Mvi69 DNP User Manual

MVI69-DNP
CompactLogix or MicroLogix Platform

DNP 3.0 Master/Slave Communication
Module
11/3/2008
USER MANUAL
Please Read This Notice
Successful application of this module requires a reasonable working knowledge of the Rockwell Automation
CompactLogix or MicroLogix hardware, the MVI69-DNP Module and the application in which the combination is to be
used. For this reason, it is important that those responsible for implementation satisfy themselves that the
combination will meet the needs of the application without exposing personnel or equipment to unsafe or
inappropriate working conditions.
This manual is provided to assist the user. Every attempt has been made to ensure that the information provided is
accurate and a true reflection of the product's installation requirements. In order to ensure a complete understanding
of the operation of the product, the user should read all applicable Rockwell Automation documentation on the
operation of the Rockwell Automation hardware.
Under no conditions will ProSoft Technology be responsible or liable for indirect or consequential damages resulting
from the use or application of the product.
Reproduction of the contents of this manual, in whole or in part, without written permission from ProSoft Technology
is prohibited.
Information in this manual is subject to change without notice and does not represent a commitment on the part of
ProSoft Technology Improvements and/or changes in this manual or the product may be made at any time. These
changes will be made periodically to correct technical inaccuracies or typographical errors.
Battery Life Advisory

All modules in the MVI series use a rechargeable Lithium Vanadium Pentoxide battery to backup the 512K SRAM
memory, real-time clock, and CMOS. The battery should last for the life of the module.
The module must be powered for approximately twenty hours before it becomes fully charged. After it is fully charged,
the battery provides backup power for the CMOS setup and configuration data, the real-time clock, and the 512K
SRAM memory for approximately 21 days.
Before you remove a module from its power source, ensure that the battery within the module is fully charged. A fully
charged battery will hold the BIOS settings (after being removed from its power source) for a limited number of days.
When the battery is fully discharged, the module will revert to the default BIOS settings.
Note: The battery is not user replaceable.
Your Feedback Please

We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,
compliments or complaints about the product, documentation or support, please write or call us.
ProSoft Technology
1675 Chester Avenue, Fourth Floor
Bakersfield, CA 93301
+1 (661) 716-5100
+1 (661) 716-5101 (Fax)
http://www.prosoft-technology.com
Copyright © ProSoft Technology, Inc. 2000 - 2008. All Rights Reserved.
MVI69-DNP User Manual
11/3/2008
ProSoft Technology ®, ProLinx ®, inRAx ®, ProTalk® and RadioLinx ® are Registered Trademarks of ProSoft
Technology, Inc.
ProSoft® Product Documentation
In an effort to conserve paper, ProSoft Technology no longer includes printed manuals with our product shipments.
User Manuals, Datasheets, Sample Ladder Files, and Configuration Files are provided on the enclosed CD and are
available at no charge from our web site: http://www.prosoft-technology.com
Printed documentation is available for purchase. Contact ProSoft Technology for pricing and availability.
Asia Pacific: +603.7724.2080
Europe, Middle East, Africa: +33.5.34.36.87.20
Latin America: +1.281.298.9109
North America: +1.661.716.5100
Contents MVI69-DNP ♦ CompactLogix or MicroLogix Platform
DNP 3.0 Master/Slave Communication Module
Contents
Please Read This Notice 2

Battery Life Advisory ........................................................................................................................... 2
Your Feedback Please........................................................................................................................ 2
ProSoft® Product Documentation....................................................................................................... 3
Guide to the MVI69-DNP User Manual 7
1 Start Here 9
1.1 System Requirements ............................................................................................... 9
1.2 Package Contents ................................................................................................... 10
1.3 Setting Jumpers ...................................................................................................... 11
1.4 Install the Module in the Rack ................................................................................. 12
1.5 Connect your PC to the Processor.......................................................................... 15
1.6 Download the Sample Program to the Processor................................................... 16
1.7 Connect your PC to the Module .............................................................................. 19
2 Configuring the MVI69-DNP Module 21

2.1 Configuration File .................................................................................................... 21
2.2 MVI69-DNP Communication Module Configuration................................................ 23
2.3 Slave List................................................................................................................. 29
2.4 Command List .........................................................................................................29
2.5 Uploading and Downloading the Configuration File................................................ 34
3 Ladder Logic 41
3.1 Module Data Objects............................................................................................... 41
3.2 Special Objects ....................................................................................................... 45
3.3 Adding the Module to an Existing CompactLogix Project ....................................... 47
3.4 Adding the Module to an Existing MicroLogix Project............................................. 50
4 Diagnostics and Troubleshooting 53

4.1 Reading Status Data from the Module .................................................................... 53
4.2 LED Status Indicators.............................................................................................. 66
5 Reference 69
5.1 Product Specifications............................................................................................. 69
5.2 Functional Overview................................................................................................ 72
5.3 Cable Connections .................................................................................................. 89
5.4 Error Status Table ................................................................................................... 95
5.5 Internal Indication Word ........................................................................................103
5.6 DNP V3.00 Device Profile Document....................................................................104
ProSoft Technology, Inc. Page 5 of 129

November 3, 2008
Contents MVI69-DNP ♦ CompactLogix or MicroLogix Platform
5.7 DNP Subset Definition - Slave.............................................................................. 105

5.8 DNP Subset Definition - Master............................................................................ 112
6 Support, Service & Warranty 119

6.1 How to Contact Us: Technical Support................................................................. 119
6.2 Return Material Authorization (RMA) Policies and Conditions ............................. 120
6.3 LIMITED WARRANTY .......................................................................................... 122
Index 127
Page 6 of 129 ProSoft Technology, Inc.

November 3, 2008
Start Here MVI69-DNP ♦ CompactLogix or MicroLogix Platform
Guide to the MVI69-DNP User Manual

Function Section to Read Details
Introduction → Start Here (page 9) This Section introduces the customer to the
(Must Do) module. Included are: package contents,
system requirements, hardware installation, and
basic configuration.
Verify Communication, → Verifying This section describes how to verify

Diagnostic and Communication communications with the network. Diagnostic
Troubleshooting (page 66) and Troubleshooting procedures.
Diagnostics and
Troubleshooting
(page 53)
Reference → Reference (page 69) These sections contain general references

Product Specifications Functional Overview associated with this product, Specifications, and
(page 72) the Functional Overview.
Functional Overview
Glossary Product
Specifications (page
69)
Support, Service, and → Support, Service This section contains Support, Service and
Warranty and Warranty (page Warranty information.
Index 119) Index of chapters.

November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Start Here

November 3, 2008
1 Start Here
In This Chapter
System Requirements ............................................................................. 9
Package Contents ................................................................................. 10
Setting Jumpers .................................................................................... 11
Install the Module in the Rack ............................................................... 12
Connect your PC to the Processor ........................................................ 15
Download the Sample Program to the Processor.................................. 16
Connect your PC to the Module ............................................................ 19
Installing the MVI69-DNP module requires a reasonable working knowledge of

the Rockwell Automation hardware, the MVI69-DNP Module and the application
in which they will be used.
Caution: It is important that those responsible for implementation can complete the
application without exposing personnel, or equipment, to unsafe or inappropriate working
conditions. Safety, quality and experience are key factors in a successful installation.
1.1 System Requirements

The MVI69-DNP module requires the following minimum hardware and software
components:
Rockwell Automation CompactLogix or MicroLogix processor, with
compatible power supply and one free slot in the rack, for the MVI69-DNP
module. The module requires 800mA of available power.
Important: The MVI69-DNP module has a power supply distance rating of 2 (L43 and L45
installations on first 2 slots of 1769 bus).
Important: For 1769-L23x processors, please make note of the following limitations.
1769-L23-QBFC1B = 800mA at 5Vdc (1 MVI69-DNP will use all 800mA of available power. No
other modules can be used with an MVI69 module connected to this processor).
1769-L23E-QB1B = 1000mA at 5Vdc (1 MVI69-DNP will use 800mA of available power. One
other module can be used on this rack provided it consumes less than 200mA at 5Vdc.
1769-L23E-QBFC1B = 450mA at 5Vdc (no MVI69 module can be used with this processor)
Rockwell Automation RSLogix 5000 (CompactLogix) or RSLogix 500
(MicroLogix) programming software
Rockwell Automation RSLinx communication software

November 3, 2008
Pentium® II 450 MHz minimum. Pentium III 733 MHz (or better)
recommended
Supported operating systems:
o Microsoft Windows XP Professional with Service Pack 1 or 2
o Microsoft Windows 2000 Professional with Service Pack 1, 2, or 3
o Microsoft Windows Server 2003
128 Mbytes of RAM minimum, 256 Mbytes of RAM recommended
100 Mbytes of free hard disk space (or more based on application
requirements)
256-color VGA graphics adapter, 800 x 600 minimum resolution (True Color
1024 × 768 recommended)
CD-ROM drive
HyperTerminal or other terminal emulator program capable of file transfers
using Ymodem protocol.
1.2 Package Contents

The following components are included with your MVI69-DNP module, and are
all required for installation and configuration.
Important: Before beginning the installation, please verify that all of the following items are
present.
Qty. Part Name Part Number Part Description
1 MVI69-DNP MVI69-DNP DNP 3.0 Master/Slave Communication Module
Module
1 Cable Cable #15, RS232 For RS232 Connection to the CFG Port
Null Modem
3 Cable Cable #14, RJ45 to For DB9 Connection to Module's Port
DB9 Male Adapter
cable
2 Adapter 1454-9F Two Adapters, DB9 Female to Screw Terminal. For
RS422 or RS485 Connections to Port 1 and 2 of the
Module
1 ProSoft Contains sample programs, utilities and
Solutions CD documentation for the MVI69-DNP module.
If any of these components are missing, please contact ProSoft Technology
Support for replacement parts.

November 3, 2008
1.3 Setting Jumpers

When the module is manufactured, the port selection jumpers are set to RS-232.
To use RS-422 or RS-485, you must set the jumpers to the correct position. The
following diagram describes the jumper settings.
The Setup Jumper acts as "write protection" for the module's flash memory. In
"write protected" mode, the Setup pins are not connected, and the module's
firmware cannot be overwritten. Do not jumper the Setup pins together unless
you are directed to do so by ProSoft Technical Support.

November 3, 2008
1.4 Install the Module in the Rack

This section describes how to install the module into a CompactLogix or
MicroLogix rack
Before you attempt to install the module, make sure that the bus lever of the
adjacent module is in the unlocked (fully right) position.
Warning: This module is not hot-swappable! Always remove power from the rack before
inserting or removing this module, or damage may result to the module, the processor, or other
connected devices.
1 Align the module using the upper and lower tongue-and-groove slots with the
adjacent module and slide forward in the direction of the arrow.
2 Move the module back along the tongue-and-groove slots until the bus
connectors on the MVI69 module and the adjacent module line up with each
other.

November 3, 2008
3 Push the module's bus lever back slightly to clear the positioning tab and
move it firmly to the left until it clicks. Ensure that it is locked firmly in place.
4 Close all DIN rail latches.

November 3, 2008
5 Press the DIN rail mounting area of the controller against the DIN rail. The
latches will momentarily open and lock into place.

November 3, 2008
1.5 Connect your PC to the Processor

1 Connect the right-angle connector end of the cable to your controller at the
communications port.
2 Connect the straight connector end of the cable to the serial port on your
computer.

November 3, 2008
1.6 Download the Sample Program to the Processor
Important: For most applications, the sample program will work without modification.
Note: The key switch on the front of the CompactLogix processor must be in the REM position.
1 If you are not already online to the processor, open the Communications
menu, and then choose Download. RSLogix will establish communication
with the processor.
2 When communication is established, RSLogix will open a confirmation dialog
box. Click the Download button to transfer the sample program to the
processor.
3 RSLogix will compile the program and transfer it to the processor. This
process may take a few minutes.
4 When the download is complete, RSLogix will open another confirmation
dialog box. Click OK to switch the processor from Program mode to Run
mode.
Note: If you receive an error message during these steps, refer to your RSLogix documentation to
interpret and correct the error.

November 3, 2008
1.6.1 Configuring RSLinx
If RSLogix is unable to establish communication with the processor, follow these steps:
1 Open RSLinx.
2 Open the Communications menu, and choose Configure Drivers.
This action opens the Configure Drivers dialog box.
Note: If the list of configured drivers is blank, you must first choose and configure a driver from the
Available Driver Types list. The recommended driver type to choose for serial communication with
the processor is "RS-232 DF1 Devices".

November 3, 2008
3 Click to select the driver, and then click Configure. This action opens the
Configure Allen-Bradley DF1 Communications Device dialog box.
4 Click the Auto-Configure button. RSLinx will attempt to configure your serial
port to work with the selected driver.
5 When you see the message "Auto Configuration Successful", click the OK
button to dismiss the dialog box.
Note: If the auto-configuration procedure fails, verify that the cables are connected correctly
between the processor and the serial port on your computer, and then try again. If you are still
unable to auto-configure the port, refer to your RSLinx documentation for further troubleshooting
steps.

November 3, 2008
1.7 Connect your PC to the Module

With the module securely mounted, connect your PC to the Configuration/Debug
port using an RJ45-DB-9 Serial Adapter Cable and a Null Modem Cable.
1 Attach both cables as shown.
2 Insert the RJ45 cable connector into the Configuration/Debug port of the
module.
3 Attach the other end to the serial port on your PC or laptop.

November 3, 2008

November 3, 2008
Configuring the MVI69-DNP Module MVI69-DNP ♦ CompactLogix or MicroLogix Platform
2 Configuring the MVI69-DNP Module
In This Chapter
Configuration File .................................................................................. 21
MVI69-DNP Communication Module Configuration .............................. 23
Slave List............................................................................................... 29
Command List ....................................................................................... 29
Uploading and Downloading the Configuration File............................... 34
2.1 Configuration File

The MVI69-DNP module stores its configuration in a text file called DNP.CFG,
located in the module's flash memory. When the module starts up, it reads the
configuration file and uses the information to control how the DNP 3.0
Master/Slave protocol interacts with the module's application port(s).
The configuration file is arranged in Sections, with a heading in [ ] characters at
the beginning of each section. Each Section contains a list of Parameters and
Values, followed by an optional Comment that explains the parameter.
The following illustration shows an example of a Section, a Parameter, a Value,
and a Comment.
The Parameter must be followed by a [:] (colon) character. The text following the
[:] is a Value.
The module ignores "comment" text following the [#] character. Use comments to
document your configuration settings.
You can get a sample configuration file for the module in the following places:
Copy (page 34) the DNP.CFG from the module's flash memory to your PC
Copy the DNP.CFG from the ProSoft Solutions CD-ROM supplied with the
module
Download the DNP.CFG from the ProSoft Technology web site at
http://www.prosoft-technology.com
November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Configuring the MVI69-DNP Module
2.1.1 Editing the Configuration File

The DNP.CFG file is a plain ASCII text file. Use a text editor such as
Notepad.exe (included with Microsoft Windows) to open and edit the file.
To open the configuration file in Notepad
1 Click the Start button, and then choose Programs
2 Expand the Programs menu, and then choose Accessories.
3 On the Accessories menu, choose Notepad.
4 In Notepad, open the File menu, and then choose Open
5 In the Open dialog box, select "All Files" in the Files of Type: dropdown list.
Tip: Sample configuration files are stored under the LadderLogic folder on the ProSoft Solutions
CD-ROM.
6 Navigate to the folder containing the configuration file, and then select the file
to edit.
7 Click Open to open the file.
8 When you have finished editing, save the file and close Notepad.
Important: Changes to the configuration file will not take effect until you download the file to the
module, and then reboot the module.

November 3, 2008
2.2 MVI69-DNP Communication Module Configuration

[Section]/Item Value Range Description
[MODULE] General module configuration section
Module Name: 0 to 80 This parameter assigns a name to the module that can
characters be viewed using the configuration/debug port. Use this
parameter to identify the module and the configuration
file.

[DNP Slave] DNP Slave configuration information
Internal Slave ID: 0 to 65534 This is the DNP address for the module. All messages
with this address from the master will be processed by
the module.
Baud Rate: Baud rate value Primary DNP Port Baud Rate: 300, 600, 1200, 2400,
4800, 9600, 19200, 384 (38400) , 576 (57600), 115
(115200)
RTS On: 0 to 65535 This value represents the number of 1 ms increments
milliseconds to be inserted between asserting the RTS modem line
and the actual transmission of the data.
RTS Off: 0 to 65535 This value represents the number of 1 ms increments
milliseconds to be inserted after the last character of data is
transmitted before the RTS modem line is dropped.
Min Response Delay: 0 to 65535 Minimum time between receiving a request and
milliseconds transmitting a response. Allows master time to disable
transmitter on an RS-485 network.
Modem: Yes or No This parameter defines if a dial-up modem is used on
the secondary DNP slave port. A modem cannot be
used if the port is configured as a master.
Connect Timeout: 0 to 65535 Defines the number of milliseconds to wait for the CD
signal to be set high. The CD signal indicates a
connection is made using a dial-up modem.
First Character Delay: 0 to 65535 Defines the number of milliseconds to wait before
sending the first message after the connection is first
made. This delay only applies to the first packet sent to
the modem.
Redial Delay Time: 0 to 32000 Defines the minimum number of milliseconds to wait
before a redial attempt is made by the slave.
Redial Random Delay: 0 to 32000 Defines a random millisecond time range to be added
to the redial delay time before the modem is accessed.
Idle Timeout: 0 to 65535 Defines the number of milliseconds the modem is
inactive before it will disconnect.
Phone Number: ASCII String This field contain a null-terminated, ASCII character
Data string used by the dial-up modem. The string must
contain all characters required by the modem. An
example string is ATDT1800222333. Maximum length
is 34 bytes including the terminating 0.
Collision Avoidance: Yes or No This parameter defines if collision avoidance will be
utilized on the primary DNP slave port.
CD Idle Time: 0 to 32000 Defines the minimum number of milliseconds to wait
before transmitting a message after the CD signal is
recognized as low.
CD Random Time: 0 to 32000 Defines the range of random time to be added to the
CD Idle Time before a message will be transmitted
from the slave.

November 3, 2008

CD Time Before Receive: 0 to 65535 Defines the number of milliseconds to wait before
receiving characters after the CD signal is recognized
as high.
BI Class: 0 to 3 This parameter specifies the default class to be utilized
for all the binary input points in the DNP database that
are not defined in the override list section.
AI Class: 0 to 3 This parameter specifies the default class to be utilized
for all the analog input points in the DNP database that
are not defined in the override list section.
Float Class: 0 to 3 This parameter specifies the default class to be utilized
for all the floating-point input points in the DNP
database that are not defined in the override list
section.
AI Deadband: 0 to 32767 This parameter specifies the default deadband value
assigned to all points not defined in the override list for
the analog input point type in the DNP database.
Float Deadband: 0 to maximum This parameter specifies the default deadband value
float value assigned to all points not defined in the override list for
the floating-point input point type in the DNP database.
Select/Operate Arm Time: 1 to 65535 Time period after select command received in which
milliseconds operate command will be performed. After the select
command is received, the operate command will only
be honored if it arrives within this period of time.
Write Time Interval: 0 to 1440 Time interval to set the need time IIN bit (0=never),
minutes which will cause the master to write the time. Stored in
milliseconds in the module memory.
Data Link Confirm Mode: Coded Value IED can request acknowledgement from master station
(N=Never, when sending data. The codes are as follows:
S=Sometimes, 0=Never, 1=Sometimes, 2=Always
A=Always)
Data Link Confirm Tout: 1 to 65535 Time period to wait for Master Data Link confirmation
milliseconds of last frame sent. This time is in milliseconds. This
parameter is only used if the frame is sent with
confirmation requested.
Data Link Max Retry: 0 to 255 retries Maximum number of retries at the Data Link level to
obtain a confirmation. If this value is set to 0, retries
are disabled at the data link level of the protocol. This
parameter is only used if the frame is sent with
confirmation requested.
App Layer Confirm Tout: 1 to 65535 Event data contained in the last response may be sent
milliseconds again if not confirmed within the millisecond time
period set. If application layer confirms are used with
data link confirms, ensure that the application layer
confirm timeout is set long enough.
Unsolicited Response: Yes or No Set if the slave unit will send unsolicited response
messages. If set to No, the slave will not send
unsolicited responses. If set to Yes, the slave will send
unsolicited responses.
Class 1 Unsol Resp Min: 1 to 255 events Minimum number of events in Class 1 required before
an unsolicited response will be generated.

