MT - Office Structural CA Set

TYPICAL STRUCTURAL ABBREVIATIONS ALL ABBREVIATIONS SHOWN
ARE NOT NECESSARILY USED TYPICAL SYMBOLS LEGEND TYPICAL PLAN NOTES: GENERAL
A K 1. SEE ARCHITECTURAL DRAWINGS FOR ACTUAL SEA LEVEL ELEVATION RELATED TO DATUM ELEVATION THE FOLLOWING GENERAL NOTES CONSTITUTE A MAJOR PART OF THE PLANS AND SPECIFICATIONS. STRICT
ABOVE FINISH FLOOR AFF KIPS (1000 LBS) k WB-1 INDICATES WIND BRACE - SEE WIND BRACE ELEVATIONS. = 100'-0" SHOWN ON DRAWINGS. COMPLIANCE WITH THESE NOTES IS ESSENTIAL TO THE PROPER CONSTRUCTION OF THE BUILDING.
ADDITIONAL ADDN'L KIP PER LINEAR FOOT KLF 1. REFER TO THE PLAN NOTES, LOCATED IN THESE GENERAL NOTES, FOR APPLICATION OF DETAILS WHICH
• SEE PLAN FOR TOP OF STRUCTURAL CONCRETE (T.O.S.C.) ELEVATION.
ADJACENT
AGGREGATE
ADJ.
AGGR.
KIP PER SQUARE FOOT KSF TRUSS INDICATES TRUSS - SEE TRUSS ELEVATIONS. • T.O.S. EL. = BOTTOM OF METAL DECK ELEVATION SEE PLAN FOR TOP OF STEEL (T.O.S.) ELEVATION. ARE DESIGNATED AS "TYPICAL DETAILS" IN THIS SET OF DRAWINGS.
ALTERNATE ALT.
• T.O. WOOD EL. = TOP OF PLYWOOD DECK / TONGUE & GROOVE DECK ELEVATION. SEE PLAN FOR TOP DEVELOPER
L OF WOOD ELEVATION. 2. SLEEVES AND BLOCKOUTS REQUIRED FOR PASSAGE OF DUCTWORK, PIPING, DRAINS, CONDUIT, ETC., AND
ANCHOR BOLT A.B. Hines
INDICATES MOMENT CONNECTION - ANCHORS REQUIRED FOR ANCHORING EQUIPMENT AND PIPING ARE NOT GENERALLY INDICATED ON THE
AND & LIGHTWEIGHT CONCRETE LWT. CONC. 2200 Ross Avenue, Suite 4200W
SEE MOMENT CONNECTION DETAILS. 2. SHEET INDEX: STRUCTURAL DRAWINGS. THE CONTRACTOR SHALL DETERMINE SUCH REQUIREMENTS FROM OTHER Dallas, TX 75201
ANGLE L LIVE LOAD LL
THE DETAILS IN THE DRAWINGS, INCLUDING THOSE DRAWINGS REFERENCED BY THIS INDEX, WHICH SERIES DRAWINGS, SUBCONTRACTORS, AND SUPPLIERS AND SHALL COORDINATE THE LOCATIONS AND (972-716-2908 Corbin Eckel)
APPROVED APPD. LONGITUDINAL LONG.
ARE DESIGNATED AS "TYPICAL DETAILS", APPLY GENERALLY TO THE CONSTRUCTION IN ALL AREAS DETAILS FOR THESE ITEMS PRIOR TO FABRICATION OR CONSTRUCTION OF THE STRUCTURE. ANY
APPROXIMATE APPROX. LONG LEG HORIZONTAL LLH
INDICATES STEEL BEAM SPLICE - WHERE THE CONDITIONS ARE SIMILAR TO THOSE DESCRIBED IN THE DETAILS, REGARDLESS OF CONFLICTS BETWEEN THESE ITEMS AND THE BUILDING STRUCTURE SHALL BE BROUGHT TO THE ATTENTION 2800 Post Oak Blvd., 49th Floor
ARCHITECT ARCH. LONG LEG VERTICAL LLV Houston, TX 77056
SEE STRUCTURAL STEEL SIMPLE BEAM CONNECTION DETAILS SBX-1. WHETHER OR NOT THE DETAILS ARE SPECIFICALLY REFERENCED IN THE DRAWINGS. OF THE ARCHITECT FOR RESOLUTION.
ARCHITECTURAL ARCH'L. LOW POINT L.P. (713-621-8000 Juan Delgado)
ARCH'L. FINISH SURFACE A.F.S. 3. VERIFY, OR ESTABLISH, LOCATIONS AND DIMENSIONS OF ALL FRAMED OPENINGS RELATED TO EQUIPMENT
AT @ M OR DUCTWORK, INCLUDING INSULATION, IF ANY. WHERE SUBSTANTIAL RELOCATION OR RECONFIGURATION EQUITY PARTNERS
INDICATES STRUCTURE OVER VOID -
AIR CONDITIONER A/C MANUFACTURE(R) MFR. SEE EXPANSIVE CLAY SOIL DETAILS CES-1. SHEET LIST IS REQUIRED, SUBMIT A DRAWING TO THE ARCHITECT FOR REVIEW. McNair Interests
AIR HANDLING UNIT AHU MASONRY OPENING M.O. 109 N. Post Oak Lane, Suite 600
SHT. NO. SHEET NAME 4. LOCATE EXISTING REINFORCEMENT, USING APPROPRIATE IMAGING EQUIPMENT, PRIOR TO CUTTING OR Houston, TX 77024
MATERIAL MAT.
S101-OF ABBREVIATIONS, SYMBOLS AND PLAN NOTES DRILLING INTO EXISTING CONCRETE. DO NOT CUT OR DAMAGE EXISTING REINFORCEMENT. IF THE (Drew Steffen)
B MAXIMUM MAX.
MECHANICAL MECH. INDICATES THAT COLUMN STARTS UPWARD FROM THIS LEVEL. S102-OF GENERAL NOTES REQUIRED OPERATIONS MAKE DAMAGING EXISTING REINFORCING UNAVOIDABLE, INFORM ARCHITECT SO Mitsui Fudosan America
BACK FACE B.F. THAT THE CONDITION MAY BE EVALUATED AND ALTERNATIVE DIRECTIONS GIVEN.
BACK TO BACK B. TO B. MEZZANINE MEZZ. S103-OF GENERAL NOTES 1251 Avenue of the Americas, Suite 800
MIDDLE MID. S200A-OF LEVEL B3 FRAMING PLAN New York, New York 10020
BASEMENT BSMT. 5. MATERIALS OR PRODUCTS SUBMITTED FOR APPROVAL WHICH ARE NOT AS SPECIFIED IN THE DOCUMENTS
MINIMUM MIN. INDICATES THAT COLUMN STOPS AT THIS LEVEL. (David Leff)
BEAM BM. S200B-OF LEVEL B2 FRAMING PLAN SHALL BE ACCOMPANIED BY A CURRENT ES REPORT (BY ICC EVALUATION SERVICE, INC.) MATERIALS OR
MISCELLANEOUS MISC.
BEARING BRG. S200C-OF LEVEL B1 FRAMING PLAN
MOMENT M PRODUCTS THAT DO NOT HAVE AN ES REPORT INDICATING THE SUBSTITUTED MATERIAL OR PRODUCT TO OFFICE/RETAIL ARCHITECT
BELOW FINISH FLOOR BFF M.C. OR BE EQUAL TO THAT SPECIFIED, WILL NOT BE CONSIDERED.
MOMENT CONNECTION(S) S201-OF LEVEL 01 FRAMING PLAN 5G Studio Collaborative, LLC.
BETWEEN BTWN.
S202-OF LEVEL 02 FRAMING PLAN 1217 Main St., Suite 500
BEVEL (ED) BEV ('D) Dallas, TX 75202
BLOCK BLK. N S203-OF LEVEL 03 FRAMING PLAN (214-347-4982 Christine Robbins-Elrod)
BLOCKING
BLOCK-OUT
BLKG.
B.O.
NEAR FACE
NOMINAL
N.F.
NOM.
STRUCTURAL SYMBOLS S203A-OF LEVEL 3 SLAB REINFORCING DESIGN LOADS MASTER/MULTIFAMILY ARCHITECT
S204-OF LEVEL 04 FRAMING PLAN
BOTTOM BOT. NON-SHRINK N.S. THE FOLLOWING SYMBOLS ARE USED TO REPRESENT THE MATERIALS SHOWN ON THE 1. DEAD LOADS INCLUDE THE WEIGHT OF THE STRUCTURAL COMPONENTS AND ALLOWANCES FOR GFF Architects
BRACKET BRKT. S205-OF LEVEL 05 FRAMING PLAN
NOT IN CONTRACT N.I.C. STRUCTURAL DRAWINGS. SEE SPECIFICATIONS AND GENERAL NOTES FOR MATERIAL PERMANENT PARTITIONS, PERMANENT FIXTURES, FINISHES, ROOFING, MECHANICAL, ELECTRICAL, 2808 Fairmount St., Suite 300
BRICK LEDGE ELEVATION B.L.E. NOT TO SCALE N.T.S. QUALITIES REQUIRED. S206-OF LEVEL 06 FRAMING PLAN Dallas, TX 75201
PLUMBING AND FIRE PROTECTION MATERIALS SHOWN OR SPECIFIED.
BRIDGING BRDG. NUMBER NO. OR # S207-OF LEVEL 07 FRAMING PLAN (214-303-1500 Michael Reyes)
BUILDING BLDG. S208-OF LEVEL 08 FRAMING PLAN 2. LOADINGS FOR MECHANICAL ROOMS ARE BASED ON THE WEIGHTS OF ASSUMED EQUIPMENT, AS
BUILDING LINE B.L. O S209-OF LEVEL 09 FRAMING PLAN INDICATED ON THE MECHANICAL DRAWINGS (INCLUDING THE WEIGHT OF CONCRETE PADS, WHERE ZONING/ENTITLEMENT
ARCHITECTURAL FINISHED SURFACE INDICATED). ANY CHANGES IN TYPE, SIZE, LOCATION OR NUMBER OF PIECES OF EQUIPMENT SHOULD Baldwin Associates
ON CENTER O.C. S209A-OF LEVEL 09 SLAB REINFORCING 3904 Elm Street, Suite B
C A.F.S. BE REPORTED TO THE ARCHITECT FOR VERIFICATION OF THE ADEQUACY OF SUPPORTING MEMBERS
OPENING(S) OPNG(S). S210-OF LEVEL ROOF FRAMING PLAN Dallas, TX 75226
CANTILEVER CANT. OPPOSITE OPP. PRIOR TO THE PLACEMENT OF SUCH EQUIPMENT. (214-824-7949 Robert Baldwin)
S210A-OF LEVEL ROOF SLAB REINFORCING
CAST IRON C.I. OPPOSITE HAND O.H. CAST-IN-PLACE CONCRETE
CAST-IN-PLACE C.I.P. S220-OF BUILDING SECTIONS 3. DESIGN LIVE LOADING IS AS FOLLOWS:
OUTSIDE FACE O.F. GEOTECH
CEILING CLG. OUTSIDE DIAMETER O.D. S221-OF BUILDING SECTIONS ROOF ................................................................................................................................................... 20 PSF
ECS Southwest, LLP
CENTER LINE C.L. OUTSTANDING OSTG. S222-OF BUILDING SECTIONS OFFICES (NOT INCLUDING NON-PERMANENT PARTITIONS) ........................................................ 80 PSF
3033 Kellyway Drive, Suite 110
CENTER OF GRAVITY C.G. STRUCTURAL PRECAST CONCRETE PARTITION ALLOWANCE IN OFFICE AREAS...................................................................................... 20 PSF Carrollton, TX 75006
S223-OF BUILDING SECTION STAIRWAYS............................................................................................................................................. 100 PSF
CENTER TO CENTER C. TO C. P (972-392-3222 Siddharth Neekhra)
S230-OF MECHANICAL YARD PLANS AND DETAILS PUBLIC CORRIDORS.............................................................................................................................. 100 PSF
CHANNEL C
CLEAR OR CLEARANCE CLR. PAN P S301-OF EXPANSIVE CLAY SOIL DETAILS CORRIDORS ABOVE FIRST FLOOR..................................................................................................... 80 PSF CIVIL ENGINEER
COLUMN COL. PARALLEL PAR. SAND GRAVEL, OR LOW P.I. FILL S302-OF TYPICAL PIER DETAILS AND TOP OF PIER DETAILS AUTOMOBILE PARKING ........................................................................................................................ 40 PSF Kimley-Horn and Associates, Inc.
COMPRESSION C OR COMP. PARTITION PARTN. S303-OF TYPICAL SLAB-ON-GRADE DETAILS AUTOMOBILE PARKING WHEEL LOAD ............................................................................................... 3,000 LBS 13455 Noel Road, Two Galleria Office Tower, Suite 700
CONCRETE CONC. PENETRATION PEN. GARAGE IMPACT LOAD ...................................................................................................................... 6,000 LBS Dallas, TX 75240
PERPENDICULAR PERP. S304-OF TYPICAL FOUNDATION DETAILS ALL SLABS-ON-GRADE........................................................................................................................ 100 PSF (972-770-1300 Alex Rathbun)
CONCRETE MASONRY UNIT CMU
CONNECTION (S) CONN(S). PIECE PC. EARTH S305-OF FOUNDATION SECTIONS AND DETAILS STORAGE (LIGHT).................................................................................................................................. 125 PSF
CONTINUOUS CONT. PLATE PL. S306-OF FOUNDATION SECTIONS AND DETAILS MECHANICAL ROOM (MIN.) .................................................................................................................. 150 PSF LANDSCAPE ARCHITECT
CONTRACTOR CONTR. POINT PT. S307-OF FOUNDATION SECTIONS AND DETAILS ELEVATOR MACHINE ROOM................................................................................................................ 150 PSF SWA Group
CONTROL JOINT CT.J. POUNDS PER SQUARE FOOT P.S.F. TERRACE ROOF ............................................................................................................................ 100 PSF 2001 Irving Boulevard, Suite 157
ROCK S401-OF CONCRETE COLUMN SCHEDULE AND DETAILS
CONSTRUCTION CONST. POUNDS PER SQUARE INCH P.S.I. EXISTING STRUCTURE FLOOR LIVE LOAD ...................................................................................... 50 PSF Dallas, TX 75207
PRECAST CONCRETE P/C S402-OF CONCRETE SLAB SCHEDULE AND DETAILS (214-954-0016 Chuck McDaniel)
CONSTRUCTION JOINT C.J.
CORNER COR. PRE-ENGINEERED S403-OF CONCRETE BEAM SCHEDULE AND DETAILS 4. LIVE LOAD REDUCTIONS, WHERE PERMISSIBLE, ARE COMPUTED IN ACCORDANCE WITH THE
COVER PLATE COV. PL. BUILDING MANUFACTURER PEBM S404-OF P-T CONCRETE BEAM SCHEDULE AND DETAILS BUILDING CODE. STRUCTURAL
ARCHITECTURAL PRECAST CONCRETE
PRE-ENGINEERED Datum Engineers
S405-OF CONC 2-WAY FLAT SLAB W DROP PNL SCHED & DETAILS
METAL BUILDING PEMB 6. DESIGN WIND LOADING IS AS FOLLOWS (NOTE: PER ASCE 7-10, WIND LOADS ARE ULTIMATE. 6516 Forest Park Road
D S410-OF SECTIONS AND DETAILS Dallas, TX 75235
PREFABRICATED PREFAB. SERVICE LOADS MAY BE OBTAINED BY DIVIDING THE STATED LOADS BY 1.6.):
DETAIL DET. S411-OF SECTIONS AND DETAILS (214-358-0174 Rodolfo D'Arlach)
PRELIMINARY PRELIM. NON-SHRINK GROUT
DEAD LOAD DL PROJECTION PROJ. S412-OF SECTIONS AND DETAILS DESIGN WIND LOADING IS AS FOLLOWS:
DEFORMED BAR ANCHOR D.B.A. WIND LOADS LISTED ARE ULTIMATE LOADS IN ACCORDANCE WITH ASCE 7-10 MEP ENGINEER
S413-OF SECTIONS AND DETAILS
DIAGONAL DIAG. ME Engineers, Inc.
R S501-OF SHEAR WALL ELEVATIONS 1825 Market Center Blvd., Suite 600
DIAMETER DIA. SAND CEMENT GROUT WIND DESIGN OPTION 2 - <ANALYTICAL PROCEDURE>
RADIUS R S502-OF SHEAR WALL SECTIONS AND DETAILS Dallas, TX 75207
DIMENSION(S) DIM(S). BASIC WIND SPEED (3-SECOND GUST) ..................................................................................... 115 MPH
REINFORCED CONCRETE PIPE RCP (214-741-1589 Drew Shivley)
DOVETAIL DVTL. S503-OF SHEAR WALL SECTIONS AND DETAILS RISK CATEGORY........................................................................................................................... II
DOWNSPOUT DS. REINFORCE(ING) (ED) (MENT) REINF. S601-OF EXISTING BASEMENT DETAILS EXPOSURE CATEGORY................................................................................................................ B
REMAINDER REM. OR R STYROFOAM INTERNAL PRESSURE COEFFICIENT.......................................................................................... 0.18
ELEVATOR CONSULTANT
DRAWING(S) DWG(S). S610-OF EXISTING FLOOR OPENING
DOUBLE DBL. REQUIRE REQ. Persohn | Hahn Associates, Inc.
DOWEL(S) DWL(S). RETENTION SYSTEM RET. SYS. S610A-OF EXISTING FLOOR OPENING WALL PRESSURE/SUCTION 8612 Broad Meadow Lane
McKinney, TX 75071
REQUIRED REQ'D. S611-OF STEEL SECTIONS AND DETAILS INTERIOR ZONES - MORE THAN 6 FT FROM EDGE (ZONE 4)
EXISTING (972-832-4232 Tom Williams)
E RISER RIS. S612-OF CONCRETE REPAIR DETAILS 10 SQ. FT. ............................................................................................ +32/-32 PSF
ROOF RF. 100 SQ. FT. .......................................................................................... +28/-29 PSF
EACH EA. ROOF DRAIN R.D.
S613-OF RENOVATION DETAILS INTERIOR DESIGNER
≥500 SQ. FT. ........................................................................................ +23/-26 PSF
EACH FACE E.F. ROOF OPENING RF. OPNG. S620-OF EXISTING ROOF/TERRACE FRAMING AND DETAILS Rottet Studio
END ZONES - WITHIN 6 FT OF EDGE (ZONE 5) 808 Travis Street, Suite 100
EACH WAY E.W. ROOM RM. C.M.U. S621-OF TERRACE SECTIONS AND DETAILS 10 SQ. FT. ........................................................................................... +32/-58 PSF Houston, TX 77002
EDGE ANGLE OFFSET E.A.O. ROUND RND. S622-OF TERRACE SECTIONS AND DETAILS 100 SQ. FT. ......................................................................................... +28/-46 PSF (713-221-1830 x 6105 Anja Majkic)
ELECTRICAL ELEC. ≥500 SQ. FT. ....................................................................................... +23/-35 PSF
S623-OF TERRACE SECTIONS AND DETAILS
ELEVATION EL. S
ELEVATOR ELEV. S630-OF WIND BRACE ELEVATIONS AND DETAILS
WALL PARAPETS:
ENGINEER ENGR. SCHEDULE(D) SCHED. S640-OF SIMPLE BEAM CONNECTION DETAILS
BRICK INTERIOR ZONES - MORE THAN 6 FT FROM EDGE (ZONE 4)
ENTRANCE ENT. SECTION SECT.
10 SQ. FT. ............................................................................................ +95 PSF
EQUAL EQ. SHEAR V
100 SQ. FT. .......................................................................................... +79 PSF www.datumengineers.com | Co. Reg. No. F-2819
EQUIPMENT EQUIP. SHEET SHT. Dallas Austin San Antonio
≥500 SQ. FT. ........................................................................................ +65 PSF
EXPANSION EXP. SIDEWALK SW. 214-358-0174 512-469-9490 210-858-2880
END ZONES - WITHIN 6 FT OF EDGE (ZONE 5) Datum Project No. 19166
EXPANSION JOINT E.J. SIMILAR SIM. STRUCTURAL STEEL 10 SQ. FT. ............................................................................................ +122 PSF
EXISTING EXIST. SPACE SPA. DATE ISSUE TITLE
100 SQ. FT. .......................................................................................... +102 PSF
EXTERIOR EXT. SPECIFICATION(S) SPEC(S) 04/03/2020 SCHEMATIC DESIGN PRESENTATION
≥500 SQ. FT. ........................................................................................ +86 PSF
EXTRA STRONG X-STR. SPECIFIED SPEC'D. 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SQUARE FOOT (FEET) S.F. WOOD (CONTINUOUS) 3. SEE ARCHITECTURAL DRAWINGS FOR LOCATION OF FLOOR DROPS, FLOOR SLOPES, CURBS,
*LOAD IS LESS THAN MINIMUM 16PSF, ULTIMATE - USE FOR INTERPOLATION ONLY 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
F STANDARD STD. MISCELLANEOUS ELEVATIONS, DETAILS AND DIMENSIONS NOT SHOWN ON PLAN. 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
STEEL STL. INTERIOR PRESSURE ON STRUCTUAL ELEMENTS (SERVICE)....................................... 5 PSF 10/30/2020 ISSUE FOR PERMIT
FACE TO FACE F. TO F. STIFFENER STIFF. 12/18/2020 90% CONSTRUCTION DOCUMENTS
FABRICATOR FABR. STRAIGHT STR. WOOD (NON-CONTINUOUS) 4.
FAR SIDE F.S. STIRRUPS STIR. C1 COLUMN MARK, SEE SCHEDULE 01/25/2021 100% CONSTRUCTION DOCUMENTS
FIELD VERIFY (F.V.) 7. SEISMIC DESIGN DATA (IBC):

