32-1

~~

POWERPLANT
MOUNT. I
CONTENTS 32109000011

CROSSMEMBER . . ...... ... .... ........ .... 8 SERVICE SPECIFICATIONS ........ .. .......3
ENGINE MOUNTING . . . . .. .. . . ... . . . . . .. . .. 4 SPECIAL TOOLS . . . .. .. . .. .. . ... .. . . . . . . ..3

ENGINE ROLL STOPPER, TRANSAXLE MOUNTING ... . ... . . . .. . .. ... . 5

.
. . . .. . .. . . . . . . . . .. 7
CENTERMEMBER .. . .. . .
TROUBLESHOOTING . . .. . . .. . .. . .. .. . .....3
GENERAL INFORMATION . .. . . ... . .. . . .. . .. 2
32-2 POWER PLANT MOUNT - General Information
GENERAL INFORMATION 32100010112

The engine-transaxle mount is of an inertial axis The centermember is bolted to the body and
supporting type. The inertial axis supporting type crossmember, supporting the front and rear roll
mount supports the front upper part of the engine stopper bracket.
at the front and the rear upper part of the transaxle The crossmember is bolted to the body, supporting
at the rear. This arrangementeffectively suppresses the lower arm, steering gear box assembly,
the engine vibration. stabilizer bar, and centermember.

CONSTRUCTION DIAGRAM
Transaxle mount

Rear roll

Centermember Front roll

stopper

00005015
 Service Specification/
POWER PLANT MOUNT - Special Tools/Troubleshooting 32-3
SERVICE SPECIFICATION 32100030071

Item Standard value

Protruding length of stabilizer bar mounting bolt mm (in.) 22 (.9)

SPECIAL TOOLS 32100060094

Tool Application
To support the engine assembly
Engine hanger during removal and installation
of the centermember

I
GENERAL SERVICE General service tool To support the engine assembly
TOOL MZ203827 during removal and installation
Engine lifter of the centermember

TROUBLESHOOTING 32100070011

Symptom 1 Probable cause 1 Remedy I

Excessive engine
wobble or vibFation
1 Cracked rubber parts of insulator 1 Replace

(with engine in
condition)
Insufficientlytightened parts 1 Retighten

Abnormal noise Insufficientlytightened parts Retighten

32-4 POWER PLANT MOUNT - Engine Mounting

ENGINE MOUNTING 32100110324

REMOVAL AND INSTALLATION

Pre-removal Operation Post-installation Operation
(1) Jack up the engine and transaxle assembly until (1) Auto-cruise Vacuum Pump and Bracket Assembly
there is no weight on the engine mount bracket installation (Refer to GROUP 17.)
insulator.
(2) Auto-cruise Vacuum Pump and Bracket Assembly
removal (Refer to GROUP 17.)

98 Nm* AOlMOOOl
72 ft.lbs.*

Removal steps
1. Air conditioning relay box Caution
4AF 2. Air conditioning receiver bracket Mounting locations marked by * should be initially
mounting bolts tightened, and then fully tightened when the body
3. Power steering hose mounting bolt is supporting the full weight of the engine.
4AF 4. Engine mount insulator mounting
bolt
5. Engine mount bracket
A
.( 6. Engine mount stopper
7. Engine mount dynamic damper

REMOVAL SERVICE POINT

4 A b E N G l N E MOUNT INSULATOR MOUNTING BOLT /
AIR CONDITIONING RECEIVER BRACKET
MOUNTING BOLT REMOVAL
(1) To make it easier to remove the engine mount insulator
mounting bolt in vehicles with air-conditioning, remove
the air-conditioning receiver bracket and support the
receiver so that there are no bends in the pipe.
(2) Remove the engine mount insulator mounting bolt.
 POWER PLANT MOUNT - Engine Mountingnransaxle Mounting 32-5
Front side Rear side
INSTALLATION SERVICE POINT
F A + ENGINE MOUNT STOPPER INSTALLATION
(1) At the front, install so that the arrow with the “F” mark
is facing upwards.
(2) At the rear, install so that the arrow with the “R” mark
is facing upwards.

01UD067

INSPECTION 32100120051

0 Check each insulator for cracks or damage.

0 Check each bracket for deformation or damage.

TRANSAXLE MOUNTING 32100140101

REMOVAL AND INSTALLATION

Pre-removal and Post-installation Operation
0 Air Cleaner Assembly Installation and Removal
0 Battery and Battery Tray Removal and Installation

98 Nrn*
72 ft.lbs.*

57 Nm

Removal steps
0 Centermember mounting bolt Caution
Mounting locations marked by * should be
* (Refer to P.32-7.)
1. Transaxle mount bracket
F A 4 2. Transaxle mount stopper
provisionally tightened, and then fully tightened
when the body is supporting the full weight of the
engine.