November 3, 2008

Unsol Resp Delay: 0 to 65535 Maximum number of 1 millisecond intervals to wait
milliseconds after an event occurs before sending an unsolicited
response message. If set to 0, only use minimum
number of events.
Uresp Master Address: 0 to 65534 DNP destination address where unsolicited response
messages are sent.
Uresp Retry Count: 0 to 255 retries Determines the number of unsolicited message retries
sent on primary DNP port before changing to
secondary port. If the value is 0, port switching will be
disabled.
AI Events with time: Yes or No This parameter sets if the analog input events
generated by the module will include the date and time
of the event. If the parameter is set to No, the default is
set to no time data. If the parameter is set to Yes, the
default object will include the time of the event.
Time Sync Before Events: Yes or No This parameter determines if events are to be
generated by the module before the time
synchronization from the master unit. If the parameter
is set to No, no events will be generated until the
module's time has been synchronized. If the parameter
is set to Yes, events will always be generated.
Initialize DNP Database: Y or N This parameter determines if the module will request
data from the processor to initialize the DNP database
output data areas. If this option is utilized, ladder logic
is required to send the requested block from the
processor to the module.
Use Trip/Close Single Point Y or N Used for backwards compatibility with older MVI69-
DNP modules, will cause Trip/Close operations to use
a single point operation.

[DNP Slave Database] DNP Slave Database definition
Binary Inputs: 0 to 7680 Number of digital input points to configure in the DNP
points slave device. Each point will be stored as a single bit in
the module memory.
PLC Binary Inputs: 0 to 7680 Number of digital input points configured above that
points are to be obtained from the CompactLogix processor.
All other binary input points must come from the
attached IED units.
Analog Inputs: 0 to 480 points Number of analog input points to configure in the DNP
slave device. Each point will occupy a one word area
in the module memory.
PLC Analog Inputs: 0 to 480 points Number of analog input points configured above that
are to be obtained from the CompactLogix processor.
All other analog input points must come from the
attached IED units.
Float Inputs: 0 to 240 points Number of floating-point input points to configure in the
DNP slave device. Each point will occupy a two-word
area in the module memory.
PLC Float Inputs: 0 to 240 points Number of floating-point input points configured above
that are to be obtained from the PLC.
Counters: 0 to 240 points Number of counter points to configure in the DNP
slave device. Each point will occupy a two word area in
the module memory. This number corresponds to the
number of frozen counters. The application maps the
counters to the frozen counters directly.
November 3, 2008

PLC Counters: 0 to 240 points Number of counter points configured above that are to
be obtained from the CompactLogix processor. All
other counter points must come from the attached IED
units.
Binary Outputs: 0 to 7680 Number of digital output points to configure in the DNP
points slave device. Each point will be stored as a single bit in
the module memory.
PLC Binary Outputs: 0 to 7680 Number of digital output points configured above that
points are to be sent to the CompactLogix processor. All
other binary output points will be sent to the attached
IED units.
Analog Outputs: 0 to 480 points Number of analog output points to configure in the
DNP slave device. Each point will occupy a one word
area in the module memory.
PLC Analog Outputs: 0 to 480 points Number of analog output points configured above that
are to be sent to the CompactLogix processor. All
other analog output points will be sent to the attached
IED units.
Float Outputs: 0 to 240 points Number of floating-point output points to configure in
the DNP slave device. Each point will occupy a two-
word area in the module memory.
PLC Float Outputs: 0 to 240 points Number of floating-point output points configured
above that are to be sent to the CompactLogix.
[Section]/Item Description
[DNP Slave Binary Inputs] DNP database binary input override values
# This area is to override the class assignment for binary input database points. Enter list of points between the
# START and END labels.
#
# Point# Class
START
END
[DNP Slave Analog Inputs] DNP database analog input override values
START
# This area is to override the class and deadband assignment for analog input database points.
# Enter list of points between the START and END labels.
#
# Point# Class Deadband
START
END
[DNP Slave Float Inputs] DNP database floating-point input override values
# This area is to override the class and deadband assignment for float input database points.
# Enter list of points between the START and END labels.
#
# Point# Class Deadband

November 3, 2008
START
END

[Secondary Port] Definitions for secondary port on module
Type: M or S or blank This parameter defines the functionality of the
secondary port on the module.
M = emulate a DNP master port
S = back-up DNP slave port to the primary port.
Any other value will disable the port.
Baud Rate: Baud rate Secondary DNP Port Baud Rate: 300, 600, 1200,
value 2400, 4800, 9600, 19200, 384 (38400) , 576 (57600),
115 (115200)
RTS On: 0 to 65535 This value represents the number of 1 ms increments
milliseconds to be inserted between asserting the RTS modem line
and the actual transmission of the data.
RTS Off: 0 to 65535 This value represents the number of 1 ms increments
milliseconds to be inserted after the last character of data is
transmitted before the RTS modem line is dropped.
Min Response Delay: 0 to 65535 Minimum time between receiving a request and
milliseconds transmitting a response. Allows master time to disable
transmitter on an RS-485 network.
Collision Avoidance: Yes or No This parameter defines if collision avoidance will be
utilized on the primary DNP slave port.
CD Idle Time: 0 to 32000 Defines the minimum number of milliseconds to wait
before transmitting a message after the CD signal is
recognized as low.
CD Random Time: 0 to 32000 Defines the range of random time to be added to the
CD Idle Time before a message will be transmitted
from the slave.
CD Time Before Receive: 0 to 65535 Defines the number of milliseconds to wait before
receiving characters after the CD signal is recognized
as high.

[DNP Master] Definitions for DNP Master port if utilized.
Internal ID: 0 to 65534 This is the DNP address for the module. All messages
with this address from the master will be processed by
the module.
Initialize IED Database: Yes or No This parameter determines if the module will request
data from the processor to initialize the IED database
input data areas. If this option is utilized, ladder logic is
required to send the requested block from the
processor to the module.
Event Messages to PLC: Yes or No This parameter determines if event messages received
on the master port will be sent to the processor. If this
option is utilized, ladder logic must handle the 9903
blocks generated by the module.

November 3, 2008

[IED Database] Database definition for DNP master port if utilized
Binary Inputs: 0 to 7680 Number of binary input points contained in the IED
points database to transfer to the CompactLogix processor
and obtained from the attached IED units..
Analog Inputs: 0 to 480 points Number of analog input points contained in the IED
database to transfer to the CompactLogix processor
Counters: 0 to 240 points Number of counter points contained in the IED
database to transfer to the CompactLogix processor
Binary Outputs: 0 to 7680 Number of binary output points contained in the IED
points database which are transferred from the CompactLogix
processor and used by the attached IED units..
Analog Outputs: 0 to 480 points Number of analog output points contained in the IED
database which are transferred from the CompactLogix
processor and used by the attached IED units..
[DNP Master Slave List] Definition of the IED units to be interfaced with the
DNP master port if utilized
# This section stores information about each slave to be used by the master port.
# There must be an entry in this table for each node to be used in the command list.
# Two of the parameters in this list are coded values:
# Conf Mode ==> 0=Never, 1=Sometimes and 2=Always (select 0).
# Flags is bit coded as follows:
# Bit 0 (decimal 1) ==> Enable the slave
# Bit 1 (decimal 2) ==> Use Unsolicited messaging with this slave
# Bit 2 (decimal 4) ==> Use delay measurement with this slave
# Bit 3 (decimal 8) ==> Auto time synchronization enabled
#
# Node DL Conf Conf Conf App Rsp
# Address Mode Timeout Retry Timeout Flags
START
END
[DNP Master Commands] Definition of the commands to be issued to the IED
units by the DNP master port.
# This section contains the list of commands to process on the master port.
# Node addresses present in the command list must have an entry in the
# [DNP Slave List]. Commands with nodes not present in the list will not be
# executed.
# 1 2 3 4 5 6 7 8 9 10
#Flags/ Node Data Data Cmd Device Point DNP DB IED DB Poll
#Enable Address Object Variation Func Address Count Address Address Interval
START
END

November 3, 2008
2.3 Slave List

The slave list defines the IED units and their specific communication parameters
for a DNP master port. Up to 40 IED units can be defined in the module to be
associated with the master port. The structure of each row in the list is defined in
the following table.
Column Variable Name Data Range Description If Error
1 DNP Slave Address 0 to 65534 This is the slave address for the unit to Ignore
override the default values.
2 Data Link Confirm Mode Coded Value This value specifies if data link frames sent 0
(0 = Never, 1 = to the remote device require a data link
Sometimes, confirm. This value should always be set to
2 = Always) zero for almost all applications.
3 Data Link Confirm Tout 1 to 65535 This parameter specifies the time to wait for 300
milliseconds a data link confirm from the remote device
before a retry is attempted.
4 Maximum Retries for Data 0 to 255 retries Maximum number of retries at the Data Link 3
Link Confirm level to obtain a confirmation. If this value is
set to 0, retries are disabled at the data link
level of the protocol. This parameter is only
used if the frame is sent with confirmation
requested.
5 Application Layer Response 1 to 65535 Timeout period the master will wait for each 5000
Timeout milliseconds response message fragment. If data link
confirms are enabled, make sure the
timeout period is set long enough to permit
all data confirm retries.
6 Slave Mode Coded Value (Bit This word contains bits that define the slave
0 = Enable, Bit 1 mode. The slave mode defines the
= Unsol Msg., Bit functionality of the slave device and can be
2 = Use DM, Bit combined in any combination. The fields
3 = Auto Time have the following definition: Enable:
Sync) determines if this slave will be used. Unsol
Msg.: causes an enabled unsolicited
message to be sent to the slave when its
RESTART IIN bit is set. This parameter is
also required for unsolicited message
reporting by the IED unit. Use DM: uses
delay measurement. Auto Time Sync: time
synchronization used when NEED TIME IIN
bit set.
2.4 Command List

The command list stores the command list used by the DNP master port. This list
only must be defined if the DNP master port is used. Up to 300 commands can
be defined for the master port. The structure of each row in the list is shown in
Word Offset Definitions
0 Port/Flags
1 Slave Address
2 Object
3 Variation
4 Function

November 3, 2008
Word Offset Definitions

5 Address in Slave
6 Point Count
7 DNP DB Address
8 IED DB Address
9 Poll Interval
The definition of each parameter required for each command is provided in the
following table.
Bits in the Port/Flags parameter are dependent on the data type. The following
table defines the Port/Flags bits for binary input, analog input and counter data
points.
Port/Flags Bits Description Decimal Equivalent
0 to 1 Communication port (0=Internal, 2=Port 2) 0 or 2
2 Enable/Disable Command (1=Enable, 0=Disable) 4
3 RBE Flag (0=Events from IED, 1=Events by module) 8
4 to 7 Not Used
For these data types the qualifier used in the data request is dependent on the
Point Count and Address in Slave fields in the command as follows:
If Point Count < 0, then use Qualifier 06h (All points, packed & -Point Count =
# of points to consider)
If Address in Slave = 0 & Point Count > 0, then use Qualifier 00h or 01h
(points 0 to Point Count -1)
If Address in Slave > 0 & Point Count > 0, then use Qualifier 00h or 01h
(Address in Slave to Address in Slave + Point Count - 1)
The following table defines the Port/Flags bits for binary output and analog output
points.
Port/Flags Bits Description Decimal Equivalent
0 to 1 Communication port (0=Internal, 2=Port 2) 0 or 2
2 Enable/Disable Command (1=Enable, 0=Disable) 4
3 Poll Type (0=Poll, 1=Exception) 8
4 Data Source (0=DNP Database, 1=IED Database) 16
5 to 7 Not Used
For these data types the qualifier used in the data request is dependent on the
Point Count and Address in Slave fields in the command as follows:
If Address in Slave = 0 & Point Count > 0, then use Qualifier 17h or 28h (Point
Count specified starting at point 0)
If Address in Slave > 0 & Point Count > 0, then use Qualifier 17h or28h (points
from Address in Slave to Address in Slave + Point Count - 1)
If Point Count <= 0, then ignore because this is illegal for outputs.
Digital input Digital input Events Digital Output Counter
0 Port/Flags Port/Flags Port/Flags Port/Flags
1 Slave Address Slave Address Slave Address Slave Address
2 1 2 12 20
3 0, 1 or 2 0, 1, 2 or 3 1* 0, 5 or 6
4 1* 1* 3, [4], 5 or 6 1, 7, 8, 9 or 10
5 Address in Slave Address in Slave Address in Slave Address in Slave

November 3, 2008
Digital input Digital input Events Digital Output Counter

6 # of Points # of Points # of Points # of Points
7 DNP DB Address DNP DB Address DNP DB Address
8 IED DB Address IED DB Address IED DB Address
9 Poll Interval Poll Interval Poll Interval Poll Interval
Frozen Counter Analog Input Analog Input Analog Output

Events
2 21 30 32 41
3 0, 9 or 10 0, 1, 2, 3 or 4 0, 1, 2, 3 or 4 2*
4 1* 1* 1* 3, [4], 5 or 6
5 Address in Slave Address in Slave Address in Slave Address in Slave
6 # of Points # of Points # of Points # of Points
7 DNP DB Address DNP DB Address DNP DB Address
8 IED DB Address IED DB Address IED DB Address
Time and Date Class 0 Class 1 Class 2

2 50 60 60 60
3 1* 1 2 3
4 2*
5
6 1 1 1 1
7
8
Class 3 Cls 1, 2 & 3 Cls 0, 1, 2 & 3 [Clear Restart Bit]

2 60 60 60 80
3 4 5 6 1
4 2
5 7
6 1 1 1 1
7
8
9 Poll Interval Poll Interval Poll Interval

November 3, 2008
Cold Restart Warm Restart Enable Unsol. Msg Disable Unsol. Msg
2 0 0 0 0
3
4 13 14 20 21
5
6 1 1 1 1
7
8
9
* Value assumed
[ ] Automatically implemented Word Offset Definitions
0 Port/Flags
1 Slave Address
2 Object
3 Variation
4 Function
5 Address in Slave
6 Point Count
7 DNP DB Address
8 IED DB Address
9 Poll Interval
Commands are issued based on the following criteria:
Commands Issued Each Scan Enabled
Poll Interval = 0
BO & AO have Exception Bit = 0
Commands Issued at Poll Time Enabled
Poll Interval > 0
BO and AO have Exception Bit = 0
Commands Issued on Data Change (BO and Enabled
AO) BO and AO have Exception Bit = 1
Commands Issued by PLC

November 3, 2008
2.4.1 Slave Address

This parameter specifies the IED unit address on the DNP network to consider
with the command. The parameter has a range of 0 to 65535. The value of
65535 is reserved for broadcast messages. Verify that the slave configuration
information is set up in the module for each slave defined in the command list.
2.4.2 Object
This parameter specifies the DNP object type in the command. Valid objects for
the module are 1, 2, 12, 20, 21, 30, 32, 41, 50, 60 and 80. A value of 0 is
permitted in this field for a set of special commands.
2.4.3 Variation
This parameter is specific to the object type selected.
2.4.4 Function
This parameter specifies the DNP function for the command list object. The
object type determines the value of the functions permitted. For example, the
only function permitted for binary input data points is the read function (Function
Code 1). For counter and output objects, more functions are available.
2.4.5 Address In Slave

This value must be greater-than or equal to zero. If it is set to a value less-than
zero, the command will be ignored. This parameter specifies the starting point
address to consider in the IED unit.
2.4.6 Point Count

This parameter defines the number of points in the IED unit. Refer to the
discussion above for the interpretation of this parameter's values for the different
object types.
2.4.7 DNP DB Address

This parameter defines the starting location in the DNP database to be used with
the command. If the parameter has a value of -1, the DNP database is not used
with the point.
2.4.8 IED DB Address

This parameter defines the starting location in the IED database to be used with
the command. If the parameter has a value of -1, the IED database is not used
with the point.

November 3, 2008
2.4.9 Poll Interval

This parameter specifies the minimum frequency at which the module should
execute the command. The value is entered in units of seconds. For example, to
execute a command every 10 seconds, enter a value of 10 in the field. A value of
0 for the parameter implies that the command should be executed every scan of
the list.
2.5 Uploading and Downloading the Configuration File

ProSoft modules are shipped with a pre-loaded configuration file. In order to edit
this file, you must transfer the file from the module to your PC. After editing, you
must transfer the file back to the module.
This section describes these procedures.
Important: The illustrations of configuration/debug menus in this section are intended as a general
guide, and may not exactly match the configuration/debug menus in your own module. For specific
information about the configuration/debug menus in your module, refer to The Configuration/Debug
Menu (page 53).
2.5.1 Transferring the Configuration File to Your PC

1 Connect your PC to the Configuration/Debug port of the module using a
terminal program such as HyperTerminal. Press [?] to display the main
menu.

November 3, 2008
2 Press [>] key (Send Module Configuration). The message "Press Y to

confirm configuration send!" is displayed at the bottom of the screen.
3 Press [Y]. The screen now indicates that the module is ready to send.
4 From the Transfer menu in HyperTerminal, select Receive File. This action
opens the Receive File dialog box.
5 Use the Browse button to choose a folder on your computer to save the file,
and then click Receive.
Note: ProSoft Technology suggests that you download the configuration file pre-loaded on
your module. However, configuration files are also available on the ProSoft CD as well as the
ProSoft Technology web site at http://www.prosoft-technology.com.

November 3, 2008
When the configuration file has been transferred to your PC, the dialog box
will indicate that the transfer is complete.
6 You can now open and edit the file in a text editor such as Notepad. When
you have finished editing the file, save it and close Notepad.
Important: You must name this file DNP.CFG before you transfer it to the module. The module will
not recognize configuration files with any other name or extension.
2.5.2 Transferring the Configuration File to the Module

Perform the following steps to transfer a configuration file from your PC to the
module.
1 Connect your PC to the Configuration/Debug port of the module using a
terminal program such as HyperTerminal. Press [?] to display the main
menu.

November 3, 2008
2 Press [<] (Receive Module Configuration). The message "Press Y key to

confirm configuration receive!" is displayed at the bottom of the screen.
3 Press [Y]. The screen now indicates that the PC is ready to send.

November 3, 2008
4 From the Transfer menu in HyperTerminal, select Send File.
The Send File dialog appears.

November 3, 2008
5 Use the Browse button to locate the configuration file your computer.
Note: This procedure assumes that you are uploading a newly edited configuration file from your
PC to the module. However, configuration files are also available on the ProSoft CD as well as the
ProSoft Technology web site.
6 Select Ymodem as the protocol.

7 Click the Send button. This action opens the Ymodem File Send dialog box.

November 3, 2008
When the upload is complete, the screen indicates that the module has
reloaded program values and displays information about the module.
8 Your module now contains the new configuration. Press [?] to see the
module's main menu.

