 C -18 C -15 C temperature 0C 3C 6C

Chilled room Approx. Approx. Approx.

temperature -3 C 1C 4C

The values shown above refer to the case where the

freezer temp. control knob is set at "MED".
The values shown above refer to the measurement carried out center area and 1/3 of overall height from the bottom
at each of the refrigerator and the freezer after machine has been operated at an ambient temperature of 30˚C with no
food stored and the door closed until the temperature is stabilized.
The values vary depending upon frequency of opening and closing the door, ambient temperature, amount of stored
foods and manner of storing foods.
10
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

2. DEFROSTING
(1) No defrosting operation is necessary (2) Where is melted frost brought
No defrosting operation is necessary. 1. Melted frost is brought into the evaporating
As this machine is so designed that a built-in pan at the bottom of the set and is evaporated
evaporator cools air and a fan circulates cooled here by the heat of sub condenser.
air, neither the freezer nor the refrigerator is 2. Be sure that the evaporating pan is inserted
frosted, though the evaporator is frosted. correctly and is level.
The frosted evaporator is defrosted automatically
due to the function of defrosting timer and heater,
requiring no defrosting operation.

(3) The following circuit diagrams in the table show automatic defrosting function of the refrigerator with
timer and defrost thermostat.

Operation Electric diagram Description

1. Cooling Defrost thermostat ON Compressor running The integration timer integrates running
(Normal) Timer motor running time of the compressor. When it reaches
Thermostat Timer contact cycle time of defrost timer, the timer
contact is changed to start defrosting.

Compressor
Timer motor
Thermo. fuse
SOURCE

Defrost heater TM COMP

Defrost
thermostat (ON)

Figure F-3.
2. Defrosting Defrost thermostat ON Compressor stops The timer contact is changed to start
(Time 20 to 30 min.) Timer motor stops defrosting, the timer motor stops, and
Thermostat Timer contact power is supplied to the defrost heater.
It takes about 20 to 30 min. to defrost.
Compressor
Timer motor

Thermo. fuse When little frosted, the defrosting takes

SOURCE

Defrost heater TM COMP little time. When much frosted, the def-
rosting takes much time.
Defrost
thermostat (ON)

Figure F-4 .
3. Drain Defrost thermostat OFF Compressor stops When the defrost thermostat becomes
(Time approx. 5 min.) Timer motor running OFF, the timer motor starts running.
Thermostat Timer contact During the operation time (delay time
of defrost time) defrosted water is
Compressor
Timer motor

Thermo. fuse drained outside the refrigerator.

SOURCE

Defrost heater TM COMP

Defrost
thermostat (OFF)

Figure F-5.
4. Restart Defrost thermostat OFF Compressor running Timer contact is changed to cooling
(Time approx. 5 min.) Timer motor stops operation and the compressor starts
Thermostat Timer contact running and the timer motor stops.
Defrost thermostat contact becomes ON
Compressor
Timer motor

Thermo. fuse when it’s cooled. And the timer motor

SOURCE

Defrost heater TM COMP starts running. (Figure F-3.)

Defrost
thermostat (OFF)

Figure F-6.

11
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

(4) As a reference to determine the causes of trouble, malfunction and phenomena are described below.
Refer to the following when repairing.
1. Disconnection of defrost heater
As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is
started, the freezer temperature rises and a portion of ice and stored foods are melted.
2. Melted thermo. fuse or opened-circuit due to the defect of defrost thermostat.
When the above mentioned trouble occurs in cooling operation, the timer motor does not run, defrosting
will not take place, and consequently freezing is caused. In the above mentioned condition, when the timer
shaft is turned by hand to defrost, the timer motor runs during the operation time. However, the motor stops
from the time when the contact is changed, and freezing causes.

NOTE:
As the thermo. fuse assembly is intended to prevent dangers, do not use it under shorted condition even
for a short period.

3. DEW PREVENTION
The hot pipe, namely D.P.-condenser, is arranged around the flange part of
cabinet and the C-partition plate, preventing dew from being generated on
the cabinet.

NOTE:
D.P.-condenser pipe may be felt hot if touched by hand while the
compressor is in operation.
If you are asked about this, please explain that the hot pipe serve to Hot pipe
prevent the dew generation.

Figure F-7
4. INSPECTION OF INITIAL STARTING
(1) Inspection of cooling unit
1. Set the temperature control knob to "MAX" and check that the compressor starts to operate.
2. Depress the door switch to run the fan and check that cool air is blown out of the cold air outlet of the
freezer and the refrigerator.
3. When the compressor does not work, check that the timer is not set to "defrost" position.
4 It takes about an hour and a half or two hours to put food in the refrigerator after starting operation.