STRUCTURE STRUCT. RISK CATEGORY..............................................................................................................
II
FINISH(ED) FIN. STRUCTURAL STRUCT'L.
FINISHED FLOOR FIN. FL. PLYWOOD MAPPED SPECTRAL RESPONSE ACCELERATIONS, SS & S1................................... 0.095/0.052 RESERVED FOR REVIEWERS NOTES
SYMMETRICAL SYM. SITE CLASS.......................................................................................................................
C
FIREPROOF(ING) FP. SUBCONTRACTOR SUBCONTR. P1, D/S302-OF TOP OF PIER DETAIL
FLANGE FLG. SPECTRAL RESPONSE COEFFICIENTS SDS /SD1..................................................... 0.076/0.059
SUPPORT(S) SUPT(S). PIER TYPE, SEE PIER SCHEDULE SEISMIC DESIGN CATEGORY........................................................................................ A
FLOOR FL.
GLUE LAMINATED LUMBER (GLU-LAM) BASIC SEISMIC-FORCE-RESISTING SYSTEM.............................................................. ORDINARY CONCRETE
FLOOR DRAIN F.D. T SHEAR WALLS
FOUNDATION FDN.
TAPERED BEAM T.B. CENTERLINE OF PIERS NOT SPECIFICALLY LOCATED ON PLAN BY NOTE OR DIMENSION SHALL BE DESIGN BASE SHEAR..................................................................................................... 170K
TEMPERATURE TEMP. LOCATED ACCORDING TO THE FOLLOWING INFORMATION, U.N.O.: SEISMIC RESPONSE COEFFICIENT, CS....................................................................... 0.010
G MICRO LAMINATED LUMBER (MICRO-LAM) RESPONSE MODIFICATION FACTOR, R....................................................................... 4
TENSION T
GAGE OR GAUGE GA. TERRAZZO TERR. A. FREESTANDING COLUMNS: CENTERLINE OF THE COLUMN ANALYSIS PROCEDURE USED ........................................................................... EQUIVALENT LATERAL FORCE
GALVANIZED GALV. THICK THK. DEFLECTION AMPLIFICATION FACTOR....................................................................... 4
GALVANIZED IRON G.I. TONGUE & GROOVE T&G B. GRADE BEAMS AND WALLS: CENTERLINE OF THE GRADE BEAM OR WALL IN ONE DIRECTION,
GALVANIZED STEEL G.S. RTU GRID OR AS NOTED IN THE OTHER DIRECTION. AT CORNER CONDITIONS, CENTERLINES OF 8. SNOW LOADING (ASCE 7, SECTION 7):
TOP AND BOTTOM T&B ROOF TOP MECHANICAL UNIT ON PLAN
GENERAL CONTRACTOR G.C. ___# INTERSECTING GRADE BEAMS OR WALLS. GROUND SNOW LOAD............................................................................................ 5 PSF
TOP OF T.O.
GEN. CONTR. TOP OF BEAM T.O.B.
GOVERNMENT GOVT. TOP OF FOOTING T.O.F. C. COLUMNS EMBEDDED IN GRADE BEAMS OR WALLS (PILASTERS): CENTERLINE OF THE COLUMN 9. STACKS OF MATERIALS OR OTHER CONSTRUCTION LOADS PLACED ON THE STRUCTURE SHALL REV. DATE ISSUE TITLE
GRADE GR. TOP OF PIER T.O.P. NOT EXCEED THE STATED DESIGN LIVE LOAD FOR THE AREA AFFECTED UNLESS ADEQUATELY
.05 12/18/2020 Permit Set Update
GRADE BEAM GR. BM. TOP OF PIER CAP T.O.P.C. SHORED.
TOP OF RETAINING WALL T.R.W. BEAM BOTTOM CHORD BRACING ON PLAN
H
TOP OF STEEL T.O.S. 5. SEE ARCH'L. DWGS. FOR SIZES & LOCATIONS OF ROOF OPENINGS.
HEADED STUDS H.S. TOP OF STRUCTURAL CONCRETE T.O.S.C.
HEIGHT HT. TOP OF WALL T.O.W. 6. REPETITIVE MEMBERS SUCH AS PURLINS AND JOISTS SHALL BE EQUALLY SPACED BETWEEN
HIGH POINT H.P. TREAD TR. DIMENSIONED POINTS, U.N.O.
HOLLOW STRUCTURAL SHAPE HSS TUBE STEEL TS
HORIZONTAL HORIZ. TYPICAL TYP.
HOOK HK. 7. NOTE TO CONTRACTOR:
FIELD VERIFY ALL EXISTING DIMENSIONS & ELEVATIONS PRIOR TO FABRICATION
I U
OF MATERIALS AND CONSTRUCTION.
INFORMATION INFO. UNLESS NOTED OTHERWISE U.N.O.
INSIDE DIAMETER
INSIDE FACE
I.D.
I.F. V CODES & DESIGN SPECIFICATIONS
INTERIOR INT. VERTICAL VERT.
INTERMEDIATE INTERM. 1. BUILDING CODE: IBC 2015.
W 2. STRUCTURAL STEEL: AISC 360-10 "SPECIFICATIONS FOR STRUCTURAL STEEL BUILDINGS" AND AISC
J
WATERSTOP WS. 341-10 "SEISMIC PROVISIONS FOR STRUCTURAL STEEL BUILDINGS."
JOINT(S) JT(S). WATERPROOFING WPFG.
JOIST(S) JST(S). WELDED WIRE MESH W.W.M. 3. STRUCTURAL CONCRETE: "BUILDING CODE REQUIREMENTS FOR REINFORCED CONCRETE (ACI
WIND BRACE WB 318-14)," THE AMERICAN CONCRETE INSTITUTE.
WIND LOAD W.L.
WINDOW WDW. 4. STRUCTURAL MASONRY: "BUILDING CODE REQUIREMENTS FOR MASONRY STRUCTURES (ACI 530-13),"
WITH W/ THE AMERICAN CONCRETE INSTITUTE.
WORK POINT W.P.
WOOD WD. 5. STRUCTURAL WOOD: "NATIONAL DESIGN SPECIFICATION FOR WOOD CONSTRUCTION (NDS) WITH 2012
WROUGHT IRON W.I. SUPPLEMENT", THE AMERICAN FOREST AND PAPER ASSOCIATION.
MAPLE TERRACE
3001 MAPLE AVENUE
DALLAS, TEXAS, 75201
TYPICAL ABBREVIATIONS, SYMBOLS AND PLAN NOTES AS-1 ABBREVIATIONS, SYMBOLS AND
PLAN NOTES
190013
PROJECT NUMBER
S101-OF S H E E T N U M B E R
EXISTING CONDITIONS CONCRETE MIX CAST-IN-PLACE CONCRETE POST-TENSIONING REINFORCING - CONT.
1. FIELD VERIFY ALL RELEVANT DIMENSIONS AND CONDITIONS AT EXISTING STRUCTURES 1. PROVIDE CONCRETE HAVING THE FOLLOWING GENERAL CHARACTERISTICS: 1. CONSTRUCTION JOINTS IN BEAMS, SLABS AND WALLS SHALL ONLY OCCUR WITHIN 2'-0" OF 19. TENDON FORCES SHOWN ON THE DRAWINGS ARE EFFECTIVE FORCES AFTER ALL
PRIOR TO STARTING SHOP DRAWINGS AND THE CONSTRUCTION PROCESS IN THOSE MIDSPAN BETWEEN SUPPORTS. CONSTRUCTION JOINTS IN SOIL SUPPORTED SLABS-ON- IMMEDIATE AND LONG TERM LOSSES. THE LOSS OF STRESS IN POST- TENSIONED
AREAS. SUBMIT APPROPRIATE PLANS AND DETAILS REFLECTING THE FIELD VERIFIED 28-DAY MAX. GRADE SHALL BE WHERE SHOWN ON PLAN. SEE NOTES ON TYPICAL SLAB-ON-GRADE PRESTRESSING STEEL, DUE TO CREEP AND SHRINKAGE OF CONCRETE, STEEL
EXISTING CONDITIONS FOR THE ARCHITECT'S USE. STRENGTH SLUMP AGG. SIZE DETAIL 20B/S303-OF FOR LOCATING SLAB JOINTS. COLUMN PILASTERS ON THE SIDES OF RELAXATION, FRICTION, CURVATURE, SWEEP AROUND OPENINGS, ETC., SHALL BE
CLASS (PSI) (IN) TYPE (IN.) USAGE GRADE BEAMS AND WALLS SHALL BE CAST MONOLITHICALLY WITH THE GRADE BEAM OR CALCULATED BY SUPPLIER AND COMPENSATED FOR IN THE NUMBER OF TENDONS OR
2. EXISTING CONDITIONS WHICH REQUIRE MODIFICATIONS TO THE DESIGN OF THE WALL UNLESS SHOWN OTHERWISE. SUBMIT A DIAGRAM OF ALL PROPOSED STRANDS PROVIDED. BURSTING REINFORCEMENT REQUIRED TO RESIST BURSTING,
PROPOSED CONSTRUCTION SHALL BE IMMEDIATELY BROUGHT TO THE ATTENTION OF THE A 3000 5-7 HDRK 1 1/2 CASED DRILLED PIERS CONSTRUCTION JOINTS WHICH ARE NOT SPECIFICALLY SHOWN ON THESE DRAWINGS SPLITTING AND SPALLING FORCES INDUCED BY TENDON ANCHORAGES SHALL BE DEVELOPER
ARCHITECT. (REFER TO SPECIFICATIONS). DESIGNED AND FURNISHED BY THE POST-TENSIONING SUPPLIER. SUBMIT DESIGN Hines
B 4000 3-5 HDRK 1 GRADE BEAMS, SLABS-ON- CALCULATIONS SEALED BY A REGISTERED PROFESSIONAL ENGINEER. 2200 Ross Avenue, Suite 4200W
3. THE TESTING LABORATORY SHALL EXAMINE AND REPORT ON THE CONDITION OF GRADE,FOOTINGS 2. SLEEVES, MECHANICAL OPENINGS, CONDUITS, PIPES, RECESSES, DEPRESSIONS, CURBS Dallas, TX 75201
PORTIONS OF THE EXISTING STRUCTURE WHICH WILL BE ALTERED OR WHICH WILL AND ALL EMBEDDED ITEMS SHALL BE PROVIDED FOR AS SHOWN ON THE ARCHITECTURAL 20. UNLESS OTHERWISE INDICATED, THE EFFECTIVE FORCE SHALL APPLY AT THE POINT (972-716-2908 Corbin Eckel)
SUPPORT NEW FRAMING, WITH SPECIAL EMPHASIS ON THE FOLLOWING: C 5000 3-5 HDRK 1 FORMED SLABS, BEAMS, AND MECHANICAL DRAWINGS AND AS REQUIRED BY EQUIPMENT MANUFACTURERS. ALONG THE TENDON CALCULATED TO HAVE THE LEAST FORCE (GREATEST CUMULATIVE
MINIMUM CONCRETE BETWEEN SLEEVES SHALL BE 6". INSTALLATION OF THESE ITEMS LOSSES). FORCE AVERAGING IS NOT PERMITTED. 2800 Post Oak Blvd., 49th Floor
SLABS-ON-VOID BOXES Houston, TX 77056
A. EXISTING BOLTED CONNECTIONS: IDENTIFY MISSING, DAMAGED OR OTHERWISE SHALL BE COORDINATED WITH SHOP DRAWINGS OF TRADES REQUIRING THESE ITEMS. (713-621-8000 Juan Delgado)
DETERIORATED BOLTS AND CONNECTION PLATES. D 6000 3-5 HDRK 1 COLUMNS & SHEARWALLS LEVELS 21. TENDONS SHALL BE SECURED TO A SUFFICIENT NUMBER OF POSITIONING DEVICES TO
B3 TO L5, BASEMENT WALLS 3. SET FORMS TO FOLLOW SLOPES AND GRADES DEFINED ON PLAN, KEEPING MEMBER ENSURE CORRECT LOCATION DURING AND AFTER THE PLACING OF CONCRETE, AND SHALL
B. EXISTING WELDED CONNECTIONS: VERIFY THAT WELDS WERE COMPLETED AND ARE DEPTHS CONSTANT AT DEPTHS DETAILED OR SCHEDULED, UNLESS NOTED OTHERWISE. BE SUPPORTED AT A MAXIMUM OF 4'-0" ON CENTER. TWISTING OR ENTWINING OF EQUITY PARTNERS
STILL IN GOOD CONDITION, SUITABLE FOR SUPPORT OF ADDITIONAL LOADS SHOWN ON SLOPE UNIFORMLY BETWEEN ELEVATIONS GIVEN. BUILD IN CAMBER WHERE SPECIFIED. INDIVIDUAL TENDONS WITHIN A BUNDLE SHALL NOT BE PERMITTED. McNair Interests
E 5000 3-5 HDRK 1 COLUMNS & SHEARWALLS LEVELS 109 N. Post Oak Lane, Suite 600
DRAWINGS. L5 TO ROOF. Houston, TX 77024
4. ALL CONDUITS AND PIPES EMBEDDED IN CONCRETE SHALL COMPLY WITH ALL PROVISIONS 22. TENDONS SHALL CONFORM TO THE CONTROL POINTS SHOWN ON THE DRAWINGS AND (Drew Steffen)
C. GENERAL CONDITION OF FRAMING IN AREAS TO BE LOADED OR ALTERED. F 3000 3-5 LTWT ¾ DECK INFILLS SPECIFIED IN ACI 318, SECTION 20.7, WITH THE FOLLOWING SPECIFIC REQUIREMENTS: SHALL HAVE A PARABOLIC DRAPE UNLESS NOTED OTHERWISE. PROFILE DIMENSIONS
CONFIGURATION AND EVIDENCE OF EXCESSIVE CORROSION OR OTHER DAMAGE A. THE MAXIMUM OUTSIDE DIAMETER OF THE CONDUITS AND PIPES SHALL BE 3". NONE LOCATE THE CENTER OF GRAVITY OF TENDON STEEL OR TENDON GROUP (C.G.S.) Mitsui Fudosan America
SHALL BE REPORTED. PERMITTED IN SLABS THINNER THAN 4 1/2". MEASURED FROM THE MEMBER SOFFIT. LOW POINTS ARE AT MIDSPAN, UNLESS 1251 Avenue of the Americas, Suite 800
B. THE MINIMUM CLEAR DISTANCE BETWEEN CONDUITS AND PIPES SHALL BE 6". OTHERWISE SHOWN OR NOTED. New York, New York 10020
C. AT FORMED SLABS, LOCATE IN MIDDLE THIRD OF SLAB THICKNESS BETWEEN THE TOP (David Leff)
2. IN ADDITION TO THE CONCRETE PROPERTIES SCHEDULED ABOVE, THE
WATER/CEMENTITIOUS MATERIALS (W/C) RATIO FOR THE FOLLOWING CONCRETE AND BOTTOM MAT OF REINFORCING. AT BEAMS, LOCATE INSIDE BEAM STIRRUP. IN 23. STRESSING OPERATION SHALL BE OBSERVED BY THE TESTING LABORATORY. A RECORD
APPLICATIONS SHALL BE LIMITED TO THE MAXIMUM VALUES NOTED: JOISTS, LOCATE AT CENTER LINE, AT LEAST 6" FROM BOTTOM. OF ALL STRESSING FORCES AND FIELD MEASURED ELONGATIONS SHALL BE SUBMITTED TO OFFICE/RETAIL ARCHITECT
D. NONE PERMITTED IN SLABS-ON-GRADE WHICH WILL BE PERMANENTLY EXPOSED OR THE ARCHITECT WITHIN 48 HOURS. FIELD READINGS OF ELONGATIONS AND STRESSING 5G Studio Collaborative, LLC.
SUBSTITUTIONS A. SLABS ON VOID BOXES 0.50 SCHEDULED TO RECEIVE THIN SET TILE. PLACE ALL PIPES AND CONDUITS IN THE FILL
BENEATH THE VAPOR RETARDER. RECOMPACT AS SPECIFIED.
FORCES SHALL NOT VARY BY MORE THAN 7 PERCENT FROM CALCULATED VALUES SHOWN
ON THE SHOP DRAWINGS.
1217 Main St., Suite 500
Dallas, TX 75202
1. ALL REQUESTS FOR SUBSTITUTIONS OF MATERIALS OR DETAILS SHOWN IN THE CONTRACT (214-347-4982 Christine Robbins-Elrod)
3. EXCEPT FOR CONCRETE FOR DRILLED PIERS, WHOSE SLUMP LIMITS ARE ABSOLUTE, E. IN NON-EXPOSED SLABS-ON-GRADE, LIMIT SIZE TO 1 1/4" O.D. SPACE 12" APART AND
DOCUMENTS SHALL BE SUBMITTED FOR APPROVAL DURING THE BIDDING PERIOD. ONCE SLUMP LIMITS ARE BASED ON MIXES WITHOUT WORKABILITY ADMIXTURES, AND MAY BE TIE TO UNDERSIDE OF REINFORCING MAT. WHERE LINES CONVERGE AT SOURCE, 24. DO NOT CUT OFF TENDON ENDS UNTIL ALL TENDONS IN A GIVEN BAY HAVE BEEN
BIDS ARE ACCEPTED, PROPOSED SUBSTITUTIONS WILL BE CONSIDERED ONLY WHEN THEY DOUBLE UP THE SLAB REINFORCING IN THE CONVERGENCE ZONE AND 3'-0" BEYOND. SATISFACTORILY STRESSED AND THE ELONGATION RECORDS APPROVED. AVOID MASTER/MULTIFAMILY ARCHITECT
INCREASED WITH WORKABILITY ADMIXTURES, PROVIDED THAT BATCH PROPORTIONS ARE
ARE OFFICIALLY SUBMITTED WITH AN IDENTIFIED SAVINGS TO BE DEDUCTED FROM THE PLACE ALL LARGER LINES IN THE FILL BENEATH THE VAPOR RETARDER. OVERHEATING ANCHORS WHEN CUTTING TENDONS. FILL STRESSING POCKETS WITH GFF Architects
DETERMINED AND SUBMITTED IN THE MANNER DESCRIBED IN THE SPECIFICATIONS. WHEN 2808 Fairmount St., Suite 300
CONTRACT. A WORKABILITY ADMIXTURE IS USED, SLUMP SHALL CONFORM TO THE REQUIREMENTS OF
THE ACCEPTED MIX DESIGN, WHICH SHALL NOT EXCEED 8 INCHES (WITH A TOLERANCE OF
F. NONE PERMITTED IN COLUMNS WITHOUT PRIOR APPROVAL.
G. DO NOT DISPLACE REINFORCING STEEL FROM ITS PROPER POSITION.
SPECIFIED GROUT. FINISH TO MATCH SURROUNDING CONCRETE AT EXPOSED SURFACES.
FIELD DRILLED DOWELS AND ANCHOR Dallas, TX 75201
(214-303-1500 Michael Reyes)
25. TYPICAL POST-TENSIONING REINFORCING DETAILS ARE SHOWN ON SHEET S404-OF .
FIRE RESISTANCE
+0 AND -2.5 INCHES) AT TIME OF DISCHARGE.
5. SLEEVES OR PIPES PASSING HORIZONTALLY THROUGH BEAMS OR JOISTS MUST BE
LOCATED IN THE MIDDLE THIRD OF THE SPAN AND WITHIN THE MIDDLE THIRD OF THE BEAM 26. VERIFY ASSUMED WOBBLE AND CURVATURE COEFFICIENTS DURING TENDON STRESSING
RODS IN CONCRETE ZONING/ENTITLEMENT
4. SLUMP LIMITS APPLY AT THE TRUCK AT THE TIME OF DISCHARGE EXCEPT THAT PUMPED Baldwin Associates
1. THE STRUCTURAL SYSTEM AND CONSTRUCTION DETAILS ARE DESIGNED TO COMPLY WITH CONCRETE SHALL BE SAMPLED AT THE DISCHARGE END OF THE HOSE. DEPTH. MAXIMUM DIAMETER SHALL BE ONE THIRD OF THE MEMBER DEPTH. SPACE AT OPERATIONS. 1. FIELD DRILLED DOWELS AND ANCHOR RODS TO BE SET IN HARDENED CONCRETE SHALL
3904 Elm Street, Suite B
THE REQUIREMENTS OF THE FOLLOWING: LEAST 3 DIAMETERS CLEAR APART AND ADD ONE STIRRUP EACH SIDE OF EACH SLEEVE. BE ONE OF THE SYSTEMS LISTED HERE.
Dallas, TX 75226
5. FLY ASH WILL NOT BE PERMITTED IN ARCHITECTURALLY EXPOSED CONCRETE. FLY ASH (214-824-7949 Robert Baldwin)
FLOOR ASSEMBLY:
ROOF ASSEMBLY:
1 HOURS
1 HOURS
MAY BE USED ELSEWHERE, WITHIN THE SPECIFIED PROPORTION LIMITS, BUT THE
CONTRACTOR SHALL FIRST VERIFY COMPATIBILITY WITH CURING COMPOUNDS, SEALERS,
6. BACKFILL AGAINST BASEMENT WALLS SHALL NOT BE STARTED UNTIL THE FLOORS AT THE
BASE AND THE TOP OF THE WALL HAVE BEEN COMPLETED, TO BRACE THE WALL. CHIPPING, CUTTING, OR CORING INTO SET-XP EPOXY ANCHORING SYSTEM, SIMPSON STRONG-TIE CO., PLEASANTON, CA
PE1000+ STANDARD SET ADHESIVE ANCHORING SYSTEM, POWERS FASTENERS, GEOTECH
STRUCTURAL FRAME: 1 HOURS BREWSTER, NY
EXTERIOR BEARING WALLS: 1 HOURS
BOND BREAKER, FLOORING ADHESIVES AND OTHER MATERIALS PROPOSED TO BE IN
CONTACT WITH THE CONCRETE. 7. PROVIDE SHEAR KEYS IN ALL CONSTRUCTION JOINTS IN BEAMS AND WALLS, IN EXISTING HIT/HY200 ADHESIVE ANCHORING SYSTEM, HILTI FASTENING SYSTEMS, TULSA, OK
HIT-RE500 V3 OR HIT/HY2000, ADHESIVE ANCHORING SYSTEM, DEPENDING UPON THE
ECS Southwest, LLP
INTERIOR BEARING WALLS: 1 HOURS ACCORDANCE WITH THE TYPICAL CONCRETE DETAILS. Carrollton, TX 75006
1. LAYOUT NEW OR TEMPORARY FLOOR OPENINGS, CORES, AND COLUMN BASE PLATE REQUIRED WORKABLE AND CURING TIMES AT THE TIME OF APPLICATION, HILTI FASTENING (972-392-3222 Siddharth Neekhra)
6. USE OF ACCELERATING OR SET-RETARDING ADMIXTURES REQUIRES PRIOR APPROVAL OF
2. STRUCTURAL FRAME CONSISTS OF COLUMNS AND MEMBERS FRAMING INTO COLUMNS, 8. PLACE WATERSTOPS IN ALL EXTERIOR CONSTRUCTION JOINTS BELOW GRADE AND ANCHOR LOCATIONS AS SHOWN ON THE DRAWINGS. SYSTEMS, TULSA, OK
THE ARCHITECT. IN GENERAL, USE OF CALCIUM CHLORIDE WILL NOT BE PERMITTED.
INCLUDING GIRDERS, BEAMS, TRUSSES AND BRACING. ELSEWHERE AS CALLED FOR. CIVIL ENGINEER
2. AFTER PROPOSED OPENINGS, SLEEVES, AND ANCHORS HAVE BEEN LOCATED, ENGAGE 2. DOWELS AND THREADED RODS, OF THE SIZE, TYPE, AND EMBEDMENT SHOWN ON THE
CEMENT SHALL BE TYPE I OR TYPE III (ASTM C 150), EXCEPT AS FOLLOWS: Kimley-Horn and Associates, Inc.
3. THE STRUCTURAL FLOOR AND ROOF FRAMING IS CONSIDERED TO BE "RESTRAINED" IN 9. FLOORS ARE NOT DESIGNED TO SUPPORT FORMWORK AND WET CONCRETE WEIGHT OF TESTING LABORATORY TO LOCATE AND MARK LINES OF REINFORCING ON THE SLAB AT DRAWINGS, SHALL BE INSTALLED BY PERSONNEL TRAINED TO INSTALL ADHESIVE 13455 Noel Road, Two Galleria Office Tower, Suite 700
CLASS OF CEMENT
ACCORDANCE WITH THE U.L. "FIRE RESISTANCE DIRECTORY," FOR PURPOSES OF NEXT LEVEL. CONTRACTOR SHALL DESIGN AND PROVIDE RESHORING TO PREVENT THOSE LOCATIONS. NOTIFY STRUCTURAL ENGINEER AND ARCHITECT TO SITE OBSERVE, ANCHORS AND SHALL BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S Dallas, TX 75240
CONCRETE TYPE
ESTABLISHING THE FIRE RESISTANCE RATING. OVERSTRESSING THE STRUCTURE. UNLESS ALL PROPOSED MODIFICATIONS MEET THE CONDITIONS IN PARAGRAPHS 5 AND 6, PRINTED INSTALLATION INSTRUCTIONS (MPII) AND AS INDICATED ON THE DRAWINGS. A (972-770-1300 Alex Rathbun)
A I/II
BELOW. MODIFY OPENING LOCATIONS IF REQUIRED. MANUFACTURER’S REPRESENTATIVE SHALL BE PRESENT DURING INITIAL INSTALLATION TO
4. STEEL BEAMS WHICH ARE LIGHTER THAN THE MINIMUM SIZE SET FORTH IN THE 7. LIGHTWEIGHT CONCRETE SHALL HAVE A MAXIMUM CURED DENSITY OF 120 POUNDS PER 10. THE HOUSEKEEPING PADS UNDER MECHANICAL EQUIPMENT ARE SHOWN AND SPECIFIED PROVIDE ONSITE TRAINING OF INSTALLERS. LANDSCAPE ARCHITECT
REFERENCED U.L. ASSEMBLY SHALL RECEIVE ADDITIONAL SPRAYED FIREPROOFING AS ON THE MECHANICAL DRAWINGS. REINFORCE HOUSEKEEPING PAD WITH #3@8" ON 3. TO AVOID CUTTING REINFORCING BEYOND THE EDGE OF THE OPENINGS, CORNERS OF SWA Group
CUBIC FOOT.
REQUIRED TO ACHIEVE THE DESIGNATED RATING. CENTER EACH WAY, UNLESS SHOWN OTHERWISE ON MECHANICAL DRAWINGS. SQUARE OR RECTANGULAR OPENINGS MAY NOT BE OVERCUT. WHEN REINFORCING IS 3. WHERE INSTALLATION OF ADHESIVE ANCHORS IS HORIZONTALLY OR UPWARDLY INCLINED 2001 Irving Boulevard, Suite 157
ALLOWED TO BE CUT, IT MAY BE CUT ONLY WITHIN THE LIMITS OF THE NEW OPENINGS. TO SUPPORT SUSTAINED TENSION LOADS, THE INSTALLING PERSONNEL SHALL BE Dallas, TX 75207
CONCRETE REINFORCEMENT 11. THE CONTRACTOR SHALL TAKE PRECAUTIONS TO ENSURE COMPLETE CONSOLIDATION OF
4. CORNERS OF OPENINGS MAY BE CORE DRILLED AND CUT BETWEEN CORES, OR CORES
CERTIFIED IN ACCORDANCE WITH THE ACI/CRSI ADHESIVE ANCHOR INSTALLER
CERTIFICATION PROGRAM, OR EQUIVALENT.
(214-954-0016 Chuck McDaniel)
SPECIAL INSPECTION REQUIREMENTS 1. REINFORCING STEEL SHALL BE NEW OR RECYCLED DOMESTIC DEFORMED BILLET STEEL,
CONCRETE BEHIND ALL POST-TENSIONING ANCHORAGES.
MAY BE CUT ALONG EDGES OF OPENING. CONCRETE MAY THEN BE CHIPPED OUT OF THE STRUCTURAL
CONFORMING TO ASTM A 615 12. GROUT OR CONCRETE CONTAINING CHLORIDES, FLUORIDES, SULFIDES, NITRATES, OR CENTER OF THE OPENING. 4. AT CORED HOLES, WET HOLES, OR HOLES DEEPER THAN 18 INCHES, SUBSTITUTE A SLOW Datum Engineers
1. PERIODIC SITE OBSERVATIONS BY THE ENGINEER OF RECORD ARE SOLELY FOR THE 6516 Forest Park Road
PURPOSE OF DETERMINING GENERAL CONFORMANCE WITH THE CONTRACT A. #3 THROUGH #6 GRADE 60 OTHER SUBSTANCES DETRIMENTAL TO PRESTRESSING STEEL SHALL NOT BE USED. CURE EPOXY ADHESIVE OR OTHER APPROPRIATE PRODUCT RECOMMENDED BY THE
5. DO NOT CORE OR CUT THROUGH BEAMS OR JOISTS. MANUFACTURER FOR THE SPECIAL APPLICATION. Dallas, TX 75235
DOCUMENTS. THOSE LIMITED OBSERVATIONS ARE NOT A SUBSTITUTE FOR INSPECTIONS B. #7 THROUGH #18 GRADE 75 (214-358-0174 Rodolfo D'Arlach)
AND TESTING PERFORMED BY THE OWNER’S QUALIFIED, INDEPENDENT TESTING 2. REINFORCING STEEL SHOWN IN SECTIONS OF BEAMS, WALLS AND COLUMNS IS SCHEMATIC 13. CONSTRUCTION JOINTS IN POST-TENSIONED MEMBERS OTHER THAN WHERE SHOWN
INDICATION THAT REINFORCING EXISTS. SEE SCHEDULES, SECTION NOTES, AND GENERAL SHALL BE APPROVED BY THE ARCHITECT. 6. WHERE THE FOLLOWING CONDITIONS ARE MET, CORING IS STRUCTURALLY ACCEPTABLE 5. ALL POST-INSTALLED ANCHORS SHALL BE INSPECTED BY A SPECIAL INSPECTOR IN
LABORATORY, NOR ARE THEY INTENDED TO IDENTIFY ALL DEFECTS AND DEFICIENCIES IN MEP ENGINEER
NOTES FOR ACTUAL REINFORCING REQUIRED. WITHOUT FURTHER RESERVATION. OTHER RESTRICTIONS MAY APPLY WHICH ARE BEYOND ACCORDANCE WITH THE BUILDING CODE. INSTALLATION OF GROUTED DOWELS AND RODS
THE WORK BY THE CONTRACTOR. THOSE OBSERVATIONS DO NOT FULFILL ANY PART OF ME Engineers, Inc.
14. ALL POCKETS OR BLOCKOUTS REQUIRED FOR ANCHORAGES SHALL BE ADEQUATELY THE SCOPE OF THE STRUCTURAL CRITERIA: SHALL BE CONTINUOUSLY INSPECTED BY THE TESTING LABORATORY, TO ENSURE THAT
THE SPECIAL INSPECTIONS REQUIREMENTS GIVEN IN THE SPECIFICATIONS. THE 1825 Market Center Blvd., Suite 600
DESIGNATED SPECIAL INSPECTOR IS SOLELY RESPONSIBLE FOR FULFILLING THE SPECIAL 3. REFER TO DOWEL SCHEDULE, SHEET 5/S304-OF, FOR ALL BARS MARKED "DWL" ON THE REINFORCED SO AS NOT TO DECREASE THE STRENGTH OF THE STRUCTURE. ALL HOLES ARE OF PROPER DIAMETER AND LENGTH, ARE PROPERLY CLEANED, AND THAT
A. SLAB CORES WITH A MAXIMUM DIAMETER OF 6” THAT ARE LOCATED 1” CLEAR OF ALL Dallas, TX 75207
INSPECTION REQUIREMENTS AS OUTLINED HERE AND DEFINED IN THE SPECIFICATIONS DRAWINGS. POCKETS SHALL BE WATERPROOFED TO ELIMINATE WATER LEAKAGE THROUGH OR INTO DOWELS AND RODS ARE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S (214-741-1589 Drew Shivley)
THE POCKET. EMBEDDED REINFORCING AND ARE ALIGNED WITH AND SPACED AT LEAST 6” CLEAR OF PRINTED INSTALLATION INSTRUCTIONS (MPII).
4. DETAIL REINFORCING BARS AND PROVIDE BAR SUPPORTS AND SPACERS IN ACCORDANCE ADJACENT CORES (PARALLEL OR PERPENDICULAR TO THE SLAB SPAN) AND 12” CLEAR
2. REFER TO THE SPECIFICATIONS FOR CODE MANDATED MATERIALS TESTING AND
OF EXISTING OPENINGS IN BOTH DIRECTIONS. SEE TYPICAL CORING DETAIL.
ELEVATOR CONSULTANT
INSPECTION REQUIREMENTS FOR STRUCTURAL WORK. WITH THE ACI DETAILING MANUAL. 15. IF CONCRETE IS PLACED BY THE PUMP METHOD, SUPPORTS SHALL BE PROVIDED TO 6. ANCHORS SHALL BE INSTALLED PERPENDICULAR TO THE FACE OF THE CONCRETE,
UNLESS OTHERWISE INDICATED ON THE DRAWINGS. Persohn | Hahn Associates, Inc.
SUPPORT THE HOSE. THE HOSE SHALL NOT BE ALLOWED TO RIDE ON THE TENDONS. 8612 Broad Meadow Lane
5. WHERE BAR TYPES FROM THE BAR BENDING DIAGRAM ARE SPECIFIED, PROVIDE BARS CONCRETE SHALL NOT BE DROPPED BY HOSE OR BUCKET DIRECTLY ONTO THE TENDONS. B. WHERE SLAB CORES ARE NOT ALIGNED PARALLEL OR PERPENDICULAR TO SLAB SPAN,
3. ITEMS OF STRUCTURAL CONSTRUCTION WHICH REQUIRE SPECIAL INSPECTION INCLUDE, McKinney, TX 75071
ACCORDINGLY. OTHERWISE, DETAIL BARS IN BEAMS, COLUMNS, SLABS, AND WALLS AS THEY SHALL BE SPACED AT LEAST 6” CLEAR OF OTHER CORES IN BOTH DIRECTIONS 7. THE CONTRACTOR SHALL CREATE A TEMPLATE FOR EACH ANCHOR ROD GROUP PRIOR TO (972-832-4232 Tom Williams)
BUT ARE NOT LIMITED TO, THE FOLLOWING:
FOLLOWS: 16. ALL INSERTS AND SLEEVES SHALL BE CAST-IN-PLACE WHEREVER POSSIBLE. DRILLED AND AND 12” CLEAR OF EXISTING OPENINGS. SEE TYPICAL CORING DETAIL. FABRICATING HOLES IN CONNECTION PLATES. TEMPLATES SHALL BE MADE AFTER
FOUNDATION EXCAVATIONS AND FILL OPERATIONS POWDER-DRIVEN FASTENERS WILL BE PERMITTED ONLY WHEN IT CAN BE SHOWN THAT LOCATING EXISTING REINFORCING STEEL WITH FERROSCAN OR SIMILAR NON- INTERIOR DESIGNER
A. RUN TOP AND BOTTOM BARS CONTINUOUS, WITH SPLICES AND HOOKS AS DESCRIBED THE INSERTS WILL NOT SPALL THE CONCRETE AND ARE LOCATED SO AS TO AVOID THE 7. AFTER SETTING FLOOR DRAINS IN PLACE, FILL ALL VOIDS AROUND DRAINS SOLID WITH DESTRUCTIVE REINFORCING IMAGING DEVICE. POSITION ANCHOR HOLES SO AS NOT TO
INSTALLATION OF DRILLED CONCRETE PIERS AND FOOTINGS Rottet Studio
BELOW. TENDONS AND ANCHORAGES. THE CONTRACTOR SHALL MARK TENDON LOCATIONS ON FLOWABLE HIGH-STRENGTH, NON-SHRINK, GROUT. GROUT TO CONFORM TO ASTM C1107. CONFLICT WITH THE EXISTING REINFORCING. ANCHOR POSITIONS MAY BE ADJUSTED IN 808 Travis Street, Suite 100
PLACEMENT OF STRUCTURAL CONCRETE
PLACEMENT OF CONCRETE REINFORCING B. PROVIDE STANDARD 90 DEGREE HOOK ON TOP BARS AT CANTILEVER ENDS. THE SURFACE OF THE SLAB IF DRILLING OR CORING IS TO BE DONE AFTER CONCRETE IS THE FIELD A MAXIMUM OF 1 1/2" FROM THE DIMENSIONS SHOWN ON THE DETAILS, TO AVOID Houston, TX 77002
C. SPLICE TOP AND INTERMEDIATE BARS AT THE CENTER LINE BETWEEN MEMBER PLACED. 8. WATERPROOF OR SEAL CONCRETE AND GROUT AROUND FLOOR DRAINS SO WATER CONFLICT WITH THE EXISTING REINFORCING STEEL. (713-221-1830 x 6105 Anja Majkic)
PLACEMENT AND STRESSING OF CONCRETE PRESTRESSING TENDONS
SUPPORTS, UNLESS NOTED OTHERWISE. CANNOT SEEP INTO JOINTS OR PENETRATE CONCRETE TO AVOID CORROSION OF ANY
INSTALLATION OF DRILLED-IN CONCRETE OR MASONRY ANCHORS (EXPANSION,
D. SPLICE BOTTOM BARS DIRECTLY OVER MEMBER SUPPORTS, UNLESS NOTED REINFORCING THAT HAS BEEN CUT. 8. SUBMIT DRAWINGS OF TEMPLATES FOR ANCHOR ROD GROUPS SHOWING HOLE
FRICTION, CEMENTED, OR GROUTED ANCHORS)
CONSTRUCTION OF REINFORCED MASONRY
FABRICATION AND ERECTION OF STRUCTURAL STEEL
OTHERWISE.
E. SPLICE VERTICAL BARS IN WALLS ONLY AT FLOOR LINES, UNLESS NOTED OTHERWISE.
POST-TENSIONING REINFORCING FIELD DRILLED EXPANSION BOLTS IN
LOCATIONS PRIOR TO FABRICATION OF CONNECTION PLATES.
WELDING AND BOLTING OF STEEL CONNECTIONS HORIZONTAL BARS SHALL BE SPLICED AS SPECIFIED FOR TOP, BOTTOM, AND 1. POST-TENSIONING STRAND SHALL BE 0.5" OR 0.6" DIAMETER 7 WIRE, LOW RELAXATION 9. HOLES SHALL BE DRILLED WITH A HAMMER DRILL. CORED HOLES ARE NOT PERMITTED.
DIAMETER OF HOLES DRILLED IN THE CONCRETE SHALL BE THE SIZE RECOMMENDED BY
4. ARCHITECTURAL, MECHANICAL, AND ELECTRICAL COMPONENTS REQUIRING SPECIAL
INTERMEDIATE BARS OF BEAMS.
F. CENTER BARS NOTED AS "AT SUPT'S." OVER MEMBER SUPPORTS, AND CENTER BARS
STRAND, WITH A YIELD STRENGTH OF 270 KSI. TENDONS SHALL BE UNBONDED; GREASED
AND SHEATHED IN PLASTIC. CONCRETE THE MANUFACTURER FOR THE RESPECTIVE ANCHOR SIZE.
www.datumengineers.com | Co. Reg. No. F-2819
Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
INSPECTIONS PER SECTION 1705 OF THE IBC HAVE NOT BEEN LISTED HERE. REFER TO NOTED AS "BTWN. SUPT'S." BETWEEN SUPPORTS. Datum Project No. 19166
1. WHERE FIELD DRILLED EXPANSION BOLTS ARE PROPOSED FOR AN APPLICATION OR 10. IMPORTANT: AFTER DRILLING, ALL DUST AND OTHER FOREIGN MATTER SHALL BE BLOWN
ARCH/MEP FOR SPECIAL INSPECTION REQUIREMENTS FOR THESE COMPONENTS. G. PLACE BARS NOTED AS "2ND LAYER" BELOW THE PRIMARY TOP BARS (OR ABOVE THE 2. ALL TEARS IN SHEATHING SHALL BE REPAIRED. LOCATION NOT SHOWN ON THESE DRAWINGS, THE PRODUCT AND ITS INTENDED OUT OF THE HOLE WITH COMPRESSED AIR. DO NOT FLUSH WITH WATER. CLEAN SIDES OF DATE ISSUE TITLE
PRIMARY BOTTOM BARS) AND PROVIDE #11 SPACER BARS PLACED AT INTERVALS
APPLICATION SHALL BE SUBMITTED FOR APPROVAL. HOLE AS RECOMMENDED BY MANUFACTURER. HOLES MUST BE DRY. COMPLY WITH 04/03/2020 SCHEMATIC DESIGN PRESENTATION
OF 4'-0" BETWEEN THE TWO LAYERS OF BARS. 3. SLIGHT DEVIATIONS IN THE SPACING OF THE SLAB TENDONS WILL BE PERMITTED, WHERE 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
H. ALL BAR SPLICES IN BEAMS, SLABS, AND WALLS, OTHER THAN SHEAR WALLS AND REQUIRED, TO AVOID OPENINGS, INSERTS AND DOWELS WHICH ARE SPECIFICALLY LATEST OSHA REQUIREMENTS WHILE CLEANING HOLES.
CONTROLLED BACKFILL BASEMENT WALLS, SHALL BE 30 BAR DIAMETERS, EXCEPT THAT SPLICES IN
HORIZONTAL WALL BARS AND INTERMEDIATE BEAM BARS SHALL BE 66 BAR
LOCATED. WHERE LOCATIONS OF TENDONS INTERFERE WITH EACH OTHER, CONTACT THE
2. EXPANSION BOLTS SHALL BE ONE OF THE FOLLOWING (NO SUBSTITUTIONS):
11. ALL ABANDONED HOLES DRILLED IN THE CONCRETE SHALL BE COMPLETELY FILLED WITH
07/22/2020
08/31/2020
ISSUE FOR 50% DESIGN DEVELOPMENT
STRUCTURAL ENGINEER BEFORE MOVING ANY TENDONS. TENDONS SHALL CLEAR STRONG-BOLT 2, SIMPSON STRONG-TIE CO., PLEASANTON, CA
1. BACKFILL MATERIAL SHALL HAVE A PLASTICITY INDEX BETWEEN 5 AND 15. DIAMETERS. BAR SPLICES IN VERTICAL REINFORCEMENT IN WALLS BELOW GRADE AND OPENINGS BY AT LEAST 6" AND SHALL HAVE A MAXIMUM SKEW OF ONE TO SIX ENDING NO NONSHRINK GROUT. 10/30/2020 ISSUE FOR PERMIT
POWER-STUD+SD1, POWERS FASTENERS, BREWSTER, NY 12/18/2020 90% CONSTRUCTION DOCUMENTS
SHEAR WALLS SHALL BE 66 BAR DIAMETER. CLOSER THAN 1'-0" FROM OPENING EDGE.
2. FILL SHALL BE PLACED IN LIFTS NOT TO EXCEED 8". KWIK BOLT TZ, HILTI FASTENING SYSTEMS, TULSA, OK 12. HOLES IN CONNECTION PLATES SHALL BE NO MORE THAN 1/16" LARGER THAN THE 01/25/2021 100% CONSTRUCTION DOCUMENTS
I. SPLICE VERTICAL BARS IN COLUMNS ONLY AT FLOOR LINES, UNLESS NOTED
OTHERWISE. COLUMN BAR SPLICES SHALL BE 44 BAR DIAMETERS, MINIMUM, UNLESS 4. SHOP DRAWINGS SHALL SHOW SEQUENCE OF PLACING POST-TENSIONING TENDONS AT ANCHOR DIAMETER. IF LARGER DIAMETER HOLES ARE NECESSARY FOR ERECTION
3. FILL SHALL BE COMPACTED AT WORKABLE MOISTURE CONTENTS AT OR ABOVE THE 3. ONLY ONE LENGTH OF BOLT SHALL BE PRESENT ON THE JOBSITE FOR EACH BOLT PURPOSES, THE CONTRACTOR SHALL PROVIDE PLATE WASHERS SUFFICIENTLY WELDED
SCHEDULED OR DETAILED OTHERWISE. COLUMNS (WEAVING OF PERPENDICULAR STRANDS AS REQUIRED TO MAINTAIN PROPER
OPTIMUM MOISTURE CONTENT AND COMPACTED TO ATLEAST 95 PERCENT OF THE DIAMETER, UNLESS OTHERWISE SPECIFIED ON THE DRAWINGS. TO THE CONNECTION PLATE TO TRANSFER THE SPECIFIED LOAD.
J. PLACE A COLUMN TIE 3" ABOVE THE TOP OF THE FOUNDATION OR INTERSECTING SLAB DRAPE). RESERVED FOR REVIEWERS NOTES
MAXIMUM DRY DENSITY OBTAINED BY STANDARD COMPACTION PROCEDURES (ASTM AT ANY LEVEL AND 3" BELOW THE LOWEST HORIZONTAL REINFORCING IN THE SLAB
D-698). 4. EXPANSION BOLTS, OF THE DIAMETER AND EMBEDMENT SHOWN ON THE DRAWINGS,
OF THE FLOOR OR ROOF FRAMING ABOVE AND SPACE TIES AS REQUIRED IN BETWEEN. 5. PLACE TWO CONTINUOUS NO. 4 BARS BEHIND UNIFORMLY SPACED ANCHORS AT EDGE OF SHALL BE INSTALLED BY PERSONNEL TRAINED TO INSTALL EXPANSION BOLTS AND SHALL
4. THE GRANULAR FILL CAN BE USED AS BACKFILL MATERIAL BEHIND RETAINING WALLS AND
WHERE BEAMS FRAME FROM FOUR DIFFERENT DIRECTIONS INTO A COLUMN, TIES
MAY BE TERMINATED WITHIN THE FLOOR FRAMING 3" BELOW THE LOWEST
SLAB. BE INSTALLED IN ACCORDANCE WITH THE CONTRACT DOCUMENTS AND THE ELEVATOR FRAMING
BELOW GRADE WALLS. GRANULAR FILL SHOULD CONSIST OF CRUSHED LIMESTONE WITH MANUFACTURER’S PRINTED INSTALLATION INSTRUCTIONS (MPII). WHERE PROVISIONS OF
HORIZONTAL REINFORCING IN THE SHALLOWEST BEAM. TOP OF COLUMNS 6. UNIFORM SLAB TENDONS SHALL BE STRESSED BEFORE BEAM TENDONS OR BANDED SLAB 1. STRUCTURAL BEAMS SUPPORTING THE ELEVATOR BEAMS ARE SHOWN FOR:
LESS THAN 3% PASSING NO. 200 SIEVE AND LESS THAN 30% PASSING NO. 40 SIEVE. THE THE ABOVE REFERENCED DOCUMENTS ARE IN CONFLICT, THE MOST STRINGENT
SUPPORTING STRUCTURAL STEEL SHALL HAVE 3 TIES AT 3" O.C. STARTING 3" BELOW TENDONS. a. THYSSENKRUPP PASSENGER ELEVATORS 1 & 2: GEARED TRACTION, 3500 LBS. 500
FINE MATIEALS IN THE GRANULAR FILL SHOULD BE NON-PLASTIC. THE GRANULAR FILL REQUIREMENT SHALL GOVERN.
THE TOP OF THE COLUMN. F.P.M.
SHOULD BE COMPACTED TO 95% OF MAXIMUM DRY DENSITY AT OR ABOVE THE OPTIMUM K. PROVIDE CORNER BARS FOR EACH HORIZONTAL BAR AT THE INSIDE AND OUTSIDE 7. MINIMUM CONCRETE COVER OVER TENDONS SHALL BE AS FOLLOWS:
MOISTURE CONTENT AS OBTAINED USING THE STANDARD PROCTOR METHOD (ASTM 5. ALL POST-INSTALLED ANCHORS SHALL BE INSPECTED BY A SPECIAL INSPECTOR IN b. THYSSENKRUPP SERVICE ELEVATOR, GEARED TRACTION, 4500 LBS., 500 F.P.M.
FACES OF INTERSECTING GRADE BEAMS OR WALLS. REFER TO CORNER BAR DETAILS INTERIOR SLAB SPANS: 3/4" IF AN ELEVATOR OF ANOTHER MODEL OR MANUFACTURER IS USED, SUPPORTING
D-698). ACCORDANCE WITH THE BUILDING CODE. INSTALLATION OF EXPANSION BOLTS SHALL BE
ON SHEET 3/S304-OF. SLAB END SPANS AND CANTILEVERS: 1 1/2" BEAMS DESIGN SHALL BE VERIFIED BY THE CONTRACTOR.
CONTINUOUSLY INSPECTED BY THE TESTING LABORATORY, TO ENSURE THAT HOLES ARE
INTERIOR BEAM OR JOIST SPANS: 1 1/2" OF PROPER DIAMETER AND LENGTH, THAT MINIMUM INSTALLATION TORQUES ARE
5. COMPACTION AND MOISTURE CONTENT OF CONTROLLED BACKFILL SHALL BE VERIFIED BY 6. BARS SHOWN IN THE SCHEDULE TO HOOK AT DISCONTINUOUS ENDS SHALL HAVE THE BEAM OR JOIST END SPANS AND CANTILEVERS: 2"
AN INDEPENDENT TESTING LABORATORY. OBTAINED, AND THAT BOLTS ARE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S 2. SLABS AT THE BASE OF ELEVATOR PITS SHALL BE PER DETAIL 6/S304-OF
HOOK PLACED HORIZONTALLY AT EXTERIOR CORNERS.
PRINTED INSTALLATION INSTRUCTIONS (MPII).
8. MINIMUM CONCRETE COVER OVER ANCHORAGE ASSEMBLY SHALL BE 2" AT PERMANENTLY
6. IN THE CASE OF GRANULAR BACKFILL, IT IS RECOMMENDED THAT A 2-FOOT THICKNESS OF 7. PROVIDE FOUNDATION DOWELS TO MATCH MASONRY WALL REINFORCEMENT. DOWELS EXPOSED FACES AND 1 1/2" ELSEWHERE. 6. BOLTS SHALL BE INSTALLED PERPENDICULAR TO THE FACE OF THE CONCRETE. THE REV. DATE ISSUE TITLE
WELL-COMPACTED, IMPERVIOUS CLAY WITH PI GREATER THAN 30 COVER BE PLACED OVER SHALL EXTEND A MINIMUM OF 60 BAR DIAMETERS ABOVE AND 30 BAR DIAMETERS BELOW
MAXIMUM DEVIATION FROM PERPENDICULAR SHALL BE 6 DEGREES. ALL BOLTS INSTALLED .05 12/18/2020 Permit Set Update
THE BACKFILL SURFACE TO REDUCE INFILTRATION IN AREAS THAT ARE NOT COVERED BY TOP OF FOUNDATION. 9. TENDONS SHALL BE INSERTED INTO CONDUIT BEFORE POURING CONCRETE.
PAVEMENT. OUTSIDE OF THE SPECIFIED TOLERANCE SHALL BE CONSIDERED UNACCEPTABLE.
7. BACKFILL SHALL NOT BE PLACED AGAINST FOUNDATION WALLS TALLER THAN 4'-0" UNTIL
8. REFER TO SLAB TEMPERATURE REINFORCING SCHEDULE, SHEET 20E/S402-OF, FOR 10. TENDONS SHALL CLEAR BLOCK-OUTS AND SLEEVES BY AT LEAST 6". WHEN CONFLICTS
7. THE CONTRACTOR SHALL CREATE A TEMPLATE FOR EACH BOLT GROUP PRIOR TO
ROOF MOUNTED MECHANICAL UNITS
TEMPERATURE REINFORCING IN SLABS WHERE NOT SPECIFICALLY DETAILED. OCCUR BETWEEN DETAILED TENDON LOCATION AND SLEEVES, BLOCK-OUTS OR OTHER
ALL SUPPORTING SLABS, BEAMS, STRUTS, ETC., HAVE ATTAINED THEIR 28-DAY DESIGN FABRICATING HOLES IN CONNECTION PLATES. TEMPLATES SHALL BE MADE AFTER 1. ROOF MOUNTED MECHANICAL UNIT LOCATIONS AND DESIGN WEIGHTS ARE SHOWN ON
REINFORCEMENT, CONTACT THE STRUCTURAL ENGINEER BEFORE MOVING ANY TENDONS.
STRENGTH, UNLESS PROPER BRACING IS INSTALLED IN A MANNER APPROVED BY THE 9. CONCRETE COVER FOR REINFORCING STEEL SHALL BE AS FOLLOWS, MEASURED TO LOCATING EXISTING REINFORCING STEEL WITH FERROSCAN OR SIMILAR NON- THE ROOF FRAMING PLANS. CONTRACTOR SHALL NOTIFY THE ENGINEER IF ACTUAL SIZES,
ARCHITECT. NEAREST BAR, STIRRUP OR TIE: DESTRUCTIVE REINFORCING IMAGING DEVICE. POSITION BOLT HOLES SO AS NOT TO WEIGHTS, OR LOCATIONS DIFFER FROM THOSE SHOWN ON THE ROOF FRAMING PLANS.
11. CONCRETE IN THE ANCHORAGE ZONE, DEFINED AS A CYLINDER WITH 12 INCH RADIUS AND
18 INCH LENGTH BEHIND THE ANCHOR SHALL NOT CONTAIN CONDUIT, JUNCTION BOXES, CONFLICT WITH THE EXISTING REINFORCING. BOLT POSITIONS MAY BE ADJUSTED IN THE PROVIDE ADDITIONAL STEEL FRAMING, AS DETAILED, FOR SUPPORT OF RTU CURBS AND
8. WHERE BACKFILL IS REQUIRED ON BOTH SIDES OF A STRUCTURE OR ELEMENT, BACKFILL A. AT SLABS-ON-GRADE, BEAM AND WALL SURFACES DEPOSITED AGAINST THE GROUND SLEEVES OR OTHER VOID-FORMING DEVICES. FIELD A MAXIMUM OF 1 1/2" FROM THE DIMENSIONS SHOWN ON THE DETAILS, TO AVOID PROVIDE DECK SUPPORT ANGLES AT ALL ROOF OPENINGS.
SHALL BE PLACED SIMULTANEOUSLY ALONG BOTH SIDES, SO THAT THE BACKFILL HEIGHT (WITH OR WITHOUT VAPOR RETARDER): 3". CONFLICTS WITH THE EXISTING REINFORCING STEEL.
ON ONE SIDE DOES NOT EXCEED THE HEIGHT ON THE OPPOSITE SIDE BY MORE THAN 4'-0". B. AT FORMED FACES OF BEAMS, COLUMNS AND WALLS EXPOSED TO RAIN OR IN 12. END ANCHORAGE ASSEMBLIES SHALL BE PLACED PERPENDICULAR TO TENDON DRAPE
CONTACT WITH THE GROUND: 2". AND SHALL BE RECESSED TO PROVIDE 1" CLEAR CONCRETE COVER AT ENDS. 8. SUBMIT DRAWINGS OF TEMPLATES SHOWING HOLE LOCATIONS PRIOR TO FABRICATION OF
9. DO NOT PLACE SELECT OR LOW P.I. FILL AGAINST OUTSIDE FACE OF EXTERIOR GRADE C. AT FORMED FACES OF BEAMS NOT EXPOSED TO RAIN OR SOIL: 1 1/2”. CONNECTION PLATES.
BEAM. USE RELATIVELY IMPERVIOUS CLAY AS DESCRIBED ABOVE TO SEAL OUT MOISTURE. D. AT FORMED FACES OF COLUMNS NOT EXPOSED TO RAIN OR SOIL: 1 3/4". 13. AFTER FINAL STRESSING RECORDS HAVE BEEN APPROVED, PUMP GROUT THROUGH
SOILS PLACED ALONG THE EXTERIOR OF GRADE BEAM SHOULD BE ON-SITE CLAY SOILS E. AT INTERIOR AND PROTECTED EXTERIOR FACES OF WALLS: 1". 9. HOLES SHALL BE DRILLED IN A CONTINUOUS OPERATION AVOIDING FREQUENT REMOVAL
CONDUIT, CUT OFF EXCESS STRAND, AND FILL ANCHORAGE RECESS WITH GROUT.
PLACED AND COMPACTED TO AT LEAST 93% OF MAXIMUM DRY DENSITY AT A MINIMUM OF 4 F. AT BEAM AND SLAB BOTTOMS FORMED WITH FIBERBOARD VOID BOXES: 2". OF THE DRILL FROM THE HOLE. AFTER DRILLING, ALL DUST AND OTHER FOREIGN MATTER
PERCENTAGE POINTS ABOVE OPTIMUM MOISTURE CONTENT AS OBTAINED USING THE G. FORMED SURFACES OF SLABS: 14. TENDONS SHALL BE STRESSED IN ONE STAGE OR SHALL BE STRESSED IN STAGES AS SHALL BE BLOWN OUT OF THE HOLE WITH COMPRESSED AIR. COMPLY WITH OSHA
STANDARD PROCTOR METHOD (ASTM D-698). INTERIOR EXPOSURE: 1" NOTED IN THE SCHEDULE. REQUIREMENTS WHILE CLEANING BOLT HOLES.
#5 BAR AND SMALLER, EXPOSED TO WEATHER: 1 1/2"
#6 BAR AND LARGER, EXPOSED TO WEATHER: 2" 15. MINIMUM CONCRETE COVER OVER CONDUIT SHALL BE 2", UNLESS OTHERWISE DETAILED. 10. HOLES DRILLED IN THE CONCRETE SHALL BE SAME NOMINAL DIAMETER AS THE BOLT. USE
H. TOP STEEL IN SLABS AND JOISTS: THE BIT TYPE AND SIZE RECOMMENDED BY THE BOLT MANUFACTURER. HOLES SHALL NOT
INTERIOR EXPOSURE: 1" 16. SHOP DRAWINGS SHALL SHOW SEQUENCE OF STRESSING STRANDS WITHIN A TENDON BE ENLARGED OR REDIRECTED ANYWHERE ALONG THEIR LENGTH.
EXPOSED TO WEATHER: 2" AND TENDONS WITHIN A MEMBER. BEAM SHALL BE STRESSED BEFORE SUPPORTING
I. TOP STEEL IN BEAMS: GIRDERS ARE STRESSED. 11. ALL ABANDONED HOLES DRILLED IN THE CONCRETE SHALL BE COMPLETELY FILLED WITH
INTERIOR EXPOSURE: 1 1/2" EPOXY GROUT.
EXPOSED TO WEATHER: 2" 17. PROVIDE BEARING PLATES AT ALL DEAD END ANCHORS. DO NOT USE SPLAYED WIRES FOR
ANCHORAGE. 12. TIGHTEN NUTS AGAINST SMOOTH WASHERS TO THE MINIMUM TORQUE RECOMMENDED BY
10. MAINTAIN THE SPECIFIED COVER DIMENSION WITHIN A TOLERANCE OF PLUS OR MINUS 3/8" THE MANUFACTURER.
EXCEPT FOR SLABS-ON-GRADE AND SOIL-FORMED MEMBERS, WHERE 5/8" TOLERANCE IS 18. DO NOT STRESS TENDONS UNTIL RESULTS OF TEST CYLINDERS INDICATE THAT A MAPLE TERRACE
PERMITTED. EXTRA COVER WEAKENS THE MEMBER AND REDUCED COVER LEADS TO STRENGTH EQUAL TO 75 PERCENT OF THE DESIGN STRENGTH HAS BEEN ATTAINED. 13. HOLES IN CONNECTION PLATES SHALL BE NO MORE THAN 1/16" LARGER THAN THE BOLT
DIAMETER. IF LARGER DIAMETER HOLES ARE NECESSARY FOR ERECTION PURPOSES THE
3001 MAPLE AVENUE
CORROSION. DALLAS, TEXAS, 75201
CONTRACTOR SHALL PROVIDE PLATE WASHERS SUFFICIENTLY WELDED TO THE
11. REFER TO TYPICAL STEEL CONNECTION DETAIL SHEET (G/S640-OF) FOR ADDITIONAL CONNECTION PLATE TO TRANSFER THE SPECIFIED LOAD. GENERAL NOTES
REINFORCING REQUIRED AT STEEL BEAM CONNECTION EMBED PLATES.
190013
PROJECT NUMBER
FIELD DRILLED THROUGH BOLTS STRUCTURAL STEEL WOOD FRAMING
IN CONCRETE 1. COORDINATION OF THE ROOF STRUCTURE AND THE ARCHITECTURAL SECTIONS AND
ELEVATIONS IS CRITICAL TO PROPER STRUCTURAL STEEL FABRICATION. ELEVATIONS OF
1. UNLESS OTHERWISE INDICATED, WOOD FRAMING SHALL COMPLY WITH SECTION 2308
"CONVENTIONAL LIGHT-FRAME CONSTRUCTION" AND TABLE 2304.9.1 "FASTENING
TOP OF STRUCTURAL STEEL ARE SHOWN ON THE ARCHITECTURAL PLANS AND SECTIONS. SCHEDULE" OF THE INTERNATIONAL BUILDING CODE. THE CONTRACTOR SHALL MAINTAIN
1. FIELD DRILLED THROUGH BOLTS TO BE SET IN HARDENED CONCRETE SHALL CONFORM TO REFER TO THESE SECTIONS AND DETAILS TO SET THE STEEL ELEVATIONS AND TO A COPY FOR REFERENCE AT THE JOBSITE. NAILS SHALL BE COMMON NAILS U.N.O.
THE REQUIREMENTS FOR ANCHOR BOLTS IN THE SPECIFICATIONS. UNDERSTAND THE ARCHITECTURAL INTENT. .016
2. JOISTS RAFTERS SHALL BE NO. 2 SOUTHERN PINE FOR SPANS LESS THAN 8'-6" AND NO. 1
2. ALL POST-INSTALLED ANCHORS SHALL BE INSPECTED BY A SPECIAL INSPECTOR IN 2. TOLERANCE REQUIREMENTS - STRUCTURAL DRAWINGS INDICATE MISCELLANEOUS STEEL SOUTHERN PINE FOR SPANS GREATER THAN 8'6" AT THE HIGH PLATFORM WOOD FRAMING DEVELOPER
ACCORDANCE WITH THE BUILDING CODE. INSTALLATION OF THROUGH BOLTS SHALL BE ELEMENTS SUCH AS SHELF ANGLES, LINTELS, SUPPORT MEMBERS FOR CURTAIN WALLS ON TERRACE. Hines
CONTINUOUSLY INSPECTED BY THE TESTING LABORATORY TO ENSURE THAT HOLES ARE 2200 Ross Avenue, Suite 4200W
OR MASONRY, AND EDGE ANGLES FOR OPENINGS AND PERIMETER CONDITIONS WHICH Dallas, TX 75201
OF PROPER DIAMETER AND LENGTH, ARE PROPERLY CLEANED, AND THAT BOLTS AND ARE INTENDED TO SUPPORT OR BE COORDINATED WITH MATERIALS FURNISHED BY OTHER 3. PROVIDE SOLID BLOCKING OR A BAND BOARD AT ALL FLOOR JOIST BEARING LOCATIONS (972-716-2908 Corbin Eckel)
EPOXY ARE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S PRINTED TRADES. IT IS THE INTENT OF THESE DRAWINGS THAT THESE ELEMENTS BE FIELD OVER WALLS, BEAMS, STRINGERS OR HEADERS. BLOCKING SHALL BE SAME DEPTH AS
INSTALLATION INSTRUCTIONS (MPII). ATTACHED BY FIELD WELDING OR BOLTING TO MEET THE TOLERANCES REQUIRED BY JOIST. LAP OPPOSING JOISTS 3" MINIMUM OVER SUPPORTS. 2800 Post Oak Blvd., 49th Floor
OTHER TRADES, WHICH MAY BE MORE STRINGENT THAN A.I.S.C. TOLERANCES FOR Houston, TX 77056
3. THROUGH BOLTS SHALL BE INSTALLED PERPENDICULAR TO THE FACE OF CONCRETE, STRUCTURAL STEEL. CONTRACTOR SHALL COORDINATE TRADES AND FIELD INSTALL 4. UNLESS OTHERWISE DETAILED, FOR FLOOR OR ROOF JOIST CONNECTIONS TO (713-621-8000 Juan Delgado)
UNLESS OTHERWISE INDICATED ON THE DRAWINGS. MISCELLANEOUS STEEL ELEMENTS AND THE STRUCTURAL STEEL FRAME TO COMPLY WITH SUPPORTING BEAMS (FLUSH TYPE CONNECTIONS), USE TYPE "LU" JOIST HANGERS, AS
THE TOLERANCE CRITERIA FOR PROPER INSTALLATION OF MATERIALS BY OTHER TRADES. MANUFACTURED BY THE SIMPSON COMPANY OR "TECO-U-GRIP" JOIST HANGERS, AS EQUITY PARTNERS
4. THE CONTRACTOR SHALL CREATE A TEMPLATE FOR EACH ANCHOR ROD GROUP PRIOR TO MANUFACTURED BY THE TIMBER ENGINEERING COMPANY. SLOPING ROOF JOISTS McNair Interests
FABRICATING HOLES IN CONNECTION PLATES. TEMPLATES SHALL BE MADE AFTER 3. STRUCTURAL STEEL MATERIAL SHALL CONFORM TO THE FOLLOWING DESIGNATIONS: HANGERS SHALL BE TYPE "LSU," AS MANUFACTURED BY THE SIMPSON COMPANY, OR 109 N. Post Oak Lane, Suite 600
LOCATING EXISTING REINFORCING STEEL WITH FERROSCAN OR SIMILAR NON- EQUAL. THE TYPE OF HANGER USED SHALL BE AS RECOMMENDED BY THE Houston, TX 77024
DESTRUCTIVE REINFORCING IMAGING DEVICE. POSITION ANCHOR HOLES SO AS NOT TO WIDE FLANGE (W) SHAPES AND TEES A 992 (50 KSI YIELD) MANUFACTURER FOR THE SIZE OF JOIST SUPPORTED. (Drew Steffen)
CONFLICT WITH THE EXISTING REINFORCING. ANCHOR POSITIONS MAY BE ADJUSTED IN OTHER ROLLED SHAPES, PLATES AND RODS A 36 (36 KSI YIELD)
THE FIELD A MAXIMUM OF 1 1/2" FROM THE DIMENSIONS SHOWN ON THE DETAILS, UNLESS Mitsui Fudosan America
HOLLOW STRUCTURAL SHAPES (HSS OR TS) A 500, GRADE B OR GRADE C (42 KSI YIELD 5. ALL EXPOSED WOOD FRAMING SHALL RECEIVE A PRESERVATIVE TREATMENT. SEE 1251 Avenue of the Americas, Suite 800
NOTED OTHERWISE, TO AVOID CONFLICT WITH THE EXISTING REINFORCING STEEL. NOTIFY ROUND/46 KSI YIELD SQUARE) ARCHITECTURAL SPECIFICATIONS. New York, New York 10020
ENGINEER OF RECORD IF SUITABLE CONFIGURATION THAT DOES NOT CONFLICT WITH PIPE A 53, GRADE B (35 KSI YIELD) (David Leff)
EXSITING REINFORCING CANNOT BE OBTAINED. BOLTS FOR CONNECTIONS A 325N 6. THE FLOOR SHEATHING SHALL BE PRE-DRILLED TO THE WOOD FRAMING MEMBERS.
ANCHOR BOLTS (ANCHOR RODS) F 1554 (36 KSI YIELD) PROVIDE 2 SCREWS EACH END AND 1 SCREW AT INTERMEDIATE SUPPORTS. OFFICE/RETAIL ARCHITECT
5. SUBMIT DRAWINGS OF TEMPLATES FOR ANCHOR ROD GROUPS SHOWING HOLE
5G Studio Collaborative, LLC.
LOCATIONS PRIOR TO FABRICATION OF CONNECTION PLATES. 4. PREDESIGNED BEAM CONNECTION DETAILS ARE SHOWN ON SHEET S501-OF. OTHER 7. ALL BOLTS AND LAG SCREWS SHALL HAVE STANDARD WASHERS. ALL ANCHOR AND 1217 Main St., Suite 500
TYPICAL CONNECTIONS ARE SHOWN IN TYPICAL DETAILS. CONNECTIONS WHICH ARE NOT EXPANSION BOLTS USED FOR WOOD TO CONCRETE/MASONRY CONNECTIONS IN EXTERIOR Dallas, TX 75202
6. HOLES SHALL BE DRILLED WITH A HAMMER DRILL. CORED HOLES ARE NOT PERMITTED. SPECIFICALLY DETAILED SHALL BE DESIGNED BY THE FABRICATOR IN ACCORDANCE WITH LOCATIONS SHALL BE HOT DIP GALVANIZED OR STAINLESS STEEL. (214-347-4982 Christine Robbins-Elrod)
DIAMETER OF HOLES DRILLED IN THE CONCRETE SHALL BE 1/4" LARGER THAN THE THE CONNECTION NOTES AND SPECIFICATIONS.
ANCHOR DIAMETER. 8. REFER TO THE ARCHITECTURAL DRAWINGS FOR ADDITIONAL WOOD FRAMING MEMBERS MASTER/MULTIFAMILY ARCHITECT
5. ALL MOMENT CONNECTIONS SHALL BE FULL WELDED CONNECTIONS DESIGNED TO AND PROVIDE SUCH MEMBERS EVEN THOUGH NOT SHOWN ON THE STRUCTURAL GFF Architects
7. IMPORTANT: AFTER DRILLING, HOLES SHALL BE CLEANED WITH A NYLON BRUSH FOR A DEVELOP THE FULL CROSS-SECTION OF THE MEMBER. STIFFENER PLATES, WHERE DRAWINGS. 2808 Fairmount St., Suite 300
MINIMUM OF 4 CYCLES AND ALL DUST AND OTHER FOREIGN MATTER SHALL BE BLOWN OUT SHOWN, ARE MANDATORY AND MAY NOT BE OMITTED. MOMENT CONNECTIONS ARE Dallas, TX 75201
OF THE HOLE WITH OIL-FREE COMPRESSED AIR. DO NOT FLUSH WITH WATER. HOLES INDICATED ON THE PLANS BY A TRIANGULAR BULB ON THE END OF THE BEAM, OR BY THE 9. CONNECTION HARDWARE: ALL METAL CONNECTORS AND STRAPS SHALL BE FURNISHED (214-303-1500 Michael Reyes)
MUST BE DRY. LETTERS "MC". WITH GALVANIZED FINISH. ALL CONNECTION ASSEMBLIES FABRICATED FROM STEEL
STRUCTURAL SHAPES AND PLATES SHALL BE HOT-DIP GALVANIZED AFTER FABRICATION. ZONING/ENTITLEMENT
8. BOLTS SHALL BE SET ON 1/8” SHIM ON EACH END TO PREVENT BOLT FROM RESTING 6. CANTILEVER BEAMS MOMENT CONNECTED TO THE FRAME SHALL BE THE SAME SIZE AS FASTENERS USED IN EXTERIOR LOCATIONS SHALL BE GALVANIZED. Baldwin Associates
DIRECTLY ON CONCRETE. THE BACK-UP SPAN IF NO SIZE IS GIVEN. 3904 Elm Street, Suite B
Dallas, TX 75226
9. INSERT A CLEAR PLASTIC TUBE ON THE BOTTOM OF THE HOLE ON THE INLET SIDE FOR (214-824-7949 Robert Baldwin)
7. ALL BOLTS SHALL BE TIGHTENED TO A "SNUG TIGHT" CONDITION.
INJECTING EPOXY AND ANOTHER TUBE AT THE TOP OF THE HOLE AT THE EXIT SIDE WHICH
IS TAPED SO THAT TOP OF TUBE IS ABOVE HOLE BY A MINIMUM OF 2 INCHES IN ORDER TO 8. BACK TO BACK CHANNELS OR DOUBLE ANGLES ACTING AS COMPRESSION MEMBERS
SLABS ON STEEL FORM DECKING GEOTECH
ALLOW AIR TO ESCAPE SHALL BE CONNECTED TO EACH OTHER AT THIRD POINTS ALONG THE LENGTH BY ECS Southwest, LLP
1. SLABS FORMED ON CORRUGATED STEEL FORM DECKING SHALL BE 4” THICK (TOTAL) 3033 Kellyway Drive, Suite 110
WELDING IN SPACER PLATES OF EQUAL THICKNESS TO THE GUSSET PLATES. UNEQUAL AND SHALL BE REINFORCED WITH 6X6-W4.0X4W.0 WELDED WIRE MESH OR #3@12” EACH
10. EACH END SHALL BE SEALED WITH SIKADUR 31 HI-MOD GEL BY SIKA, OR EQUIVALENT. Carrollton, TX 75006
LEG ANGLES SHALL BE ORIENTED LONG LEG DOWN UNLESS NOTED OTHERWISE. WAY AT MID-DEPTH OF SLAB. (972-392-3222 Siddharth Neekhra)
11. INJECT HOLE WITH SIKADUR 35 HI-MOD LVL BY SIKA, SIKADUR CRACK FIX BY SIKA, OR 9. TEMPORARY CONSTRUCTION BRACING OF STRUCTURAL STEEL FRAME SHALL REMAIN IN 2. STEEL FORM DECK SHALL BE MANUFACTURED FROM SHEET STEEL CONFORMING TO CIVIL ENGINEER
EQUIVALENT, AS PER MPII AND CONTINUE UNTIL EXPOXY BEGINS TO ESCAPE FROM TUBE PLACE UNTIL AFTER ALL PERMANENT BRACING COMPONENTS HAVE BEEN COMPLETED. ASTM A 653 GRADE 60 OR BETTER, HAVING A MINIMUM YIELD STRENGTH OF 60,000 PSI. Kimley-Horn and Associates, Inc.
AT EXIT SIDE WITH NO AIR BUBBLES, THEN SEAL OFF OPENINGS. THE LATERAL-LOAD-RESISTING SYSTEM OF THE BUILDING INCLUDES MOMENT-CONNECTED DECK SHALL BE GALVANIZED WITH G60 COATING THICKNESS. DECK PROPERTIES SHALL 13455 Noel Road, Two Galleria Office Tower, Suite 700
RIGID FRAMES, DESIGNATED WIND BRACES, CONCRETE SHEAR WALLS, REINFORCED BE EQUAL TO NUCOR/VULCRAFT "CONFORM 1.5C18”, 18 GAUGE X 1.5” DEEP Dallas, TX 75240
12. ALL ABANDONED HOLES DRILLED IN THE CONCRETE SHALL BE COMPLETELY FILLED WITH MASONRY SHEAR WALLS, AND CONNECTING DIAPHRAGM ELEMENTS. THE METAL ROOF (972-770-1300 Alex Rathbun)
NONSHRINK GROUT. DECK AND COMPLETED CONCRETE FILL ON METAL FLOOR DECK ARE ESSENTIAL 3. PLACE DECKING CORRUGATIONS PERPENDICULAR TO SUPPORTS, PROVIDING AT LEAST
DIAPHRAGM COMPONENTS OF THE PERMANENT BRACING SYSTEM. 1 1/2" BEARING ON EACH SUPPORT. DECKING SHALL RUN CONTINUOUS OVER TWO OR LANDSCAPE ARCHITECT
13. HOLES IN CONNECTION PLATES SHALL BE NO MORE THAN 1/16" LARGER THAN THE
MORE SPANS. SINGLE SPANS REQUIRE SHORING. SWA Group
ANCHOR DIAMETER, UNLESS OTHERWISE SHOWN. IF LARGER DIAMETER HOLES ARE 10. WIND BRACES IN THE VERTICAL PLANE ARE DENOTED BY "WB" ON THE PLAN. SEE WIND 2001 Irving Boulevard, Suite 157
NECESSARY FOR ERECTION PURPOSES, THE CONTRACTOR SHALL PROVIDE PLATE BRACE DETAILS FOR CONFIGURATIONS. Dallas, TX 75207
4. DECK CONNECTIONS TO SUPPORTING STEEL SHALL BE PUDDLE WELDS AT 1'-0" ON
WASHERS SUFFICIENTLY WELDED TO THE CONNECTION PLATE TO TRANSFER THE (214-954-0016 Chuck McDaniel)
CENTER, AT ALL SUPPORTS. PUDDLE WELDS SHALL BE FULL-FUSION, 5/8" DIAMETER
SPECIFIED LOAD. 11. STEEL ANGLES AND OTHER SHAPES THAT DEFINE THE EDGE OF THE FLOOR OR ROOF AND WELDS. USE WELD WASHERS ON 24 GAUGE AND THINNER MATERIAL.
ARE SHOWN TO BE WELDED TO SUPPORTING BEAMS, SHALL BE FIELD WELDED, NOT SHOP STRUCTURAL
WELDED, SO THAT THEIR POSITION CAN BE ADJUSTED TO CORRECT FOR FABRICATION 5. PROVIDE AT LEAST 2" OF END LAPS AT SPLICES, ALIGNING THEM OVER SUPPORT LINES. Datum Engineers
AND ERECTION TOLERANCES OF THOSE SUPPORTING BEAMS AND PROVIDE AN EDGE THAT LAP SIDES OF DECK AT LEAST ONE CORRUGATION. SPLICES DO NOT NEED TO BE 6516 Forest Park Road
IS CONSISTENT WITH THE REQUIREMENTS OF THE FINISHES THAT IT SUPPORTS AND/OR STAGGERED. SIDE LAPS SHALL BE FASTENED PER STEEL DECK INSTITUTE Dallas, TX 75235
STRUCTURAL MASONRY ACCOMMODATES. RECOMMENDATIONS WITH #10 SELF DRILLING SCREWS, CRIMP OR BUTTON PUNCH, 5/8”
ARC PUDDLE WELDS, OR 1” LONG FILLET WELDS AT 36” MAX.
(214-358-0174 Rodolfo D'Arlach)
12. SHELF ANGLES SHOWN AS CONTINUOUS IN THE SECTIONS SHALL BE INSTALLED IN 20'-0" MEP ENGINEER
1. MASONRY DESIGN IS BASED ON A MASONRY PRISM STRENGTH OF F'M = 1900 PSI.
MAXIMUM LENGTHS, LEAVING A 1/4" GAP BETWEEN ENDS AND AT CORNERS. LOCATE GAPS 6. FURNISH MESH REINFORCING IN FLAT SHEETS TO OBTAIN PROPER CONCRETE COVER. ME Engineers, Inc.
TO MATCH MASONRY CONTROL JOINTS. AT BUILDING EXPANSION JOINT, LEAVE A GAP TO 1825 Market Center Blvd., Suite 600
2. HOLLOW MASONRY UNITS SHALL CONFORM TO ASTM C 90, LIGHTWEIGHT, GRADE N, Dallas, TX 75207
MATCH EXPANSION JOINT WIDTH.
WITH A MINIMUM UNIT COMPRESSIVE STRENGTH OF 1900 PSI (214-741-1589 Drew Shivley)
13. CONNECT MISCELLANEOUS STEEL MEMBERS USING FILLET WELDS SUFFICIENT TO
3. MORTAR SHALL CONFORM TO ASTM C 270, TYPE S, CONSISTING OF 1 PART PORTLAND
CEMENT, 1/2 PART HYDRATED LIME AND 3 1/2 TO 4 1/2 PARTS MASON’S SAND. DO NOT USE
DEVELOP THE TENSILE STRENGTH OF THE SMALLER MEMBER AT THE JOINT UNLESS CONCRETE FOOTINGS ELEVATOR CONSULTANT
SHOWN OTHERWISE. Persohn | Hahn Associates, Inc.
AIR ENTRAINING LIME, MASONRY CEMENT OR ADMIXTURES. 8612 Broad Meadow Lane
1. THE SPREAD FOOTINGS ARE DESIGNED FOR AN ALLOWABLE NET SOIL PRESSURE OF
14. ALL STEEL SHALL BE FURNISHED WITH SHOP COAT OF RUST INHIBITIVE PRIMER. McKinney, TX 75071
4. COARSE GROUT SHALL CONFORM TO ASTM C 476, WITH A MAXIMUM AGGREGATE SIZE OF 2500 PSF. (972-832-4232 Tom Williams)
3/8". PROPORTIONS BY VOLUME SHALL BE 1 PART PORTLAND CEMENT, 2 1/4 TO 3 PARTS
15. WHERE ANGLES ARE NOTED TO BE CONTINUOUS, PROVIDE FULL BUTT WELD AT SPLICES. 2. THE FOOTING EXCAVATIONS SHALL BE MADE TO NEAT LINES AND SHALL BE FREE OF
MASON’S SAND AND 1 TO 2 PARTS PEA GRAVEL. SLUMP SHALL BE 10" TO 11". INTERIOR DESIGNER
LOOSE OR WET MATERIALS. CONCRETE SHALL BE PLACED DIRECTLY AGAINST THE SOIL
Rottet Studio
5. FOR VERTICAL REINFORCING SEE DETAILS. THE FIRST CELL AT CORNERS AND ENDS OF WITHOUT FORMING IF APPROVED BY THE SOIL ENGINEER. 808 Travis Street, Suite 100
WALLS SHALL BE REINFORCED WITH 2#5 AND GROUTED. 1#4 (EXTENDING 2'-0" BEYOND
CORNERS) SHALL BE PLACED EACH SIDE OF WALL OPENINGS.
METAL ROOF DECK 3. ALL FOOTINGS SHALL BE INSPECTED BY THE SOIL ENGINEER, PRIOR TO PLACING
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
1. ROOF DECK SHALL BE 1 1/2" DEEP, 20 GAUGE, WIDE RIB, GALVANIZED METAL DECK, WITH 6" CONCRETE, IN ORDER TO ASSURE THAT THE BEARING SURFACES ARE CONSISTENT WITH
6. PROVIDE FOUNDATION DOWELS TO MATCH MASONRY WALL REINFORCEMENT. DOWELS RIB SPACING, MEETING THE REQUIREMENTS OF THE STEEL DECK INSTITUTE. DESIGN RECOMMENDATIONS.
SHALL EXTEND A MINIMUM OF 60 BAR DIAMETERS ABOVE AND 30 BAR DIAMETERS BELOW
TOP OF FOUNDATION. 2. ROOF DECK SHALL BE CONTINUOUS OVER THREE OR MORE SPANS. 4. WHERE SOFT AREAS ARE ENCOUNTERED, THE AREA SHALL BE UNDERCUT AS REQUIRED
AND REPLACED WITH CONCRETE.
7. VERTICAL BARS SHALL BE HELD IN POSITION IN THE CENTER OF THE CELL OR GROUT 3. TYPICAL DECK CONNECTIONS SHALL BE AS FOLLOWS: www.datumengineers.com | Co. Reg. No. F-2819
SPACE DURING PLACEMENT OF EACH LIFT OF GROUT UNLESS ANOTHER POSITION IS 5. UTILITY TRENCHES AND OTHER EXCAVATIONS IN THE VICINITY OF STRUCTURAL Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
DETAILED. AT EACH SUPPORT: PUDDLE WELDS AT EACH SIDE LAP AND AT INTERMEDIATE RIBS AT FOOTINGS SHALL NOT BE PERMITTED TO EXTEND DEEPER THAN THE BOTTOM OF ANY
Datum Project No. 19166
AN AVERAGE SPACING OF 12" ON CENTER, NOT TO EXCEED 18" ON CENTER. ADJACENT FOOTING. IF DEEPER EXCAVATION IS REQUIRED VERIFY MINIMUM RELATED
DATE ISSUE TITLE
8. WHEN A FOUNDATION DOWEL DOES NOT LINE UP WITH A VERTICAL CORE IT SHALL BE CLEARANCE REQUIREMENTS WITH THE GEOTECHNICAL ENGINEER. FOOTINGS SHALL
SLOPED NOT MORE THAN ONE HORIZONTAL TO SIX VERTICAL. THE DOWEL SHALL BE AT SIDE LAPS: SCREWS EQUALLY SPACED BETWEEN SUPPORTS, NOT TO EXCEED 36" NOT BE DEEPENED WITHOUT SUCH WRITTEN DIRECTION FROM THE ARCHITECT. 04/03/2020 SCHEMATIC DESIGN PRESENTATION
05/06/2020 ISSUE FOR SCHEMATIC DESIGN
GROUTED INTO A CELL IN VERTICAL ALIGNMENT, EVEN THOUGH IT IS IN AN ADJACENT CELL ON CENTER.
07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
TO THE VERTICAL WALL REINFORCING.
AT EXTERIOR SIDES, PARALLEL TO DECK SPAN: PUDDLE WELDS AT 12" ON CENTER.
10/30/2020 ISSUE FOR PERMIT
9. HORIZONTAL REINFORCING BARS SHALL BE PLACED IN CONTINUOUS MASONRY COURSES,
CONSISTING OF BOND BEAM OR TROUGH BLOCK UNITS, AND SHALL BE SOLIDLY GROUTED 4. SCREWS SHALL BE "TEKS" #12-14X3/4" HWH #2. 12/18/2020 90% CONSTRUCTION DOCUMENTS
01/25/2021 100% CONSTRUCTION DOCUMENTS
IN PLACE.
5. PUDDLE WELDS SHALL BE FULL-FUSION, 5/8" DIAMETER (MINIMUM) WELDS, MADE THROUGH
10. REINFORCING BARS SHALL BE STRAIGHT EXCEPT FOR BENDS AROUND CORNERS AND WELD WASHERS. METAL AROUND WELDS SHALL BE COMPLETELY INTACT AFTER WELDING.
WHERE BENDS OR HOOKS ARE DETAILED ON THE PLANS. RESERVED FOR REVIEWERS NOTES
6. THE METAL ROOF DECK ON THIS PROJECT IS REQUIRED TO PERFORM AS A STRUCTURAL
11. HORIZONTAL REINFORCING STEEL SHALL BE LAPPED WHERE SPLICED AND SHALL BE DIAPHRAGM. ALL WELDS AND SCREWS ARE CRITICAL TO THE SUCCESSFUL PERFORMANCE
WIRED TOGETHER. BEND BARS AT CORNERS AND TEE INTERSECTIONS, PROVIDING OF THE DIAPHRAGM.
STANDARD LAP SPLICES WITH INTERSECTING BARS.
7. SUSPENDED CEILING, LIGHT FIXTURES, DUCTS OR OTHER UTILITIES SHALL NOT BE
12. STANDARD LAP SPLICE LENGTHS FOR REINFORCING BARS SHALL BE AS FOLLOWS: SUPPORTED BY THE STEEL DECK.
40 BAR DIAMETERS FOR #5 BARS AND SMALLER
56 BAR DIAMETERS FOR #6 AND #7 BARS
60 BAR DIAMETERS FOR #8 AND #9 BARS
13. HORIZONTAL WALL JOINT REINFORCING SHALL BE STANDARD TRUSS TYPE AS

