F-02 Tubing Tubing F-03

Contents

Tubing Selection F-04

Tubing Tubing Handling F-04

Gas Service F-05

Tubing Installation F-05

Types of Tubing F-05

Suggested Allowable Working Pressure for Tubing

Stainless Steel Tubing F-06

Carbon Steel Tubing F-08

Copper Tubing F-09

Alloy 400 Tubing F-10

Alloy C-276 Tubing F-11

Alloy 20 Tubing F-11

Alloy 600 Tubing F-12

Grade 2 Titanium Tubing F-12

SAF 2507 Super Duplex Tubing F-13

Alloy 825 Tubing F-13

Alloy 625 Tubing F-14

Pressure Ratings at Elevated Temperatures F-14

Ordering Information
Basic Ordering Number F-15

Ordering Number Description F-16

Tubing Tools
Tubing Tools

Tubing
Tubing
 F-03 Tubing Tubing F-04

Contents Tubing Selection

Proper selection, handling, and installation of tubing, when combined with proper selection of FITOK tube fittings, are
essential for reliable tubing systems.
The following variables should be considered when ordering tubing for use with FITOK tube fittings:
◎ Surface finish
Tubing Selection F-04
◎ Material
◎ Hardness
Tubing Handling F-04 ◎ Wall thickness

Gas Service F-05

Tubing Surface Finish
Tubing Installation F-05
Many ASTM specifications cover the above requirements, but they often are not very detailed on surface finish. For example,
ASTM A450, a general tubing specification, it is specified as below:
Types of Tubing F-05 12. Straightness and Finish
12.1 Finished tubes shall be reasonably straight and have smooth ends free of burrs. They shall have a workmanlike finish.
Suggested Allowable Working Pressure for Tubing Surface imperfections (Note) may be removed by grinding, provided that a smooth curved surface is maintained, and the
wall thickness is not decreased to less than that permitted by this or the product specification. The outside diameter at the
Stainless Steel Tubing point of grinding may be reduced by the amount so removed.
F-06
Note: An imperfection is any discontinuity or irregularity found in the tube.
Carbon Steel Tubing F-08
Material
Copper Tubing F-09 Our suggested ordering instructions for each type of tubing are shown under the respective tables.

Alloy 400 Tubing F-10

Hardness
Alloy C-276 Tubing F-11 The key to selecting proper tubing for use with metal FITOK tube fittings is that the tubing must be softer than the
fitting material. FITOK tube fittings are designed to work properly with the tubing that is suggested in the ordering
instructions.
Alloy 20 Tubing F-11

Alloy 600 Tubing F-12

Wall Thickness
Grade 2 Titanium Tubing F-12 The accompanying tables show working pressure of tubing in a wide range of wall thicknesses. Allowable working pressure
are calculated from S values as specified by ASME B31.3, Process Piping. FITOK tube fittings have been repeatedly tested in
SAF 2507 Super Duplex Tubing both the minimum and maximum wall thicknesses shown. FITOK tube fittings are not recommended for tube wall
F-13
thicknesses outside the ranges shown in the accompanying tables for each size.

Alloy 825 Tubing F-13

Alloy 625 Tubing F-14 Tubing Handling

It is important to properly handle the tubing in order to reduce the scratches and protect the surface finish.
◎ Tubing should never be dragged out of a tubing rack or across a rough surface.
Pressure Ratings at Elevated Temperatures F-14 ◎ Tube cutters or hacksaws should be sharp. Do not take deep cuts with each turn of the cutter or stroke of the saw.
◎ Remove burrs on the tube end which will be helpful for the tubing go through the ferrules without damaging the
ferrule sealing edge.
Basic Ordering Number F-15

Ordering Number Description F-16

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-03 Tubing Tubing F-04

Contents Tubing Selection

Proper selection, handling, and installation of tubing, when combined with proper selection of FITOK tube fittings, are
essential for reliable tubing systems.
The following variables should be considered when ordering tubing for use with FITOK tube fittings:
◎ Surface finish
Tubing Selection F-04
◎ Material
◎ Hardness
Tubing Handling F-04 ◎ Wall thickness

Gas Service F-05

Tubing Surface Finish
Tubing Installation F-05
Many ASTM specifications cover the above requirements, but they often are not very detailed on surface finish. For example,
ASTM A450, a general tubing specification, it is specified as below:
Types of Tubing F-05 12. Straightness and Finish
12.1 Finished tubes shall be reasonably straight and have smooth ends free of burrs. They shall have a workmanlike finish.
Suggested Allowable Working Pressure for Tubing Surface imperfections (Note) may be removed by grinding, provided that a smooth curved surface is maintained, and the
wall thickness is not decreased to less than that permitted by this or the product specification. The outside diameter at the
Stainless Steel Tubing point of grinding may be reduced by the amount so removed.
F-06
Note: An imperfection is any discontinuity or irregularity found in the tube.
Carbon Steel Tubing F-08
Material
Copper Tubing F-09 Our suggested ordering instructions for each type of tubing are shown under the respective tables.

Alloy 400 Tubing F-10

Hardness
Alloy C-276 Tubing F-11 The key to selecting proper tubing for use with metal FITOK tube fittings is that the tubing must be softer than the
fitting material. FITOK tube fittings are designed to work properly with the tubing that is suggested in the ordering
instructions.
Alloy 20 Tubing F-11

Alloy 600 Tubing F-12

Wall Thickness
Grade 2 Titanium Tubing F-12 The accompanying tables show working pressure of tubing in a wide range of wall thicknesses. Allowable working pressure
are calculated from S values as specified by ASME B31.3, Process Piping. FITOK tube fittings have been repeatedly tested in
SAF 2507 Super Duplex Tubing both the minimum and maximum wall thicknesses shown. FITOK tube fittings are not recommended for tube wall
F-13
thicknesses outside the ranges shown in the accompanying tables for each size.

Alloy 825 Tubing F-13

Alloy 625 Tubing F-14 Tubing Handling

It is important to properly handle the tubing in order to reduce the scratches and protect the surface finish.
◎ Tubing should never be dragged out of a tubing rack or across a rough surface.
Pressure Ratings at Elevated Temperatures F-14 ◎ Tube cutters or hacksaws should be sharp. Do not take deep cuts with each turn of the cutter or stroke of the saw.
◎ Remove burrs on the tube end which will be helpful for the tubing go through the ferrules without damaging the
ferrule sealing edge.
Basic Ordering Number F-15

Ordering Number Description F-16

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-05 Tubing Tubing F-06

Gas Service Suggested Allowable Working Pressure for Tubing

Gases (air, hydrogen, helium, nitrogen, etc.) have very small molecules that can escape through even the most minute Figures and tables are for reference only. No implication is made that these values can be used for design work. Applicable
leak path. Some surface defects on the tubing can provide such a leak path. As tube outside diameter (O.D.) increases, codes and practices in industry should be considered. ASME Codes are the successor to and replacement of ASA Piping Codes.
so does the likelihood of a scratch or other surface defect interfering with proper sealing. ◎ All pressures are calculated from equations in ASME B31.3, Process Piping. See factors for calculating working pressures in
The most successful connection for gas service will occur if all installation instructions are carefully followed and the accordance with ASME B31.1, Power Piping.
heavier wall thicknesses of tubing on the accompanying tables are selected.
◎ Calculations are based on maximum O.D. and minimum wall thickness, except as noted in individual tables.
A heavy-wall tube resists ferrule action more than a thin-wall tube, allowing the ferrules to coin out minor surface Example: 1/2 in. O.D.×0.035 in. wall thickness stainless steel tubing purchased to ASTM A269:
imperfections and grip the tube more firmly. Within the applicable suggested allowable working pressure table, O.D. Tolerance ±0.005 in. / Wall Thickness Tolerance ±10%
select a tube wall thickness whose working pressure is outside of the shaded areas. Calculations are based on 0.505 in.O.D.×0.0315 in. wall thickness tubing.
◎ No allowance is made for corrosion or erosion.