NOTE:
After return the temperature control knob to "MED" position.
When the refrigerator is operated initially after installed, the compressor may vibrate excessively for 1 to 2
min. However, vibration becomes normal if it is continuously operated.

(2) Inspection of defrost device

Operate the refrigerator for 20 to 30 min. and then check the defrost device in the following procedures :
Allow 5 min. to restart the compressor since immediate starting after stopping will cause unsmooth operation.
1. Turn the timer shaft clockwise with a screw driver.
At this time, make certains the timer clinks and the compressor stops.
2. After more than 5 min., turn the shaft further to operate.
Make certain cooling operation is started again.

12
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS

CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING.

1. R-CONTROL COV. ASSEMBLY

Damper thermo.
RA sealer A

R air guider A

Defrost timer
RA sealer D

R fan thermo. ass’y RA sealer C

Nylon band RA sealer B

Dial sealer

Fan cover

A sealer thermo. cap.

R-C box cover

R-temp. control knob

Figure A-1

(1) Forming sensor of Damper thermo.

Less than 130 mm

Damper
thermostat
3 +1 mm
5 +1 mm

Stick thermo.
25 + 2 mm cap. sealer

NOTE
Less than 12 mm

Minimum bending radius is R5mm.

There should be no gas leak by reforming of sensor tube.

Figure A-2

After forming, fix it to the refrigerator.

13
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

(2) Sticking of sealers to R air guider A.

[Front side] [Back side]

OVERLAP 15mm
RA sealer A OVERLAP 15mm

Dial sealer

RA sealer D
A sealer
RA sealer A RA sealer A thermo. cap. RA sealer B RA sealer C RA sealer A

[Bottom side]

A sealer
thermo. cap.

RA sealer A RA sealer A

Figure A-3

(3) Fixing of Defrost timer, R fan thermo. ass'y cover to R-C box cover.

R fan thermo ass’y

R-C box cover Nylon band

Defrost timer

Cut
10 + 5mm

G R fan thermo.
ass’y
Nylon band

Fan cover
SEC. G-G

Figure A-4

14
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

2. R LAMP BOX ASSEMBLY

R fan motor holder B

R-fan motor
Propeller fan 80

R fan motor holder A

Lamp socket (with lead wires for R-fan motor)

Fan clamp
Lamp 15W

Warning label

R lamp box

Figure A-5

(1) Fixing of Lamp and Lamp socket.

(1)-1 Screw Lamp 15W into Lamp socket.

(1)-2 Fix Lamp socket on R lamp box by tapping
screws.
Tapping screw

Lamp socket
ALUMINUM TAPE
Lamp 15W

R lamp box

Figure A-6

(1)-3 Insert the terminal of Lamp socket to R-fan motor.

DOUBLE CLAMPING WIRES

Lamp socket

Fan motor

Figure A-7

15
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

(2) Fixing of R-fan motor and Fan

R fan motor holder B
(2)-1 Set R-fan motor holder A to R lamp box by R fan motor holder A
tapping screw.
Propeller fan 80 R-fan motor
(2)-2 Set R-fan motor to R fan motor holder A by
machine screw.
(2)-3 Set R fan motor holder B to A.

Figure A-8

(2)-4 Set Fan clamp to Propeller fan 80 and insert it

to the shaft of R-fan motor.

F
Fan clamp

Propeller fan 80

2.3 + 0.5mm

Shaft

Detail of F

Fan clamp
Slit of each Fan clamp and Propeller fan
should not be at same position.
Slit

Figure A-9

(3) Sticking Warning label.

Warning label

Lamp 15W

Figure A-10

16
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

3. E.V COVER ASSEMBLY

Motor Fan motor
U-sealer cushion
handle

Propeller Fan 100

E.V cover sealer A Fan motor
holder B
Defrost thermo. ass’y Fan clamp

E.V cover L-band C Lead E.V-cover

Fan motor ass’y
holder A

E.V cover sealer B

E.V cover sealer C

Fuse ass’y

F-thermostat

E.V cover
sealer D
(2 pieces)

Figure A-11

(1) Sticking of Sealers to E.V cover

E.V cover sealer B E.V cover sealer A

E.V cover
Overlap 10mm(min)
Sticking start (a)

Sticking start

Sticking start

Sticking start (b)

E.V cover sealer D (b) E.V cover sealer D (a)

[Front side] [Back side]

Figure A-12

17
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

(2) Fixing of Fan motor and Fan

(2)-1 Stick U-sealer handle to Fan motor holder A. Fan motor holder A
C

7 + 2mm
0 + 1mm

U-sealer handle

C
U-sealer handle
SEC. C-C

Figure A-13

(2)-2 Insert the terminals of Lead EV-cover ass'y to

R-fan motor. Fan motor
(2)-3 Fix two Motor cushions to R-fan motor, and set it holder B
at Fan motor holder A and B.
Then fix with Tapping screw.
Motor cushion
Fan motor
holder A Tapping
screw

Fan motor

Lead EV-cover ass’y RED

BROWN

Figure A-14

(2)-4 Set Fan clamp to Propeller fan 100 and insert

it to the shaft of Fan motor.
Fan clamp
D
Fan clamp
Slit

Propeller Slit of each Fan clamp

fan 100 and Propeller fan
should not be at same position.

