OSC 77FD100HB Hydraulics Bench

<Features>
-This is a basic unit which provide water supply and volumetric
measurement services for use in conjuction with accessories for
specific experiments
-The bench top is molded into a measuring tank and a channel
-Water is admitted at one end of the channel via a quick coupling
for connection to an accessory which is mounted acorss and
discharges water into the channel
-The open channel discharges water into the measuring tank
which inturn discharges water to ma main storage tank and can
be drained by a bottom valve
-Both bench top and storage tanks are made of fiber glass
-The measuring tank is stepped to enable accurate measurement
of both high and low flow rates
-A level gauge at the side of the bench is provided for
measurmentof volume in the measuring tank Photograph includes optional equipment
-A bull's eye level is provided to indicate the bench level

<Specifications>
Model OSC 77FD 100HB
0.37kW centrifugal pump with a maximum flow rate over 80Lpm
Pump
and a maximum head over 18m water
Bench top dimension 1360mm long x 770mm wide
Open channel 750mm long x 250mm wide x 170mm deep
Measuring tank Low flow 101, High flow 451
Main storage tank 165L
Power supply 　　　220V, 1Ph, 50Hz. Other power supply is available on request
Size 　　　Approx. 780 x 1360 x 1050mm
Weight 　　　Approx. 111ｋｇ

<Optional Accessories>
001HB Bench leveling screws
Two side leve gauges are provided instead of one. The second level gauge measures level in
002HB
the channel. Thus flow over a notch experiment can be run without using hook and point gauge.
003HB Variable speed pump with a control panel instead of fixed speed pump
005HB Measuring tank stilling baffle
006HB Full length storage tank with capacity 250L instead of short storage tank
007HB 0.37ｋW submergible pump with flow rate over 150Lpm instead of contrifugal pump
011HF Variable area flow meter, upto 75Lpm to facilitate the experiments
011-120HF Variable area flow meter, 20-150Lpm
Pump motor if replaced by 0.55kW motor dynamometer with an inverter, a digital speed
001HP
indicator and a spring balance for measurement of pump input, and pressure gauges for
*Larger pump and other accessories can be supplied on request.
OSC 77FD100HB Optional Accessories

<Features>
-The tester is designed to calibrate pressure gauge
-It consist of a precision machined stainless steel piston and cylinder
lining using calibrated weights applied on the upper end of the
piston rod
-The assembly is mounted on adjusting screws with a bull's eye level
-The pressure gauge is connected to the cylinder, thus+ subject to known
pressure and comparison with the gauge reading can be made
-Leaking liquid from the cylinder is returned to a reservoir
-The cylinder can be refilled without removing the piston

011HB Dead Weight Pressure Tester

<Speficications>
Model OSC 77FD 011HB
Pressure gauge Bourdon tube, 0～3kg/cm2
Piston cross-section 250mm2
Piston weight 0.5kg
Calibration weight 1 x 0.5kg, 2 x 1.0, 2kg x 2.0kg
Size (WxLxH) Approx. 200（W)ｘ390（L)x300（H)mm
Weight 　Approx. 18kg

Optional HB011-002 Additional calibration pressure gauge Cl.1 with connection.

Pressure gauge reading in kN/cm2 and weights in N.

<Features>
-This equipment allows the mament caused by a fluid thrust on a
wholly or partially submerged plane surface to be measured directly
-A PVC quadrand is mounted on a balance arm pivoted on knife
edges which coincide with the quaderant cernter
-When the quadrant immerses in water, there are hydrostatic forces
-The balance arm has an adjustable counter balance and weights with
a hanger
-The quadrant is mounted on top of a clear acrylic tank which allows
water to be admitted and drained to a required level by a valve
-The tank rests on adjustable footings and a bull's eye level is provided 012HB Hydrostatic Pressure

<Speficications>
Model OSC 77FD 012HB
Quadrant Inner radius : 100mm　Outer radius : 200mm Width : 75mm
Depth scale 1mm graduation
Suspended mass to fulcrum 280mm or as required
Tank capacity 　6L
Weights 10g x 2, 20g x 2, 50g x 2, 100g x 2, 200g x 2 or weights in N
Size (WxLxH) Approx. 360ｘ460ｘ350mm
Weight Approx. 19kg
OSC 77FD100HB Optional Accessories