Tubing Installation Stainless Steel Tubing

T Table 1 — Fractional Seamless Tubing For Welded Tubing

Fractional, in. Metric, mm

R T T Allowable working pressures are calculated from an For welded and drawn tubing, a derating factor must be
L➀ L➀
Tube O.D. Tube O.D. S value of 20 000 psig (137.8 MPa) for ASTM A269 tubing applied for weld integrity:
T Tube O.D. 1/16 1/2 3 19 at -20 to 100°F (-28 to 37°C), as listed in ASME B31.3 and ◎ For double-welded tubing, multiply working pressure
L Required straight tube 1/8 23/32 6 21 ASME B31.1. by 0.85.
L

length (see tables) 3/16 3/4 8 23 ◎ For single-welded tubing, multiply working pressure
R Radius of tubing bend 1/4 13/16 10 25 by 0.80.
5/16 7/8 12 31
3/8 15/16 14
1/2 1 3/16 15
32
5/8 16 Tube Tube Wall Thickness, in.
1 1/4
3/4 18 O.D. 0.010 0.012 0.014 0.016 0.020 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134 0.156 0.188
7/8 1 5/16 20 (in.) Working Pressure, psig
34
1 1 1/2 22 1/16 5600 6800 8100 9400 12000
Tubing properly selected and handled, combined with 1 1/4 2 25 40 1/8 8500 10900
properly installed FITOK tube fittings, will give you a 1 1/2 2 13/32 28 46 3/16 5400 7000 10200
leaktight system and provide reliable service in a wide 2 3 1/4 30 50 1/4 4000 5100 7500 10200
variety of applications. ➀ Required straight tube length. 32 54 5/16 4000 5800 8000
For maximum assurance of reliable performance, use: 38 63 3/8 3300 4800 6500
◎ Properly selected and handled high-quality tubing 50 80 1/2 2600 3700 5100 6700
—such as provided by FITOK. 5/8 2900 4000 5200 6000
◎ FITOK tube fittings assembled in accordance with
Hydraulic Presetting Tools 3/4 2400 3300 4200 4900 5800
catalog instructions. 7/8 2000 2800 3600 4200 4800
A FITOK hydraulic presetting tool must be used to install
When installing fittings near tube bends, there must be 1 2400 3100 3600 4200 4700
FITOK tube fittings over 1 in. (25 mm). For tube fittings in 1
a sufficient straight length of tubing to allow the tube 1 1/4 2400 2800 3300 3600 4100 4900
1/4, 1 1/2, and 2 in. (28, 30, 32, 38, and 50 mm), a presetting
to be bottomed in the FITOK fitting (see tables). 1 1/2 2300 2700 3000 3400 4000 4900
tool can be used to preset ferrules onto the tubing tightly.
For more information about installation instructions, please Note: For gas service, select a tube thickness outside of the shaded area.
contact FITOK or our authorized distributors.

Types of Tubing
Available in TMP series and TCT series. Materials include stainless steel, duplex stainless steel or Nickel-based alloy.
Enhanced-316/316L, with Ni, Cr and Mo contents in close approximation to upper values in ASTM standard, are available.

◎ TMP series seamless straight-length tubing, pickled or bright annealed, external surface mechanically polished
◎ TCT series seamless coiled tubing, bright annealed, external surface mechanically polished

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-05 Tubing Tubing F-06

Gas Service Suggested Allowable Working Pressure for Tubing

Gases (air, hydrogen, helium, nitrogen, etc.) have very small molecules that can escape through even the most minute Figures and tables are for reference only. No implication is made that these values can be used for design work. Applicable
leak path. Some surface defects on the tubing can provide such a leak path. As tube outside diameter (O.D.) increases, codes and practices in industry should be considered. ASME Codes are the successor to and replacement of ASA Piping Codes.
so does the likelihood of a scratch or other surface defect interfering with proper sealing. ◎ All pressures are calculated from equations in ASME B31.3, Process Piping. See factors for calculating working pressures in
The most successful connection for gas service will occur if all installation instructions are carefully followed and the accordance with ASME B31.1, Power Piping.
heavier wall thicknesses of tubing on the accompanying tables are selected.
◎ Calculations are based on maximum O.D. and minimum wall thickness, except as noted in individual tables.
A heavy-wall tube resists ferrule action more than a thin-wall tube, allowing the ferrules to coin out minor surface Example: 1/2 in. O.D.×0.035 in. wall thickness stainless steel tubing according to ASTM A269:
imperfections and grip the tube more firmly. Within the applicable suggested allowable working pressure table, O.D. Tolerance ±0.005 in. / Wall Thickness Tolerance ±10%
select a tube wall thickness whose working pressure is outside of the shaded areas. Calculations are based on 0.505 in.O.D.×0.0315 in. wall thickness tubing.
◎ No allowance is made for corrosion or erosion.

Tubing Installation Stainless Steel Tubing

T Table 1 — Fractional Seamless Tubing For Welded Tubing

Fractional, in. Metric, mm

R T T Allowable working pressures are calculated from an For welded and drawn tubing, a derating factor must be
L➀ L➀
Tube O.D. Tube O.D. S value of 20 000 psig (137.8 MPa) for ASTM A269 tubing applied for weld integrity:
T Tube O.D. 1/16 1/2 3 19 at -20 to 100°F (-28 to 37°C), as listed in ASME B31.3 and ◎ For double-welded tubing, multiply working pressure
L Required straight tube 1/8 23/32 6 21 ASME B31.1. by 0.85.
L

length (see tables) 3/16 3/4 8 23 ◎ For single-welded tubing, multiply working pressure
R Radius of tubing bend 1/4 13/16 10 25 by 0.80.
5/16 7/8 12 31
3/8 15/16 14
1/2 1 3/16 15
32
5/8 16 Tube Tube Wall Thickness, in.
1 1/4
3/4 18 O.D. 0.010 0.012 0.014 0.016 0.020 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134 0.156 0.188
7/8 1 5/16 20 (in.) Working Pressure, psig
34
1 1 1/2 22 1/16 5600 6800 8100 9400 12000
Tubing properly selected and handled, combined with 1 1/4 2 25 40 1/8 8500 10900
properly installed FITOK tube fittings, will give you a 1 1/2 2 13/32 28 46 3/16 5400 7000 10200
leaktight system and provide reliable service in a wide 2 3 1/4 30 50 1/4 4000 5100 7500 10200
variety of applications. ➀ Required straight tube length. 32 54 5/16 4000 5800 8000
For maximum assurance of reliable performance, use: 38 63 3/8 3300 4800 6500 7500
◎ Properly selected and handled high-quality tubing 50 80 1/2 2600 3700 5100 6700
—such as provided by FITOK. 5/8 2900 4000 5200 6000
◎ FITOK tube fittings assembled in accordance with
Hydraulic Presetting Tools 3/4 2400 3300 4200 4900 5800
catalog instructions. 7/8 2000 2800 3600 4200 4800
A FITOK hydraulic presetting tool must be used to install
When installing fittings near tube bends, there must be 1 2400 3100 3600 4200 4700
FITOK tube fittings over 1 in. (25 mm). For tube fittings in 1
a sufficient straight length of tubing to allow the tube 1 1/4 2400 2800 3300 3600 4100 4900
1/4, 1 1/2, and 2 in. (28, 30, 32, 38, and 50 mm), a presetting
to be bottomed in the FITOK fitting (see tables). 1 1/2 2300 2700 3000 3400 4000 4900
tool can be used to preset ferrules onto the tubing tightly.
For more information about installation instructions, please 2 2000 2200 2500 2900 3600
contact FITOK or our authorized distributors. Note: For gas service, select a tube thickness outside of the shaded area.