4 + 0.5mm

Shaft

Detail of D

Figure A-15

18
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

(3) Setting of Fan motor ass'y , Defrost thermo. ass'y and Fuse ass'y

E.V cover Tapping screw

E.V cover
sealer C
L-band C
E
Lead E.V-
cover ass’y Defrost
thermo. ass’y
Tapping E
more than more than Aluminum
3.5mm 3.5mm screw
tape Set metal side below
[FRONT SIDE] Aluminum
tape

Take out lead wire from F

square hole to front, and
seal with E.V cover sealer C.
F
Fuse ass’y
Defrost cut
thermo. ass’y

10 + 5mm
E.V
cover ATTENTION
L-band C
Fuse
ass’y Turn up is lead wire Not come out of claw

Sec. F-F Sec. E-E

Figure A-16

(4) Inserting of pins

Fan motor 1 , 2
F-thermostat 3
WIRE COLOR FOR FAN MOTOR (RED, inserted)
100-110V : WHITE
127V : YELLOW
220-240V : BLUE

F-thermostat 4
1 2 3
(BROWN, inserted)
4 5 6 Fan motor 9
Defrost thermo. 5 7 8 9

(PINK) Fuse 8
(WHITE)
Defrost thermo. 6
(BLUE) Fuse 7
(BLACK)

Note Pins should be inserted surely,

and check by pulling it.

Figure A-17

After inserting, fix with vinyl tape.

Vinyl tape

60
mm

Figure A-18

19
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

(5) Setting of F-thermostat

(5)-1 Form capillary tube of F-thermostat.

20mm
R10mm R10mm

230mm
Note
• Bending radius of
capillary tube should be
from R5mm to R10mm.
13mm 42mm

20mm

Figure A-19

(5)-2 Insert terminal of Lead EV-cover ass'y.

RED
(front side)

BROWN
(back side)

Figure A-20

(5)-3 Set to E.V cover.

F

SEC. F-F
F

Figure A-21

20
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

MODIFICATION PROCEDURE OF THE DOOR OPEN SIDE

It is possible to change the door to left side opening.
To modify the door to left side opening, REFRIGERATOR HINGE KITS (for left side opening) SJ-L838LD (optional item )is necessary.

These kits are used to change the refrigerator doors from right to left opening.
if you wish to change the door to left opening for some reason, such as restricted installation
space, ask your authorized service agent for this modification. by SJ-L838LD OPERATION MANUAL

Parts list Select the same color as the refrigerator exterior.

Stopper spring L Stopper spring L Door cap cover Door cap cover
A Bottom hinge L B C D E
(for upper door) (for lower door) (for upper door) (for lower door)

F Door hole cover G Screw and Cover H Silicon grease J Screw cap for handle
(Spare)

Tools required
Phillips and slotted screwdrivers
Drill bit ( 3.8 mm)
Socket wrench or spanner (8 mm) :The socket wrench or spanner is used to detach and attach hinges.

Caution
Always disconnect the power plug from the wall outlet before performing work.
Caution should be taken when handling the doors.
These are heavy and could cause personal injury if mishandled.
Always tighten screws securely. May cause personal injury if door becomes unlatched and falls.
Reattach doors paying careful attention to the door alignment. Failure to fit the door
correctly might cause the cool air to leak out and lower the cooling performance.
Fitting Instruction
1 Preparation/Removing Doors
1. Remove Evaporating pan cover, Upper hinge cover, and Top cover.
(Carefully remove Upper hinge cover using a screwdriver, making sure that the door is not damaged.)
2. Remove Upper hinge and Spacer, and detach Upper door by lifting off the center hinge.
3. Remove Center hinge and detach Lower door by lifting off the bottom hinge. Remove the 2 Hole caps, replace them on
the screw holes of the removed center hinge, then screw in G (screw and cover) in the center hole.
4. Remove Bottom hinge. Remove the 3 screws on the left side, then install them in the screw holes of Bottom hinge.

