LG Dx325 DLP Projector

Internal Use Only
website:http://biz.LGservice.com
DLP PROJECTOR
SERVICE MANUAL
CHASSIS : FM73A
MODEL : DX535 DX535-JD

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
CONTENTS .......................................................................................................2
SAFETY PRECAUTIONS .................................................................................3
REPLACING OF LAMP ....................................................................................4
SPECIFICATIONS.............................................................................................6
ADJUSTMENT INSTRUCTION.........................................................................8
BLOCK DIAGRAM..........................................................................................15
EXPLODED VIEW...........................................................................................16
EXPLODED VIEW PARTS LIST .....................................................................17
REPLACEMENT PARTS LIST........................................................................18
SVC. SHEET .......................................................................................................
PRINTED CIRCUIT BOARD ...............................................................................
Copyright © 2007 LG Electronics. Inc. All right reserved. - 2 - LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An lsolation Transformer should always be used during the Do not use a line Isolation Transformer during this check.
servicing of a receiver whose chassis is not isolated from the AC Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
power line. Use a transformer of adequate power rating as this between a known good earth ground (Water Pipe, Conduit, etc.)
protects the technician from accidents resulting in personal injury and the exposed metallic parts.
from electrical shocks. Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
It will also protect the receiver and it's components from being Reverse plug the AC cord into the AC outlet and repeat AC voltage
damaged by accidental shorts of the circuitary that may be measurements for each esposed metallic part. Any voltage
inadvertently introduced during the service operation. measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
If any fuse (or Fusible Resistor) in this monitor is blown, replace it In case any measurement is out of the limits sepcified, there is
with the specified. possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts. Leakage Current Hot Check circuit
Due to high vacuum and large surface area of picture tube, AC Volt-meter
extreme care should be used in handling the Picture Tube. Do not
lift the Picture tube by it's Neck.
Good Earth Ground

such as WATER PIPE,
Leakage Current Cold Check(Antenna Cold Check) CONDUIT etc.
To Instrument's
With the instrument AC plug removed from AC source, connect an 0.15uF
exposed
electrical jumper across the two AC plug prongs. Place the AC METALLIC PARTS
switch in the on positioin, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone 1.5 Kohm/10W
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
REPLACING OF LAMP
Lamp Replacement
The change interval of lamp may depend on the use environment of Projector. You <Front panel of the Projector>
can see the used lamp time in the CHECKING LAMP TIME section of the Menu
(page.25). You must replace the lamp when:
* The projected image gets darker or starts to deteriorate. Lamp indicators

* The lamp indicator is red.
* The message “Replace the lamp” appears on the screen when turning the
projector on.
Be careful when replacing lamp
- Press the POWER button on the control panel or remote control to turn off power.
- If the operation indicator LED is orange and blinking, do not disconnect the main supply until the operation indicator LED
is lit up constantly (orange).
- Allow the lamp to cool for 1 hour before replacing it.
- Replace only with the same type lamp from an LG Electronics Service Center. Using another manufacturers lamp may
cause damage to the Projector and lamp.
- Pull out the lamp only when replacing the lamp.
- Keep the lamp unit out of reach of children. Keep the Lamp away from heat sources such as radiators, stoves etc.
- To reduce the risk of fire do not expose the lamp to liquids or foreign materials.
- Do not place the lamp near any heat source.
- Make sure the new lamp is securely tightened with screws. If not, the image may be dark or there could be an increased
risk of fire.
- Never touch the lamp unit glass otherwise image quality may be compromised or lamp life maybe reduced.
To obtain a replacement Lamp unit
Lamp model number is on page 37. Check the lamp model and then purchase it from an LG Electronics Service Center.
Using another manufacturers lamp may cause damage to the projector.
Lamp unit disposal
Dispose of the used lamp by returning it to the LG Electronics Service Center.
Replacing the Lamp
1 Turn off the projector and unplug the power cable.

Carefully place on a cushioned surface. 2 Unscrew the screw from the lamp cover using a
screwdriver.
(Allow the lamp to cool for 1 hour before

removing the used lamp from the projector.)
Lamp case screw
After lifting the lamp cover off, remove the two
3 retaining screws on the lamp case with a screw-

driver. 4 Lift the lamp up from the projector.
Knob
Screws
5 Pull out the handle slowly and remove the lamp

case. 6 Insert the new lamp gently into the correct position.
Make sure it is inserted correctly.
Close the lamp cover and install the screws from

7 Tighten the screws you removed in step 3. 8 step 2 to install the cover.
(Make sure they are fixed firmly.) (If the lamp cover is not installed correctly the unit will not
power on.)
Using another manufacturers lamp may cause damage to the projector or lamp.
Make sure the lamp cover is securely fastened. If the lamp cover is not installed correctly the unit will not power on.
If this fault persists contact an LG Authorized Service Center.
SPECIFICATIONS
NOTE: Specifications and others are subject to change without notice for improvement.
A Scope
This standard can be applied to the DLP Projector related to FM73A Chassis.
A Test Condition
1) Temperature: 25°C±5°C (Only CST is 40°C ± 2°C )
2) Relative Humidity: 65±10%
3) Power Voltage: Standard input voltage (100-240V~, 50/60Hz)
4) Use the parts only designated in B.O.M.,PARTS SPEC.,or drawings.
5) Follow each drawing or spec for spec and performance of parts,based upon P/N of B.O.M
6) Warm up TV set for more than 30min. before the measurement.
A Test and Inspection Method

1) Performance: Follow the Standard of LG TV test
2) RCA JACK performance: Follow the standard of LG
3) Standards of extra requirement
SAFETY: CB (EN55013),
Electric wave: CE (EN55020)
A General Specification
Specification
No. Item Remark
Min Typ Max Unit
1 Video input applicable system 1) NTSC M 3.579545 / 60Hz

2) NTSC 4.43 4.433618 / 60Hz
3) PAL 4.433618 / 50Hz
4) PAL M 3.575611 / 60Hz
5) PAL N 3.582056 / 50Hz
6) SECAM 4.286 / 50Hz
7) NTSC-PB 4.433618 / 60Hz
2 Power SMPS
3 Input Voltage 100V(-10%) - 240(+6%)V~, 50/60Hz
4 Market World wide
5 Screen size 4:3
6 Aspect ratio 4:3
7 Operating Temperature 0 40 deg
8 Operating Humidity 75 %
9 Storage Temperature -20 60 deg
10 Storage Humidity 85 %
A Feature and Function
Specification
No. Item Remark
Min Typ Max Unit
1 REMOCON NEC Code LGE key