MANUFACTURED BY HOHMANN & BARNARD OR WIRE-BOND AT 16" ON CENTER, REV. DATE ISSUE TITLE
VERTICALLY, TYPICAL UNLESS NOTED OTHERWISE. PROVIDE THREE WIRE TRUSS TYPE AS .05 12/18/2020 Permit Set Update
MANUFACTURED BY HOHMAN & BARNARD OR WIRE-BOND WHERE BRICK IS BACKED UP BY .016 05/03/2021 ADDENDUM 08
6", 8", 10", OR 12" CONCRETE MASONRY UNITS.
14. STANDARD WIRE REINFORCEMENT SHALL BE LAPPED AT LEAST 11" AT SPLICES AND SHALL
CONTAIN AT LEAST ONE CROSS WIRE OF EACH PIECE OF REINFORCEMENT IN THE LAPPED
DISTANCE. EXTRA HEAVY DUTY WIRE REINFORCEMENT SHALL BE LAPPED 14" AT SPLICES
AND CROSSWIRES WITHIN THE SPLICE SHALL BE CUT WHERE NECESSARY TO ALLOW SIDE
RODS TO LAP SIDE BY SIDE IN THE MORTAR JOINT.
15. VERTICAL REINFORCING BARS MAY BE SPLICED IN 6'-0" TO 8'-0" (+) LENGTHS, PROVIDED
THE SPLICES IN ADJACENT BARS ARE STAGGERED AND ARRANGED SO THAT NOT MORE
THAN ONE-HALF OF THE TOTAL NUMBER OF BARS ARE SPLICED AT ANY ONE HEIGHT.
16. Z-TIES SHALL BE MANUFACTURED FROM 3/16" DIAMETER COLD DRAWN WIRE,
CONFORMING TO ASTM A 82 OR APPROVED EQUAL. TIES SHALL HAVE A 2" PERPENDICULAR
LEG AT EACH END. TIES SHALL BE GALVANIZED.
17. Z-TIES SHALL BE LOCATED IN ALL HORIZONTAL AND VERTICAL BRICK SURFACES WHICH
ARE USED AS A FORM FOR GROUT. Z-TIES SHALL BE PLACED 1'-4" ON CENTER, EACH WAY
IN VERTICAL BRICK SURFACES, EXCEPT WHERE HORIZONTAL JOINT REINFORCEMENT IS
DETAILED. Z-TIES SHALL BE PLACED AT 8" ON CENTER, EACH WAY IN HORIZONTAL BRICK
SURFACES USED AS BOTTOM FORM AND SHALL BE HOOKED AROUND 1/4" DIAMETER
GALVANIZED RODS LOCATED IN THE HOLES THROUGH THE BRICKS. ONE LEG SHALL BE
PLACED IN MORTAR JOINT A DISTANCE 3/4" FROM AND PARALLEL TO THE OUTSIDE OF THE
BRICK. Z-TIES SHALL BE 6" LONG.
18. PROVIDE 3/8" THROUGH-WALL CONTROL JOINTS AT 40'-0" MAXIMUM SPACING OR AT

LOCATIONS DETAILED ON THE ARCHITECTURAL DRAWINGS. DO NOT LOCATE CONTROL
JOINTS WITHIN WALL OPENINGS OR LINTEL SUPPORTS. COORDINATE SPACING TO MISS MAPLE TERRACE
BEAM AND JOIST BEARING POINTS. CUT ALL REINFORCING AT CONTROL JOINTS, UNLESS 3001 MAPLE AVENUE
NOTED OTHERWISE. DALLAS, TEXAS, 75201
GENERAL NOTES
190013
PROJECT NUMBER
DEVELOPER
Hines
2200 Ross Avenue, Suite 4200W
Dallas, TX 75201
(972-716-2908 Corbin Eckel)
2800 Post Oak Blvd., 49th Floor

Houston, TX 77056
(713-621-8000 Juan Delgado)
1
S220-OF EQUITY PARTNERS
McNair Interests
109 N. Post Oak Lane, Suite 600
Houston, TX 77024
E1 E2 (Drew Steffen)
Mitsui Fudosan America

1251 Avenue of the Americas, Suite 800
New York, New York 10020
(David Leff)
OFFICE/RETAIL ARCHITECT
Dallas, TX 75202
(214-347-4982 Christine Robbins-Elrod)
MASTER/MULTIFAMILY ARCHITECT
GFF Architects
2808 Fairmount St., Suite 300
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
Dallas, TX 75226
(214-824-7949 Robert Baldwin)
GEOTECH
ECS Southwest, LLP
Carrollton, TX 75006
(972-392-3222 Siddharth Neekhra)
CIVIL ENGINEER
RETENTION SYSTEM Kimley-Horn and Associates, Inc.
FOR OFFICE BUILDING 10'-9 1/4" T.O.S.C. EL. = 445'-10" 13455 Noel Road, Two Galleria Office Tower, Suite 700
C10, P3
Dallas, TX 75240
E/S302-OF 3'-4" C7, P5 (972-770-1300 Alex Rathbun)
2 1 2
E/S302-OF OUTLINE OF BUILDING ABOVE
S305-OF S305-OF S305-OF
1 DROP IN BOTTOM OF LANDSCAPE ARCHITECT
S305-OF BASEMENT WALL SWA Group
E-C 2001 Irving Boulevard, Suite 157
6'-4"
Dallas, TX 75207
7'-1"
C10 , P3 7'-10"
1'-7"
9"
E/S302-OF
1'-3" T.O.S.C. EL. = 445'-10"
A 6 1 STRUCTURAL
P/S302-OF TYP. @
9"
9 ELEV. SE1 Datum Engineers
S304-OF S222-OF
BASEMENT WALL
8'-2"
S502-OF ELEV. PE2 6516 Forest Park Road
PILASTER 4 3 2 M/S302-OF Dallas, TX 75235
TYP. (214-358-0174 Rodolfo D'Arlach)
19'-3"
17'-9"
S222-OF S222-OF 7 S305-OF OUTLINE OF
SIM.
SW-1
20F/S303-OF BASEMENT
STAIR 1 S304-OF
TEMPORARY
MEP ENGINEER
15 ELEV. WALL ABOVE ME Engineers, Inc.
A8 1
4
T.O.S.C. EL. = 452'-4" S305-OF
PE1 6 RETENTION SYSTEM
1825 Market Center Blvd., Suite 600
S502-OF
Dallas, TX 75207
9"
S305-OF S304-OF
(214-741-1589 Drew Shivley)
B 1 C6, P5
5"
1'-6"
9"
S305-OF E/S302-OF OUTLINE OF ELEVATOR CONSULTANT

SIM.
2 SW-2 8 6
STAIR TO NEW Persohn | Hahn Associates, Inc.
6 7 S502-OF S304-OF 8612 Broad Meadow Lane
S221-OF NOTE: RESIDENTIAL
S502-OF S502-OF McKinney, TX 75071
3 2 DROP IN BOTTOM PENETRATION FOR THIS TOWER GARAGE
16 (972-832-4232 Tom Williams)
P4, TYP. AT S502-OF S222-OF OF BASEMENT WALL PIER TO START AT BOTTOM
7'-1 1/4" SHEARWALLS
S305-OF
OF SUMP EXCAVATION.
30'-7 1/4"
INTERIOR DESIGNER
Rottet Studio
B.5 RETENTION SYSTEM 808 Travis Street, Suite 100
FOR OFFICE BUILDING Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
P1, CC/S302-OF
14'-6"
SLAB-ON GRADE
1
SEE S303-OF .016
C3, P3 OUTLINE OF BUILDING ABOVE
S305-OF E/S302-OF
OUTLINE OF BUILDING ABOVE
C www.datumengineers.com | Co. Reg. No. F-2819
Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
1" E.J. Datum Project No. 19166
3'-9 1/2" F DATE ISSUE TITLE

1 12 S302-OF 04/03/2020 SCHEMATIC DESIGN PRESENTATION
S223-OF S305-OF 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SEE GARAGE DRAWINGS FOR 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
OUTLINE OF CONTINUATION OF RETENTION TEMPORARY SEE GARAGE DRAWINGS FOR 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
RESIDENTIAL SYSTEM AND FOR FOOTING RETENTION SYSTEM 154'-6" (F.V.) RETENTION SYSTEM AND SEE GARAGE DRAWINGS FOR
TOWER GARAGE UNDERPINNING GARAGE WALLS CONTINUATION OF RETENTION
SEE GARAGE RESIDENTIAL TOWER SYSTEM AND FOR FOOTING
DRAWINGS GARAGE SEE GARAGE UNDERPINNING
DRAWINGS 6" 2
2'-2" 6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6" 14'-0 1/2" 9'-7 1/2" 6'-4"
S223-OF RESERVED FOR REVIEWERS NOTES
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"
E1 1 2 3 4 5 6 7 8 9 11 12 13 14 E2
1 LEVEL B3
3/32" = 1'-0"
REV. DATE ISSUE TITLE
.016 05/03/2021 ADDENDUM 08
NOTE TO CONTRACTOR:
FIELD VERIFY ALL EXISTING DIMENSIONS & ELEVATIONS
PRIOR TO FABRICATION OF MATERIALS AND CONSTRUCTION
PLAN NOTES:
MAPLE TERRACE
3001 MAPLE AVENUE
1. NORTH ARROW DALLAS, TEXAS, 75201
2. SEE SHEET S101-OF FOR TYPICAL PLAN NOTES, SYMBOLS, ABBREVIATIONS AND LEVEL B3 FRAMING PLAN
TYPICIAL DETAIL SHEET LIST.
3. SEE SHEET S101-OF, S102-OF AND S103-OF FOR GENERAL NOTES
190013
PROJECT NUMBER
S200A-OF S H E E T N U M B E R
1
S220-OF
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

(David Leff)
Dallas, TX 75202
GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
Dallas, TX 75226
GEOTECH
ECS Southwest, LLP
RETENTION SYSTEM
E-B.5 7'-1 1/4" FOR OFFICE BUILDING CIVIL ENGINEER
Kimley-Horn and Associates, Inc.
1'-9" 9" 13455 Noel Road, Two Galleria Office Tower, Suite 700
18 18 13
13 OUTLINE OF BUILDING ABOVE Dallas, TX 75240
S306-OF S306-OF S305-OF (972-770-1300 Alex Rathbun)
S305-OF
E-C LANDSCAPE ARCHITECT

SWA Group
6'-4"
7'-1"
9"
2001 Irving Boulevard, Suite 157
9"
9"
Dallas, TX 75207
A 8 1
S16
BB201 1'-7"
S222-OF STRUCTURAL
BB201
S304-OF
15
4 13 Datum Engineers
3
S15
S502-OF 6516 Forest Park Road
8
19'-3"
STAIR 1 S222-OF S222-OF S305-OF OUTLINE OF Dallas, TX 75235
SW-1
S304-OF BASEMENT (214-358-0174 Rodolfo D'Arlach)
S14
7 8 TEMPORARY WALL ABOVE
A8
S8
14 10 RETENTION SYSTEM
S411-OF S304-OF MEP ENGINEER
S305-OF S502-OF T.O.S.C. EL. = 461'-8" ME Engineers, Inc.
BB202 1825 Market Center Blvd., Suite 600
B 4 Dallas, TX 75207
5"
18
S306-OF ADDN'L 3#6X20'-0" (214-741-1589 Drew Shivley)
S306-OF OUTLINE OF
2 SW-2 @6" TOP & BOT. 2
STAIR TO NEW ELEVATOR CONSULTANT
14 5 S222-OF RESIDENTIAL
S221-OF Persohn | Hahn Associates, Inc.
S305-OF S502-OF 2 TOWER GARAGE 8612 Broad Meadow Lane
S13
S222-OF McKinney, TX 75071
TEMPORARY (972-832-4232 Tom Williams)
30'-7 1/4"
RETENTION SYSTEM
B.5 7 INTERIOR DESIGNER
S306-OF Rottet Studio
RETENTION SYSTEM 808 Travis Street, Suite 100
FOR OFFICE BUILDING Houston, TX 77002
14'-6"
(713-221-1830 x 6105 Anja Majkic)

18
S306-OF
1'-9"
OUTLINE OF BUILDING ABOVE
C OUTLINE OF BUILDING ABOVE
1" E.J. Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
11 Datum Project No. 19166

S307-OF DATE ISSUE TITLE
SEE GARAGE DRAWINGS FOR 1 04/03/2020 SCHEMATIC DESIGN PRESENTATION

OUTLINE OF CONTINUATION OF RETENTION SEE GARAGE DRAWINGS FOR 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
S223-OF
RESIDENTIAL SYSTEM AND FOR FOOTING RESIDENTIAL RETENTION SYSTEM AND SEE GARAGE DRAWINGS FOR 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
TOWER GARAGE UNDERPINNING TOWER GARAGE GARAGE WALLS CONTINUATION OF RETENTION 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
SEE GARAGE SEE GARAGE SYSTEM AND FOR FOOTING 10/30/2020 ISSUE FOR PERMIT
DRAWINGS DRAWINGS UNDERPINNING 12/18/2020 90% CONSTRUCTION DOCUMENTS
2'-2" 6" 14'-0 1/2" 9'-7 1/2" 6'-4" 01/25/2021 100% CONSTRUCTION DOCUMENTS
6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6"
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"

2 RESERVED FOR REVIEWERS NOTES
S223-OF
E1 1 2 3 4 5 6 7 8 9 11 12 13 14 E2
1 LEVEL B2 REV. DATE ISSUE TITLE

3/32" = 1'-0"
NOTE TO CONTRACTOR:
PLAN NOTES:
MAPLE TERRACE
3001 MAPLE AVENUE
190013
PROJECT NUMBER
S200B-OF S H E E T N U M B E R
E-1.1 3 4 E-1.2 5
NOTE:
SCAN AND LOCATE EXIST E-A E-B
REINF. SEE NOTE 7 AND 8 14
3/S601-OF
ON FIELD DRILLED ANCHOR 6" +/- 6" +/-
NOTES ON S102-OF S601-OF
E-C
2'-0"
LEVEL 01
6" +/-
481'-2"
1" GAP 6" THICK SLAB-ON-GRADE DEVELOPER
Hines
9 A 2200 Ross Avenue, Suite 4200W
S601-OF Dallas, TX 75201
8
15 (972-716-2908 Corbin Eckel)
.016 S304-OF
BB101
BB101
S502-OF 2800 Post Oak Blvd., 49th Floor
1/4 ELEV. SE1
Houston, TX 77056
S11
5'-6 1/2" 2'-0" (713-621-8000 Juan Delgado)
1'-0" 6'-8"
EQUITY PARTNERS
10 McNair Interests
S12
S502-OF 109 N. Post Oak Lane, Suite 600
LEVEL B1 ADDN'L 3#6 X 20'-0" Houston, TX 77024
C10X15.3 EA. SIDE 471'-0" @ 6" TOP & BOT. (Drew Steffen)
T.O.S.C. EL. = 471'-0"
W/ 3/4" DIA. THRU BB102 .016 Mitsui Fudosan America
BOLTS @ 12"
B 1251 Avenue of the Americas, Suite 800
4" CURB ON TOP OF TOPPING (David Leff)
.016 SLAB, SEE ARCH'L.
3 EXISTING BASEMENT WALL OPENING REINF. W/#3@12" E.W.
(POUR MONOLITHIC WITH SLAB.)
.016 16
S502-OF
1/4" = 1'-0" 5G Studio Collaborative, LLC.
1 1217 Main St., Suite 500
Dallas, TX 75202
2 LEVEL B1 - SERVICE LOBBY (214-347-4982 Christine Robbins-Elrod)
1/8" = 1'-0" MASTER/MULTIFAMILY ARCHITECT

GFF Architects
E-0 E-0.4E-0.6
E-0.4 E-0.6 E1 E-1.1 E-1.2 E-1.3 E-1.4 E-1.5 E-1.6 E-1.7 E-1.8 E2 E-2.3 E-2.6 Dallas, TX 75201
16'-0 7/8" 5'-7 7/8" 14'-6 1/4" 12'-8 3/4" 22'-7 3/4" 19'-0" 15'-6" 14'-9 1/4" 15'-5 1/8" 18'-10" 22'-9 1/2" 12'-9 3/4" 15'-1 7/8" 21'-1 1/8"
1 ZONING/ENTITLEMENT
CONTRACTOR SHALL VERIFY EXISTING
COLUMN SIZE AND REINF. AND REPORT TO S220-OF Baldwin Associates
ENGINEER. THIS WORK IS TO BE 3904 Elm Street, Suite B
PERFORMED PRIOR TO TERRACE LEVEL Dallas, TX 75226
SEE EAST RESTAURANT SET (214-824-7949 Robert Baldwin)
PLATFORM WORK. COLUMN BEEF UP MAY
BE REQUIRED IN THESE LOCATIONS. FOR CONNECTION
CONTRACTOR CARRY CONTINGENCY, TO EXISTING BASEMENT GEOTECH
SEE 14 AND 20/610A-OF . ECS Southwest, LLP
E-A E-A (972-392-3222 Siddharth Neekhra)
EXIST. T.O.S.C. EL. = 472'-1 1/2" (F.V.)
3/S200C-OF
OFFICE MECHANICAL YARD 1" E.J. 17/S612-OF FIELD VERIFY EXTENTS OF CIVIL ENGINEER
13'-11 1/2"
SEE 1/S230-OF AND ARCH'L .016 NEW METAL STAIR SECT "A" 17/S610A-OF EXISTING FOOTING PRIOR TO
SEE ARCH'L Kimley-Horn and Associates, Inc.
20/S610A-OF PIER DRILLING OPERATIONS. 13455 Noel Road, Two Galleria Office Tower, Suite 700
20/S610A-OF 17/S612-OF 20/S610A-OF Dallas, TX 75240
SECT"B" BUILT UP SLAB 0N (972-770-1300 Alex Rathbun)
20/S601-OF
E-B STYROFOAM SEE

E-B
17/S601-OF
6" FIELD VERIFY SIZE, DEPTH, ARCH'L AND LANDSCAPE ARCHITECT
T.O.S.C. EL. = 472'-1 1/2" (F.V.) T.O.S.C. EL. = 471'-6" (F.V.) 20/S610A-OF
8'-9 3/4"
LOUVER IN EXIST. AHU 7'-1 1/4" THICKNESS AND LOCATION OF 17/S307-OF SWA Group
WINDOW/WALL 4,500# EXIST. FOOTING PRIOR TO SIM. 2001 Irving Boulevard, Suite 157
BEGINNING UNDERPINNING WORK. 1 NEW OPENING IN EXISTING
E-B.5 10 13 13 7/S601-OF
BASEMENT WALL
Dallas, TX 75207
S306-OF S306-OF 12 S306-OF 12 (4 LOCATIONS) E-B.5 (214-954-0016 Chuck McDaniel)
EXIST. T.O.S.C. EL. = 471'-2" (F.V.) RETENTION SYSTEM S306-OF S306-OF 15 5/S601-OF 18 A0 STRUCTURAL
1
A0 1 1'-0" S307-OF S307-OF
11'-5"
P=275k FOR OFFICE P=275k 9" Datum Engineers

P=275k 3/S601-OF
9'-9"
20/S610A-OF 1" E.J. SIM.