1
1
2

1 G
3 2

G 3

3
3

4 1
Figure M-1

21
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

2 Replacing Handles and Door Parts

1. Remove Screw caps and Screws on each door handle, then remove the handles.
Flatten the surface of the screw holes using the handle of a screwdriver, etc., then mount 3 units of F (Door hole covers)
on each door.
2. Remove the Nylon bearings, Door stopper(Lower door only), Stopper springs on the right side of each door and the cap
on the left side of the Upper door. Furthermore, open the hidden holes on the bottom of the door using a screwdriver,
then remove a screw (Lower door only).
3. Remove Screw caps and Screws on the right side of each door, then remove the Door cap covers and mount D and E
(Door cap covers) on the left side.
4. Replace Nylon bearings to the left side of each door, then mount the Upper door cap on the right side. Furthermore,
mount Door stopper and B and C(Stopper springs) on the left side as well. Screw in a screw in the screw hole on the
lower right of the Lower door.
5. Fix upper portion of Upper handle using one screw on the right side of Lower door, then temporarily fix the handle to the
door using tape.
6. To open screw holes, first make marks on the doorplate surface through the 3 holes of the handle, then temporarily
remove the handle (make sure that the dimensions of the markings are as shown in the diagram).
7. Lightly dent the center of each marking, then open holes using a 3.8 mm drill bit.
Use a drill guide, etc., to prevent the drill bit from entering more than 5 mm.
Make sure to open the hole straight. Opening the hole in an angle will cause the handle to clatter.
The door will be unusable if the hole are too large or too deep or if the screws are tightened too much.
8. Mount the handle using the 4 screws and install Screw caps.
9. Mount Lower handle on the right side of Upper door by repeating steps 5. ~ 8. above.

2 4
2 5,6
16mm
F
1 2
27mm

172mm
3

D 2 172mm
1 3
4 B 7
2
4 3
E
3 5mm

1 1 8
(J) 5-8
2
F
2 4 9
2
4 C

Figure M-2

22
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

3 Mounting the Door/Finishing

1. Apply Silicon grease H to the shaded portion of part A(Bottom hinge L) and attach it to the left side.
2. Insert Lower door and fit Center hinge vertically inverted. Remove washer if installed. Tighten the screws temporarily.
3. Fit Upper door and attach Upper hinge together with spacer. Tighten the screws temporarily.
4. Adjust the alignment of the door. Ensure that the gap between the cabinet and door is 12 mm. Tighten the upper hinge
screws.
5. Secure Upper door. Open Lower door and tighten the center hinge screws. (No drawing)
6. Check the following. To readjust the door position, loosen Center and Bottom hinges.
Whether the distance to activate the door switch is correct.
Whether each door can be opened/closed smoothly.
Whether each door is properly sealed when closed. (Check by inserting a sheet of paper between the door and
cabinet when closing. The refrigerator is not properly sealed if the paper falls.)
7. Apply Silicon grease H to the shaded portion of the door packing.
8. Replace the cap in Evaporating pan cover on the right side.
9. Reattach Evaporating pan cover, Upper hinge cover and Top cover.
10. Make sure that each door can be opened and closed normally. (If any of the doors cannot open/closes normally, tilt the
refrigerator slightly backward by screwing out the two adjustable feet.) Furthermore, connect the power plug, make sure
that cold air is not leaking from the door packing, and that the cabinet lamp operates properly when the door is
opened/closed.
Retain removed parts in case doors are to be changed back to right opening.

3
4 9
9
3
3
12mm

6 3.5 + 0.5mm

2 2
2 +1.0mm

2 7

A
1 8

Figure M-3

23
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

COOLING UNIT

Mark: Refrigerant flow

Mark: Brazing portion

Hot pipe L Hot pipe Hot pipe R

(Side condenser) (DP-condenser) (Side condenser)

Evaporator

Back condenser
Suction pipe

Sub. condenser

Compressor

Capillary tube
Dryer

Figure C-1. Cooling unit

24
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

Dryer
Capillary tube

Charge pipe

Hot pipe

Evaporator

Charge pipe

Compressor
Suction pipe S.P. connector
Sub. condenser Back condenser

Figure C-2. Location

Suction pipe to Sub. condenser to

S.P connector Back condenser
Back condenser to Charge pipe L to
hot pipe Compressor’s process tube Pinch Point

Compressor butyl Pinch point

Charge pipe L
to Dryer

Hot pipe
to Dryer

Suction pipe to Compressor’s discharge pipe Dryer

Compressor’s suction pipe to Sub. condenser to Capillary tube

Figure C-3. Location

25
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

REPLACEMENT PARTS LIST (SJ-58L/63L/68L-C2W)