2 DVI_D Input 1 Digital RGB
3 RGB Input 1 Separate D-Sub 15 pin
4 RGB Output 1 Separate
5 Component input 1 Y, PB, PR D-Sub 15 pin
480i, 480p, 720p, 1080i, 576i,576p Through RCA to D-Sub Gender
6 Composite input 1 480i, 576i RCA Jack(Yellow)
7 S-video input 1 480i,576i S-VIDEO jack
8 USB Port 1 USB jack(only for download)
9 RS-232C Port 1 Control the SET w/PC
10 Local Key MENU, SOURCE, AUTO, A OK, /(KEYSTONE+),
0(KEYSTONE-), <, >, Power
11 Display mode 4:3 & 16:9
12 Sound No
13 OSD Language Korean/ English/ Deutsch/ Italiano/ Espanol/
Chinese/ French/ Portugal/ Svenska/ Polish
14 Source RGB(Component)/ DVI/ Video/ S-Video
15 APC Clear/ Soft/ User Video/ S-Video/ Component
16 Contrast 0 100
17 Brightness 0 100
18 Sharpness 0 100
19 Color 0 100 Video/ S-Video/ Component
20 Tint R50 G50 Video/ S-Video/ Component
21 Color R 0 100 RGB/DVI
22 Color G 0 100 RGB/DVI
ADJUSTMENT INSTRUCTION
1. Application Object 3) Turn screw (A) up / down adjustment to the right / left
and mark where the image is aligned. Fix the
This instruction is for the application to the DLP Projector adjustment screw in position.
(Chassis: FM73A).
2. Notes
(1) The power source insulation of this DLP Projector is not
charging type and you may not use the transformer for Step 1 Step 2 Step 3
insulation. It is advised to use an insulation transform
between the power supply cable and power input of the set <Fig. 2> Illuminator Up / Down Adjustment Sequence
to protect the test equipment.
(2) The adjustment must be performed under the correct
sequence. (2) Left and Right Adjustment 1
(3) The adjustment must be performed in the circumstance of 1) Turn screw (B)Left / Right adjustment to the right and
25±5°C of temperature and 65±10% of relative humidity. mark where the image is aligned.
(4) The set must be on for 5 minutes prior to any adjustment. 2) Turn screw (B) Left / Right adjustment to the left and
mark where the image is aligned.
3) Turn screw (B)Left / Right adjustment to the right / left
3. Composition of Adjustment Mode adjustment screw in position.
(1) Select ‘Video mode’ as input source.

(2) Pressing the adjust key on the service remote will open or
close the service menu.
(3) Press the ADJ key to exit the service menu.
(4) Preparation for Adjustment
1) Power is connected in set to be power on. Step 1 Step 2 Step 3
2) Do heat run 5minutes.
<Fig. 3> Illuminator Left/Right Adjustment Sequence 1
(3) Left and Right Adjustment 2

4. Folding Mirror Adjustment 1) Turn screw (C)up / down adjustment to the right and
Top and bottom 2) Turn screw (C) up / down adjustment to the left and
adjustment screw A mark where the image is aligned.
3) Turn screw (C)up / down adjustment to the right / left
adjustment screw in position.
Left and right

adjustment screw C
Left and right

adjustment screw B Step 1 Step 2 Step 3
<Fig. 1> Illuminator Adjustment Part by Folding Mirror <Fig. 4> Illuminator Left/Right Adjustment Sequence 2
4-1. Illuminator Adjustment Sequence (4) Final Adjustment

After putting optical engine on JIG, check the mirror part. Fix the adjustment screw in position. (1), (2), (3)
Check the full white screen and make adjustments in the adjustment twice and find the optimum position. Check the
following sequence. image with the naked eye for optimum alignment.
(1) Up and Down Adjustment

1) Turn screw (A) up / down adjustment to the right and
2) Turn screw (A) up / down adjustment to the left and
4-2. Illuminator Phenomenon Adjustment
Illuminator goes down direction Illuminator goes down area
Adjustment Screw Screen state

Description
part direction Initial state State after adjusting
Right At first, upside illuminator goes down

(tighten and right illuminator also goes down in
direction) detail.
Up/down
screw A
Left At first, downside illuminator goes

(loosen down and left illuminator also goes
direction) down.
Right
At first, left illuminator goes down and
(tighten
downside illuminator also goes down.
direction)
left/right
screw B
Left
At first, right illuminator goes down and
(loosen
upside illuminator also goes down.
direction)
Right
At first, left illuminator goes down and
(tighten
downside illuminator also goes down.
direction)
left/right
screw C
Left
At first, right illuminator goes down and
(loosen
upside illuminator also goes down.
direction)
4-3. Coherent Light Source Adjustment

(1) Coherent light source specification [ Do not tilt the optical axis adjustment to improve the
: 50% of center black brightness coherent light source
(Refer to product specification)
==> Same specification applied for coherent light source
of <Fig. 5> type
(2) Optical axis
: Adjust so that it is set at the center.
<Fig. 5> Coherent Light Source
5. Caution for DMD 7. Check the EDID
(Digital Micro-mirror Device) (1) Configure the equipment same to <Fig. 6>.
(2) Select [Read Data & Verify] of the DDC record S/W.
5-1. Caution for DMD ESD - Be sure that it is not [Write Data & Verify] of the substrate
(1) Connector the grounding to prevent a damage of ESD adjustment.
(Electrostatic Discharge) when handing the DMD.
(2) Wear a wrist strap to connect the ESD grounding in flesh (3) Make sure that the OK signal and the checksum are equal
necessarily. to the values given at the record file.
(3) Connect the ESD ground to workstation and an electric - Because it is the process to read and check the EDID, it
conductor. is not necessary to release the EDID Write Protection.
(4) Save the DMD after getting rid of a static electricity. Keep
it at an exclusive case when moving it When grounding,
open the case.
(5) Put on gloves for preventing static electricity. 8. RGB Offset/Gain Adjustment
(6) All work is done at static free location. Attach the tape or
remove a dust on the DMD front or DMD back pin 8-1. Required Test Equipment
(1) Pattern Generator 1EA(Analog RGB)
5-2. Caution for DMD Clean (2) Remote control 1EA
(1) Follow the procedure and caution to prevent the screen
from being scratched. 8-2. Setting of the Device
(2) When DMD glass stains with dust, polish the front and Set the equipment as <Fig. 7>.
back DMD glass with soft cloth. Then, do it again after
rotating 180 degree the DMD. If necessary, keep under RGB PC Pattern
SCREEN Projector
observation. Generator
(3) Don’t clean the DMD with the high pressure. The static
electricity and pressure will damage the DMD.
<Fig. 7> Device Setting Diagram for RGB offset/gain
Adjustment
6. EDID Data input

6-1. Required Test Equipment 8-3. Preparation for Adjustment
(1) PC, DDC adjustment Jig(PC serial to D-sub connection (1) Connect the Pattern Generator as shown at <Fig. 6>
machinery) Device Setting Diagram.
(2) DDC record S/W (EDID Data Write & Read) (2) Set the output of the Pattern Generator to XGA 60Hz.
(3) D-sub terminal, DVI_D (1024 X 768 60Hz)
(3) Press the ‘Select Input’ key to select the RGB input.
6-2. Preparation for Adjustment & Setting
of the device 8-4. Sequence of Adjustment
(1) Set like <Fig. 6>, PC and JIG (It is entered into No. 99 pattern (pattern created: OPT->
(2) Press “FRONT-AV” key of the adjustment remote 199.127.0.16.240))
controller to release EDID Write Protection.
(3) Practice of DDC record S/W(EDID Data Write & Read) (1) Select the ‘white/black pattern’ of <Fig. 8> as the pattern
(4) Make sure that the OK signal and the checksum are equal of Pattern Generator. (XGA 60Hz)
to the values given at the record file.
(5) When any fail is occurred at the DDC record S/W, because
the EDID Write Protection may not be released, perform
(2) ~ (4) again.
DLP PJTR SET

PC
JIG <Fig. 8> White/Black Pattern
<Fig. 6> Device setting diagram for EDID data input (2) Select ADJ -> 2. RGB Gain/Offset -> A (Enter) -> G (Vol+)
at the adjustment remote controller.
(The actual adjustment is automatically performed by the
system Micom.)
9. COMPONENT Offset/Gain 11-2. Required Test Equipment
(1) Illuminometer (Model : CL-200) 1EA : Chromaticity
Adjustment measurement from projection screen center.
(1) Select the ‘75% Color bar pattern(No. 67)’ of <Fig. 9> as (2) Set fixing device 1EA
the pattern of Pattern Generator. (3) Remote control 1EA
(Resolution: component 720p)
11-3. Preparation for Adjustment
(1) Connect the power cord and turn the set on, then connect
PC or Pattern to PC input.
(2) Select Adjust -> CWI -> A (Enter) -> A (Enter) at the
adjustment remote controller. (Default value : 350)
(3) After entering into the CWI, press A ENTER key at the
adjustment remote controller to switch to the Full Red
screen as shown at <Fig. 11>. At this time, read X and Y
values at the center, the color coordinates of the
illuminometer.
Colow wheel index

