This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles

for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Designation: D8278 − 19

Standard Specification for

Digital Contact Thermometers for Test Methods Measuring
Flow Properties of Fuels and Lubricants1
This standard is issued under the fixed designation D8278; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.

1. Scope D2983 Test Method for Low-Temperature Viscosity of Au-

1.1 This specification establishes criteria for digital contact tomatic Transmission Fluids, Hydraulic Fluids, and Lubri-
thermometers (DCT) for use in test methods that measure flow cants using a Rotational Viscometer
properties of materials within the scope of Committee D02. D3829 Test Method for Predicting the Borderline Pumping
The DCT criteria are based on the design and sensing charac- Temperature of Engine Oil
teristics of the liquid-in-glass thermometers that are used D4539 Test Method for Filterability of Diesel Fuels by
successfully in Committee D02 test methods. Low-Temperature Flow Test (LTFT)
D4684 Test Method for Determination of Yield Stress and
1.2 The values stated in SI units are to be regarded as
Apparent Viscosity of Engine Oils at Low Temperature
standard. No other units of measurement are included in this
D5481 Test Method for Measuring Apparent Viscosity at
standard.
High-Temperature and High-Shear Rate by Multicell Cap-
1.3 This standard does not purport to address all of the illary Viscometer
--``,`,,``,````,`,`,``,,,,``,```-`-`,,`,,`,`,,`---

safety concerns, if any, associated with its use. It is the D5853 Test Method for Pour Point of Crude Oils
responsibility of the user of this standard to establish appro- D6371 Test Method for Cold Filter Plugging Point of Diesel
priate safety, health, and environmental practices and deter- and Heating Fuels
mine the applicability of regulatory limitations prior to use. D6821 Test Method for Low Temperature Viscosity of Drive
1.4 This international standard was developed in accor- Line Lubricants in a Constant Shear Stress Viscometer
dance with internationally recognized principles on standard- D6896 Test Method for Determination of Yield Stress and
ization established in the Decision on Principles for the Apparent Viscosity of Used Engine Oils at Low Tempera-
Development of International Standards, Guides and Recom- ture
mendations issued by the World Trade Organization Technical D7279 Test Method for Kinematic Viscosity of Transparent
Barriers to Trade (TBT) Committee. and Opaque Liquids by Automated Houillon Viscometer
D7962 Practice for Determination of Minimum Immersion
2. Referenced Documents Depth and Assessment of Temperature Sensor Measure-
2.1 ASTM Standards:2 ment Drift
D97 Test Method for Pour Point of Petroleum Products D8210 Test Method for Automatic Determination of Low-
D445 Test Method for Kinematic Viscosity of Transparent Temperature Viscosity of Automatic Transmission Fluids,
and Opaque Liquids (and Calculation of Dynamic Viscos- Hydraulic Fluids, and Lubricants Using a Rotational
ity) Viscometer
D2162 Practice for Basic Calibration of Master Viscometers E563 Practice for Preparation and Use of an Ice-Point Bath
and Viscosity Oil Standards as a Reference Temperature
D2500 Test Method for Cloud Point of Petroleum Products E644 Test Methods for Testing Industrial Resistance Ther-
and Liquid Fuels mometers
E1750 Guide for Use of Water Triple Point Cells
E2877 Guide for Digital Contact Thermometers
1
This test method is under the jurisdiction of ASTM Committee D02 on 2.2 ISO Standard:3
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of ISO 17025 General requirements for the competence of
Subcommittee D02.07 on Flow Properties.
Current edition approved July 1, 2019. Published July 2019. DOI: 10.1520/ testing and calibration laboratories
D8278-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States