REF. NO. PART NO. DESCRIPTION Q'TY CODE
SJ-58L SJ-63L SJ-68L
-C2W -C2W -C2W

ELECTRIC PARTS
1-1 RTHM-A097CBEZ F-thermostat 1 1 1 AX
1-2 RSTT-A144CBEZ Starting relay 1 1 1 AW
1-3 QSWTDA035CBE0 Defrost timer 1 1 1 BB
1-4 PDMP-A046CBEZ Damper thermo 1 1 1 AX
1-5 FTHM-A028CBKZ Defrost thermo. assembly 1 1 1 AN
1-6 RMOTRA040CBE0 Fan motor 1 1 1 AZ
1-7 QSOCAA074CBEZ Lamp socket 1 1 1 AP
1-8 RLMP-A012CBE0 Lamp 1 1 1 AH
1-9 QACC-A097CBE0 Source cord 1 1 1 AV
1-9 QACC-A104CBE0 Source cord (for U.K.) 1 1 1 AZ
1-10 QSW-PA090CBZA Door switch 1 1 1 AS
1-11 RHOG-A084CBE0 Protector 1 1 - AN
1-11 RHOG-A105CBE0 Protector - - 1 AV
1-17 FFS-TA055CBKZ Fuse assembly 1 1 1 AL
1-20 FW-VZA144CBEZ Lead ev-cover assembly 1 1 1 AK
1-21 FHETBA146CBEZ Def. Heater assembly 1 1 1 AZ
1-22 FCNW-A517CBK0 Relay cord s assembly 1 1 1 AM
1-23 QCNW-A671CBE0 Relay wire RC 1 1 1 AD
1-25 QTAN-A032CBE0 Terminal block 1 1 1 AE
1-27 RMOTRA061CBEZ Fan motor 1 1 1 AW
1-28 RLMP-A029CBEZ Lamp15W 1 1 1 AH
1-29 QSOCAA072CBEZ Lamp socket 1 1 1 AN
1-30 FTHM-A029CBKZ R fan thermo assembly 1 1 1 AQ
1-31 RC-EZA190CBEZ Running capacitor 1 1 1 AW
MECHANICAL PARTS
2-2 JKNB-A036CBFB F-temp. control knob 1 1 1 AD
2-4 LPLTMA568CBEZ Fl plate AL. 1 1 1 AF
2-7 FLEGPA077CBKZ Leg holder L assembly 1 1 1 AQ
2-7-1 FAJS-A009CBK0 Adjustable leg assembly 2 2 2 AD
2-7-2 LHLD-A533CBPZ Leg holder L 1 1 1 AL
2-8 FLEGPA078CBKZ Leg holder R assembly 1 1 1 AQ
2-8-2 LHLD-A534CBPZ Leg holder R 1 1 1 AP
2-10 PSPAVA083CBEA Upper hinge spacer 1 1 1 AD
2-11 PSPAVA084CBEA Bottom hinge spacer 1 1 1 AC
2-12 PSPAVA075CBEA Center hinge spacer 1 1 1 AD
2-13 DHNG-A363CBMZ Upper hinge assembly 1 1 1 AE
2-14 DHNG-A365CBMZ Bottom hinge R assembly 1 1 1 AE
2-15 DHNG-A364CBMZ Center hinge R assembly 1 1 1 AF
2-16 GCOV-A191CBFZ E.v cover 1 1 1 AS
2-17 LCRA-A010CBE0 Fan clamp 2 2 2 AD
2-19 LHLD-A389CBF0 Motor cushion 2 2 2 AF
2-20 NFANPA020CBFA Propeller fan 100 1 1 1 AE
2-21 PSEL-B845CBEZ E.v cover sealer A 1 1 1 AC
2-22 PSEL-B846CBEZ E.v cover sealer B 1 1 1 AC
2-23 PSEL-A415CBE0 E.v cover sealer C 1 1 1 AC
2-24 PCOVPA164CBFA Terminal cover 1 1 1 AE
2-25 PCOV-A253CBFA F lamp cover 1 1 1 AC
2-26 PCOV-A254CBFA R lamp cover 1 1 1 AF
2-27 GCOVPA119CBRA R-c box cover 1 1 1 AS
2-28 HGRL-A184CBRA Fan louver 1 1 1 AU
2-29 GCOV-A162CBFJ Upper hinge cover 1 1 1 AD
2-30 PCOV-A255CBFA Fan cover 2 2 2 AD
2-31 JKNB-A033CBFB R-temp. control knob 1 1 1 AD
2-36 PCAP-A006CBFW Screw cover 2 2 2 AB
2-37 PCAP-A056CBFF Screw cover B 2 2 2 AC
2-38 PGID-A156CBFZ R air guider A 1 1 1 AG
2-41 PSEL-B848CBEZ A-sealer thermo. cap 1 1 1 AC
2-49 LSTPPA108CBFA Chilled stopper 2 2 2 AC
2-50 NFANPA019CBFA Propeller fan 80 1 1 1 AM
2-51 PBOX-A121CBFA F lamp box 1 1 1 AF
2-52 PBOX-A122CBFA R lamp box 1 1 1 AM
2-53 LHLD-A536CBFA R fan motor holder A 1 1 1 AF
2-54 LHLD-A537CBFA R fan motor holder B 1 1 1 AE
2-55 HGRL-A181CBFA Multi louver L - - 1 AN
2-55 HGRL-A186CBFA Multi louver M - 1 - AM
2-55 HGRL-A188CBFA Multi louver S 1 - - AG
2-56 PFPFPB233CBFZ R-louver insu. L - - 1 AG
2-56 PFPFPB239CBFZ R-louver insu. M - 1 - AF
2-56 PFPFPB248CBFZ R-louver insu. s 1 - - AE
2-57 PSEL-B843CBEZ A-sealer r-louver - - 2 AC
2-57 PSEL-B857CBEZ A-sealer r-louver - 2 - AC
2-57 PSEL-B861CBEZ A-sealer r-louver 2 - - AC