1 P=275k P=275k 8'-0" 6516 Forest Park Road
16'-10"
Dallas, TX 75235
5'-8"
E-C E-C
2'-0"
BASEMENT WALL BELOW
4'-0"
15 19 1" E.J.
6'-4"
MEP ENGINEER
7'-1"
4/S601-OF
NEW DOOR IN EXISING P1, CC/S302-OF

CONCRETE WALL S306-OF S306-OF TYP. AT ME Engineers, Inc.
FIELD VERIFY EXTENTS OF 6" THICK SLAB-ON-GRADE 1" E.J. SIM. 19
14'-7 5/8"
BASEMENT 1825 Market Center Blvd., Suite 600

A EXISTING FOOTING PRIOR TO
PIER DRILLING OPERATIONS, 8 1 WALLS W/O COL.
S306-OF
17 NEW DOOR OPENING A Dallas, TX 75207
S3 FOR RESTAURANT, SEE (214-741-1589 Drew Shivley)
TYP. 15 ELEV. SE1 S304-OF S222-OF S306-OF
C11 , P3
BB101
11 EAST RESTAURANT SET
BB101
16 PER ECS REPORT, EXISTING E/S302-OF
S502-OF 4 3 FOOTINGS ARE S503-OF SEE 14/S601-OF SIM. ELEVATOR CONSULTANT
E-2 E-2
S11
8 S306-OF
SW-3
ELEV. PE2 Persohn | Hahn Associates, Inc.
19'-3"
STAIR 1 S222-OF S222-OF 8' LONG X 5.67' WIDE X 1.5' THICK STAIR 2 EXISTING 36x80 (F.V.)
SW-1
S304-OF 8612 Broad Meadow Lane

PER ECS REPORT, EXISTING P=275k 1" E.J. T.O. FOOTING EL = 468 P4, TYP. AT OPENING TO BE INFILLED
2'-0" C11 , P3 McKinney, TX 75071
FOOTINGS ARE
S11
8 SHEARWALLS SEE 3/S613-OF

A8
14'-8 5/8"
S12
ELEV. E/S302-OF (972-832-4232 Tom Williams)

A8 8' LONG X 7.67' WIDE X 1.5' THICK 10 7
10 S304-OF PE1 3
16
P=275k
T.O. FOOTING EL = 465.5 P=275k S306-OF S411-OF 9/S304-OF S305-OF P=275k
S502-OF BB102 INTERIOR DESIGNER
S502-OF
B 4 11 B Rottet Studio
808 Travis Street, Suite 100
5"
OPTIONAL OUTLINE OF
8'-0"
S306-OF
SW-2 ADDN'L 3#6X20'-0"
S305-OF
TEMPORARY STAIR TO NEW
Houston, TX 77002
18/S601-OF
17 16 (713-221-1830 x 6105 Anja Majkic)

2 14 @6" TOP & BOT.
E-4 RETENTION
CRAWL SPACE ABOVE
RESIDENTIAL E-4
S10
S221-OF S306-OF S502-OF S502-OF

2 SYSTEM 12 TOWER GARAGE
FOOTING TO BE 3'-0" 2
S200C-OF TEMPORARY S503-OF 1" E.J.
UNDERPINNED BY 5 S222-OF S13
RETENTION SYSTEM RETENTION SYSTEM 6" SLAB-ON-GRADE
19'-0"
2'-4" UNDERPINNING S306-OF 7'-8" 19

30'-7 1/4"
FOR OFFICE BUILDING SEE S303-OF

CONTRACTOR 7/S601-OF S306-OF
B.5 (PERFORMANCE SPEC.) (2 LOCATIONS)
P=275k
P2 BASEMENT
FIELD VERIFY EXTENTS OF
B.5 www.datumengineers.com | Co. Reg. No. F-2819
Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
C4 20CC/S302-OF C4 , P2 WALL BELOW
20F/S401-OF D/S302-OF T.O.S.C. EL. = 471'-9" EXISTING FOOTING PRIOR TO Datum Project No. 19166
5'-4"
PIER DRILLING OPERATIONS.

E-7 T.O.S.C. EL. = 471'-0" E-7
S9
7/S306-OF
14'-6"
DATE ISSUE TITLE

18 7
2'-1 3/4"
P=275k 04/03/2020 SCHEMATIC DESIGN PRESENTATION

S305-OF C2,20F/S401-OF C2 , P3 S305-OF
E/S302-OF 6 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
6'-4"
14'-4 3/4"
20/S610A-OF P3,20CC/S302-OF 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT

S305-OF
C P=150k P=275k C
5'-9 3/4"

EXISTING FOOTING. FIELD P=150k 12/18/2020 90% CONSTRUCTION DOCUMENTS
1'-9"
VERIFY SIZE, DEPTH, 9" 01/25/2021 100% CONSTRUCTION DOCUMENTS

E-D THICKNESS AND LOCATION -/--- 20/S305-OF
1" E.J.
E-D
PRIOR TO BEGINNING 1 17 11 2
UNDERPINNING WORK
S223-OF S305-OF S307-OF S223-OF RESERVED FOR REVIEWERS NOTES
SEE GARAGE DRAWINGS FOR
CONTINUATION OF RETENTION EXISTING WALL EXISTING 36x80 (F.V.) SEE GARAGE DRAWINGS FOR SEE GARAGE DRAWINGS FOR
5'-0"
SYSTEM AND FOR FOOTING AND STAIR TO OPENING TO BE INFILLED RETENTION SYSTEM AND CONTINUATION OF RETENTION
UNDERPINNING BE DEMO'D SEE 3/S613-OF GARAGE WALLS SYSTEM AND FOR FOOTING
8'-6" UNDERPINNING
154'-6" (F.V.)
OUTLINE OF
RESIDENTIAL 6"
TOWER GARAGE 13'-0 1/4" 6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
SEE GARAGE
DRAWINGS EXISTING 76x62 (F.V.) 30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"
OPENING TO BE INFILLED
(3 LOCATIONS) SEE 3/S613-OF

1 2 3 4 5 6 7 8 9 10 11 12 13 14 .05 12/18/2020 Permit Set Update
1 02/09/2021 ADDENDUM 1
.016 05/03/2021 ADDENDUM 08
1 LEVEL B1
3/32" = 1'-0"
NOTE TO CONTRACTOR:
PLAN NOTES:
MAPLE TERRACE
3001 MAPLE AVENUE
1. NORTH ARROW
190013
PROJECT NUMBER
S200C-OF S H E E T N U M B E R
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
E-0.4 E-0.6 E1 E-1.1 E-1.2 E-1.3 E-1.4 E-1.5 E-1.6 E-1.7 E-1.8 E2 E-2.3 E-2.6 New York, New York 10020
(David Leff)
C
CONTRACTOR SHALL VERIFY EXISTING OFFICE/RETAIL ARCHITECT
COLUMN SIZE AND REINF. AND REPORT TO 5G Studio Collaborative, LLC.
ENGINEER. THIS WORK IS TO BE 43'-2 3/4" (F.V.) 1217 Main St., Suite 500
Dallas, TX 75202
PERFORMED PRIOR TO TERRACE LEVEL
EXISTING LOUVER (214-347-4982 Christine Robbins-Elrod)
CONTRACTOR SHALL VERIFY EXISTING PLATFORM WORK. COLUMN BEEF UP MAY C
OPENING TO BE INFILLED BE REQUIRED IN THESE LOCATIONS. 1
COLUMN SIZE AND REINF. AND REPORT TO SEE 3/S613-OF , TYP. COLUMN SIZE AND REINF. AND REPORT TO MASTER/MULTIFAMILY ARCHITECT
CONTRACTOR CARRY CONTINGENCY, S220-OF
ENGINEER. THIS WORK IS TO BE ENGINEER. THIS WORK IS TO BE GFF Architects
5'-6 1/4" (F.V.)

PERFORMED PRIOR TO TERRACE LEVEL SEE 14 AND 20/610A-OF PERFORMED PRIOR TO TERRACE LEVEL
EXISTING SLAB OPENING 2808 Fairmount St., Suite 300
PLATFORM WORK. COLUMN BEEF UP MAY NEW DOOR AT EXISTING WIDOW 16 PLATFORM WORK. COLUMN BEEF UP MAY Dallas, TX 75201
LOCATION, SEE ARCH'L TO BE INFILLED, SEE
BE REQUIRED IN THESE LOCATIONS. S307-OF 3'-6" BE REQUIRED IN THESE LOCATIONS. (214-303-1500 Michael Reyes)
CONTRACTOR CARRY CONTINGENCY, CONTRACTOR CARRY CONTINGENCY,
SEE 14 AND 20/610A-OF . EXISTING LOUVER SEE 14 AND 20/610A-OF ZONING/ENTITLEMENT
OPENING TO BE INFILLED
2'-1"
Baldwin Associates
SEE 3/S613-OF, TYP. 3904 Elm Street, Suite B
E-A 6'-2 1/2"
E-A Dallas, TX 75226
C
18/S610A-OF
COLUMN SIZE AND REINF. AND REPORT TO
GEOTECH
16/S610-OF SIM. ENGINEER. THIS WORK IS TO BE ECS Southwest, LLP
18/S610A-OF 18/S610A-OF PERFORMED PRIOR TO TERRACE LEVEL 3033 Kellyway Drive, Suite 110
PLATFORM WORK. COLUMN BEEF UP MAY (972-392-3222 Siddharth Neekhra)
20/S601-OF
BE REQUIRED IN THESE LOCATIONS.

E-B E-B
17/S601-OF
ADDN'L 3#7X12'-0" CONTRACTOR CARRY CONTINGENCY, CIVIL ENGINEER
18/S610A-OF 18/S610A-OF
BOT. FROM EDGE 19'-8 1/2" 23'-10" 8 SEE 14 AND 20/610A-OF
OF SLAB INTO B110 S601-OF 10/S601-OF 10/S601-OF 13455 Noel Road, Two Galleria Office Tower, Suite 700
11/S601-OF
E-B.5 O.H. 1
Dallas, TX 75240
14
3 W12X35 W12X35 W12X35 E-B.5 (972-770-1300 Alex Rathbun)
S613-OF 6 BASEMENT
5/S601-OF A0
A0
11'-5" (F.V.)
18/S610A-OF S307-OF
S601-OF
WALL BELOW 11/S601-OF LANDSCAPE ARCHITECT
3/S601-OF EXISTING LOUVER SWA Group
9'-9"
16/S610-OF 10 16/S610-OF 1/S630-OF BASEMENT WALL

EXISTING STAIR OPENING TO BE INFILLED 2001 Irving Boulevard, Suite 157
5'-4 3/8"
WB-1
(F.V.)
TO BE DEMO'D S305-OF SEE 3/S613-OF, TYP. BELOW Dallas, TX 75207

15
ADDN'L 3#7X12'-0" (214-954-0016 Chuck McDaniel)
E-C S613-OF 20 10 20 10 4
C8 , P3
BOT. FROM EDGE OF E-C
S6
C9 , P5
S6
S6
S6
4'-6" 4 STRUCTURAL
7'-1"
4/S601-OF
1 7'-10" (F.V.) S410-OF S410-OF S410-OF S410-OF S305-OF D/S302-OF SLAB INTO B110
D/S302-OF
B110 B111 B112 S305-OF B113 EXISTING STAIR Datum Engineers
6516 Forest Park Road
A 1 20 8
7 TO BE DEMO'D
SEE ARCH'L
A Dallas, TX 75235
S222-OF S502-OF 6 EXISTING STAIR S411-OF
S3 (214-358-0174 Rodolfo D'Arlach)
ELEV. SE1 S304-OF 9
S3 TO BE DEMO'D EXISTING STAIR TO BE
9 S307-OF
S11
B108
4 3 DEMO'D SEE ARCH'L S503-OF MEP ENGINEER
B108
S11
E-2 S307-OF ELEV. PE2
8
OPTIONAL TEMPORARY E-2
19'-3"
STAIR 1 S222-OF S222-OF ME Engineers, Inc.
SW-3
B109
S11
ADDN'L 3#7X12'-0" 5 S305-OF AHU
B109
SW-1
S11
RETENTION SYSTEM 4 1825 Market Center Blvd., Suite 600
5,000#
S11
BOT. FROM EDGE S502-OF STAIR 2 Dallas, TX 75207
OF SLAB INTO B105 T.O.S.C. EL. = 481'-2" 8 ELEV. T.O.S.C. EL. = 481'-2" S305-OF BASEMENT WALL (214-741-1589 Drew Shivley)
9/S304-OF
A8 A8
S12
10 5 7 8 BELOW
SEE LEVEL 03 (S203-OF) S304-OF PE1
S306-OF S307-OF S411-OF S503-OF
FOR ADDN'L INFO. NOT B106 ELEVATOR CONSULTANT
B SHOWN AT INFILL, TYP. B Persohn | Hahn Associates, Inc.
5"
B105 B107 8612 Broad Meadow Lane

SW-2 C5 , P5 C8 , P3 OUTLINE OF STAIR TO McKinney, TX 75071
18/S601-OF
NEW RESIDENTIAL
S17
E/S302-OF D/S302-OF (972-832-4232 Tom Williams)
E-4 15'-10" 2 20'-5" 10 TEMPORARY 10 3
TOWER GARAGE E-4
S11
S10
S17
19 18 EXISTING STAIR
S221-OF S410-OF RETENTION S307-OF S307-OF
S10
10/S601-OF, 3 S502-OF S502-OF FLOOR DESIGNED FOR ONE TO BE DEMO'D INTERIOR DESIGNER
SYSTEM 8
S10
SIM. S307-OF 2 FUTURE INTERFLOOR STAIR ON INFILL EXISTING Rottet Studio
ADDN'L 3#6X20'-0" 4
S10
W12X35
S305-OF EITHER SIDE OF BRIDGE.
S10
@6" TOP & BOT. S222-OF 14 WINDOW OPENING 808 Travis Street, Suite 100
30'-7 1/4"
B103 S305-OF P DL = 6k, P LL = 6k RETENTION SYSTEM Houston, TX 77002

EXISTING STAIR S307-OF
FOR OFFICE BUILDING WITH CMU, ALL LEVELS
4 (713-221-1830 x 6105 Anja Majkic)
B.5 16/S610-OF TO BE DEMO'D S307-OF
B.5
10/S601-OF, B104 P4, CC/S302-OF P1, CC/S302-OF 20/S610A-OF
T.O.S.C. EL. = 481'-2" 20
SIM. P=250k
E-7 E-7
S9
S9
P=250k
14'-6"
S410-OF P1, CC/S302-OF

16/S610-OF
S9
S9
S9
C1 , P3
W12X35
E/S302-OF P3, 20CC/S302-OF
2'-8 1/2"
BASEMENT WALL BELOW FIELD VERIFY EXTENTS OF www.datumengineers.com | Co. Reg. No. F-2819
3 C1 , P3, E/S302-OF Dallas Austin San Antonio
B101 B102 EXISTING FOOTING PRIOR TO 214-358-0174 512-469-9490 210-858-2880
S307-OF
C 8 PIER DRILLING OPERATIONS.
C Datum Project No. 19166
5'-9 3/4"
(F.V.)
15k
S601-OF
P=150k P=200k DATE ISSUE TITLE
04/03/2020 SCHEMATIC DESIGN PRESENTATION
C1,20F/S401-OF
E-D E-D
2'-10"
13/S307-OF
EXISTING WALL 1 1" E.J. 2 5 2 1
TO BE DEMO'D S307-OF S305-OF S223-OF S307-OF 5'-0" SEE GARAGE DRAWINGS FOR
16/S610-OF S223-OF 10/30/2020 ISSUE FOR PERMIT
13/S601-OF CONTINUATION OF RETENTION 12/18/2020 90% CONSTRUCTION DOCUMENTS
RESIDENTIAL SEE GARAGE DRAWINGS FOR SYSTEM AND FOR FOOTING
INFILL EXISTING WINDOW TOWER GARAGE RETENTION SYSTEM AND 01/25/2021 100% CONSTRUCTION DOCUMENTS
OPENING WITH CMU, ALL UNDERPINNING P=150k
GARAGE WALLS
LEVELS
RESERVED FOR REVIEWERS NOTES
154'-6" (F.V.)
2'-2" (F.V.) 6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4" (F.V.)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 LEVEL 01 REV. DATE ISSUE TITLE

3/32" = 1'-0" .05
0 12/18/2020 Permit Set Update
1 02/09/2021 ADDENDUM 1
NOTE TO CONTRACTOR:
PLAN NOTES: MAPLE TERRACE

3001 MAPLE AVENUE
2. SEE SHEET S101-OF FOR TYPICAL PLAN NOTES, SYMBOLS, ABBREVIATIONS AND LEVEL 01 FRAMING PLAN
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
E-0.4 E-0.6 E1 E-1.1 E-1.2 E-1.3 E-1.4 E-1.5 E-1.6 E-1.7 E-1.8 E2 E-2.3 E-2.6 1251 Avenue of the Americas, Suite 800
(David Leff)
Dallas, TX 75202
C
COLUMN SIZE AND REINF. AND REPORT TO MASTER/MULTIFAMILY ARCHITECT
CONTRACTOR SHALL VERIFY EXISTING 5
ENGINEER. THIS WORK IS TO BE GFF Architects
2 1 PERFORMED PRIOR TO TERRACE LEVEL
COLUMN SIZE AND REINF. AND REPORT TO S610-OF
S610-OF
ENGINEER. THIS WORK IS TO BE S220-OF PLATFORM WORK. COLUMN BEEF UP MAY Dallas, TX 75201
PERFORMED PRIOR TO TERRACE LEVEL BE REQUIRED IN THESE LOCATIONS. (214-303-1500 Michael Reyes)
PLATFORM WORK. COLUMN BEEF UP MAY CONTRACTOR CARRY CONTINGENCY,
BE REQUIRED IN THESE LOCATIONS. SEE 14 AND 20/610A-OF . ZONING/ENTITLEMENT
CONTRACTOR CARRY CONTINGENCY, Baldwin Associates
SEE 14 AND 20/610A-OF . 3904 Elm Street, Suite B
E-A E-A Dallas, TX 75226
13'-11 1/2"
GEOTECH
ECS Southwest, LLP
E-B E-B CIVIL ENGINEER
2 5 13455 Noel Road, Two Galleria Office Tower, Suite 700
EXISTING STAIR Dallas, TX 75240
S411-OF S411-OF
E-B.5 ROOF TO BE DEMO'D
11
E-B.5 (972-770-1300 Alex Rathbun)
CONTRACTOR
C SHALL VERIFY EXISTING
27'-3 3/4"
9 EXISTING STAIR 5/S601-OF

S610A-OF ADDN'L 4#7X12'-0" BOT. COLUMN SIZE AND REINF. AND REPORT TO LANDSCAPE ARCHITECT
S411-OF ROOF TO BE DEMO'D 1" E.J.
1/S630-OF
FROM EDGE OF SLAB ENGINEER. THIS WORK IS TO BE SWA Group
EXISTING STAIR INTO B211 2001 Irving Boulevard, Suite 157
1" E.J.
ROOF TO BE DEMO'D
WB-1 PERFORMED PRIOR TO TERRACE LEVEL
PLATFORM WORK. COLUMN BEEF UP MAY Dallas, TX 75207
E-C ADDN'L 3#7X12'-0" BE REQUIRED IN THESE LOCATIONS. E-C
5'-2 1/2" 2'-2 1/2"

4'-6" EXISTING STAIR CONTRACTOR CARRY CONTINGENCY,
S6
S6
S6
S6
S6
S6
BOT. FROM EDGE OF SM33A STRUCTURAL
7'-1"
4'-6" B204 B205 4'-6" B211 4'-6" ROOF TO BE DEMO'D

SLAB INTO B201 B201 B202 9 SEE 14 AND 20/610A-OF
Datum Engineers
S410-OF
A B203 1
SC33 A 6516 Forest Park Road
Dallas, TX 75235
9"
S3 7 (214-358-0174 Rodolfo D'Arlach)
14 S222-OF 4'-6" 16 S3
S502-OF S410-OF
S503-OF
SC35
ELEV. SE1 ELEV. PE2 MEP ENGINEER
B212
B212
E-2 ADDN'L 3#7X12'-0" STAIR 2 E-2
PTB203
T.O.S.C. EL. = 491'-2"
B210
B213
19'-3"
B209
ME Engineers, Inc.
SW-3
S5
S5
S5
BOT. FROM EDGE STAIR 1
SW-1
OF SLAB INTO B206 SM33B 1825 Market Center Blvd., Suite 600
2'-3 3/4"
SM34
SM35
SC34
Dallas, TX 75207
S11
DROP IN SLAB
9/S304-OF (214-741-1589 Drew Shivley)
A8 ELEV. PE1 A8
S8
SEE LEVEL 03 (S203-OF) BOTTOM
PTB204 PTB205 PTB207 9
FOR ADDN'L INFO. NOT B208 ELEVATOR CONSULTANT
B206 B207
SHOWN AT INFILL, TYP. S410-OF
B 6" PTB206
B Persohn | Hahn Associates, Inc.
1'-6"
2'-0"
5"
8612 Broad Meadow Lane
2'-0"
1" E.J. SW-2 T.O.S.C. EL. = 491'-2"
1" E.J. ADDN'L 4#7X12'-0" BOT. McKinney, TX 75071
(972-832-4232 Tom Williams)
E-4 11
2 13
ADDN'L 3#6X20'-0" @ 6"
TOP & BOT. STRESSING END FOR
1'-1" 4'-6" 5'-0" FROM EDGE OF SLAB
INTO PTB207
E-4
12 S222-OF S502-OF
S502-OF ADDN'L P-T FOR BEAMS D/S402-OF 17
7
INTERIOR DESIGNER
S502-OF 1 6 TYP. S503-OF
PTB 205 - PTB 207 Rottet Studio
2 S410-OF
S503-OF S411-OF 808 Travis Street, Suite 100
30'-7 1/4"
PTB201
PTB202
S610A-OF Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
BEAM DESIGNED FOR ONE FUTURE S7 18/S610A-OF
S9
INTERFLOOR STAIR ON EITHER
SIDE OF BRIDGE.
E-7 P DL = 6k, P LL = 6k 4'-8 1/2" E-7
CONTRACTOR
C SHALL VERIFY EXISTING www.datumengineers.com | Co. Reg. No. F-2819
PTB208 COLUMN SIZE AND REINF. AND REPORT TO Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
ENGINEER. THIS WORK IS TO BE
C C Datum Project No. 19166
2'-8"
DATE ISSUE TITLE
1'-2"
E-D 1
CURTAIN WALL
2 13/S307-OF CONTRACTOR CARRY CONTINGENCY, E-D 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
S223-OF SEE ARCH'L S223-OF 23'-8" SEE 14 AND 20/610A-OF
ENGINEER. THIS WORK IS TO BE 01/25/2021 100% CONSTRUCTION DOCUMENTS

BE REQUIRED IN THESE LOCATIONS. RESERVED FOR REVIEWERS NOTES
CONTRACTOR CARRY CONTINGENCY,
2'-2"
SEE 14 AND 20/610A-OF .
6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 19'-4" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 LEVEL 02
3/32" = 1'-0"
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

(David Leff)
Dallas, TX 75202
A0 (214-347-4982 Christine Robbins-Elrod)
1" E.J. GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
E-C Baldwin Associates
ADDN'L 3#7X12'-0" BOT. 3904 Elm Street, Suite B
S6
FROM EDGE OF SLAB #4@10"@BOT. Dallas, TX 75226
SM23
SM26
SM29
SC23
SC26
SC29
SC32
ADDN'L 3#7X12'-0" BOT.
S6
INTO B305
S6
S6
6" 4'-6"
7'-1"
4'-6"
1'-3"
FROM EDGE OF SLAB
8 1/2"
1'-3"
6'-9" 3'-4" FROM GL. 6 TO 12 INTO B313
9"
B305 B306 B307 GEOTECH
B313 ECS Southwest, LLP
SC13 SC14 3033 Kellyway Drive, Suite 110
A Carrollton, TX 75006
9"
9"
SC12
1'-7"
1'-0"
6'-0"
6'-0"
S3 7'-10"
SC15 CIVIL ENGINEER
ELEV. SE1 1'-2 1/2"
1'-3" Kimley-Horn and Associates, Inc.
13455 Noel Road, Two Galleria Office Tower, Suite 700
8'-2"
6" Dallas, TX 75240
3'-9"
ELEV. PE2 (972-770-1300 Alex Rathbun)
SC31
E-2
B304
5'-1 1/2"
10'-9 1/4"
SM25
LANDSCAPE ARCHITECT
B304
9'-4 1/4" STAIR 2
19'-3"
17'-9"
B313
B313
7'-3"
SC25
SC28
SW-3
B311
SM28
SM10A SWA Group
11'-8 5/8"
S1
S1
SM22
SC22
1'-0"
2 3/4" 2001 Irving Boulevard, Suite 157

SW-1
SM17
SM8A
SC17
SM17
SC17
SC19
SM9A Dallas, TX 75207

3" 2 3/4" (214-954-0016 Chuck McDaniel)
@ SOUTH OF
STAIR 1
1'-0"
ELEV. PE1
6"
5'-1 1/2"
STRUCTURAL
OPENING
ADDN'L 3#7X12'-0" BOT. 1'-3" 9'-4 1/4" STEP IN SLAB
2'-2"
S2
FROM EDGE OF SLAB ADDN'L 3#6X20'-0" 1'-10" Datum Engineers
BOTTOM
7'-2"
INTO B308 1'-7" @ 6", TOP & BOT 6516 Forest Park Road
6'-0"
6'-0"
6'-0"
A8 SC8A
SC9A SC10A
ADDN'L 4#7X12'-0" BOT. Dallas, TX 75235
9"
2'-3 7/8"
10"
9"
FROM EDGE OF SLAB
5"
B310
2'-0"
B308 B309 B312 INTO B312
B SC9B
MEP ENGINEER
SC10B ME Engineers, Inc.
SC8B 3'-1" 1'-1"
4'-6" SC5
SW-2 SC6 SC7 4'-6" SC11B 1825 Market Center Blvd., Suite 600
6'-0"
6'-0"
6'-0"
Dallas, TX 75207
E-4 4" CURB, SEE ARCH'L (214-741-1589 Drew Shivley)
REINF. W/#3@12" E.W.
ELEVATOR CONSULTANT
4'-6" Persohn | Hahn Associates, Inc.
SM08B McKinney, TX 75071
SM06 SM07 SM11B
SM05 SM9B SM10B (972-832-4232 Tom Williams)
6'-0" 6'-0" 6'-0" 6'-0"
INTERIOR DESIGNER
FLOOR DESIGNED FOR ONE
SM21
Rottet Studio
FUTURE INTERFLOOR STAIR ON 9" DEEP DROP 808 Travis Street, Suite 100
EITHER SIDE OF BRIDGE. PANEL, TYP. Houston, TX 77002
30'-7 1/4"
P DL = 6k, P LL = 6k (713-221-1830 x 6105 Anja Majkic)
SM1
SM24
SM27
SC27
SC30
SM18
SM16
SC21
SM2 SM3 SM4
SC16
SC24
SM16
SM18
SM20
SC16
SC18
SC20
SM2
8'-0"
8'-0"
214-358-0174 512-469-9490 210-858-2880

E-7 DATE ISSUE TITLE
ADDN'L 6#6X10'-0"
SM20
@ OPENING

SC2 W/ STANDARD HOOKS AT
SM20A
SC1 SC2 SC4 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT

8" O.C. WHERE SHOWN
6'-7"
SC3
7'-0"

B301 B302 B302 B302 B303
C
1'-8"
1" E.J.
E-D
1" E.J.
6"
5'-0" 5'-0" 5'-0" 5'-0" 5'-0" OPENING WIDTH 5'-0" 6'-0" 6'-0" 6'-0" 6'-0" 6'-0" 6" 5'-0" 5'-0"
1'-3"
NOTE: REV. DATE ISSUE TITLE

SEE S203-OF FOR SECTIONS .05 12/18/2020 Permit Set Update
AND DETAILS FOR NEW

OFFICE FLOORPLATE
6"
2'-2" 6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" 2'-4"
30'-0" 30'-0" 30'-0" 30'-0" 30'-0"
154'-6"
(FIELD VERIFY)
E1 1 2 E-1.1 3 4 E-1.2 5 E-1.3 6 7 E-1.4 E-1.5 8 9 E-1.6 10 E-1.7 11 12 E-1.8 13 14 E2
NOTE:
SEE SHEET S203-OF FOR
1 LEVEL 03 - SLAB REINFORCING INFORMATION NOT SHOWN.
3/16" = 1'-0"

3001 MAPLE AVENUE
2. SEE SHEET S101-OF FOR TYPICAL PLAN NOTES, SYMBOLS, ABBREVIATIONS AND
LEVEL 3 SLAB REINFORCING

190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
(David Leff)
2 5G Studio Collaborative, LLC.
19 S611-OF 19 1217 Main St., Suite 500
S611-OF S611-OF Dallas, TX 75202
1 (214-347-4982 Christine Robbins-Elrod)
CONTRACTOR SHALL VERIFY EXISTING O.H.
S220-OF
COLUMN SIZE AND REINF. AND REPORT TO C
CONTRACTOR SHALL VERIFY EXISTING MASTER/MULTIFAMILY ARCHITECT
ENGINEER. THIS WORK IS TO BE COLUMN SIZE AND REINF. AND REPORT TO GFF Architects
PERFORMED PRIOR TO TERRACE LEVEL ENGINEER. THIS WORK IS TO BE 2808 Fairmount St., Suite 300
PLATFORM WORK. COLUMN BEEF UP MAY PERFORMED PRIOR TO TERRACE LEVEL Dallas, TX 75201
BE REQUIRED IN THESE LOCATIONS. PLATFORM WORK. COLUMN BEEF UP MAY (214-303-1500 Michael Reyes)
CONTRACTOR CARRY CONTINGENCY, BE REQUIRED IN THESE LOCATIONS.
SEE 14 AND 20/610A-OF . CONTRACTOR CARRY CONTINGENCY, ZONING/ENTITLEMENT
SEE 14 AND 20/610A-OF Baldwin Associates
C6X8.2
C6X8.2
E-A E-A Dallas, TX 75226
GEOTECH
ECS Southwest, LLP
20 Kimley-Horn and Associates, Inc.
S611-OF 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
E-B.5 20 12 15
E-B.5 (972-770-1300 Alex Rathbun)
12 14 12 C
S611-OF S410-OF S410-OF COLUMN SIZE AND REINF. AND REPORT TO LANDSCAPE ARCHITECT
S410-OF S410-OF S410-OF SWA Group
O.H. 1/S630-OF ENGINEER. THIS WORK IS TO BE
1" E.J. 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
E-C 10 SIM. 10
BE REQUIRED IN THESE LOCATIONS. E-C
CONTRACTOR CARRY CONTINGENCY, STRUCTURAL
7'-1"
S410-OF S410-OF 9 SEE 14 AND 20/610A-OF

INFILL SEE Datum Engineers
S410-OF 15/S613-OF TYP. 6516 Forest Park Road
A 1
9
20 8
A Dallas, TX 75235
S410-OF 7 (214-358-0174 Rodolfo D'Arlach)
S222-OF S502-OF S304-OF
9/S304-OF S410-OF
E-2 13 13 STAIR 2 E-2
19'-3"
ME Engineers, Inc.
SW-3
STAIR 1 AHU S503-OF
S503-OF 1825 Market Center Blvd., Suite 600
C6X8.2
SW-1
5,000# NEW CHASE OPENINGS
ELEV. PE1 Dallas, TX 75207
NEW CHASE OPENINGS 7 SEE ARCH'L AND 2/S613-OF (214-741-1589 Drew Shivley)
7
A8 SEE ARCH'L AND 2/S613-OF
7 7 8
S304-OF S503-OF S411-OF TYP. A8
S410-OF S411-OF 9
TYP. ELEVATOR CONSULTANT
S410-OF
B 5 B Persohn | Hahn Associates, Inc.
5"
T.O.S.C. EL. = 501'-2"

E-4 S410-OF
SW-2 10 3
McKinney, TX 75071
19 S410-OF S410-OF E-4
19 18
2 INTERIOR DESIGNER
S502-OF S502-OF S410-OF
S222-OF Rottet Studio
16 INFILL EXISTING 808 Travis Street, Suite 100
30'-7 1/4"
INFILL EXISTING S410-OF PLUMBING CHASE Houston, TX 77002

PLUMBING CHASE 3 18 SEE 11/S613-OF (713-221-1830 x 6105 Anja Majkic)
SEE 11/S613-OF S410-OF S410-OF
E-7 2 E-7
S410-OF
C
CONTRACTOR SHALL VERIFY EXISTING www.datumengineers.com | Co. Reg. No. F-2819
2 Dallas Austin San Antonio
COLUMN SIZE AND REINF. AND REPORT TO 214-358-0174 512-469-9490 210-858-2880
S410-OF ENGINEER. THIS WORK IS TO BE
C PERFORMED PRIOR TO TERRACE LEVEL
DATE ISSUE TITLE
1" E.J. BE REQUIRED IN THESE LOCATIONS.
E-D 1" E.J. CURTAIN WALL CONTRACTOR CARRY CONTINGENCY, E-D 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SEE ARCH'L SEE 14 AND 20/610A-OF
CONTRACTOR SHALL VERIFY EXISTING 1 1
COLUMN SIZE AND REINF. AND REPORT TO S221-OF S410-OF

SEE 14 AND 20/610A-OF . 154'-6" (F.V.)
2'-2" 6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"

NOTE:
SEE S203A-OF FOR BEAM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 MARKS, SLAB MARKS AND
DIMENSION CONTROL FOR
NEW OFFICE FLOORPLATE
1 LEVEL 03
3/32" = 1'-0"
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
(David Leff)
Dallas, TX 75202
CONTRACTOR SHALL VERIFY EXISTING S220-OF
ENGINEER. THIS WORK IS TO BE C
CONTRACTOR SHALL VERIFY EXISTING GFF Architects
PERFORMED PRIOR TO TERRACE LEVEL COLUMN SIZE AND REINF. AND REPORT TO 2808 Fairmount St., Suite 300
PLATFORM WORK. COLUMN BEEF UP MAY ENGINEER. THIS WORK IS TO BE Dallas, TX 75201
BE REQUIRED IN THESE LOCATIONS. PERFORMED PRIOR TO TERRACE LEVEL (214-303-1500 Michael Reyes)
CONTRACTOR CARRY CONTINGENCY, PLATFORM WORK. COLUMN BEEF UP MAY
SEE 14 AND 20/610A-OF . BE REQUIRED IN THESE LOCATIONS. ZONING/ENTITLEMENT
Dallas, TX 75226
E-A E-A (214-824-7949 Robert Baldwin)
13'-11 1/2"
GEOTECH
ECS Southwest, LLP
Dallas, TX 75240
E-B.5 E-B.5 (972-770-1300 Alex Rathbun)
C
27'-3 3/4"
2 4 5 LANDSCAPE ARCHITECT
ENGINEER. THIS WORK IS TO BE SWA Group
S411-OF S411-OF S411-OF 1/S630-OF
2" E.J. 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
E-C BE REQUIRED IN THESE LOCATIONS. E-C
4'-6" 4'-6" 4'-6" 4'-6" 4'-6" CONTRACTOR CARRY CONTINGENCY, STRUCTURAL
7'-1"
SEE 14 AND 20/610A-OF Datum Engineers

A 9 A Dallas, TX 75235
9"
S410-OF (214-358-0174 Rodolfo D'Arlach)
1'-7"
T.O.S.C. EL. = 511'-2"
9"
MEP ENGINEER
E-2 E-2
B404
ME Engineers, Inc.
19'-3"
SW-3
STAIR 1 1825 Market Center Blvd., Suite 600
SW-1
STAIR 2
Dallas, TX 75207
9/S304-OF (214-741-1589 Drew Shivley)
A8 7
T.O.S.C. EL. = 511'-2" A8
B403 ELEVATOR CONSULTANT
9"
S410-OF B401 B402
B B Persohn | Hahn Associates, Inc.
E-4 SW-2 1'-3"
BEAM DESIGNED FOR ONE FUTURE
McKinney, TX 75071
2" E.J. INTERFLOOR STAIR ON EITHER
2" E.J. E-4
SEE LEVEL 03 (S203-OF) 6
1 6 SIDE OF BRIDGE. INTERIOR DESIGNER
FOR ADDN'L INFO. NOT P DL = 6k, P LL = 6k S411-OF
S503-OF S411-OF Rottet Studio
SHOWN AT INFILL, TYP. 808 Travis Street, Suite 100
30'-7 1/4"
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
E-7 E-7
C
CONTRACTOR SHALL VERIFY EXISTING Dallas Austin San Antonio
DATE ISSUE TITLE
PLATFORM WORK. COLUMN BEEF UP MAY 04/03/2020 SCHEMATIC DESIGN PRESENTATION
E-D CURTAIN WALL CONTRACTOR CARRY CONTINGENCY, E-D 05/06/2020 ISSUE FOR SCHEMATIC DESIGN

CONTRACTOR CARRY CONTINGENCY, 2'-2"

6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
SEE 14 AND 20/610A-OF .

30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"
TYPICAL SECTIONS,
DIMENSION CONTROL
AND REINFORCING
1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 LEVEL 04 .05 12/18/2020 Permit Set Update
3/32" = 1'-0"
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
1
S220-OF
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
(David Leff)
Dallas, TX 75202
19
GFF Architects
S611-OF
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
13'-11 1/2"
CONTRACTOR SHALL VERIFY EXISTING GEOTECH

ECS Southwest, LLP
ENGINEER. THIS WORK IS TO BE 14/S610A-OF 14/S610A-OF 14/S610A-OF 3033 Kellyway Drive, Suite 110
PERFORMED PRIOR TO TERRACE LEVEL Carrollton, TX 75006
PLATFORM WORK. COLUMN BEEF UP MAY (972-392-3222 Siddharth Neekhra)
E-B CONTRACTOR CARRY CONTINGENCY, 14/S610A-OF CIVIL ENGINEER
SEE 14 AND 20/610A-OF . 14/S610A-OF Kimley-Horn and Associates, Inc.
Dallas, TX 75240
E-B.5 (972-770-1300 Alex Rathbun)
27'-3 3/4"
LANDSCAPE ARCHITECT
20
14/S610A-OF 1/S630-OF 2" E.J. LEVEL 05 SWA Group
S611-OF 2001 Irving Boulevard, Suite 157
3" E.J. LEVEL 07
WB-1 Dallas, TX 75207
E-C
STRUCTURAL
7'-1"
Datum Engineers
A Dallas, TX 75235

E-2
19'-3"
ME Engineers, Inc.
SW-3
STAIR 1 AHU
SW-1
5,000# Dallas, TX 75207
ELEV. PE1 STAIR 2
A8 SEE LEVEL 03 (S203-OF)
FOR ADDN'L INFO. NOT ELEVATOR CONSULTANT
B SHOWN AT INFILL, TYP. Persohn | Hahn Associates, Inc.
E-4 SW-2 McKinney, TX 75071
INTERIOR DESIGNER
Rottet Studio
FLOOR DESIGNED FOR ONE 808 Travis Street, Suite 100
30'-7 1/4"
FUTURE INTERFLOOR STAIR ON Houston, TX 77002

EITHER SIDE OF BRIDGE. (713-221-1830 x 6105 Anja Majkic)
P DL = 6k, P LL = 6k
14/S610A-OF
T.O.S.C. EL. = 521'-2" 14/S610A-OF
E-7
214-358-0174 512-469-9490 210-858-2880

DATE ISSUE TITLE
E-D CURTAIN WALL

2" E.J. LEVEL 05 SEE ARCH'L 1 2" E.J. LEVEL 05 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
3" E.J. LEVEL 07 S221-OF 3" E.J. LEVEL 07 10/30/2020 ISSUE FOR PERMIT
2'-2" 12/18/2020 90% CONSTRUCTION DOCUMENTS


TYPICAL SECTIONS AND RESERVED FOR REVIEWERS NOTES
6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 19'-4" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
S203A-OF FOR DIMENSION
CONTROL AND REINFORCING
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"
1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 LEVELS 05 FRAMING PLAN .05 12/18/2020 Permit Set Update
3/32" = 1'-0"
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
(David Leff)
Dallas, TX 75202
CONTRACTOR SHALL VERIFY EXISTING S220-OF
ENGINEER. THIS WORK IS TO BE C
CONTRACTOR SHALL VERIFY EXISTING GFF Architects
PERFORMED PRIOR TO TERRACE LEVEL COLUMN SIZE AND REINF. AND REPORT TO 2808 Fairmount St., Suite 300
PLATFORM WORK. COLUMN BEEF UP MAY ENGINEER. THIS WORK IS TO BE Dallas, TX 75201
BE REQUIRED IN THESE LOCATIONS. PERFORMED PRIOR TO TERRACE LEVEL (214-303-1500 Michael Reyes)
CONTRACTOR CARRY CONTINGENCY, PLATFORM WORK. COLUMN BEEF UP MAY
SEE 14 AND 20/610A-OF . BE REQUIRED IN THESE LOCATIONS. ZONING/ENTITLEMENT
13'-11 1/2"
GEOTECH
ECS Southwest, LLP
15/S610A-OF 15/S610A-OF 3033 Kellyway Drive, Suite 110
E-B CIVIL ENGINEER
15/S610A-OF
Dallas, TX 75240
E-B.5 (972-770-1300 Alex Rathbun)
C
27'-3 3/4"
COLUMN SIZE AND REINF. AND REPORT TO LANDSCAPE ARCHITECT

15/S610A-OF 1/S630-OF ENGINEER. THIS WORK IS TO BE SWA Group
Dallas, TX 75207
E-C BE REQUIRED IN THESE LOCATIONS.
7'-1"
SEE 14 AND 20/610A-OF

Datum Engineers
A Dallas, TX 75235
STAIR 2 MEP ENGINEER

E-2
19'-3"
ME Engineers, Inc.
SW-3
STAIR 1 1825 Market Center Blvd., Suite 600
SW-1 Dallas, TX 75207

A8
ELEVATOR CONSULTANT
B Persohn | Hahn Associates, Inc.
E-4 SW-2 McKinney, TX 75071
BEAM DESIGNED FOR ONE FUTURE (972-832-4232 Tom Williams)
INTERFLOOR STAIR ON EITHER
SIDE OF BRIDGE. INTERIOR DESIGNER
P DL = 6k, P LL = 6k Rottet Studio
30'-7 1/4"
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
15/S610A-OF
15/S610A-OF
E-7
C
CONTRACTOR SHALL VERIFY EXISTING www.datumengineers.com | Co. Reg. No. F-2819
DATE ISSUE TITLE
E-D CURTAIN WALL CONTRACTOR CARRY CONTINGENCY,

2'-2" 6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 19'-4" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4"
SEE 14 AND 20/610A-OF .
TYPICAL SECTIONS,
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4" DIMENSION CONTROL
AND REINFORCING
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 LEVEL 06 REV. DATE ISSUE TITLE

3/32" = 1'-0" .05 12/18/2020 Permit Set Update
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
(David Leff)
Dallas, TX 75202
S220-OF
CONTRACTOR SHALL VERIFY EXISTING CONTRACTOR
C SHALL VERIFY EXISTING GFF Architects
COLUMN SIZE AND REINF. AND REPORT TO COLUMN SIZE AND REINF. AND REPORT TO 2808 Fairmount St., Suite 300
ENGINEER. THIS WORK IS TO BE Dallas, TX 75201
PERFORMED PRIOR TO TERRACE LEVEL PERFORMED PRIOR TO TERRACE LEVEL
PLATFORM WORK. COLUMN BEEF UP MAY PLATFORM WORK. COLUMN BEEF UP MAY
BE REQUIRED IN THESE LOCATIONS. BE REQUIRED IN THESE LOCATIONS. ZONING/ENTITLEMENT
CONTRACTOR CARRY CONTINGENCY, CONTRACTOR CARRY CONTINGENCY, Baldwin Associates
SEE 14 AND 20/610A-OF . Dallas, TX 75226
E-A (214-824-7949 Robert Baldwin)
SEE LEVEL 03 (S203-OF)

13'-11 1/2"
GEOTECH
FOR ADDN'L INFO. NOT
ECS Southwest, LLP
SHOWN AT INFILL, TYP.
E-B CIVIL ENGINEER

Dallas, TX 75240
(972-770-1300 Alex Rathbun)
E-B.5
C
27'-3 3/4"
LANDSCAPE ARCHITECT
SWA Group
1/S630-OF ENGINEER. THIS WORK IS TO BE 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
E-C BE REQUIRED IN THESE LOCATIONS.
7'-1"
SEE 14 AND 20/610A-OF Datum Engineers

A Dallas, TX 75235
1'-3"
MEP ENGINEER
STAIR 2
E-2 ME Engineers, Inc.
19'-3"
STAIR 1
SW-3
AHU 1825 Market Center Blvd., Suite 600
SW-1
5,400# Dallas, TX 75207
T.O.S. EL. = 549'-2" T.O.S.C. EL. = 541'-2" (214-741-1589 Drew Shivley)
A8 SEE LEVEL 03 (S203-OF)
FOR ADDN'L INFO. NOT ELEVATOR CONSULTANT
B SHOWN AT INFILL, TYP. Persohn | Hahn Associates, Inc.
E-4 SW-2 HSS6X6X1/2 GUIDE
McKinney, TX 75071
RAIL POST, TYP.
SEE 10/S304-OF INTERIOR DESIGNER
Rottet Studio
30'-7 1/4"
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
E-7
C Dallas Austin San Antonio

Datum Project No.
DATE
19166
ISSUE TITLE
PLATFORM WORK. COLUMN BEEF UP MAY 04/03/2020 SCHEMATIC DESIGN PRESENTATION
E-D CONTRACTOR CARRY CONTINGENCY,
05/06/2020
07/22/2020
ISSUE FOR SCHEMATIC DESIGN
SEE 14 AND 20/610A-OF 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
CONTRACTOR SHALL VERIFY EXISTING 12/18/2020 90% CONSTRUCTION DOCUMENTS
COLUMN SIZE AND REINF. AND REPORT TO 2'-2"

SEE 14 AND 20/610A-OF . 6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 19'-4" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" SEE SHEET S203-OF FOR
TYPICAL SECTIONS AND
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"
S203A-OF FOR DIMENSION
1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 LEVEL 07
3/32" = 1'-0"
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

E-0 E-0.4E-0.6
(David Leff)
Dallas, TX 75202
S220-OF
GFF Architects
SEE SHEET S620-OF FOR Dallas, TX 75201
10
TERRACE FRAMING INFO.
2 ZONING/ENTITLEMENT
S621-OF S621-OF Baldwin Associates
Dallas, TX 75226
E-A 7 (214-824-7949 Robert Baldwin)
S622-OF
13'-11 1/2"
5 GEOTECH
2 ECS Southwest, LLP
12 S623-OF
S623-OF 3033 Kellyway Drive, Suite 110
S621-OF Carrollton, TX 75006
E-B CIVIL ENGINEER

8 Kimley-Horn and Associates, Inc.
7 S623-OF 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
S623-OF (972-770-1300 Alex Rathbun)
E-B.5 16
27'-3 3/4"
S411-OF LANDSCAPE ARCHITECT

SWA Group
1/S630-OF 2001 Irving Boulevard, Suite 157
WB-1 Dallas, TX 75207
E-C 1'-10" 1'-0" STRUCTURAL
7'-1"
PTB801 PTB802 PTB803 PTB809 PTB802 O.H. PTB801 O.H.

