Technical Information: FAG Heating Rings
Technical Information: FAG Heating Rings
Technical Information: FAG Heating Rings
Maintenance
Products
TI No. WL 80-9 E May 2003
Description Handling
FAG heating rings are slotted rings that are made of a light The heating ring is heated to 200 to 300 °C by means of an
metal alloy. Their bore diameters and widths are designed in electric heating plate. The temperature at the bore must be
such a way that the inner rings of several cylindrical roller checked constantly. The bore diameter design ensures that the
bearing designs of the same size can be extracted with the heating ring sits on the bearing ring with a slight interference
same heating ring, see page 3. fit at 200 to 300 °C. The heating ring must be pushed onto
the bearing ring (wearing heat-insulated gloves) and clamped
Several slots in the circumference of the heating ring reduce its by means of the handles. To improve the exchange of heat, the
rigidity and thus enable a close fit on the bearing ring. Heat- inner ring raceway may be coated with silicone-free heat trans-
insulated handles make handling of the rings easier. fer paste before pushing on the heating ring.
FAG · 1
Handling · Comparison with Other Extraction Tools · Programme · Information
for an Offer · Manufacture · Accessories · Examples of How to Order
The clamped heating ring has to be rotated to check if the in- Manufacture
terference fit of the bearing ring has been eliminated; then the
heating ring can be withdrawn from the shaft together with In some cases, customers want to manufacture the heating
the bearing ring. The extracted inner ring must be removed rings themselves.
from the heating ring immediately to prevent it from being We recommend to make the heating rings of a heat-resistant
excessively heated. aluminium alloy, e. g. AlCuMgPbF38 (material no.
Problems may arise with fretting corrosion or cold weldings in WST 3.1645).
the inner ring seat. In such cases the temperature difference The dimensions of the heating rings for commonly used cylin-
between bearing ring and shaft generated by the heating ring drical roller bearing inner rings are indicated in this TI. The
may not suffice to extract the bearing ring, and the inner ring bore of the heating ring is machined to a Z10 fit correspond-
must be heated by means of an annular burner (see FAG Publ. ing to the inner ring raceway diameter. The handles should be
No. WL 80 100 „Mounting and Dismounting of Rolling made of round bar steel, with a diameter of 8 to 16 mm and a
Bearings“). length of 150 to 200 mm, depending on the ring size. The
handles must be heat-insulated. The number of slots in the
Frequent use of the heating ring may affect its roundness so circumference is determined by the outside diameter of the
that the exchange of heat is reduced to such an extent that the heating ring. We recommend:
inner ring cannot be extracted. Two or more bearing rings up to 300 mm 6 slots
shrunk onto the shaft side by side cannot be dismounted si- over 300 mm 10 slots
multaneously with one heating ring. The bearing rings must The depth of the slots should be at least 2/3 of the ring cross
be heated one by one and extracted separately. section.
The dimensional tables in this TI list FAG heating rings for Examples of How to Order FAG Heating Rings
the commonly used cylindrical roller bearing inner rings with
HEATING.RING312E
bore diameters ranging from 50 to 200 mm. On request we
(for cylindrical roller bearing inner rings of size 312E, suitable
also supply heating rings in other dimensions.
bearing designs are shown on page 3)
To prepare an offer we need the following information:
• Bearing code or dimensions of the inner rings The heating rings for special bearings are suffixed with the
• Shaft fits codes of these bearings, i.e. a number beginning with 5 or 8.
• Drawing of the mounting location HEATING.RING801634
• Approximate number of parts to be extracted per day (for the inner rings of FAG cylindrical roller bearings 801634)
FAG · 2
Cylindrical Roller Bearing Inner Rings that Can be Extracted with the
Heating Rings
Cylindrical Roller Bearing Inner Rings that commonly used cylindrical roller bearing designs NU, NJ and
Can be Extracted with the Heating Rings NUP as well as the inner rings of other designs of the same
bearing size. All the suitable cylindrical roller bearing designs
The dimensions of the heating rings are designed in such a are shown below.
way that they can be used to extract the inner rings of the
FAG · 3
FAG Heating Rings B
b
NU NJ NUP
dZ10
x d1 D
tn
bn
L
for inner rings of cylindrical roller bearings, e.g. NU, NJ and NUP
(more designs on page 3)
FAG · 4
FAG Heating Rings
FAG · 5
FAG Heating Rings B
b
NU NJ NUP
dZ10
x d1 D
tn
bn
L
for inner rings of cylindrical roller bearings, e.g. NU, NJ and NUP
(more designs on page 3)
FAG · 6
Notes
FAG · 7
Notes
FAG · 8
FAG Kugelfischer AG & Co. KG
Industrial Bearings and Services
Postfach 12 60 · D-97419 Schweinfurt
Georg-Schäfer-Straße 30 · D-97421 Schweinfurt
Service hotline: Tel. +49 2407 9149-99
E-mail: support@fis-services.de
www.fis-services.com
TI No. WL 80-9 E/97/5/03 · Printed in Germany by Weppert GmbH & Co. KG, Schweinfurt