<Features>
-The apparatus is for the study of flow over a notched weir
-Three weir plates, a rectungular notch and two vee notches, are provided
-Characteristics of flow over the notches can be observed and coefficients of
discharge can be determined
-The plates are attached to the open channnel of the Hydraulics Bench
-Water is supplied to the channel via a discharge starainer and passes through a
stilling baffle to smooth the flow
-A vernier hook and point gauge is provided to measure the height of water level
in the channel

<Speficications> HB013 Flow Over a Notch

Model OSC 77FD 013HB
Size（HxWxD)　165 x 245 x 5 mm
Plastic weir plates
Type : Rectangular notch, V notch（60°, 90°）
Point gauge Renge : 0～150mm　Reading : 0.05mm
Size （WxLxH) Approx. 200x600x100mm
Weight Approx. 4kg

<Features>
-This equipment is designed to determine the metacentric height of a floating
body and the hegith variation with the tilt angle
-The equipment consists of a rectangular pontoon
-The center of gravity of the pontoon can be moved sideways by moving horizontal
jockey weight
-The angle of tilt of the pontoon is indicated by a plumb-bob on a scale attached
-The center of gravity of the pontoon can also be moved vertically by means of
adjustable vertical weights on the mast and is determined by a special tool
with a knife edge

<Speficications>
Model OSC 77FD014HB
Size （LxWxH)：400ｘ200ｘ100mm
Pontoon
5mm thick plastics ror as requested
Horizontal scale 1mm graduation
Mast height 450mm or as requested　ｘ　1mmg graduation
Max. angle of tilt ±13°ｘ　0.5°graduation 014HB
Vertical sliding weight 500g Metacentric Height
Jockey weight 200g
Size （WxLxH) Approx. 220ｘ400ｘ480mm
Weight Approx. 3kg
OSC 77FD100HB Optional Accessories

<Features>
-Bernoulli's theorem is applied on flow through a clear acrylic Venturi tube
-Static pressure at various points along the watt of a transperent Venturi tube are
directly meatured on a manometer equiped with a vent valve and a hand air pump
-A movable stainless steel total head probe is also provided
-Flow through the Venturi tube is controlled by a valve at the outlet
-As a primary flow measuring device, coefficient of discharge for the Venturi tube
can be determined
-The appatatur has a hose with amale quick coupling to connection to the Hydraulic Bench

<Speficications>
Model OSC 77FD 015HB
Deimeter 28mm with 14mm throat
Taper Upstream 21°, downstream 10°or as required 　　015HB
Water manometer 8tubes　ｘ　500mm ｘ 1mm graduation Bernoulli's Theorem Apparatus
Size （WxLxH) Approx. 360ｘ600ｘ83mm
Weight Approx. 6kg
＊Option :　HF010 Flow meter, up to　35L/m to facilitate the experiments

<Features>
-This equipment determined the coefficients of discharge for different flow measuring device
-The equipment consists of a Venturi tube, an orifice plate, and
a Pitot tube made from a clear acrylic, connected in series
-Pressure drop across each device is connected to a water manometer
bank with a vent valve and a hand air pump
-The apparatus has a hose with a quick male coupling for connection to
the Hydraulics Bench

<Speficications>
Model OSC 77FD 016HB
Variable area flow meter up to 35L/m
29mm with 17mm throat or as required
Venturi diameter
21° or 14° taper
Orifice plate dia. 20mm on 29mm diameter tube
Pitot tube On 19mm diameter tube
Water manometer 8 tube　ｘ　500mm ｘ 1mm graduation
Size （WxLxH) Approx. 360ｘ720ｘ780mm
Weight Approx. 16kg
016HB Flow Meters
OSC 77FD100HB Optional Accessories

<Features>
-This equipment provides measurement of force developed by a water jet on difference
stationary targets
-The equipment consists of a removable clear acrylic cylinder
-Water is supplied through a tube at the bottom of the cylinder and discharged vertically
through a nozzle onto a target plate
-Each plate maintains the same working distance from the nozzle
-A clear acrylic guard is provided to prevent water jet from splashing on the target
-Force on the plate pushes itsstem upward
-Dead weight is then applied on the stem to counter balance the force exerted by the
water jet
-This balance is indicated by a pointer on a steel rod next to the weight
-The apparatus rests on adjustable footings and a bull's eye level is provided
-The apparatus has a hose with quick male coupling for connection to the Hydraulics Bench

