Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Download as xlsx, pdf, or txt
Download as xlsx, pdf, or txt
You are on page 1of 6

DESIGN OF BUILT-UP COLUMN

1 Design parameters
Factored Load 220 KN/m2
Axial Load 161.3333 KN/m2
Grade of Steel 250 N/mm2

Area required 645.3333 mm2

SECTION USED: ISMB150 IS 808:1989


Mass M= 15 kg/m
Area A= 19.1 mm2
Depth D= 150 mm
Width B f= 75 mm
Thickness of web t w= 5 mm
Thickness of flange t p= 8 mm
Moment of inertia about XX Ixx= 718 cm4
Moment of inertia about YY Iyy= 46.8 cm5
Radius of gyration from XX rx= 6.13 cm
Radius of gyration from YY ry= 1.76 cm
Length of section L= 3.9624 m

Area to be provided by thinner plate Required area- area of section


= 626.2333 mm2
Thickness of plate 10 mm provided
Considering square thinner plate
Size of plate 31.31167 mm
Provide 300 mm X 10 mm thinner plate

2 CHECK FOR OVERHANG


Length of plate - Width of flange
Overhang
20

= 11.25 mm < 12t 120


< 200
OK

Total area = Area of section + Area of plates


= 6019.1 mm2

For the section selected


Izz Ixx + Ah2 1.51E+08 mm4
Iyy Iyy + 2bH3/3 45046800 mm4

r= ryy= sqrt(Iyy/A)= 86.50998 mm

Effective length KL 3169.92 mm


KL/r 36.64225 <180 OK

Thickness = thickness of section + thickness of plate 160 mm

For KL/r 36.64225 & fy 250 N/mm2 INTERPOLATION FOR τc


From table 9© for buckling class "C" on interpolation (X1,Y1) 0.15 0.28
fcd 59 N/mm2 (X2,Y2) 0.25 0.36
(X,Y) 0.00 0.160

Design Load (Pd) A x Fcd 355126.9 N


355.1269 KN > 161.3333 KN

OK
DESIGN OF PURLIN

1 Details
height for slope 1.5 m Grade of steel 250 Mpa
Span of truss 10 m Ymo 1.1
spacing of column(L) 5m
spacing of purlin 1m
tanӨ 0.15
Ө 8.53

3 SECTION USED:
Depth 72 mm
Breadth 72 mm
Thickness 4 mm

2 Load Calculation
Dead load of CGI sheet 0.75 KN/m2
Self weight of purlin KN/m2
Total dead load 0.75 KN/m2
Live Load 0.75 KN/m2
Factored total load 2.25 KN/m2
2.25 KN/m
Load normal to sheeting 2.225111 KN/m2
Load parallel to sheeting 0.333736 KN/m2

Bending moments are


Mz WzL2/8 6.953473 KNm
2
My WyL /9 1.042926 KNm

Shear forces are


Fz WzL/2 5.562778 KN
Fy WyL/2 0.834341 KN

Section modulus
Zpz = Mz Ymo + 2.5 d.My Ymo
fy b. fy

= 42067.46 mm
DESIGN OF COLUMN BASE PLATE

1 DETAILS
a Grade of Steel
fy= 250 MPa
COLUMN
fu= 410 MPa

fyb= 250 MPa


BOLT 4.6
fub= 410 MPa

Grade of Concrete fck= 20 MPa

b SECTION USED:
COLUMN ISMC150
Depth 150 mm
Width 75 mm
Thickness of flange 5.7 mm
Thickness of web 9 mm
Area 213000 mm2

c FORCES ACTING
Factored Load 20 KN Mx 100
Axial Load Fz 14.66667 KN Moment My 100
Transverse Force Fx 57 KN Mz 0
Transverse Force Fy 24 KN

2 DESIGN OF BASE PLATE

Bearing strength of concrete= 0.45fck = 9 N/mm2


Factored Load 20 KN

Area of base plate required = Factored Load


0.45fck

= 2222.222 mm2

Let us provide square base plate then


Required dimension L=B= 47.14045 mm
Provided dimension L=B= 200 mm OK
Eccentricity, 150
ex = My/Fz = 5 mm
ey = Mx/Fz = 5 mm
ex/L = 0.02500 <1/6, Base plate in compression
ex/B = 0.02500 <1/6, Base plate in compression

Area provided= 40000 mm2


Projection are
a= 62.5 mm
b= 25 mm
Thickness of base plate = sqrt(2.5w(a2-0.3b2)Ymo/fy) > tf
= 28.60288 > 5.7
KNm
KNm
KNm

You might also like