B59002

User Manual

Please refer to this manual before using the product.

Cautions before using
1. The company reserves the right to modify the contents of this manual without any further
notification. It is normal that some functions may vary in certain versions of software.

2. Please charge this product with the charger provided for no less than 2 hours before using it
for the first time.

3. In the APP, set personal information to sync time before using the smart watch. Please refer to
the instructions about synchronization for details.

4. The watch has IP68 waterproof rating. It cannot be used in corrosive liquids or hot water, tea,
etc. It is not compatible with deep sea diving of more than 3 meters. All the above situations will
cause damage to the smart watch (these damages will not be covered by the warranty).

1. Product overview

Models can be paired with:

• Android phone: supports OS 5.0 and above

• Iphone : supports OS 9.0 and above

2. APP download and connection

2.1 Please scan the QR code below to download APP

It is recommended to use a browser to scan and download the app. Please give the
corresponding permissions in the download and installation process to ensure a good
Bluetooth connection.
The APP name is “LinkTo Sport”.
 QR code to download LinkTo Sport LinkTo Sport app icon

Notes:

1. For Apple phone users: If it is in standby or hibernation state for a long time (for example, for 2
hours or more, the phone has not been used and it is in a black screen state), LinkTo Sport will be
cleaned up by the iOS system, so the APP and the watch will disconnect and the functions on the
APP will not be available. Please re-open it and they will automatically reconnect.

2. For Android phone users: After installing the APP on the phone, you need to enable the
background application launch permission in the settings of your phone. Each smart phone is
different. Take a Huawei phone as an example. The steps are as follows:

Settings--Application--Application Launch Management—LinkTo Sport, find the application,

change the automatic management to manual management, open all permissions (allow
Auto-launch, Secondary launch, Run in background). This is only for the application to maintain
the Bluetooth connection with the watch while the phone is in standby mode (the phone does
not have a bright screen). This permission will not use network traffic, nor does it affect the
power consumption of the phone.

2.2 Link APP and smart watch

2.2.1 Open the application, choose "Register" or "Login without registering".

2.2.2 For Android users: click on “Pair new device” and select the model that
corresponds with your smart watch. Then the QR code scanner will open.

2.2.3 Open the QR code on the watch and scan to link the watch. It will take about
30 seconds to connect properly after scanning. Confirm all permission requests
that appear automatically to ensure that all functions work correctly.

2.2.4 For iPhone users: The request to "pair new device" will appear on your
phone after scanning.
 2.2.5 If the QR code scan fails, select the manual connection function to complete
the pairing via Bluetooth.

2.3 APP settings (functions are available only if watch and phone have been paired
succesfully)

• Call notification: Tap to turn on/off this function. If turned on, you can hang up
the incoming call on your watch.
• Social media notifications: Tap to turn on/off and choose which apps’
notifications you want to receive on your watch.
• Alarm clock (up to 5 alarms)
• Sedentary reminder: Tap to turn on/off. Set starting time, end time, interval
and threshold.
• Drink water reminder: Tap to turn on/off. Set starting time, end time, interval
and threshold.
• DND mode (Do not disturb mode): Tap to turn on/off. Set starting time and
end time. Note: when turned on, the watch will not receive notifications.
• Turn on screen when turning wrist: Tap to turn on/off.
• Heart rate monitoring: Tap to turn on/off. Set starting time, end time, and
interval. If turned on, the watch will automatically monitor heart rate, and sync
data to APP.
• Remote camera control (on some phones it may be necessary to turn on the
camera manually on the phone)
• Find device: Upon tap, watch will pop up a watch icon and vibrate.
• Firmware update (make sure there is at least 50% battery before updating,
keep your watch near your phone during the update)
• Device version: To check firmware version of the watch.
• Unbound (iPhone users must enter phone settings, enter Bluetooth settings
and ignore the device to make sure the device is completely disconnected)

3. Main functions

3.1 Basic Operation

3.1.1 Power on: Long press the button for 3 seconds to turn on the watch, short press
the button to light up the watch if it is in standby mode.