17 Datum Engineers
9"
A 17
S411-OF Dallas, TX 75235
1'-3"
S411-OF (214-358-0174 Rodolfo D'Arlach)
9'-5"
2'-4"
8 C12, F/S401-OF C12, F/S401-OF
2'-0"
S621-OF ELEV. SE1 ELEV. PE2 T.O.S.C. EL. = 557'-2" MEP ENGINEER
E-2 E-2 ME Engineers, Inc.
15/S622-OF
19'-3"
SW-3
STAIR 1 AHU 1825 Market Center Blvd., Suite 600
SW-1
8,000 STAIR 2 EXISTING STAIR Dallas, TX 75207
T.O.S. EL. = 565'-2" TOWER TO BE (214-741-1589 Drew Shivley)
9/S304-OF
A8 C12, F/S401-OF
ELEV. PE1 DEMO'D
PTB804 PTB805 PTB806 PTB810 PTB805 O.H. PTB804 O.H. 17 ELEVATOR CONSULTANT
B 17 S411-OF Persohn | Hahn Associates, Inc.
5"
S411-OF SW-2 HSS6X6X1/2 GUIDE C12, F/S401-OF

16 E-4 McKinney, TX 75071
E-4 RAIL POST, TYP. S411-OF
SEE 10/S304-OF 9'-5"
INTERIOR DESIGNER
Rottet Studio
30'-7 1/4"
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
E-7 C12, F/S401-OF

5 E-7
16 S621-OF
C12, F/S401-OF www.datumengineers.com | Co. Reg. No. F-2819
S411-OF
PTB807 PTB808 PTB808 O.H. PTB807 O.H. Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
17
C 17 S411-OF
C Datum Project No.
DATE
19166
ISSUE TITLE
S411-OF
2'-6"
2'-6"
E-D CURTAIN WALL E-D 05/06/2020

07/22/2020
ISSUE FOR SCHEMATIC DESIGN
SEE ARCH'L
18 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
18
S411-OF 10/30/2020 ISSUE FOR PERMIT
S411-OF 12/18/2020 90% CONSTRUCTION DOCUMENTS
6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" 2'-4"
TYPICAL SECTIONS AND
13'-8" 30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 13'-8" S209A-OF FOR DIMENSION
00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 LEVEL 08
3/32" = 1'-0"
NOTE TO CONTRACTOR:

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

(David Leff)
Dallas, TX 75202
GFF Architects
Dallas, TX 75201
21'-1 1/2" (214-303-1500 Michael Reyes)
21'-1 1/2"
ZONING/ENTITLEMENT
Baldwin Associates
Dallas, TX 75226
2'-3"
9'-5" GEOTECH
9C15
1'-10"
S6
S6
PTB901 PTB902 PTB903 PTB909 PTB902 O.H. PTB901 O.H. ECS Southwest, LLP
9" 3033 Kellyway Drive, Suite 110
A
CIVIL ENGINEER
1'-3"
2'-4"
9"
4'-4"
6'-0" 9C10 6'-0" 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
ELEV. PE2
ELEV. SE1
6" 6" 11'-3 1/8" LANDSCAPE ARCHITECT
11'-3 1/8" T.O.S.C. EL. = 573'-2" SWA Group
S1

18'-6"
STAIR 2 Dallas, TX 75207
9C14
S1
S1
S1
9M10 (214-954-0016 Chuck McDaniel)
STAIR 1
STRUCTURAL
T.O.S. EL. = 581'-2"
Datum Engineers
ELEV. PE1 Dallas, TX 75235
9C18A
A8
9"
9C16A 9C17A MEP ENGINEER

PTB904 PTB905 PTB906 PTB910 PTB905 O.H. PTB904 O.H. ME Engineers, Inc.
B 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
6'-0"
HSS6X6X1/2 GUIDE 9C16B 9'-5" 9C18B 9C8 9C9 ELEVATOR CONSULTANT

9C5 9C6 9C7 RAIL POST, TYP. Persohn | Hahn Associates, Inc.
SEE 10/S304-OF 9C17B
McKinney, TX 75071
9M8 9M9 INTERIOR DESIGNER

Rottet Studio
9M6 9M7 808 Travis Street, Suite 100
9M5 Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
SM18
SM20
9C13
9C12
9C11
SM20
SM18
9C11
9C12

9M2 SEE S203A-OF FOR 9M3 9M4 214-358-0174 512-469-9490 210-858-2880
8'-0"
ADDN'L INFO. NOT SHOWN Datum Project No. 19166

DATE ISSUE TITLE
9M1
9C1 9C2 9C3 9C4
7'-0"

PTB907 PTB908 B901 B901 B902 PTB908 O.H. PTB907 O.H.
C RESERVED FOR REVIEWERS NOTES
5'-0" 5'-0" 2'-6" 2'-6" 5'-0" 4'-6" 5'-0" 5'-0" 6'-0" 6'-0" 6'-0" 6'-0" 6'-0" 2'-6" 5'-0" 5'-0"
CURTAIN WALL 6"
1'-3" SEE ARCH'L

00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 LEVEL 09 SLAB REINFORCING

3/16" = 1'-0"

3001 MAPLE AVENUE
2. SEE SHEET S101-OF FOR TYPICAL PLAN NOTES, SYMBOLS, ABBREVIATIONS AND
LEVEL 09 SLAB REINFORCING

190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

(David Leff)
Dallas, TX 75202
22'-10 1/4" 22'-10 1/4"
GFF Architects
Dallas, TX 75201
1
ZONING/ENTITLEMENT
S220-OF
Baldwin Associates
7 9 Dallas, TX 75226
ROOF TERRACE CANOPY
S622-OF S622-OF (214-824-7949 Robert Baldwin)
C6X13 GEOTECH
ECS Southwest, LLP
7'-0"
C6X13 TYP.
10
HSS20X12X1/2 (LLV) (972-392-3222 Siddharth Neekhra)
E-B S622-OF
CIVIL ENGINEER
7'-0"
C6X13 Dallas, TX 75240
E-B.5 (972-770-1300 Alex Rathbun)
11 12 13
11 LANDSCAPE ARCHITECT
S411-OF S411-OF S411-OF SWA Group
S411-OF 21'-1 1/2"
21'-1 1/2" 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
2'-3"
STRUCTURAL
5'-10"
20
S412-OF Datum Engineers
A 20 A 6516 Forest Park Road
1'-3"
Dallas, TX 75235
6'-0"
4'-4"
9"
S412-OF 6'-0" 9'-5" (214-358-0174 Rodolfo D'Arlach)
10
11'-3 1/8" 6" ELEV. SE1 ELEV. PE2 T.O.S.C. EL. = 573'-2" 6" 11'-3 1/8" S411-OF MEP ENGINEER
18'-6"
SW-3
19'-3"
STAIR 1 AHU STAIR 2 ME Engineers, Inc.
SW-1
T.O.S. EL. = 581'-2" 8,000 Dallas, TX 75207
9/S304-OF
A8 ELEV. PE1 A8 (214-741-1589 Drew Shivley)
9"
5"
20 ELEVATOR CONSULTANT
B 15 S412-OF B Persohn | Hahn Associates, Inc.
S412-OF
McKinney, TX 75071
20'-0" SW-2 2 20'-0" (972-832-4232 Tom Williams)
S503-OF 9'-5"
14 HSS6X6X1/2 GUIDE 14
INTERIOR DESIGNER
S411-OF RAIL POST, TYP. Rottet Studio
S411-OF 808 Travis Street, Suite 100
SEE 10/S304-OF
30'-7 1/4"
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
10
S411-OF Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
15
C 10 S412-OF
DATE ISSUE TITLE
1'-8"
S412-OF
CURTAIN WALL 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SEE ARCH'L 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT

1. SEE SHEET S203-OF FOR 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
TYPICAL SECTIONS AND 10/30/2020

12/18/2020
ISSUE FOR PERMIT
90% CONSTRUCTION DOCUMENTS
S203A-OF FOR DIMENSION 01/25/2021 100% CONSTRUCTION DOCUMENTS
CONTROL.
2. SEE S209A-OF FOR BEAM RESERVED FOR REVIEWERS NOTES
1'-1 1/2" 13'-8" 6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 19'-4" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" 13'-8" 1'-1 1/2" MARKS, SLAB MARKS AND
DIMENSION CONTROL FOR
30'-0" 30'-0" 30'-0" 30'-0" 30'-0" NEW OFFICE FLOORPLATE
00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 LEVEL 09
3/32" = 1'-0"

3001 MAPLE AVENUE
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201

Houston, TX 77056
EQUITY PARTNERS
McNair Interests
Houston, TX 77024
(Drew Steffen)

(David Leff)
Dallas, TX 75202
GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
RM25
RS3
RC28
RC31
RM28
RM31
RC34
RC37
RS3
Baldwin Associates
Dallas, TX 75226
BR05 BR06 BR07 BR09 BR10 (214-824-7949 Robert Baldwin)
A RC15
RC16 GEOTECH
BR08 RC17 RC18 ECS Southwest, LLP
1'-7"
RS2
6'-0"
RC14
4'-6" 3033 Kellyway Drive, Suite 110
BR23
BR16
BR13
BR14
BR17
CIVIL ENGINEER
RM16 RM17 Kimley-Horn and Associates, Inc.
BR18
RM27
Dallas, TX 75240
RC33
RC30
RM30
RM33
RM35
SW-3
RC36
RC39
RC20
RM24
RS1
RC27
RM18
RC20
RC22
RS1
RS1
RM14 RM15
1'-0"
SW-1
LANDSCAPE ARCHITECT
BR24
BR15
SWA Group
BR23
RS2 Dallas, TX 75207
RC12A RC13A (214-954-0016 Chuck McDaniel)
6'-0"
A8 RC9 RC11 STRUCTURAL
BR02 BR03 RC10
Datum Engineers
B BR01 BR04 13/S413-OF BR11 BR12
Dallas, TX 75235
6'-0"
RC8
RC5 RC6 RC7 MEP ENGINEER
RC12B RC13B
ME Engineers, Inc.
Dallas, TX 75207
SW-2 (214-741-1589 Drew Shivley)
RM10 RM11 RM12 RM13 ELEVATOR CONSULTANT

Persohn | Hahn Associates, Inc.
9 INCH. THICK
RC19
RM6 RM8 RM9 8612 Broad Meadow Lane

RM5 RM7 DROP PANEL. TYP. McKinney, TX 75071
INTERIOR DESIGNER
Rottet Studio
RM2 Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
RM26
RM29
RM32
RC32
RC35
RM34
RC38
RM22
RM19
RM20
RM21
RM22A
RC25
RM2
RC21
RC23
RM23
RC26
RC29
@OPENING
RM1 RM2 RM2
RC19
8'-0"
RM3 RM4
ADDN'L 6#5X10'-0"
W/ STANDARD HOOKS AT www.datumengineers.com | Co. Reg. No. F-2819
8" O.C. WHERE SHOWN Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880

RC1 RC2 RC2 RC3 RC4 DATE ISSUE TITLE
RC2 RC2
7'-0"

BR19 BR20 BR21 BR21 BR22 BR20 BR19 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
C 10/30/2020 ISSUE FOR PERMIT
5'-0" 5'-0" 2'-6" 2'-6" 5'-0" 4'-6" 5'-0" 5'-0" 6'-0" 6'-0" 6'-0" 6'-0" 6'-0" 2'-6" 6'-0"
1'-3" 1'-6"
5'-0"
00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 ROOF - REINFORCING
3/16" = 1'-0"
PLAN NOTES:
MAPLE TERRACE
3001 MAPLE AVENUE
1. NORTH ARROW
2. SEE SHEET S101-OF FOR TYPICAL PLAN NOTES, SYMBOLS, ABBREVIATIONS AND LEVEL ROOF SLAB
REINFORCING
190013
PROJECT NUMBER
4 5 6 7 NOTE: 5 6 8 11
SEE 2/S210-OF FOR
MACHINE ROOM 23'-10"
5'-8" 23'-10" 6" FRAMING PLAN.
NOTE: 61'-7"
T.O.S.C. EL. = 588'-5 1/2" 1 COORDINATE WITH FINAL T.O.S.C. EL. = 596'-4"
TYP. S412-OF ELEVATOR CUTSHEETS C/S405-OF, TYP.
@ CORNERS DEVELOPER
8,700# TYP. 3,600# ELEVATOR 2 TYP. T.O.S. EL. = 601-5"
HSS6X6X1/4 TYP. AT Hines
SHAFT BELOW TYP.
1'-1" TYP.
S412-OF
MACHINE BEAMS PER 1,600# MACHINE BEAMS PER SCREEN WALL 2200 Ross Avenue, Suite 4200W
ELEVATOR MFR., TYP. W8X21 ELEVATOR SHAFT (T.O.S. EL. = 601'-5") Dallas, TX 75201
ELEVATOR MFR., TYP. (972-716-2908 Corbin Eckel)
12/S413-OF BELOW
14,000# 2800 Post Oak Blvd., 49th Floor
A 4,600# A Houston, TX 77056
HSS12X6X1/4 (LLV)
HSS12X6X1/4 (LLV)
14/S413-OF
HSS12X6X1/4 (LLV)
1 W8X21,SEE (713-621-8000 Juan Delgado)
17/S413-OF
EQ
S412-OF 15/S413-OF TYP.
ELEV. PE2 8,000#
HSS12X6X3/8 (LLV)
ELEV. SE1 6,700# HSS12X6X1/4 (LLV) EQUITY PARTNERS
TYP.
13/S413-OF
19'-3"
19'-3"
HSS12X6X3/8 (LLV)
HSS12X6X3/8 (LLV)
McNair Interests
13/S413-OF
TYP.
24'-8 1/2"
4,600# 109 N. Post Oak Lane, Suite 600
SLOPE
EQ
1,600# 14,000# Houston, TX 77024
ELEV. PE1 17/S413-OF (Drew Steffen)
18,200# 8,000# HSS12X6X1/4 (LLV)
6,700# Mitsui Fudosan America
6,400# TYP. 1251 Avenue of the Americas, Suite 800
SLAB REINF.:
B B New York, New York 10020
EQ
13/S413-OF
#5@12" O.C. TOP 15/S413-OF 13/S413-OF
(David Leff)
AND BOT. EA. WAY TYP.
SW-2 OFFICE/RETAIL ARCHITECT
1'-8" 1217 Main St., Suite 500
T.O.S.C. EL. = 596'-9 1/2" HSS6X6X1/4 TYP. AT Dallas, TX 75202
1 1/2" SCREEN WALL (214-347-4982 Christine Robbins-Elrod)
HSS6X6X1/4 AT TOP OF PERFORATED METAL
EQ EQ (T.O.S. EL. = 601'-5")
SCREEN OPENING. SCREEN WALL SEE 11/S413-OF MASTER/MULTIFAMILY ARCHITECT
(T.O.S. EL. = 597'-4") AND ARCH'L GFF Architects
Dallas, TX 75201
2 MACHINE ROOM BEAM SUPPORT FRAMING 3 ELEVATOR PENTHOUSE ROOF ZONING/ENTITLEMENT

3/32" = 1'-0" 3/32" = 1'-0" Baldwin Associates
Dallas, TX 75226
GEOTECH
ECS Southwest, LLP
CIVIL ENGINEER
Dallas, TX 75240
LANDSCAPE ARCHITECT
SWA Group
Dallas, TX 75207
T.O.S.C. EL. = 587'-6 3/8"
HSS6X6X1/4 TYP. AT
STRUCTURAL
1 SCREEN WALL Datum Engineers
S220-OF (T.O.S. EL. = 590'-8") Dallas, TX 75235
4 1'-8" 2'-8" 8'-9 1/2" 2'-7 1/2" 1 1/2" 4
S413-OF 1 4 S413-OF 19'-0 1/2" MEP ENGINEER
DAVIT ROOF DRAIN 10 ROOF DRAIN DAVIT
S412-OF S413-OF SEE 8/S413-OF ME Engineers, Inc.
SEE 8/S413-OF SEE ARCH'L S413-OF SEE ARCH'L
E-C E-C Dallas, TX 75207
1'-10"
5'-8 3/4"
3 1/4"
C13,F/S401-OF (214-741-1589 Drew Shivley)
7'-1"
ELEVATOR CONSULTANT
A 3
A
13/S413-OF
S413-OF
2'-2"
C13, F/S401-OF 8612 Broad Meadow Lane
EQ
McKinney, TX 75071
E-2 E-2
1'-0"
SW-3
19'-3"
13/S413-OF
1/4" X 3" STRAP INTERIOR DESIGNER
24'-8 1/2"
24'-8 1/2"
SW-1
ROOF ANCHOR PLATES RTU
EQ
Rottet Studio
SEE 9/S413-OF 23,000#
A8 6
C13, F/S401-OF 9/S304-OF ROOF HATCH 6 A8 808 Travis Street, Suite 100
Houston, TX 77002
OPENING S503-OF (713-221-1830 x 6105 Anja Majkic)
S503-OF SEE ARCH'L
B 3 B
5'-2 1/4"
EQ
13/S413-OF 13/S413-OF
S413-OF C13,F/S401-OF 1/4" X 3" STRAP PLATES 2
62'-9"
E-4 SW-2 S413-OF

E-4
6
3
1'-8" 1 1/2" www.datumengineers.com | Co. Reg. No. F-2819
1/4" X 3" STRAP PLATES S413-OF
1 1/2" S503-OF 6'-6" 6'-9" 6'-9" 8 EQ. SPACES = 61'-7" PERFORATED METAL Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
SCREEN WALL SEE 11/S413-OF Datum Project No. 19166
30'-7 1/4"
AND ARCH'L
2'-6" DATE ISSUE TITLE
EQ EQ HSS6X6X1/4 TYP. AT W8X21, TYP. 04/03/2020 SCHEMATIC DESIGN PRESENTATION
SCREEN WALL ALONG SCREEN
14'-0 1/2" (T.O.S. EL. = 590'-8")
SLOPE
E-7 E-7 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
J/S401-OF 10/30/2020 ISSUE FOR PERMIT
2 TYP. 12/18/2020 90% CONSTRUCTION DOCUMENTS
S413-OF 01/25/2021 100% CONSTRUCTION DOCUMENTS
C C
1'-8"
E-D E-D
1
S413-OF
T.O.S.C. EL. = 588'-8 3/4"
13'-8" 6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 30'-0" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" 13'-8"
6" 6"
1'-0 1/2" 1'-0 1/2"
30'-0" 30'-0" 30'-0" 30'-0" 30'-0"
00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 ROOF
3/32" = 1'-0"

3001 MAPLE AVENUE
2. SEE SHEET S101-OF FOR TYPICAL PLAN NOTES, SYMBOLS, ABBREVIATIONS AND LEVEL ROOF FRAMING PLAN
190013
PROJECT NUMBER
DEVELOPER
Hines
Dallas, TX 75201
E-A E-B E-B.5 E-C A B C
Houston, TX 77056
SEE PLAN SEE PLAN SEE PLAN (713-621-8000 Juan Delgado)
SCREEN TOS
601'-5" EQUITY PARTNERS
McNair Interests
10 109 N. Post Oak Lane, Suite 600
S413-OF Houston, TX 77024
(Drew Steffen)
T.O.S.C. EL,
SEE PLAN Mitsui Fudosan America
T.O.S.C. EL, 1251 Avenue of the Americas, Suite 800
SEE PLAN New York, New York 10020
ROOF (David Leff)
589'-2"
Dallas, TX 75202
15'-3"
GFF Architects
Dallas, TX 75201
LEVEL 09 (214-303-1500 Michael Reyes)
573'-2"
ZONING/ENTITLEMENT
Baldwin Associates
Dallas, TX 75226
16'-0"
GEOTECH
ECS Southwest, LLP
LEVEL 08 (972-392-3222 Siddharth Neekhra)
557'-2"
CIVIL ENGINEER
EXIST. ROOF 13455 Noel Road, Two Galleria Office Tower, Suite 700
551'-2" Dallas, TX 75240
1
EXIST. BUILDING LANDSCAPE ARCHITECT
S221-OF
26'-0"
SWA Group
Dallas, TX 75207
LEVEL 07 (214-954-0016 Chuck McDaniel)
541'-2"
STRUCTURAL
Datum Engineers
107'-3"

Dallas, TX 75235
LEVEL 06
531'-2" MEP ENGINEER
ME Engineers, Inc.
10'-0"
Dallas, TX 75207
ELEVATOR CONSULTANT
LEVEL 05
521'-2" 8612 Broad Meadow Lane
McKinney, TX 75071
10'-0"
INTERIOR DESIGNER
Rottet Studio
LEVEL 04 808 Travis Street, Suite 100
511'-2" Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
10'-0"
CANOPY
SEE ARCH'L
LEVEL 03 www.datumengineers.com | Co. Reg. No. F-2819
501'-2" Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880

10'-0"
DATE ISSUE TITLE

LEVEL 02 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
491'-2" 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT

SEE SHEET S610-OF FOR 12/18/2020 90% CONSTRUCTION DOCUMENTS
10'-0"
ADDITIONAL INFO. TEMP.

BRACING BY SITEWORK 01/25/2021 100% CONSTRUCTION DOCUMENTS
GENERAL SEE CIVIL/LANDSCAPE

16 CONTRACTOR
LEVEL 01 RESERVED FOR REVIEWERS NOTES
S307-OF
481'-2"
FAT CLAY = 100'-0"
SEE GARAGE DRAWINGS

FOR RETENTION SYSTEM
AND GARAGE WALLS
LEVEL B1
471'-0"
LEAN CLAY
+/- 36'-6"
LEVEL B2
EXIST. FOOTING 461'-8" REV. DATE ISSUE TITLE
FOUNDATIONS .05 12/18/2020 Permit Set Update
CLAYEY SAND
LEVEL B3
452'-4"
WEATHERED LIMESTONE
GREY LIMESTONE
1 BUILDING ELEVATION
1/8" = 1'-0"
MAPLE TERRACE
3001 MAPLE AVENUE
BUILDING SECTIONS
190013
PROJECT NUMBER
SEE PLAN SEE PLAN SEE PLAN SEE PLAN SEE PLAN DEVELOPER
Hines
14 2200 Ross Avenue, Suite 4200W
S410-OF EXIST. CLAY TILE EXISTING FINISH Dallas, TX 75201
TO BE DEMO'D TO REMAIN (972-716-2908 Corbin Eckel)
1
S410-OF 2800 Post Oak Blvd., 49th Floor
10" THICK SLAB EXIST. STRUCTURE Houston, TX 77056
8" THICK SLAB, (713-621-8000 Juan Delgado)
SEE PLAN SEE PLAN E.J.
T.O. EXIST. EL. EQUITY PARTNERS
SEE PLAN McNair Interests
Houston, TX 77024
(Drew Steffen)

DROP PANEL BEYOND FIREPROOF TO (David Leff)
DROP PANEL BEYOND SEE PLAN MEET 2 HR RATING
SEE PLAN
10'-0" (F.V.)
CONCRETE BEAM 1217 Main St., Suite 500
SEE PLAN Dallas, TX 75202
COLUMN BEYOND EXIST. CLAY TILE
SEE PLAN TO BE DEMO'D 2 MASTER/MULTIFAMILY ARCHITECT
COLUMN BEYOND GFF Architects
S613-OF
SEE PLAN 2808 Fairmount St., Suite 300
8" THICK SLAB Dallas, TX 75201
EXIST. STRUCTURE TYP. (214-303-1500 Michael Reyes)
SEE PLAN
COLUMN BEYOND
SEE PLAN T.O. EXIST. EL. ZONING/ENTITLEMENT
SEE PLAN Baldwin Associates
Dallas, TX 75226
GEOTECH
CONCRETE BEAM ECS Southwest, LLP
FIREPROOF TO 3033 Kellyway Drive, Suite 110
SEE PLAN MEET 2 HR RATING Carrollton, TX 75006
CURTAIN WALL BEAM BEYOND EXIST. 12X18 BEAM (F.V.), TYP. (972-392-3222 Siddharth Neekhra)
10'-0" (F.V.)
SEE ARCH'L SEE PLAN
CIVIL ENGINEER
EXIST. CLAY TILE 13455 Noel Road, Two Galleria Office Tower, Suite 700
TO BE DEMO'D Dallas, TX 75240
LANDSCAPE ARCHITECT
8" THICK SLAB, E.J. SWA Group
10" THICK SLAB SEE PLAN EXIST. STRUCTURE 2001 Irving Boulevard, Suite 157
T.O. EXIST. EL.
SEE PLAN STRUCTURAL
Datum Engineers
Dallas, TX 75235
FIREPROOF TO MEP ENGINEER

MEET 2 HR RATING ME Engineers, Inc.
Dallas, TX 75207
CONCRETE BEAM
SEE PLAN ELEVATOR CONSULTANT
McKinney, TX 75071
INTERIOR DESIGNER
1 BUILDING SECTION Rottet Studio
3/8" = 1'-0" 808 Travis Street, Suite 100
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
7 4 1 E1
SEE PLAN SEE PLAN SEE PLAN
SLAB ON VOID SLAB
SEE PLAN SEE PLAN E.J. Dallas Austin San Antonio
SEE PLAN 214-358-0174 512-469-9490 210-858-2880

LEVEL 01 DATE ISSUE TITLE
481'-2" 04/03/2020 SCHEMATIC DESIGN PRESENTATION
BEAM BEYOND
EXISTING 10/30/2020 ISSUE FOR PERMIT
SEE PLAN
BASEMENT WALL 12/18/2020 90% CONSTRUCTION DOCUMENTS
COLUMN BEYOND COLUMN BEYOND
SEE PLAN SEE PLAN
SLAB-ON-VOID
SEE PLAN RESERVED FOR REVIEWERS NOTES
SLAB E.J. P = 150K TO 275K
LEVEL B1 Level B1
471'-0"
5'-6" (F.V.)
TEMPORARY 3'-0"
RETENTION SYSTEM BASEMENT WALL
SEE PLAN
(F.V.)
BEAM BEYOND
1'-6"
TEMPORARY
SLAB RETENTION SYSTEM SEE PLAN
SEE PLAN REV. DATE ISSUE TITLE
7'-8" (F.V.) .05 12/18/2020 Permit Set Update
LEAN CLAY
LEVEL B2 Level B2
461'-8"
RETENTION
SYSTEM
CLAYEY SAND
SLAB-ON-GRADE
SEE PLAN
LEVEL B3 Level B3
452'-4"
WEATHERED
LIMESTONE
GREY LIMESTONE
MAPLE TERRACE
3001 MAPLE AVENUE
BUILDING SECTIONS
2 BUILDING SECTION
1/4" = 1'-0"
190013
PROJECT NUMBER
SLAB
SEE PLAN
E.J. SEE PLAN E.J. SEE PLAN
Level 2 Level 2
DEVELOPER
Hines
Dallas, TX 75201
SLAB-ON-VOID (972-716-2908 Corbin Eckel)
SEE PLAN
Houston, TX 77056
SLAB
SEE PLAN SLAB
TEMPORARY E.J. SEE PLAN E.J. SEE PLAN EQUITY PARTNERS
SEE PLAN
RETENTION SYSTEM McNair Interests
Level 1 Level 1 Houston, TX 77024
(Drew Steffen)

(David Leff)
SHEAR WALL
STAIR 7'-9" SEE PLAN OFFICE/RETAIL ARCHITECT
NOTE: Dallas, TX 75202
SLAB NOTE: SEE 3/S222-OF FOR
SEE PLAN SLAB-ON-GRADE SEE 3/S222-OF FOR (214-347-4982 Christine Robbins-Elrod)
SLAB INFO. NOT SHOWN.
SELECT FILL SEE PLAN INFO. NOT SHOWN.
SEE PLAN MASTER/MULTIFAMILY ARCHITECT
2"
GFF Architects
Level B1 Level B1 2808 Fairmount St., Suite 300
Dallas, TX 75201
3'-0"
BLIND SIDED
5'-6" (F.V.)
WATERPROOFING ZONING/ENTITLEMENT
MEMBRANE 3'-0" (F.V.) TEMPORARY Baldwin Associates
SHEAR WALL BY ARCHITECT RETENTION SYSTEM 3904 Elm Street, Suite B
SEE PLAN WATERPROOF Dallas, TX 75226
MEMBRANE (214-824-7949 Robert Baldwin)
SLAB BY ARCHITECT
SEE PLAN GEOTECH
LEAN CLAY SLAB
SEE PLAN ECS Southwest, LLP
LEAN CLAY 3033 Kellyway Drive, Suite 110
Level B2 Level B2 Carrollton, TX 75006
7'-8" X 8'-0" (F.V.) CIVIL ENGINEER

ELEVATOR Dallas, TX 75240
6" THICK SLAB ON

LANDSCAPE ARCHITECT
ELEVATOR ELEVATOR SLAB-ON-GRADE GRADE, SEE PLAN
SEE PLAN SWA Group
CLAYEY SAND CLAYEY SAND
RETENTION SYSTEM 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
Level B3 Level B3
STRUCTURAL
Datum Engineers
WEATHERED Dallas, TX 75235
WEATHERED
6'-6".
6'-6"
6'-6"
LIMESTONE (214-358-0174 Rodolfo D'Arlach)

LIMESTONE
MEP ENGINEER
ME Engineers, Inc.
Dallas, TX 75207
GREY LIMESTONE
GREY LIMESTONE
ELEVATOR CONSULTANT
SEE GEOTECHNICAL McKinney, TX 75071
REPORT (972-832-4232 Tom Williams)
INTERIOR DESIGNER
SEE GEOTECHNICAL
1 STAIR AND ELEVATOR CORE E-W 2 STAIR AND ELEVATOR CORE N-S REPORT
Rottet Studio
Houston, TX 77002
1/4" = 1'-0" 1/4" = 1'-0" (713-221-1830 x 6105 Anja Majkic)
8" STRUCTURED SLAB
SEE PLAN
E.J. SEE PLAN E.J. SEE PLAN
Level 1 Level 1
214-358-0174 512-469-9490 210-858-2880

6'-4" DATE ISSUE TITLE
5'-8" x 8'-0" (F.V.) 04/03/2020 SCHEMATIC DESIGN PRESENTATION

6'-4" 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SLAB-ON GRADE NOTE:
2'-0" (F.V.) P = 150K TO 250K
SEE 3/S222-OF FOR
INFO. NOT SHOWN.
FIELD VERIFY SIZE, DEPTH, 10/30/2020 ISSUE FOR PERMIT
THICKNESS AND LOCATION 12/18/2020 90% CONSTRUCTION DOCUMENTS
RETENTION SYSTEM BY
5" (F.V.)
OF EXIST. FOOTING PRIOR 01/25/2021 100% CONSTRUCTION DOCUMENTS

GENERAL CONTRACTOR
TO BEGINNING
(PERFORMANCE SPEC.)
5"
UNDERPINNING WORK.
Level B1 Level B1 RESERVED FOR REVIEWERS NOTES
(F.V.)
3'-0"
3'-0"
BACKFILL WITH
FLOWABLE FILL
(F.V.)
1'-6"
ELEVATOR
UNDERPINNING MICROPILES
WATERPROOFING BY UNDERPINNING CONTRACTOR
MEMBRANE (PERFORMANCE SPEC)
BY ARCHITECT
LEAN CLAY Level B2 LEAN CLAY Level B2

CLAYEY SAND CLAYEY SAND

COURSE AGGREGATE
Level B3 Level B3
COLLECTOR PIPE WEATHERED BOTTOM OF WEATHERED

6'-6"
SEE MEP LIMESTONE WALL BEYOND LIMESTONE
GREY LIMESTONE GREY LIMESTONE
PIER
SEE PLAN SEE GEOTECHNICAL
REPORT MAPLE TERRACE
3001 MAPLE AVENUE
BUILDING SECTIONS
3 RETENTION SYSTEM NORTH 4 RETENTION SYSTEM NORTH AT ELEVATOR

1/4" = 1'-0" 1/4" = 1'-0" 190013
PROJECT NUMBER
E.J.
C B.5 B 8" STRUCTURED SLAB A SEE PLAN E-C
Level 2
COLUMN BEYOND
SEE PLAN SEE PLAN SEE PLAN SEE PLAN SEE PLAN
SHEAR WALL
SEE PLAN DEVELOPER
Hines
E.J. 2200 Ross Avenue, Suite 4200W
SEE PLAN E.J. Dallas, TX 75201
SITEWORK SLAB (972-716-2908 Corbin Eckel)
SEE CIVIL/LANDSCAPE SEE PLAN SEE PLAN
Houston, TX 77056
Level 1 (713-621-8000 Juan Delgado)
EQUITY PARTNERS
McNair Interests
EXISTING 109 N. Post Oak Lane, Suite 600
BASEMENT WALL Houston, TX 77024
(Drew Steffen)
6'-4" Mitsui Fudosan America
SLAB New York, New York 10020
NOTE: (David Leff)
SLAB-ON-VOID SEE PLAN SEE 3/S222-OF FOR
SEE PLAN INFO. NOT SHOWN.
Level B1 1217 Main St., Suite 500
Dallas, TX 75202
GARAGE STRUCTURE
GFF Architects
SEE RESIDENTIAL TOWER 2808 Fairmount St., Suite 300
GARAGE DRAWINGS AND Dallas, TX 75201
RETENSION SYSTEM TEMPORARY RETENTION SYSTEM (214-303-1500 Michael Reyes)
PUMP HANDLE BEAM

ZONING/ENTITLEMENT
SEE PLAN Baldwin Associates
Dallas, TX 75226
Level B2 (214-824-7949 Robert Baldwin)
GEOTECH
ECS Southwest, LLP
RETENTION SYSTEM Carrollton, TX 75006
CIVIL ENGINEER
BASEMENT WALL
SEE PLAN Kimley-Horn and Associates, Inc.
Dallas, TX 75240
Level B3 LANDSCAPE ARCHITECT

SWA Group
Dallas, TX 75207
STRUCTURAL
Datum Engineers
Dallas, TX 75235
MEP ENGINEER
ME Engineers, Inc.
Dallas, TX 75207
ELEVATOR CONSULTANT
1 BUILDING SECTION McKinney, TX 75071

1/4" = 1'-0"
INTERIOR DESIGNER
Rottet Studio
E.J.
C B.5 B 8" FLAT PLATE A SEE PLAN
E-C Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
CONCRETE SLAB
Level 2
SEE PLAN SEE PLAN SEE PLAN SEE PLAN SEE PLAN www.datumengineers.com | Co. Reg. No. F-2819
214-358-0174 512-469-9490 210-858-2880

DATE ISSUE TITLE
E.J. 11 05/06/2020 ISSUE FOR SCHEMATIC DESIGN

SITEWORK SEE PLAN 8" THICK E.J.
8" THICK SLAB ON VOID SEE PLAN S601-OF
SEE CIVIL/LANDSCAPE SLAB ON VOID SEE PLAN 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
SEE PLAN 10/30/2020 ISSUE FOR PERMIT
Level 1 12/18/2020 90% CONSTRUCTION DOCUMENTS

EXISTING
BASEMENT WALL
WATERPROOF
MEMBRANE
BY ARCHITECT
Level B1

GARAGE STRUCTURE .05 12/18/2020 Permit Set Update
SEE RESIDENTIAL TOWER
GARAGE DRAWINGS AND
RETENSION SYSTEM
Level B2
Level B3
MAPLE TERRACE
3001 MAPLE AVENUE
BUILDING SECTION
2 BUILDING SECTION
1/4" = 1'-0" 190013
PROJECT NUMBER
T.O. WALL EL.
SEE ARCH'L.
SEE PLAN
12" BOND BEAM CHILLER

W/2#5 CONT. SEE MEP
FINISH
8
S230-OF
E-0 E-0.4 NOTE: SEE ARCH'L. DWL.-B @ 12"
W/ 1#4 X CONT. SLAB-ON-VOID
SEE CIVIL/LANDSCAPE SEE PLAN DEVELOPER
DROP IN GRADE 35'-4"
DRAWINGS FOR GRADING
BEAM EL. 10'-2" SPOT ELEVATIONS. Hines
SEE 17/S304-OF P/S301-OF T.O.S.C. EL. 2200 Ross Avenue, Suite 4200W
1'-0" (100'-0" = 481.17') Dallas, TX 75201
T.O.S.C. EL. SEE PLAN (972-716-2908 Corbin Eckel)
= 471.84' (90'-8")
8"
12" CMU WALL 2800 Post Oak Blvd., 49th Floor
T.O.S.C. EL. SEE GENERAL NOTES Houston, TX 77056
= 471.17' (90'-0") SITEWORK (713-621-8000 Juan Delgado)
SEE CIVIL MAX. HEIGHT (H) REINF.
15'-4" #7@24" EQUITY PARTNERS
19'-4 5/8"
P2, CC/S302-OF OFFICE MECHANICAL YARD McNair Interests
TYP. AT SCREEN WALL SEE ARCH'L 2'-4" (F.V.) 17'-4" #7@16" 109 N. Post Oak Lane, Suite 600
3'-0"
@ 15'-0" O.C. MAX. R= Houston, TX 77024
27 (Drew Steffen)
H
'-8 R= SEE PLAN
" Mitsui Fudosan America
4'-0"
3'-6"
DROP IN GRADE 1251 Avenue of the Americas, Suite 800

BEAM EL. New York, New York 10020
CHILLER
SEE 17/S304-OF (David Leff)
S17
S17
39,000# T.O. PIER EL.
SEE MEP
20/S601-OF
E-B DWL. TO MATCH SIZE
BEAM REINF:
3#9 TOP & BOT. 5G Studio Collaborative, LLC.
TYP.
& SPACING OF VERT. #4 STIR. @ 12" 1217 Main St., Suite 500
SLOPE
1/4"/FT
5 FIELD VERIFY EXTENTS WALL REINF. Dallas, TX 75202
SEE 12/S304-OF FOR SPLICE
32'-6"
OF EXISTING FOOTING (214-347-4982 Christine Robbins-Elrod)

S230-OF REQUIREMENTS.
S10
S10
E-B.5 PRIOR TO PIER DRILLING
OPERATIONS AND GRADE SITEWORK
2'-0" SEE 3/S304-OF FOR CORNER BARS
37'-2 1/2"
37'-8 1/4"
BEAM EXCAVATION, TYP. SEE CIVIL/LANDSCAPE GFF Architects

T.O.S.C. EL.
= 470.51' (89'-4") CHILLER 3/4" = 1'-0" 4 2808 Fairmount St., Suite 300
Dallas, TX 75201
30'-0"
39,000# COORDINATE TOP OF GRADE

S9
S9
78 BAR DIA. LAP

SEE MEP BEAM EL. WITH FINAL SITE PLAN
E-C ELEVATION AND FINAL WEST
RESTAURANT ELEVATION NOTE:
ZONING/ENTITLEMENT
SEE 4/S230-OF FOR Baldwin Associates
8 INFO. NOT SHOWN. Dallas, TX 75226
16" MAX.
P1, C/S302-OF TYP. (214-824-7949 Robert Baldwin)
S230-OF TYP. 4
41'-0" 3'-0"
S230-OF GEOTECH
T.O.S.C. EL.
E-2 SLAB-ON-VOID
5'-4" Carrollton, TX 75006
DROP IN GRADE SEE PLAN (972-392-3222 Siddharth Neekhra)
BEAM EL.
SEE 17/S304-OF CIVIL ENGINEER
23'-4"
BEAM REINF.: T.O.S.C. EL.
3'-0"
4#7 TOP & BOT.
A8 13455 Noel Road, Two Galleria Office Tower, Suite 700
8"
4 #4 STIR. @ 12" Dallas, TX 75240
4'-4" S306-OF 3#7 INTERM. E.F. (972-770-1300 Alex Rathbun)
18/S601-OF
T.O.S.C. EL.
= 469.84' (88'-8") LANDSCAPE ARCHITECT
SWA Group
T.O. PIER 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
8'-0"
3'-0"
78 BAR DIA. LAP
B.5 STRUCTURAL
PIER Datum Engineers
5'-4"
SEE PLAN 6516 Forest Park Road
Dallas, TX 75235
HOOKED DWLS. TO T.O. PIER EL.
MATCH VERT. PIER
REINF. MEP ENGINEER
ME Engineers, Inc.
1 MECHANICAL YARD PLAN 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
3/32" = 1'-0" (214-741-1589 Drew Shivley)
2'-0"
ELEVATOR CONSULTANT
3/4" = 1'-0" 8 Persohn | Hahn Associates, Inc.
2'-6"
3/4" = 1'-0" 5 8612 Broad Meadow Lane
McKinney, TX 75071
INTERIOR DESIGNER
Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)