Types of Tubing
Available in TMP series and TCT series. Materials include stainless steel, duplex stainless steel or Nickel-based alloy.
Enhanced-316/316L, with Ni, Cr and Mo contents in close approximation to upper values in ASTM standard, are available.

◎ TMP series seamless straight-length tubing, pickled or bright annealed, external surface mechanically polished
◎ TCT series seamless coiled tubing, bright annealed, external surface mechanically polished

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-07 Tubing Tubing F-08

Suggested Ordering Information Carbon Steel Tubing

High-quality, fully annealed (Type 304/304L, 316/316L) (seamless or welded and drawn) stainless steel hydraulic tubing, ASTM
Table 3 — Fractional
A269 or A213, or equivalent. Hardness not to exceed 90 HRB or 200 HV. Tubing to be free of scratches, suitable for bending
and flaring. O.D. tolerances not to exceed ±0.003 in. for 1/16 in. O.D. tubing. Allowable working pressures are calculated from an S value of 15 700 psig (108.2 MPa) for ASTM A179 tubing at -20 to 100°F
Note: Certain austenitic stainless tubing has an allowable ovality tolerance double the O.D. tolerance and may not fit into (-28 to 37°C), as listed in ASME B31.3. For working pressure in accordance with ASME B31.1, multiply by 0.85.
FITOK precision tube fittings. Dual-certified grades such as 304/304L and 316/316L meet the minimum chemistry and
the mechanical properties of both alloy grades.
Tube Tube Wall Thickness, in.
O.D. 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134 0.148 0.165 0.180 0.220
(in.) Working Pressure, psig
Table 2—Metric Seamless Tubing For Welded Tubing 1/8 8000 10200
Allowable working pressures are based on equations For welded and drawn tubing, a derating factor must 3/16 5100 6600 9600
be applied for weld integrity: 1/4 3700 4800 7000 9600
from ASME B31.3 for EN ISO 1127 tubing (D4, T4
5/16 3700 5500 7500
tolerance for 3 to 12 mm; D4, T3 tolerance 14 to 50 mm), ◎ For double-welded tubing, multiply working pressure
3/8 3100 4500 6200
using a stress value of 137.8 MPa (20 000 psig) and tensile by 0.85.
1/2 2300 3200 4500 5900
strength of 516.4 MPa (74 900 psig), as listed in ASME B31.3 ◎ For single-welded tubing, multiply working pressure
5/8 1800 2600 3500 4600 5300
and ASME B31.1. by 0.80. 3/4 2100 2900 3700 4300 5100
7/8 1800 2400 3200 3700 4300
1 1500 2100 2700 3200 3700 4100
1 1/4 1600 2100 2500 2900 3200 3600 4000 4600 5000
1 1/2 1800 2000 2400 2600 2900 3300 3700 4100 5100
Tube Tube Wall Thickness, mm
O.D. 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.5 4.0 4.5 5.0
Note: For gas service, select a tube thickness outside of the shaded area.
(mm) Working Pressure, bar Suggested Ordering Information
3 670 High-quality, soft annealed seamless carbon steel hydraulic tubing, ASTM A179 or equivalent. Hardness not to exceed
6 310 420 540 710 72 HRB or 130 HV. Tubing to be free of scratches, suitable for bending and flaring.
8 310 390 520
10 240 300 400 510 580 Table 4 — Metric
12 200 250 330 410 470
Allowable working pressures are based on equations from ASME B31.3 for DIN 2391 tubing, using a stress value of
14 160 200 270 340 380 430
113 MPa (16 300 psig) and tensile strength of 340 MPa (49 300 psig).
15 150 190 250 310 360 400
16 170 230 290 330 370 400
18 150 200 260 290 320 370 Tube Wall Thickness, mm
Tube
20 140 180 230 260 290 330 380 O.D. 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.5 4.0 4.5
22 140 160 200 230 260 300 340 (mm) Working Pressure, bar
25 180 200 230 260 290 320
3 630 790
28 180 200 230 260 280 330
6 290 370 460 590
30 170 180 210 240 260 310
8 270 330 430
32 160 170 200 220 240 290 330
10 210 260 330
38 140 160 190 200 240 270 310
12 170 210 270 330 380 420
50 150 180 210 240 270
14 150 180 230 280 320 350
15 140 170 210 260 290 330
Note: For gas service, select a tube thickness outside of the shaded area.
16 130 150 200 240 270 300 350
Suggested Ordering Information 18 140 170 210 240 270 310
20 120 160 190 210 240 270 310
High-quality, fully annealed (Type 304/304L, 316/316L) stainless steel tubing, EN ISO 1127 or equivalent. Hardness not to exceed 90 HRB or
22 110 140 170 190 210 240 280
200 HV. Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed ±0.076 mm for 3 mm O.D. tubing.
25 100 120 150 170 180 210 240 260
Note: Dual-certified grades such as 304/304L, 316/316L meet the minimum chemistry and the mechanical properties
of both alloy grades. 28 150 160 190 210 230 270
30 140 150 170 200 210 250
32 130 140 160 180 200 230 270
38 120 130 150 160 190 230 260

Note: For gas service, select a tube thickness outside of the shaded area.
Suggested Ordering Information

Tools and Accessories

Tools and Accessories

High-quality, soft annealed carbon steel tubing, DIN 2391 or equivalent. Hardness not to exceed 72 HRB or 130 HV.

Tubing
Tubing

Tubing to be free of scratches, suitable for bending and flaring.