3.1.2 Power off: if the screen is on, long press the button for 3 seconds to turn the
watch off.

3.1.3 Watch interface shift process:

 1. Slide from top to bottom on the main screen dial to see the status bar, which
includes DND mode, brightness level, settings, connection icon, and battery.

2. Slide from right to left on the main screen to enter the menu.

3. Slide from left to right on the main screen to see the health and sleep data.

4. Slide from bottom to top on the main screen to see the messages received.

3.2 Main screen selection

Long press the screen for 3 seconds to display all the options to choose from, slide left and
right to choose the preferred main screen. Single touch to set it as default main screen.

3.3 Pedometer

The watch automatically records steps, distance and calories whenever the watch is on. To
see the data from the pedometer: swipe right from the watch's main screen or swipe left
from the main screen to access the menu.

3.4 Sport mode

3.4.1 Sport mode includes outdoor walking, indoor walking, outdoor running, indoor
running, cycling, hiking and swimming. This smart watch is not equipped with GPS,
therefore the results of some sport modes that require A-GPS support may vary with
different phones.

3.4.2 Click the icon to enter the corresponding sport mode and customize the goal of
the day (distance, time or calories) or set no goals. The smart watch will automatically
save the setting, and will apply it the next time that sport mode is used.

3.4.3 Historical data: it saves the last 8 records. The records will be displayed in
chronological order and can be viewed by sliding up and down.

Note: The data will only be saved when the exercise time is more than 5 minutes or
 more than 200 steps. Either one of those conditions will activate the recording function,
otherwise the recording function will fail due to insufficient data.

3.4.4 When you start recording the data, the watch screen will display the following
content: type of sport and start time. You can swipe up and down to see detailed
records. The data will vary according to the type of sport.

3.4.5 Goal completion: The smart watch will display ‘Goal completed’ when the preset
goal is accomplished. Moreover, the record function will keep recording if the exercise
continues.

3.5 Sleep Monitor

The default sleep monitor starts at 21:00 pm and ends at 7:30 am the next day. If the watch
is worn while sleeping, you can check the sleep time on the watch in the following morning.
If the smart watch is paired with the phone, the sleep data will be synchronized
automatically (or manually) with the application.

Note: The smart watch is able to automatically identify the sleeping status. There may be
differences between the detected data and the actual data because the watch may still be
under the detection process. The watch will display the detected result of the whole night,
which will be identical with the actual sleep data, once it finishes the monitoring. There may
be some deviation with the actual sleeping status due to the change in different sleep
modes.

3.6 Health

3.6.1 Heart rate: The display will show "--Bpm". Two seconds later the heart rate test
begins. The data will be displayed on the watch screen when the heart rate data is
detected and the detection will be carried out continuously. If you want to stop the
detection, swipe right to exit and return to the previous screen. In the app, you can
check the historical data, including the highest and average data from the last test.

3.6.2 Blood pressure: The display will show "--mmHg". Two seconds later the blood
pressure test begins. The data will be displayed on the watch screen when the blood
pressure data is detected and the detection will be performed continuously. If you want
to stop the detection, swipe right to exit and return to the previous screen.

Note: All heart rate and blood pressure test will take about 10-30 seconds to generate
data.

3.7 Notifications (messages)

After you have successfully paired your phone and activated the notifications in the app, the
messages received on the phone will be synchronized with the watch. The watch saves the
last 8 messages and they can be deleted by sliding up and clicking on the trash can icon.

Note: the received messages can be read on the smart watch, but they cannot be answered
from the watch and audios cannot be played.

3.8 Alarm clock (only set via APP)

The application supports setting a maximum of 5 alarms.

3.9 Remote music player

3.9.1 If the watch has not been paired with your phone, an ‘unconnected’ message will
pop up when you click the ‘Music’ icon, and it will automatically exit without any
actions after 2 seconds.

3.9.2 After pairing the watch with your phone, you can enter the music player function
of the watch to control the phone’s music player. There may be some compatibility
problems due to the variety of music players. Usually the watch can control your
phone’s music player directly, but some player may need to be opened manually before
been remotely controlled by the watch.

3.9.3 The watch can pause, play and switch to the previous or next song, but it does not
show the name of the song and cannot adjust the volume.