I TSB Revision .
32-6 POWER PLANT MOUNT - Transaxle Mounting
MZ203827 I . $
A REMOVAL SERVICE POINT
\ , m I1 + A b TRANSAXLE MOUNT BRACKET REMOVAL
(1) Install the special tool to the vehicle body to support
the engine and transaxle assembly.
(2) Remove the centermember mounting bolt.
(3) Remove the bolt and nut of the transaxle mount bracket.
(4) After loweringthe engine and transaxle assembly, remove
4 the transaxle mount bracket.
LX
/ \
MB991453

A01M0002

Engine I, INSTALLATION SERVICE POINT

side bA4TRANSAXLE MOUNT STOPPER INSTALLATION
Clamp the transaxle mount stopper so that the arrow points
in the direction as shown in the diagram.
/-

mount
stopper

Transaxle mount bracket A01R0006

INSPECTlON 32100150043

0 Check each insulator for cracks or damage.

0 Check each bracket for deformation or damage.
 POWER PLANT MOUNT - Enqine Roll Stopper, Centermember 32-7
ENGINE ROLL STOPPER, CENTERMEMBER 32100200090

REMOVAL AND INSTALLATION

52 Nrn*
38 ft.lbs.*

A01M0032

69 Nrn
69 Nrn 51 ftlbs.
51 ft.lbs.

Removal steps
Bolts Caution
Front roll stopper bracket assembly Mounting locations marked by * should be
Rear roll stopper bracket assembly provisionally tightened, and then fully tightened
Bushing (lower) when the body is supporting the full weight of the
Bushing (upper) engine.
Collar
Centermember

INSTALLATION SERVICE POINTS

.A+ REAR ROLL STOPPER BRACKET ASSEMBLY
INSTALLATI0N
Install so that the hole in the rear roll stopper bracket is facing
towards the rear of the vehicle.

c Front of vehicle A01S0002

F B I FRONT ROLL STOPPER BRACKET ASSEMBLY

INSTALLATION
install so that the hole in the front roll stopper bracket is
facing towards the front of the vehicle.

L Cinnt nf tmhi,-lcl An1

 Engine Roll Stopper, Centermember/
32-8 POWER PLANT MOUNT - Crossmember

. L

h .
INSPECTION 32100210031

0 Check each insulator and bushing for cracks or damage.

0 Check each bracket for deformation or damage.

CROSSMEMBER 32100320208

REMOVAL AND INSTALLATION

I
Pre-removal and Post-installation Operation
0 Front Exhaust Pipe Removal and Installation (Refer to GROUP 15.)
0 Centermember Assembly Removal and Installation (Refer to P.32-7.)

22 Nrn

93 - 118 Nm*
67 - 87 ft.lbS.*

88 Nm
2 A01M0143 65 ft.'bs-

Removal steps
1. Self-locking nut <Except 2-DOOR Caution
MODELS-4Gl5> *: Indicates parts which should be temporarily
2. Lateral lower arm mounting bolts tightened, and then fully tightened with the
3. Oil return pipe clamp mounting vehicle on the ground in the unladen condition.
bolts
4. Steering gear and linkage clamp
5. Crossmember assembly
6. Stabilizer bar <Except 2-DOOR
MODELS-4G15>
 POWER PLANT MOUNT - Crossmember 32-9
REMOVAL SERVICE POINT
+ A F CROSSMEMBER ASSEMBLY REMOVAL
(1) Move the crossmemberwhile supporting the steering gear
and linkage in the direction shown by the arrow.

(2) Remove the crossmember while supporting it with a

transmission jack.

-
Approx. 10 mm (.4 in)
INSTALLATION SERVICE POINTS
,A+ STABILIZER BAR INSTALLATION (Except 2-door
models)
Place the identification mark of the stabilizer bar to the left,
and installthe bushing so that the identification mark protrudes
approximately 10 mm (.4 in.) from the edge of the inside
of the bushing.
12M0027

F B + SELF-LOCKING NUT INSTALLATION (Except

2-door models)
Tighten the self-locking nut so that the amount of protrusion
of the end of the stabilizer bar mounting bolts is at the standard
value.
Standard value (A): 22 mm (.9 in.)

INSPECTION 32100330034