214-358-0174 512-469-9490 210-858-2880

DATE ISSUE TITLE

MAPLE TERRACE
3001 MAPLE AVENUE
MECHANICAL YARD PLANS AND
DETAILS
190013
PROJECT NUMBER
FOUNDATION PROTECTION IN
PROVIDE SEAM PADS (HELD
SOIL RETAINER OPTIONS. SEE SPECS.
EXPANSIVE CLAY NOTES
IN PLACE WITH 8d NAILS) OR SOIL BARRIER MEMBRANE - 6" WIDE x 30# FELT
TAPE JOINTS TO PREVENT STRIP CONT. ALONG TOP OF RETAINER. LAP
CONCRETE FROM FLOWING FELT AT JOINTS & SEAL W/ MASTIC.
DUE TO THE EXPANSIVE CLAY SOILS THAT EXIST ON THIS SITE, CERTAIN CONSTRUCTION PRACTICES
INTO SMALL GAPS (TYP.) COMPLETELY COVER RETAINER JOINTS.
MUST BE FOLLOWED TO PREVENT DAMAGE TO THE FOUNDATIONS. THESE PROCEDURES ARE AS
FORM UP BOTTOM OF BEAM AND FOLLOWS:
REMOVE FORMS BEFORE BACKFILLING DEVELOPER
OR FORM VOID WITH CARTON FORMS. 1. IT IS THE CONTRACTOR'S RESPONSIBILITY TO MAINTAIN THE DEPTH OF VOID SPACE SHOWN Hines
SEPARATING THE CONCRETE FROM UNDERLYING EXPANSIVE CLAY. USE OF CARDBOARD CARTON 2200 Ross Avenue, Suite 4200W
GROUT Dallas, TX 75201
FORMS (VOID BOXES) IS THE INDUSTRY STANDARD PROCEDURE, BUT THE USE OF CARTON FORMS
3" TYP
AS A FORM MATERIAL IS THE CONTRACTOR'S OPTION. IF CARTON FORMS ARE USED INSTEAD OF (972-716-2908 Corbin Eckel)
STANDARD WOOD OR METAL FORMS, THE CONTRACTOR SHALL TAKE ALL NECESSARY PRECAUTIONS
NOTE: TO PREVENT ANY CRUSHING OR COLLAPSE OF CARTON FORMS WHICH WOULD RESULT IN A VOID Houston, TX 77056
SURE ROUND PIER VOID SPACE DEPTH LESS THAN THE DIMENSIONED DEPTH. (713-621-8000 Juan Delgado)
VOID DEPTH
SIZED TO FIT THE UPPER
SEE NOTES
PORTION OF DRILLED 1. FORM VOID SPACE WITH SOIL RETAINERS
UNDER ALL STRUCTURE CONCRETE PIER 2. THE BUILDING SITE MUST BE GRADED AWAY FROM THE BUILDING FOUNDATIONS IN THE INITIAL EQUITY PARTNERS
PIER VOID STAGE OF CONSTRUCTION. THE BUILDING PAD MUST BE MAINTAINED AT THE SPECIFIED MOISTURE
CAPS, PILASTERS, GRADE BEAMS, AND McNair Interests
WALLS BELOW GRADE. ALL STRUCTURAL CONTENT DURING CONSTRUCTION. STANDING PONDS OF WATER IN THE BUILDING FOUNDATION
CONCRETE (EXCEPT SLAB-ON-GRADE AREA WILL NOT BE ACCEPTABLE. Houston, TX 77024
SPECIFIED TO BE CAST ON EARTH) SHALL (Drew Steffen)
3" TYP.
BE SEPARATED FROM EXPANSIVE CLAY. 3. IT IS ESSENTIAL THAT BACKFILL AROUND ALL GRADE BEAMS BE PLACED IMMEDIATELY AFTER THE
GRADE BEAMS ARE CAST. IF RAIN OCCURS BEFORE THE BACKFILL IS PLACED, ALL OPEN Mitsui Fudosan America
EXCAVATIONS AROUND GRADE BEAMS MUST BE PUMPED DRY IMMEDIATELY AND KEPT DRY AT ALL 1251 Avenue of the Americas, Suite 800
2. CONTRACTOR SHALL PROTECT VOID
2"x6" PRECAST TIMES. BACKFILL AGAINST OUTSIDE FACE OF PERIMETER GRADE BEAMS WITH ON-SITE CLAY New York, New York 10020
END CAP, USE TO SEAL EXPOSED NOTE: BOXES AND PLACE CONCRETE IN A (David Leff)
ENDS, PREVENTING CONCRETE GRADE SHALL BE SMOOTH, EVEN, SPACER AT JOINTS MANNER TO PREVENT COLLAPSE OF THE MATERIALS, SEE P/S301-OF.
FROM FLOWING INTO END OF VOID LEVEL & DRY BEFORE INSTALLING OF RETAINERS VOID BOX. COLLAPSED VOID BOXES
4" to 6" 3" TYP. 4. ALL GRADE BEAMS AND OTHER ELEMENTS BELOW GRADE SHALL BE FORMED STRAIGHT AND TO THE OFFICE/RETAIL ARCHITECT
BOXES VOID BOXES. REFER TO VOID SHALL BE REPLACED PRIOR TO
LINES AND GRADES DETAILED. BACKFILL AS REQUIRED. DO NOT CAST SIDES AGAINST THE EARTH 5G Studio Collaborative, LLC.
DETAILS FOR APPLICATION. PLACEMENT OF ADDITIONAL CONCRETE. 1217 Main St., Suite 500
EXCAVATION. SEE B & P/S301-OF.
Dallas, TX 75202
RECTANGULAR VOID OPTION STRUCTURE OVER VOID (214-347-4982 Christine Robbins-Elrod)
WALL AND BEAM VOID 5. PROVIDE A VOID BETWEEN THE CLAY SOIL AND ALL STRUCTURAL CONCRETE PIER CAPS, PILASTERS,
TYPICAL DETAIL TYPICAL DETAIL GRADE BEAMS, WALLS AND SLABS WITHIN 10 FEET OF EXISTING GRADE WHICH ARE SUPPORTED ON
PIERS. ALL STRUCTURAL CONCRETE, EXCEPT SLAB- ON-GRADE, SHALL BE SEPARATED FROM
GFF Architects
NO SCALE
A NO SCALE
B EXPANSIVE CLAY. SEE A, B. F & L/S301-OF.
Dallas, TX 75201
6. IF CARTON FORMS ARE USED TO CONSTRUCT VOIDS, THEY MUST COMPLY WITH THE SPECIFICATIONS (214-303-1500 Michael Reyes)
AND THE FOLLOWING INSTALLATION PROCEDURES:
2'-0" COMPACTED
SURFACE TREATMENT (TOPSOIL,
PAVING, ETC.) SEE ARCHITECTURAL OR ZONING/ENTITLEMENT
2-FOOT THICKNESS OF WELL
CLAY CAP
CIVIL DRAWINGS FOR MATERIALS AND A. PAY SPECIAL ATTENTION TO THE PLACING OF CONCRETE, TO PREVENT CRUSHING THE CARTON Baldwin Associates
SLOPES COMPACTED, IMPERVIOS CLAY COVER BE FORMS UNDER THE DEAD WEIGHT OF THE CONCRETE.
PLACED OVER THE BACKFILL SURFACE TO 3904 Elm Street, Suite B
Dallas, TX 75226
1'-0".
MAX.
REDUCE INFILTRATION IN AREAS NOT B. PROTECT THE CARTON FORMS FROM DESTRUCTION DUE TO RAIN WATER AND REPLACE THE (214-824-7949 Robert Baldwin)
COVERED BY PAVEMENT. CARTON FORMS IF THEY BECOME SATURATED AND WEAK.
SPECIFIED VAPOR BARRIER
OVER PROTECTION BOARD GEOTECH
C. USE END CAPS TO CAP OFF THE DISCONTINUOUS ENDS OF CARTON FORMS AT CORNERS AND ECS Southwest, LLP
OVER CARTON FORMS
PIERS TO PREVENT SOIL OR CONCRETE FROM ENTERING VOID. SEE A/S301-OF. 3033 Kellyway Drive, Suite 110
SEE NOTES
D. BUTT CARTON FORMS INTO SIDES OF PIER. DO NOT LEAVE GAP BETWEEN FACE OF PIER AND (972-392-3222 Siddharth Neekhra)
DEPTH
VOID
CARTON FORM, BUT DO NOT ALLOW ANY PART OF CARTON FORM TO FALL WITHIN PIER
BASEMENT WALL CIRCUMFERENCE. END CAPS AT PIERS SHALL BE CIRCULAR. SEE A/S301-OF. CIVIL ENGINEER
(SEE ARCH'L. FOR
WATERPROOFING) E. JOIN CARTON FORMS TOGETHER TIGHTLY AT JOINTS AND COVER WITH SEAM PADS HELD IN 13455 Noel Road, Two Galleria Office Tower, Suite 700
PLACE WITH NAILS. DO NOT LEAVE GAPS BETWEEN UNITS. SEE A/S301-OF. Dallas, TX 75240
CONTROLLED F. PLACE CARTON FORMS ON SMOOTH, LEVEL SURFACE.
BACKFILL, LANDSCAPE ARCHITECT
CARTON FORMS SEE GENERAL G. DO NOT PUNCTURE CARTONS WITH BAR CHAIRS. USE SAND PLATES OR SUSPEND REINFORCING SWA Group
NOTES SLOPE CUT AS CAGES FROM THE TOP. 2001 Irving Boulevard, Suite 157
REQUIRED BY OSHA NOTE: Dallas, TX 75207
1. BACKFILL SHALL NOT BE PLACED AGAINST (214-954-0016 Chuck McDaniel)
THIS APPLIES TO LEVEL 1 ONLY, NOT REQUIRED AT LEVELS B1, B2 OR B3 LEVELS.
NOTE: FILTER FABRIC FOUNDATION WALL UNTIL ALL SUPPORTING SLABS,
REPLACE CARTON FORMS THAT HAVE BEEN DAMAGED OR BEAMS, STRUTS, ETC., HAVE ATTAINED THEIR 28-DAY STRUCTURAL
SEE SPECS.
IF THEY BECOME SATURATED AND WEAK. TAKE SPECIAL DESIGN STRENGTH, UNLESS PROPER BRACING IS 7. THE GRADE BEAMS SITUATED IN THE OVERBURDEN SOILS WITHIN 10 FEET BELOW EXISTING GRADES Datum Engineers
2'-0"
INSTALLED IN A MANNER APPROVED BY THE 6516 Forest Park Road
MIN.
CARE TO PREVENT CRUSHING OF CARTON FORMS SHOULD BE FORMED WITH NOMINAL 6-INCH VOID DEPTH WHERE SHOWN IN SHEET.
DURING PLACEMENT OF REINFORCING AND CONCRETE. ARCHITECT. Dallas, TX 75235
2. WHERE BACKFILL IS REQUIRED ON BOTH SIDES OF (214-358-0174 Rodolfo D'Arlach)
COARSE AGGREGATE, SEE SPECS STRUCTURE OR ELEMENT, BACKFILL SHALL BE
PLACED SIMULTANEOUSLY ON BOTH SIDES SO THAT MEP ENGINEER
THE BACKFILL HEIGHT ON ONE SIDE, DOES NOT ME Engineers, Inc.
SLAB SUBGRADE 2'-0" COLLECTOR PIPE
EXCEED THE HEIGHT ON THE OPPOSITE SIDE OF 1825 Market Center Blvd., Suite 600
PREPARATION AS SPEC'D. SEE MECHANICAL DRAWINGS Dallas, TX 75207
FOR TYPE, SIZE, LOCATION MORE THAN 4'-0". (214-741-1589 Drew Shivley)
UNDER BASEMENT SLAB
SLAB ON VOID BASEMENT WALL BACKFILL AND SLOPE
ELEVATOR CONSULTANT
TYPICAL DETAIL F TYPICAL DETAIL K Persohn | Hahn Associates, Inc.
NO SCALE NO SCALE H 8612 Broad Meadow Lane
McKinney, TX 75071
SURFACE TREATMENT (972-832-4232 Tom Williams)
EXTERIOR C.J.
COMPACTED
(TOPSOIL, PAVING, ETC.) 2-FOOT THICKNESS OF WELL NOTES:

CLAY CAP
SEE ARCHITECTURAL OR GRADE BEAM INTERIOR DESIGNER

COMPACTED, IMPERVIOS CLAY COVER BE 1. BACKFILL SHALL NOT BE PLACED AGAINST LIMIT OF
2'-0"
CIVIL DRAWINGS FOR PLACED OVER THE BACKFILL SURFACE TO FOUNDATION WALL UNTIL ALL SUPPORTING Rottet Studio
EXCAVATION SLOPE 808 Travis Street, Suite 100
MATERIALS AND SLOPES REDUCE INFILTRATION IN AREAS NOT SLABS, BEAMS, STRUTS, ETC., HAVE ATTAINED AW AY
1'-0"
MAX.
Houston, TX 77002
COVERED NY PAVEMENT. THEIR 28-DAY DESIGN STRENGTH, UNLESS (713-221-1830 x 6105 Anja Majkic)
PROPER BRACING IS INSTALLED IN A MANNER
PROTECTIVE BOARD TO APPROVED BY THE ARCHITECT.
PREVENT PUNCTURES
DURING 2. WHERE BACKFILL IS REQUIRED ON BOTH
CONSTRUCTION SIDES OF STRUCTURE OR ELEMENT, BACKFILL FORMED VOID
SHALL BE PLACED SIMULTANEOUSLY ON BOTH REFER TO www.datumengineers.com | Co. Reg. No. F-2819
SIDES SO THAT THE BACKFILL HEIGHT ON ONE TYPICAL DETAIL. Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
SIDE, DOES NOT EXCEED THE HEIGHT ON THE
OPPOSITE SIDE BY MORE THAN 4'-0". Datum Project No. 19166
BASEMENT WALL
(SEE ARCH'L. FOR DATE ISSUE TITLE
WATERPROOFING) 04/03/2020 SCHEMATIC DESIGN PRESENTATION

1. BOTH FACES OF THE GRADE BEAM 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
CONTROLLED TO BE FORMED IN ACCORDANCE 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
BACKFILL WITH EXPANSIVE CLAY NOTE #4. 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
SEE GEN'L RETENTION SYSTEM 2. SOILS PLACED ALONG THE 10/30/2020 ISSUE FOR PERMIT
NOTES EXTERIOR OF GRADE BEAM 12/18/2020 90% CONSTRUCTION DOCUMENTS
SHOULD BE ON-SITE CLAY SOILS 01/25/2021 100% CONSTRUCTION DOCUMENTS
PLACED AND COMPACTED TO AT
LEAST 93% OF MAXIMUM DRY
FILTER FABRIC REQUIRED DENSITY AT A MINIMUM OF 4
ON VERTICAL CUT WHEN PERCENTAGE POINTS ABOVE RESERVED FOR REVIEWERS NOTES
SLAB VOID SAND IS RETAINED OPTIMUM MOISTURE CONTENT AS

2'-0"
MIN.
NOTE: OBTAINED USING THE STANDARD

GRADE SHALL BE SMOOTH, EVEN PROCTOR METHOD (ASTM D-698).
LEVEL & DRY BEFORE INSTALLING 3. ALL TRENCHES OR OTHER
VOID BOXES. REFER TO VOID DETAILS COARSE AGGREGATE, SEE SPECS
DISTURBANCES IN THIS BACKFILL
FOR APPLICATION. SHALL BE RECOMPACTED TO
2'-0" 5'-0". COLLECTOR PIPE COMPLY WITH THE SPECIFIED
MIN. SEE MECHANICAL DRAWINGS BACKFILL MATERIAL.
SLAB SUBGRADE FOR TYPE, SIZE, LOCATION
STRUCTURAL SLAB VOID PREPARATION AS AND SLOPE EXTERIOR GRADE BEAM BACKFILL DETAIL WHERE LOW P.I.
SPEC'D. UNDER BASEMENT WALL BACKFILL FILL DEPTH IS GREATER THAN GRADE BEAM
TYPICAL DETAIL L BASEMENT SLAB
TYPICAL DETAIL TYPICAL DETAIL
NO SCALE
NO SCALE
N NO SCALE
P
MAPLE TERRACE
3001 MAPLE AVENUE
EXPANSIVE CLAY SOIL DETAILS
190013
PROJECT NUMBER
T.O.S.C. EL. = 481.17'
PIER SCHEDULE 30 BAR DIA.
SHAFT VERTICAL CAPACITY NOTE: ROUND TIES THUS: MAY BE USED IN

SEE PLAN FOR TOP OF PIER MARK SPIRALS PENETRATION
DIAMETER BARS (K) LIEU OF SPIRALS. BAR SIZE AND SPACING WILL
ELEVATION AND DETAIL REFERENCE. T.O.S.C. EL.
REMAIN THE SAME.
ESTIMATED DEPTH TO BEARING STRATUM P1 18
SEE SEE
5'-0" 300K
IS FOR ESTIMATING PURPOSES = 36.5'
SCHEDULE SCHEDULE
REFER TO SECTION
HOOK DWLS. @ (CC)
P2 24
SEE
SCHEDULE
SEE
SCHEDULE 6'-0" 530K STANDARD PIER DEVELOPER
DOWELS TO GRADE BEAM
SEE SEE
REINFORCING SCHEDULE DRILLED PIER NOTES:
DIAMETERS
P3 36 10'-0" 1180K OR WALL ARE SAME SIZE Hines
INCREASE SHAFT SCHEDULE SCHEDULE 2200 Ross Avenue, Suite 4200W
44 BAR
AND NUMBER AS VERTICAL
DIAMETER AS BARS IN PIER Dallas, TX 75201
#4@6" FOR
REQUIRED FOR CASED P4 36 14#10 15'-0" 1300K SHAFT VERTICAL (972-716-2908 Corbin Eckel)
TOP 4'-0", REST SPIRALS 1. PIER DRILLING MUST BE INSPECTED BY THE OWNER'S GEOTECHNICAL ENGINEER.
HOLES TO ALLOW FOR AT 12" DIAMETER BARS CONTRACTOR SHALL CONTACT THE GEOTECHNICAL ENGINEER AT LEAST 2 DAYS IN
TOP OF PIER EL. 2800 Post Oak Blvd., 49th Floor
WATER INFILTRATION CASING
FOR CASED PIERS AS
CASING TO SEAL OFF

ADVANCE OF DRILLING TO COORDINATE INSPECTION. Houston, TX 77056
BOTTOM OF CASING
REQUIRED TO SEAT
SEE 18" 6#6 #3@6"

-
DIA @(CC)
P5 42 11#10 11'-0" 1620K (713-621-8000 Juan Delgado)
DIA. @(C)
2"
SCHEDULE
44 BAR
78 BAR
2. FOUNDATION DESIGN IS BASED ON AN ALLOWABLE END BEARING VALUE OF:
24" 6#8 #3@12"
P5A NOT USED
EQUITY PARTNERS
ALLOWABLE SKIN FRICTION FOR COMPRESSION OF:
36" 8#10 #3@12" McNair Interests
15,000 LBS./SQ. FT 109 N. Post Oak Lane, Suite 600
REFER TO DETAIL
BEARING STRATUM (SEE Houston, TX 77024
42" 10#10 #4@12" 20A/S302-OF FOR PIER ALLOWABLE SKIN FRICTION FOR TENSION OF:
DRILLED PIER NOTES) (Drew Steffen)
INFORMATION 10,000 LBS./SQ. FT
NOTE: Mitsui Fudosan America
SEE PIER SCHEDULE FOR SIZE OF PIERS USED ON THIS PROJECT. 1251 Avenue of the Americas, Suite 800
.016 ALLOWABLE END BEARING PRESSURE OF:
95,000 LBS./SQ. FT New York, New York 10020
(David Leff)
THESE VALUES ARE BASED ON GEOTECHNICAL ENGINEERING REPORT PROJECT
NO. 19:7809-A DATED MAY 7, 2020, PREPARED BY ECS SOUTHWEST, LLP. OFFICE/RETAIL ARCHITECT
GRADE BEAM OR WALL TO PIER 5G Studio Collaborative, LLC.
3. BEARING STRATUM SHOWN ON THE PIER DETAILS IS UNWEATHERED GREY LIMESTONE. 1217 Main St., Suite 500
TYPICAL DETAIL Dallas, TX 75202
PITCH

4. DISTRIBUTION OF THE VARIOUS PIER TYPES IS INDICATED ON THE PIER PLAN.
SPIRAL OR TIES AS
SCHEDULED. PROVIDE ONE
B NO SCALE
C, CC 5. PIER SIZES, REINFORCING, AND DEPTHS ARE SHOWN IN THE PIER SCHEDULE ON SHEET S302-OF.
GFF Architects
COMPLETE FLAT TURN TOP 2808 Fairmount St., Suite 300
AND BOTTOM 6. THE CONTRACTOR SHALL VERIFY DEPTHS OF PIERS BEFORE PIER STEEL IS CUT. PIER STEEL Dallas, TX 75201
MEASURED FROM BOTTOM OF CASING
SHALL BE DELIVERED TO THE JOBSITE IN STANDARD STOCK LENGTHS AND CUT AS REQUIRED (214-303-1500 Michael Reyes)
PENETRATION FOR CASED PIERS
BY THE ACTUAL FIELD MEASURED DEPTH OF THE PIER. SPLICES IN VERTICAL REINFORCING
SHALL BE 78 BAR DIAMETERS, AND REINFORCING SHALL EXTEND TO 3 INCHES FROM BOTTOM ZONING/ENTITLEMENT
OF HOLE, UNLESS SHOWN OTHERWISE. SPLICED BARS SHALL BE LESS THAN 6" APART Baldwin Associates
SEE PIER
LAP SPLICE
SEE COL.
SEE SCHEDULE
SEE COL. SCHEDULE
SCHED.
SCHEDULE FOR 7. THE CONTRACTOR AND/OR TESTING LAB SHALL TAKE ACCURATE MEASUREMENTS OF THE Dallas, TX 75226
COLUMN
SHAFT DIAMETER DEPTH OF PENETRATION INTO THE BEARING STRATUM, TO BE ASSURED OF CONFORMANCE (214-824-7949 Robert Baldwin)
SEE PLAN
LAP SPLICE
AND WALL REBAR SHALL WITH THE DEPTH OF PENETRATION REQUIRED BY THE PIER SCHEDULE, AND SUBMIT A
REINFORCING RUN CONT. REPORT OF DEPTHS OF PENETRATION DRILLED TO THE ENGINEER. GEOTECH
T.O.S.C. EL.
SEE PLAN THROUGH WALL 8. REINFORCING STEEL SHOP DRAWINGS SHALL INCLUDE DRAWINGS FOR PLACING OF ECS Southwest, LLP
3" C PILASTER 3033 Kellyway Drive, Suite 110
L EAR TEMPLATES TO SET DOWELS IN PIERS.
SEE SCHED. (972-392-3222 Siddharth Neekhra)
T.O.S.C. EL. 9. PIER HOLES SHALL BE COMPLETED AND FILLED WITH CONCRETE WITHIN 6 HOURS AFTER
PROFILE OF COLUMN ABOVE
SEE PLAN COMPLETION OF SHAFT EXCAVATION. CIVIL ENGINEER
BEAM BEYOND
10. ELEVATION OF TOP OF PIERS, WHERE NOT GIVEN, IS AT THE BOTTOM OF THE DEEPEST
SCHEDULED DEPTH
PROVIDE 3 SIDE SPACERS 13455 Noel Road, Two Galleria Office Tower, Suite 700
1'-2"
INTERSECTING BEAM OR WALL SUPPORTED BY THE PIER. CONTRACTOR SHALL CALCULATE Dallas, TX 75240
AT BOTTOM OF CAGE & AT
ALL TOP OF PIER ELEVATIONS BEFORE PROCEEDING WITH THE PIER DRILLING OPERATION. (972-770-1300 Alex Rathbun)
20' O.C. MAXIMUM
SPACING. REFER TO
SPECIFICATIONS. 11. REMOVE EXCESS CONCRETE AT THE TOP OF THE PIER BEYOND THE LIMITS OF THE PIER LANDSCAPE ARCHITECT
PILASTER @ PIER
3"
1'-0"
DIAMETER. FORM SIDES OF PIER EXTENSIONS TO THE SAME DIAMETER AS SHAFT BELOW, SWA Group
REFER TO 20J TO 2001 Irving Boulevard, Suite 157
20P/S302-OF AVOIDING OVERHANGS IN EXPANSIVE CLAY. USE SUREVOID COMMERCIAL SURETOP OR
Dallas, TX 75207
1'-9"
PROVIDE 2 END SPACERS SONOTUBE COLLAR FORMS AT TOP OF EACH HOLE TO MAINTAIN SHAPE. (214-954-0016 Chuck McDaniel)
TOP OF PIER EL.
ON OPPOSITE SIDES AT TOP OF PIER EL. 12. DRILL PIERS AFTER ALL SOIL TREATMENT, FILLING, AND COMPACTION HAVE BEEN
SEE COL. SCHED.

BOTTOM OF CAGE. REFER COMPLETED IN THE AREA TO BE DRILLED. DISTURBED AREAS SHALL BE RECOMPACTED. STRUCTURAL
LAP SPLICE
TO SPECS. Datum Engineers
SEE COL. SCHEDULE
SHAFT SEE PLAN FOR CONTRACTOR SHALL PROVIDE ADDITIONAL PIER REINFORCING STEEL (TIES, SPIRALS AND/OR 6516 Forest Park Road
PIER MARK. 13.
VERTICAL REINFORCING), AS REQUIRED TO FACILITATE PLACEMENT OF THE REINFORCING Dallas, TX 75235
LAP SPLICE
9"
DIA. ADDN'L 3#9 VERT. CAGE WITHOUT BUCKLING, COLLAPSING OR EXCESSIVE DEFLECTION. (214-358-0174 Rodolfo D'Arlach)
SEE DETAIL SEE DETAIL
20A/S302-OF FOR W/#4 X @ 18" 1'-6" PILASTER TO MATCH SCHED.
20A/S302-OF COLUMN ABOVE - CAST MEP ENGINEER
FOR PIER PIER INFORMATION PIERS SHALL NOT BE LARGER THAN THE DIAMETER SHOWN (PLUS 2-INCH TOLERANCE) IN
MONOLITHICALLY WITH 14. ME Engineers, Inc.
INFORMATION PIER DOWELS TO MATCH WALL REINF. ORDER TO LIMIT SURFACE AREA IN CONTACT WITH EXPANSIVE CLAY. 1825 Market Center Blvd., Suite 600
ADJACENT WALLS.
Dallas, TX 75207
CONCRETE COLUMN OVER PIER SCHED. WALL VERT. REINF. (214-741-1589 Drew Shivley)
CASED STRAIGHT SHAFT PIER 15. WHERE TWO PIERS ARE CLOSER TOGETHER THAN 2.5 TIMES THE DIAMETER OF THE
LARGER PIER (CLEAR DISTANCE), WAIT AT LEAST 24 HOURS AFTER CASTING THE FIRST PIER
TYPICAL DETAIL A D TYPICAL DETAIL PLAN F BEFORE DRILLING THE SECOND.
ELEVATOR CONSULTANT
NO SCALE E 3/4" = 1'-0" Persohn | Hahn Associates, Inc.
McKinney, TX 75071
EXTEND
WALL #3 X @ 6"
#3 X @ 6" REINF. INTO
INTERIOR DESIGNER
NOTE: PILASTER Rottet Studio
PROVIDE CORNER 808 Travis Street, Suite 100
BARS PER 3/S304-OF. Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
1'-0"
WALL REINFORCING
NOT SHOWN FOR
CLARITY.
3#7 VERTICAL 214-358-0174 512-469-9490 210-858-2880
1'-0"
DATE ISSUE TITLE
WALL
1#7 VERTICAL REINFORCING
NOT SHOWN
FOR CLARITY.
1'-0"
PLAN 1'-0"
PLAN
CORNER PILASTER RE-ENTRANT CORNER PILASTER
TYPICAL DETAIL J TYPICAL DETAIL K

NO SCALE NO SCALE
NOTE: NOTE:
PROVIDE CORNER PROVIDE CORNER SEE PLAN ALL WALL REINF. REV. DATE ISSUE TITLE
BARS PER 3/S304-OF. BARS PER 3/S304-OF. FOR PIER SHALL RUN CONT. .05 12/18/2020 Permit Set Update
COLUMN ABOVE, SEE PLAN FOR THROUGH COLUMN /
PIER MARK MARK SEE PLAN FOR .016 05/03/2021 ADDENDUM 08
(REINF. NOT SHOWN PILASTER
FOR CLARITY) PIER MARK
SCHED. SCHED.
SCHED. PILASTER
COLUMN ABOVE COLUMN ABOVE
GRADE BEAM
REINFORCING
6"
NOT SHOWN FOR

CLARITY.
#3 X @ 6" COL. DIM 3#7 VERTICAL

PILASTER TO MATCH
COL. DIM + 12" SCHED. SCHED. COLUMN
COLUMN ABOVE ABOVE - CAST
MONOLITHICALLY
SCHED. PILASTER WITH ADJACENT
PLAN
WALLS AND GRADE
BEAMS.
PLAN PLAN
PLAN MAPLE TERRACE
3001 MAPLE AVENUE
PERIMETER PILASTER BASEMENT WALL CORNER PILASTER BASEMENT WALL RE-ENTRANT CORNER PILASTER BASEMENT WALL PILASTER DALLAS, TEXAS, 75201
TYPICAL DETAIL L TYPICAL DETAIL M TYPICAL DETAIL N TYPICAL DETAIL P TYPICAL PIER DETAILS AND TOP
NO SCALE NO SCALE NO SCALE NO SCALE OF PIER DETAILS
TYPICAL PIER DETAILS - CASED STRAIGHT SHAFT PIERS AND TOP OF PIER DETAILS 190013
PROJECT NUMBER
CONTR. CONSTRUCTION OR
SLAB-ON-GRADE NOTES:
JOINT CONTROL JOINTS ON
1. SEE PLAN AND GENERAL NOTES FOR THICKNESS OF
SLAB (T) AND REINFORCING. POUR C.L. OF COLUMN IF
2. REINFORCING TO BE LAPPED 30 BAR DIA. MINIMUM STRIP SLAB IS EXPOSED.
OR TWO CROSSTIES FOR WIRE MESH. SEE GENERAL
3. SEE SPECIFICATIONS FOR SUPPORT OF REINFORCING. NOTES.
4. SEE OTHER DETAILS FOR CONDITIONS AT GRADE BEAMS,
15'-0"
MAX
COLUMNS AND EXPANSION JOINTS.
DEVELOPER
EDGE TO 1/8" RADIUS STOP SLAB REINF.
1/4" WIDE JOINT. Hines
FILL JOINT WITH EACH SIDE OF JOINT AT JOINT 2200 Ross Avenue, Suite 4200W
TOOL OR SAWCUT
ELASTOMERIC SEALANT
CLEAR
Dallas, TX 75201
1 1/4"
3/4" DIA. x 2'-0"
SEE SPECIFICATIONS (972-716-2908 Corbin Eckel)
SMOOTH BARS @ 18" CONSTRUCTION
T/4
JOINTS 2800 Post Oak Blvd., 49th Floor

Houston, TX 77056
T
T
T/2
EQUITY PARTNERS
McNair Interests
CUT AND REMOVE 4" WIDE SUBSLAB MATERIAL 109 N. Post Oak Lane, Suite 600
VAPOR BARRIER SEE GENERAL NOTES Houston, TX 77024
SEE SPECIFICATIONS STRIP OF ALTERNATE WIRES (Drew Steffen)
OR BARS AT CONTROL JOINT AND SPECIFICATIONS
CONTROL JOINT (CT.J.) CONSTRUCTION JOINT (C.J.) CONTROL JOINTS

COLUMN CENTERLINES
TYPICAL
TYPICAL (David Leff)
NOTES:
1. JOINTS ARE REQUIRED IN ALL EXPOSED SLABS AT
A MAXIMUM SPACING OF AS SHOWN IN NOTE EACH
NOTES:
1. SLABS SHALL BE POURED IN A STRIP PATTERN
SCHEMATIC POUR STRIP LAYOUT WHERE SLAB IS EXPOSED
WAY. LOCATE JOINTS ON COLUMN CENTERLINES. PLAN
2. SAW CUTS ARE TO BE MADE AS SOON AS SLAB
WITH WIDTHS NOT EXCEEDING THAT SHOWN IN
NOTES. NOTES:
1. PROVIDE A CONSTRUCTION OR A CONTROL
BUILDING PAD PREPARATION Dallas, TX 75202
CAN SUPPORT WORKERS AND EQUIPMENT AND 2. IF METAL FORMS ARE USED, REMOVE THEM
BEFORE SHRINKAGE CRACKS OCCUR. BEFORE POURING ADJACENT SLAB. JOINT ON THE CENTERLINES OF COLUMNS, NOTE:
ONLY IF DIAMOND BLOCKOUTS ARE USED. FOR EXTERIOR COLUMNS, 1. THE BUILDING PAD PREPARATION REQUIREMENTS ARE BASED ON THE RECOMMENDATIONS OF MASTER/MULTIFAMILY ARCHITECT
3. CLEAN JOINTS BEFORE FILLING WITH SEALANT.
2. INFILL STRIPS CAN BE PLACED AFTER PLACE DIAGONAL BARS THE GEOTECHNICAL REPORT PREPARED BY ECS SOUTHWEST LLP, DATED, JUNE 18 2020 FOR A GFF Architects
CALCUATED POTENTIAL VERTICAL RISE OF THE PAD OF 1 INCHES. 2808 Fairmount St., Suite 300
EXPOSED SLAB-ON-GRADE TYPICAL DETAIL

INITIAL SLAB STRIPS HAVE CURED FOR
3 DAYS. B C AT COLUMN CORNERS THUS:
Dallas, TX 75201
2. STRIP ALL VEGETATION, ORGANIC TOPSOIL AND CLAY WITHIN THE BUILDING LINES TO A DEPTH
NO SCALE AS SHOWN BELOW.
ZONING/ENTITLEMENT
SUBGRADE REWORK TOTAL DEPTH OF EXCAVATION Baldwin Associates
FROM EXISTING GRADE. 3904 Elm Street, Suite B
Dallas, TX 75226
DRAPE REINFORCING OPTION #1 8 FEET OF SELECT FILL 8’-0” (214-824-7949 Robert Baldwin)
CENTER LINE OF WALL CONCRETE COLUMN
REFER TO SEE PLAN & SCHEDULE OPTION #2 1 FEET OF SELECT FILL OR 8 INCHES 10’-0” GEOTECH
ARCHITECTURAL OF FLEX BASE CAPPED ON 9 FEET ECS Southwest, LLP
SLAB-ON-GRADE OF MOISTURE CONDITIONED CLAY 3033 Kellyway Drive, Suite 110
DRAWINGS FOR LOCATION ADDN'L #4 X 4'-0" @ 12" SEE GENERAL NOTES Carrollton, TX 75006
8"
T.O.S.C. EL. 3. JUST PRIOR TO FILL PLACEMENT, SCARIFY EXPOSED SUBGRADE AND COMPACT TO 95 PERCENT
#3@18" SEE PLAN OF MAXIMUM DENSITY (ASTM D-698) AT A MOISTURE CONTENT ABOVE OPTIMUM. CIVIL ENGINEER
1'-0"
8" T.O.S.C. EL. TOP OF PIER 4. FOR OPTION #1, PLACE AND COMPACT SELECT FILL TILL UNDER THE SLAB. PLACE FILL IN LIFTS 13455 Noel Road, Two Galleria Office Tower, Suite 700
SEE PLAN NOT TO EXCEED 8” (LOOSE MEASURE). COMPACTING EACH LIFT TO 95 PERCENT OF MAXIMUM Dallas, TX 75240
DENSITY AT OR ABOVE OPTIMUM MOISTURE CONTENT. (972-770-1300 Alex Rathbun)
1'-0"
SLAB DEPRESSION UP TO 3" PIER, PIER CAP 5. FOR OPTION #2, 1 FEET OF SELECT FILL OR 8 INCHES OF FLEX BASE SHALL BE CAPPED ON LANDSCAPE ARCHITECT
OR FOOTING, MINIMUM 9 FEET OF MOISTURE CONDITIONING. DURING THE PROCESS, THE CLAY SHOULD SWA Group
SEE PLAN RECEIVE ADEQUATE AMOUNTS OF WATER TO ENSURE A UNIFORM MOISTURE CONTENT OF AT 2001 Irving Boulevard, Suite 157
ELEVATION LEAST 4 PERCENTAGE OR HIGHER ABOVE THE OPTIMUM MOISTURE CONTENT. ONCE Dallas, TX 75207
OPTIONAL EQUAL EQUAL (214-954-0016 Chuck McDaniel)
APPROPRIATELY MIXED, THE MATERIAL SHOULD BE COMPACTED TO AT LEAST 93% OF MAXIMUM
CONSTRUCTION DRY DENSITY AS OBTAINED USING THE STANDARD PROCTOR METHOD (ASTM D-698). IF THE FILL
JOINT 2'-0" DEPTH EXCEEDS 15 FEET, BOTTOM 5 FEET SHALL BE COMPACTED TO 98% OF MAXIMUM DRY STRUCTURAL
3#5 DENSITY AS OBTAINED USING THE STANDARD PROCTOR METHOD (ASTM D-698). Datum Engineers
6. SELECT FILL SHALL HAVE A PLASTICITY INDEX BETWEEN 5 AND 15 WITH 40-70% PASSING AT Dallas, TX 75235
NO.200 SIEVE. (214-358-0174 Rodolfo D'Arlach)
7. FLEX BASE SHALL BE TxDOT ITEM 247, TYPE D, GRADE 1 OR 2. MEP ENGINEER
SLAB-ON-GRADE STIFFENER BEAM SLAB-ON-GRADE AT CONCRETE COLUMN ME Engineers, Inc.
8. CONTRACTOR SHALL CONTACT THE OWNER’S GEOTECHNICAL ENGINEER AT LEAST 7 DAYS 1825 Market Center Blvd., Suite 600
TYPICAL DETAIL TYPICAL DETAIL H BEFORE THE START OF FILLING OPERATIONS FOR THE BUILDING PAD. COMPACTION AND Dallas, TX 75207
1'-0" NO SCALE F G NO SCALE

MOISTURE CONTENT OF SUBGRADE AND EACH LIFT OF FILL SHALL BE TESTED BY THE
GEOTECHNICAL ENGINEER ( OR HIS DESIGNATED REPRESENTATIVE) AND APPROVED BEFORE
PLACING NEXT LIFT. ADJUST MOISTURE CONTENT AND RECOMPACT WHERE REQUIRED.
ELEVATOR CONSULTANT
SLAB DEPRESSION GREATER THAN 3" TO 18" 9. SELECT FILL PLACED OUTSIDE THE GRADE BEAMS LINES SHALL BE REMOVED AND REPLACED McKinney, TX 75071
PROVIDE 2#4X4'-0" WITH ON-SITE CLAY BACKFILL. (972-832-4232 Tom Williams)
DIAGONAL BARS
2'-0" IN TOP OF SLAB REPLACE ALL CUT BARS 10. SELECT FILL MATERIAL WHICH IS NOT PURCHASED FROM AN APPROVED PLANT, SUCH AS ON- INTERIOR DESIGNER
WITH SAME SIZE BAR & SITE OR PRIVATELY OWNED PIT MATERIAL, MUST BE CONTINUOUSLY MONITORED BY AN
DRILL & GROUT CENTER LINE OF LOAD Rottet Studio
30 DIA. EXTENSION EA. APPROVED TESTING LABORATORY HIRED AND PAID BY CONTRACTOR. 808 Travis Street, Suite 100
SIDE OF OPNG. DOWELS. SEE BEARING CMU, WALL REFER
TO ARCHITECTURAL Houston, TX 77002
GENERAL NOTES. 11. SELECT FILL MATERIAL MUST PROVIDE A SOLID WORKING PAD FOR OTHER TRADES DURING WET (713-221-1830 x 6105 Anja Majkic)
DOWEL SIZE AND DRAWINGS FOR LOCATION WEATHER. ALL SOFT SPOTS MUST BE RECOMPACTED PRIOR TO CONCRETE PLACEMENT. IF ON-
SPACING TO SITE OR PRIVATE PIT MATERIAL IS USED, PLANT MATERIAL CONFIRMING TO TxDOT TYPE A,
MATCH WALL GRADE 1 IS REQUIRED FOR TOP LIFT.
3'-0" MAX.
REINF. 4#4 CONT. TOP & BOT.