 F-07 Tubing Tubing F-08

Suggested Ordering Information Carbon Steel Tubing

High-quality, fully annealed (Type 304/304L, 316/316L) (seamless or welded and drawn) stainless steel hydraulic tubing, ASTM
Table 3 — Fractional
A269 or A213, or equivalent. Hardness not to exceed 90 HRB or 200 HV. Tubing to be free of scratches, suitable for bending
and flaring. O.D. tolerances not to exceed ±0.003 in. for 1/16 in. O.D. tubing. Allowable working pressures are calculated from an S value of 15 700 psig (108.2 MPa) for ASTM A179 tubing at -20 to 100°F
Note: Certain austenitic stainless tubing has an allowable ovality tolerance double the O.D. tolerance and may not fit into (-28 to 37°C), as listed in ASME B31.3. For working pressure in accordance with ASME B31.1, multiply by 0.85.
FITOK precision tube fittings. Dual-certified grades such as 304/304L and 316/316L meet the minimum chemistry and
the mechanical properties of both alloy grades.
Tube Tube Wall Thickness, in.
O.D. 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134 0.148 0.165 0.180 0.220
(in.) Working Pressure, psig
Table 2—Metric Seamless Tubing For Welded Tubing 1/8 8000 10200
Allowable working pressures are based on equations For welded and drawn tubing, a derating factor must 3/16 5100 6600 9600
be applied for weld integrity: 1/4 3700 4800 7000 9600
from ASME B31.3 for EN ISO 1127 tubing (D4, T4
5/16 3700 5500 7500
tolerance for 3 to 12 mm; D4, T3 tolerance 14 to 50 mm), ◎ For double-welded tubing, multiply working pressure
3/8 3100 4500 6200
using a stress value of 137.8 MPa (20 000 psig) and tensile by 0.85.
1/2 2300 3200 4500 5900
strength of 516.4 MPa (74 900 psig), as listed in ASME B31.3 ◎ For single-welded tubing, multiply working pressure
5/8 1800 2600 3500 4600 5300
and ASME B31.1. by 0.80. 3/4 2100 2900 3700 4300 5100
7/8 1800 2400 3200 3700 4300
1 1500 2100 2700 3200 3700 4100
1 1/4 1600 2100 2500 2900 3200 3600 4000 4600 5000
1 1/2 1800 2000 2400 2600 2900 3300 3700 4100 5100
Tube Tube Wall Thickness, mm
O.D. 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.5 4.0 4.5 4.5
Note: For gas service, select a tube thickness outside of the shaded area.
(mm) Working Pressure, bar Suggested Ordering Information
3 670 High-quality, soft annealed seamless carbon steel hydraulic tubing, ASTM A179 or equivalent. Hardness not to exceed
6 310 420 540 710 72 HRB or 130 HV. Tubing to be free of scratches, suitable for bending and flaring.
8 310 390 520
10 240 300 400 510 580 Table 4 — Metric
12 200 250 330 410 470
Allowable working pressures are based on equations from ASME B31.3 for DIN 2391 tubing, using a stress value of
14 160 200 270 340 380 430
113 MPa (16 300 psig) and tensile strength of 340 MPa (49 300 psig).
15 150 190 250 310 360 400
16 170 230 290 330 370 400
18 150 200 260 290 320 370 Tube Wall Thickness, mm
Tube
20 140 180 230 260 290 330 380 O.D. 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.5 4.0 4.5
22 140 160 200 230 260 300 340 (mm) Working Pressure, bar
25 180 200 230 260 290 320
3 630 790
28 180 200 230 260 280 330
6 290 370 460 590
30 170 180 210 240 260 310
8 270 330 430
32 160 170 200 220 240 290 330
10 210 260 330
38 140 160 190 200 240 270 310
12 170 210 270 330 380 420
Note: For gas service, select a tube thickness outside of the shaded area. 14 150 180 230 280 320 350
15 140 170 210 260 290 330
Suggested Ordering Information 16 130 150 200 240 270 300 350
18 140 170 210 240 270 310
High-quality, fully annealed (Type 304/304L, 316/316L) stainless steel tubing, EN ISO 1127 or equivalent. Hardness not to exceed 90 HRB or
20 120 160 190 210 240 270 310
200 HV. Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed ±0.076 mm for 3 mm O.D. tubing.
Note: Dual-certified grades such as 304/304L, 316/316L meet the minimum chemistry and the mechanical properties 22 110 140 170 190 210 240 280
of both alloy grades. 25 100 120 150 170 180 210 240 260
28 150 160 190 210 230 270
30 140 150 170 200 210 250
32 130 140 160 180 200 230 270
38 120 130 150 160 190 230 260

Note: For gas service, select a tube thickness outside of the shaded area.
Suggested Ordering Information

Tools and Accessories

Tools and Accessories

High-quality, soft annealed carbon steel tubing, DIN 2391 or equivalent. Hardness not to exceed 72 HRB or 130 HV.

Tubing
Tubing

Tubing to be free of scratches, suitable for bending and flaring.

 F-09 Tubing Tubing F-10

Copper Tubing Alloy 400 Tubing

Allowable working pressures are calculated from an S value of 6000 psig (41.3 MPa) for ASTM B75 (B75M) Allowable working pressures are calculated from an S value of 18 700 psig (128.9 MPa) for ASTM B165 tubing at -20 to 100°F
tubing at -20 to 100°F (-28 to 37°C), as listed in ASME B31.3 and ASME B31.1. (-28 to 37°C), as listed in ASME B31.3 and ASME B31.1.

Table 5 — Fractional
Table 7 — Fractional

Tube Tube Wall Thickness, in.

Tube Tube Wall Thickness, in.
O.D. 0.028 0.030 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134
O.D. 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120
(in.) Working Pressure, psig (in.) Working Pressure, psig
1/8 2700 3000 3600
1/8 7900 10 100
3/16 1800 1900 2300 3400
1/4 3700 4 800 7000 9500
1/4 1300 1400 1600 2500 3500
5/16 3 700 5400 7300
5/16 1300 1900 2700
3/8 3 100 4400 6100
3/8 1000 1600 2200
1/2 2 300 3200 4400
1/2 800 1100 1600 2100
3/4 2200 3000 4000 4600
5/8 900 1200 1600 1900
1 2200 2900 3400 3900 4300
3/4 700 1000 1300 1500 1800
7/8 600 800 1100 1300 1500
Note: For gas service, select a tube thickness outside of the shaded area.
1 500 700 900 1100 1300 1500
1 1/8 600 800 1000 1100 1300 1400

Note: For gas service, select a tube thickness outside of the shaded area. Table 8 — Metric

Tube Tube Wall Thickness, mm

Table 6 — Metric 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0
O.D.
(mm) Working Pressure, bar

Tube Wall Thickness, mm 6 310 390 490 620

Tube
8 290 350 450
O.D. 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0
(mm) 10 220 280 350
Working Pressure, bar
12 180 230 290
6 110 140 170 220
14 160 190 240 270
8 100 120 160
18 150 200 240 270 300
10 80 100 130
20 180 210 240 270 290
12 60 80 100 130 140
25 170 190 210 240 270 290
14 50 60 90 110 120 130
15 60 80 100 110 120 Note: For gas service, select a tube thickness outside of the shaded area.
16 70 90 100 110 120
18 60 80 90 100 110
20 60 70 80 90 100 110
Suggested Ordering Information
22 50 60 70 80 90 100 High-quality, fully annealed seamless alloy 400 hydraulic tubing, ASTM B165 or equivalent. Hardness not
25 40 50 60 70 80 90 100 to exceed 75 HRB or 137 HV. Tubing to be free of scratches, suitable for bending and flaring. O.D. toler-
28 40 50 60 70 80 90 ances not to exceed ±0.005 in (±0.13 mm).

Note: For gas service, select a tube thickness outside of the shaded area.

Suggested Ordering Information

High-quality, soft annealed seamless copper tubing, ASTM B75 (B75M) or equivalent. Also soft annealed
(Temper O) copper water tube, type K or type L to ASTM B88 .

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-09 Tubing Tubing F-10

Copper Tubing Alloy 400 Tubing

Allowable working pressures are calculated from an S value of 6000 psig (41.3 MPa) for ASTM B75 (B75M) Allowable working pressures are calculated from an S value of 18 700 psig (128.9 MPa) for ASTM B165 tubing at -20 to 100°F
tubing at -20 to 100°F (-28 to 37°C), as listed in ASME B31.3 and ASME B31.1. (-28 to 37°C), as listed in ASME B31.3 and ASME B31.1.

Table 5 — Fractional
Table 7 — Fractional

Tube Tube Wall Thickness, in.