26
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-58L SJ-63L SJ-68L
-C2W -C2W -C2W
2-59 PCOV-A264CBEZ F lamp box cover 1 1 1 AC
2-63 LHLD-A484CBFA Fan motor holder B 1 1 1 AH
2-64 LHLD-A485CBFA Fan motor holder A 1 1 1 AH
2-65 PSEL-B209CBE0 U-sealer handle 2 2 2 AB
2-66 PSHEMA132CBP0 Heater cover AL 1 1 1 AD
2-67 LPLTMA570CBPZ Drain support AL 1 1 1 AE
2-69 PSEL-B847CBEZ E.v cover sealer D 2 2 2 AC
2-71 PSEL-A552CBE0 Dial sealer 1 1 1 AC
2-72 PSEL-B841CBEZ Ra sealer A 2 2 2 AC
2-73 PSEL-B842CBEZ Ra sealer B 1 1 1 AC
2-74 PSEL-B122CBE0 A-sealer thermo. cap. 1 1 1 AB
2-77 LHLD-A391CBE0 Sl-5n clip 1 1 1 AD
2-78 LPLTMA399CBP0 Dryer support 1 1 1 AD
2-79 LBND-A019CBE0 Nylon band 1 1 1 AB
2-80 PBOX-A071CBFA Terminal box 1 1 1 AE
2-81 PPIPPA097CBEZ Drain pipe S 1 1 1 AE
2-82 PTUBBA058CBE0 Insulating tube 1 1 1 AE
2-83 PSEL-B849CBEZ Ra sealer C 1 1 1 AC
2-84 PSEL-B850CBEZ Ra sealer D 1 1 1 AC
2-86 LBND-A026CBE0 Nylon band 1 1 1 AD
2-90 HGRL-A179CBFA F shower duct 1 1 1 AM
2-91 HGRL-A180CBFA F return cover 2 2 2 AC
2-93 PCAP-A068CBFA C sliding cap A 2 2 2 AC
2-95 NROL-A027CBEZ V roller 2 2 2 AC
2-96 LHLD-A535CBFA Shaft holder 2 2 2 AC
2-97 LPIN-A178CB1Z Shaft 2 2 2 AC
2-99 GCOV-A192CBFE Top cover 1 1 1 AC
2-103 PSEL-B894CBEZ F-shower ins.A 1 1 1 AF
2-104 PSEL-B895CBEZ F-shower ins.B 1 1 1 AE
2-105 PSEL-B896CBEZ A-sealer FS-A 1 1 1 AC
2-106 PSEL-B897CBEZ A-sealer FS-B 2 2 2 AC
DOOR PARTS
3-5 FDORFB308CBKZ F-door assembly 1 1 1 BK
3-5-1 LSTPPA107CBFA Fd stopper spring R 1 1 1 AD
3-5-2 NBRGPA022CBFA Nylon bearing 3S 2 2 2 AC
3-5-3 PCOV-A251CBFE Dc cover FR 1 1 1 AC
3-6 FPACGA309CBKZ F-door packing 1 1 1 AX
3-7 HDECQA384CBFB Handle trim FL 1 1 1 AD
3-8 JHNDPA117CBFE Door handle FL 1 1 1 AN
3-9 PCAP-A067CBFE Screw cover HD 10 10 10 AD
3-15 FDORRB170CBKZ R-door assembly - - 1 BQ
3-15 FDORRB177CBKZ R-door assembly - 1 - BP
3-15 FDORRB185CBKZ R-door assembly 1 - - BQ
3-15-1 LSTP-A058CBM0 R-door stopper R 1 1 1 AF
3-15-2 LSTPPA084CBFA Rd-stopper spring R 1 1 1 AD
3-15-3 PCOV-A252CBFE Dc cover RR 1 1 1 AC
3-17 FPACGA310CBKZ R-door packing - - 1 AY
3-17 FPACGA314CBKZ R-door packing - 1 - AY
3-17 FPACGA315CBKZ R-door packing 1 - - AY
3-18 HDECQA385CBFB Handle trim RL 1 1 1 AG
3-19 JHNDPA118CBFE Door handle RL 1 1 1 AN
3-25 FBDGDA280CBYZ Badge assembly 1 1 1 AY
OTHER PARTS
4-1 LBND-A023CBE0 L-band C 4 4 4 AC
4-3 LX-VZA003CBE0 Special screw 2 2 2 AB
4-10 QTAN-A013CBE0 Solderless term. A 4 4 4 AH
4-15 LX-BZA018JBE0 Special screw 1 1 1 AA
4-17 LX-WZA003CBE0 Washer 4 4 4 AA
4-18 LX-BZA076CBEZ Handle screw 10 10 10 AC
ATTACHMENT PARTS
5-1 UPOK-A166CBRA Bottle pocket 2 2 2 AN
5-3 UPOK-A168CBRA F door pocket 2 2 2 AP
5-4 UPOK-A165CBRA R door pocket 1 1 2 AN
5-5 UTNA-A282CBFB Egg tray 2 2 2 AG
5-6 FSRA-A193CBYZ Ice cube maker 1 1 1 AS
5-9 FSRA-A194CBKZ F shelf assembly 1 1 1 AY
5-13 HGRL-A178CBFE V entilating grille 1 1 1 AN
5-14 USRA-A252CBFA Drain pan 1 1 1 AN
5-15 UYOK-A330CBFA Fruit case 1 1 1 AW
5-16 UYOK-A331CBFA Vegetable case 1 1 1 AZ
5-17 UYOK-A328CBFA Ice storage box 1 1 1 AF
5-18 UYOK-A329CBFA Chilled case 1 1 1 AX