Copyright ASTM International

Provided by IHS Markit under license with ASTM
1Licensee=Enex Chile S.A./5985366001, User=Ruiz, Francisco
No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2020 18:21:44 MDT
 D8278 − 19
3. Terminology variables when measuring the temperature of small static
3.1 Definitions: samples due to differences in temperature probe thermal
3.1.1 digital contact thermometer (DCT), n—an electronic conductivity. Therefore, a DCT that is suitable for use in a
device consisting of a digital display and associated tempera- stirred constant temperature bath will likely result in tempera-
ture sensing probe. ture measurement errors when used to measure the temperature
3.1.1.1 Discussion—This device consists of a temperature of small static sample volumes.
sensor connected to a measuring instrument; this instrument
measures the temperature-dependent quantity of the sensor, 6. DCT Criteria
computes the temperature from the measured quantity, and 6.1 The DCT requirements shown in Table 1 are for various
provides a digital output. This digital output goes to a digital temperature measurement applications used in Subcommittee
display and/or recording device that may be internal or external D02.07 test methods.
to the device. NOTE 1—The DCT’s electronics are typically limited to an environment
3.1.1.2 Discussion—The devices are often referred to as a of 0 °C to 35 °C. A DCT’s temperature limits can be found in its manual
“digital thermometers,” however the term includes devices that or in the manufacturer’s specifications.
sense temperature by means other than being in physical 6.2 DCT Probe Immersion Depth—This criteria quantifies
contact with the media. the length of the DCT probe above the tip that needs to be
3.1.1.3 Discussion—PET is an acronym for portable elec- covered by the material being measured in order to obtain an
tronic thermometers, a subset of digital contact thermometers accurate temperature measurement. Immersing the probe in a
(DCT). material by less than its minimum immersion depth can result
3.1.2 DCT immersion depth, n—depth that a DCT sensor in temperature measurements that significantly differ from
should be immersed in a uniform temperature environment, actual temperature. The error is dependent on the temperature
such that further immersion does not produce a change in difference between the material being measured and surround-
indicated temperature greater than the specified tolerance. ing (ambient) temperature. A test method will set the immer-
3.2 Definitions of Terms Specific to This Standard: sion requirements for the DCT probe.
3.2.1 range-of-use, n—a subset of the nominal DCT tem- 6.3 Measurement Drift—The drift in calibration should be
perature range. checked periodically and at least yearly. This can be accom-
3.2.1.1 Discussion—This is the temperature range over plished using Practice D7962, Practice E563, Test Methods
which a particular DCT is to be used. For example, if a DCT E644, or similar procedure. When the DCT calibration drift
is to be used for viscosity measurements as 40 °C and 100 °C, just exceeds the noted limit for calibration drift, then it is to be
then its “range-of-use” is 60 °C. rechecked within a short period of time but no longer than
month. If the subsequent measurement of DCT calibration drift
4. Summary exceeds the specified limit, it is to be fully recalibrated
4.1 This specification sets the criteria for digital contact consistent with its range-of-use. If the DCT calibration drift
thermometers (DCT) used in measuring flow properties of significantly exceeds the noted limit, then it must be recali-
fuels and lubricants. The DCT criteria were selected so that brated consistent with its range-of-use. See Practice E563, Test
DCT temperature measurements would be essentially the same Methods E644, or Guide E1750 for more information regard-
as those measured using a liquid-in-glass (LiG) thermometer. ing checking calibrations.
For some of the noted test methods, the temperature of a small NOTE 2—For reference temperatures, additional information on prepar-
static sample volume is measured, thus, the difference in ing and using an ice bath can be found in Practice E563. Guide E1750
thermal conductivity between the different types of devices provides guidance for preparing and using a water triple point cell.
will have an impact on measurement equivalence. 6.4 Response Time—Applies to a digital contact thermom-
4.2 The DCT temperature sensing elements noted in this eter’s (DCT) combined display and sensor system. Confor-
specification are platinum resistance temperature (PRT) detec- mance with this requirement is to be provided in the manufac-
tors or thermistors whose sheath or enclosure is in direct turer’s or supplier’s product documentation. Response time is
contact with the substance being measured and are referred to defined as the time for a DCT to respond to 63.2 % step change
as a digital contact thermometers. Both PRTs and thermistors in temperature. The step change begins with the DCT probe at
are members of a group referred to as resistance temperature an initial temperature of 20 °C 6 5 °C air and the timing begins
detectors (RTD) as their resistance is a function of temperature. when it is transferred to water at 77 °C 6 5 °C, which is
flowing at 0.9 m/s 6 0.09 m/s past the sensor, as described in
5. Significance and Use Test Methods E644, or an equivalent method. The DCT display
refresh rate is to be at intervals of every 3 s or less.
5.1 The DCTs meeting the indicated requirements have
been found to be suitable for replacing the liquid-in-glass 6.5 Calibration—When a device is calibrated for the full
thermometers in the noted test methods. The criteria are based nominal temperature range or the “range-of-use” span is 90 °C
on key elements of liquid-in-glass (LiG) thermometers, such as or more, the calibration data should consist of a minimum of
bulb length, immersion depth, measurement precision, and four data points. When the “range-of-use” span is 30 °C or
thermometer positioning. The prescribed dimensions for sensor greater to less than 90 °C, then a minimum of three data points
length, immersion depth, and sheath diameter are critical are sufficient. When the “range-of-use” span is less than 30 °C,
--``,`,,``,````,`,`,``,,,,``,```-`-`,,`,,`,`,,`---

