USB OTOSCOPE

eheV3-USBOT

USER’S MANUAL
INTRODUCTION
FUNCTIONS AND APPLICATIONS
The USB OTOSCOPE is an electronic health care product for the home
and clinic. It is a tubular imaging system consisting of an optical lens, an
image sensor, an illumination mechanism, and an image transfer control
circuit connected to a computer. You can display the images captured by the
USB OTOSCOPE on the computer screen, store them on the computer, print
them, or send them over the Internet.
As an otoscope, it can be used to observe the eardrum.
As a telemedicine tool for frequent observation and knowing what your
body looks like in its normal, healthy state make you more alert to any
abnormalities and will lead to early detection and treatment of illnesses.

ATTENTION
Before use of this product, please read the instructions in this manual to
ensure its correct use.

SAFETY INSTRUCTIONS
Before using this product, please carefully read the following safety
instructions.
1. The socket that the computer is plugged in must be properly grounded,
as the computer supplies power to this product. If in any doubt, please have a
professional electrician check and verify the grounding to ensure safety.
2. Never use this product in stormy weather.
3. This product contains delicate and precision components. Be gentle
when using it and avoid harsh handling or excessive force that may cause
damage to the product.
4. The temperature of the handle increases slightly during use and it feels a
little warm. This is normal. If the product is overheated and hot to the touch,
immediately cut off the power and contact us for repair.
5. Never leave the product on unattended. Unplug from the USB port after
use.
6. Do not disassemble this product. Disassembling this product will result in
irreparable damage. The company is not responsible for damage resulting

2
from disassembly of the product by the user. In case of any difficulties in
using the product, please contact us.
7. Keep this product out of reach of children.
8. Do not let this product come in direct contact with steam, vapor, water, or
liquids of any kind. Such contact can cause irreparable damage that is not
covered by warranty.
9. When not in use, put the handle in a tightly sealed box to avoid moisture
and decay. Damages resulting from improper storage are not covered by the
warranty.
10. Never use this product to examine the eyes.
11. The cable in this product have been strictly tested. To ensure safe use,
do not replace it.

SYSTEM REQUIREMENTS
For best picture quality, the following specifications are recommended:
1. Windows XP, Vista，Windows 7 or MAC version 10.4.2 to 10.5.2
2. 128M RAM or above
3. At least 2 USB port (For best effect, USB 2.0 port is recommended).
4. CD-ROM and a 40G or higher hard disc.

TECHNICAL SPECIFICATIONS
1. DSP: High Quality Digital Image Monarch Processor.
2. Sensor: high-quality 2.0 M pixel CMOS sensor
3. Resolution: 1600X1200
4. Interface: USB2.0.
5. Frame rate: 30 frames/sec (CIF and VGA).
6. Focal distance: 5mm to 35mm in front of the opening of specula
7. Magnification: 30X (at 10mm FOCUS and display on 17” screen by a
640X480 resolution)
8. Timing snap: 10 seconds
9. Dimension: 29 mm in diameter, 115mm in length (without specula)
10. Image freeze: just rap space bar

3
PACKING LIST
ITEM QTY.
USB OTOSCOPE 1
SPECULA 12
CD(WITH USER’S MENU AND SOFTWARE) 1
MODEL PACKAGE ITEM USB AV

SIZE 18.5 X 12.5 X 7

GIFT BOX QTY 1
WEIGHT 310g
eheV3-USBOT
SIZE 55 X 40 X 40
CARTON BOX QTY 40
WEIGHT 17Kg
SIZE SCALE: centimeters
The package may be changed without notice.

DIRECTIONS FOR USE

Properly connect the USB OTOSCOPE to the computer USB PORT and to
rotate the DIMMER on the USB cable to controls the brightness of the LED on
the USB OTOSCOPE.

4
Double click on the icon of “My PC” on the screen and then double click on
the icon of ‘Camera’. After a short while you should see the image captured
by the USB OTOSCOPE on the computer monitor.
If the picture was taken by PC camera instead of USB otoscope please close
the image window and to click on another camera icon.
The software named ‘ehe.exe’ is located on the CD. The software is made by
our company to provide basic function of USB otoscope. It is highly
recommended to copy it (JUST COPY NOT INSTALL) from the CD into your
computer. And then double click on the icon to RUN the software (without any
installing procedure).