CWI = 350
<Fig. 9> 75% Color Bar
(2) Select ADJ -> 3. Component Gain/Offset -> A (Enter) -> G

(Vol+) at the adjustment remote controller.
(The actual adjustment is automatically performed by the
system Micom.)
<Fig. 11> Full RED Pattern

10. CWI/White Balance Measurement
Condition 11-4. Adjustment
(1) CWI and White Balance is adjusted using the measurement of (1) Adjust CWI to the left/right value by using the volume
color coordinate. So periodically adjust within time set and you buttons at the first adjustment value is preset to 350.
should provide the replacement equipment to use the (2) Illuminometer color coordinates is changed when pressing
correction. volume button.
(2) Adjust the screen size to a minimum of 40 inches. (3) X coordinates usually get maximum value at
(3) Place the CL-200 on the center of projection screen. X=0.630±0.02 and Y coordinates usually get minimum
(4) Make the measurement condition under 1Lux for CL-200 value at Y=0.350±0.02. Adjust this value by pressing
to measure the correct color coordinate. volume button on the remote control. Average value is 350.
(4) Check the red pattern whether it is entirely uniform.
When there is no problem after checking, press ‘EXIT’ key
at the adjustment remote controller to exit.
11. CWI Adjustment
11-1. Setting of the Device
Set the equipment as <Fig. 10>.
Illuminometer
Equipment to monitor Lx,X,Y data
Set
Set fixing device
<Fig. 10> Device Setting Diagram for CWI Adjustment
12. White Balance Adjustment 13. Measuring the Projector Brightness
12-1. Required Test Equipment 13-1. Preparation for Adjustment
(1) Illuminometer (Model : CL-200) 1EA : Chromaticity (1) Set Setting
measurement from projection screen center - Input source: Default(not necessary to specify the source)
(2) Pattern Generator (RGB input, XGA(1024 X 768) 60Hz)
(3) Set fixing device 1EA (2) Measuring the Brightness
(4) Remote control 1EA - Remote control: Adj > optic check > White
12-2. Equipment Composition 13-2. Configuring the Projector Brightness

Use the RS232C cable to connect the set and the CL200 as Measuring JIG Software
shown at <Fig. 12> Device Setting Diagram. (1) Select the Model: DX535-JD
(2) Screen Size: W: 813, H: 610
Illuminometer (3) Examination
Equipment to monitor Lx,X,Y data (3) Examination (2) Screen Size
(1) Select Model

Set
Set fixing device
<Fig. 12> Device Setting Diagram
12-3. Adjustment
(1) Select ADJ -> 5. White Balance -> G (Vol +) at the
adjustment remote controller. <Fig. 13> Configuring the Brightness Measuring JIG Software
(2) The White Balance adjustment is automatically started.
(3) Check “Success” message after about 15 seconds.
(4) When “Fail” message is displayed, perform (2) ~ (4) again.
(5) Check the Warm adjustment and the Cool adjustment by 13-3. Setting the Brightness Measuring Screen
selecting ADJ -> 5. White Balance -> A (Enter) at the Screen size setting
adjustment remote controller, select ‘Normal’, and exit. - Correctly set to the screen size by model as shown at <Fig.
14>.
(Set to the measuring screen size and adjust it with no tilt of
the screen.)
<Fig. 14> Configuring the Brightness Measuring JIG
<Fig. 15> Brightness Measuring Screen Size
14. EDID Data
3.3V ADDR[3:0], MODE[1:0]
5V TPS3307
SEL[1:0], OEZ, STRB 12V, 3.3V MBRST [0:15]
2.5V DAD 1000
DRCG REFCLK, DRCGPDZ 10 16
13 V POWER DMD
PCLKM, SCLKN POSENSE
(CDCR83) 0.7
12 CTM, CTMN D_AN[00:15] DDR 768P(XGA)
PIN 3.3V, 2.5V, 1.5V D_AP[00:15] 32
D_BN[00:15] DDR
1.8V, 2.5V RD_RQ [0:7] / DQB[0:7] / DQA[0:7] D_BP[00:15]
RDRAM 32

Option(Sub)
(K4R271669F) 24
DDRCLK, SCRTL,
(128Mbit)
3.3V 12V, 5V CW_CTR
Wireless EEPROM
(AT24C16AN) MTR_CSZ, MTR_CLK CWY1
Module IIC_1
MTR_DATA A8904 CWY2
(16Kbit)
CWY3
Color
3.3V FLASH PMADR [0:20] / PMDAT[0:15]
Wheel
(AM29BV162A)
Copyright © 2007 LG Electronics. Inc. All right reserved.

39 CW_INDEX
(16Mbit)
LAMP_EN
AC
Ballast
230W
LAMP_LIT
3.3V R[0:7] G[0:7] B[0:7]
RGB_OUT Buffer
- 15 -
RGB_PC ADC 24 TEMP_LED2, LAMP_LED1, OP_LED0
HS/VS, CLK, DE, FIELD DDP 2000
5V EEPROM (MST3361M)
(EDID) 6 LED
AT24C02BN M_IIC
DVI_I & KEY
KEY_OUT 0, KEY_OUT 1, KEY_OUT 2
Pad
5V EEPROM
Y[0:7], C[0:7] 6 15P
(HDCP)
BLOCK DIAGRAM
AT24C02BN
3.3V, 2.5V
CVBS 16
DECODER HS/VS, CLK, DE, FIELD
(TW9919)
S_VIDEO
FRONT IR : IR_1
M_IIC Remote
IR_0 Control
KSM-603
3.3V SDRAM
A[0:11] ,D[0:15]
(HY57V641620ETP)
CASE_DET
28 Case
USB_D_N, USB_D_P, USB_ENZ Detect
USB
(SVC only)
TEMP_SENSOR TEMP
SENSOR
RS-232C UART0-RX/TX, UART-CTSZ/RTSZ
X2
6P 7466_EN 3.3V
ADT7466 DRIVE, TACH FAN
DEBUGGING M_IIC IIC_1 X2 X4
LGE Internal Use Only