November 3, 2008
Ladder Logic MVI69-DNP ♦ CompactLogix or MicroLogix Platform
3 Ladder Logic
In This Chapter
Module Data Objects ............................................................................. 41
Special Objects ..................................................................................... 45
Adding the Module to an Existing CompactLogix Project ...................... 47
Adding the Module to an Existing MicroLogix Project............................ 50
Ladder logic is required for application of the MVI69-DNP module. Tasks that
must be handled by the ladder logic are module data transfer, special block
handling and status data receipt. Additionally, a power-up handler may be
needed to handle the initialization of the module's data and to clear any
processor fault conditions.
The sample ladder logic, on the ProSoft Solutions CD-ROM, is extensively
commented, to provide information on the purpose and function of each rung. For
most applications, the sample ladder will work without modification.
3.1 Module Data Objects

All data related to the MVI69-DNP is stored in two user defined data types. One
contains the status data and the other contains the DNP and IED datasets. Two
structures were used for ease of use. Any time an array's size is altered in the
RSLogix 5000 software, all the data in the object is set to zero. Because the
array sizes may need to be adjusted for the data types in an application, this data
is placed in a separate object.
An instance of each data type is required before the module can be used. This is
accomplished by declaring variables of the data types in the Controller Tags Edit
Tags dialog box. Each object is discussed in the following topics:
3.1.1 DNPModuleDef Object

The DNPModuleDef object contains all the MVI69-DNP module status data. The
structure of the object is displayed in the following example:
Tag Name Data Type Description
GenStat DNPSlvStat General status information
ErrList INT[60] List of last 60 slave errors
BP DNPBackplane Data to handle backplane logic
CmdLstErr DNPCmdLstErr
ComErrTble DNPComErrTble
Readclock DNPtime_n_date
WriteClock DNPtime_n_date

November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Ladder Logic

cmd1 DNPCROB
cmd2 DNPCROB
cmd3 DNPCROB
cmd4 DNPCROB
This object contains objects that define the status related to the module. Each of
these object types is discussed in the following topics of the document. The
ErrList member of the object stores the list of last 60 errors generated by the
module. This data is passed to the processor from the module the read block
100. Ladder logic transfers this information from the processor into the ErrList
array.
3.1.2 DNPSlvStat Object

The DNPSlvStat object stores the status data passed from the module to the
processor in the read blocks 112 to 114. This block of data contains information
that can be used to determine the "health" of the module and the tasks running.
The structure of the object is shown in the following example:
Cur_Port Decimal Current DNP Slave port
Last_Err Decimal Last DNP slave error code
Msg_Me Decimal Total message frames for slave
Msg_Sent Decimal Total message frames sent
Msg_Rec Decimal Total message frames received
Err_Sync Decimal Total number of synchronization errors
Err_Overrun Decimal Total number of over runs errors
Err_Length Decimal Total number of length errors
Err_CRC Decimal Total number of CRC errors
Err_Overflow Decimal Total number of overflow errors
Err_Seq Decimal Total number of sequence errors
Err_Address Decimal Total multi-frame request fragment errors
BI_Events Decimal Total number of BI events
BI_Buffer Decimal Total number of BI events in buffer
AI_Events Decimal Total number of AI events
AI_Buffer Decimal Total number of AI events in buffer
Err_Func Decimal Total number of bad function errors
Err_Obj Decimal Total number of object unknown errors
Err_Range Decimal Total number of range errors
Err_MOverflow Decimal Total number of app msg overflow errors
Err_Frame Decimal Total number of multi-frame errors
Blk_Total Decimal Total number of blocks transferred
Blk_Good Decimal Total number of blocks transferred successfully
Blk_Err Decimal Total number of blocks in error
Blk_RErr Decimal Total number of read block errors

November 3, 2008

Blk_WErr Decimal Total number of write block errors
Blk_NErr Decimal Total number of block number errors
Blk_ECntr Decimal Number of sequential block errors
Blk_EFlag Decimal Block error flag
Cfg_Type Decimal 0=Single Slave, 1-Dual-Slave, 2=Slave/Master
Product Decimal Product name
Rev Decimal Revision
Op_Sys Decimal Operating system revision
Run Decimal Run number
Slave_Count Decimal Number of slaves configured
Cmd_Count Decimal Number of commands configured
Mem_Blk Decimal Number of memory blocks allocated
Mem_Frame Decimal Number of frame blocks allocated
Mem_DLRec Decimal Number of receive DL blocks allocated
Mem_DLTx Decimal Number of transmit DL blocks allocated
Mem_AppRec Decimal Number of receive app blocks allocated
Mem_AppTx Decimal Number of transmit app blocks allocated
Mem_DevErr Decimal Number of device mem alloc errors
Mem_PhyErr Decimal Number of physical layer mem alloc errors
Mem_DLRErr Decimal Number of data-link layer receive mem alloc errors
Mem_DLTErr Decimal Number of data-link layer transmit mem alloc errors
Mem_AppRErr Decimal Number of app layer receive mem alloc errors
Mem_AppTErr Decimal Number of app layer transmit mem alloc errors
Mstr_Sync Decimal Number of master port synchronization errors
Mstr_Length Decimal Number of master port length errors
Mstr_CRC Decimal Number of master port CRC errors
Scan_Count Decimal Program scan counter
Mem_Free Decimal Free memory for module
P1_TX_State Decimal State of Port 1 transmit state machine
FloatEvents Decimal Count of floating-point events
DoubleEvents Decimal Count of double floating-point events
EventQueue Decimal Total number of events in message queue for
processor
EvtQueueOF Decimal Event message queue overflow flag (0=no, 1=yes)
Ladder logic is required to transfer the data sent from the module to the
processor into this data object. If the ladder logic is present and the module is
operating, this object can be viewed in the Controller Tags Monitor window to
observer the current status of the module.

November 3, 2008
3.1.3 DNPBackplane Object

The DNPBackplane object stores the variables required for backplane data
transfer between the module and the processor. The structure of the object is
displayed in the following example:
LastRead INT Index of last read block
LastWrite INT Index of last write block
BlockIndex INT Computed block offset for data table
3.1.4 DNPData Object

The DNPData object stores all the data for an MVI69-DNP module. This includes
the data to interface with the DNP slave port (DNP data set) and the DNP master
port (IED data set). Contained within the object is an array for each data type that
can exist for each of the two data sets. The array sizes are set to match the
configuration set for the module. If multiple MVI69-DNP modules are used within
a rack, a copy of this structure may have to be made to permit each module to
have its own database sizes. Ladder logic is required to transfer the data in this
structure between the module and the processor. Each data type has its own set
of unique block identification codes to distinguish the data contained in the read
or write block.
The structure of the object is shown in the following example:
DNP_BI INT[480] Number of DNP BI data words
DNP_BO INT[480] Number of DNP BO data words
DNP_Cntr DINT[240] Number of DNP counter double-words
DNP_AI INT[480] Number of DNP AI data words
DNP_FLTI REAL[240]
DNP_AO INT[480] Number of DNP AO data words
DNP_FLTO REAL[240]
IED_BI INT[480] Number of IED BI data words
IED_BO INT[480] Number of IED BO data words
IED_Cntr DINT[240] Number of IED counter double-wods
IED_AI INT[480] Number of IED AI data words
IED_AO INT[480] Number of IED AO data words

November 3, 2008
3.2 Special Objects

These objects utilize some of the advanced features the module provides. If your
application does not require the object, then you need not declare an instance of
the object. Each of the objects and associated function are discussed in the
following topics.
3.2.1 DNPCROB Object

The DNPCROB object is used in conjunction with the command control block
9901. This block sends a pulse output command to a single-point relay or a
trip/close relay. All the parameters required for each command to be used in the
block are contained in the object. Up to six of these objects can be contained in a
single block 9901 command. The structure of the object is shown in the following
example:
Port_Flag INT This field is ignored in the current implementation
Slave_ID INT This is the DNP slave address to send the command
to
Object INT This should always be 12
Variation INT This should always be 1
Function INT This should be 3, 5 or 6 depending on the write
method
Address INT This is the binary output starting point to operate in
the slave
Control_Code INT This determines the CROB operation
Pulse_Count INT This determines the number of pulses (0-255)
Pulse_On INT This determines the pulse on time
Pulse_Off INT This determines the pulse off time
3.2.2 DNPEventMsg Object

The DNPEventMsg object stores event messages received on the DNP master
port and passed to the processor. The structure of this object is shown in the
following example:
DevIndex INT Logical slave device index in module
IEDPoint INT Logical point address in IED database
DNPPoint INT Logical point address in DNP database
SlaveAddress INT Remote slave address that generated event
PointNum INT Point address in remote device
Object INT DNP object number for point
Variation INT DNP variation for event
LowTime INT Least-significant word of 48-bit DNP time
HighTime DINT Most-significant double-word of 48-bit DNP time
Value DINT Value for event
This information is passed to the processor from the module in a special read
block with an identification code of 9903. Each block can send up to 20 event
messages. Ladder logic must handle the receipt of this special data block and to
place the data received into controller tags.
November 3, 2008
3.2.3 DNPSlave_Err Object

The DNPSlave_Err object stores the slave status information returned from the
module after a 9949-block request from the ladder logic. An array of this object
should be defined to hold the status data for each slave used by the module. The
structure of the object is displayed in the following example:
Device_Index INT Index in the slave array for the master port
Slave_ID INT Slave address for device
Err_CRC INT Number of CRC errors
Err_Overflow INT Number of overflow errors
Err_Seq INT Number of sequence errors
Err_DLConf INT Number of data-link confirm retry errors
Err_DLCFail INT Number of data-link confirm failures
Err_AppResp INT Number of application response errors
3.2.4 DNP_BI_Event Object

The DNP_BI_Event object stores the information for a single binary input event
to be sent from the processor to the module in a command block 9958. The
structure shown contains all the parameters required for a binary input event.
EventCount INT Event Count
SeqCounter INT Sequence Counter
BinInptDataPt INT DNP Binary Input Data Point
MonDayState INT Month/Day/State
HourMin INT Hour/Minute
SecMilsec INT Second Millisecond
Year INT Year
Event2 INT[5] Event #2
3.2.5 DNP_AI_Event Object

The DNP_AI_Event object stores the information for a single analog input event
to be sent from the processor to the module in a command block 9959. The
structure shown contains all the parameters required for an analog input event.
EventCount INT Event Count
SeqCounter INT Sequence Counter
AIDataPt INT DNP Analog Input Data Point

November 3, 2008

AIvalue INT DNP Analog Input Value
MonDay INT Month/Day
HourMin INT Hour/Minute
SecMilsec INT Second Millisecond
Year INT Year
3.3 Adding the Module to an Existing CompactLogix Project
Important: The following steps describe how to install and configure the MVI69-DNP module with
RSLogix 5000 version 15 or older. If you are using RSLogix 5000 version 16, please refer to
Sample Add-On Instruction Import Procedure.
Important: The MVI69-DNP module has a power supply distance rating of 2 (L43 and L45
installations on first 2 slots of 1769 bus)
If you are installing and configuring the module with a CompactLogix processor,
follow these steps. If you are using a MicroLogix processor, refer to the next
section.
1 Add the MVI69-DNP module to the project. Right-click the mouse button on
the I/O Configuration option in the Controller Organization window to display
a pop-up menu. Select the New Module option from the I/O Configuration
menu.

November 3, 2008
This action opens the following dialog box:
2 Select the 1769-Module (Generic 1769 Module) from the list and click OK.
3 Enter the Name, Description and Slot options for your application, using the
values in the illustration above. You must select the Comm Format as Data -
INT in the dialog box, otherwise the module will not communicate over the
backplane of the CompactLogix rack.

November 3, 2008
Click OK to continue.
4 Select the Request Packet Interval value for scanning the I/O on the module.
This value represents the minimum frequency the module will handle
scheduled events. This value should not be set to less than 1 millisecond.
Values between 1 and 10 milliseconds should work with most applications.
5 Save the module. Click OK to dismiss the dialog box. The Controller
Organization window now displays the module's presence. The following
illustration shows the Controller Organization window:
6 Copy the Controller Tags from the sample program.

7 Copy the User Defined Data Types from the sample program.
8 Copy the Ladder Rungs from the sample program.
9 Save and Download the new application to the controller and place the
processor in run mode.

November 3, 2008
3.4 Adding the Module to an Existing MicroLogix Project

If you are installing and configuring the module with a MicroLogix processor,
follow these steps. If you are using a CompactLogix processor, refer to the
previous section.
This chapter describes how to install and configure the module to work with your
application. The configuration process consists of the following steps.
1 Use RSLogix to identify the module to the processor and add the module to a
project.
Note: The RSLogix software must be in "offline" mode to add the module to a project.
2 Modify the example ladder logic to meet the needs of your application, and
copy the ladder logic to the processor. Example ladder logic files are provided
on the CD-ROM.
Note: If you are installing this module in an existing application, you can copy the necessary
elements from the example ladder logic into your application.
The rest of this chapter describes these steps in more detail.

The first step in setting up the processor ladder file is to define the I/O type
module to the system. Start RSLogix 500, and follow these steps:
1 In RSLogix, open your existing application, or start a new application,
depending on your requirements.
2 Double-click the I/O Configuration icon located in the Controller folder in the
project tree. This action opens the I/O Configuration dialog box.
3 On the I/O Configuration dialog box, select "Other - Requires I/O Card Type
ID" at the bottom of the list in the right pane, and then double-click to open
the Module dialog box.

November 3, 2008
4 Enter the values shown in the following illustration to define the module
correctly for the MicroLogix processor, and then click OK to save your
configuration.
The input words and output words parameter will depend on the Block
Transfer Size parameter you specify in the configuration file. Use the values
from the following table.
Block Transfer Size Input Words Output Words
60 62 61
120 122 121
240 242 241
5 Click Next to continue.
6 After completing the module setup, the I/O configuration dialog box will
display the module's presence.
The last step is to add the ladder logic. If you are using the example ladder logic,
adjust the ladder to fit your application. Refer to the example Ladder Logic
section in this manual.
Download the new application to the controller and place the processor in run
mode. If you encounter errors, refer to Diagnostics and Troubleshooting (page
53) for information on how to connect to the module's Config/Debug port to use
its troubleshooting features.

November 3, 2008

November 3, 2008
Diagnostics and Troubleshooting MVI69-DNP ♦ CompactLogix or MicroLogix Platform
4 Diagnostics and Troubleshooting
In This Chapter
Reading Status Data from the Module .................................................. 53
LED Status Indicators............................................................................ 66
The module provides information on diagnostics and troubleshooting in the

following forms:
Status data values are transferred from the module to the processor.
Data contained in the module can be viewed through the
Configuration/Debug port attached to a terminal emulator.
LED status indicators on the front of the module provide information on the
module's status.
4.1 Reading Status Data from the Module

The MVI69-DNP module returns a Status Data block that can be used to
determine the module's operating status. This data is located in the module's
database at a user set location. For a complete listing of the status data object,
refer to the Reference chapter. The Configuration/Debug port provides the
following functionality:
Full view of the module's configuration data
View of the module's status data
Complete display of the module's internal database (registers 0 to 3999)
Version Information
Control over the module (warm boot, cold boot, transfer configuration)
Facility to upload and download the module's configuration file
4.1.1 The Configuration/Debug Menu

The Configuration and Debug menu for this module is arranged as a tree
structure, with the Main Menu at the top of the tree, and one or more sub-menus
for each menu command. The first menu you see when you connect to the
module is the Main menu.
Because this is a text-based menu system, you enter commands by typing the
command letter from your computer keyboard in the terminal application (for
example, HyperTerminal). The module does not respond to mouse movements
or clicks. The command executes as soon as you press the command letter —
you do not need to press [Enter]. When you type a command letter, a new
screen will be displayed in your terminal application.

November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Diagnostics and Troubleshooting
Navigation
All of the sub-menus for this module contain commands to redisplay the menu or
return to the previous menu. You can always return from a sub-menu to the next
higher menu by pressing [M] on your keyboard.
The organization of the menu structure is represented in simplified form in the
following illustration:
The remainder of this section shows you the menus available for this module,
and briefly discusses the commands available to you.
Keystrokes
The keyboard commands on these menus are almost always non-case sensitive.
You can enter most commands in lower case or capital letters.
The menus use a few special characters ([?], [-], [+], [@]) that must be entered
exactly as shown. Some of these characters will require you to use the [Shift],
[Ctrl] or [Alt] keys to enter them correctly. For example, on US English
keyboards, enter the [?] command as [Shift][/].
Also, take care to distinguish capital letter [I] from lower case letter [l] (L) and
number [1]; likewise for capital letter [O] and number [0]. Although these
characters look nearly the same on the screen, they perform different actions on
the module.
4.1.2 Required Hardware

You can connect directly from your computer's serial port to the serial port on the
module to view configuration information, perform maintenance, and send
(upload) or receive (download) configuration files.
ProSoft Technology recommends the following minimum hardware to connect
your computer to the module:
80486 based processor (Pentium preferred)
1 megabyte of memory
At least one UART hardware-based serial communications port available.
USB-based virtual UART systems (USB to serial port adapters) often do not
function reliably, especially during binary file transfers, such as when
uploading/downloading configuration files or module firmware upgrades.
A null modem serial cable.

November 3, 2008
4.1.3 Required Software

In order to send and receive data over the serial port (COM port) on your
computer to the module, you must use a communication program (terminal
emulator).
A simple communication program called HyperTerminal is pre-installed with
recent versions of Microsoft Windows operating systems. If you are connecting
from a machine running DOS, you must obtain and install a compatible
communication program. The following table lists communication programs that
have been tested by ProSoft Technology.
DOS ProComm, as well as several other terminal emulation programs
Windows 3.1 Terminal
Windows 95/98 HyperTerminal
Windows NT/2000/XP HyperTerminal
The module uses the Ymodem file transfer protocol to send (upload) and receive
(download) configuration files from your module. If you use a communication
program that is not on the list above, please be sure that it supports Ymodem file
transfers.
4.1.4 Using the Configuration/Debug Port

To connect to the module's Configuration/Debug port:
1 Connect your computer to the module's port using a null modem cable.
2 Start the communication program on your computer and configure the
communication parameters with the following settings:
Baud Rate 57,600
Parity None
Data Bits 8
Stop Bits 1
Software Handshaking None
3 Open the connection. When you are connected, press the [?] key on your
keyboard. If the system is set up properly, you will see a menu with the
module name followed by a list of letters and the commands associated with
them.
If there is no response from the module, follow these steps:
1 Verify that the null modem cable is connected properly between your
computer's serial port and the module. A regular serial cable will not work.
2 Verify that RSLinx is not controlling the COM port. Refer to Disabling the
RSLinx Driver for the Com Port on the PC (page 90).
3 Verify that your communication software is using the correct settings for baud
rate, parity and handshaking.
4 On computers with more than one serial port, verify that your communication
program is connected to the same port that is connected to the module.
If you are still not able to establish a connection, you can contact ProSoft
Technology Technical Support for further assistance.
November 3, 2008
4.1.5 Main Menu

When you first connect to the module from your computer, your terminal screen
will be blank. To activate the main menu, press the [?] key on your computer's
keyboard. If the module is connected properly, the following menu will appear on
your terminal screen:
Caution: Some of the commands available to you from this menu are designed for advanced
debugging and system testing only, and can cause the module to stop communicating with the
processor or with other devices, resulting in potential data loss or other failures. Only use these
commands if you are specifically directed to do so by ProSoft Technology Technical Support staff.
Some of these command keys are not listed on the menu, but are active nevertheless. Please be
careful when pressing keys so that you do not accidentally execute an unwanted command.
Setting the Debug Level

You can increase or decrease the level of debug messages sent from the module
to the Debug Menu. The following table shows the type of debugging information
for each key [0] to [9], [A] to [F]
Key None DNP Statistics Data Link Layer DPA Level
Messages Messages
0 X
1 X
2 X
3 X X
4
5 X
6 X
7 X X
8 X
9 X X
A X X
B X X X
C X

November 3, 2008
Key None DNP Statistics Data Link Layer DPA Level

Messages Messages
D X X
E X X
F X X X
Viewing the Error List

Press [L] to display the last 60 errors for the DNP slave port. Refer to the error
list section of the user manual to interpret each error recorded by the module.
If there are no errors present for the module, the message "NO ERRORS FOR
SYSTEM!" is displayed.
Viewing DNP Set Up & Pointers

Press [P] to display the memory allocation and the database setup parameters.
Viewing Operating Parameters

Press [O] to view the DNP Protocol setup information (Operating Parameters) for
the module.
Warm Booting the Module
Caution: Some of the commands available to you from this menu are designed for advanced
debugging and system testing only, and can cause the module to stop communicating with the
processor or with other devices, resulting in potential data loss or other failures. Only use these
commands if you are specifically directed to do so by ProSoft Technology Technical Support staff.
Some of these command keys are not listed on the menu, but are active nevertheless. Please be
careful when pressing keys so that you do not accidentally execute an unwanted command.
Press [R] from the Main Menu to warm boot (restart) the module. This command
will cause the program to exit and reload, refreshing configuration parameters
that must be set on program initialization. Only use this command if you must
force the module to re-boot.
Viewing Comm Stats

Press [S] to view the communication status for the DNP port.
Clearing the Error List

Press [W] to clear the error list. Use this command after viewing the error list
(page 57) to delete the current list of errors and start a new list.
Viewing COM States

Press [V] to view the current state of the DNP application port and the port
configuration information.