020HB Impact of a Jet

<Speficications>
Model OSC 77FD 020HB
Cylinder diameter 200mm
Nozzle diameter 7mm or as required
Target plate diameter 36mm or are required
Target plates Flat 120°cone, 180°hemisphere
Nozzle and target plate material Plastics or as required
Weights 10gｘ2, 20gｘ2, 50gｘ2, 100gｘ2, 200gｘ2 or weight in N
Size （WxLXH) Approx. 360ｘ350ｘ760mm
Weight 　Approx. 8kg

<Features>
-This equipment is designed to produce and measure free and forced vortices
-The equipment consists of a clear acrylic cylinder on a plinth
-The free vortex is generated by water discharging through an interchangeable
orifice at the base of the cylinder and the resulting profile is measured by a
combined caliper and depth scale
-The forced vortex is generated by a paddle at the base of the cylinder which is
rotated by jets of water, and the profile is measured by a series of depth gauge
-The velocity at any point is the free and forced vortices may be measured
using a pitot tube
-The apparatus has a hose with quick male coupling for connection to the
Hydraulics Bench 022HB Free and Force Vortex,
Rotating Paddle
<Speficications>
Model OSC 77FD 022HB
Cylinder diameter 250mm
Height to over flow point 180mm
Orifice diameters 8, 12, 16 and 24mm
Distance from center of depth probe 0, 30, 50, 70, 90 and 110mm
Pitot tube measuring point 15, 25 and 30mm radius
Size （WxLxH) Approx. 360ｘ680ｘ400mm
Weight Approx. 8kg
OSC 77FD100HB Optional Accessories

<Features>
-This equipment demonstarates Francis turbine characteristics i.e. rotque, power and
efficiency at different speeds for various heads and flow rates of water
-The turbine adjustable guide vanes direct water spirally to the runner
-Inlet pressure is indicated by a pressure gauge
-Torque is measured by a prony brake with two spring balances
-Speed is indicated on a portable tachometer which is separetely supplied
-Flow rate is measured by the Hydraulics Bench measuring tank
-The apparatus has a hose with a quick male coupling for connection to
the Hydraulics Bench

023HBF Mini Francis Turbine

<Speficications>
Model OSC 77FD 023HBF OSC 77FD 023HBK
65mm diameter, 6 section bronze runner 33.5mm diameter 24 blades stainless steel runner
Stainless steel shaft and non corrosion metal housing
Construction 7 adjustable stainless steel guide vanes
Oil seal on hardened shaft sleeve
Transparentwindow
　　Max. speed : approx.　350rmp 　　Max. speed : approx.　5500rmp
Rating
Max. power over 20W from 0.37kW pump
　　Pressure :　0～3kg/cm2 pressure gauge
Instrument Torque　:　2 ea. Spring balances
Speed : Portable tachometer (option)
Size 　　Approx. 300ｘ530ｘ300mm （WxLXH)
Weight 　　Approx. 8.5kg

<Features>
-This equipment demonstrates Pelton turbine characteristics i. e. torque, power
and efficiency at different speeds for various heads and flow rates of water
-The turbine nozzle directs water jet to the runner buckets
-Nozzle pressure is indicated by a pressure gauge
-Torque is neasured by a prony brake with two spring balances
-Speed is indicated on a portable tachometer which is separately supplied
-Flow rate is measured by the Hydraulics Bench measuring tank
-The apparatus has a hose with a quick male coupling for connection to the
Hydraulics Bench

<Speficications>
Model OSK 77FD 023HBP 023HBP
　　160mm diameter stainless steel runner Mini Pelton Turbine
Adjustable stainless steel nozzle, shaft and housing
Construction
Mechanical seal
Transperent window
　　Maximum speed approx. 1500rmp
Rating
Maximum power over 30W for 0.37ｋW pump
　　Pressure :　0～3kg/cm2 pressure gauge
Instruments 　Torque : 　2 ea, spring balances
Speed : Potable tachmeter (option)
Size （WxLXH) 　　Approx. 360ｘ450ｘ700mm
Weight 　　Approx. 17kg