EXPLODED VIEW
410
510
500
107
104
105
106
102 103
590
420
580 510
581 401
600
571 400 520
402
601
611
570 101
572
610
530
A2
310
301
300
EXPLODED VIEW PARTS LIST
No. Part No. Description
101 EAL35004602 Fan Module,D09A-12PH 2.4KRPM DC 12V 90MA 1.08W 60HZ 1M3
102 4810V01044C Bracket,PRESS SECC T0.8 DUCT AH115P-JD FM71-A SECC(EGI) DMD
103 EAL35002802 Fan Module,D08A-12PG 2.8KRPM DC 12V 90A 1.08W 60HZ 900MM3
104 4810V01056N Bracket,COMPLEX FAN DX535-JD FM73A EGI DMD
105 MJH32379201 Supporter,PRESS SECC 0.5mm NON SECC(EGI) 80 Fan Supporter Modify
106 EAL35002801 Fan Module,D08A-12PH 2.4KRPM DC 12V 90MA 1.08W 60HZ 900MM3
107 4811V00348E Bracket Assembly,FAN DX535-JD FM73A POWER
300 ABQ32155702 Case Assembly,FM73A DX535-JD.AEULLAX TOP
301 AGU32157002 Plate Assembly,DECO DX535 LENS
310 5020V00941F Button,COMPLEX CONTROL DX535-JD ABS, AF-303S 6KEY ASSY DDM SILVER(117A)
400 ABQ32150001 Case Assembly,FM71A AH115P-JD.ABGLLAX BASIC
401 ACQ32150101 Cover Assembly,AH115P FM71A ETC BOTTOM
402 MFA32548601 Leg,MOLD NYLON 66 NON AH115 PC FRONT
410 ACQ33706201 Cover Assembly,Rear DX535-JD FM73A 100 AV BRACKET ASSY
420 ABA32155801 Bracket Assembly,DUCT AH115P-JD FM71-A LAMP OUT
500 EBR37289901 PCB Assembly,Main FM73A DX535 - -
510 EBR33660102 Auto SMT PCB Assembly,SUB A.I FM71A AH115P-JD - Temp Auto Insert
520 EBT33659302 Chassis Assembly,SUB FM711 AH115-JD IR PCB Assembly
530 EBT33658303 Chassis Assembly,SUB FM73A Control and LED
570 EAY30238704 Ballast,PHG201A1CM 230W NSHA230W 164mm/50mm/90mm AC OUTTRIGGER
571 MGJ32378201 Plate,Shield PRESS SPTE-C 0.5mm SHIELD SPTE Ballast Sheld
572 EBT38022201 Chassis Assembly,SUB FM73A DX535-JD BALLAST ASSY
580 EAY38700401 SMPS,AC/DC B12-L092B 90VTO264V 300W 50/60 CB/UL etc... DX535(H&E)Projector Power -
581 MGJ32377901 Plate,Shield PRESS AL 1.0mm SHIELD AL Power Shield
590 EAY32936801 SMPS,AC/DC B12-L091A 90VTO264V 300W 50/60 CB/UL etc... AH115(H&E) Projector Power
600 31419EN029C Chassis Assembly,ENGINE FM73A DX535-JD
601 MBN32373201 Case,PRESS SECC 1.0 BOTTOM AH115 SECC(EGI) AH115 model Lamp Case cover
610 ACQ32159702 Cover Assembly,DX535-JD FM73A 100 LAMP AC230W
611 6912B22008D Lamp,Mercury NSHA230LG 230W 70VDC 2.40A 5.9KLM 0LUX WHITE USHIO
A2 6710V00133V Remote Controller,COMPLEX FM73A DX535 DATA LASER
REPLACEMENT PARTS LIST
RUN DATE : 2007.8.9
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION
Q103 0TR387500AA 2SC3875S(ALY) NPN 5V 60V 50V

IC
IC01 0IZZVG0003B S1076-7408 IQ8 TEXAS
IC101 0IMCRSG010A ST3232CDR 3VTO5.5V - S
Q305 0TR102009AJ KRC102S NPN 30V 0V 50V 100MA
IC200 0IPMG00037A KIA78D25F 3.2TO10V 2.5
Q700 0TFON80011A FET,NTR1P02LT1G
IC201 EAN32662801 KA7809ERTM 35V to 40V
IC202 0ISTLON023B NL17SZ126DFT2G 1.65TO5
IC204 0IMMRAL014D AT24C02BN-SH-T 2KBIT 2
Q704 0TR150400BA 2SA1504S(ASY) PNP -5V -50V -5
Q900 0TFRH80001A FET,RK7002T116
IC207 0IPRPBB005A OPA3692IDBQ 12V_+-6V 4
IC209 0IPRP00696C MST3361M-LF-170 3.3V_2
IC210 0IMMRCS012B CAT24C08W-T(MST3000) 8
Q902 0TFON80011A FET,NTR1P02LT1G
IC300 0IPMG00049A AZ1117H-1.8TR/E1[H13A]
Q903 0TFRH80001A FET,RK7002T116
IC302 0IPRP00630C TW9910DANA2-GR 3.15VTO
IC40 0IMCRSH003A GP2S40 6V 35V - 50MA 1
IC400 0IMCRTI029B DDP2000 5V 65NM DLP IM
IC401 0IMMR00115A MX29LV160CBTC-70G(MA)
IC600 0IMCRAL006A AT24C16AN-10SU-2.7 16K DIODE
IC601 0IMCRSG008A 74LX1G14CTR 1.65TO5.5V
D200 EAH33945901 CDS3C30GTH 30V 50V 120
IC602 0IPMG00049A AZ1117H-1.8TR/E1[H13A]
D201 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
IC603 0IMCRTI014A CDCR83 3.135VTO3.465V
D202 EAH33945901 CDS3C30GTH 30V 50V 120
IC604 EAN37392701 K4R271669H-DCS8 128MBI
D203 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
IC700 0IMCRTI033A TPS3307-25D 2TO6V 2.5V
D204 EAH33945901 CDS3C30GTH 30V 50V 120
IC702 0IPMG78383A KIA78R033F 4.3TO12V 3.
D205 EAH33945901 CDS3C30GTH 30V 50V 120
IC703 EAN35245001 KIA78R25F 4.2V~35V 2.5
D206 EAH33945901 CDS3C30GTH 30V 50V 120
IC704 0IMCRMZ001A MP1583DN-Z,LF 4.75TO23
D206 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
IC706 0IMI623200B M62320FP(SOP) 4.5TO5.5
D207 EAH33945901 CDS3C30GTH 30V 50V 120
IC756 0IMCRTI012B 2503253-0003(DAD1000-3
D208 EAH33945901 CDS3C30GTH 30V 50V 120
IC800 0IMCRAG001A A8904SLP 4.5TO5.5V 4TO
D208 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
IC801 0IMCRSG008A 74LX1G14CTR 1.65TO5.5V
D209 EAH33945901 CDS3C30GTH 30V 50V 120
IC802 0ISH121100D PQ12DZ1U 6TO16V 12V 8W
D209 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
IC803 0IMCRFA003A KA2903D 2TO36V +-1TO18
D210 EAH33945901 CDS3C30GTH 30V 50V 120
IC900 0IMCRMZ001A MP1583DN-Z,LF 4.75TO23
D210 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
IC901 0IPRP00631A ADT7466ARQZ-REEL7,LF 3
D211 EAH33945901 CDS3C30GTH 30V 50V 120
IC902 0IPRPSH001A PQ20WZ1U 4TO10V 20V 8W
D211 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
D212 0DD184009AA KDS184 KDS184 TP KEC -
IC904 0IPRP00631A ADT7466ARQZ-REEL7,LF 3
D213 0DRSE00048A RLCAMP0504M 1.2V 6V 25
D214 0DRSE00048A RLCAMP0504M 1.2V 6V 25
D700 0DRDI00028B B350A 700MV 50V 3A - 2
TRANSISTOR D701 EAH33946001 CDS3C05GTA 5.6V 6.4V 1

