SG-002 Signal Generator English Manual

0-10V/0-22m AVoltage and current source
signal generator Manual

1.Technical Index
1.1 External power supply DC15-30V power 1w (not charging)/5W (charging);
1.2 3.7V lithium battery capacity 1100mAh, maximum charging current 0.8A
(optional);
1.3 External microUSB-5V current 0.2A (not charging)/1A (charging);
1.4 The voltage output is adjustable from O-10V, the accuracy after calibration
is 0.01V, and the maximum current is 20mA;
1.5 The current output is adjustable from O-22mA, the accuracy after
calibration is 0.01mA,The current sampling resistance is not more than 500
ohms;
1.6 The digital tube displays 4 digits, two decimal places;
1.7 Encoder knob 1 circle: 30 pulses;
2.Power Supply
3 power supply methods, as long as one is used, it can work, and it can be
connected at the same time;

3. Dimensions
4. Wiring Diagram
How to judge whether it is active or passive connection? Common methods are
as follows:
1 ：See the internal schematic document of the device， I+ is 24V+，it is the
passive connection； I- is 24VG，it is the active connection；
2 ：Use a multimeter to measure the voltage between I+ and I-， =0V is the
active connection， =24V is the active connection；

5. Voltage/Current switching
Press the MODE button, one key switch to adjust the voltage and current
mode；The indicator shows what state it is in，System operation corresponds to
which mode to operate；The original mode after switching,Will continue to
output，It’s just not in a state of adjustment；
6. System Operation ( Where "OK<confirm key>" is：Push

the knob down，Turn clockwise to ”+< ADD >” ，，
Anticlockwise rotation ” –< reduce> ”) ：
6.1 In the normal operation screen, short press the confirm key to save the
output value ，After letting go，Screen display"...",Successfully saved,After the
next boot,The output value is this saved value；When debugging equipment，
We need to randomly adjust the output value，Just don’t press the encoder
knob，After restarting, the original value will be saved；
6.2 Parameter settings：
6.2.1 In the normal operation screen,Press and hold the confirm button for 2
seconds,Enter setting state ，Display”F001”(Parameter number 001);
6.2.2 Turn the knob to change the parameter number (First entry F002 Need to
enter the password first“+ - - + （Rotate the knob）”)；
6.2.3 Parameter number interface，Press the confirm key to enter the
corresponding parameter value setting，Rotate the knob to modify the
parameters；
6.2.4 Press the confirm key to save the parameters，Exit the parameter setting，
Display the next parameter number（No password is entered, after setting F001
value, it will enter the normal operation screen）；
6.2.5 Rotate the knob directly to the last parameter number, press the OK key,
the setting is completed and enter the normal operation screen;
6.2.6 If there is no operation on the parameter setting screen for more than
10s, it will exit the setting state and enter the normal operation screen;
6.3 For example:
6.3.1 Modify "F001" coarse and fine adjustment
mode
Figure 1→2: Press and hold the knob for 2 seconds，Enter setting state，Display
“F001”;
Figure 2→3: Press "OK"，Set the value of "F001"设，Turn the knob to modify it；
Figure 3→4: Press "OK"，Exit the setting state after saving，Enter the normal
adjustment state；6.3.2 Modify "F006" calibration value（It’s best to adjust the
output to 10V or 20mA first, and Recalibrate ）
Figure 1→2: Press and hold the knob for 2 seconds，Enter setting state，
Display“F001”;
Figure 2→3: “+”1 Pulse，Display“- - - -”；
Figure 3→4: Enter password“+ - - +”，Display“= = = =”；
Figure 4→5: Press "OK", if the password is entered correctly, it will display
"F002", otherwise it will display "Err" to exit, there may be an error, please
enter it again;
Figure 5→6: Rotate the knob "+" to display to“F006”；
Figure 6→7: Press "OK",Enter to set the parameter value of "F006",Then modify
this value,Make the actual output equal to the display value before entering the
setting state;
Figure 7→ : Press "OK" to save, or automatically exit the setting state after 10s
of inactivity, and the parameters will not be saved;
6.4 In the voltage regulation mode, enter the voltage setting, parameter
description table：
6.5 Enter F002, you need to enter the password first“+ - - +(Turn the knob to
display----)”
NO. Description Introduction Default
F001 Rough 0: Rough adjustment 1: Fine-tuning 0
adjustment OR
Fine-tuning
F002 Output mode 0:0-10V 1:2-10V 2:0-5V 3:1-5V 4:0-3.3V 0
F003 Display mode 0:Actual voltage 1:Percentage0-100.0 2:50HZ 0
F004 Coarse 1-50 Plus and minus numbers for each pulse ， No 1
adjustment decimal point concept (1-50)×10
mode plus and
minus value
/Per pulse
F005 Fine-tuning 1-50 Plus and minus numbers for each pulse ， No 1
mode addition decimal point concept (1-50)
and subtraction
/Per pulse
F006 Output -999 -- +999 For internal reference only, please be
calibration cautious when modifying
value
F007 Digital tube 1-8 ：Level 1 is the darkest, level 8 is the brightest 1
brightness
6.6 In the regulation current mode, Enter the current setting,
6.7Parameter description table:you need to enter the password first“+ - -
+(Turn the knob to display----)”