Tube Tube Wall Thickness, in.
O.D. 0.028 0.030 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134
O.D. 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120
(in.) Working Pressure, psig (in.) Working Pressure, psig
1/8 2700 3000 3600
1/8 7900 10 100
3/16 1800 1900 2300 3400
1/4 3700 4 800 7000 9500
1/4 1300 1400 1600 2500 3500
5/16 3 700 5400 7300
5/16 1300 1900 2700
3/8 3 100 4400 6100
3/8 1000 1600 2200
1/2 2 300 3200 4400
1/2 800 1100 1600 2100
3/4 2200 3000 4000 4600
5/8 900 1200 1600 1900
1 2200 2900 3400 3900 4300
3/4 700 1000 1300 1500 1800
7/8 600 800 1100 1300 1500
Note: For gas service, select a tube thickness outside of the shaded area.
1 500 700 900 1100 1300 1500
1 1/8 600 800 1000 1100 1300 1400

Note: For gas service, select a tube thickness outside of the shaded area. Table 8 — Metric

Tube Tube Wall Thickness, mm

Table 6 — Metric 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0
O.D.
(mm) Working Pressure, bar

Tube Wall Thickness, mm 6 310 390 490 620

Tube
8 290 350 450
O.D. 0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0
(mm) 10 220 280 350
Working Pressure, bar
12 180 230 290
6 110 140 170 220
14 160 190 240 270
8 100 120 160
18 150 200 240 270 300
10 80 100 130
20 180 210 240 270 290
12 60 80 100 130 140
25 170 190 210 240 270 290
14 50 60 90 110 120 130
15 60 80 100 110 120 Note: For gas service, select a tube thickness outside of the shaded area.
16 70 90 100 110 120
18 60 80 90 100 110
20 60 70 80 90 100 110
Suggested Ordering Information
22 50 60 70 80 90 100 High-quality, fully annealed seamless alloy 400 hydraulic tubing, ASTM B165 or equivalent. Hardness not
25 40 50 60 70 80 90 100 to exceed 75 HRB or 137 HV. Tubing to be free of scratches, suitable for bending and flaring. O.D. toler-
28 40 50 60 70 80 90 ances not to exceed ±0.005 in (±0.13 mm).

Note: For gas service, select a tube thickness outside of the shaded area.

Suggested Ordering Information

High-quality, soft annealed seamless copper tubing, ASTM B75 (B75M) or equivalent. Also soft annealed
(Temper O) copper water tube, type K or type L to ASTM B88 .

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-11 Tubing Tubing F-12

Alloy C-276 Tubing Alloy 600 Tubing

Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of
20 000 psig (137.8 MPa). 20 000 psig (137.8 MPa).

Table 9 — Fractional Table 10 — Metric Table 13 — Fractional Table 14 — Metric

Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm Tube Wall Thickness, in. Tube Wall Thickness, mm
Tube Tube
O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5
(in.) Working Pressure, psig (mm) Working Pressure, bar (in.) (mm)
Working Pressure, psig Working Pressure, bar
1/4 4000 5100 7500 1 0200 6 310 420 520 670 1/4 4000 5100 7500 10200 6 310 420 520 670
5/16 4000 5800 7 800 8 310 390 500 3/8 3300 4800 6500 10 240 300 380
3/8 3300 4800 6 500 10 240 300 380 1/2 2600 3700 5100 12 200 240 310
1/2 2600 3700 5 100 12 200 240 310
Note: For gas service, select a tube Note: For gas service, select a tube
Note: For gas service, select a tube Note: For gas service, select a tube thickness outside of the shaded area. thickness outside of the shaded area.
thickness outside of the shaded area. thickness outside of the shaded area.
Suggested Ordering Information
Suggested Ordering Information
High-quality, fully annealed, cold drawn #1 temper alloy 600 seamless alloy tubing, ASTM B167 or equivalent. Hardness not
High-quality, fully annealed alloy C-276 tubing, ASTM B622 or equivalent. Hardness not to exceed 100 HRB or 248 HV. to exceed 92 HRB or 198 HV. Tubing to be free of scratches, suitable for bending and flaring. Order to outside diameter and
Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed ±0.005 in (±0.13 mm). wall thickness only, not to inside diameter, average wall specification. O.D. tolerances not to exceed ±0.005 in (±0.13 mm).

Alloy 20 Tubing Grade 2 Titanium Tubing

Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of Allowable working pressures are based on equations from ASME B31.3 and a maximum S value of 16 700 psig (115.1 MPa) for
20 000 psig (137.8 MPa). ASTM B338 tubing at -20 to 100°F (-28 to 37°C). For working pressure in accordance with ASME B31.1, multiply by 0.85.

Table 11 — Fractional Table 12 — Metric Table 15 — Fractional Table 16 — Metric

Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm Tube Wall Thickness, in. Tube Wall Thickness, mm
Tube Tube
O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5
(in.) Working Pressure, psig (mm) Working Pressure, bar (in.) (mm)
Working Pressure, psig Working Pressure, bar
1/4 4000 5100 7500 1 0200 6 310 420 520 670 1/4 3500 4500 6700 9100 6 290 380 470 600
3/8 3300 4800 6 500 10 240 300 380 3/8 2900 4200 5800 10 210 260 340
1/2 2600 3700 5 100 12 200 240 310 1/2 2100 3100 4200 12 180 220 280

Note: For gas service, select a tube Note: For gas service, select a tube Note: For gas service, select a tube Note: For gas service, select a tube
thickness outside of the shaded area. thickness outside of the shaded area. thickness outside of the shaded area. thickness outside of the shaded area.

Suggested Ordering Information Suggested Ordering Information

High-quality, fully annealed seamless or welded and drawn alloy 20 tubing, ASTM B729, B468 or equivalent. Hardness High-quality, fully annealed seamless or welded and drawn grade 2 titanium tubing, ASTM B338 or equivalent. Tubing to be
not to exceed 95 HRB. Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed free of scratches, suitable for bending. O.D. tolerances not to exceed ±0.005 in (±0.13 mm).
±0.005 in (±0.13 mm).

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-11 Tubing Tubing F-12

Alloy C-276 Tubing Alloy 600 Tubing

Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of
20 000 psig (137.8 MPa). 20 000 psig (137.8 MPa).

Table 9 — Fractional Table 10 — Metric Table 13 — Fractional Table 14 — Metric

Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm Tube Wall Thickness, in. Tube Wall Thickness, mm
Tube Tube
O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5
(in.) Working Pressure, psig (mm) Working Pressure, bar (in.) (mm)
Working Pressure, psig Working Pressure, bar
1/4 4000 5100 7500 1 0200 6 310 420 520 670 1/4 4000 5100 7500 10200 6 310 420 520 670
5/16 4000 5800 7 800 8 310 390 500 3/8 3300 4800 6500 10 240 300 380
3/8 3300 4800 6 500 10 240 300 380 1/2 2600 3700 5100 12 200 240 310
1/2 2600 3700 5 100 12 200 240 310
Note: For gas service, select a tube Note: For gas service, select a tube
Note: For gas service, select a tube Note: For gas service, select a tube thickness outside of the shaded area. thickness outside of the shaded area.
thickness outside of the shaded area. thickness outside of the shaded area.
Suggested Ordering Information
Suggested Ordering Information
High-quality, fully annealed, cold drawn #1 temper alloy 600 seamless alloy tubing, ASTM B167 or equivalent. Hardness not
High-quality, fully annealed alloy C-276 tubing, ASTM B622 or equivalent. Hardness not to exceed 100 HRB or 248 HV. to exceed 92 HRB or 198 HV. Tubing to be free of scratches, suitable for bending and flaring. Order to outside diameter and
Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed ±0.005 in (±0.13 mm). wall thickness only, not to inside diameter, average wall specification. O.D. tolerances not to exceed ±0.005 in (±0.13 mm).