November 3, 2008
Viewing Master Port Slave Setup

Press [T] to view configuration information for the Master Port Slave.
Viewing Version Information

Press [G] to view Version information for the module.
Use this command to view the current version of the software for the module, as
well as other important values. You may be asked to provide this information
when calling for technical support on the product.
Values at the bottom of the display are important in determining module
operation. The Program Scan Counter value is incremented each time a
module's program cycle is complete.
Tip: Repeat this command at one-second intervals to determine the frequency of program
execution.
Opening the Class Assignment Menu

Press [Y] to view the class and deadband override values for the binary, analog,
float and double input DNP database.
Opening the DNP Database View Menu

Press [U] to open the DNP Database View Menu. This menu allows you to view
all data associated with the DNP Server driver. For more information about the
commands on this menu, refer to DNP Database View Menu (page 61).
Receiving the Configuration File

Press [<] (Shift Comma) to download (receive) the current configuration file from
the module. For more information on receiving and sending configuration files,
please see Uploading and Downloading the Configuration File (page 34).
Sending the Configuration File

Press [>] (Shift Period) to upload (send) an updated configuration file to the
module. For more information on receiving and sending configuration files,
please see Uploading and Downloading the Configuration File (page 34).
Viewing Block Transfer Statistics

Press [N] from the Main Menu to view the Block Transfer Statistics screen.
Use this command to display the configuration and statistics of the backplane
data transfer operations between the module and the processor. The information
on this screen can help determine if there are communication problems between
the processor and the module.
Tip: Repeat this command at one-second intervals to determine the number of blocks transferred
each second.

November 3, 2008
Opening the Command List Menu

Press [X] to open the Command List menu. Use this command to view the
configured command list for the module.
Opening the Command Error List Menu

Press [Z] to open the Command Error List. This list consists of multiple pages of
command list error/status data. Press [?] to view a list of commands available on
this menu.
4.1.6 The Class Assignment Menu

This menu allows you to view the class and deadband override values for the
binary, analog, float and double input DNP database. Press [?] to display the
commands available on this menu.
The following illustration shows the output for the Analog data set (menu key [1])

November 3, 2008
Viewing Binary Inputs

Press [0] to view the override values for Binary Input Data.
Viewing Analog Inputs

Press [1] to view the override values for Analog Input Data.
Viewing Float Inputs

Press [2] to view the override values for Float Input Data.
Viewing Double Inputs

Press [3] to view the override values for Double Input Data.
Redisplaying the Current Page

Press [S] to display the current page of data.
Viewing the Previous Page of Data

Press [P] to display the previous page of data.
Viewing the Next Page of Data

Press [N] to display the next page of data.
Returning to the Main Menu

Press [M] to return to the Main Menu.

November 3, 2008
4.1.7 DNP Database View Menu

Use this menu command to view the current contents of the selected database.
Press [?] to view a list of commands available on this menu.
Viewing Data Type Databases

Press [D] from the DNP menu, then hold down the [Shift] key and press the /
key.
Use the number keys 1 to 6 to select the display of the data type you wish to
view. For example, if the '1' key is pressed, the following is displayed:

November 3, 2008
Viewing Register Pages

To view sets of register pages, use the keys described below:
Command Description
[0] Display registers 0 to 99
And so on. The total number of register pages available to view depends on your
module's configuration.
Displaying the Current Page of Registers Again
This screen displays the current page of 100 registers in the database.
Moving Back Through 5 Pages of Registers

Press [-] from the Database View menu to skip back to the previous 500
registers of data.
Viewing the Previous 100 Registers of Data

Press [P] from the Database View menu to display the previous 100 registers of
data.
Skipping 500 Registers of Data

Hold down [Shift] and press [=] to skip forward to the next 500 registers of data.
Viewing the Next 100 Registers of Data

Press [N] from the Database View menu to select and display the next 100
registers of data.
Viewing Data in Decimal Format

Press [D] to display the data on the current page in decimal format.
Viewing Data in Hexadecimal Format

Press [H] to display the data on the current page in hexadecimal format.

November 3, 2008
Viewing Data in Floating Point Format

Press [F] from the Database View menu. Use this command to display the data
on the current page in floating point format. The program assumes that the
values are aligned on even register boundaries. If floating-point values are not
aligned as such, they are not displayed properly.
Viewing Data in ASCII (Text) Format

Press [A] to display the data on the current page in ASCII format. This is useful
for regions of the database that contain ASCII data.
Viewing Data in Double Word Decimal Format

Press [L] to display the data on the current page in Double Word Decimal format.
This is useful for regions of the database that contain Double Word Decimal data.
Viewing Data in Double Word Decimal Format

Press [X] to display the data on the current page in Double Word Hexadecimal
format. This is useful for regions of the database that contain Double Word
Hexadecimal data.
Viewing DNP Binary Inputs

Press [1] to view a list of DNP Binary Inputs.
Viewing DNP Binary Outputs

Press [2] to view a list of DNP Binary Outputs.
Viewing DNP Counters

Press [3] to view a list of DNP Counters.
Viewing DNP Analog Inputs

Press [4] to view a list of DNP Analog Inputs.
Viewing DNP Analog Outputs

Press [5] to view a list of DNP Analog Outputs.
Viewing DNP Frozen Counters

Press [6] to view a list of DNP Frozen Counters.
Viewing DNP Float Inputs

Press [7] to view a list of DNP Float Inputs.
Viewing DNP Float Outputs

Press [9] to view a list of DNP Float Outputs.
November 3, 2008

4.1.8 Master Command List Menu

Use this menu to view the command list for the module. Press [?] to view a list of
commands available on this menu.

Viewing the Previous 50 Commands

Press [-] to view the previous 50 commands.
Viewing the Previous Page of Commands

Press [P] to display the previous page of commands.
Viewing the Next 50 Commands

Press [+] to view the next 50 commands from the master command list.
Viewing the Next Page of Commands

Press [N] to display the next page of commands.


November 3, 2008
4.1.9 Master Command Error List Menu

Use this menu to view the command error list for the module. Press [?] to view a
list of commands available on this menu.

Viewing the Previous 20 Commands

Press [-] to display data for the previous 20 commands.
Viewing the Previous Page of Commands

Press [P] to display the previous page of commands.
Viewing the Next 20 Commands

Press [+] to display data for the next 20 commands.
Viewing the Next Page of Commands

Press [N] to display the next page of commands.


November 3, 2008
4.2 LED Status Indicators

The LEDs indicate the module's operating status as follows:
Module Color Status Indication
CFG Green On Data is being transferred between the module and a remote
terminal using the Configuration/Debug port.
Off No data is being transferred on the Configuration/Debug port.
P1 Green On Data is being sent/received on this port
Off Waiting for data on this port
P2 Green On Data is being sent/received on this port
Off Waiting for data on this port
APP Amber Off The MVI69-DNP is working normally.
On The MVI69-DNP module program has recognized a
communication error on one of its DNP ports.
BP Amber On The LED is on when the module is performing a write
operation on the backplane.
Off The LED is off when the module is performing a read
operation on the backplane. Under normal operation, the LED
should blink rapidly on and off.
OK Red/ Off The card is not receiving any power and is not securely
Green plugged into the rack.
Green The module is operating normally.
Red The program has detected an error or is being configured. If
the LED remains red for over 10 seconds, the program has
probably halted. Remove the card from the rack and re-insert
the card to restart the module's program.
BAT Red Off The battery voltage is OK and functioning.
On The battery voltage is low or battery is not present. Allow
battery to charge by keeping module plugged into rack for 24
hours. If BAT LED still does not go off, contact ProSoft
Technology, as this is not a user serviceable item.
If a configuration error is found for the client, the client configuration error word
will have a value other than zero. The configuration error word bits have the
following definitions:
Bit Description Value
0 0x0001
1 0x0002
2 0x0004
3 0x0008
4 Invalid retry count parameter 0x0010
5 The float flag parameter is not valid. 0x0020
6 The float start parameter is not valid. 0x0040
7 The float offset parameter is not valid. 0x0080
8 0x0100
9 0x0200
10 0x0400

November 3, 2008
Bit Description Value

11 0x0800
12 0x1000
13 0x2000
14 0x4000
15 0x8000
Correct any invalid data in the configuration for proper module operation. When
the configuration contains a valid parameter set, all the bits in the configuration
word will be clear. This does not indicate that the configuration is valid for the
user application. Make sure each parameter is set correctly for the specific
application.
If the APP, BP ACT and OK LEDs blink at a rate of every one-second, this
indicates a serious problem with the module. Call ProSoft Technology support to
arrange for repairs.
4.2.1 Clearing a Fault Condition

Typically, if the OK LED on the front of the module turns red for more than ten
seconds, a hardware problem has been detected in the module, or the program
has exited.
To clear the condition, follow these steps:
1 Turn off power to the rack
2 Remove the card from the rack
3 Verify that all jumpers are set correctly
4 If the module requires a Compact Flash card, verify that the card is installed
correctly
5 Re-insert the card in the rack and turn the power back on
6 Verify the configuration data being transferred to the module from the
CompactLogix or MicroLogix processor.
If the module's OK LED does not turn green, verify that the module is inserted
completely into the rack. If this does not cure the problem, contact ProSoft
Technology Support.

November 3, 2008
4.2.2 Troubleshooting
Use the following troubleshooting steps if you encounter problems when the
module is powered up. If these steps do not resolve your problem, please contact
ProSoft Technology Technical Support.
Processor Errors
Problem Description Steps to take
Processor Fault Verify that the module is plugged into the slot that has been configured for
the module.
Verify that the slot in the rack configuration has been set up correctly in the
ladder logic.
Processor I/O LED This indicates a problem with backplane communications. Verify that all
flashes modules in the rack are configured in the ladder logic.
Module has a power supply distance rating of 2 on Compact Logix. The
module must be within 2 slots of the power supply on Compact Logix, or that
the MicroLogix backplane can supply the 800ma required for the module.
Module Errors
Problem Description Steps to take
BP ACT LED remains This indicates that backplane transfer operations are failing. Connect to the
off or blinks slowly module's Configuration/Debug port to check this.
To establish backplane communications, verify the following items:
The processor is in Run mode.
The backplane driver is loaded in the module.
The module is configured for read and write block data transfer.
The ladder logic handles all read and write block situations.
The module is configured in the processor.
OK LED remains red The program has halted or a critical error has occurred. Connect to the
Configuration/Debug port to see if the module is running. If the program has
halted, turn off power to the rack, remove the card from the rack and re-
insert the card in the rack, and then restore power to the rack.

November 3, 2008
Reference MVI69-DNP ♦ CompactLogix or MicroLogix Platform
5 Reference
In This Chapter
Product Specifications ........................................................................... 69
Functional Overview.............................................................................. 72
Cable Connections ................................................................................ 89
Error Status Table ................................................................................. 95
Internal Indication Word....................................................................... 103
DNP V3.00 Device Profile Document .................................................. 104
DNP Subset Definition - Slave............................................................. 105
DNP Subset Definition - Master........................................................... 112
5.1 Product Specifications

The MVI69 DNP 3.0 module is a single slot, backplane compatible DNP 3.0
interface solution for the CompactLogix platform. This module provides highly
configurable support of both DNP 3.0 Master and Slave implementations (level 2
minimum), allowing the many SCADA and field devices supporting the DNP
protocol to be integrated into the powerful CompactLogix platform.
The module supports DNP Subset Level 2 features and some of the Level 3
features allowing the many SCADA and field devices supporting the DNP
protocol to be integrated into the CompactLogix platform. The module acts as an
input/output module between the DNP network and the CompactLogix processor.
The data transfer from the CompactLogix processor is asynchronous from the
actions on the DNP network. Databases are user defined and stored in the
module to hold the data required by the protocol.
5.1.1 General Specifications

Single Slot - 1769 backplane compatible
The module is recognized as an Input/Output module and has access to
processor memory for data transfer between processor and module
Ladder Logic is used for data transfer between module and processor.
Sample ladder file included.
Configuration data obtained from configuration text file downloaded to
module. Sample configuration file included.
Supports all CompactLogix processors: L20/L23/L30/L31/L32/L35, L43 and
L45 (L43 and L45 supported with RSLogix 5000 v16.03 or later)
Also supports MicroLogix 1500 LRP
November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Reference
5.1.2 Hardware Specifications

Specification Description
Dimensions Standard 1769 Single-slot module
Current Load 800 mA max@ 5 VDC
Power supply distance rating of 2 (L43 and L45
installations on first 2 slots of 1769 bus)
Operating Temp. 0 to 60°C (32 to 140°F)
Storage Temp. -40 to 85°C (-40 to 185°F)
Relative Humidity 5% to 95% (non-condensing)
LED Indicators Battery and Module Status
Application Status
Serial Port Activity
CFG Port Activity
CFG Port (CFG) RJ45 (DB-9F with supplied cable)
RS-232 only
No hardware handshaking
App Ports (P1,P2) (Serial modules) RS-232, RS-485 or RS-422 (jumper selectable)
RJ45 (DB-9F with supplied cable)
RS-232 handshaking configurable
500V Optical isolation from backplane
Shipped with Unit RJ45 to DB-9M cables for each port
6-foot RS-232 configuration Cable
5.1.3 Functional Specifications

The MVI69-DNP module supports the DNP 3.0 protocol with a minimum of Level
2 functionality. DNP protocol Subset Definitions for the Master and the Slave
drivers are available in the module's User Manual.
The module has two DNP protocol ports that can be user configured to operate in
a Master/Slave or in a Slave/Slave redundant port configuration.
User defined internal register space is accessible to the protocol driver and to the
CompactLogix processor memory.
Redundant Slave Port Operation

When configured in the Slave/Slave port configuration, the module's slave ports
operate in a primary and secondary fashion. In this mode, a single host polls the
module via redundant physical layer connections. Several methods are
supported to automatically switch between the primary and secondary slave
ports.

November 3, 2008
DNP 3.0 Slave Protocol Specifications

The DNP Slave port(s) accepts DNP commands to control and monitor data
stored in the module's DNP Slave databases. If a DNP Master port is also
configured, a portion of these slave databases can be derived from or can control
IED devices connected to the DNP master port.
Report-by-Exception data is logged to the module's database
Supports unsolicited messaging
Each DNP point type is user configurable by point
Class assignments are completely user-definable on a Type and point basis
(BI, AI, FI point types)
The analog inputs are class and deadband configurable on a point basis for
all formats (integer, float)
Supports clock synchronization from a master or from the processor
Support for four octet-strings are supported (object type 110) in the slave
driver to return version and other module information
Up to 400 events are stored for Analog Inputs (AI and FI) and 400 events for
Binary Inputs
In addition to the module generated events, AI and BI events can be
generated in the processor and transferred to the module (useful with
external timestamping hardware)
Configurable event buffer transmission threshold based on count and/or time
since last event transmission
Collision avoidance algorithm per DNP organization for redundant port
switching (redundant slave mode)
Special modem AT command string and timing support for dialing out on
redundant port (redundant slave mode)
DNP 3.0 Master Protocol Specifications

The DNP 3.0 Master port can be configured as a virtual DNP Master device that
actively issues user-defined DNP commands to nodes on the network.
The Master port supports 300 user defined commands, each one containing
its own set of data link and application layer characteristics
Master port logically supports up to 40 slave devices
Individual command configuration includes conditional or continuous polling
and Poll Delay Time
Slave status and Command status available for transfer to the processor
Event data received from the slave devices updates the module database
(Date and Time stamping is not stored or used by module)
Special command handling for Digital Output CROB under processor control
for pulse output control
Supports Report-by-Exception and Unsolicited Responses on a Time Interval
basis or on a user determined Event Count basis. Analog and Binary input
points are supported

November 3, 2008
5.2 Functional Overview

This section provides an overview of how the MVI69-DNP module transfers data
using the DNP protocol. You should understand the important concepts in this
chapter before you begin installing and configuring the module.
5.2.1 General Concepts

The following discussion explains several concepts that are important for
understanding the operation of the MVI69-DNP module.
Module Power Up
On power up the module begins performing the following logical functions:
1 Initialize hardware components.
o Initialize CompactLogix or MicroLogix backplane driver.
o Test and Clear all RAM.
o Initialize the serial communication ports.
o Initialize the TCP/IP stack and Ethernet interface.
2 Read module configuration from DNP.CFG file on Compact Flash disk or
Flash RAM (depending on hardware configuration).
3 Initialize the Module Register Space.
4 Enable Client and/or Server driver on selected ports, as configured.
When this initialization procedure is complete, the module will begin
communicating with other nodes on the network, depending on the configuration.
Main Logic Loop

Upon completing the power up configuration process, the module enters an
infinite loop that performs the following functions:

November 3, 2008
Backplane Data Transfer

The MVI69-DNP module communicates directly over the CompactLogix or
MicroLogix backplane. Data is paged between the module and the CompactLogix
processor across the backplane using the module's input and output images. The
update frequency of the images is determined by the scheduled scan rate
defined by the user for the module and the communication load on the module.
Typical updates are in the range of 2 to 10 milliseconds.
The data is paged between the processor and the module using input and output
image blocks.
This bi-directional transference of data is accomplished by the module filling in
data in the module's input image to send to the processor. Data in the input
image is placed in the Controller Tags in the processor by the ladder logic. The
input image for the module may be set to 62 words.
The processor inserts data to the module's output image to transfer to the
module. The module's program extracts the data and places it in the module's
internal database. The output image for the module may be set to 61 words.
The following illustration shows the data transfer method used to move data
between the CompactLogix processor, the MVI69-DNP module and the DNP
network.
All data transferred between the module and the processor over the backplane is
through the input and output images. Ladder logic must be written in the
CompactLogix processor to interface the block data with user data files. All data
used by the module is stored in its internal database. The following illustration
shows the layout of the database:

November 3, 2008
Data Area Blocks

DNP DATA BINARY INPUTS PLC DATA 0 to 7
IED DATA
BINARY OUTPUTS PLC DATA 8 to 15
IED DATA
COUNTER DATA PLC DATA 16 to 23
IED DATA
ANALOG INPUTS PLC DATA 24 to 31
IED DATA
ANALOG OUTPUTS PLC DATA 32 to 39
IED DATA
FLOAT INPUTS PLC DATA 80 to 87
DOUBLE INPUTS PLC DATA 88 to 95
FLOAT OUTPUTS PLC DATA 96 to 103
DOUBLE OUTPUTS PLC DATA 104 to 111
FROZEN COUNTER DATA
BINARY INPUT EVENTS
ANALOG INPUT EVENTS
FLOAT INPUT EVENTS
DOUBLE INPUT EVENTS
LAST VALUE DATA BINARY INPUTS
ANALOG INPUTS
FLOAT INPUTS
DOUBLE INPUTS
DNP BIN OUTPUTS
DNP ANAL OUTPUTS
IED BIN OUTPUTS
IED ANAL OUTPUTS
IED DATA BINARY INPUTS 40 to 47
BINARY OUTPUTS 48 to 55
COUNTER DATA 56 to 63
ANALOG INPUTS 64 to 71
ANALOG OUTPUTS 72 to 79
RBE FLAGS BINARY INPUT
ANALOG INPUT
Data contained in this database is paged through the input and output images by
coordination of the CompactLogix ladder logic and the MVI69-DNP module's
program. Up to 64 words of data can be transferred from the module to the
processor at a time. Up to 64 words of data can be transferred from the
processor to the module. The read and write block identification codes in each
data block determine the function to be performed or the content of the data
block. The module uses the following block numbers:

November 3, 2008
Block Number function/Description

-1 to -2 Dummy blocks: Used when too few blocks are to be transferred.
0 to 39, 80 to 111 DNP Data blocks
40 to 79 IED Data blocks
112 to 114 Error/Status and Error List Blocks
9901 CROB Control Block for Digital Outputs
9902 Command Control Block (Add command to Command List Queue)
9903 Event Messages from Master port
9949 Slave IED unit errors on master port
9950 Command List Error data
9958 PLC Binary Input Event data
9959 PLC Analog Input Event Data
9970 Set PLC time using module's DNP time
9971 Set module's time using PLC time
9998 Warm Boot Request from PLC (Block contains no data)
9999 Cold Boot Request from PLC (Block contains no data)
Blocks 0 to 54 transfer data. Block 112 transfers error/status data. Blocks 9901
to 9999 are used for command control of the module. Each block group is
described in the following topics.
Note: Block identification codes -1 and -2 are dummy blocks. The PLC should ignore any blocks
with these numbers as data does not represent any valid information in the module. The DNP
application will ignore any write blocks with these numbers.
5.2.2 Normal Data Transfer

Normal data transfer includes the paging of the user data found in the module's
internal database in registers 0 to 4999 and the status data. These data are
transferred through read (input image) and write (output image) blocks. The
structure and function of each block is discussed in the following topics.
The block transfer numbers are fixed in the program for each DNP data type for
this application. Block numbers are assigned by the application based on the
number of points of each type. The application only allocates the number of
blocks required to hold the data point count specified. For example, if 200 digital
input points are required for the application, only block 0 is allocated and if 150
counter points are required, blocks 16 to 20 are defined. These are separate data
areas for the DNP data used by the PLC and the data used by attached IED units
that are not part of the DNP database in the module. Each block transfers 60
word-size registers.
DATA TYPE START BLOCK # MAX BLOCK # MAX # OF POINTS
Digital Input 0 7 7680
Digital Output 8 15 7680
Counters 16 23 240
Analog Input 24 31 480
Analog Output 32 39 480

November 3, 2008
DATA TYPE START BLOCK # MAX BLOCK # MAX # OF POINTS

IED Digital Input 40 47 7680
IED Digital Output 48 55 7680
IED Counters 56 63 240
IED Analog Input 64 71 480
IED Analog Output 72 79 480
DNP Float Input 80 87 240
DNP Float Output 88 95 240
These blocks are mapped into a pre-defined memory area in the module.
Pointers into the memory area are computed by the application for each data
type. The application will only copy the portion of the block that contains valid
data.
Read Block
These blocks of data transfer information from the module to the CompactLogix
processor. The structure of the input image used to transfer this data is shown
below:
Offset Description
0 Read Block ID
1 Write Block ID
2 to 61 Read Data
The Read Block ID is an index value used to determine the location of where the
data will be placed in the CompactLogix processor controller tag array of module
read data. Each transfer can move up to 60 words (block offsets 0 to 61) of data.
The Write Block ID associated with the block requests data from the
CompactLogix processor. Under normal, program operation, the module
sequentially sends read blocks and requests write blocks. For example, if three
read and two write blocks are used with the application, the sequence will be as
follows:
R1W1 R2W2 R3W1 R1W2 R2W1 R3W2 R1W1

November 3, 2008
This sequence will continue until interrupted by other write block numbers sent by
the controller or by a command request from a node on the DNP network or
operator control through the module's Configuration/Debug port.
The following example shows a typical backplane communication application.
Write Block
These blocks of data transfer information from the CompactLogix or MicroLogix
processor to the module. The structure of the output image used to transfer this
data is shown below:
Offset Description
0 Write Block ID
1 to 60 Write Data
61 Spare
The Write Block ID is an index value used to determine the location in the
module's database where the data will be placed as defined in the table
presented in the previous section. Each transfer can move up to 60 words (block
offsets 1 to 60) of data.
5.2.3 Command Control Blocks

Command control blocks are special blocks used to control the module or
request special data from the module. The current version of the software
supports several command control blocks, each of which are discussed in the
following topics.
Block 9901 - Event Command

This block issues one or more command control requests to slaves attached to
the DNP master port for object 12 data. When the module receives a block 9901
identification code, it places the included commands into the command queue.
Block Format for Write
Word Offset in Block Data Field(s) Description
0 Block ID This field contains the block identification code of
9901 for the block.
1 Command Count This field defines the number of CROB blocks to
generate. The valid range for the field is 1 to 6.
2 to 11 Command #1 Data for the command relay block (CROB) to be
generated.
generated.
generated.
generated.
generated.
generated.

November 3, 2008
The following fields are used for each 10-word record in the command list:
Word Offset Definitions Description
0 Port/Flags This field is currently ignored as all 9901 blocks
are sent immediately out the master port.
1 Slave Address This is the IED node address for the slave to
consider on the network.
2 Object Object type always 12
3 Variation Variation always 1
4 Function Function codes 3, 5 and 6 supported. Function
code 4 is automatically sent after a successful
function 3.
5 Address in Slave Point in IED to consider with the CROB.
6 Control Code This is a standard DNP protocol control code byte
(see description below).
7 Pulse Count This parameter specifies the number of pulses to
generate for pulse output control. This parameter
has a range of 0 to 255 as the value is a byte
parameter in the CROB. If a value of zero is
entered, the operation will not execute.
8 Pulse On Time This parameter specifies the on-time interval for
pulse control.
9 Pulse Off Time This parameter specifies the off-time interval for
pulse control.
The control code in the command is a bit coded byte value with the following
definition:
Bits Definitions Description
0 to 3 Code These bits determine the control operation to be
performed by the command: 0=No operation,
1=Pulse on, 2=Pulse off, 3=Latch on and 4=Latch
off. All other values are undefined in the DNP
protocol.
4 Queue 0=Normal (execute once), 1=Requeue (place at
end of queue after operation).
5 Clear This parameter clears the queue. If the value is
set to zero, the queue is not affected. If the value
is set to 1, the queue will be cleared.
6 to 7 Trip/Close These two bits select the trip or close relay. For
close relay control, set the bits to 01. For trip
relay control, set the bits to 10. A value of 00 for
the bits is used for single point control of normal
digital output points.
Block Format for Read

0 Block ID This field contains the block identification code
of 9901 for the block.
1 Next write block ID This field contains the ID number of the next
number write block.

November 3, 2008
Block 9902 - Command Control Block

The 9902 identification code is used by the PLC to send a list of commands to be
placed in the command queue. Commands placed in the queue with this method
need not have their enable bit set. The format of the block is as follows:
0 Block ID This field contains the value of 9902 identifying
the enable command to the module.
1 Command count This field contains the number of commands to
enable in the command list. Valid values for this
field are 1 to 60.
2 to 61 Command Numbers to These 60 words of data contain the command
enable numbers in the command list to enable. The
commands in the list will be placed in the
command queue for immediate processing by
the module. The first command in the list has an
index of 0.
There is no response to this block by the module. The module will place the
selected commands in the command queue. If the command references a IED
unit that is not in the slave list, the command will not be placed in the command
queue. Normal processing of the command list will continue after the commands
specified in this block are processed.
the enable command to the module.
1
2 Number of commands This is the number of commands added to the
added command queue in the last 9902 block.
Block 9903 - Event Message Block

If the module contains a DNP master port and it is configured to pass event
messages from the port to the processor, block identification code 9903 is used.
When the master port receives an event message, it will place the data in the
message into the event message queue. When the backplane task in the module
recognizes data in this queue, it forms 9903 blocks to transfer the data to the
processor. Ladder Logic extracts the event data from the 9903 block and place it
in controller tags. The format of the block is as follows:
9903 for the block.
1 Block ID This is the next block requested by the module.
2 Event Count This field contains the number of events present
in the block. Values of 1 to 4 are valid.

November 3, 2008

3 to 14 Event 1 Event message
51 to 61 Spare Not used
The format of each 12-word data region in the block is as follows:
Word Offset Definitions Description
0 Device Index This field contains the module's device index for
the IED the message was received from (0 to
39).
1 IED Address This field contains the IED database index for the
point. If set to -1, then not in database.
2 DNP Address This field contains the DNP database index for
the point. If set to -1, then not in database.
3 Slave Address This field contains the remote slave address for
the IED unit from which the message was
received.
4 Point Number This field contains the point number in the
remote IED unit for the event message.
5 Object This field contains the object code for the point
and event.
6 Variation This field contains the variation code for the point
and event.
7 Low Time This field contains the least-significant word of
the 48-bit DNP time for the event.
8 to 9 High Time This field contains the most-significant double
word of the 48-bit time for the event.
10 to 11 Value This field contains the a double word value for
the point associated with the event message.
Block 9949 - Read Slave Communication Error Table

If the processor sends a block 9949, the module will respond with a slave
communication error listing. The following example shows the format of the
block:
the block type to the module.
1 Number of slaves This field contains the number of slaves to report
in the response message. The value has a range
of 1 to 7.
2 Start Slave Index This parameter sets the index in the slave array
where to start. The first slave in the array has a
value of 0. The last index in the array has a value
of MaxSlaves -1.
3 to 61 Spare Not Used

November 3, 2008
The module responds to a valid request with a block 9949 containing the
requested slave information. The following example shows the format of the
block:
the block type to the PLC.
2 Slave Count This field contains the number of slave records
contained in the block that must be processed by
the PLC. This field will have a value of 1 to 7.
3 Slave Start Index This field contains the index in the slave array for
the first record in the file. This field will have a
value of 0 to MaxSlaves-1.
4 to 11 Slave Data #1 This is the slave data for the first slave in the
block. The slave index for the data is the Slave
Start Index given in word 3.
12 to 19 Slave Data #2 This is the slave data for the second slave in the
block.
20 to 27 Slave Data #3 This is the slave data for the third slave in the
block.
block.
block.
block.
block.
Block 9950 - Read Command Error List

If the processor sends a block number of 9950 to the module, the application
responds with a command error list. Each command in the system has a data
word set aside for its last error code. The value is set by the DNP master port
command list task and the values correspond to the error section of this manual.
The format of the block is shown below:
1 Number of Commands This field contains the number of commands to
to report report in the response message. The value has a
range of 1 to 58.
2 Start Index of First This parameter sets the index in the command
Command list where to start. The first command in the list
has a value of 0. The last index in the list has a
value of MaxCommands -1.

November 3, 2008
The module responds to a valid request with a block containing the requested
error information. The format of the block is shown in the following example:
the block type to the PLC.
2 Number of Commands This field contains the number of commands
reported contained in the block that must be processed
by the PLC. This field will have a value of 1 to
58.
3 Start Index of First This field contains the index in the command list
Command for the first value in the file. This field will have a
value of 0 to MaxCommands-1.
4 to 61 Command List Errors Each word of this area contains the last error
value recorded for the command. The command
index of the first value (offset 4) is specified in
word 3 of the block. The number of valid
command errors in the block is set in word 2 of
the block. Refer to the command error list to
interpret the error codes reported.
Block 9958 - Processor Binary Input Event

If the processor sends a block 9958, the module will place the binary input event
data in the block into the event buffer and alter the data values for the points in
the DNP binary input database. The format for the message is shown in the
following table.
the event block to the module.
1 Event Count This field contains the number of events
contained in the block. Valid values for this field
are 1 to 11.
2 Sequence Counter This field holds the sequence counter for each
9958 block transfer. This synchronizes and
confirms receipt of the block by the module.
3 DNP Binary Input Data This is the data point in the DNP binary input
point database represented by the event.
4 Month/Day/State Formatted: bits 0 to 4 = Day, bits 8 to 11 =
Month, bit 15 = digital state for point. All other
bits are ignored.
5 Hour/Minute Formatted: bits 0 to 5 = Minutes, bits 8 to 12 =
Hour. All other bits are ignored.
6 Sec/Millisecond Formatted: bits 0 to 9 = Milliseconds, bits 10 to
15 = Seconds.
7 Year This is the four digit year for the event.
8 to 12 Five words of data for Event #2.

November 3, 2008

To ensure the receipt of this block of information, the module returns a block
9958 with the sequence counter set to the value of the last successful block 9958
received.
0 Block ID Identification code for block set to 9958.
1 Block ID Block identification code for request from PLC by
the module.
processed by the module.
3 Sequence Counter This field contains the sequence counter of the
last successful block 9958 received.
Block 9959 - Processor Analog Input Event

If the processor sends a block 9959, the module will place the analog input event
data in the block into the event buffer and alter the data values for the points in
the DNP analog input database. The format for the event message is shown in
the event block to the module.
contained in the block. Valid values for this field
are 1 to 9.
2 Sequence Counter This field holds the sequence counter for each
9959 block transfer. This synchronizes and
confirms receipt of the block by the module.
3 DNP Analog Input Data This is the data point in the DNP analog input
point database represented by the event.
4 Analog Input Value This is the new analog input value represented
in the event.

November 3, 2008

5 Month/Day Formatted: bits 0 to 4 = Day, bits 8 to 11 =
Month. All other bits are ignored.
6 Hour/Minute Formatted: bits 0 to 5 = Minutes, bits 8 to 12 =
Hour. All other bits are ignored.
7 Sec/Millisecond Formatted: bits 0 to 9 = Milliseconds, bits 10 to
15 = Seconds.
8 Year Four digit year value for event.
9 to 14 Six words of data for Event #2.
To ensure the receipt of this block of information, the module returns a block
9959 with the sequence counter set to the value of the last successful block 9959
received.
0 Block ID Identification code for block set to 9959.
1 Block ID Block identification code for request from PLC by
the module.
processed by the module.
3 Sequence Counter This field contains the sequence counter of the
last successful block 9959 received.
Block 9970 - Set Processor Time Using Module Time

This block transfers the module's time to the processor. Ladder logic must be
used to set the processor's clock using the data received. The format of the block
sent from the processor has the following format:
1 to 61 Not Used Not Used
The module will respond to a valid block 9970 request with a block containing the
requested date and time. The following example shows the format of this block.

November 3, 2008

0 Block Read ID This field contains the block identification code of
9970 for the block.
1 Block Write ID This is the next block requested by the module.
2 Year This field contains the four-digit year to be used
with the new time value.
3 Month This field contains the month value for the new
time. Valid entry for this field is in the range of 1
to 12.
4 Day This field contains the day value for the new
to 31.
5 Hour This field contains the hour value for the new
to 23.
6 Minute This field contains the minute value for the new
to 59.
7 Seconds This field contains the second value for the new
to 59.
8 Milliseconds This field contains the millisecond value for the
new time. Valid entry for this field is in the range
of 0 to 999.
9 Remote Time This field informs the PLC if the date and time
Synchronization passed has been synchronized with a remote
DNP master device on the module's slave port.
Block 9971 - Set Module's Time Using the Processor's Time

This block sets the clock in the module to match the clock in the processor. If the
processor sends a block 9971, the module will set its time using the data
contained in the block. The format of the block is shown in the following table.
9971 for the block.
1 Year This field contains the four-digit year to be used
with the new time value.
2 Month This field contains the month value for the new
to 12.
3 Day This field contains the day value for the new
to 31.
4 Hour This field contains the hour value for the new
to 23.

November 3, 2008

5 Minute This field contains the minute value for the new
to 59.
6 Seconds This field contains the second value for the new
to 59.
7 Milliseconds This field contains the millisecond value for the
new time. Valid entry for this field is in the range
of 0 to 999.
Warm Boot
This block is sent from the CompactLogix or MicroLogix processor to the module
(output image) when the module is required to perform a warm-boot (software
reset) operation. This block is commonly sent to the module any time
configuration data modifications are made in the controller tags data area. This
will force the module to read the new configuration information and to restart. The
structure of the control block is shown below:
Offset Description Length
0 9998 1
1 to 63 Spare 63
Cold Boot
This block is sent from the CompactLogix processor to the module (output
image) when the module is required to perform the cold boot (hardware reset)
operation. This block is sent to the module when a hardware problem is detected
by the ladder logic that requires a hardware reset. The structure of the control
block is shown in the following table.
Offset Description Length
0 9999 1
1 to 63 Spare 63

November 3, 2008
5.2.4 Data Flow between MVI69-DNP Module and CompactLogix

Processor
The following topics describe the flow of data between the two pieces of
hardware (CompactLogix processor and MVI69-DNP module) and other nodes
on the DNP network under the module's different operating modes. Each port on
the module is configured to emulate a DNP master device or a DNP slave
device. The operation of each port is dependent on this configuration.
The following topics discuss the operation of these drivers.
Slave Driver
The Slave Driver mode allows the MVI69-DNP module to respond to data read
and write commands issued by a Master on the DNP network. The following flow
chart and associated table describe the flow of data into and out of the module.
Step Description
1 The slave port driver receives the configuration information from the configuration file.
This information configures the serial port and define the slave node characteristics.
Additionally, the configuration information contains data that can be used to offset data in
the database to addresses requested in messages received from master units.
2 A host device (DNP Master Unit) issues a read or write command to the module's node
address. The port driver qualifies the message before accepting it into the module.
3 After the module accepts the command, the data is immediately transferred to or from
the internal database in the module. If the command is a read command, the data is read
out of the database and a response message is built. If the command is a write
command, the data is written directly into the database and a response message is built.
4 After the data processing has been completed in Step 3, the response is issued to the
originating master node.
5 Counters are available in the Status Block that permit the ladder logic program to
determine the level of activity of the Slave Driver.

November 3, 2008
Review the Installing and Configuring the Module section for a complete list of
parameters that must be defined for a slave port. The response messages from
the slave driver include an IIN (internal indication word) defined in the Reference
chapter - Internal Indication Word.
The slave driver supports Object 110 (octet string data). Four points are pre-
assigned values as shown in the following table.
OCTET STRING POINT LIST
Point # Description
0 Module Name as assigned in configuration file.
1 Product Name
2 Version Information in format:
wwww xxxx yyyy zzzz
Where wwww is product code, xxxx is the revision, yyyy is the operating
system number and zzzz is the run number.
3 Manufacturer name for module.
Master Driver Mode

In the Master mode, the MVI69-DNP module is responsible for issuing read or
write commands to slave devices on the DNP network. These commands are
user-configured in the module via the Master Command List received from the
processor or issued directly from the processor (command control). Command
status is returned to the processor for each individual command in the command
list status block. The following flow chart and associated table describe the flow
of data into and out of the module.