NO. Description Introduction Default
F001 Rough 0: Rough adjustment 1: Fine-tuning 0
adjustment OR
Fine-tuning
F002 Output mode 0:0-20mA 1:4-20mA 2:0-22mA 0
F003 Display mode 0:Actual current 1:Percentage0-100.0 2:50HZ 0
F004 Coarse 1-50 Plus and minus numbers for each pulse ， No 1
adjustment decimal point concept (1-50)×10
mode plus and
minus value/Per
pulse
F005 Fine-tuning 1-50 Plus and minus numbers for each pulse ， No 1
mode addition decimal point concept (1-50)
and subtraction
/Per pulse
F006 Output -999 -- +999 ，For internal reference only，Please be
calibration cautious about modification, about 20mA±4mA
value
F007 Digital tube 1-8 ： Level 1 is the darkest, level 8 is the brightest 1
brightness
7 Current output test method: AIo GND
We often encounter people who say that there is no current when measuring
current. In fact, the ammeter is broken, the gear is wrong or the wrong hole is
inserted. There is a fuse inside the multimeter to measure the current. This is
easy to blow, so we use the method of voltage measurement. Verify the
transition of the signal generator as follows:
7.1 The simplest method: power on, directly measure the voltage between
AIo and GND when there is no load, =0V is a defective, otherwise 99% may be
no problem, because when there is voltage to measure current, it is equivalent

to short circuit and there will definitely be current ；
7.2 Connect an LED indicator, if the brightness changes with the adjustment,
then the signal generator current output is no problem;
7.3 Connect a 50-300 ohm resistor to AIo GND. If there is voltage and it meets
"Voltage = Current X Resistance", the voltage will change with the adjustment,
then the signal generator current output is no problem;
7.4 If there is a PLC/inverter, measure the resistance between I+ and I-. If it is
between 50-300 ohms, you can use it as a test resistance. Connect AIo to I+,
GND to I-, and measure the voltage. If there is voltage, and Satisfy "Voltage =
Current X Resistance", the voltage will change with the adjustment, then the
signal generator current output is no problem;

8 NOTE：
8.1 Please read this manual carefully before use；
8.2 Turn off the power before wiring
8.3 Exceeding the range shown in the technical indicators may cause the
instrument to work abnormally or even be damaged；

SG-002 Signal Generator English Manual

Uploaded by

Copyright:

Available Formats

SG-002 Signal Generator English Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SG-002 Signal Generator English Manual

Uploaded by

Copyright:

Available Formats

0-10V/0-22m AVoltage and current source

signal generator Manual

1.1 External power supply DC15-30V power 1w (not charging)/5W (charging);

1.3 External microUSB-5V current 0.2A (not charging)/1A (charging);

is 0.01V, and the maximum current is 20mA;

calibration is 0.01mA,The current sampling resistance is not more than 500

1.6 The digital tube displays 4 digits, two decimal places;

1.7 Encoder knob 1 circle: 30 pulses;

connected at the same time;

1 ：See the internal schematic document of the device， I+ is 24V+，it is the

passive connection； I- is 24VG，it is the active connection；

active connection， =24V is the active connection；

mode；The indicator shows what state it is in，System operation corresponds to

which mode to operate；The original mode after switching,Will continue to

output，It’s just not in a state of adjustment；

6. System Operation ( Where "OK<confirm key>" is：Push

output value ，After letting go，Screen display"...",Successfully saved,After the

next boot,The output value is this saved value；When debugging equipment，

knob，After restarting, the original value will be saved；

6.2 Parameter settings：

enter the password first“+ - - + （Rotate the knob）”)；

6.2.3 Parameter number interface，Press the confirm key to enter the

corresponding parameter value setting，Rotate the knob to modify the

value, it will enter the normal operation screen）；

the setting is completed and enter the normal operation screen;

6.3 For example:

6.3.1 Modify "F001" coarse and fine adjustment

adjustment state；6.3.2 Modify "F006" calibration value（It’s best to adjust the

output to 10V or 20mA first, and Recalibrate ）

Figure 2→3: “+”1 Pulse，Display“- - - -”；

Figure 3→4: Enter password“+ - - +”，Display“= = = =”；

Figure 5→6: Rotate the knob "+" to display to“F006”；

of inactivity, and the parameters will not be saved;

6.7Parameter description table:you need to enter the password first“+ - -

+(Turn the knob to display----)”

7 Current output test method: AIo GND

easy to blow, so we use the method of voltage measurement. Verify the

transition of the signal generator as follows:

no problem, because when there is voltage to measure current, it is equivalent

then the signal generator current output is no problem;

then the signal generator current output is no problem;

7.4 If there is a PLC/inverter, measure the resistance between I+ and I-. If it is

signal generator current output is no problem;

8.2 Turn off the power before wiring

instrument to work abnormally or even be damaged；

You might also like