Alloy 20 Tubing Grade 2 Titanium Tubing

Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of Allowable working pressures are based on equations from ASME B31.3 and a maximum S value of 16 700 psig (115.1 MPa) for
20 000 psig (137.8 MPa). ASTM B338 tubing at -20 to 100°F (-28 to 37°C). For working pressure in accordance with ASME B31.1, multiply by 0.85.

Table 11 — Fractional Table 12 — Metric Table 15 — Fractional Table 16 — Metric

Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm Tube Wall Thickness, in. Tube Wall Thickness, mm
Tube Tube
O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 O.D. 0.028 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5
(in.) Working Pressure, psig (mm) Working Pressure, bar (in.) (mm)
Working Pressure, psig Working Pressure, bar
1/4 4000 5100 7500 1 0200 6 310 420 520 670 1/4 3500 4500 6700 9100 6 290 380 470 600
3/8 3300 4800 6 500 10 240 300 380 3/8 2900 4200 5800 10 210 260 340
1/2 2600 3700 5 100 12 200 240 310 1/2 2100 3100 4200 12 180 220 280

Note: For gas service, select a tube Note: For gas service, select a tube Note: For gas service, select a tube Note: For gas service, select a tube
thickness outside of the shaded area. thickness outside of the shaded area. thickness outside of the shaded area. thickness outside of the shaded area.

Suggested Ordering Information Suggested Ordering Information

High-quality, fully annealed seamless or welded and drawn alloy 20 tubing, ASTM B729, B468 or equivalent. Hardness High-quality, fully annealed seamless or welded and drawn grade 2 titanium tubing, ASTM B338 or equivalent. Tubing to be
not to exceed 95 HRB. Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed free of scratches, suitable for bending. O.D. tolerances not to exceed ±0.005 in (±0.13 mm).
±0.005 in (±0.13 mm).

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-13 Tubing Tubing F-14

SAF 2507 Super Duplex Tubing Alloy 625 Tubing

Allowable working pressures are calculated from an S value of 38 700 psig (266.8 MPa) for ASTM A789 tubing at -20 to 100°F Allowable working pressures are calculated from an S value of 26 700 psig (184.1 MPa) for ASTM B444 Grade 2 tubing at
(-28 to 37°C), as listed in ASME B31.3. -20 to 100°F (-28 to 37°C) in accordance with ASME BPV 2001, tubing outside diameter and wall thickness tolerances from
ASTM B444 for small-diameter tube.
Table 17 — Fractional

Tube Wall Thickness, in. Table 20 — Fractional Table 21 — Metric

Tube
O.D. 0.035 0.049 0.065 0.083 0.095
(in.) Working Pressure, psig
Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm
1/4 10 000 15 000
O.D. 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 1.8
3/8 6 500 10 100 12 700 (in.) (mm)
Working Pressure, psig Working Pressure, bar
1/2 5 000 7 200 10 100 12 900
1/4 7300 10 700 14 600 6 470 610 750
5/8 5 800 7 600 10 100
3/8 4700 6 800 9 400 10 350 430 550
3/4 4 700 6 300 8 500 10 000
1/2 3500 5 000 6 800 12 290 350 450 550
Note: For gas service, select a tube thickness outside of the
shaded area. Suggested Ordering Information
High-quality, fully annealed seamless alloy 625 tubing, ASTM B444, Grade 1 or equivalent. Hardness not to exceed 25
HRC or 266 HV. Tubing to be free of scratches, suitable for bending and flaring.
Suggested Ordering Information
High-quality, fully annealed SAF 2507 super duplex tubing, ASTM A789 or equivalent. Hardness not to exceed 32 HRC. Note: For sizes not listed in the tables above, we recommend that a sample of the
Tubing to be free of scratches, suitable for bending and flaring. tubing and all pertinent information relating to system parameters be provided for
evaluation before installation. Give tubing sample and system information to any of
authorized FITOK distributors to forward to the factory.

Alloy 825 Tubing

Allowable working pressures are calculated from an S value of 23 300 psig (160.6 MPa) for ASTM B163 and ASTM B423
seamless tubing at -20 to 100°F (-28 to 37°C), For ASTM B704, Class 1 or equivalent welded and drawn tubing, multiply
working pressure by 0.85.
Pressure Ratings at Elevated Temperatures
Table 18 — Fractional Table 19 — Metric
Table 22 — Elevated Temperature Factors

Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm

Temperature Tubing Materials
O.D. 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 1.8
(in.) (in.) Alloy SAF Alloy
Working Pressure, psig Working Pressure, bar °F °C Copper Carbon 304/
➁
316/ Alloy Alloy Alloy
Ti Alloy
Steel ➀ 304L 316L➁ 400 20➂ C-276➂ 600➂ 2507 825 625
1/4 6400 9300 11 600 6 410 530 660
3/8 4100 5900 8 200 10 300 370 480 200 93 0.80 0.95 1.00 1.00 0.87 1.00 1.00 1.00 0.86 0.90 1.00 0.93
1/2 3000 4300 5 900 12 250 300 390 480 400 204 0.50 0.87➀ 0.93 0.96 0.79 0.96 0.96 0.96 0.61 0.82 0.90 0.85
600 315 0.82 0.85 0.79 0.85 0.85 0.85 0.45 0.80 0.84 0.79
800 426 0.76 0.79 0.75 0.79 0.79 0.79 0.81 0.75
Suggested Ordering Information
1000 537 0.69 0.76 0.76 0.35 0.73
High-quality, fully annealed seamless alloy 825 tubing, ASTM B163, ASTM B423, or equivalent. Fully annealed welded alloy
➀ Based on 375°F (190°C) max.
825 tubing, ASTM B704, class 1 or equivalent. Hardness not to exceed HR15T90 or 201 HV. Tubing to be free of scratches, ➁ Dual-certified grades such as 304/304L and 316/316L meet the minimum chemistry and the mechanical properties of both alloy grades.
suitable for bending and flaring. Wall thickness tolerances not to exceed ±10%. ➂ Based on the lower derating factor for stainless steel, in accordance with ASME B31.3.

To determine allowable working pressure at elevated temperatures, multiply allowable working pressures from Tables 1
through 21 by a factor shown in Table 22.
Example: Type 316/316L stainless steel 1/2 in. O.D. × 0.035 in. wall at 1000°F
1. The allowable working pressure at -20 to 100°F (-28 to 37°C) is 2600 psig (Table 1, page F-06).
2. The elevated temperature factor for 1000°F (537°C) is 0.76 (Table 22, above):
2600 psig × 0.76 = 1976 psig
The allowable working pressure for 316/316L 1/2 in. O.D. × 0.035 in. wall tubing at 1000°F (537°C) is 1976 psig.