Copyright ASTM International

Provided by IHS Markit under license with ASTM
2Licensee=Enex Chile S.A./5985366001, User=Ruiz, Francisco
No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2020 18:21:44 MDT
 D8278 − 19
TABLE 1 DCT Criteria for D02 Test Methods
NOTE 1—When making measurements below –40 °C with a PRT, it may be necessary to use a 1000 Ω PRT sensor in order to obtain accurate
measurements.
NOTE 2—Additional information on PRT sensors and their testing can be found in Test Methods E644.
D02–DCT ID D02-DCT01 D02-DCT02 D02-DCT03 D02-DCT04
Test Method D97, D2500, D5853 D97, D5853 D97, D2500, D5853 D445
Parameter DCT Criteria

Nominal temperature range,A °C –38 to 50 32 to 127 –80 to 20 –80 to 0

Display resolution, °C minimum 0.1 0.1 0.1 0.01
Accuracy,B °C minimum 0.5 0.5 0.5 0.05
Sensor type (Note 1 and Note 2) PRT, Thermistor PRT, Thermistor PRT PRT
Sensor sheath,C max diameter, mm 4.2D 4.2 4.2D 7
Sensor length,E max mm 10 10 10 25
DCT immersion depth by D7962,F mm (see 6.2) <40 <40 <40 <40
Measurement drift,G less than °C (see 6.3) 0.5 0.5 0.5 0.05
Response time, less than or equal to, seconds 10 10 10 10
(see 6.4)
Calibration data,H (see 6.5) 2 to 4 2 to 4 2 to 4 2 to 4
D02–DCT ID D02-DCT05 D02-DCT06 D02-DCT07 D02-DCT08 D02-DCT11
Test Method D445 D445, D5481 D7279 D2162 D2983
Procedures A, B, C
Parameter DCT Criteria

Nominal temperature range,A °C 0 to 100 100 to 175 0 to 150 10 to 175 –60 to 60 (Note 1)
Display resolution, °C minimum 0.01 0.01 0.01 0.001 0.1
Accuracy,B °C minimum 0.02 0.05 0.02 0.007 0.1
Sensor type (Note 1 and Note 2) PRT, Thermistor PRT PRT, Thermistor PRT PRT
Sensor sheath,C max diameter, mm 7 7 7 7 4.2
Sensor length,E max mm 25 25 18 40 20
DCT immersion depth by D7962,F mm (see <40 <40 <40 <105 <40
6.2)
Measurement drift,G less than °C (see 6.3) 0.02 0.02 0.02 0.01 0.1
Response time, less than or equal to, sec- 10 10 10 10 10
onds (see 6.4)
Calibration data,H (see 6.5) 2 to 4 2 to 4 2 to 4 2 to 4 2 to 4
D02–DCT ID D02-DCT12 D02-DCT13 D02-DCT14 D02-DCT15
Test Method D4539, D6371 D4539, D6371 D3829, D4684, D6821, D8210
D6896
Parameter DCT Criteria