D702 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
D703 EAH33946001 CDS3C05GTA 5.6V 6.4V 1
D751 0DRGS00328A SS26 700MV 60V 2A - -
D752 0DRGS00328A SS26 700MV 60V 2A - -
D800 0DRON00088A BAT54SWT1 800MV 30V 20 C207 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V
D801 0DRON00088A BAT54SWT1 800MV 30V 20 C208 0CK104BF56A C1005X7R104KET 100nF 10% 16V
D901 0DRDI00028B B350A 700MV 50V 3A - 2 C211 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
D901 0DL233309AC LED,Chip SAM2333 RED/Y-GREEN 2. C212 0CK104BF56A C1005X7R104KET 100nF 10% 16V
D902 0DL233309AC LED,Chip SAM2333 RED/Y-GREEN 2. C213 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
D903 0DL233309AC LED,Chip SAM2333 RED/Y-GREEN 2. C214 0CK104BF56A C1005X7R104KET 100nF 10% 16V
D912 0DLRH0288AA LED,Chip SML-512UW RED 2V 30mA C215 0CK104BF56A C1005X7R104KET 100nF 10% 16V
ZD100 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C216 0CK471CK56A C1608X7R1H471KT 470pF 10% 50V
ZD101 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C217 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
ZD102 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C218 0CK471CK56A C1608X7R1H471KT 470pF 10% 50V
ZD103 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C219 0CK103CK56A 0603B103K500CT 10nF 10% 50V X
ZD300 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C222 0CE227SC6DC VMV227M6R3S0ANE010 220uF 20%
ZD301 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C222 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
ZD701 0DZRM00178A Zener,UDZS5.1B 5.1V 4.98TO5. C225 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
ZD751 0DZVH00118A Zener,GZF8V2C 8.2V 7.7TO8.7V C226 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C227 0CK104CF56A 0603B104K160CT 100nF 10% 16V
CAPACITOR
C227 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C100 0CK104CF56A 0603B104K160CT 100nF 10% 16V C228 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C101 0CZZTAT008D RVS-6V470MU-R 47uF 20% 6.3V 3 C229 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C102 0CZZTAT008D RVS-6V470MU-R 47uF 20% 6.3V 3 C230 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
C103 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V C231 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C104 0CK104CF56A 0603B104K160CT 100nF 10% 16V C232 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
C105 0CK104CF56A 0603B104K160CT 100nF 10% 16V C233 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
C106 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C233 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C106 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C234 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
C107 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C234 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C107 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C235 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
C108 0CK104CF56A 0603B104K160CT 100nF 10% 16V C235 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C113 0CK105CF94A 0603F105Z160CT 1uF -20TO+80% C238 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
C115 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V C239 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
C126 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V C240 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
C200 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V C240 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C201 0CK104BF56A C1005X7R104KET 100nF 10% 16V C241 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C205 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V C245 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C253 0CE227SC6DC VMV227M6R3S0ANE010 220uF 20% C317 0CC220CK41A C1608C0G1H220JT 22pF 5% 50V C
C254 0CE227SC6DC VMV227M6R3S0ANE010 220uF 20% C318 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C255 0CE227SC6DC VMV227M6R3S0ANE010 220uF 20% C319 0CC220CK41A C1608C0G1H220JT 22pF 5% 50V C
C258 EAE32166101 CS1005XR473K250CR 0.047uF 10% C322 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C260 0CK153CK56A 0603B153K500CT 15nF 10% 50V X C40 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C261 EAE32166101 CS1005XR473K250CR 0.047uF 10% C400 0CK226FF67A EMK325BJ226MM-T 22uF 20% 16V
C262 EAE32166101 CS1005XR473K250CR 0.047uF 10% C401 0CK226FF67A EMK325BJ226MM-T 22uF 20% 16V
C268 0CC220CK41A C1608C0G1H220JT 22pF 5% 50V C C407 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C283 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16 C422 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C300 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V C428 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C438 0CK104BF56A C1005X7R104KET 100nF 10% 16V C620 0CC680CK41A C1608C0G1H680JT 68pF 5% 50V C
C445 0CK104BF56A C1005X7R104KET 100nF 10% 16V C626 0CC050CK11A C1608C0G1H050DT 5pF 0.5PF 50V
C453 0CK104BF56A C1005X7R104KET 100nF 10% 16V C631 0CK226FF67A EMK325BJ226MM-T 22uF 20% 16V
C455 0CHZB00107A 6TPC100M 100uF - 6.3V - - 734 C633 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
C455 0CHZB00107A 6TPC100M 100uF - 6.3V - - 734 C634 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C456 0CK104BF56A C1005X7R104KET 100nF 10% 16V C635 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
C458 0CHZB00107A 6TPC100M 100uF - 6.3V - - 734 C637 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C508 0CK103BH56A C1005X7R1E103KT- 10nF 10% 25V C646 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C610 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C657 0CK104BF56A C1005X7R104KET 100nF 10% 16V
C611 0CK104BF56A C1005X7R104KET 100nF 10% 16V C700 0CK104CK56A 0603B104K500CT 100nF 10% 50V
C614 0CHZB00107A 6TPC100M 100uF - 6.3V - - 734 C703 0CC221BKFAA C1005C0G1H221JT 220pF 5% 50V
C616 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V C704 0CC221BKFAA C1005C0G1H221JT 220pF 5% 50V
C617 0CK104BF56A C1005X7R104KET 100nF 10% 16V C704 0CC221BKFAA C1005C0G1H221JT 220pF 5% 50V
C619 0CC680CK41A C1608C0G1H680JT 68pF 5% 50V C C705 0CC221BKFAA C1005C0G1H221JT 220pF 5% 50V
C705 0CC221BKFAA C1005C0G1H221JT 220pF 5% 50V C776 0CK104CK56A 0603B104K500CT 100nF 10% 50V
C705 0CK104CK56A 0603B104K500CT 100nF 10% 50V C777 0CK104CK56A 0603B104K500CT 100nF 10% 50V
C706 0CC221BKFAA C1005C0G1H221JT 220pF 5% 50V C778 0CK335FK66A C3225X7R1H335MT 3.3uF 20% 50V
C707 0CK104CF56A 0603B104K160CT 100nF 10% 16V C780 0CK104CK56A 0603B104K500CT 100nF 10% 50V
C708 0CH2474F566 0805B474K160CT 470nF 10% 16V C782 0CZZTCT006C C3225Y5V1E106ZT 10uF -20TO+80
C709 0CHZB00107A 6TPC100M 100uF - 6.3V - - 734 C785 0CK106EF56A C3216X7R1C106KT 10uF 10% 16V
C711 0CK222CK56A 0603B222K500CT 2.2nF 10% 50V C786 0CE226WF6DC MVK5.0TP16VC22M 22uF 20% 16V
C713 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C788 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C713 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V C789 0CE226WF6DC MVK5.0TP16VC22M 22uF 20% 16V
C715 0CK104CF56A 0603B104K160CT 100nF 10% 16V C802 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C718 0CK104CF56A 0603B104K160CT 100nF 10% 16V C804 0CE476WH6DC MVK8.0TP25VC47M 47uF 20% 25V
C719 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16 C804 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V
C720 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16 C805 0CC391CK41A C1608C0G1H391JT 390pF 5% 50V
C721 0CK226FF67A EMK325BJ226MM-T 22uF 20% 16V C807 0CK272CK46A 0603B272J500CT 2.7nF 10% 50V
C721 0CK226FF67A EMK325BJ226MM-T 22uF 20% 16V C808 0CK272CK46A 0603B272J500CT 2.7nF 10% 50V
C724 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V C809 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C726 0CK103CK56A 0603B103K500CT 10nF 10% 50V X C810 0CK472CK56A 0603B472K500CT 4.7nF 10% 50V
C727 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V C811 0CE105WK6DC MVK4.0TP50VC1M 1uF 20% 50V 5.
C751 0CE226SF6DC VMV226M016S0ANB010 22uF 20% 1 C812 0CC102CK41A C1608C0G1H102JT 1nF 5% 50V C0
C752 0CK104CK56A 0603B104K500CT 100nF 10% 50V C813 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C752 0CK104CK56A 0603B104K500CT 100nF 10% 50V C814 0CC102CK41A C1608C0G1H102JT 1nF 5% 50V C0
C753 0CK104CK56A 0603B104K500CT 100nF 10% 50V C816 0CE476WH6DC MVK8.0TP25VC47M 47uF 20% 25V
C754 0CK104CK56A 0603B104K500CT 100nF 10% 50V C816 0CK103CK56A 0603B103K500CT 10nF 10% 50V X
C755 0CK104CK56A 0603B104K500CT 100nF 10% 50V C817 0CC102CK41A C1608C0G1H102JT 1nF 5% 50V C0
C756 0CK104CK56A 0603B104K500CT 100nF 10% 50V C818 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V
C757 0CK104CK56A 0603B104K500CT 100nF 10% 50V C818 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C760 0CE105SK6DC VMV105M050S0ANB010 1uF 20% 50 C822 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V
C761 0CK104CK56A 0603B104K500CT 100nF 10% 50V C823 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V
C766 0CK104CK56A 0603B104K500CT 100nF 10% 50V C828 0CK106DC67A JMK212JB106MG-T 10uF 20% 6.3V
C767 0CK104CK56A 0603B104K500CT 100nF 10% 50V C900 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C768 0CK335FK66A C3225X7R1H335MT 3.3uF 20% 50V C901 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C769 0CK104CK56A 0603B104K500CT 100nF 10% 50V C902 0CE476WH6DC MVK8.0TP25VC47M 47uF 20% 25V
C771 0CH3105H946 C2012Y5V1E105ZT 1uF -20TO+80% C904 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16
C772 0CK104CK56A 0603B104K500CT 100nF 10% 50V C905 0CK226FF67A EMK325BJ226MM-T 22uF 20% 16V
C774 0CK335FK66A C3225X7R1H335MT 3.3uF 20% 50V C907 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C775 0CK104CK56A 0603B104K500CT 100nF 10% 50V C908 0CK103CK56A 0603B103K500CT 10nF 10% 50V X
C909 0CK222CK56A 0603B222K500CT 2.2nF 10% 50V C7 EAD35865801 Harness,Single 150MM 1.25MM 3P
C910 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V IC501 6630B00021A Connector,BtoB KX14-120K5DE 120P
C911 0CK103CK56A 0603B103K500CT 10nF 10% 50V X J100 6630GY00509 Connector,DSUB 9P 2.77MM
C912 0CK103CK56A 0603B103K500CT 10nF 10% 50V X JK100 6630GY00509 Connector,DSUB 9P 2.77MM
C913 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V JK200 6630TGA004F Connector,DSUB 15P 2.29MM
C914 0CHZB00107A 6TPC100M 100uF - 6.3V - - 734 JK201 6630TGA004F Connector,DSUB 15P 2.29MM
C915 0CK224CF56A 0603B224K160CT 220nF 10% 16V JK202 6630TGA005B Connector,DSUB DVI 24P 1.90MM
C916 0CE106WH6DC MVK5.0TP25VC10M 10uF 20% 25V JK700 6630SK00804 Connector,USB UAR24-4K2300 B 1P
C916 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V
P100 6630X60128A Connector,05004HR-20B01S 20P
C917 0CE106WH6DC MVK5.0TP25VC10M 10uF 20% 25V
P101 6602T12005B Connector,Wafer 12505WR-03A00 3P
P102 6602V12001A Connector,Wafer 53261-0290 2P
C918 0CK104CF56A 0603B104K160CT 100nF 10% 16V
P106 6602T12005B Connector,Wafer 12505WR-03A00 3P
C919 0CK104CF56A 0603B104K160CT 100nF 10% 16V
P501 6630B00021A Connector,BtoB KX14-120K5DE 120P
C920 0CK104CF56A 0603B104K160CT 100nF 10% 16V
P651B 6602T12005B Connector,Wafer 12505WR-03A00 3P
P700 6630SK00804 Connector,USB UAR24-4K2300 B 1P
P701 6602T12005D Connector,Wafer 12505WR-05A00 5P
P751 6630B00022A Connector,BtoB KX15-120KLDLE 120P
P800 6630VE00204 Connector,10003HR-04A00 4P
C923 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C924 0CK104CF56A 0603B104K160CT 100nF 10% 16V P801 6602T12005B Connector,Wafer 12505WR-03A00 3P
C925 0CE106WH6DC MVK5.0TP25VC10M 10uF 20% 25V P804 6602T12004B Connector,Wafer 12505WS-03A00 3P
C925 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V P900 6602T12005L Connector,Wafer 12505WR-12A00 12P
C926 0CE106WH6DC MVK5.0TP25VC10M 10uF 20% 25V P901 6602T12004B Connector,Wafer 12505WS-03A00 3P
C926 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V P901 6602V12001A Connector,Wafer 53261-0290 2P
C927 0CE106WH6DC MVK5.0TP25VC10M 10uF 20% 25V P901 6602V12001A Connector,Wafer 53261-0290 2P
C927 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V P902 6602T12004B Connector,Wafer 12505WS-03A00 3P
C928 0CE106WH6DC MVK5.0TP25VC10M 10uF 20% 25V P903 6630X60128A Connector,05004HR-20B01S 20P
C928 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V P903 6602T12004B Connector,Wafer 12505WS-03A00 3P
C929 0CK104CF56A 0603B104K160CT 100nF 10% 16V P904 6602T12004B Connector,Wafer 12505WS-03A00 3P
C930 0CK104CF56A 0603B104K160CT 100nF 10% 16V P905 6602V12001A Connector,Wafer 53261-0290 2P 1.25MM
C931 0CK104CF56A 0603B104K160CT 100nF 10% 16V P906 6602T12004A Connector,Wafer 12505WS-02A00 2P
C932 0CK104CF56A 0603B104K160CT 100nF 10% 16V
C934 0CE106WFKDC MVK4.0TP16VC10M 10uF 20% 16V
INDUCTOR
C935 0CK103CK56A 0603B103K500CT 10nF 10% 50V X
L100 0LC0562001A Inductor,FI-A2012-561KJT 560NH 10% -
C935 0CK103CK56A 0603B103K500CT 10nF 10% 50V X
C936 0CC101CK41A C1608C0G1H101JT 100pF 5% 50V
L300 0LC18000A02 Inductor,FI-B2012-182KJT 1.8UH 10% 1
C940 0CK103CK56A 0603B103K500CT 10nF 10% 50V X
C941 0CK224CF56A 0603B224K160CT 220nF 10% 16V
C942 0CK224CF56A 0603B224K160CT 220nF 10% 16V
C943 0CK224CF56A 0603B224K160CT 220nF 10% 16V
CONNECTOR & WAFER L704 0LC0562001A Inductor,FI-A2012-561KJT 560NH 10% -
C1 6631900021A Harness,Single 100mM 1.25MM 2P L705 0LC0562001A Inductor,FI-A2012-561KJT 560NH 10% -
C2 6631900038A Cable,FFC 250MM 0.50MM 20P L706 0LC0562001A Inductor,FI-A2012-561KJT 560NH 10% -
C3 6631V00043D Harness,Single 250mM 1.25MM 5P L707 EAP32842805 Inductor,NR8040T150M 15UH 20% 0V 2.4
C4 6631V39031D Harness,Single 250mM 3.96MM 3P L751 6140VR0007A Inductor,DT1608C-223 22UH 20% - 500M
C5 EAD35865201 Harness,Single 200MM 1.25MM 2P L752 6140VR0007A Inductor,DT1608C-223 22UH 20% - 500M
C6 EAD35865801 Harness,Single 150MM 1.25MM 3P L903 EAP32842805 Inductor,NR8040T150M 15UH 20% 0V 2.4
R123 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W