3"
ADD 1#3x2'-0" DIAG. AT 12. STRUCTURES EXTENDING GREATER THAN 10’-0” BELOW ADJACENT GRADE AREAS WILL NOT
3 1/2" WIDE X EA. CORNER OVER 8" REQUIRE ANY SUBGRADE REWORK. NOT REQUIRED AT B1 OR B2 LEVELS, NOT REQUIRED AT www.datumengineers.com | Co. Reg. No. F-2819
WATERSTOP 1 1/2" DEEP TOP OF SLAB REINF. Dallas Austin San Antonio
#3 @ 12" SUSPENDED LEVEL 1. 214-358-0174 512-469-9490 210-858-2880
SHEAR KEY, TYP.
BLOCKOUTS Datum Project No. 19166
45° DATE ISSUE TITLE
8"
1'-0"
GRADE BEAM, 04/03/2020 SCHEMATIC DESIGN PRESENTATION
CONSTRUCTION
JOINT OR RECESS
SLAB-ON-GRADE 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
1'-0"

DRAPE SLAB REINF. 1. FLOOR SLAB SHALL BE 6-INCH THICK CONCRETE SLAB-ON-GRADE OVER SPECIFIED VAPOR 10/30/2020 ISSUE FOR PERMIT
AROUND SLAB BARRIER OVER PREPARED FILL PER BUILDING PAD PREPARATION NOTES. SEE NOTE 11 12/18/2020 90% CONSTRUCTION DOCUMENTS
BLOCKOUTS WHERE ABOVE TO CONFIRM.
CORNERS POSSIBLE EQUAL EQUAL 01/25/2021 100% CONSTRUCTION DOCUMENTS
1 2. REINFORCE SLAB WITH #4@12" O.C., E.W., PLACED 1 1/4" CLEAR FROM TOP OF SLAB.
1 2'-0"
1'-0" 1'-0" 1'-0" NOTE: RESERVED FOR REVIEWERS NOTES
FABRICATOR TO LOCATE THESE 3. PROVIDE ONE OF THE FOLLOWING JOINTS ON THE CENTER LINES OF ALL COLUMNS AND AT A
#4@12" MAXIMUM SPACING OF 15'-0" ON CENTER, EACH WAY, WHERE CONCRETE SLAB IS EXPOSED.
BARS ON THE SHOP DRAWINGS.
SLAB DEPRESSION GREATER THAN 18" TO 36" SEE 20H/S303-OF.
DROP IN SLAB-ON-GRADE A. CONSTRUCTION JOINTS WHERE DETAILED ON DRAWINGS.
TYPICAL DETAIL RE-ENTRANT CORNER REINFORCING SMALL SLAB-ON-GRADE BLOCKOUT STIFFENER BEAM AT CMU WALL B. SAW-CUT CONTROL JOINTS ELSEWHERE. DEPTH SHALL BE A MINIMUM OF 1/4 OF
NO SCALE TYPICAL DETAIL TYPICAL DETAIL TYPICAL DETAIL THE SLAB THICKNESS. SAW CUTS SHALL BE MADE AS SOON AS SLAB CAN SUPPORT
WORKERS AND EQUIPMENT AND BEFORE SHRINKAGE CRACKS OCCUR.
E NO SCALE J K L C. ALIGN CONSTRUCTION AND CONTROL JOINTS WITH JOINTS IN FLOOR TILE.
4. A METAL CONSTRUCTION JOINT FORM MAY BE USED. REMOVE METAL FORMS BEFORE
PLACING SECOND POUR.
DRAINAGE
COURSE SLAB-ON-GRADE
VAPOR
BARRIER, PER
SPEC.
T.O.S.C. EL.
SEE PLAN 2'-0"
ADDN'L #4@12"
W/ 3#4 CONT.
1'-0"
FILL SEE BUILDING
PAD PREPARATION
NOTES ON S303-OF
1'-6"
PLUMBING PIPE, FILTER FABRIC,
SEE PLUMBING PER SPEC.
DWGS. FOR PIPE
SIZE AND
ELEVATION
SOIL PREPERATION FOR TRENCHES MAPLE TERRACE

UNDER SLAB-ON-GRADE 3001 MAPLE AVENUE
TYPICAL DETAIL TYPICAL SLAB-ON-GRADE
NO SCALE
M U DETAILS
TYPICAL SLAB-ON-GRADE DETAILS 20 190013

PROJECT NUMBER
"T"/3 "T"/3 "T"/3 3'-0"
3'-0"
NOTES:
1. PROVIDE CORNER BARS TO MATCH SIZE AND LOCATION OF
ALL HORIZONTAL GRADE BEAM AND WALL BARS EXCEPT 1 1/2" DEEP
1 1/2" DEEP
CONTINUOUS KEY REINFORCING
TO BE
HOOKED TOP AND BOTTOM BARS.
2. CORNER BARS ARE NOT REQUIRED WHEN BEAM OR WALL
CONTINUOUS
KEY
#5@12" X DOWEL SCHEDULE
CONTINUOUS BARS HAVE HOOKED ENDS. TURN HOOKS SIDEWAYS.
THROUGH JOINT MARK SIZE A B C
#5@12" X DIAG. BARS EA. FACE 44 BAR DIAMETER DEVELOPER
INTERMITTENT 1'-0"
1 1/2"
TO MATCH SMALLER CORNER BARS EACH FACE TO Hines
LONG SHEAR KEY @ BAR @ INTERSECTION EACH LEG (TYP.) DWL. A #4 8" 3'-0" --- 2200 Ross Avenue, Suite 4200W
MATCH SMALLER BAR AT
2'-0" O.C. IF JOINT IS Dallas, TX 75201
INTERSECTION.
ABOVE GRADE DWL. B #4 3'-0" 3'-0" --- (972-716-2908 Corbin Eckel)
44 BAR DIAMETER
DWL. C #4 --- 4'-0" --- Houston, TX 77056
EACH LEG (TYP.)

CONTINUOUS KEY AND (713-621-8000 Juan Delgado)
WATERSTOP IF JOINT IS
(24" MIN.)
BELOW GRADE, REFER NOTES:
CONTINUOUS EQUITY PARTNERS
WATERSTOP, REFER TO TO SPECIFICATIONS 1. SCHEDULED DOWELS ARE MARKED "DWL." ON THE
McNair Interests
SPECIFICATIONS SECTIONS AND DETAILS. 109 N. Post Oak Lane, Suite 600
CORNER BARS
CORNER BARS Houston, TX 77024
EA. FACE TO 2. DOWEL SPACING TO BE THE SAME AS VERTICAL BEAM OR (Drew Steffen)
MATCH BARS IN WALL REINFORCEMENT, UNLESS OTHERWISE NOTED ON
DISCONTINUOUS DETAILED DETAILS. Mitsui Fudosan America
"T" - REFER TO MEMBER REINFORCING STOP 2" 1251 Avenue of the Americas, Suite 800
SECTIONS SHORT OF FORM,TYP. New York, New York 10020
(David Leff)
PLAN OFFICE/RETAIL ARCHITECT

CONSTRUCTION JOINT SLAB-ON-GRADE TO WALL 5G Studio Collaborative, LLC.
TYPICAL DETAIL HORIZONTAL CONSTRUCTION JOINT IN BEAMS AND
WALLS OR VERTICAL CONSTRUCTION JOINT IN WALLS CORNER BARS AT WALL OR GRADE BEAM INTERSECTION CONSTRUCTION JOINT SLAB-ON-GRADE TO GRADE BEAM Dallas, TX 75202
NO SCALE
TYPICAL DETAIL TYPICAL DETAIL TYPICAL DETAIL MASTER/MULTIFAMILY ARCHITECT
1 NO SCALE
2 NO SCALE
3 NO SCALE 4 5 GFF Architects
Dallas, TX 75201
NOTES: 3'-3" NOTE:
1. SEE 7/S304-OF FOR SUMP PIT INFO. #4X @ SUMP ZONING/ENTITLEMENT
1. PROVIDE ECCENTRIC
2. SEE 8/S304-OF FOR ELEVATOR SILL INFO. WALL BEYOND Baldwin Associates
BASEPLATE TO ACHIEVE 4" OF
3. SEE 9/S304-OF FOR ELEVATOR DIVIDER MIN. EDGE DISTANCE AS SHOWN. 3904 Elm Street, Suite B
DWL. B@12" W/ Dallas, TX 75226
BEAM INFO. SEE ARCH'L DWG. FOR 3 1/2" REFER TOP ?
1#4 CONTINUOUS SHAFT OPENING (214-824-7949 Robert Baldwin)
GRATING & SUPPORT
WALL, SEE 6/S304- REFER TO PLAN
INFO. 2. SEE 20/S304-OF FOR TOP
OF FOR SIZE & GEOTECH
SLAB BEYOND CONNECTION.
REINF. SEE ELEVATOR MFR. PL. 3/8x9x1'-0" WITH ECS Southwest, LLP
T.O.S.C. EL. 3033 Kellyway Drive, Suite 110
PIT SLAB, SEE 6/S304-OF FOR SILL. INSTALL W/ 4 - 1/2" DIA. x 0'-6" 3. SEE 18/S304-OF FOR TUBE TO
SEE PLAN 6" Carrollton, TX 75006
1'-0"
FOR SIZE & REINF. 3/4" DIA. 0'-6" EXPANSION CONCRETE BEAM HEADED STUDS 3/16 COLUMN CONNECTION.
WATERSTOP OR SLAB, SEE (972-392-3222 Siddharth Neekhra)
BOLTS @ 1'-0" @ 6" HORIZONTALLY
PLAN
SLOPE CIVIL ENGINEER
TYP DIM.
2" CLR. 3/16 HSS6X6X1/2
2 1/2"
REINF. Kimley-Horn and Associates, Inc.
ELEVATOR GUIDE RAIL SUPPORT
2"
#4@12" E.W. E.F.
3'-0" @ DOUBLE PIT

2'-0" @ SINGLE PIT
1/2" NON-SHRINK
COLUMN EA. SIDE OF PIT. 13455 Noel Road, Two Galleria Office Tower, Suite 700
3"
6'-6"
3#8 CONT. TOP & BOT EA. PLATE Dallas, TX 75240

1/4 (972-770-1300 Alex Rathbun)
PL.1/2x4x1'-6"
2"
WATERSTOPS IN ALL BELOW #7@8" E.W. W/2-3/4" DIA. EXP.
2" MAXIMUM
GROUT
1'-6" OR EPOXY BOLTS LANDSCAPE ARCHITECT
GRADE CONSTRUCTION TOP & BOT. PROJECTION
SWA Group
2'-0"
JOINTS, TYP. SEE
4"
1 1/2"
#4X @ 8" 2001 Irving Boulevard, Suite 157

SPECIFICATIONS. LEVEL 7, 8, 9 Dallas, TX 75207
T.O.S.C. EL. EXTEND IN SUMP WALLS FACE OF PIT WALL (214-954-0016 Chuck McDaniel)
SEE PLAN VERT. EACH WAY OR FLOOR BEAM
6"
8"
WALL REINF. STRUCTURAL
1'-0"
MIN.
EMBED.
Datum Engineers
3"
T.O. PIER EL. HSS8X4X5/16 (LLV) DIVIDER BEAM 6516 Forest Park Road
4" Dallas, TX 75235
SEE PLAN #4 @ 8"
HORIZONTAL (214-358-0174 Rodolfo D'Arlach)
2'-0" 8" 2-Pl.3/8"X4"X0'-6" W/2- ¾" DIA.
BOLTS THROUGH BOTH ELEVATOR PIT WALL MEP ENGINEER
X 2' - 0"
SIDE WALLS OR BEAM ME Engineers, Inc.
1'-0" 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
SUMP PIT ELEVATOR DOOR SILL (214-741-1589 Drew Shivley)
ELEVATOR DIVIDER BEAM SUPPORT ELEVATOR GUIDE RAIL SUPPORT
ELEVATOR PIT WALL
TYPICAL DETAIL TYPICAL DETAIL ELEVATOR CONSULTANT
TYPICAL DETAIL 8 TYPICAL DETAIL 9 TYPICAL DETAIL 10 Persohn | Hahn Associates, Inc.
NO SCALE
6 NO SCALE
7 NO SCALE
NO SCALE NO SCALE
McKinney, TX 75071
ADDN'L. BEAM
(L1 > L2) NOTE: STIRRUP EA. SIDE INTERIOR DESIGNER
CORNER CONDITION SIMILAR. DETAILED OR OF SLEEVE Rottet Studio
L1 L2 STOP BARS 3" FROM CORNER SCHEDULED 808 Travis Street, Suite 100
DO NOT SPLICE TOP BARS BEAM 2-#5X4'-0" TOP AND Houston, TX 77002
STD. 90° AND PROVIDE CORNER BARS.
IN FIRST INTERIOR SPAN REINFORCING BOTTOM OF SLEEVE (713-221-1830 x 6105 Anja Majkic)
HOOKS DO NOT SPLICE BOTTOM L1/2 L1/3 L1/3 CONSTRUCTION JOINT
BEAM BEYOND BARS AT FIRST WITHIN
INTERIOR SUPPORT 2'-0" OF C.L. OF SPAN
22 BAR DIA.
2"
4 ADDITIONAL
SCHEDULED DEPTH D
9" MIN.
STIRRUPS 6" 6" 6" 6" www.datumengineers.com | Co. Reg. No. F-2819
DETAILED OR
214-358-0174 512-469-9490 210-858-2880

TOP OF NEXT
PIER EL. DATE ISSUE TITLE
3" 2" T.O. PIER EL. 04/03/2020 SCHEMATIC DESIGN PRESENTATION
D/4
ADDITIONAL BARS TOP BARS CONT. 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
& BOT. AS NOTED ON TOP & BOT.
1/3 "D"
PLANS OR SECTIONS 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
6"
PIER, SEE PLAN BEAM 12/18/2020 90% CONSTRUCTION DOCUMENTS
REINFORCING PIPE SLEEVE PER SPECS. SEE MEP 01/25/2021 100% CONSTRUCTION DOCUMENTS
SEE SECTIONS AND CIVIL FOR INFO. NOT SHOWN.

(LOCATE IN MIDDLE THIRD OF SPAN). INCREASE BEAM DEPTH
22 BAR DIA. AS REQ'D. TO MAINTAIN
STIRRUP MIN. 6" CONCRETE BEAM REINF. 3 1/2" DEEP SHEAR KEY
SPACING 2" 1/8 L 3/4 L 1/8 L BELOW BOTTOM OF PIPE CONTINUOUS WIDTH = BEAM WIDTH - 6"
NOTES:
1. CONDUIT AND PIPING MAY NOT BE PLACED PARALLEL TO AND SLEEVE THROUGH
FACE CONSTRUCTION
L C.L. PIER INSIDE OF BEAM FORMS OR TRENCHES.
OF JOINT
PIER 2. IF PIPE IS BEING CAST INTO A GRADE BEAM, SLEEVE MAY BE ELEVATION
OMITTED IF PIPE IS WRAPPED WITH 1/2" THICK COMPRESSABLE
ELEVATION MATERIAL.
3. NOTIFY ENGINEER IF DIMENSIONED CONDITIONS CANNOT BE MET. BEAM VERTICAL CONSTRUCTION JOINT
GRADE BEAM ELEVATION

CHANGE IN DEPTH OF GRADE BEAM OR WALL
SLEEVE THROUGH GRADE BEAM
TYPICAL DETAIL
TYPICAL DETAIL TYPICAL DETAIL TYPICAL DETAIL
NO SCALE
NO SCALE 12 NO SCALE 13 14 15
NO SCALE
1'-6"
DWL-A@12" #4 X .016 05/03/2021 ADDENDUM 08
78 BAR DIA. 2'-0" MIN.

T.O.S.C. EL.
SEE PLAN T.O.S.C. EL. T.O.S.C. EL.
1'-0"
SEE PLAN SEE PLAN

SEE PLUMBING
2"
POST 3/16
SEE PLAN
TOP OF NEXT
SEE PLUMBING FOR PIER EL.
INSIDE DIAMETER T.O. PIER EL.
PRECAST CONCRETE
PIPE
#3@12" E.W.
NOT USED
1"
SAND FILL AROUND BEAM BEAM
2"
CONCRETE PIPE
5"
REINFORCING SEE PLAN

SEE SECTIONS PL.1/2X14"X1'-2" BEAM
BEAM OR SLAB
5"
W/ 4- 3/4" DIA. X SEE PLAN

L4X4X3/8X0'-4" SEE PLAN 6 H.S.
22 BAR DIA.
DETAIL "A"
1/4 4
C.L. PIER COLUMN COLUMN 2-L6X4X3/8X0'-8" (LLV) W/
SEE PLAN SEE PLAN 3/4" DIA. THRU-BOLT
3/16 IN 3" SLOTTED HOLES.
MAPLE TERRACE
DETAIL "A" FINGER-TIGHTEN NUT, 3001 MAPLE AVENUE
4" ELEVATION DALLAS, TEXAS, 75201
BACK OFF 1/4 TURN,
STEP IN GRADE BEAM OR WALL
& TACK WELD TYPICAL FOUNDATION DETAILS
SUMP PIT SECTION .016
TYPICAL DETAIL
TYPICAL DETAIL 16 17 18 20
NO SCALE
NO SCALE
1" = 1'-0" 1" = 1'-0"
190013
PROJECT NUMBER
NOTE:
NOTE: EXTEND THE BEAM REINF.
SEE PLAN SEE 1/S305-OF FOR INTO PUMP HANDLES IN
INFO. NOT SHOWN CURTAIN WALL
SEE PLAN SEE PLAN ADJACENT SPAN.
WALL REINF.: NOTE: SEE PLAN
ADD'L #5 X 10'-0" @ 12" SEE PLAN
#7 @ 12" VERT. E.F. SEE 3/S222-OF FOR BASEMENT WALL
RETENTION AND WHERE BASEMENT WALL IS
#4@10" HORIZ. E.F. SEE PLAN DWL.-B @ 12"
BACKFILL INFORMATION SEE PLAN PARALLEL TO SLAB SPAN
W/ 1#4 X CONT.
OPTIONAL C.J.
T.O.S.C. EL. SLAB-ON-VOID SLAB-ON-VOID
WATERSTOP SEE PLAN SITEWORK
SEE PLAN 3#8 X CONT. TOP SEE PLAN DEVELOPER
SEE SPECS SEE CIVIL/LANDSCAPE
RETENTION SYSTEM OPTIONAL C.J. Hines
3'-0"
SEE PLAN SEE 1/S305-OF FOR T.O.S.C. EL. 2200 Ross Avenue, Suite 4200W
1'-0" T.O.S.C. EL. =
SLAB THK.
WALL REINF. Dallas, TX 75201
SEE PLAN
SCHED.
#5 @ 12" 3'-0"
SEE PLAN (972-716-2908 Corbin Eckel)
8"
T.O.S.C. EL. 2800 Post Oak Blvd., 49th Floor
T.O.S.C. EL. Houston, TX 77056
6" MIN.
SEE PLAN (713-621-8000 Juan Delgado)
SEE PLAN
6"
SCHED. SLAB
#5X @12
1`-0"
DEPTH
EQUITY PARTNERS
2'-0"
McNair Interests
3'-0"
RETENTION SYSTEM Houston, TX 77024
SEE PLAN 4'-0" E.J. (Drew Steffen)
SEE PLAN
4'-0"
T.O. PIER #5 X @ 12" Mitsui Fudosan America
EL. RETENTION
SYSTEM #4@10" HORIZ. 1251 Avenue of the Americas, Suite 800
SEE PLAN
(David Leff)
3#8 X CONT. 1'-2" 1'-6" SEE 1/S305-OF FOR BASEMENT WALL INSIDE FACE T.O. PIER EL.
BOT. VERT. WALL REINF. SEE LOWER LEVELS GARAGE STRUCTURE
AND RETENTION SYSTEM,
FOR REINF. 5G Studio Collaborative, LLC.
#7@10" HORIZ. SEE RESIDENTIAL TOWER BEAM REINF:
1'-4" 1217 Main St., Suite 500
GARAGE DRAWINGS 3#9 TOP & BOT. Dallas, TX 75202
#4 X AS SHOWN @12" #4 STIR. @ 12" (214-347-4982 Christine Robbins-Elrod)
1'-0"
3/4" = 1'-0" 1 T.O.S.C. EL. 3/4" = 1'-0" 3 3/4" = 1'-0" 4 SEE PLAN
3/4" = 1'-0" 5 GFF Architects
SEE PLAN 1" SEE PLAN Dallas, TX 75201
T.O. PIER EL. ZONING/ENTITLEMENT

NOTE:
SEE 4/S305-OF FOR SEE PLAN Baldwin Associates
INFO. NOT SHOWN. Dallas, TX 75226
SEE 6/S304-OF FOR
ELEVATOR PIT SLAB (214-824-7949 Robert Baldwin)
COLUMN
INFO. NOT SHOWN SEE PLAN
SEE PLAN
ADDN'L. #5X10'-0"
@12" TOP
3/4" = 1'-0" 2 SLAB-ON-VOID
SEE PLAN
GEOTECH
ECS Southwest, LLP
E.J. DWL-B 3033 Kellyway Drive, Suite 110
WHERE BASEMENT
NOTE: SEE PLAN W/ 1#4 CONT. Carrollton, TX 75006
WALL IS PARALLEL TO
SLAB SPAN SEE 8/S305-OF FOR (972-392-3222 Siddharth Neekhra)
DWL.-B@12" INFO. NOT SHOWN.
SLAB-ON-VOID T.O.S.C. EL.
SEE PLAN W#4 CONT. CIVIL ENGINEER
SLAB SEE PLAN
SLAB-ON-VOID Kimley-Horn and Associates, Inc.
SEE PLAN SLAB-ON-VOID SEE SCHED. DWL.-B @ 12" 13455 Noel Road, Two Galleria Office Tower, Suite 700
SEE PLAN
SEE PLAN SLAB REBAR W/ 1#4 X CONT. Dallas, TX 75240
T.O.S.C. EL. T.O.S.C. EL.
SEE PLAN T.O.S.C. EL.
SEE PLAN SEE PLAN LANDSCAPE ARCHITECT
8"
SWA Group
SCHED.
DEPTH
8/S305-OF Dallas, TX 75207

STRUCTURAL
OPTIONAL C.J. Datum Engineers
RETENTION SYSTEM 6516 Forest Park Road
3'-0"
EXISTING WATER PROOFING T.O. PIER EL. (214-358-0174 Rodolfo D'Arlach)
BEAM REINF.: BASEMENT WALL SEE ARCH'L
BASEMENT WALL 4#9 TOP & BOT. MEP ENGINEER
SEE LOWER LEVELS #4 STIR. @10" O.C. ME Engineers, Inc.
FOR REINF. 1825 Market Center Blvd., Suite 600
T.O. PIER EL. PIER Dallas, TX 75207
T.O. PIER EL. SEE PLAN (214-741-1589 Drew Shivley)
BEAM REINF: ELEVATOR CONSULTANT

4#9 TOP & BOT. Persohn | Hahn Associates, Inc.
#4 STIR. @ 10" 8612 Broad Meadow Lane
McKinney, TX 75071
2'-0" (972-832-4232 Tom Williams)
3/4" = 1'-0" 6 3/4" = 1'-0" 7 3/4" = 1'-0" 8 3/4" = 1'-0" 10 INTERIOR DESIGNER
Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
SEE PLAN SEE PLAN

SEE PLAN
#4X3'-0"@12"
3'-0"
SMOOTH DWL. IN
1'-6"
FINISH REINF.
SEE PLAN 2" GREASED CUP 6#9 E.F. #4 X @ 12" www.datumengineers.com | Co. Reg. No. F-2819
SEE PLAN SEE ARCH'L W#4 X CONT. Dallas Austin San Antonio
3'-0" NOTE: 1'-0" #4 STIR 4-LEGGED @5" 214-358-0174 512-469-9490 210-858-2880
GARAGE E.J. SEE 3/S222-OF FOR (EXTEND HORIZ. BARS 78 BAR
1'-6"
ADDN'L #4 X 8'-0" @ 12" TOP SLAB ON GRADE Datum Project No. 19166
STRUCTURE SEE PLAN #4 DWL. @12" RETENTION AND DIA PAST OPENING) SEE PLAN DATE ISSUE TITLE
SEE RESIDENTIAL W/#4 CONT. BACKFILL INFORMATION 1'-0" HOOK THEM AROUND CORNERS
OPTIONAL C.J. #5@6" TOP & BOT 04/03/2020 SCHEMATIC DESIGN PRESENTATION
@ DISCONTINUOUS ENDS
78 BAR DIA.
TOWER GARAGE
DRAWINGS SLAB-ON-GRADE T.O.S.C. EL. 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
1'-0" T.O.S.C. EL.
SLAB THK.
SEE PLAN T.O.S.C. EL. SEE PLAN 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
SCHED.
3'-0" SEE PLAN 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT

SEE PLAN
4"
8"
8"
T.O.S.C. EL.
T.O.S.C. EL. 12/18/2020 90% CONSTRUCTION DOCUMENTS
2'-0"
SEE PLAN OPTIONAL C.J.
SEE PLAN OPTIONAL C.J.
8"
#5X @12
2'-0"

RETENTION SYSTEM
2'-6"
SEE PLAN
2'-6"
BEAM REINF.
RETENTION SYSTEM 4#8 TOP & BOT.
SEE PLAN #4 STIR. @ 12" PROVIDE 78 BAR DIA. LAP
1'-6"
W/ ELEVATOR PIT WALL
RETENTION SYSTEM EXTEND BARS & TOP BARS
SEE PLAN 2'-0" HOOK AT GRID 7
BASEMENT WALL BEAM
SEE LOWER LEVEL SEE 16/S305 ADDN'L #4 X @ 8"
FOR REINF. W/ 6#10 X CONT. BASEMENT WALL
1'-2" SEE 14/S305-OF SEE LOWER LEVEL
FOR REINF. 1'-2" FOR REINF.
3/4" = 1'-0" 11 3/4" = 1'-0" 12 3/4" = 1'-0" 13 3/4" = 1'-0" 14 3/4" = 1'-0" 15
GARAGE STRUCTURE
SEE RESIDENTIAL TOWER
E.J. GARAGE DRAWINGS AND
TENSION LAP SPLICE

SEE PLAN SEE PLAN RETENSION SYSTEM E.J
SEE PLAN SEE SEE PLAN
SEE S401-OF
DWL.-B@12"
W/#4 X CONT. PLAN
SEE SCHED.
SEE PLAN
SPLICE
SLAB ON VOID COLUMN BUNDLE DIAGONAL BARS
SEE PLAN T.O.S.C. EL. SEE PLAN PER 17/S305-OF
. CENTER ON
3'-0" SEE PLAN THIS DIAGONAL LINE
1'-6"
#4 DWL. @12" SLAB ON VOID WORK POINT FOR 17 COLUMN

ADDN'L #4 X 8'-0" @ 12" TOP W/#4 CONT. SEE PLAN DIAGONAL LINE SEE PLAN
EXIST. CONC.
4" 4"
S305-OF
WALL & SLAB
T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL.

8"
6"
5'-6" (F.V.)
78 BAR DIA.
5'-0"
2'-0"
6'-2"
4" TYP.
6'-2"
6"
T.O. PIER EL. BEAM REINF.
12#9 TOP EXISTING FOOTING. FIELD
BEAM REINF. VERIFY SIZE, DEPTH,
(2 LAYERS - 6 IN EA. LAYER) WORK POINT FOR
4#8 TOP & BOT. THICKNESS AND LOCATION F/S401-OF
5#5 INTERM. E.F. 3'-0" (F.V.) DIAGONAL LINE
#4 STIR. @ 12" PRIOR TO BEGINNING PIER MATCH BEAM
12#9 BOT. T.O.S.C. EL.
UNDERPINNING WORK SEE PLAN BOTOM BARS
(2 LAYERS - 6 IN EA. LAYER) SEE PLAN
PIER MAPLE TERRACE
TENSION LAP SPLICE

#4 STIR. @12" (6 LEGS)
2'-0" EXISTING FOOTING. SEE PLAN 3001 MAPLE AVENUE
SEE S401-OF
8#9 DIA.BARS HOOKED FIELD VERIFY SIZE, EQ. EQ. DALLAS, TEXAS, 75201
@ BOTH ENDS. RETENTION DEPTH, THICKNESS
SYSTEM FOUNDATION SECTIONS AND
4" 4"
SEE 20/S305-OF AND LOCATION PRIOR

SEE PLAN SEE PLAN
TO BEGINNING WORK
T.O. PIER EL. DETAILS
3/4" = 1'-0" 18 20
3/4" = 1'-0" 16 4'-0" 3/4" = 1'-0" 17 1/4" = 1'-0"
190013
PROJECT NUMBER
SLAB
EXIST. CONC. WALL SEE PLAN E.J.
& SLAB SEE PLAN
BASEMENT WALL
SEE PLAN EXIST. CONC. BEAM
& WALL
EXIST. T.O.S.C. EL. SLAB ON VOID

SEE PLAN SEE PLAN SEE PLAN SEE PLAN
E.J. DEVELOPER
SEE PLAN Hines
T.O.S.C. EL. Dallas, TX 75201
EXIST. T.O.S.C. EL. 2800 Post Oak Blvd., 49th Floor

SEE PLAN Houston, TX 77056
2 ADDN'L #6X10'0" (713-621-8000 Juan Delgado)
W/STANDARD HOOKS AT
COLUMN ENDS AT TOP & BOT.
EQUITY PARTNERS
SEE PLAN
McNair Interests
EXIST. CONC. WALL 109 N. Post Oak Lane, Suite 600
& SLAB EXISTING FOOTING. FIELD VERIFY
RETENTION Houston, TX 77024
SIZE, DEPTH, THICKNESS AND
EXISTING FOOTING SYSTEM (Drew Steffen)
LOCATION PRIOR TO BEGINNING
UNDERPINNING WORK BEYOND. FIELD VERIFY
SIZE, DEPTH, THICKNESS Mitsui Fudosan America
AND LOCATION PRIOR New York, New York 10020
TO BEGINNING (David Leff)
UNDERPINNING WORK
T.O.S.C. EL. 1217 Main St., Suite 500
EXIST. T.O.S.C. EL.
GFF Architects
RETENTION Dallas, TX 75201
SYSTEM 3/4" = 1'-0" 4 3/4" = 1'-0" 5 (214-303-1500 Michael Reyes)
ZONING/ENTITLEMENT
Baldwin Associates
Dallas, TX 75226
GEOTECH
E.J. ECS Southwest, LLP
SEE PLAN 3033 Kellyway Drive, Suite 110
EXIST. CONC.
WALL & SLAB CIVIL ENGINEER
Dallas, TX 75240
EXIST. T.O.S.C. EL. (972-770-1300 Alex Rathbun)
SEE PLAN
SLAB-ON-GRADE LANDSCAPE ARCHITECT
SEE PLAN
SWA Group
BEAM T.O.S.C. EL. Dallas, TX 75207
SEE PLAN EXISTING FOOTING. FIELD (214-954-0016 Chuck McDaniel)
VERIFY SIZE, DEPTH, SEE PLAN
THICKNESS AND LOCATION STRUCTURAL
PRIOR TO BEGINNING Datum Engineers
UNDERPINNING WORK 6516 Forest Park Road
Dallas, TX 75235
RETENTION PIER (214-358-0174 Rodolfo D'Arlach)
SYSTEM SEE PLAN 20U/S303-OF
MEP ENGINEER
ME Engineers, Inc.
SEE 3/S222-OF FOR (214-741-1589 Drew Shivley)
RETENTION AND
BACKFILL INFORMATION ELEVATOR CONSULTANT
McKinney, TX 75071
RETENTION
3/4" = 1'-0" 7 SYSTEM
3/4" = 1'-0" 10 INTERIOR DESIGNER
Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
E.J. E.J.
SEE PLAN BUILT UP SLAB 0N SEE PLAN EXIST. CONC. SEE PLAN
NEW OPENING IN EXISTING
STYROFOAM WALL & SLAB BASEMENT WALL
EXIST. CONC. SEE PLAN AND 17/S307-OF ADDN'L #5 X 10'-0" TOP
SEE PLAN AND ELEVATION
WALL & SLAB ADDN'L #5 X 10'-0" TOP Dallas Austin San Antonio
SLAB-ON-GRADE SLAB-ON-GRADE 4'-0" 214-358-0174 512-469-9490 210-858-2880
SEE PLAN
4'-0"
EXIST. T.O.S.C. EL. SEE PLAN 4'-0" Datum Project No. 19166
SLAB-ON-GRADE #5 x @ 12"
4'-0"
SEE PLAN
DWL.-B@12" SLAB-ON-VOID #5 x @ 12" SEE PLAN W/#4 CONT. DATE ISSUE TITLE
EXIST. T.O.S.C. EL. T.O.S.C. EL. SEE PLAN W/#4 CONT. 04/03/2020 SCHEMATIC DESIGN PRESENTATION
SEE PLAN W/#4 CONT.
SEE PLAN
EXISTING FOOTING. FIELD T.O.S.C. EL. T.O.S.C. EL. 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
VERIFY SIZE, DEPTH, SEE PLAN SEE PLAN
T.O.S.C. EL. THICKNESS AND LOCATION
SEE PLAN NOTE: 12/18/2020 90% CONSTRUCTION DOCUMENTS
PRIOR TO BEGINNING
SEE 3/S222-OF FOR 01/25/2021 100% CONSTRUCTION DOCUMENTS
UNDERPINNING WORK
SEE SCHED.
RETENTION AND
1'-6"
20U/S303-OF BACKFILL INFORMATION

EXISTING FOOTING. FIELD VERIFY SLAB-ON-GRADE RESERVED FOR REVIEWERS NOTES
SIZE, DEPTH, THICKNESS AND SEE PLAN
LOCATION PRIOR TO BEGINNING RETENTION
UNDERPINNING WORK SYSTEM
BASEMENT WALL BASEMENT WALL

SEE LOWER LEVEL SEE LOWER LEVEL
BASEMENT WALL
NOTE: FOR REINF. FOR REINF.
SEE LOWER LEVEL
SEE 3/S222-OF FOR FOR REINF.
RETENTION AND ELEVATOR
BACKFILL INFORMATION SHAFT
3/4" = 1'-0" 12 RETENTION

SYSTEM 3/4" = 1'-0" 13 3/4" = 1'-0" 14 3/4" = 1'-0" 15
NOTE:
SEE 13/S305-OF FOR
INFO. NOT SHOWN.
SEE PLAN
SEE PLAN SEE PLAN E.J.
SEE PLAN
WALL REINF.: SEE PLAN
#7 @ 12" VERT. E.F.
WALL REINF.:
#4@12" HORIZ. E.F.
#7 @ 12" VERT. E.F.
FINISH
#4@12" HORIZ. E.F.
SEE ARCH'L EXISTING BASEMENT WALL OPTIONAL C.J.
SEE PLAN 1'-0"
SLAB THK.
SLAB-ON-GRADE
SCHED.
SEE SCHED.
OPTIONAL C.J. SEE PLAN SLAB REBAR
WATERSTOP
T.O.S.C. EL. RETENTION SYSTEM SEE SPECS
3'-0"
T.O.S.C. EL. EXIST. T.O.S.C. EL. SEE PLAN
SEE PLAN
SEE PLAN SEE PLAN
T.O.S.C. EL. #5 @ 12"
SEE PLAN
T.O.S.C. EL.
78 BAR DIA.
SEE PLAN
6"
RETENTION SYSTEM
2'-6"
1`-0"
SEE PLAN
RETENTION SYSTEM
SEE PLAN
2'-0"
20U/S303-OF
BASEMENT WALL
T.O. PIER EL. MAPLE TERRACE
SEE LOWER LEVEL
1'-2" FOR REINF.
3001 MAPLE AVENUE
3#8 X CONT. 1'-0" 1'-6" FOUNDATION SECTIONS AND
BOT.
DETAILS
16 17
3/4" = 1'-0" 3/4" = 1'-0"
3/4" = 1'-0" 18 3/4" = 1'-0" 19 190013
PROJECT NUMBER
CURTAIN WALL
SEE PLAN NOTE:
SEE 17/S305-OF FOR
CURTAIN WALL SEE PLAN
E.J. SEE PLAN DWL-B@12" O.C.
SEE PLAN SLAB-ON-VOID W/ #4 CONT.
SEE PLAN
SEE PLAN SEE PLAN
SITEWORK
SEE CIVIL/LANDSCAPE SLAB
SITEWORK SEE PLAN
T.O.S.C. EL. SEE CIVIL/LANDSCAPE
SEE PLAN SEE PLAN DEVELOPER
8"
T.O.S.C. EL. SLAB
SCHED. DEPTH
Hines
SEE PLAN E.J. SLAB SEE PLAN 2200 Ross Avenue, Suite 4200W
SCHED. DEPTH
SEE PLAN SEE PLAN Dallas, TX 75201
E.J. (972-716-2908 Corbin Eckel)
SEE PLAN J/S401-OF
SEE PLAN
T.O.S.C. EL. T.O.S.C. EL. Houston, TX 77056
T.O.S.C. EL. (713-621-8000 Juan Delgado)
SEE PLAN SEE PLAN
SCHED. DEPTH
SEE PLAN
SCHED. DEPTH
LEVEL 1 EQUITY PARTNERS
0' - 0" McNair Interests
SCHED. DEPTH
6'-2"
Houston, TX 77024
SEE PLAN BEAM (Drew Steffen)
SEE PLAN Level 1A
SEE GARAGE SCHED. WIDTH -0' - 11" Mitsui Fudosan America
DRAWINGS FOR 4'-0" BEAM SCHED. WIDTH 1251 Avenue of the Americas, Suite 800
RETENTION SYSTEM SEE PLAN New York, New York 10020
AND GARAGE WALLS GARAGE STRUCTURE EXISTING (David Leff)
SEE RESIDENTIAL BASEMENT WALL BEAM
TOWER GARAGE SEE PLAN OFFICE/RETAIL ARCHITECT
DRAWINGS EXISTING 5G Studio Collaborative, LLC.
BASEMENT WALL 1217 Main St., Suite 500
COLUMN
Dallas, TX 75202
SEE PLAN
E.J. E.J.
SEE PLAN SEE PLAN
T.O. PIER EL. MASTER/MULTIFAMILY ARCHITECT
3/4" = 1'-0" 1 3/4" = 1'-0" 2 3/4" = 1'-0" 3 3/4" = 1'-0" 4 3/4" = 1'-0" 5 GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
SEE PLAN SEE PLAN 3904 Elm Street, Suite B
4'-0" Dallas, TX 75226
4'-0"
4'-0" SEE PLAN (214-824-7949 Robert Baldwin)
#5 x @ 12"
4'-0"
#5 x @ 12" W/#4 CONT.

SEE PLAN GEOTECH
W/#4 CONT. ECS Southwest, LLP
E.J. SLAB SLAB-ON-VOID SEE PLAN 3033 Kellyway Drive, Suite 110
SLAB ON VOID SEE PLAN SEE PLAN SEE PLAN Carrollton, TX 75006
SCHED.

DEPTH
SEE PLAN
CIVIL ENGINEER
T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL. =
SEE PLAN SEE PLAN SEE PLAN 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
SCHED.
DEPTH
LANDSCAPE ARCHITECT
ELEVATOR SHAFT SWA Group
Dallas, TX 75207
BEAM BEYOND BASEMENT WALL
BASEMENT WALL EXISTING SEE PLAN BEAM SEE LOWER LEVEL
SEE LOWER LEVEL STRUCTURAL
BASEMENT WALL SEE PLAN TEMPORARY FOR REINF.
FOR REINF. Datum Engineers
RETENTION SYSTEM 6516 Forest Park Road
TEMPORARY (214-358-0174 Rodolfo D'Arlach)
RETENTION SYSTEM
SEE PLAN MEP ENGINEER
ME Engineers, Inc.
Dallas, TX 75207
ELEVATOR CONSULTANT
3/4" = 1'-0" 6 3/4" = 1'-0" 9 3/4" = 1'-0" 10 Persohn | Hahn Associates, Inc.
McKinney, TX 75071
INTERIOR DESIGNER
Rottet Studio
4'-0" 808 Travis Street, Suite 100
4'-0"
Houston, TX 77002
#5 x @ 12"
(713-221-1830 x 6105 Anja Majkic)
W/#4 CONT.
E.J. 1
E.J. SLAB-ON-VOID NEW OPENING IN EXISTING
SEE PLAN SEE PLAN SEE PLAN DWL.-B @ 12" SEE PLAN BASEMENT WALL
S307-OF
W/ 1#4 X CONT. SEE PLAN AND ELEVATION
COLUMN WORK POINT FOR www.datumengineers.com | Co. Reg. No. F-2819
SEE PLAN DIAGONAL LINE T.O.S.C. EL. EXIST. CONC. Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
SEE PLAN WALL & SLAB Datum Project No. 19166
8"
SLAB SLAB-ON-GRADE
DATE ISSUE TITLE
SEE PLAN SEE PLAN
2'-5"
T.O.S.C. EL. T.O.S.C. EL. 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
SEE PLAN Level 1B SEE PLAN Level 1B 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
-9' - 8" -9' - 8" 10/30/2020 ISSUE FOR PERMIT
SCHED.
3'-0"
DEPTH
EXISTING FOOTING.
GARAGE STRUCTURE 1" E.J. FIELD VERIFY SIZE,
SEE RESIDENTIAL TOWER DEPTH, THICKNESS AND RESERVED FOR REVIEWERS NOTES
GARAGE DRAWINGS WORK POINT FOR 78 BAR DIA.
DIAGONAL LINE LOCATION PRIOR TO 20U/S303-OF
BEGINNING WORK ADDN'L 6#7 T.O. PIER EL.
PIER PROVIDE TENSION LAPS
PIER MATCH BEAM BOTTOM BARS
SEE PLAN EXTEND 78 BAR DIA. INTO
SEE PLAN SHEAR WALL BEAM REINF:
3#7 TOP & BOT.
#4 STIR. @ 12"
EQ. EQ. 1'-6" PROVIDE TENSION LAPS
EXTEND 78 BAR DIA. INTO
SHEAR WALL
27'-4" 5'-0"
3/4" = 1'-0" 11 1/4" = 1'-0" 13 3/4" = 1'-0" 14 3/4" = 1'-0" 15

.05
0 12/18/2020 Permit Set Update
1 02/09/2021 ADDENDUM 1
4" NWT. CONCRETE

REINF. W/ #4@12 E.W.
REVOLVING DOOR
CENTERED IN SLAB
SEE ARCH'L
SEE PLAN
REMOVE EXISTING SLAB 2'-0"
TO FORM 1" X SLAB DOW STYROFOAM BLOCK
DEPTH X CONT. KEY #4 X @ 12" W/ 40 PSI COMPRESSIVE 2'-0" 4'-0"
STRENGTH, CUT AS REQ'D ARDEX ERM RAMP
#3X3'-0" @ 1'-6" STYROFOAM SHALL BE MORTAR OR APPROVED
#4@12" E.W.. EQUAL.INSTALL PER MFR.
DWL-C@12" LEVELED TO WITHIN 1/4" OF
INTENDED ELEVATION RECOMMENDATIONS 17/S307-OF
#3@12 E.W.
SITEWORK PROVIDE STEM WALL T.O.S.C. EL.
SEE CIVIL AT PERIMETER SEE PLAN ROUGHEN SURFACE
1" 19/S613-OF
12"
1/2"
#3 X @ 1'-6" SLOPE T.O.S.C. EL.