Nominal temperature range,A °C –38 to 50 –80 to 50 –45 to 100 –45 to 60

Display resolution, °C minimum 0.1 0.1 0.1 0.1
Accuracy,B °C minimum 0.5 0.5 0.05 0.1
Sensor type (Note 1 and Note 2) PRT PRT PRT, Thermistor PRT
Sensor sheath,C max diameter, mm 4.2 4.2 3I 1.7
Sensor length,E max mm 10 10 20 20
DCT immersion depth by D7962,F mm (see 6.2) <40 <40 <40 <40
Measurement drift,G less than °C (see 6.3) 0.5 0.5 0.05 0.1
Response time, less than or equal to, seconds 10 10 10 10
(see 6.4)
Calibration data,H (see 6.5) 2 to 4 2 to 4 2 to 4 2 to 4
A
A device’s minimum and maximum temperature may be different than the values shown provided the calibration requirements are met.
B
Accuracy is the combined accuracy of the DCT unit that is the display and sensor without correction factors. See Guide E2877 for more information regarding selecting
a DCT.
C
Sensor sheath is the tube that holds the sensing element. The value is the nominal outside diameter of the sheath segment containing the sensing element. Also see
6.7.
D
Supporting data have been filed at ASTM international headquarters and may be obtained by requesting Research Report RR:D02-1849. Contact ASTM Customer
Service at service@astm.org.
E
The physical length of the temperature sensing element. Contact the DCT supplier to determine whether this parameter is met, as it will not be accessible to the user.
F
DCT probe immersion depth needed for an accurate measurement as determined by Practice D7279 and is to be less than the value in the table.
G
As determined by Practice D7962 or an equivalent procedure.
H
Minimum number of calibration data points used to establish calibration, 6.4.
I
This DCT probe requires the use of a sleeve to hold the probe in good contact with the thermowell wall. Alternatively, a 7 mm glass sheath probe has been found to be
acceptable and no sleeve is required.
--``,`,,``,````,`,`,``,,,,``,```-`-`,,`,,`,`,,`---

then a minimum of two data points are sufficient. The calibra- competency in temperature calibration which is traceable to a
tion data should be distributed over the calibration range and national calibration laboratory or metrology standards body.
included in calibration report. The calibration report should be An example is a calibration laboratory with an ISO 17025
obtained from a calibration laboratory with demonstrated accreditation that includes temperature calibration.

Copyright ASTM International

Provided by IHS Markit under license with ASTM
3Licensee=Enex Chile S.A./5985366001, User=Ruiz, Francisco
No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2020 18:21:44 MDT
 D8278 − 19
6.6 A DCT Certification/Calibration report will include 7. DCT Citation
identification of the temperature reference used for the calibra-
7.1 The DCT citation referencing these criteria in a standard
tion and the date of its last calibration. If the certificate is a
recalibration, the report is to show the AS FOUND values that is to include the D02-DCT designation, any variance from the
were documented before adjustments, and AS LEFT, which are criteria in Table 1, and include the information in subsections
the values documented after adjustments may have been made. 6.2 through 6.6.
If the adjustments to the DCT system cannot be made to correct
its measurements, the report must include correction factors 8. Keywords
needed to bring the display temperature to the correct value 8.1 DCT; digital contact thermometers
along with guidance on applying them.
6.7 DCT Sheath Diameter—The sheath diameters in Table 1
are based on metal sheathed probes. Glass sheathed probes
7 mm OD are suitable alternatives to both 3 mm and 7 mm OD
metal sheathed DCT probes.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
--``,`,,``,````,`,`,``,,,,``,```-`-`,,`,,`,`,,`---

make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/

Copyright ASTM International

Provided by IHS Markit under license with ASTM
4Licensee=Enex Chile S.A./5985366001, User=Ruiz, Francisco
No reproduction or networking permitted without license from IHS Not for Resale, 05/07/2020 18:21:44 MDT