JACK
R123 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10
J300 380-336G Jack,RCA PJ6046B-05 8.4MM R124 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
J301 380-363K Jack,DIN PJ6046G SOCKET 4P R125 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
JK300 380-336G Jack,RCA PJ6046B-05 8.4MM R126 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
JK301 380-363K Jack,DIN PJ6046G SOCKET 4P R127 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
RESISTOR
AR200 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R129 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
AR202 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R131 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W
AR203 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R131 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10
AR204 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R132 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
AR300 0RJ0222C692 MNR04 M0APJ 220 22OHM 5% 1/1 R135 0RJ3001D677 MCR03EZPJ302 3KOHM 5% 1/10W
AR301 0RJ0222C692 MNR04 M0APJ 220 22OHM 5% 1/1 R137 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
AR303 0RJ0222C692 MNR04 M0APJ 220 22OHM 5% 1/1 R140 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
R100 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R171 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W
R102 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R200 0RJ0822D677 MCR03EZPJ820 82OHM 5% 1/10W
R104 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W R203 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W
R105 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W R208 0RJ0752D677 MCR03EZPJ750 75OHM 5% 1/10W
R106 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R212 0RJ0752D677 MCR03EZPJ750 75OHM 5% 1/10W
R224 0RJ3001D677 MCR03EZPJ302 3KOHM 5% 1/10W R283 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R233 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R291 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
R236 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W R296 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R239 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W R302 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R240 0RJ2201D677 MCR03EZPJ222 2.2KOHM 5% 1/10 R302 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R243 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R304 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R244 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R304 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R246 0RJ3900D677 MCR03EZPJ391 390OHM 5% 1/10W R305 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R248 0RJ2002D677 MCR03EZPJ203. 20KOHM 5% 1/10 R306 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R250 0RJ2002D677 MCR03EZPJ203. 20KOHM 5% 1/10 R307 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R251 0RJ0332C678 MCR01MZPJ330 33OHM 5% 1/16W R308 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R252 0RJ3900C678 MCR01MZPJ391. 390OHM 5% 1/16 R309 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R253 0RJ0332C678 MCR01MZPJ330 33OHM 5% 1/16W R310 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R254 0RJ0332C678 MCR01MZPJ330 33OHM 5% 1/16W R311 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R255 0RJ0682C678 MCR01MZPJ680 68OHM 5% 1/16W R312 0RJ0752C678 MCR01MZPJ750 75OHM 5% 1/16W
R256 0RJ0682C678 MCR01MZPJ680 68OHM 5% 1/16W R313 0RJ1004D677 MCR03EZPJ105 1MOHM 5% 1/10W
R257 0RJ0682C678 MCR01MZPJ680 68OHM 5% 1/16W R314 0RJ0472D677 MCR03EZPJ470 47OHM 5% 1/10W
R260 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R316 0RJ0472D677 MCR03EZPJ470 47OHM 5% 1/10W
R264 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R317 0RJ0472D677 MCR03EZPJ470 47OHM 5% 1/10W
R267 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W R400 0RJ1002C678 MCR01MZPJ103 10KOHM 5% 1/16W
R268 0RJ2001D677 MCR03EZPJ202 2KOHM 5% 1/10W R401 0RJ0000C678 MCR01MZPJ000 0OHM 5% 1/16W 1
R270 EBC32476501 MCR01MZ5PJ3R3 3.3OHM 5% 1/16 R402 0RJ0000C678 MCR01MZPJ000 0OHM 5% 1/16W 1
R271 EBC32476501 MCR01MZ5PJ3R3 3.3OHM 5% 1/16 R403 0RJ1002C678 MCR01MZPJ103 10KOHM 5% 1/16W
R272 0RJ2001D677 MCR03EZPJ202 2KOHM 5% 1/10W R404 0RJ1002C678 MCR01MZPJ103 10KOHM 5% 1/16W
R273 EBC32476501 MCR01MZ5PJ3R3 3.3OHM 5% 1/16 R405 0RJ1002C678 MCR01MZPJ103 10KOHM 5% 1/16W
R274 EBC32476501 MCR01MZ5PJ3R3 3.3OHM 5% 1/16 R407 0RJ0332C478 MCR01MZPF330 33OHM 1% 1/16W
R277 EBC32476501 MCR01MZ5PJ3R3 3.3OHM 5% 1/16 R500 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R278 EBC32476501 MCR01MZ5PJ3R3 3.3OHM 5% 1/16 R505 0RJ0222C678 MCR01MZPJ220 22OHM 5% 1/16W
R279 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W R506 0RJ0222C678 MCR01MZPJ220 22OHM 5% 1/16W
R601 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R653 0RJ3301C678 MCR01MZPJ332 3.3KOHM 5% 1/16
R602 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W R654 0RJ3301C678 MCR01MZPJ332 3.3KOHM 5% 1/16
R607 0RJ0222D477 MCR03EZPF220 22OHM 1% 1/10W R708 0RJ0272D677 MCR03EZPJ270 27OHM 5% 1/10W
R609 0RJ0222D477 MCR03EZPF220 22OHM 1% 1/10W R710 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W
R610 0RJ0222D477 MCR03EZPF220 22OHM 1% 1/10W R711 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R612 0RJ1001C678 MCR01MZPJ102 1KOHM 5% 1/16W R712 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
R613 0RJ1001C678 MCR01MZPJ102 1KOHM 5% 1/16W R713 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
R619 0RJ0392D477 MCR03EZPF390 39OHM 1% 1/10W R721 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10
R623 0RJ0392D477 MCR03EZPF390 39OHM 1% 1/10W R727 0RJ2002D677 MCR03EZPJ203. 20KOHM 5% 1/10
R629 0RJ0342D477 MCR03EZPF34R0 34OHM 1% 1/10W R734 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R632 0RJ1180D477 MCR03EZPF1180 118OHM 1% 1/10 R737 0RJ1001D477 MCR03EZPF102 1KOHM 1% 1/10W
R633 0RJ0392D477 MCR03EZPF390 39OHM 1% 1/10W R738 0RJ2492D477 MCR03EZPF2492 24.9KOHM 1% 1/
R753 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R829 0RJ5601D677 MCR03EZPJ562 5.6KOHM 5% 1/10
R753 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W R830 0RJ1000D477 MCR03EZPF101 100OHM 1% 1/10W
R754 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R831 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R755 0RJ4301D477 MCR03EZPF432 4.3KOHM 1% 1/10 R832 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R756 0RJ1802D477 MCR03EZPF183 18KOHM 1% 1/10W R900 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10
R757 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R900 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10
R759 0RJ4991D477 MCR03EZPF4991 4.99KOHM 1% 1/ R901 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W
R759 0RJ4991D477 MCR03EZPF4991 4.99KOHM 1% 1/ R901 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W
R764 0RJ1003D677 MCR03EZPJ104 100KOHM 5% 1/10
R765 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R903 0RJ2201D477 MCR03EZPF222 2.2KOHM 1% 1/10
R772 0RJ2002D677 MCR03EZPJ203. 20KOHM 5% 1/10
R772 0RJ2002D677 MCR03EZPJ203. 20KOHM 5% 1/10
R906 0RJ4991D477 MCR03EZPF4991 4.99KOHM 1% 1/
R773 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
R909 0RJ1802D477 MCR03EZPF183 18KOHM 1% 1/10W
R910 0RJ1052D477 MCR03EZPF1052 10.5KOHM 1% 1/
R778 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R911 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W
R781 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10 R911 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W
R784 0RJ1003D677 MCR03EZPJ104 100KOHM 5% 1/10 R912 0RJ0222D677 MCR03EZPJ220 22OHM 5% 1/10W
R800 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W R919 0RJ2201D477 MCR03EZPF222 2.2KOHM 1% 1/10
R801 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W R920 0RJ3301D477 MCR03EZPF332 3.3KOHM 1% 1/10
R802 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W R921 0RJ6801D477 MCR03EZPF682 6.8KOHM 1% 1/10
R803 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R921 0RJ8201D477 MCR03EZPF8201 8.2KOHM 1% 1/1
R823 0RJ1800D677 MCR03EZPJ181 180OHM 5% 1/10W R934 0RJ2702D477 MCR03EZPF273 27KOHM 1% 1/10W
R824 0RJ3301D677 MCR03EZPJ332 3.3KOHM 5% 1/10 R936 0RJ2702D477 MCR03EZPF273 27KOHM 1% 1/10W
L804 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1