27
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

REF. NO. PART NO. DESCRIPTION Q'TY CODE

SJ-58L SJ-63L SJ-68L
-C2W -C2W -C2W
5-19 GDORPA066CBRA Chilled door 1 1 1 AP
5-24 FTNA-A301CBKZ R glass shelf assembly 2 2 3 BC
5-25 FTNA-A302CBKZ V glass shelf assembly 1 1 1 BC
5-26 PCAP-A076CBFE Venti. Grille cap 1 1 1 AD
5-28 PCAP-A069CBFA V sliding cap L 1 1 1 AC
5-29 PCAP-A070CBFA V sliding cap R 1 1 1 AC
5-31 LRALPA132CBFA Ice tray holder L 1 1 1 AF
5-32 LRALPA133CBFA Ice tray holder R 1 1 1 AF
5-33 LRALPA134CBFA Ice tray holder B 1 1 1 AF
5-34 PCUP-A009CBFA Water cup 1 1 1 AD
5-35 UPOKPA251CBFA Tube stand 2 2 2 AC
5-36 PCOV-A259CBFA Case cover 1 1 1 AH
5-37 UPOK-A167CBRA Utility case pocket 1 1 1 AM
CYCLE PARTS
6-1 PCMPLA196CBEZ Compressor 1 1 - BX
6-1 PCMPLA202CBEZ Compressor - - 1 BX
6-2 PSPAGA028CBE0 Rubber grommet 4 4 4 AD
6-3 FCONSA077CBKZ Sub. Condenser assembly 1 1 1 AX
6-3-1 PCOV-A256CBFA Pipe protector L 1 1 1 AF
6-3-2 PCOV-A257CBFA Pipe protector R 1 1 1 AF
6-4 FFRM-A113CBKZ Base frame assembly 1 1 1 AW
6-5 FDRY-A006CBK0 Dryer assembly 1 1 1 AX
6-6 PCLI-A035CBE0 Clip 1 1 1 AC
6-9 PSPAFA020CBE0 Sleeve 4 4 4 AB
6-11 PPIPCA357CBEZ S.p connector 1 1 1 AD
6-15 PGUM-A002CBF0 Absorbent rubber B 1 1 1 AH
6-18 PPIPCA252CBE0 Charge pipe 2 2 2 AD
6-21 PCOVPA165CBE0 Terminal cover 1 1 1 AF
6-27 PSEL-B899CBEZ S-sealer 2 2 2 AC
6-28 PKYU-A143CBEZ S-butyl 1 1 1 AD
6-29 PKYU-A036CBE0 S-butyl D-poy 1 1 1 AP
6-30 PKYU-A098CBE0 Compressor butyl 1 1 1 AG
MISCELLANEOUS
90-1 TINS-A473CBRZ Operation manual 1 1 1 AF
90-2 TLAB-A092CBR0 Lamp label 1 1 1 AD
90-3 SPAKCI777YDEZ Packing case 63L - 1 - BC
90-3 SPAKCI775YDEZ Packing case 68L - - 1 BC
90-3 SPAKCI800YDEZ Packing case 58L 1 - - BB
90-5 TLAB-A900CBEZ Case label C2W 4 4 4 AC
90-6 CPADBA765YDKZ Bottom pad assembly 1 1 1 AY
90-7 CPADBA764YDKZ Top pad assembly 1 1 1 AR
90-8 TLAB-A876CBRZ Warning label 1 1 1 AC
90-11 TINS-A343CBR0 Operation manual I (for U.K.) 1 1 1 AG
90-12 TLAB-A885CBRZ Energy label - - 1 AE
90-12 TLAB-A895CBRZ Energy label - 1 - AE
90-12 TLAB-A896CBRZ Energy label 1 - - AE
90-13 TLAB-A637CBR0 Energy label(GB) 1 1 1 AG
90-13 TLAB-A638CBR0 Energy label(D) 1 1 1 AG
90-13 TLAB-A639CBR0 Energy label(F) 1 1 1 AG
90-13 TLAB-A640CBR0 Energy label(E) 1 1 1 AG
90-13 TLAB-A641CBR0 Energy label(I) 1 1 1 AG
90-13 TLAB-A642CBR0 Energy label(GR) 1 1 1 AG
90-13 TLAB-A643CBR0 Energy label(P) 1 1 1 AG
90-13 TLAB-A644CBR0 Energy label(NL) 1 1 1 AG