OPEN IMAGE WINDOW

Double click on the icon ‘ehe.exe’ to open an image window on the screen.
After a few seconds the pen camera will
begin to take still image in the window. If
the picture came from your PC camera or
any other device please click on ‘Device’
on the top line of the image window and
open the pull down menu. Choose the
proper USB camera and close the pull
down menu.

5
Click on ‘OPTIONS’ and click on ‘VIDEO CAPTURE PIN’. Click one of image
window size in the drop-down menu and click on ‘OK’ to confirm.

IMAGE ORIENTATION
There is a logo on the surface of the USB
OTOSCOPE. It shows the image position up.

OTOSCOPE
By using the USB OTOSCOPE user can look into
ear and check the eardrum.
User must clean the ear canal by using a cotton swab before to check
the ear. The ear wax will smear the lens and cause the image fuzzy.

FOCUS
The focusing ring is at the handle of the USB
HANDHELD MICROSCOPE. When the
focusing ring is rotated it adjusted the distance
between lens and sensor for getting the clear
image.
Before you putting the specula into ear turn the focusing ring（Golden
color）to focus on an objective that is 10mm far from the specula
opening.
While looking at the eardrum user may move the focusing ring of the
USB OTOSCOPE slightly back and forth to get the best focus of the

6
image.

TAKE PHOTOS
Click on ‘option’ on the top of image window.
Then click on ‘high resolution’ in the drop-down menu to make sure
there is a tick mark here.
Close the drop-down menu.
Push down the button of the dimmer that located
on the USB cable to freeze an image.
Or click ‘snap’ on the top of image window to take
a photo.
The photos you have taken will be saved in the
computer and display an icon on the screen.
If your system could not freeze an image please
follow steps to make it works:
1, click on ‘file’ that is on the top of image window.
2, click on the ‘set photo folder’
3, designate the folder you want to save the photos
4, click OK to confirm
MORE WAYS TAKING PHOTOS
Click on ‘option’ on the top of image window.
Then click on ‘high resolution’ in the drop-down menu to make sure
there is no tick mark here.
Close the drop-down menu.
Now you get below functions:
IMAGE FREEZ
Please rap the space bar for freezing an image.
If you want to save this image you can rap the return key for saving the
image as a photo.
Rap the space bar again to activate the image window.
TIMING SNAP
Rap the F5 key to arouse a timing snap.
The snap will be delayed 10 seconds after the key was rapped
company with beep per second.

7
If you could not get a clear photo by push down the snap button the
timing snap may be a help.

RETURN KEY SNAP

Just rap return key to take a photo.
WARNING
The top line of the image window will be blue color while it works
properly. It will be changed into light blue when user operates on
background and the snap function will be lost during this color.
Just click any where inside of the image window to change it back to
blue.

TAKE VIDEOS
For taking a video:
1, click on ‘video capture’
2, click on ‘Set Time Limit’ and input how many seconds the video you
want to take and tick the ‘use time limit’
3, click on the ‘capture’ again
4, click on ‘start capture’
5, click on ‘OK’ to start to the record
The video will be taken and stop automatically when time out.
The video is an AVI format.
User may change the location to any folder like other documents.

POST-SALE SERVICES
LIMITATIONS AND EXCLUSIONS
Please keep all the receipts of your purchase in a safe place. You need to
produce the unaltered and original receipts to receive warranty coverage.
Otherwise, the warranty is voided.
The warranty only covers the product if it is used under normal operation
conditions. However, the following are not covered by the warranty:
Damages resulting from unauthorized disassembly or assembly of the
products by the customer
Damages caused by fitting of improper components to the product

8
Damages resulting from unauthorized attempts to repair or to alter the
product
Gross distortion, scratches, discoloration, or damage of the covering
Cracks, scratches, and mold spots on the lens.
COMS sensor is burned or apparently scratched
Damages to the PCB board (such as burned PCB board) due to misuse

REPAIR SERVICE CARD

Product model:
Date of repair
Customer’s name
phone number

Description of faults

Place of repair

Results

WARRANTY CARD
Name of customer Address of customer

Purchase date Customer phone number

Product model Labeling of Sales Company

Serial number