SWITCH
SW1 6600X000017 Switch,Micro KMM-1283NPL 1C2P L900 6200J000123 Filter,LCR NFE31PT222Z1E9L LPF(E
SW901 6600VR1004A Switch,Tact SKHMPWE010 1C1P 1 L901 6200J000123 Filter,LCR NFE31PT222Z1E9L LPF(E
SW902 6600VR1004A Switch,Tact SKHMPWE010 1C1P 1 L902 6210TCE001G Filter,Bead HH-1M3216-501JT 500OH
SW903 6600VR1004A Switch,Tact SKHMPWE010 1C1P 1 L904 EAM32500502 Filter,Bead BLM18AG151SN1D 150ohm
SW907 6600VR1004A Switch,Tact SKHMPWE010 1C1P 1 X200 6202VDT002B Crystal,SX-1 14.31818MHZ
SW908 6600VR1004A Switch,Tact SKHMPWE010 1C1P 1 X300 6212AB2883A Crystal,HC-49SM 27.00000MHZ
SW909 6600VR1004A Switch,Tact SKHMPWE010 1C1P 1
MISCELLANEOUS
FILTER & CRYSTAL
IC100 6712000002B Receiver Module,KSM-603SM12E-1
F1 5230V00030C Filter,CUTTING ACRYL GLASS F IC401 SAA30850506 S/W,Firmware 3.00 F6C0
F2 6200JB8012Y Filter,Ferrite Core ZCAT1730-0730A-M-K IC802 6712000002B Receiver Module,KSM-603SM12E-1
L103 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 L1 3680V00131A Lens,C-LENS ASSEMBLY RD-JT91
L200 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 L2 3680V00158A Lens,LENS RD-JT90 XGA 0.7INCH
L201 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 L3 MFB39220201 Lens,DX535-JD Step Light Tunnel (5.5°ø4.5°ø30mm)
L202 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 M1 5018V00093A Mirror,DLP PROJECTOR
L203 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 M1 5018V00094A Mirror,FRONTSIDE 39*25 RD-JT90
L204 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 NR03 6322A00028A Thermistor,NTC NCP18WB473F10RB 47KOHM 1%
L205 6210TCE001A Filter,Bead HB-1S2012-080JT 8OHM NR03 6322A00028A Thermistor,NTC NCP18WB473F10RB 47KOHM 1%
L206 6210TCE001A Filter,Bead HB-1S2012-080JT 8OHM S1 4970V00067C Socket,IC PLATE 8614-001, C-SPRING
L207 6210TCE001A Filter,Bead HB-1S2012-080JT 8OHM X600 6204B48342A Oscillator,Crystal ASV-50.000MHZ-R-T
ACCESSORIES
L211 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 A1 SAC30666004 Title,DX535-JD CD MANUAL
L301 6210TCE001S Filter,Bead HU-1M2012-121 120OHM A1 MFL38958001 Manual,Owners SIMPLE BOOK EN(1)
L302 6210TCE001S Filter,Bead HU-1M2012-121 120OHM A2 6710V00133V Remote Controller,DX535 DATA LASER
L400 6210TCE001S Filter,Bead HU-1M2012-121 120OHM A3 EAD37992101 Power Cord
L500 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 A3 6410TAW001A Power Cord *LGESA
L501 0LCML00003B Filter,Bead MLB-201209-0120P-N2 1 A4 6852TAZ006Z Cable,Assembly RCA PLUG
L600 6210TCE001S Filter,Bead HU-1M2012-121 120OHM A5 6866VA9001A Cable,Assembly D-SUB CONNECTOR(M)
L601 6210TCE001S Filter,Bead HU-1M2012-121 120OHM A6 MCK32380702 Cover,MOLD PP DX535-JD PP LANS CAP BLACK
L602 6210TCE001S Filter,Bead HU-1M2012-121 120OHM A7 4930V00083B Holder,LENS STRING RL-JT10
L603 6210TCE001S Filter,Bead HU-1M2012-121 120OHM
L708 6210TCE001G Filter,Bead HH-1M3216-501JT 500OH
L709 6210TCE001G Filter,Bead HH-1M3216-501JT 500OH
L710 6200J00005F Filter,Bead HB-1M1608-102JT 1000O
Copyright © 2007 LG Electronics. Inc. All right reserved. LGE Internal Use Only
MAIN(TOP) IR(TOP) IR(BOTTOM)
MAIN(BOTTOM) Temp(TOP) C/W(TOP)
C/W(BOTTOM)
Temp(BOTTOM)
CONTROL(TOP) DMD(TOP)
DMD(BOTTOM)
CONTROL(BOTTOM)
Aug., 2007
P/NO : 3828VD0236N Printed in Korea