3.10 Pairing with QR code

In the application, select “Pair new device” to scan the QR code of the watch and thus link
with the phone. The "connection" icon in the watch's drop-down menu will appear blue if
the watch is connected. Each watch can only be connected with one phone.

3.11 Timer

Set target time, then click start icon. The message “timed out” will pop up on the screen and
the watch will vibrate.

3.12 Stop watch

Click start icon to start counting. Click the Pause icon to stop, click the clock icon to set a lap
time. If the counting is stopped, the clock icon will change to two arrows, if it is clicked, the
counting will stop and all records will be cleared. The watch keeps records of up to 20 lap
times.

3.13 Find phone

 If the watch is paired with the phone, when you click "Find phone" on the watch, the phone
will vibrate and ring.

3.14 Settings

Screen brightness setting: there are 5 levels of brightness, click the screen to adjust it.

QR code to download the app: you can use your phone to scan this QR code in order to
download the latest version of the app.

Remote camera control: if the watch is paired with the phone, when you click on the
camera function on the watch, a camera icon will appear on the watch and the phone's
camera will open. If you click on the camera icon on the watch, it will take a photo on
the phone and be automatically saved in the phone's photo album. On some phones, it
will be necessary to open the camera manually before using this function.

Reset: tap the left icon to exit, and tap right icon to reset. Then all data of the watch
would be cleared. Note: the data of the paired phone will not be cleared unless the
phone is also reset.

About: you can see the Mac address of the device, the bluetooth name, and the
firmware version.

4. Precautions

4.1 Only one smart watch pairing application should be installed on the phone to ensure that the
connection with the smart watch is normal. If several applications are connected, they can affect
the connection between the watch and the phone.

Note: Some Android phones will prompt you that you cannot install them. Please go to ‘settings’
of the phone and authorize the ‘Unknown source’.

4.2 When the mobile phone requests permissions, click "Allow". On the contrary, you may not
receive notifications, scan QR codes, open the remote camera or use other functions. These
permissions do not affect the flow of the phone or other information on the phone.

4.3 Some Android phones may accidentally close the app when cleaning the applications. Please
keep the app running in the background.

Android phone settings (background running method): open the phone settings - application
management – LinkTo Sport - Rights management - Backstage management - select background
running. (The setting method may be different due to different mobile phone versions and
models).

4.4 Heart rate monitoring requires that the watch and arm are in contact, and the watch should
not be too tight or too loose. The test may be inaccurate if it is too tight because it will affect
blood flow, and if it is too loose because it will affect heart rate sensor monitoring.

4.5 Avoid hitting the smart watch, it could break the glass.

4.6 Use 5V, 1A for charging. This product does not support fast charging. Do not charge if the
watch has water (or sweat) to avoid short circuits and damaging the product.

4.7 This product is an electronic monitoring product, not for medical reference.

5. Troubleshooting

In case there is a problem when using the smart watch, please solve it accordingly to the
following steps. If the problem is not solved, please contact the seller or designated maintenance
personnel.

5.1 The watch cannot be turned on:

5.1.1 Press the display touch area for over 3 seconds.

5.1.2 Make sure there is enough battery. Battery power may be too low, please charge it.

5.1.3 If the smartwatch has not been used for a long time and the normal charger does not
respond, please try charging it with an output power of 5V/1A.

5.2 It shuts down automatically:

5.2.1 Battery power may be too low, please charge it.

5.3 Short battery life:

5.3.1 It may occur when the battery has not been fully charged, please ensure the is enough
time for charging (at least 2 hours is required).

5.3.2 Charger or data cable may not work properly, please change to new ones.

5.3.3 Please check the port of the data cable and try again to ensure a proper connection.

5.4 Bluetooth disconnects or unable to connect:

5.4.1 Please restart it.

 5.4.2 Please turn off Bluetooth of mobile phone and open it to reconnect.

5.5 Inaccurate sleep data:

The sleep monitor is designed to mimic the natural pattern of falling asleep and waking up.
Please use the smart watch during the day, otherwise a deviation may occur if you go to bed
late or only use it while you sleep. Sleep data may not be generated if you go to bed during
the day, since the default sleep time is set between 9:00 p.m. and 7:30 a.m.