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-13 Tubing Tubing F-14

SAF 2507 Super Duplex Tubing Alloy 625 Tubing

Allowable working pressures are calculated from an S value of 38 700 psig (266.8 MPa) for ASTM A789 tubing at -20 to 100°F Allowable working pressures are calculated from an S value of 26 700 psig (184.1 MPa) for ASTM B444 Grade 2 tubing at
(-28 to 37°C), as listed in ASME B31.3. -20 to 100°F (-28 to 37°C) in accordance with ASME BPV 2001, tubing outside diameter and wall thickness tolerances from
ASTM B444 for small-diameter tube.
Table 17 — Fractional

Tube Wall Thickness, in. Table 20 — Fractional Table 21 — Metric

Tube
O.D. 0.035 0.049 0.065 0.083 0.095
(in.) Working Pressure, psig
Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm
1/4 10 000 15 000
O.D. 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 1.8
3/8 6 500 10 100 12 700 (in.) (mm)
Working Pressure, psig Working Pressure, bar
1/2 5 000 7 200 10 100 12 900
1/4 7300 10 700 14 600 6 470 610 750
5/8 5 800 7 600 10 100
3/8 4700 6 800 9 400 10 350 430 550
3/4 4 700 6 300 8 500 10 000
1/2 3500 5 000 6 800 12 290 350 450 550
Note: For gas service, select a tube thickness outside of the
shaded area. Suggested Ordering Information
High-quality, fully annealed seamless alloy 625 tubing, ASTM B444, Grade 1 or equivalent. Hardness not to exceed 25
HRC or 266 HV. Tubing to be free of scratches, suitable for bending and flaring.
Suggested Ordering Information
High-quality, fully annealed SAF 2507 super duplex tubing, ASTM A789 or equivalent. Hardness not to exceed 32 HRC. Note: For sizes not listed in the tables above, we recommend that a sample of the
Tubing to be free of scratches, suitable for bending and flaring. tubing and all pertinent information relating to system parameters be provided for
evaluation before installation. Give tubing sample and system information to any of
authorized FITOK distributors to forward to the factory.

Alloy 825 Tubing

Allowable working pressures are calculated from an S value of 23 300 psig (160.6 MPa) for ASTM B163 and ASTM B423
seamless tubing at -20 to 100°F (-28 to 37°C), For ASTM B704, Class 1 or equivalent welded and drawn tubing, multiply
working pressure by 0.85.
Pressure Ratings at Elevated Temperatures
Table 18 — Fractional Table 19 — Metric
Table 22 — Elevated Temperature Factors

Tube Tube Wall Thickness, in. Tube Tube Wall Thickness, mm

Temperature Tubing Materials
O.D. 0.035 0.049 0.065 O.D. 0.8 1.0 1.2 1.5 1.8
(in.) (in.) Alloy SAF Alloy
Working Pressure, psig Working Pressure, bar °F °C Copper Carbon 304/
➁
316/ Alloy Alloy Alloy
Ti Alloy
Steel ➀ 304L 316L➁ 400 20➂ C-276➂ 600➂ 2507 825 625
1/4 6400 9300 11 600 6 410 530 660
3/8 4100 5900 8 200 10 300 370 480 200 93 0.80 0.95 1.00 1.00 0.87 1.00 1.00 1.00 0.86 0.90 1.00 0.93
1/2 3000 4300 5 900 12 250 300 390 480 400 204 0.50 0.87➀ 0.93 0.96 0.79 0.96 0.96 0.96 0.61 0.82 0.90 0.85
600 315 0.82 0.85 0.79 0.85 0.85 0.85 0.45 0.80 0.84 0.79
800 426 0.76 0.79 0.75 0.79 0.79 0.79 0.81 0.75
Suggested Ordering Information
1000 537 0.69 0.76 0.76 0.35 0.73
High-quality, fully annealed seamless alloy 825 tubing, ASTM B163, ASTM B423, or equivalent. Fully annealed welded alloy
➀ Based on 375°F (190°C) max.
825 tubing, ASTM B704, class 1 or equivalent. Hardness not to exceed HR15T90 or 201 HV. Tubing to be free of scratches, ➁ Dual-certified grades such as 304/304L and 316/316L meet the minimum chemistry and the mechanical properties of both alloy grades.
suitable for bending and flaring. Wall thickness tolerances not to exceed ±10%. ➂ Based on the lower derating factor for stainless steel, in accordance with ASME B31.3.

To determine allowable working pressure at elevated temperatures, multiply allowable working pressures from Tables 1
through 21 by a factor shown in Table 22.
Example: Type 316/316L stainless steel 1/2 in. O.D. × 0.035 in. wall at 1000°F
1. The allowable working pressure at -20 to 100°F (-28 to 37°C) is 2600 psig (Table 1, page F-06).
2. The elevated temperature factor for 1000°F (537°C) is 0.76 (Table 22, above):
2600 psig × 0.76 = 1976 psig
The allowable working pressure for 316/316L 1/2 in. O.D. × 0.035 in. wall tubing at 1000°F (537°C) is 1976 psig.

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-15 Tubing Tubing F-16

Basic Ordering Number

Standard

FC-01

F2 FC-02
Fractional Stainless Steel Seamless Tubing

BA 光亮退火
Condition
Tube Wall Basic Ordering Number Weight
O.D. Thickness

酸洗
(in.) (in.) 316/316L 304/304L lb/ft
0.035 SS-TMP-4-035- S4-TMP-4-035- 0.082
1/4
0.049 SS-TMP-4-049- S4-TMP-4-049- 0.107
0.049 SS-TMP-6-049- S4-TMP-6-049- 0.173

Fractional

盘管
10'

20'
3/8
0.065 SS-TMP-6-065- S4-TMP-6-065- 0.219
0.049 SS-TMP-8-049- S4-TMP-8-049- 0.240

Length

3M 3000 mm 10

6M 6000 mm 20

FT
1/2
0.065 SS-TMP-8-065- S4-TMP-8-065- 0.307
3/4 0.065 SS-TMP-12-065- S4-TMP-12-065- 0.484

盘管
Metric
1 0.083 SS-TMP-16-083- S4-TMP-16-083- 0.827
1 1/2 0.134 SS-TMP-24-134- S4-TMP-24-134- 1.989

M
SS - TMP - 6 - 049 - 20 - BA - F2

注：“型号说明”用于说明型号的组成规则，有些组合实际并不存在。如有疑问，请联系 FITOK 或授权代理商。

0.028"

0.035"

0.049"

0.065"

0.083"

0.095"

0.109"

0.120"

0.134"

0.156"

0.188"
Fractional
Metric Stainless Steel Seamless Tubing

Wall Thickness

028

035

049

065

083

095

109

120

134

156

188
0.8 mm

1.0 mm

1.2 mm

1.5 mm

1.8 mm

2.0 mm

2.2 mm

2.5 mm

2.8 mm

3.0 mm

3.5 mm

4.0 mm

4.5 mm
Tube Wall Basic Ordering Number Weight

Metric
O.D. Thickness
(mm) (mm) 316/316L 304/304L Kg/m

1.0

0.8

1.0

1.2

1.5

1.8

2.0

2.2

2.5

2.8

3.0

3.5

4.0

4.5
6 SS-TMP-6M-1.0- S4-TMP-6M-1.0- 0.125
8 1.0 SS-TMP-8M-1.0- S4-TMP-8M-1.0- 0.175
1.0 SS-TMP-10M-1.0- S4-TMP-10M-1.0- 0.226

1 1/4"

1 1/2"
Fractional
10

1/16"

3/16"

5/16"
1/8"

1/4"

3/8"

5/8"

3/4"

7/8"
1/2"
1.5 SS-TMP-10M-1.5- S4-TMP-10M-1.5- 0.320

1"

