EPCOS Thyristor Duty Switching

Switching Devices - Thyristor Modules
for Dynamic PFC TSM Series

Ultrafast Smooth Switching  Natural Cooled  Compact Design  Enhanced Life of System
General The solution for this are dynamic

Conventional systems for power power factor correction systems.
factor correction are used to With the thyristor module series
optimize the power factor and TSM-LC and TSM-HV, we provide
reduce the level of harmonics in the main component – “the electronic
the grid. The usage of new switch” – for dynamic power
technologies in modern industry factor correction.
has negative impacts on electric The TSM module series offers fast
power quality of the main supply electronically controlled, self-
networks, e.g. frequent high load observing thyristor switches for
fluctuations and harmonic capacitive loads up to 50 KVAr, that
oscillation. are capable to switch PFC capacitors
within a few milliseconds nearly
Excessive currents, increased without a limitation to the number
losses and flickering will not only of switchings during the capacitor
influence the supply capacity but lifetime.
will also have a significant impact
on the operation of sensitive
electronic devices.
Applications Features
Main supply networks with high Easy installation: it can be used
load fluctuations for dynamic similar to a contactor
PFC systems All the intelligence needed is
Presses offered within the thyristor module
Welding machines itself
Elevators Reaction time: 5 milliseconds only
Cranes Permanent self-controlling of:
Wind turbines – voltage parameter
– phase sequence
– capacitor output
Display of
– operation
– faults
– activation
Voltage range: 440 V and 690 V
Output range:
440 V: 10, 25 and 50 KVAr
690 V: 50 KVAr
51
Dynamic PFC network BR5000-T multiple stages
Dynamic PFC network BR6000-T multiple stages
52
Selection table TSM series

TSM-LC 10 TSM-LCN 25 TSM-LCN 50 TSM-HV 50
Ordering code B44066T0010R440 B44066T3025R442 B44066T3050R442 B44066T0050R690

Rated voltage 380 … 440 V 380 … 440 V 380 … 440 V 690 V
Max. grid voltage: 440 V 440 V 440 V 690 V
– in conventional PFC
systems(without reactors)
– in detuned PFC system 440 V 440 V 440 V 690 V
(7% detuning) (no upwards tolerance) (no upwards tolerance) (no upwards tolerance)
– in detuned PFC 400 V 400 V 400 V 690 V
system (14% detuning)
Frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz
Maximum power / 10 KVAr 25 KVAr 50 KVAr 50 KVAr
at nominal voltage
Power circuit Direct connection Direct connection Direct connection Direct connection
4 pole via terminal (cable lug 35mm2) (cable lug 35mm2) 4 pole via busbar
clamps (D = 6 mm2 (cable lug 25mm2
resp. 4 mm2) D =8 mm)
Neutral required No* No* No* Yes**
Aux. supply voltage No No No 230 V AC
required
Connection from bottom from bottom from bottom from bottom
Losses (PD in W) 2.0 x l (in A) typical; 2.0 x l (in A) typical; 2.0 x l (in A) typical; 3.0 x l (in A) typical; at
35 W (thermal) 75 W (thermal) 150 W (thermal) 690 V/ 50 KVAr approx.
125 W (thermal)
Recommended fuses 3 x BS Type 3 x BS Type 3 x BS Type 3 x BS Type
“superfast” (AC 690 V) 40 A (AC 690 V) 80 A (AC 690 V) 160 A (AC 690 V)
Dimensions in mm 163 x 150 x 75 157 x 200 x 180 157 x 200 x 180 157 x 200 x 195
(w x h x d )
Weight 1.75 kg 4.8 kg 4.8 kg 5 kg
LED display per phase 2 2 2 1
Cascading yes yes yes yes
Ambient temperature –10 °C ... 55 °C –10 °C ... 55 °C –10 °C ... 55 °C –10 °C ... 55 °C
Discharge resistors 1 1 1 Standard resistor
EW-22 needed sufficient
Three phase current 1 1 1 1
limitation reactor needed***
*For operation with three-phase capacitor or three single-phase capacitors. **Only for and compulsorily for operation with single-phase capacitors. ***For PFC systems without detuning reactors mandatory.
Accessories for TSM-LC modules

Type/Description Ordering Code
Discharge resistors EW-22 at least 1 piece per step B44066T0022S400
to be used for all types of TSM-LC if fast re-switching time
is required. For higher rated steps please contact your
local sales office.
EW-22:
Dimensions (w x d x h) : 90 x 50 x 100 mm
Weight (approx.) : 0.3 kg
Design panel : for mounting on heat sink/fitting
Connection : wago terminal, ready for three-phase
connection to the capacitor
Note :
Three phase current limitation reactor for thyristor modules
TSM-series in conventional dynamic PFC-systems without reactor is a must
Used for limitation of the pace of current increase di/dT in the thyristors
to the maximum permissible value
53

EPCOS Thyristor Duty Switching

Uploaded by

Copyright:

Available Formats

EPCOS Thyristor Duty Switching

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EPCOS Thyristor Duty Switching

Uploaded by

Copyright:

Available Formats

Switching Devices - Thyristor Modules

for Dynamic PFC TSM Series

General The solution for this are dynamic

Dynamic PFC network BR5000-T multiple stages

Dynamic PFC network BR6000-T multiple stages

Selection table TSM series

Ordering code B44066T0010R440 B44066T3025R442 B44066T3050R442 B44066T0050R690

Accessories for TSM-LC modules

You might also like