Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 129 views

    Part No: CB-2: Can Bus Interface

    Uploaded by

    Night Shade
    The document provides information about a CAN Bus interface module called the CB-2. It detects vehicle speed and RPM signals from the CAN Bus system and outputs a speed pulse signal of approximately 1 pulse per mile and an RPM signal of 2 pulses per revolution. It uses the CAN Bus high and low wires to receive data and outputs speed and RPM signals on separate wires. It has LED indicators to show the status of detecting the vehicle type and receiving CAN Bus data.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Part No: CB-2: Can Bus Interface

    Uploaded by

    Night Shade
    129 views1 page
    The document provides information about a CAN Bus interface module called the CB-2. It detects vehicle speed and RPM signals from the CAN Bus system and outputs a speed pulse signal of approximately 1 pulse per mile and an RPM signal of 2 pulses per revolution. It uses the CAN Bus high and low wires to receive data and outputs speed and RPM signals on separate wires. It has LED indicators to show the status of detecting the vehicle type and receiving CAN Bus data.

    Original Title

    HMCAN001

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides information about a CAN Bus interface module called the CB-2. It detects vehicle speed and RPM signals from the CAN Bus system and outputs a speed pulse signal of approximately 1 pulse per mile and an RPM signal of 2 pulses per revolution. It uses the CAN Bus high and low wires to receive data and outputs speed and RPM signals on separate wires. It has LED indicators to show the status of detecting the vehicle type and receiving CAN Bus data.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    129 views1 page

    Part No: CB-2: Can Bus Interface

    Uploaded by

    Night Shade
    The document provides information about a CAN Bus interface module called the CB-2. It detects vehicle speed and RPM signals from the CAN Bus system and outputs a speed pulse signal of approximately 1 pulse per mile and an RPM signal of 2 pulses per revolution. It uses the CAN Bus high and low wires to receive data and outputs speed and RPM signals on separate wires. It has LED indicators to show the status of detecting the vehicle type and receiving CAN Bus data.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    Part No:no:

    Part HMCAN001
    CB-2

    CAN BUS INTERFACE


    Function

    The CAN Bus interface is designed to provide a vehicle speed signal & RPM signal for vehicles using a CAN Bus
    system. It is programmed to automatically detect the vehicle type and it will give a frequency output of
    approximately 1Hz per mph.

    Feature

    The CB-2 features built-in diagnostic LEDs to indicate CAN Bus status and speed pulse output to aid the installation
    process. After power-up:
    Stage 1: Both LEDs light for approx 1 second
    Stage 2: Green LED on while the CB-2 listens for CAN Bus data
    Stage 3: Red LED indicates CAN has been detected. CB-2 now detecting vehicle type
    Stage 4: Once vehicle type is determined the Green LED should pulse when vehicle is driven. Red LED should stay
    on.

    Please note: If LEDs do not follow the above sequence it is still advisable to drive the vehicle to see if a speed pulse
    signal is still actually being produced by the CB-2. It is possible that some vehicles will perform in a different manner.

    Fitting

    The CAN Bus uses two wires for data transmission. One is called CAN_HIGH and the other called CAN_LOW
    (sometimes marked as CAN+ and CAN- respectively). All connections should be made with an insulated solder
    joint. Do not cut the CAN Bus wires.

    Controller Area Network (CAN)

    approx: 53x30x10mm

    Module Information

    Wire Colours CAN Bus interface CB-2


    Colour I/O Function
    Black I Ground
    Red I Power +12V regulated ignition controlled supply
    Yellow I CAN High
    Blue I CAN Low
    Orange O Speed Pulse Output 12V
    Green O RPM

    Output specification
    Vehicle Speed Approximately 3600 pulses per mile
    Engine Speed 2 pulses per revolution

    Inputs
    Power +12v DC approx 30mA

    Hummingbird Electronics
    PO Box 210 Anna Bay NSW 2316
    1300 155 541
    www.hmbe.com.au

    You might also like