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the following information.

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

28
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2
1 2 3 4 5 6

DOOR PARTS
A A

3-9
3-6

3-5 3-5-2
3-8

B 3-9 B
4-18

3-9 4-18

3-9
4-18

C 4-18 C

3-25 5-34
3-7
5-3

3-5-3
3-15 3-9
4-18 3-5-1
3-9
4-18 3-5-2
D D
5-36
3-9 3-15-3
4-18 3-9

4-18

3-9
4-18

5-37

3-9
4-18
E 5-5 E
3-19
5-4
3-18

F F

5-35
5-1

3-17

G G
3-15-1

3-15-2

SJ-58L-C2
H SJ-63L-C2 H

SJ-68L-C2

1 2 3 4 5 6
29
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2
1 2 3 4 5 6

CABINET PARTS
A A

5-9 2-29

2-99 2-13

B B
2-106
5-31
2-105 2-10
5-33
5-6
2-36
2-104
2-91
5-17
2-103
5-32
C 2-90 C
2-93
5-18 1-10
2-37
2-49
2-36
2-49
4-3 2-15 2-12
2-97

2-95
2-96 2-95
2-93
D 5-19 2-96 D

2-11
5-26 5-14

2-8
2-14
5-24

E E
2-7 2-7-2 2-8-2
2-7-1 2-7-1
5-13
5-25

5-15
F 5-28 F

5-16

5-29

G G

SJ-58L-C2
H SJ-63L-C2 H

SJ-68L-C2

1 2 3 4 5 6
30
 SJ-58L-C2
SJ-63L-C2
SJ-68L-C2
1 2 3 4 5 6

CABINET PARTS
A A

2-19
1-6
2-63
2-64 2-19
2-21
2-17

2-16 1-5
4-1 2-65
2-20 1-20
2-4
B B
2-23 2-22

1-17

1-1
2-28
2-59
1-29
2-30 2-69
2-81

C C
1-8
2-51 1-31
2-25 90-2
2-66
1-21
1-23
2-2 1-4 4-10
2-72
2-67 2-24
2-79
D 2-78 D
2-41
6-18
1-3
2-84 2-83 6-5
2-82
1-30
2-79 2-73
2-71
2-77
2-38 2-80
2-30 2-79
2-27 2-74 1-27
2-53 1-9
E E
2-50
2-54 6-29
2-31
2-17 1-7 6-28
1-28
1-22
6-30
90-8 2-52

6-11
4-17 4-1

F 6-1 F
6-18 1-11
2-86
6-15
2-57 6-9
6-2 1-25

2-56 4-15
2-26 6-21
2-55 6-27 6-6
1-2

G G
6-4
6-3-1
6-3

6-3-2

SJ-58L-C2
H SJ-63L-C2 H

SJ-68L-C2

1 2 3 4 5 6
31
SJ-58L-C2
SJ-63L-C2
SJ-68L-C2

52APWE/ 52APWI/ 56APWE/ 56APWI/ 60APWE/ 60APWI 2000 (06U0.12E) Printed in Japan
32