November 3, 2008
Step Description
1 The Master driver obtains configuration data from the configuration file. The configuration
data obtained includes the Master Slave and Command Lists. These values are used by
the Master driver to determine the type of commands to be issued to other nodes on the
DNP network.
2 After configuration, the Master driver begins transmitting read and/or write commands to
the other nodes on the network. If writing data to another node, the data for the write
command is obtained from the module's internal database to build the command.
3 Presuming successful processing by the node specified in the command, a response
message is received into the Master driver for processing.
4 Data received from the node on the network is passed into the module's internal
database, assuming a read command.
5 Status data is returned to the CompactLogix processor for each command in the Master
Command List.
Refer to the Installing and Configuring the Module section for a complete
description of the parameters required to define the virtual DNP Master port.
5.3 Cable Connections

The application ports on the MVI69-DNP module support RS-232, RS-422, and
RS-485 interfaces. Please inspect the module to ensure that the jumpers are set
correctly to correspond with the type of interface you are using.
Note: When using RS-232 with radio modem applications, some radios or modems require
hardware handshaking (control and monitoring of modem signal lines). Enable this in the
configuration of the module by setting the UseCTS parameter to 1.
5.3.1 RS-232 Configuration/Debug Port

This port is physically an RJ45 connection. An RJ45 to DB-9 adapter cable is
included with the module. This port permits a PC based terminal emulation
program to view configuration and status data in the module and to control the
module. The cable for communications on this port is shown in the following
diagram:

November 3, 2008
Disabling the RSLinx Driver for the Com Port on the PC

The communication port driver in RSLinx can occasionally prevent other
applications from using the PC's COM port. If you are not able to connect to the
module's configuration/debug port using ProSoft Configuration Builder (PCB),
HyperTerminal or another terminal emulator, follow these steps to disable the
RSLinx Driver.
1 Open RSLinx and go to Communications>RSWho
2 Make sure that you are not actively browsing using the driver that you wish to
stop. The following shows an actively browsed network:
3 Notice how the DF1 driver is opened, and the driver is looking for a processor
on node 1. If the network is being browsed, then you will not be able to stop
this driver. To stop the driver your RSWho screen should look like this:
Branches are displayed or hidden by clicking on the or the icons.
4 When you have verified that the driver is not being browsed, go to
Communications>Configure Drivers
You may see something like this:

November 3, 2008
If you see the status as running, you will not be able to use this com port for
anything other than communication to the processor. To stop the driver press
the "Stop" on the side of the window:
5 After you have stopped the driver you will see the following:
6 Upon seeing this, you may now use that com port to connect to the debug
port of the module.
Note: You may need to shut down and restart your PC before it will allow you to stop the driver
(usually only on Windows NT machines). If you have followed all of the above steps, and it will not
stop the driver, then make sure you do not have RSLogix open. If RSLogix is not open, and you
still cannot stop the driver, then reboot your PC.
5.3.2 RS-232
When the RS-232 interface is selected, the use of hardware handshaking
(control and monitoring of modem signal lines) is user definable. If no hardware
handshaking will be used, the cable to connect to the port is as shown below:

November 3, 2008
RS-232: Modem Connection

This type of connection is required between the module and a modem or other
communication device.
The "Use CTS Line" parameter for the port configuration should be set to 'Y' for
most modem applications.
RS-232: Null Modem Connection (Hardware Handshaking)

This type of connection is used when the device connected to the module
requires hardware handshaking (control and monitoring of modem signal lines).

November 3, 2008
RS-232: Null Modem Connection (No Hardware Handshaking)

This type of connection can be used to connect the module to a computer or field
device communication port.
Note: If the port is configured with the "Use CTS Line" set to 'Y', then a jumper is required between
the RTS and the CTS line on the module connection.
5.3.3 RS-422

November 3, 2008
5.3.4 RS-485
The RS-485 interface requires a single two or three wire cable. The Common
connection is optional and dependent on the RS-485 network. The cable required
for this interface is shown below:
Note: Terminating resistors are generally not required on the RS-485 network, unless you are
experiencing communication problems that can be attributed to signal echoes or reflections. In this
case, install a 120 ohm terminating resistor on the RS-485 line.
RS-485 and RS-422 Tip

If communication in the RS-422/RS-485 mode does not work at first, despite all
attempts, try switching termination polarities. Some manufacturers interpret +/-
and A/B polarities differently.
5.3.5 DB9 to RJ45 Adaptor (Cable 14)

November 3, 2008
5.4 Error Status Table

The program maintains an error status table. You can use the error/status data to
determine the "health" of the module.
The data in the block is structured as follows:
Word Block Variable Name Description
Offset
0 2 Current DNP Slave Port This value represents the current value of the
status error code for the port. This value will only be
valid if the port is configured as a slave. The
possible values are described in the application
documentation.
1 3 DNP Slave Port last This value represents the last error code
transmitted error code transmitted to the master by this slave port.
2 4 DNP Slave Port total This value represents the total number of
number of message message frames that have matched this slaves
frames received by slave address on this port. This count includes
message frames which the slave may or may
not be able to parse and respond.
3 5 DNP Slave Port total This value represents the number of good (non-
number of response error) responses that the slave has sent to the
message frames sent master on this port. The presumption is that if
from slave the slave is responding, the message was
good. Note: This is a frame count.
4 6 DNP Slave Port total This value represents the total number of
number of message message frames received by the slave,
frames seen by slave regardless of the slave address.
5 7 DNP Slave This value counts the number of times a sync
synchronization error error occurs. The error occurs when extra bytes
count (Physical Layer are received before the start bytes (0x05 and
Error) 0x64) are received.
6 8 DNP Slave overrun error This value counts the number of times the
count (Physical Layer overrun error occurs. This error occurs when
Error) the mainline Data Link Layer routine cannot
read the data received on the communication
port before it is overwritten.
7 9 DNP Slave length error This value counts the number of times an
count (Physical Layer invalid length byte is received. If the length of
Error) the message does not match the length value
in the message, this error occurs.
8 10 DNP Slave bad CRC This value counts the number of times a bad
error (Data Link Layer CRC value is received in a message.
Error)
9 11 DNP Slave user data This value counts the number of times the
overflow error (Transport application layer receives a message fragment
Layer Error) buffer which is too small.
10 12 DNP Slave sequence This value counts the number of times the
error (Transport Layer sequence numbers of multi-frame request
Error) fragments do not increment correctly.
11 13 DNP Slave address error This value counts the number of times the
(Transport Layer Error) source addresses contained in a multi-frame
request fragments do not match.

November 3, 2008

Offset
12 14 DNP Slave Binary Input This value contains the total number of binary
Event count input events which have occurred.
13 15 DNP Slave Binary Input This value represents the number of binary
Event count in buffer input events which are waiting to be sent to the
master.
14 16 DNP Slave Analog Input This value contains the total number of analog
Event count input events which have occurred.
15 17 DNP Slave Analog Input This value represents the number of analog
Event count in buffer input events which are waiting to be sent to the
master.
16 18 DNP Slave bad function This value counts the number of times a bad
code error (Application function code for a selected object/variation is
Layer Error) received by the slave device.
17 19 DNP Slave object This value counts the number of times a
unknown error request for an unsupported object is received
(Application Layer Error) by the slave device.
18 20 DNP Slave out of range This value counts the number of times a
error (Application Layer parameter in the qualifier, range or data field is
Error) not valid or out of range.
19 21 DNP Slave message This value counts the number of times an
overflow error application response message from the slave is
(Application Layer Error) too long to transmit.
20 22 DNP Slave multi-frame This value counts the number of times the
message from DNP slave receives a multi-frame message from the
Master error (Application master. The application does not support multi-
Layer Error) frame master messages.
21 23 Total blocks transferred Total BTR/BTW or side-connect interface
transfers attempted by the module.
22 24 Successful blocks This value represents the total number of
transferred transfer operations between the CompactLogix
processor and module that are successful.
23 25 Total errors in block Total number of transfers that resulted in an
transfer error condition.
24 26 Total BTR or write errors Total number of BTR or write transfers that
resulted in an error.
25 27 Total BTW or read errors Total number of BTW or read transfers that
resulted in an error.
26 28 Block number error Number of BTW requests that resulted in an
incorrect BTW identification code.
27 29 Continuous block error Count of sequential data transfer errors. When
counter this value exceeds that specified for the data
transfer operation, the error flag below will be
set.
28 30 Reserved Not used
29 31 Configuration Type This is a coded field that defines the
configuration of the module. The codes are as
follows: 0=Single Slave Configuration, 1=Dual
Slave Configuration, 2=Slave/Master
Configuration

November 3, 2008

Offset
30 to 31 32 to 33 Product Name (ASCII) These two words contain the product name of
the module in ASCII format.
32 to 33 34 to 35 Revision (ASCII) These two words contain the product revision
level of the firmware in ASCII format.
34 to 35 36 to 37 Operating System These two words contain the module's internal
Revision (ASCII) operating system revision level in ASCII format.
36 to 37 38 to 39 Production Run Number These two words contain the production 'batch'
(ASCII) number for the particular chip in the module in
ASCII format.
38 40 DNP Master Port Slave This is the total number of slaves configured for
Count the DNP Master port. This may not represent
the number of active slaves as it includes
slaves that are not enabled.
39 41 DNP Master Port This is the total number of commands
Command Count configured for the DNP Master port. This may
not represent the number of active commands
as it includes commands that are disabled.
40 42 DNP Master Port Device This value represents the number of memory
Memory Block Count allocation blocks for slave devices. This
number should be one greater than the number
of slave devices. The extra device is held for
the broadcast device.
41 43 DNP Master Port Frame This value represents the number of physical
Block Count layer frame memory allocation blocks used by
the program.
42 44 DNP Master Port Data This value represents the number of receive
Link Receive Block data link layer memory blocks allocated.
Count
43 45 DNP Master Port Data This value represents the number of transmit
Link Transmit Block data link layer memory blocks allocated.
Count
44 46 DNP Master Port This value represents the number of application
Application Layer layer receive memory blocks allocated.
Receive Block Count
45 47 DNP Master Port This value represents the number of application
Application Layer layer transmit memory blocks allocated.
Receive Block Count
46 48 DNP Master Port Device This value represents the number of memory
Memory Allocation Error allocation errors for device blocks.
Count
47 49 DNP Master Port This value represents the number of memory
Physical Layer Memory allocation errors for physical layer frame blocks.
Allocation Error Count
48 50 DNP Master Port Data This value represents the number of memory
Link Layer Receive allocation errors for data link layer receive
Memory Allocation Error blocks.
Count
49 51 DNP Master Port Data This value represents the number of memory
Link Layer Transmit allocation errors for data link layer transmit
Memory Allocation Error blocks.
Count

November 3, 2008

Offset
Application Layer allocation errors for application layer receive
Receive Memory blocks.
Application Layer allocation errors for application layer transmit
Transmit Memory blocks.
52 54 DNP Master This value counts the number of times a sync
Synchronization Error error occurs. The error occurs when extra bytes
Count (Physical Layer are received before the start bytes (0x05 and
Error) 0x64) are received.
53 55 DNP Master Length Error This value counts the number of times an
Count (Physical Layer invalid length byte is received. If the length of
Error) the message does not match the length value
in the message, this error occurs.
54 56 DNP Master Bad CRC This value counts the number of times a bad
Error Count (Physical CRC value is received in a message.
Layer Error)
55 57 Scan Counter LSB Program scan counter
56 58 Scan Counter MSB
57 59 Free Memory LSB Free memory in module
58 60 Free Memory MSB
59 61 DNP Slave Port Transmit Value of the DNP Slave state machine for
State transmit.
60 62 DNP Float Event Count Total number of events generated for analog
floating-point input data points.
61 63 DNP Double Event Total number of events generated for analog
Count double, floating-point input data points.
62 64 Event Message Queue Number of event messages waiting to send to
Count processor.
63 65 Event Message Queue Flag to indicate if the event message queue
Overflow has overflowed. If more than 200 event
messages are received on the master port and
they are not sent to the processor, this flag will
be set (1). The flag will clear after the
messages are sent to the processor.
64 to 77 66 to 79 Reserved Future Use
78 80 Error_List[0] First value in error list
79 81 Error_List[1] Second value in error list
- - - -
137 139 Error_List[59] Last value in error list

November 3, 2008
5.4.1 Module Error Codes

If the module's program encounters an error during execution, it will log the error
to the error list. This list is transferred to the CompactLogix processor using block
identification code 100 (see section above) in at offsets 62 to 119. This data is
also available for viewing on the debug monitor port. The following tables list the
error codes generated by the program with their associated description. Use the
errors to help define where problems exist in the system.
Slave Port Communication Errors

Error Name Description
Code
0 OK The module is operating correctly and there are no errors.
10 DNP synchronization Extra bytes are received before the start bytes (0x05 and
error (Physical Layer 0x64).
Error)
11 DNP overrun error Mainline Data Link Layer routine could not read data
(Physical Layer Error) received on DNP port before it was overwritten.
12 DNP length error Length of message does not match length value in message.
(Physical Layer Error)
13 DNP bad CRC error Computed CRC value for message does not match that
(Data Link Layer Error) received in message.
14 DNP user data overflow Application layer received a message fragment buffer which
error (Transport Layer is too small.
Error)
15 DNP sequence error Sequence numbers of multi-frame request fragments do not
(Transport Layer Error) increment correctly.
16 DNP address error Source addresses contained in multi-frame request
(Transport Layer Error) fragments do not match.
17 DNP bad function code Function code received from DNP master is not supported
error (Application Layer for selected object/variation.
Error)
18 DNP object unknown Slave does not have the specified objects or there are no
error (Application Layer objects assigned to the requested class.
Error)
19 DNP out of range error Qualifier, range or data fields are not valid or out of range for
(Application Layer the selected object/variation.
Error)
20 DNP message overflow Application response buffer overflow condition. The response
error (Application Layer message from the slave is too long to transmit.
Error)
21 DNP master multi-frame Received a multi-frame message from the DNP master. This
message error application does not support multi-frame messages from the
(Application Layer master.
Error)

November 3, 2008
System Configuration Errors

Code
100 Too many binary input Too many binary input points are configured for the module.
points Maximum value is 7680
101 Too many binary output Too many binary output points are configured for the module.
102 Too many counter Too many counter points are configured for the module.
103 Too many analog input Too many analog input points are configured for the module.
104 Too many analog input Too many analog output points are configured for the
points module. Maximum value is 480
105 Too many binary input Too many binary input events are configured for the module.
events Maximum value is 400.
106 Too many analog input Too many analog input events are configured for the module.
events Maximum value is 400.
107 Invalid analog input Deadband value for analog input events is out of range.
deadband Value must be in the range of 0 to 32767.
108 Not enough memory There is not enough memory in the module to configure the
module as specified.
109 Invalid block transfer Block transfer delay value specified is too low.
delay for blocks
error/status blocks
110 File count invalid The file count must be in the range of 0 to 6.
111 Invalid file record size The file record size must be in the range of 1 to 120.
112 Invalid block The file block transfer code must be in the range of 100 to
identification code for 120.
file
DNP Port Configuration Errors

Code
212 Invalid DNP address The DNP address specified in the configuration is not valid (0
to 65534).
213 Invalid DNP port baud The baud rate code specified in the configuration is not valid.
rate
219 Invalid DNP data link The data link confirmation mode code is not valid in the
layer confirm mode configuration.
220 Invalid DNP data link The data link time-out period specified in the configuration is
confirm time-out 0. It must be an integer in the range of 1 to 65535.
222 Invalid DNP The select/operate arm timer is set to 0. It must be an integer
select/operate arm time in the range of 1 to 65535.
duration
223 Invalid DNP application The application layer confirm time-out value is set to 0. It
layer confirm time-out must be an integer in the range of 1 to 65535.
224 Invalid DNP write time The write time interval is not in the data range in the
interval configuration. The value must be in the range of 0 to 1440.

November 3, 2008

Code
225 Invalid DNP unsolicited The unsolicited response mode code is not valid in the
response mode configuration.
226 Invalid DNP unsolicited The unsolicited response minimum quantity for Class 1 is not
response minimum valid in the configuration. Value must be an integer in the
quantity for Class 1 range of 1 to 255.
230 Invalid DNP unsolicited The unsolicited response destination address is not valid in
response destination the configuration. Value must be in the range of 1 to 65534.
address
Command Error Codes

General Command Errors
Code
1 Device not defined The IED slave address referenced in the command is not
defined in the module. Check to make sure there is an entry
in the slave table for each slave device referenced in the
command list.
2 Invalid command This command is not valid. Check to make sure the slave
address parameter is greater than or equal to zero and that
the point count is not set to zero.
3 Object not supported The data object in the command is not supported by the
module. Refer to the DNP subset for the Master Port.
4 Command function not The function specified in the command is not supported for
supported the object type selected. Refer to the DNP subset for the
Master Port.
10 Invalid binary input poll This binary input object command is not valid.
command
11 Invalid binary input This binary input event object poll command is not valid.
event poll command
20 Invalid binary output This binary output command function is not valid.
command function
30 Invalid counter poll The counter object poll command contains an invalid function
command function code.
31 Invalid counter poll This counter object poll command is not valid.
command
40 Invalid frozen counter This frozen counter object poll command is not valid.
poll command
50 Invalid analog input poll This analog input poll command is not valid.
command
51 Invalid analog input This analog input event poll command is not valid.
event poll command

November 3, 2008

Code
60 Invalid analog output This analog output poll command contains an invalid function
poll command function code.
61 Invalid analog output This analog output poll command is not valid.
poll command
70 Invalid time/date poll This time/date object poll command is not valid.
command
80 Invalid event poll This event poll command is not valid.
command
Application Layer Errors

Code
1000 Device index invalid The device index in the request or response message is not
found in the slave list.
1001 Duplicate request in The newly submitted message to the application layer
application layer queue already exists in the queue. The message is ignored.
1002 COM port device The communication port for the message has been
removed from system uninstalled on the system. This error should never occur as
the communication ports are only uninstalled when the
module's program is terminated.
1003 Sequence number error The application sequence number in the response message
does not match that based on the last request message. This
indicates application layer messages are received out of
order.
1004 Response to select The select response message received from the slave
before operate does not module is not that expected from the last select request. This
match indicates a synchronization problem between the master and
slave devices.
1005 Response does not The response message from the slave device does not
contain date/time object contain a date/time object. The master expects this object for
the response message.
1006 Time-out condition on The slave device did not respond to the last request
response message from the master within the time-out set for the IED
device. The application layer time-out value is specified for
each IED unit in the slave configuration table in the module.
This table is established each time the module performs the
restart operation.
1007 Function code in The function code returned in the response message is not
application layer valid for the application layer or not supported by the module.
message not supported
1008 Read operation not The application layer response message contains an object
supported for that does not support the read function.
object/variation
1009 Operate function not The application layer response message contains an object
supported for the that does not support the operate function.
object/variation
1010 Write operation not The application layer response message contains an object
supported for the that does not support the write function.
object/variation

November 3, 2008
5.5 Internal Indication Word
5.5.1 First Byte

Bit Description
0 All stations message received. Set when a request is received with the destination
address set to 0xffff. Cleared after next response. Used to let master station know
broadcast received.
1 Class 1 data available. Set when class 1 data is ready to be sent from the slave to
the master. Master should request class 1 data when this bit is set.
4 Time synchronization required from master. The master should write the date and
time when this bit is set. After receiving the write command the bit will be cleared.
5 Slave digital outputs are in local control. This bit is not used in this application.
6 Not used
7 Device restart. This bit is set when the slave either warm or cold boots. It is cleared
after a master writes a 0 to the bit.
5.5.2 Second Byte:

Bit Description
0 Bad function code. The function code contained in the master request is not
supported for the specified object/variation.
1 Requested object(s) unknown. Object requested by master is not supported by the
application.
2 Parameters in the qualifier, range or data fields are not valid or out of range for the
slave.
3 Event buffer(s) or other application buffers have overflowed. This bit is also set if the
slave receives a multi-frame message from the master.
4 Request understood but requested operation is already executing. The slave will
never set this bit.
5 Bad configuration. The slave configuration is invalid and should be re-configured. If
the configuration is invalid, the slave will set the invalid parameters to default values
and continue to run. Check error log using debug port.
6 Reserved, always 0.
7 Reserved, always 0.