2"
1.5 SS-TMP-12M-1.5- S4-TMP-12M-1.5- 0.395

Tube O.D.
12

10

12

14

16

20

24

32
2.0 SS-TMP-12M-2.0- S4-TMP-12M-2.0- 0.501

8
1.5 SS-TMP-14M-1.5- S4-TMP-14M-1.5- 0.470

22M 22 mm
10M 10 mm

12M 12 mm

15M 15 mm

50M 50 mm
16M 16 mm
14M 14 mm

18M 18 mm

20M 20 mm

28M 28 mm

32M 32 mm

38M 38 mm
25M 25 mm

30M 30 mm
2 mm

3 mm

6 mm

8 mm
14

Metric
2.0 SS-TMP-14M-2.0- S4-TMP-14M-2.0- 0.602
1.5 SS-TMP-16M-1.5- S4-TMP-16M-1.5- 0.545
16

2M

3M

6M

8M
2.0 SS-TMP-16M-2.0- S4-TMP-16M-2.0- 0.702

① 仅适用于 TMP 系列 316/316L、304/304L。

1.5 SS-TMP-18M-1.5- S4-TMP-18M-1.5- 0.620
18

Ordering Number Description

2.0 SS-TMP-18M-2.0- S4-TMP-18M-2.0- 0.802
20 2.0 SS-TMP-20M-2.0- S4-TMP-20M-2.0- 0.903

Type

TMP
TCT
25 2.5 SS-TMP-25M-2.5- S4-TMP-25M-2.5- 1.410
28 2.5 SS-TMP-28M-2.5- S4-TMP-28M-2.5- 1.769
30 3.0 SS-TMP-30M-3.0- S4-TMP-30M-3.0- 2.031
32 3.5 SS-TMP-32M-3.5- S4-TMP-32M-3.5- 2.501
38 4.0 SS-TMP-38M-4.0- S4-TMP-38M-4.0- 3.410

高级-316/316L

2205 双相钢

2507 双相钢

合金 C-276
Material

316/316L

304/304L

合金 400

合金 600

合金 625

合金 825
Weight unit conversion:

合金 20
1 lb/ft=1.488 Kg/m 1 Kg/m=0.672 lb/ft

6Mo

A20

A65

A85
S12

INC

HC
D5

D7
SH
SS

SS

S4

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 F-15 Tubing Tubing F-16

Basic Ordering Number

Standard

FC-01

BA Annealing F2 FC-02

Note:"Ordering Number Description" is a reference to understand the combination rules of FITOK product part number. Not all combinations are available.
Fractional Stainless Steel Seamless Tubing

①
Condition
Tube Wall

Pickling
Basic Ordering Number Weight

Bright
O.D. Thickness
(in.) (in.) 316/316L 304/304L lb/ft
0.035 SS-TMP-4-035- S4-TMP-4-035- 0.082
1/4
0.049 SS-TMP-4-049- S4-TMP-4-049- 0.107
0.049 SS-TMP-6-049- S4-TMP-6-049- 0.173

Fractional

Coils
3/8

10'

20'
0.065 SS-TMP-6-065- S4-TMP-6-065- 0.219
0.049 SS-TMP-8-049- S4-TMP-8-049- 0.240

Length

3M 3000 mm 10

6M 6000 mm 20

FT
1/2
0.065 SS-TMP-8-065- S4-TMP-8-065- 0.307
3/4 0.065 SS-TMP-12-065- S4-TMP-12-065- 0.484

Metric

M Coils
1 0.083 SS-TMP-16-083- S4-TMP-16-083- 0.827
1 1/2 0.134 SS-TMP-24-134- S4-TMP-24-134- 1.989

SS - TMP - 6 - 049 - 20 - BA - F2

0.028"

0.035"

0.049"

0.065"

0.083"

0.095"

0.109"

0.120"

0.134"

0.156"

0.188"
Fractional
Metric Stainless Steel Seamless Tubing

Wall Thickness

028

035

049

065

083

095

109

120

134

156

188
0.8 mm

1.0 mm

1.2 mm

1.5 mm

1.8 mm

2.0 mm

2.2 mm

2.5 mm

2.8 mm

3.0 mm

3.5 mm

4.0 mm

4.5 mm
Tube Wall Basic Ordering Number Weight

Metric
O.D. Thickness
(mm) (mm) 316/316L 304/304L Kg/m

1.0

0.8

1.0

1.2

1.5

1.8

2.0

2.2

2.5

2.8

3.0

3.5

4.0

4.5
6 SS-TMP-6M-1.0- S4-TMP-6M-1.0- 0.125
8 1.0 SS-TMP-8M-1.0- S4-TMP-8M-1.0- 0.175
1.0 SS-TMP-10M-1.0- S4-TMP-10M-1.0- 0.226

1 1/4"

1 1/2"
Fractional
10

1/16"

3/16"

5/16"
1/8"

1/4"

3/8"

5/8"

3/4"

7/8"
1/2"
1.5 SS-TMP-10M-1.5- S4-TMP-10M-1.5- 0.320

1"

2"
1.5 SS-TMP-12M-1.5- S4-TMP-12M-1.5- 0.395

Tube O.D.
12

10

12

14

16

20

24

32
2.0 SS-TMP-12M-2.0- S4-TMP-12M-2.0- 0.501

① Applicable to 316/316L and 304/304L TMP series tubing.

1.5 SS-TMP-14M-1.5- S4-TMP-14M-1.5- 0.470

22M 22 mm
10M 10 mm

12M 12 mm

15M 15 mm

50M 50 mm
16M 16 mm

28M 28 mm

32M 32 mm
14M 14 mm

18M 18 mm

20M 20 mm

38M 38 mm
25M 25 mm

30M 30 mm
2 mm

3 mm

6 mm

8 mm
14

Metric
2.0 SS-TMP-14M-2.0- S4-TMP-14M-2.0- 0.602
1.5 SS-TMP-16M-1.5- S4-TMP-16M-1.5- 0.545
16

2M

3M

6M

8M
2.0 SS-TMP-16M-2.0- S4-TMP-16M-2.0- 0.702
1.5 SS-TMP-18M-1.5- S4-TMP-18M-1.5- 0.620
18

Ordering Number Description

2.0 SS-TMP-18M-2.0- S4-TMP-18M-2.0- 0.802
20 2.0 SS-TMP-20M-2.0- S4-TMP-20M-2.0- 0.903

Type

TMP
TCT
25 2.5 SS-TMP-25M-2.5- S4-TMP-25M-2.5- 1.410
28 2.5 SS-TMP-28M-2.5- S4-TMP-28M-2.5- 1.769
30 3.0 SS-TMP-30M-3.0- S4-TMP-30M-3.0- 2.031
32 3.5 SS-TMP-32M-3.5- S4-TMP-32M-3.5- 2.501

Enhanced-316/316L
(higher Cr, Ni and
38 4.0 SS-TMP-38M-4.0- S4-TMP-38M-4.0- 3.410

2205 Duplex

2507 Duplex
Mo content)

Alloy C-276
Material
Weight unit conversion:

Alloy 400

INC Alloy 600

A65 Alloy 625

A85 Alloy 825

316/316L

304/304L

A20 Alloy 20
1 lb/ft=1.488 Kg/m 1 Kg/m=0.672 lb/ft

S12 6Mo

HC
D5

D7
SH
SS

SS

S4

Tools and Accessories

Tools and Accessories

Tubing
Tubing
 Automatic Control Ball Valves
BF, BFH, BH, BO, BP, BV Series

info@fitokgroup.com
www.fitokgroup.com
FK-IC-GT-01-EN-200819

www.fitokgroup.com