LG Dx325 DLP Projector

Uploaded by

Copyright:

Available Formats

LG Dx325 DLP Projector

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG Dx325 DLP Projector

Uploaded by

Copyright:

Available Formats

Internal Use Only

MODEL : DX535 DX535-JD

SAFETY PRECAUTIONS .................................................................................3

REPLACING OF LAMP ....................................................................................4

EXPLODED VIEW PARTS LIST .....................................................................17

REPLACEMENT PARTS LIST........................................................................18

SVC. SHEET .......................................................................................................

PRINTED CIRCUIT BOARD ...............................................................................

IMPORTANT SAFETY NOTICE

General Guidance Leakage Current Hot Check (See below Figure)

Good Earth Ground

* The projected image gets darker or starts to deteriorate. Lamp indicators

Be careful when replacing lamp

To obtain a replacement Lamp unit

Lamp unit disposal

Dispose of the used lamp by returning it to the LG Electronics Service Center.

1 Turn off the projector and unplug the power cable.

(Allow the lamp to cool for 1 hour before

Lamp case screw

After lifting the lamp cover off, remove the two

3 retaining screws on the lamp case with a screw-

5 Pull out the handle slowly and remove the lamp

Close the lamp cover and install the screws from

A Test and Inspection Method

1 Video input applicable system 1) NTSC M 3.579545 / 60Hz

1 REMOCON NEC Code LGE key

(1) Select ‘Video mode’ as input source.

(3) Left and Right Adjustment 2

Left and right

Left and right

4-1. Illuminator Adjustment Sequence (4) Final Adjustment

(1) Up and Down Adjustment

Illuminator goes down direction Illuminator goes down area

Adjustment Screw Screen state

Right At first, upside illuminator goes down

Left At first, downside illuminator goes

4-3. Coherent Light Source Adjustment

<Fig. 5> Coherent Light Source

6. EDID Data input

DLP PJTR SET

JIG <Fig. 8> White/Black Pattern

Colow wheel index

(2) Select ADJ -> 3. Component Gain/Offset -> A (Enter) -> G

<Fig. 11> Full RED Pattern

Set fixing device

<Fig. 10> Device Setting Diagram for CWI Adjustment

12-2. Equipment Composition 13-2. Configuring the Projector Brightness

(1) Select Model

Set fixing device

<Fig. 12> Device Setting Diagram

<Fig. 14> Configuring the Brightness Measuring JIG

Only for training and service purposes

Copyright © 2007 LG Electronics. Inc. All right reserved.

LGE Internal Use Only

104 4810V01056N Bracket,COMPLEX FAN DX535-JD FM73A EGI DMD

107 4811V00348E Bracket Assembly,FAN DX535-JD FM73A POWER

300 ABQ32155702 Case Assembly,FM73A DX535-JD.AEULLAX TOP

301 AGU32157002 Plate Assembly,DECO DX535 LENS

400 ABQ32150001 Case Assembly,FM71A AH115P-JD.ABGLLAX BASIC