November 3, 2008
5.6 DNP V3.00 Device Profile Document

Vendor Name: ProSoft Technology, Inc.
Device Name: MVI69-DNP (Revision 1.00)
Highest DNP Level Supported: Device Function:
For Request: L2 Slave & Master
For Responses: L2
Notable objects, functions, and/or qualifiers supported in addition to the highest DNP level stated above (see attached
table for complete list):
Definition of selected IIN bits: Configuration Error - User specified point or event count is too high for application (can only
correct by changing configuration in PLC).
Support for a redundant slave port on the module which may be attached to a dial-up modem is provided. Auto switching
is provided by the module to switch between the primary and secondary ports.
The following features are configurable on the module: Collision avoidance, time sync before events are generated and
default analog input events, Obj32V4 or O32V2, select option.
Events generated by IED units attached to a master port may pass their events directly to the slave port. These events
may not occur in the correct time sequence. They are placed in the event buffer as the module receives them. This
provides the greatest time resolution for remote events.
Module will not generate events until Restart IIN bit is cleared by DNP master except for events passed through module
from attached IED units.
Maximum Data Link Frame Size (octets): Maximum Application Fragment Size (octets):
Transmitted: 292 Transmitted: 2048
Received: 292 Received: 2048
Maximum Data Link Re-tries: Maximum Application Layer Retries:
Configurable from 0 - 255 None
Requires Data Link Layer Confirmation:
Configurable at module start-up (never, sometimes, & always)
Requires Application Layer Confirmation:
When reporting Event Data as a slave unit
Time-outs while waiting for:
Data Link Confirm : Configurable at module start-up (1 to 65535 milliseconds)
Complete Application Fragment : Configurable at module start-up
Application Confirm : Configurable at module start-up (1 to 65535 milliseconds)
Complete Application Response : None
Sends/Executes Control Operations:
WRITE Binary Outputs : Never
SELECT/OPERATE : Always
DIRECT OPERATE : Always
DIRECT OPERATE-NO ACK : Always
Count > 1 : Always (1 to 65535)

Pulse On : Always
Pulse Off : Always
Latch On : Always
Latch Off : Always

November 3, 2008
Queue : Never
Clear Queue : Never
Reports Binary Input Change Events when no specific Reports time-tagged Binary Input Change Events when no
variation requested: specific variation requested:
Only time-tagged Binary Input Change with Time
Sends Unsolicited Responses: Sends Static Data in Unsolicited Responses:
This is configurable at module start-up. If the number of Never
events for the Binary or Analog Input Events is greater
than 0, unsolicited responses are supported. Use the
Enable/Disable Unsolicited function code from the DNP
master for control.
Default Counter Object/Variation: Counters Roll Over at:
Object : 20 32 Bits
Variation :5
Sends Multi-Fragment Responses: Yes
5.7 DNP Subset Definition - Slave

OBJECT REQUEST RESPONSE
Obj Var Description Func Qual Func Qual Data NOTES
Codes Codes Codes Codes Size
(hex) (hex) (bits)
1 0 Binary Input: All 1 06 1 Slave will return variation 1
Variations data
1 Binary Input 1 06 129, 130 00, 01 1 Slave will return this
variation
2 Binary Input with 129, 130 00, 01 8 Slave will return Unknown
Status Object to this request
2 0 Binary Input 1 06, 07, 08 56 Slave will return variation 2
Change: All data
Variations
1 Binary Input 1 06, 07, 08 129, 130 17, 28 8 Slave will return this
Change Without variation
Time
2 Binary Input 1 06, 07, 08 129, 130 17, 28 56 Slave will return this
Change With variation
Time
3 Binary Input 1 06, 07, 08 129, 130 17, 28 24 Slave will parse this
Change With message and return no data
Relative Time
10 0 Binary Output: All 1 06 8 Slave will return variation 2
Variations data
1 Binary Output 1 Slave will return Unknown
Object to this request
2 Binary Output 1 06 129, 130 00, 01 8 Slave will return this
Status variation
12 0 Control Block: All 88 Slave will use variation 1
Variations control
1 Control Relay 3, 4, 5, 17, 28 129 Echo of 88 Slave will respond correctly
Output Block 6 request to this variation

November 3, 2008

(hex) (hex) (bits)
2 Pattern Control 88 Slave will return Unknown
Block Object to this request
3 Pattern Mask 16 Slave will return Unknown
Object to this request
20 0 Binary Counter: 1, 7, 8, 06 32 Slave will return variation 5
All Variations 9, 10 data
1 32-Bit Binary 129, 130 00, 01 40 Slave will return Unknown
Counter Object to this request
2 16-Bit Binary 129, 130 00, 01 24 Slave will return Unknown
3 32-Bit Delta 129, 130 00, 01 40 Slave will return Unknown
5 32-Bit Binary 1, 7, 8, 06 129, 130 00, 01 32 Slave will return this
Counter Without 9, 10 variation
Flag
6 16-Bit Binary 1, 7, 8, 06 129, 130 00, 01 16 Slave will return this
Counter Without 9, 10 variation (counter upper 16-
Flag bits removed)
Counter Without Object to this request
Flag
Counter Without Object to this request
Flag
21 0 Frozen Counter: 1 06 32 Slave will return variation 9
All Variations data
1 32-Bit Frozen 129, 130 00, 01 40 Slave will return Unknown
2 16-Bit Frozen 129, 130 00, 01 24 Slave will return Unknown
3 32-Bit Frozen 40 Slave will return Unknown
Delta Counter Object to this request
Counter With Object to this request
Time Of Freeze
Counter With Object to this request
Time Of Freeze
With Time Of
Freeze

November 3, 2008

(hex) (hex) (bits)
With Time Of
Freeze
9 32-Bit Frozen 1 06 129, 130 00, 01 32 Slave will return this
Counter Without variation
Flag
10 16-Bit Frozen 1 06 129, 130 00, 01 16 Slave will return this
Counter Without variation (counter upper 16-
Flag bits removed)
Without Flag
Without Flag
22 0 Counter Change 1 06, 07, 08 Slave will parse this request
Event: All and return no data
Variations
1 32-Bit Counter 129, 130 17, 28 40 Slave will return Unknown
Change Event Object to this request
Without Time
2 16-Bit Counter 129, 130 17, 28 24 Slave will return Unknown
Without Time
3 32-Bit Delta 40 Slave will return Unknown
Counter Change Object to this request
Event Without
Time
Event Without
Time
5 32-Bit Counter 88 Slave will return Unknown
With Time
6 16-Bit Counter 72 Slave will return Unknown
With Time
Event With Time
Event With Time
23 0 Frozen Counter Slave will return Unknown
Event: All Object to this request
Variations

November 3, 2008

(hex) (hex) (bits)
Counter Event Object to this request
Without Time
Without Time
Event Without
Time
Event Without
Time
With Time
With Time
Event With Time
Event With Time
30 0 Analog Input: All 1 06 16 Slave will respond with
Variations variation 4 data
1 32-Bit Analog 1 06 129, 130 00, 01 40 Slave will return this
Input variation (Note: Data will
only be 16-bit)
Input variation
Input Without Flag variation (Note: Data will
only be 16-bit)
Input Without Flag variation
31 0 Frozen Analog Slave will return Unknown
Input: All Object to this request
Variations
Analog Input Object to this request
Analog Input With Object to this request
Time To Freeze

November 3, 2008

(hex) (hex) (bits)
Analog Input With Object to this request
Time To Freeze
Without Flag
Without Flag
32 0 Analog Change 1 06, 07, 08 24 Slave will return variation 2
Event: All data
Variations
1 32-Bit Analog 1 06, 07, 08 129, 130 17, 28 40 Slave will return this
Change Event variation (Note: Data only
Without Time 16-bit)
Change Event variation
Without Time
Change Event variation (Note: Data only
With Time 16-bit)
With Time
33 0 Frozen Analog Slave will return Unknown
Event: All Object to this request
Variations
Analog Event Object to this request
Without Time
Analog Event Object to this request
Without Time
Analog Event With Object to this request
Time
Analog Event With Object to this request
Time
40 0 Analog Output 1 06 24 Slave will return variation 2
Status: All data
Variations
1 32-Bit Analog 1 06 129,130 00,01 40 Slave will return this
Output Status variation but data only 16-bit
accuracy
Output Status variation

November 3, 2008

(hex) (hex) (bits)
41 0 Analog Output 24 Slave will respond to this
Block: All request using variation 2
Variations data
1 32-Bit Analog 3, 4, 5, 17, 28 129,130 00,01 40 Slave will respond to this
Output Block 6 request but data only 16-bit
2 16-Bit Analog 3, 4, 5, 17, 28 129 Echo of 24 Slave will respond to this
Output Block 6 Request request
50 0 Time and Date: All 2 07, With 48 Slave will use variation 1
Variations Quant=1
1 Time and Date 2 07, With 48 Slave will respond to this
Quant=1 variation
2 Time and Date 80 Slave will return Unknown
With Interval Object to this request
51 0 Time and Date Slave will return Unknown
CTO: All Object to this request
Variations
1 Time and Date 129, 130 07, With 48 Slave will return Unknown
CTO Quant=1 Object to this request
2 Unsynchronized 129, 130 07, With 48 Slave will return Unknown
Time and Date Quant=1 Object to this request
CTO
52 0 Time Delay: All
Variations
1 Time Delay 129 07, With 16 Slave will never return this
Coarse Quant=1 variation
2 Time Delay Fine 129 07, With 16 Slave will return this
Quant=1 variation to functions 0D,
0E, and 17
60 0 Not Defined Not Defined in DNP
1 Class 0 Data 1 06 Slave will respond to this
variation with all static data
2 Class 1 Data 1 06, 07, 08 Slave will respond to this
variation (No class 1 data
defined in application)
variation with all class 2
data (binary input events)
variation with all class 3
data (analog input events)
1 File Identifier
1 Internal 2 00, 24 Slave will respond to this
Indications Index=7 variation

November 3, 2008

(hex) (hex) (bits)
1 Storage Object
1 Device Profile
1 Private
Registration
Object
2 Private
Registration
Objection
Descriptor
1 Application
Identifier
100 0
1 Short Floating 48
Point
2 Long Floating 80
Point
3 Extended Floating 88
Point
101 0
1 Small Packed 16
Binary-Coded
Decimal
2 Medium Packed 32
Binary-Coded
Decimal
3 Large Packed 64
Binary-Coded
Decimal
No Object 13 Slave supports the Cold
Restart Function and will
return Obj 52, Var 2, Qual 7,
Cnt 1
14 Slave supports the Warm
Restart Function and will
return Obj 52, Var 2, Qual 7,
Cnt 1
20 Slave supports the Enable
Unsolicited Function
21 Slave supports the Disable
Unsolicited Function

November 3, 2008

(hex) (hex) (bits)
23 Slave supports the Delay
Measurement & Time
Synchronization Function
and will return Obj 52, Var
2, Qual 7, Cnt 1
5.8 DNP Subset Definition - Master

(hex) (hex) (bits)
1 0 Binary Input: All 1 06 1 Master will generate this
Variations variation
1 Binary Input 1 06 129, 130 00, 01 1 Master will generate and
process this variation
2 Binary Input with 1 06 129, 130 00, 01 8 Master will generate and
Status process this variation
2 0 Binary Input Change: 1 06, 07, 08 56 Master will generate this
All Variations variation
1 Binary Input Change 1 06, 07, 08 129, 130 17, 28 8 Master will generate and
Without Time process this variation
With Time process this variation
With Relative Time process this variation
10 0 Binary Output: All 1 06 8 Master does not use this
Variations object type and will not
generate a message or
1 Binary Output 1
process this type
2 Binary Output Status 129, 130 00, 01 8
12 0 Control Block: All 88
Variations
1 Control Relay Output 3, 4, 5, 6 17, 28 129 Echo of 88 Master will generate this
Block request variation and parse the
response
2 Pattern Control Block 88
3 Pattern Mask 16
20 0 Binary Counter: All 1, 7, 8, 06 32 Master will generate this
Variations 9, 10 variation
1 32-Bit Binary 129, 130 00, 01 40 Master will process this
Counter variation
2 16-Bit Binary 129, 130 00, 01 24 Master will process this
Counter variation
3 32-Bit Delta Counter 129, 130 00, 01 40 Master will process this
variation

November 3, 2008

(hex) (hex) (bits)
variation
5 32-Bit Binary 1, 7, 8, 06 129, 130 00, 01 32 Master will generate and
Counter Without Flag 9, 10 process this variation
6 16-Bit Binary 1, 7, 8, 06 129, 130 00, 01 16 Master will generate and
Counter Without Flag 9, 10 process this variation
Without Flag variation
Without Flag variation
21 0 Frozen Counter: All 1 06 32 Master will generate this
1 32-Bit Frozen 129, 130 00, 01 40 Master will process this
Counter variation
2 16-Bit Frozen 129, 130 00, 01 24 Master will process this
Counter variation
3 32-Bit Frozen Delta 40
Counter
Counter
5 32-Bit Frozen 88
Counter With Time
Of Freeze
6 16-Bit Frozen 72
Counter With Time
Of Freeze
Counter With Time
Of Freeze
Counter With Time
Of Freeze
9 32-Bit Frozen 1 06 129, 130 00, 01 32 Master will generate and
Counter Without Flag process this variation
10 16-Bit Frozen 1 06 129, 130 00, 01 16 Master will generate and
Counter Without Flag process this variation
Counter Without Flag
Counter Without Flag
22 0 Counter Change 1 06, 07, 08 Master will not generate a
Event: All Variations request for this variation
1 32-Bit Counter 129, 130 17, 28 40 Master will process this
Without Time

November 3, 2008

(hex) (hex) (bits)
2 16-Bit Counter 129, 130 17, 28 24 Master will process this
Without Time
3 32-Bit Delta Counter 40
Change Event
Without Time
Change Event
Without Time
5 32-Bit Counter 88
Change Event With
Time
6 16-Bit Counter 72
Change Event With
Time
Change Event With
Time
Change Event With
Time
23 0 Frozen Counter
Event: All Variations
1 32-Bit Frozen 40
Counter Event
Without Time
2 16-Bit Frozen 24
Counter Event
Without Time
Counter Event
Without Time
Counter Event
Without Time
5 32-Bit Frozen 88
Counter Event With
Time
6 16-Bit Frozen 72
Counter Event With
Time
Counter Event With
Time
Counter Event With
Time
30 0 Analog Input: All 1 06 16 Master will generate this

November 3, 2008

(hex) (hex) (bits)
1 32-Bit Analog Input 1 06 129, 130 00, 01 40 Master will generate and
(Data returned will be
only 16 bit)
Without Flag process this variation
(Data returned will be
only 16 bit)
Without Flag process this variation
31 0 Frozen Analog Input:
All Variations
1 32-Bit Frozen Analog 40
Input
Input
Input With Time To
Freeze
Input With Time To
Freeze
Input Without Flag
Input Without Flag
32 0 Analog Change 1 06, 07, 08 24 Master will generate this
Event: All Variations variation
1 32-Bit Analog 1 06, 07, 08 129, 130 17, 28 40 Master will generate and
Change Event process this variation
Without Time
Change Event process this variation
Without Time
Change Event With process this variation
Time
Change Event With process this variation
Time
33 0 Frozen Analog
Event: All Variations
Event Without Time
Event Without Time

November 3, 2008

(hex) (hex) (bits)
Event With Time
Event With Time
40 0 Analog Output 1 06 24 Master does not use this
Status: All Variations object type and will not
generate a message or
1 32-Bit Analog Output 40
process this type
Status
2 16-Bit Analog Output 129, 130 00, 01 24
Status
41 0 Analog Output Block: 24
All Variations
1 32-Bit Analog Output 40
Block
2 16-Bit Analog Output 3, 4, 5, 6 17, 28 129 Echo of 24 Master will generate this
Block Request variation and parse the
response
50 0 Time and Date: All 48
Variations
1 Time and Date 2 07, With 48 Master will generate this
Quant=1 variation
2 Time and Date With 80
Interval
51 0 Time and Date CTO:
All Variations
1 Time and Date CTO 129, 130 07, With 48 Master will process this
Quant=1 variation
2 Unsynchronized 129, 130 07, With 48 Master will process this
Time and Date CTO Quant=1 variation
52 0 Time Delay: All
Variations
1 Time Delay Coarse 129 07, With 16 Master will not process
Quant=1 this variation
2 Time Delay Fine 129 07, With 16 Master will not process
Quant=1 this variation
1 Class 0 Data 1 06 Master will generate this
variation
2 Class 1 Data 1 06, 07, 08 Master will generate this
variation
variation
variation
70 0 Not Defined

November 3, 2008

(hex) (hex) (bits)
1 File Identifier
80 0 Not Defined
1 Internal Indications 2 00, 24 The Master will generate
Index=7 this variation
81 0 Not Defined
1 Storage Object
82 0 Not Defined
1 Device Profile
1 Private Registration
Object
2 Private Registration
Objection Descriptor
1 Application Identifier
100 0
1 Short Floating Point 48
2 Long Floating Point 80
3 Extended Floating 88
Point
101 0
1 Small Packed 16
Binary-Coded
Decimal
2 Medium Packed 32
Binary-Coded
Decimal
3 Large Packed 64
Binary-Coded
Decimal
No Object 13 Master supports the Cold
Restart Function
14 Master supports the
Warm Restart Function
Enable Unsolicited
Function
Disable Unsolicited
Function

November 3, 2008

November 3, 2008
Support, Service & Warranty MVI69-DNP ♦ CompactLogix or MicroLogix Platform
6 Support, Service & Warranty
In This Chapter
How to Contact Us: Technical Support................................................ 119
Return Material Authorization (RMA) Policies and Conditions............. 120
LIMITED WARRANTY......................................................................... 122
ProSoft Technology, Inc. (ProSoft) is committed to providing the most efficient

and effective support possible. Before calling, please gather the following
information to assist in expediting this process:
1 Product Version Number
2 System architecture
3 Network details
If the issue is hardware related, we will also need information regarding:
1 Module configuration and contents of file
o Module Operation
o Configuration/Debug status information
o LED patterns
2 Information about the processor and user data files as viewed through and
LED patterns on the processor.
3 Details about the serial devices interfaced, if any.
6.1 How to Contact Us: Technical Support

Internet Web Site: http://www.prosoft-technology.com/support
(http://www.prosoft-technology.com/support)
E-mail address: support@prosoft-technology.com
(mailto:support@prosoft-technology.com)
Asia Pacific
+603.7724.2080, support.asia@prosoft-technology.com
(mailto:support.asia@prosoft-technology.com)
Languages spoken include: Chinese, English
Europe (location in Toulouse, France)

+33 (0) 5.34.36.87.20, support.EMEA@prosoft-technology.com
(mailto:support.emea@prosoft-technology.com)
Languages spoken include: French, English

November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Support, Service & Warranty
North America/Latin America (excluding Brasil) (location in California)

+1.661.716.5100, support@prosoft-technology.com (mailto:support@prosoft-
technology.com)
Languages spoken include: English, Spanish
For technical support calls within the United States, an after-hours answering
system allows pager access to one of our qualified technical and/or application
support engineers at any time to answer your questions.
Brasil (location in Sao Paulo)

+55-11-5084-5178 , eduardo@prosoft-technology.com (mailto:eduardo@prosoft-
technology.com)
Languages spoken include: Portuguese, English
6.2 Return Material Authorization (RMA) Policies and Conditions

The following RMA Policies and Conditions (collectively, "RMA Policies") apply to
any returned Product. These RMA Policies are subject to change by ProSoft
without notice. For warranty information, see "Limited Warranty". In the event of
any inconsistency between the RMA Policies and the Warranty, the Warranty
shall govern.
6.2.1 All Product Returns:

a) In order to return a Product for repair, exchange or otherwise, the
Customer must obtain a Returned Material Authorization (RMA) number
from ProSoft and comply with ProSoft shipping instructions.
b) In the event that the Customer experiences a problem with the Product for
any reason, Customer should contact ProSoft Technical Support at one of
the telephone numbers listed above (page 119). A Technical Support
Engineer will request that you perform several tests in an attempt to
isolate the problem. If after completing these tests, the Product is found to
be the source of the problem, we will issue an RMA.
c) All returned Products must be shipped freight prepaid, in the original
shipping container or equivalent, to the location specified by ProSoft, and
be accompanied by proof of purchase and receipt date. The RMA number
is to be prominently marked on the outside of the shipping box. Customer
agrees to insure the Product or assume the risk of loss or damage in
transit. Products shipped to ProSoft using a shipment method other than
that specified by ProSoft or shipped without an RMA number will be
returned to the Customer, freight collect. Contact ProSoft Technical
Support for further information.
d) A 10% restocking fee applies to all warranty credit returns whereby a
Customer has an application change, ordered too many, does not need,
etc.

November 3, 2008
6.2.2 Procedures for Return of Units Under Warranty:

A Technical Support Engineer must approve the return of Product under
ProSoft's Warranty:
a) A replacement module will be shipped and invoiced. A purchase order will
be required.
b) Credit for a product under warranty will be issued upon receipt of
authorized product by ProSoft at designated location referenced on the
Return Material Authorization.
6.2.3 Procedures for Return of Units Out of Warranty:

a) Customer sends unit in for evaluation
b) If no defect is found, Customer will be charged the equivalent of $100
USD, plus freight charges, duties and taxes as applicable. A new
purchase order will be required.
c) If unit is repaired, charge to Customer will be 30% of current list price
(USD) plus freight charges, duties and taxes as applicable. A new
purchase order will be required or authorization to use the purchase order
submitted for evaluation fee.
The following is a list of non-repairable units:
o 3150 - All
o 3750
o 3600 - All
o 3700
o 3170 - All
o 3250
o 1560 - Can be repaired, only if defect is the power supply
o 1550 - Can be repaired, only if defect is the power supply
o 3350
o 3300
o 1500 - All
6.2.4 Purchasing Warranty Extension:

a) ProSoft's standard warranty period is three (3) years from the date of
shipment as detailed in "Limited Warranty (page 122)". The Warranty
Period may be extended at the time of equipment purchase for an
additional charge, as follows:
• Additional 1 year = 10% of list price
• Additional 2 years = 20% of list price
• Additional 3 years = 30% of list price

November 3, 2008
6.3 LIMITED WARRANTY

This Limited Warranty ("Warranty") governs all sales of hardware, software and
other products (collectively, "Product") manufactured and/or offered for sale by
ProSoft, and all related services provided by ProSoft, including maintenance,
repair, warranty exchange, and service programs (collectively, "Services"). By
purchasing or using the Product or Services, the individual or entity purchasing or
using the Product or Services ("Customer") agrees to all of the terms and
provisions (collectively, the "Terms") of this Limited Warranty. All sales of
software or other intellectual property are, in addition, subject to any license
agreement accompanying such software or other intellectual property.
6.3.1 What Is Covered By This Warranty

a) Warranty On New Products: ProSoft warrants, to the original purchaser,
that the Product that is the subject of the sale will (1) conform to and
perform in accordance with published specifications prepared, approved
and issued by ProSoft, and (2) will be free from defects in material or
workmanship; provided these warranties only cover Product that is sold as
new. This Warranty expires three years from the date of shipment (the
"Warranty Period"). If the Customer discovers within the Warranty Period
a failure of the Product to conform to specifications, or a defect in material
or workmanship of the Product, the Customer must promptly notify
ProSoft by fax, email or telephone. In no event may that notification be
received by ProSoft later than 39 months. Within a reasonable time after
notification, ProSoft will correct any failure of the Product to conform to
specifications or any defect in material or workmanship of the Product,
with either new or used replacement parts. Such repair, including both
parts and labor, will be performed at ProSoft's expense. All warranty
service will be performed at service centers designated by ProSoft.
b) Warranty On Services: Materials and labor performed by ProSoft to repair
a verified malfunction or defect are warranteed in the terms specified
above for new Product, provided said warranty will be for the period
remaining on the original new equipment warranty or, if the original
warranty is no longer in effect, for a period of 90 days from the date of
repair.
6.3.2 What Is Not Covered By This Warranty

a) ProSoft makes no representation or warranty, expressed or implied, that
the operation of software purchased from ProSoft will be uninterrupted or
error free or that the functions contained in the software will meet or
satisfy the purchaser's intended use or requirements; the Customer
assumes complete responsibility for decisions made or actions taken
based on information obtained using ProSoft software.

November 3, 2008
b) This Warranty does not cover the failure of the Product to perform
specified functions, or any other non-conformance, defects, losses or
damages caused by or attributable to any of the following: (i) shipping; (ii)
improper installation or other failure of Customer to adhere to ProSoft's
specifications or instructions; (iii) unauthorized repair or maintenance; (iv)
attachments, equipment, options, parts, software, or user-created
programming (including, but not limited to, programs developed with any
IEC 61131-3, "C" or any variant of "C" programming languages) not
furnished by ProSoft; (v) use of the Product for purposes other than those
for which it was designed; (vi) any other abuse, misapplication, neglect or
misuse by the Customer; (vii) accident, improper testing or causes
external to the Product such as, but not limited to, exposure to extremes
of temperature or humidity, power failure or power surges; or (viii)
disasters such as fire, flood, earthquake, wind and lightning.
c) The information in this Agreement is subject to change without notice.
ProSoft shall not be liable for technical or editorial errors or omissions
made herein; nor for incidental or consequential damages resulting from
the furnishing, performance or use of this material. The user guide
included with your original product purchase from ProSoft contains
information protected by copyright. No part of the guide may be duplicated
or reproduced in any form without prior written consent from ProSoft.
6.3.3 Disclaimer Regarding High Risk Activities

Product manufactured or supplied by ProSoft is not fault tolerant and is not
designed, manufactured or intended for use in hazardous environments requiring
fail-safe performance including and without limitation: the operation of nuclear
facilities, aircraft navigation of communication systems, air traffic control, direct
life support machines or weapons systems in which the failure of the product
could lead directly or indirectly to death, personal injury or severe physical or
environmental damage (collectively, "high risk activities"). ProSoft specifically
disclaims any express or implied warranty of fitness for high risk activities.
6.3.4 Intellectual Property Indemnity

Buyer shall indemnify and hold harmless ProSoft and its employees from and
against all liabilities, losses, claims, costs and expenses (including attorney's
fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not ProSoft is a party) which arises or is alleged to arise from Buyer's
acts or omissions under these Terms or in any way with respect to the Products.
Without limiting the foregoing, Buyer (at its own expense) shall indemnify and
hold harmless ProSoft and defend or settle any action brought against such
Companies to the extent based on a claim that any Product made to Buyer
specifications infringed intellectual property rights of another party. ProSoft
makes no warranty that the product is or will be delivered free of any person's
claiming of patent, trademark, or similar infringement. The Buyer assumes all
risks (including the risk of suit) that the product or any use of the product will
infringe existing or subsequently issued patents, trademarks, or copyrights.

November 3, 2008
a) Any documentation included with Product purchased from ProSoft is

protected by copyright and may not be duplicated or reproduced in any
form without prior written consent from ProSoft.
b) ProSoft's technical specifications and documentation that are included
with the Product are subject to editing and modification without notice.
c) Transfer of title shall not operate to convey to Customer any right to make,
or have made, any Product supplied by ProSoft.
d) Customer is granted no right or license to use any software or other
intellectual property in any manner or for any purpose not expressly
permitted by any license agreement accompanying such software or other
intellectual property.
e) Customer agrees that it shall not, and shall not authorize others to, copy
software provided by ProSoft (except as expressly permitted in any
license agreement accompanying such software); transfer software to a
third party separately from the Product; modify, alter, translate, decode,
decompile, disassemble, reverse-engineer or otherwise attempt to derive
the source code of the software or create derivative works based on the
software; export the software or underlying technology in contravention of
applicable US and international export laws and regulations; or use the
software other than as authorized in connection with use of Product.
f) Additional Restrictions Relating To Software And Other Intellectual
Property
In addition to compliance with the Terms of this Warranty, Customers
purchasing software or other intellectual property shall comply with any
license agreement accompanying such software or other intellectual
property. Failure to do so may void this Warranty with respect to such
software and/or other intellectual property.
6.3.5 Disclaimer of all Other Warranties

The Warranty set forth in What Is Covered By This Warranty (page 122) are in
lieu of all other warranties, express or implied, including but not limited to the
implied warranties of merchantability and fitness for a particular purpose.
6.3.6 Limitation of Remedies **

In no event will ProSoft or its Dealer be liable for any special, incidental or
consequential damages based on breach of warranty, breach of contract,
negligence, strict tort or any other legal theory. Damages that ProSoft or its
Dealer will not be responsible for included, but are not limited to: Loss of profits;
loss of savings or revenue; loss of use of the product or any associated
equipment; loss of data; cost of capital; cost of any substitute equipment,
facilities, or services; downtime; the claims of third parties including, customers of
the Purchaser; and, injury to property.
** Some areas do not allow time limitations on an implied warranty, or allow the exclusion or
limitation of incidental or consequential damages. In such areas, the above limitations may not
apply. This Warranty gives you specific legal rights, and you may also have other rights which vary
from place to place.

November 3, 2008
6.3.7 Time Limit for Bringing Suit

Any action for breach of warranty must be commenced within 39 months
following shipment of the Product.
6.3.8 No Other Warranties

Unless modified in writing and signed by both parties, this Warranty is
understood to be the complete and exclusive agreement between the parties,
suspending all oral or written prior agreements and all other communications
between the parties relating to the subject matter of this Warranty, including
statements made by salesperson. No employee of ProSoft or any other party is
authorized to make any warranty in addition to those made in this Warranty. The
Customer is warned, therefore, to check this Warranty carefully to see that it
correctly reflects those terms that are important to the Customer.
6.3.9 Allocation of Risks

This Warranty allocates the risk of product failure between ProSoft and the
Customer. This allocation is recognized by both parties and is reflected in the
price of the goods. The Customer acknowledges that it has read this Warranty,
understands it, and is bound by its Terms.
6.3.10 Controlling Law and Severability

This Warranty shall be governed by and construed in accordance with the laws of
the United States and the domestic laws of the State of California, without
reference to its conflicts of law provisions. If for any reason a court of competent
jurisdiction finds any provisions of this Warranty, or a portion thereof, to be
unenforceable, that provision shall be enforced to the maximum extent
permissible and the remainder of this Warranty shall remain in full force and
effect. Any cause of action with respect to the Product or Services must be
instituted in a court of competent jurisdiction in the State of California.

November 3, 2008

November 3, 2008
Index MVI69-DNP ♦ CompactLogix or MicroLogix Platform
Displaying the Current Page of Registers Again • 62

DNP Database View Menu • 58, 61
DNP DB Address • 33
DNP Port Configuration Errors • 100
Index DNP Subset Definition - Master • 112
DNP Subset Definition - Slave • 105
DNP V3.00 Device Profile Document • 104
A DNP_AI_Event Object • 46
DNP_BI_Event Object • 46
Adding the Module to an Existing CompactLogix DNPBackplane Object • 44
Project • 47 DNPCROB Object • 45
Adding the Module to an Existing MicroLogix Project • DNPData Object • 44
50 DNPEventMsg Object • 45
Address In Slave • 33 DNPModuleDef Object • 41
All Product Returns: • 120 DNPSlave_Err Object • 46
Allocation of Risks • 125 DNPSlvStat Object • 42
Application Layer Errors • 102 Download the Sample Program to the Processor • 16
B E
Backplane Data Transfer • 73 Editing the Configuration File • 22
Battery Life Advisory • 2 Error Status Table • 95
Block 9901 - Event Command • 77
Block 9902 - Command Control Block • 79 F
Block 9903 - Event Message Block • 79 First Byte • 103
Block 9949 - Read Slave Communication Error Table • Function • 33
80 Functional Overview • 7, 72
Block 9950 - Read Command Error List • 81 Functional Specifications • 70
Block 9958 - Processor Binary Input Event • 82
Block 9959 - Processor Analog Input Event • 83 G
Block 9970 - Set Processor Time Using Module Time •
84 General Command Errors • 101
Block 9971 - Set Module's Time Using the Processor's General Concepts • 72
Time • 85 General Specifications • 69
Block Format for Read • 78, 79, 81, 82, 83, 84, 85 Guide to the MVI69-DNP User Manual • 7
Block Format for Write • 77, 79, 80, 81, 82, 83, 84, 85
H
C Hardware Specifications • 70
Cable Connections • 89 How to Contact Us
Clearing a Fault Condition • 67 Technical Support • 119, 120
Clearing the Error List • 57
Cold Boot • 86
I
Command Control Blocks • 77 IED DB Address • 33
Command Error Codes • 101 Install the Module in the Rack • 12
Command List • 29 Intellectual Property Indemnity • 123
Configuration File • 21 Internal Indication Word • 103
Configuring RSLinx • 17
Configuring the MVI69-DNP Module • 21 K
Connect your PC to the Module • 19
Keystrokes • 54
Connect your PC to the Processor • 15
Controlling Law and Severability • 125 L
D Ladder Logic • 41
LED Status Indicators • 7, 66
Data Flow between MVI69-DNP Module and
Limitation of Remedies ** • 124
CompactLogix Processor • 87
LIMITED WARRANTY • 121, 122
DB9 to RJ45 Adaptor (Cable 14) • 94
Diagnostics and Troubleshooting • 7, 51, 53 M
Disabling the RSLinx Driver for the Com Port on the
PC • 55, 90 Main Logic Loop • 72
Disclaimer of all Other Warranties • 124 Main Menu • 56
Disclaimer Regarding High Risk Activities • 123 Master Command Error List Menu • 65

November 3, 2008
MVI69-DNP ♦ CompactLogix or MicroLogix Platform Index
Master Command List Menu • 64 Setting the Debug Level • 56

Master Driver Mode • 88 Skipping 500 Registers of Data • 62
Module Data Objects • 41 Slave Address • 33
Module Error Codes • 99 Slave Driver • 87
Module Power Up • 72 Slave List • 29
Moving Back Through 5 Pages of Registers • 62 Slave Port Communication Errors • 99
MVI69-DNP Communication Module Configuration • 23 Special Objects • 45
Start Here • 7, 9
N Support, Service & Warranty • 7, 119
Navigation • 54 System Configuration Errors • 100
No Other Warranties • 125 System Requirements • 9
Normal Data Transfer • 75 T
O The Class Assignment Menu • 59
Object • 33 The Configuration/Debug Menu • 34, 53
OCTET STRING POINT LIST • 88 Time Limit for Bringing Suit • 125
Opening the Class Assignment Menu • 58 Transferring the Configuration File to the Module • 36
Opening the Command Error List Menu • 59 Transferring the Configuration File to Your PC • 34
Opening the Command List Menu • 59 Troubleshooting • 68
Opening the DNP Database View Menu • 58 U
P Uploading and Downloading the Configuration File •
Package Contents • 10 21, 34, 58
Pinouts • 89, 94 Using the Configuration/Debug Port • 55
Please Read This Notice • 2 V
Point Count • 33
Poll Interval • 34 Variation • 33
Procedures for Return of Units Out of Warranty: • 121 Viewing Analog Inputs • 60
Procedures for Return of Units Under Warranty: • 121 Viewing Binary Inputs • 60
Product Specifications • 7, 69 Viewing Block Transfer Statistics • 58
ProSoft® Product Documentation • 3 Viewing COM States • 57
Purchasing Warranty Extension: • 121 Viewing Comm Stats • 57
Viewing Data in ASCII (Text) Format • 63
R Viewing Data in Decimal Format • 62
Read Block • 76 Viewing Data in Double Word Decimal Format • 63
Reading Status Data from the Module • 53 Viewing Data in Floating Point Format • 63
Receiving the Configuration File • 58 Viewing Data in Hexadecimal Format • 62
Redisplaying the Current Page • 60, 64, 65 Viewing Data Type Databases • 61
Reference • 7, 69 Viewing DNP Analog Inputs • 63
Required Hardware • 54 Viewing DNP Analog Outputs • 63
Required Software • 55 Viewing DNP Binary Inputs • 63
Return Material Authorization (RMA) Policies and Viewing DNP Binary Outputs • 63
Conditions • 120 Viewing DNP Counters • 63
Returning to the Main Menu • 60, 64, 65 Viewing DNP Float Inputs • 63
RS-232 • 91 Viewing DNP Float Outputs • 63
Modem Connection • 92 Viewing DNP Frozen Counters • 63
Null Modem Connection (Hardware Handshaking) Viewing DNP Set Up & Pointers • 57
• 92 Viewing Double Inputs • 60
Null Modem Connection (No Hardware Viewing Float Inputs • 60
Handshaking) • 93 Viewing Master Port Slave Setup • 58
RS-232 Configuration/Debug Port • 89 Viewing Operating Parameters • 57
RS-422 • 93 Viewing Register Pages • 62
RS-485 • 94 Viewing the Error List • 57
RS-485 and RS-422 Tip • 94 Viewing the Next 100 Registers of Data • 62
Viewing the Next 20 Commands • 65
S Viewing the Next 50 Commands • 64
Viewing the Next Page of Commands • 64, 65
Second Byte: • 103 Viewing the Next Page of Data • 60
Sending the Configuration File • 58 Viewing the Previous 100 Registers of Data • 62
Setting Jumpers • 11 Viewing the Previous 20 Commands • 65

November 3, 2008
Index MVI69-DNP ♦ CompactLogix or MicroLogix Platform
Viewing the Previous 50 Commands • 64

Viewing the Previous Page of Commands • 64, 65
Viewing the Previous Page of Data • 60
Viewing Version Information • 58
W
Warm Boot • 86
Warm Booting the Module • 57
What Is Covered By This Warranty • 122, 124
What Is Not Covered By This Warranty • 122
Write Block • 77
Y
Your Feedback Please • 2

November 3, 2008

Mvi69 DNP User Manual

Uploaded by

Copyright:

Available Formats

Mvi69 DNP User Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mvi69 DNP User Manual

Uploaded by

Copyright:

Available Formats

MVI69-DNP

CompactLogix or MicroLogix Platform

Battery Life Advisory

Note: The battery is not user replaceable.

Your Feedback Please

Please Read This Notice 2

Guide to the MVI69-DNP User Manual 7

2 Configuring the MVI69-DNP Module 21

4 Diagnostics and Troubleshooting 53

ProSoft Technology, Inc. Page 5 of 129

5.7 DNP Subset Definition - Slave.............................................................................. 105

6 Support, Service & Warranty 119

Page 6 of 129 ProSoft Technology, Inc.

Guide to the MVI69-DNP User Manual

Verify Communication, → Verifying This section describes how to verify

Reference → Reference (page 69) These sections contain general references

ProSoft Technology, Inc. Page 7 of 129

Page 8 of 129 ProSoft Technology, Inc.

Installing the MVI69-DNP module requires a reasonable working knowledge of

1.1 System Requirements

ProSoft Technology, Inc. Page 9 of 129

1.2 Package Contents

Page 10 of 129 ProSoft Technology, Inc.

1.3 Setting Jumpers

ProSoft Technology, Inc. Page 11 of 129

1.4 Install the Module in the Rack

Page 12 of 129 ProSoft Technology, Inc.

4 Close all DIN rail latches.

ProSoft Technology, Inc. Page 13 of 129

Page 14 of 129 ProSoft Technology, Inc.

1.5 Connect your PC to the Processor

ProSoft Technology, Inc. Page 15 of 129

1.6 Download the Sample Program to the Processor

Page 16 of 129 ProSoft Technology, Inc.

1.6.1 Configuring RSLinx

This action opens the Configure Drivers dialog box.

ProSoft Technology, Inc. Page 17 of 129

Page 18 of 129 ProSoft Technology, Inc.

1.7 Connect your PC to the Module

ProSoft Technology, Inc. Page 19 of 129

Page 20 of 129 ProSoft Technology, Inc.

2 Configuring the MVI69-DNP Module

2.1 Configuration File

2.1.1 Editing the Configuration File

4 In Notepad, open the File menu, and then choose Open

Page 22 of 129 ProSoft Technology, Inc.

2.2 MVI69-DNP Communication Module Configuration

[Section]/Item Value Range Description

ProSoft Technology, Inc. Page 23 of 129

[Section]/Item Value Range Description

Page 24 of 129 ProSoft Technology, Inc.

[Section]/Item Value Range Description

[Section]/Item Value Range Description

[Section]/Item Value Range Description

Page 26 of 129 ProSoft Technology, Inc.

[Section]/Item Value Range Description

[Section]/Item Value Range Description

ProSoft Technology, Inc. Page 27 of 129

[Section]/Item Value Range Description