SEE PLAN
6"
2" 6" STRUCTURAL

STYROFOAM
MAPLE TERRACE
12/S613-OF
3001 MAPLE AVENUE
SIM. DALLAS, TEXAS, 75201
EXISTING BUILDING 1 1 FOUNDATION SECTIONS AND
3/S613-OF
DETAILS
16 3/4" = 1'-0" 17 18 19 20
SEE PLAN 3/4" = 1'-0" 3/4" = 1'-0"
190013
PROJECT NUMBER
CONCRETE COLUMN SCHEDULE SCHEDULE NOTES:
1. SEE DETAILS B/S401-OF THRU F/S401-OF FOR TYPICAL BAR SPLICE
COLUMN MARKS CONDITIONS.
PENTHOUSE ROOF C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13
COLUMN SIZE (INCHES) 14x14 14x14 14x14 2. ALL COLUMN BAR SPLICES ARE TO BE IN ACCORDANCE WITH "SPLICE
REINFORCING 4#7(L) 1#7(S) 4#7(L) 1#7(S) 8#7 SCHEDULE T" UNLESS NOTED OTHERWISE IN THE COLUMN SCHEDULE.
WHEN A REFERENCE TO A PARTICULAR SPLICE SCHEDULE IS PROVIDED IN
SPLICE SCHEDULE THE COLUMN SCHEDULE, IT APPLIES TO THE SPLICE REQUIRED WITH THE
ROOF DETAIL J/S401-OF J/S401-OF J/S401-OF BARS IN THE COLUMN ABOVE, AS SHOWN IN DETAIL C/S401-OF. SEE S302-OF
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 14x14 FOR PIER DOWEL SPLICES.
REINFORCING 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 12#7 4#7(L) 1#7(S) 8#7 8#7 8#7 DEVELOPER
3. LAP SPLICE LENGTHS ARE TO BE CALCULATED BASED ON THE SMALLER
Hines
SPLICE SCHEDULE T T T BAR BEING LAPPED. 2200 Ross Avenue, Suite 4200W
LEVEL 9 DETAIL J/S401-OF J/S401-OF J/S401-OF J/S401-OF D/S401-OF D/S401-OF J/S401-OF J/S401-OF J/S401-OF J/S401-OF J/S401-OF Dallas, TX 75201
4. ALL COLUMN BAR SPLICES IN COLUMNS WHERE THE AREA OF (972-716-2908 Corbin Eckel)
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 14x14 REINFORCING DIVIDED BY THE AREA OF THE COLUMN CROSS SECTION IS
REINFORCING 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 12#7 4#7(L) 1#7(S) 8#7 8#7 8#7 GREATER THAN .04 (4%) SHALL BE MECHANICAL SPLICES SINCE CODE DOES 2800 Post Oak Blvd., 49th Floor
NOT ALLOW MORE THAN 8%. Houston, TX 77056
SPLICE SCHEDULE C C C C C C C C C C T
LEVEL 8 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF
5. SPLICE ALL COLUMN BARS AT EACH FLOOR/COLUMN INTERSECTION. DO
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 NOT SPLICE COLUMN BARS BETWEEN FLOOR/COLUMN INTERSECTIONS EQUITY PARTNERS
REINFORCING 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 12#7 4#7(L) 1#7(S) 8#7 8#7 EVEN IF THE COLUMN SPANS ACROSS MORE THAN ONE LEVEL WITHOUT McNair Interests
ACTUALLY INTERSECTING WITH THE FLOOR FRAMING. 109 N. Post Oak Lane, Suite 600
SPLICE SCHEDULE C C C C C C C C C C Houston, TX 77024
LEVEL 7 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF 6. WHERE VERTICAL BARS ARE OFFSET AT A SPLICE, THE SLOPE OF THE (Drew Steffen)
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 INCLINED PORTION OF THE BAR WITH THE AXIS OF THE COLUMN SHALL NOT Mitsui Fudosan America
REINFORCING 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 12#7 4#7(L) 1#7(S) 8#7 8#7 EXCEED 1 IN 6, AND 3 ADDITIONAL TIES SHALL BE ADDED TO THE TOP OF 1251 Avenue of the Americas, Suite 800
THE COLUMN CENTERED ON THE BEND. SEE DETAIL C/S401-OF. New York, New York 10020
SPLICE SCHEDULE C C CONT. C C C C C C C (David Leff)
LEVEL 6 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF 7. OFFSET LAPPED BARS IN A PLANE NORMAL TO THE TIE. SEE DETAIL SEE
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 DETAIL B/S401-OF. OFFICE/RETAIL ARCHITECT
L 5G Studio Collaborative, LLC.
REINFORCING 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 4#7(L) 1#7(S) 4#7(L) 1#7(S) 12#7 4#7(L) 1#7(S) 8#7 8#7 8. IN SQUARE COLUMNS EQUALLY DISTRIBUTE THE SCHEDULED 1217 Main St., Suite 500
SPLICE SCHEDULE C CONT. CONT. C C C C C C C REINFORCMENT TO EACH FACE. IN ROUND COLUMNS EQUALLY S Dallas, TX 75202
DISTRIBUTE SCHEDULED REINFORCEMENT AROUND PERIMETER (214-347-4982 Christine Robbins-Elrod)
LEVEL 5 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF
OF COLUMN. IN RECTANGULAR COLUMNS, THE LETTER "L"
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 ASSOCIATED WITH THE SCHEDULED COLUMN REINFORCMENT MASTER/MULTIFAMILY ARCHITECT
REINFORCING 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 12#8 4#8(L) 1#8(S) 8#8 8#8 INDICATES THE NUMBER OF BARS REQUIRED ON EACH LONG FACE GFF Architects
SPLICE SCHEDULE C C C C C C C C C C AND THE LETTER "S" INDICATES THE NUMBER OF BARS REGUIRED 2808 Fairmount St., Suite 300
ON EACH SHORT FACE. Dallas, TX 75201
LEVEL 4 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF (214-303-1500 Michael Reyes)
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 9. PLAN EAST-WEST DIMENSIONS ARE GIVEN FIRST IN COLUMN SCHEDULE.
ZONING/ENTITLEMENT
REINFORCING 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 12#8 4#8(L) 1#8(S) 8#8 8#8
Baldwin Associates
SPLICE SCHEDULE CONT. CONT. CONT. C C C C C C C 3904 Elm Street, Suite B
LEVEL 3 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF Dallas, TX 75226
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 SPLICE SCHEDULE (C) (214-824-7949 Robert Baldwin)
REINFORCING 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 4#8(L) 1#8(S) 4#8(L) 1#8(S) 12#9 4#8(L) 1#8(S) 8#8 8#8 COMPRESSION SPLICE SPLICE SCHEDULE (T) FOR 75 KSI REINF. GEOTECH
SPLICE SCHEDULE C C C C C C C C C C (CLASS B) ECS Southwest, LLP
BAR SIZE SPLICE LENGTH 3033 Kellyway Drive, Suite 110
LEVEL 2 DETAIL C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF (LENGTHS IN INCHES) Carrollton, TX 75006
COLUMN SIZE (INCHES) 18X28 18X28 18X28 18x28 18x28 28x18 18x18 28x18 18x18 18x18 #3-#6 30 BAR DIA. LAP (972-392-3222 Siddharth Neekhra)
REINFORCING
SPLICE SCHEDULE
4#9(L) 1#9(S)
CONT.
4#9(L) 1#9(S)
CONT.
4#9(L) 1#9(S)
CONT.
4#9(L), 1#9(S)
C
4#8(L) 1#8(S)
C
4#8(L) 1#8(S)
C
12#9
C
4#8(L) 1#8(S)
C
8#8
C
8#8
C
#7-#11 44 BAR DIA. LAP CONCRETE STRENGTH CIVIL ENGINEER
LEVEL 1 DETAIL - C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF #14&#18 & SMALLER MECHANICAL SPLICE BAR SIZE 3000 4000 5000 6000 13455 Noel Road, Two Galleria Office Tower, Suite 700
- 18X28 18X28 14X14 18x28 28x18 18x18 18x18 BARS THAT SPLICE W/ Dallas, TX 75240
COLUMN SIZE (INCHES) (972-770-1300 Alex Rathbun)
A #14 OR #18
REINFORCING - 4#9(L), 1#9(S) 4#9(L), 1#9(S) 8#8 4#9(L) 1#9(S) 4#9(L) 1#9(S) 8#9 8#8
#4 29 25 23 21 LANDSCAPE ARCHITECT
LEVEL B1 SPLICE SCHEDULE - C C C C C C
DETAIL - C/S401-OF C/S401-OF J/S401-OF C/S401-OF C/S401-OF C/S401-OF C/S401-OF #5 36 31 28 26 SWA Group
COLUMN SIZE (INCHES) - - 18X28 18x28 28x18 18x18 #6 43 37 34 31 Dallas, TX 75207
REINFORCING - - 4#9(L), 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 8#9 (214-954-0016 Chuck McDaniel)
SPLICE SCHEDULE - - C C C C #7 (75 GR.) 79 68 61 56

LEVEL B2 STRUCTURAL
DETAIL - - C/S401-OF C/S401-OF C/S401-OF C/S401-OF #8 (75 GR.) 90 78 70 64 Datum Engineers
COLUMN SIZE (INCHES) - - 18X28 18x28 28x18 18x18 6516 Forest Park Road
#9 (75 GR.) 101 88 79 71 Dallas, TX 75235
REINFORCING - - 4#9(L), 1#9(S) 4#9(L) 1#9(S) 4#9(L) 1#9(S) 8#9 (214-358-0174 Rodolfo D'Arlach)
LEVEL B3 SPLICE SCHEDULE - - C C C C #10 (75 GR.) 114 99 89 80
DETAIL - - C/S401-OF C/S401-OF C/S401-OF C/S401-OF MEP ENGINEER
#11 (75 GR.) 126 109 98 89
ME Engineers, Inc.
DOWELS 10#9 10#9 10#9 8#8 10#10 10#9 10#9 12#9 10#8 8#9 8#8 1825 Market Center Blvd., Suite 600
#14 (75 GR.) MECHANICAL SPLICE
FOUNDATION SPLICE SCHEDULE C C C C C C C C C C C T T Dallas, TX 75207
DETAIL E/S302-OF E/S302-OF U.N.O. E/S302-OF D/S302-OF E/S302-OF SIM E/S302-OF E/S302-OF D/S302-OF D/S302-OF E/S302-OF E/S302-OF F/S401-OF F/S401-OF #18 (75 GR.) MECHANICAL SPLICE
NOTES SEE DETAIL F/S401-OF SEE DETAIL F/S401-OF SEE DETAIL F/S401-OF SEE DETAIL F/S401- ELEVATOR CONSULTANT
FOR COLUMN AT FOR COLUMN AT NOTE 5 FOR COLUMN AT OF AT ROOF AND BAR SPLICE SCHEDULES AND NOTES Persohn | Hahn Associates, Inc.
GRIDLINE C-14, SEE
NOTE 5
GRIDLINE C-1, SEE
NOTE 5
GRIDLINE B.5-1 PROVIDE (T) SPLICE A 8612 Broad Meadow Lane
McKinney, TX 75071
LESS 3" OR INTERIOR DESIGNER

COL SIZE
THAN 3"
SEE SCHED. REFER TO DETAIL B/S401-OF GREATER COL. SIZE
SEE SCHED.
TIE SPACING SCHEDULE Rottet Studio
FOR ARRANGEMENT OF REFER TO DETAIL B/S401-OF MIN.
COL. Houston, TX 77002
COLUMN BARS AT SPLICES FOR ARRANGEMENT OF (713-221-1830 x 6105 Anja Majkic)
COLUMN BARS AT SPLICES BAR
SEE COLUMN SCHEDULE MIN.
COL. DIM. #6 #7 #8 #9 #10 #11 #14 #18
DOWELS SAME SIZE AND
SCHED. (T), U.N.O.
BAR LAP SPLICE
10" 10"
NUMBER AS BARS
BAR LAP SPLICE

SEE SPLICE
5" CLEAR
SCHEDULE (T)
-SEE SPLICE
SCHEDULED FOR www.datumengineers.com | Co. Reg. No. F-2819
COLUMN 12" 12"
U.N.O.
STANDARD 90° HOOK Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
ABOVE FLOOR
14" 14"
3"

DATE ISSUE TITLE
T.O.S.C. EL. T.O.S.C. EL. 16" 16"
3" 3"
ROUND COLUMNS 04/03/2020 SCHEMATIC DESIGN PRESENTATION

18" 18" 18" 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT

SCHEDULE (T), U.N.O.

20" 20"
BAR LAP SPLICE
24" 22" 24" 24" 01/25/2021 100% CONSTRUCTION DOCUMENTS
CONTINUE TIES THRU FLOOR

BEND BARS AT 1:6 SLOPE OR ROOF FRAMING @ 3" O.C.
NOTE: INTO COLUMN ABOVE 28"
COLUMN BARS FROM TIES, SEE COLUMN
BELOW ARE OFFSET 3 ADDITIONAL TIES @ 3" O.C. 32" TIE PLACEMENT
INTO THE COLUMN CENTERED ON BEND DETAIL H/S401-OF
(SEE C/S401-OF ) NOTES:
TIES, SEE COLUMN 1. ROUND OFF ODD DIMENSIONS TO SMALLER SIZE IN TABLE.
TIES - SEE COLUMN TIE TIE PLACEMENT 2. SEE COLUMN SPLICE DETAILS FOR DIMENSIONS TO FIRST TIE.
COLUMN BAR ABOVE PLACEMENT DETAIL H/S401-OF DETAIL H/S401-OF 3. USE #4 TIES IF ANY VERTICAL BARS IN COLUMN ARE #11 OR LARGER. USE #3 TIES
OTHERWISE.
OFFSET
4. PLACE A COLUMN TIE 3" ABOVE THE TOP OF THE FOUNDATION OR INTERSECTING SLAB
SQUARE OR RECTANGULAR COLUMNS COLUMN BAR
AT ANY LEVEL AND 3" BELOW THE LOWEST HORIZONTAL REINFORCING IN THE SLAB OF
FROM BELOW
THE FLOOR OR ROOF FRAMING ABOVE AND SPACE TIES IN BETWEEN. WHERE BEAMS
LAP SPLICE - WHERE OFFSET DUE TO COLUMN SIZE FRAME FROM FOUR DIFFERENT DIRECTIONS INTO A COLUMN, TIES MAY BE TYPICAL COLUMN TERMINATION
BAR POSITIONING AT LAP SPLICE
B
TYPICAL LAP SPLICE - FOR SAME SIZE COLUMNS OR
WHERE OFFSET DUE TO COLUMN SIZE CHANGE IS LESS THAN 3" CHANGE IS 3" OR GREATER D TERMINATED WITHIN THE FLOOR FRAMING 3" BELOW THE LOWEST HORIZONTAL NO SCALE J
NO SCALE
NO SCALE C NO SCALE
REINFORCING IN THE SHALLOWEST BEAM.
NOTES FOR SQUARE AND RECTANGULAR COLUMNS: .05 12/18/2020 Permit Set Update
NOTE: 1. SIDE FACE BARS SHALL BE EQUALLY SPACED
ALTERNATE STAGGERED BETWEEN CORNER BARS. PROVIDE
SPLICES AROUND THE ADDITIONAL INTERIOR TIES ( ) AT
COLUMN SIZE PERIMETER OF THE COLUMN. ALTERNATE BARS. ALSO, PROVIDE INTERIOR
SEE SCHEDULE TIES WHENEVER CLEAR SPACING BETWEEN
SEE DETAIL B/S401-OF BARS EXCEEDS 6".
TIES, SEE COLUMN TIE
FOR ARRANGEMENT OF 2. USE SQUARE TIES FOR SIDE FACE BARS, IF
TIES, SEE COLUMN PLACEMENT DETAIL
COLUMN BARS AT SPLICE REQUIRED FOR TREMIE PLACEMENT.
TIE PLACEMENT
DETAIL H/S401-OF <_ 6" > 6"
SEE SPLICE SCHED. (T).
BAR LAP SPLICE
50 PER CENT OF COLUMN DOWELS TO

SCHEDULED BARS MATCH COLUMN
U.N.O.
REINFORCING, U.N.O.
MECHANICAL
> 6"
SPLICES, CADWELD
(C) SERIES STANDARD HOOK
STANDARD 90 DEGREE
2'-0" MIN.
125 PERCENT YIELD HOOKS STAGGERED

POINT SPLICE OR AROUND PERIMETER OF
3"
LENTON SPLICES COLUMN ENGAGING A

VERTICAL COLUMN BAR
1/4 COL.
HEIGHT
IN.
< 6"
5"
6" M
LAP
_
T.O.S.C. EL.
CONTINUE TIES THRU
FLOOR OR ROOF
FRAMING @ 3 db (OF
HOOKED BAR) O.C. SQUARE OR RECTANGULAR COLUMN ROUND COLUMN MAPLE TERRACE
3001 MAPLE AVENUE
LAP SPLICE - COLUMN BASE AT TRANSFER GIRDER COLUMN TIE PLACEMENT DETAIL
TYPICAL MECHANICAL SPLICE - REQUIRED FOR #14 & #18 BARS AND FOR
NO SCALE NO SCALE CONCRETE COLUMN SCHEDULE
COLUMNS WITH MORE THAN 4% REINFORCEMENT
F AND DETAILS
NO SCALE E COLUMN TIE PLACEMENT DETAIL H
TYPICAL COLUMN BAR SPLICING SCHEDULES AND DETAILS 190013
PROJECT NUMBER
CONSTRUCTION JOINT
WITHIN 2'-6" OF SLAB
MIDSPAN AT ELEVATED
SLABS
REINF. CONTINUOUS
THROUGH JOINT
DEVELOPER
1/3 "D"
Hines
Dallas, TX 75201
D
Houston, TX 77056
EQUITY PARTNERS
1 1/2" FOR "D" >/=8"
3/4" FOR "D" <8" McNair Interests
Houston, TX 77024
(Drew Steffen)

(David Leff)
Dallas, TX 75202
STRUCTURAL SLAB CONSTRUCTION JOINT
TYPICAL DETAIL B GFF Architects
NO SCALE Dallas, TX 75201
ZONING/ENTITLEMENT
CONCRETE SLAB SCHEDULE Baldwin Associates
Dallas, TX 75226
SLAB
SPA
EXTEND BARS FULL LENGTH
OF SPAN IN DIRECTION OF
SLAB TEMPERATURE SLAB
SLAB REINFORCEMENT
THICKNESS REMARKS GEOTECH

N
REINFORCING SCHEDULE MARK TOP BARS BOTTOM BARS TOP BARS TOP BARS
2'-6"
SLAB SPAN
MIN.
(IN.) LEFT END CENTER CENTER RIGHT END ECS Southwest, LLP
#5 x 4'-0" EACH FACE, EACH TOP LEFT BARS FROM TWO-
SLAB THICKNESS BOTTOM TEMP. REINF. TOP TEMP. REINF. S1 8 #5Z@24", #5Y@24" #5QQ@12" O.C. Carrollton, TX 75006
CORNER. PLACE INSIDE OF WAY SLAB SCHEDULE (972-392-3222 Siddharth Neekhra)
OTHER SLAB REINFORCING. TOP LEFT BARS FROM TWO-
S2 8 WAY SLAB SCHEDULE #5Z@24", #5Y@24"
1 1/2" 5" TO 7" #4 @ 15" NONE CIVIL ENGINEER
CLR. Kimley-Horn and Associates, Inc.
PROVIDE EXTRA BARS IN S3 8 #4X@10"O.C. #5L@10" O.C.
8" TO 9" #4 @ 12" NONE 13455 Noel Road, Two Galleria Office Tower, Suite 700
EACH LAYER, EQUAL TO AREA Dallas, TX 75240
OF INTERRUPTED BARS (1#5 S4 8 #4X@10"O.C. #6N@10"O.C. (972-770-1300 Alex Rathbun)
EACH FACE EACH SIDE 10" TO 11" #4 @ 10" NONE
MINIMUM). S5 8 #6X@10"O.C. #5N@12"O.C. LANDSCAPE ARCHITECT
12" #4 @ 18" #4 @ 18" SWA Group
EXTEND BOT. BARS TO 2001 Irving Boulevard, Suite 157
S6 8 #4X@10"O.C. #5N@10"O.C.
13" TO 14" #4 @ 15" #4 @ 15" EITHER ENDS OF CANT. Dallas, TX 75207
NOTE: EXTEND BOT. BARS TO (214-954-0016 Chuck McDaniel)
S7 10 #5Q@12"O.C. #6W@9"O.C. #5Q@12"O.C.
EXTRA BARS MAY BE OMITTED 15" TO 18" #4 @ 12" #4 @ 12" EITHER ENDS OF CANT.
WHERE SIDES OF OPENING STRUCTURAL
ARE FRAMED BY BEAMS. S8 8 #4Z@10"O.C. #4J@12"O.C. Datum Engineers
19" TO 21" #5 @ 16" #5 @ 16"
TYPICAL SLAB PLAN S9 8 #4B@24"O.C., #4E@24"O.C. #5Z@24"O.C., #5Y@24"O.C. #5A@24"O.C., #5H@24"O.C. Dallas, TX 75235
REINFORCING 22" TO 27" #5 @ 12" #5 @ 12" (214-358-0174 Rodolfo D'Arlach)
S10 8 #5Z@24"O.C., #5Y@24"O.C. #5A@14"O.C., #5H@14"O.C.

REINFORCING AT SLAB OPENING MEP ENGINEER
#5W@24"O.C., #5X@24"O.C. #5Q@12"O.C. ME Engineers, Inc.
NOTES:
TYPICAL DETAIL 1. TEMPERATURE REINFORCEMENT SHALL BE PROVIDED PERPENDICULAR TO
S11 8 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
NO SCALE THE MAIN REINFORCEMENT IN ALL ONE-WAY SLABS IN AT LEAST THE ABOVE S11A 8 #6Z@24"O.C., #6Y@24"O.C. #4B@24"O.C., #4E@24"O.C. (214-741-1589 Drew Shivley)
AMOUNTS. SUCH REINFORCEMENT SHALL BE EVENLY SPACED ACROSS THE
ENTIRE WIDTH OF SLAB AND SHALL BE PLACED IN TWO LAYERS IN SLABS 12" #4Z@24"O.C., #4Y@24"O.C. #4B@24"O.C., #4E@24"O.C. ELEVATOR CONSULTANT
S12 8
OR MORE IN THICKNESS. Persohn | Hahn Associates, Inc.
D 2. TEMPERATURE REINFORCEMENT SHALL BE TIED ABOVE SCHEDULED BOTTOM
REINFORCEMENT AND BELOW SCHEDULED TOP REINFORCEMENT.
E S13 8 #5B@8"O.C. #5Y@16"O.C., #5Z@16"O.C. #5B@8"O.C. 8612 Broad Meadow Lane
McKinney, TX 75071
S14 8 #5B@12"O.C. #5Y@24"O.C., #5Z@24"O.C. #5B@12"O.C.
INTERIOR DESIGNER
S15 8 #5A@9"O.C. #5Y@24"O.C., #5Z@24"O.C. #5B@12"O.C. Rottet Studio
S16 8 #4E@12"O.C. #4Z@24"O.C., #4Y@24"O.C. #4A@12"O.C. Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
S17 8 #4E@12"O.C. #5Y@24"O.C., #5Z@24"O.C. #5BA@12"O.C.
RS1 8 #4Z@24"O.C., #4Y@24"O.C. #4QQ@12"O.C.

2 # 4 "F" BARS @12" 3 # 4 "H" BARS @ 8" ON
2'-6" MIN.
ON EACH SIDE OF EACH SIDE OF EACH 2" RS2 8 #4H@12"O.C. #4Y@12"O.C. #4J@12"O.C. #4E@12"O.C. www.datumengineers.com | Co. Reg. No. F-2819
EACH EXTERIOR SUPPORT INTERIOR SUPPORT 2'-6" MIN. 2'-6" MIN. Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
#3@12" RS3 8 #4X@8"O.C. #4N@8"O.C. Datum Project No. 19166
#3@12"
DATE ISSUE TITLE
SLAB SCHEDULE NOTES 05/06/2020 ISSUE FOR SCHEMATIC DESIGN

1'-0"

4"
6"
1. GENERAL: 10/30/2020 ISSUE FOR PERMIT

BASEMENT BEAM OR WALL A. HOOKED END OF BAR TYPES "D", "G" AND "GG" SHALL BE LOCATED AT THE 01/25/2021 100% CONSTRUCTION DOCUMENTS
WALL PARALLEL TO END WHERE THE BAR IS SHOWN IN THE SCHEDULE.
OR SPANDREL 2 # 4 "H" BARS @ SLAB SPAN B. STEEL FABRICATOR SHALL DENOTE BAR TYPES ON THE SHOP DRAWINGS,
BEAM 12" AT EACH USING THE SAME BAR DESIGNATION LISTED IN THE SCHEDULE. REPRODUCE RESERVED FOR REVIEWERS NOTES
2
EXTERIOR SUPPORT
L/
THE SCHEDULE NOTES, THE BAR BENDING DIAGRAM AND THE CAST-IN-PLACE
L
L/
SCHED. BEAM CONCRETE NOTES THAT APPLY TO STEEL PLACEMENT AND DELIVER WITH
5
EACH SET OF SHOP DRAWINGS.

FACE OF
6" FROM
C. THE ENDS OF A BEAM NOTED AS LEFT AND RIGHT IN THE SCHEDULE ARE
BEAM
DETERMINED BY ORIENTING THE BEAM SO THAT THE BEAM MARK ON THE

PLAN READS FROM LEFT TO RIGHT THUS:
RIGHT LEFT
ADDITIONAL REINFORCING AT EXTERIOR BEAM OR WALL
B1
B1
PARALLEL TO DIRECTION OF SLAB SPAN OR
#4 BARS @ 12" PLACED TYPICAL DETAIL ADDITIONAL REINF. OVER TOP OF BEAMS
ON TOP OF BEAM AND
JOIST NO SCALE
G PARALLEL TO DIRECTION OF SLAB LEFT RIGHT
D. PROVIDE 180 DEGREE END HOOKS FOR LARGE BARS IN SHALLOW SLABS
PLAN REINF. IN EACH CORNER TYPICAL DETAIL WHERE A 90 DEGREE HOOK WILL NOT FIT IN THE FORMS. REV. DATE ISSUE TITLE
NOTE:
ALL COLUMNS SHOWN
NO SCALE H 2. SEE PLANS AND TYPICAL DETAILS FOR ADDITIONAL STEEL NOT SHOWN IN
IN THIS DETAIL ARE SCHEDULE. REMARKS: (APPLIES TO INDIVIDUAL SLABS JOISTS WHERE REFERENCED
TYPICAL INTERIOR IN LAST COLUMN OF THE SCHEDULE.)
OR TYPICAL EXTERIOR
COLUMNS. 3. DRAPE TOP BARS AT SLAB DROPS AND BOTTOM BARS AT CHANGES IN SLAB DEPTH.
DO NOT BEND BARS UNLESS DETAILED OR NOTED OTHERWISE.
ADDITIONAL SLAB REINFORCING
TYPICAL DETAIL F
NO SCALE
MAPLE TERRACE
3001 MAPLE AVENUE
CONCRETE SLAB SCHEDULE
AND DETAILS
CONCRETE SLAB SCHEDULE AND DETAILS 190013

PROJECT NUMBER
TOP BARS
FACE OF SUPPORTS
L2 L1 L3
22 BAR DIA.
EXTENSION @ A 22 BAR DIA.
1/2 L2 1/2 L1 EXTENSION @ A
38 BAR DIA. 38 BAR DIA. STIRRUPS
BEAMD EPTH
EXTENSION @ AA A,AA EXTENSION @ AA
22 BAR DIA. INTERMEDIATE DEVELOPER
EXTENSION @ B 1/2 L1 2" CLEAR HORIZONTAL BARS Hines
38 BAR DIA. EQUALLY SPACED. 2200 Ross Avenue, Suite 4200W
EXTENSION @ BB B,BB Dallas, TX 75201
SEE SCHEDULE.
1/3 L2 OR 1/3 L1 1/3 L3 OR 1/3 L1
WHICHEVER IS WHICHEVER IS GREATER 2800 Post Oak Blvd., 49th Floor
GREATER C Houston, TX 77056
BOTTOM BARS
D
1/3 L1 EQUITY PARTNERS
2" CLEAR McNair Interests
E
NOTES: Houston, TX 77024
1. TOTAL AREA OF INTERMEDIATE REINFORCING NEED NOT EXCEED THE AREA OF (Drew Steffen)
1/4 L1
22 BAR DIA.
1/2 L3 EXTENSION @ G TOP OR BOTTOM REINFORCING (WHICHEVER IS LARGER). Mitsui Fudosan America
F 38 BAR DIA. 2. BEAMS LESS THAN 36" DEEP DO NOT NEED INTERMEDIATE BARS UNLESS 1251 Avenue of the Americas, Suite 800
ACI STANDARD
HOOK TYPICAL
EXTENSION @ GG REQUIRED BY BEAM SCHEDULE. New York, New York 10020

3. WHERE "EXTRA INTERMEDIATE BARS" ARE SCHEDULED, PROVIDE SCHEDULED (David Leff)
G,GG 1/3 L1 OR 1/3 L3 BARS IN LIEU OF THOSE REQUIRED BY THIS DETAIL.
WHICHEVER IS GREATER
2" CLEAR 5G Studio Collaborative, LLC.
H
J Dallas, TX 75202
22 BAR DIA. 22 BAR DIA. (214-347-4982 Christine Robbins-Elrod)
EXTENSION @ K
38 BAR DIA.
1/2 L2 1/2 L3 EXTENSION @ K
38 BAR DIA. INTERMEDIATE BAR CONCRETE BEAM SCHEDULE MASTER/MULTIFAMILY ARCHITECT
EXTENSION @ KK K,KK EXTENSION @ KK GFF Architects
1/2 L3
22 BAR DIA.
EXTENSION @ L
SCHEDULE BEAM REINFORCING STIRRUPS EXTRA 2808 Fairmount St., Suite 300
Dallas, TX 75201
38 BAR DIA. INTERM. (214-303-1500 Michael Reyes)
L,LL EXTENSION @ LL BEAM NUMBER OF BEAM BARS CENTER BARS BARS
EDGE OF CANTILEVER SIZE OF BAR MARK WIDTH DEPTH BARS LEFT TOP BOTTOM CENTER TOP BARS RIGHT TOP SIZE TYPE SPACING EA. END (E.F.) REMARKS ZONING/ENTITLEMENT
1/3 L3 OR 1/3 L1 DEPTH BARS EACH FACE
OR SUPPORT WHICHEVER IS GREATER B101 36" 24" 2#7QQ, 2#7Q 2#8W, 2#8X 2#9AA, 2#9H #3 8 1@2", R@10" Baldwin Associates
36" - 48" 5 #3 3904 Elm Street, Suite B
M 2" CLEAR B102 36" 24" 2#ZZ, 2#8Y 2#7BB, 2#7E #3 8 1@2", R@10" Dallas, TX 75226
@nte, This B103 36" 24" 3#7QQ, 2#7Q 2#8W, 3#8X 3#9A, 2#9H #3 8 1@2", R@10" (214-824-7949 Robert Baldwin)
EDGE OF CANTILEVER 49" - 54" 6 #4
N OR SUPPORT should be 24" B104 36" 24" 2#8Z, 3#8Y 3#7B, 2#7E #3 8 1@2", R@10"
2" CLEAR 2" CLEAR GEOTECH
22 BAR DIA. 55" - 60" 7 #4
per Level 1 B105 18" 18" 3#7X 3#7L #3 3 1@2", R@7" EXTEND TOP BARS TO EDGE OF SLAB
ECS Southwest, LLP
1/2 L1
P EXTENSION @ Q plans? B106 18" 18" 2#7Z, 1#7Y 3#7A #3 3 1@2", R@7" 3033 Kellyway Drive, Suite 110
38 BAR DIA. 61" - 66" 8 #4 B107 18" 18" 2#7Z, 1#7Y 3#7B #3 3 1@2" R@7" Carrollton, TX 75006
EXTENSION @ QQ
Q,QQ B108 12" 18" 2#7B 2#7Z 2#7B #3 3 1@2", R@7" (972-392-3222 Siddharth Neekhra)
2" CLEAR 1/8 L1 3/4 L1 1/8 L1 67" - 72" 9 #4 B109 24"

36"/40" 18" 3#7B 2#9Z, 2#8Y 3#7Q #3 3 1@2", R@7" 1#5 EXTEND TOP BARS TO EDGE OF SLAB
CIVIL ENGINEER
B110 24" 18" 3#7X 3#8L #3 3 1@2" R@7" EXTEND TOP BARS TO EDGE OF SLAB Kimley-Horn and Associates, Inc.
V 38 BAR DIA. 73" - 78" 10 #4
B111 24" 18" 3#7Z 2#8A, 2#8H #3 3 1@2", R@7" ADDITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL H/S403-OF 13455 Noel Road, Two Galleria Office Tower, Suite 700
TO C.L. SUPPORT Dallas, TX 75240
B112 24" 18" 2#8Z, 2#8Y 2#7B, 2#7E #3 3 1@2", R@7"
W 6" (972-770-1300 Alex Rathbun)
B113 24" 18" 3#7W 3#8L #3 3 1@2", R@5" EXTEND TOP BARS INTO SLAB ON THE LEFT AND TILL EDGE OF SLAB ON RIGHT
6" X BEAM INTERMEDIATE BARS B201 24" 18" 3#7X 3#8L #3 3 1@2", R@7" EXTEND TOP BARS TO EDGE OF SLAB LANDSCAPE ARCHITECT
B202 24" 18" 3#7Y 3#9AA #3 3 1@2", R@7" ADDITITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL H/S403-OF
22 BAR DIA. @ Z
38 BAR DIA. @ ZZ Y
22 BAR DIA. @ Z
38 BAR DIA. @ ZZ TYPICAL DETAIL D B203 36" 18" 1#9QQ 2#8ZZ, 2#8Y 2#9AA, 2#9A #3 8 1@2", R@7" ADDITITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL H/S403-OF
SWA Group
TO C.L. SUPPORT TO C.L. SUPPORT Dallas, TX 75207
NO SCALE B204 36" 18" 2#8ZZ, 2#8Y 2#9AA, 2#9A #3 8 1@2", 6@4", R@7" 1#5 HOOK THE INTERM. BARS AT ENDS INTO ADJACENT SPANS. (214-954-0016 Chuck McDaniel)
Z, ZZ B205 36" 18" 2#7ZZ, 2#7Y 2#9AA, 2#9A #3 8 1@2", R@7" EXTEND TOP RIGHT BARS INTO SLAB
2" CLEAR STANDARD HOOK AT 2" CLEAR B206 18" 18" 3#7X 3#7L #3 3 1@2", R@7" EXTEND TOP BARS TO EDGE OF SLAB STRUCTURAL
DISCONTINUOUS ENDS, 2" B207 18" 18" 2#7Z, 1#7Y 3#7A #3 3 ADDITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL H/S403-OF Datum Engineers
FROM FAR SIDE OF SUPPORT 2 ADDITIONAL
STIRRUPS OF SIZE SCHEDULED B208 18" 18" 2#7Z, 1#7Y 3#7B #3 3 1@2", R@7" ADDITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL H/S403-OF Dallas, TX 75235
AND TYPE SCHEDULED REINFORCEMENT B209 30" 18" 2#7B, 1#7E 2#8Z, 2#8Y 3#7Q #3 8 1@2", R@7" EXTEND TOP BARS TO EDGE OF SLAB (214-358-0174 Rodolfo D'Arlach)
AT EACH SIDE
3" OR GREATER VARIES

B210 28" 18" 2#7B, 1#7E 2#8Z, 2#8Y 3#7Q #3 8 1@2", R@7" EXTEND TOP BARS TILL EDGE OF SLAB
75 KSI STEEL - 4000 PSI CONC. - 4 DIA. BAR SPACING MEP ENGINEER
BAR BENDING DIAGRAM B211 36" 18" 4#8W 4#9L #3 8 1@2", R@7" EXTEND TOP BARS INTO CONCRETE SLAB ON EITHER ENDS; EXTEND BOTTOM BARS TO EITHER ENDS OF CANTILEVRS.
ME Engineers, Inc.
TYPICAL DETAIL A B212 12" 18" 2#7B 2#7Z 2#7B #3 3 1@2", R@7"
SCHED. WIDTH
B213 24" 18" 3#7B 2#9Z, 2#8Y 3#7Q #3 3 1@2", R@7" 1#5 EXTEND TOP BARS TO EDGE OF SLAB Dallas, TX 75207
B301 24"/36"
38" 30" 3#8Q, 2#8QQ 3#8W, 2#8X 3#8AA, 2#8A #4 8 1@2", 18@5", R@9 1/2" 2#5 (214-741-1589 Drew Shivley)
B302 38" 30" 3#8ZZ, 2#8Y 3#8AA, 2#8A #4 8 1@2", 16@6", R@9 1/2" 2#5
#3 @ 24 TOP BAR OF SAME ELEVATOR CONSULTANT
SIZE AND SPACING B303 38" 30" 3#8W, 2#8X 3#8Q, 2#8QQ #4 8 1@2", 18@5", R@9 1/2" 2#5
AS SCHEDULED B304 24" 18" 3#8AA 3#8ZZ 3#8QQ #4 3 1@2", R@8" 1#5 8612 Broad Meadow Lane
STIRRUPS B305 24" 18" 3#7X 3#8L #3 3 1@2", R@8" McKinney, TX 75071
B306 24" 18" 2#7Z, 1#7Y 3#8A #3 3 1@2", R@8" ADDITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL H/S403-OF
B307 24" 18" 2#7Z, 1#7Y 3#8A #3 3 1@2", R@6" EXTEND TOP RIGHT BARS INTO 10" THK. SLAB. ADDITIONAL REINFORCING AT CHANGE IN BEAM WIDTH PER DETAIL INTERIOR DESIGNER
H/S403-OF
1#6 TOP & BOTTOM Rottet Studio
2" 2" B308 24" 18" 3#7X 3#8L #3 3 1@2", R@7" 808 Travis Street, Suite 100
FOR EACH 6" OF
B309 24" 18" 2#7Z, 1#7Y 3#8A #3 3 1@2", R@7" Houston, TX 77002
WIDTH INCREASE. (713-221-1830 x 6105 Anja Majkic)
TYPE 3 HOOK EA. END OF TOP 3" 3" B310 24" 18" 2#7Z, 1#7Y 3#8A #3 3 1@2", R@7" EXTEND TOP RIGHT BARS INTO 10" THICK SLAB
TYPE 1 TYPE 2
& BOTTOM REBAR. B311 30" 18" 4#9AA 2#7Z, 2#7Y 4#9QQ #3 8 1@2", R@7" EXTEND TOP BARS INTO CONCRETE SLAB ON EITHER ENDS
#3 @ 24 2'-0" TOP BAR OF SAME
SIZE AND SPACING B312 40" 18" 5#8W 5#9N #3 8 1@2", R@7" EXTEND TOP BARS INTO CONCRETE SLAB ON EITHER ENDS; EXTEND BOTTOM BARS TO EITHER ENDS OF CANTILEVERS.
AS SCHEDULED PLAN B313 12" 18" 2#7B 2#7Z 2#7B #3 3 1@2", R@7"
STIRRUPS B401 18" 18" 2#7B, 1#7E 2#7Z, 1#7Y 2#8A, 1#8H #3 3 1@2", R@7"
BEAM WITH VARYING WIDTH www.datumengineers.com | Co. Reg. No. F-2819
B402 18" 18" 2#8Z, 1#8Y #3 3 1@2", R@7" Dallas Austin San Antonio
135° HOOK AT
OPENINGS
TYPICAL DETAIL H B403 36 3/4" 18" 2#7W, 2#7X 3#8L, 1#8N #3 8 1@2", R@7" EXTEND TOP BARS TO EDGE OF SLAB
214-358-0174 512-469-9490
Datum Project No.

210-858-2880
19166
NO SCALE B404 24" 18" 3#7B 2#9Z, 2#8Y 3#7Q #3 3 1@2", R@7" 1#5 EXTEND TOP BARS TO EDGE OF SLAB DATE ISSUE TITLE
B901 38" 30" 3#8ZZ, 2#8Y 3#8AA, 2#8A #4 8 1@2", 16@6", R@9 1/2" 2#5 04/03/2020 SCHEMATIC DESIGN PRESENTATION
B902 38" 30" 3#8ZZ, 2#8Y #4 8 1@2", 16@6", R@9 1/2" 2#5 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
TYPE 4 TYPE 5 TYPE 6 BB101 12" 18" 2#7B 2#7Z 2#7B #3 3 1@2", R@7" 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
135° HOOK TOP BAR OF SAME BB102 24" 18" 3#7B 3#8Z 3#7B #3 3 1@2", R@7" HOOK 1 TOP LEFT BAR INTO BASEMENT WALL
AT OPENINGS SIZE AND SPACING 2" 10/30/2020 ISSUE FOR PERMIT
1'-6" BB201 12" 18" 2#7B 2#7Z 2#7B #3 3 1@2", R@7"
AS SCHEDULED
>3" DROP
BB202 24" 18" 3#7B 3#8Z 3#7B #3 3 1@2", R@7" HOOK 1 TOP LEFT BAR INTO BASEMENT WALL 01/25/2021 100% CONSTRUCTION DOCUMENTS
STIRRUPS BR01 24" 18" 2#7B, 1#7E 3#7Z #3 3 1@2", R@7"
STANDARD 90° HOOK
BR02 24" 18" 2#7Z, 1#7Y 3#7K #3 3 1@2", R@7"
BR03 24" 18" 2#8Z, 1#8Y 2#9A,1#9H #3 3 1@2", R@7" RESERVED FOR REVIEWERS NOTES
BR04 24" 18" 2#8Z, 1#8Y 2#9A, 1#9H #3 3 1@2", R@7" EXTEND TOP RIGHT BARS INTO 10" SLAB IN ADJACENT SPAN
BR05 24" 18" 2#7B, 1#7E 2#7Z, 1#7Y #3 3 1@2", R@7"
BR06 24" 18" 2#7Z, 1#7Y 3#7K #3 3 1@2", R@7"
TYPE 7 TYPE 8 TYPE 9
BR07 24" 18" 2#8Z, 1#8Y 2#9A, 1#9H #3 3 1@2", R@7" ADDN'L BARS PER H/S403-OF AT ELEV. OPENING
BR08 36" 18" 1#9Q 2#8Z, 1#8Y, 1#8X 2#8A, 2#7H #3 8 1@2", R@7" TOP LEFT BAR IS SCHEDULED FROM CHANGE IN WIDTH LOCATION IN BACKUP SPAN
STIRRUP TYPES BR09 24" 18" 3#9K #3 3 1@2", R@6" EXTEND TOP BARS INTO 10" SLAB IN BACKUP SPAN
BR10 24" 18" 3#7X 3#7B #3 3 1@2", R@7"
TYPICAL DETAIL BR11 30" 18" 5#9K #3 8 1@2", R@7" EXTEND TOP BARS INTO 10" SLAB IN BACKUP SPAN
NO SCALE BEAM REINFORCING,
B SEE SCHEDULE OR
SECTIONS
BR12
BR13
30"
24"
18"
18" 2#7AA, 2#7H
3#7W, 2#7X
4#7X
3#7B
4#7QQ
#3
#3
8
3
1@2", R@7"
1@2" R@7" 1#5 EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN. SEE 8/S413-OF AT ROOF DAVITS
BR14 24" 18" 2#7AA, 2#7H 4#7X 4#7QQ #3 3 1@2", R@7" 1#5 EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN. SEE 8/S413-OF AT ROOF DAVITS
NOTE: ELEVATION BR15 24" 18" 2#7AA, 2#7H 3#10X 4#7QQ #4 3 1@2", R@7" 1#5 EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN. SEE 8/S413-OF AT ROOF DAVITS
PLACE BARS IN "2ND" REV. DATE ISSUE TITLE
BR16 30" 18" 2#8AA, 2#8H 4#8X 2#8QQ, 2#8Q #3 8 1@2", R@7" 1#5 EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN. SEE 8/S413-OF AT ROOF DAVITS
LARGEST BAR DIA.
IN EITHER LAYER

LAYER DIRECTLY ABOVE OR DEEP DROP IN TOP OF BEAM BR17 24" 18" 2#7AA, 2#7H 4#7X 4#7QQ #3 3 1@2", R@7" 1#5 EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN. SEE 8/S413-OF AT ROOF DAVITS
BELOW REINFORCMENT IN
TYPICAL DETAIL
1" MIN.
BR18 24" 18" 2#7AA, 2#7H 4#7X 4#7QQ #3 3 1@2", R@7" 1#5 EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN. SEE 8/S413-OF AT ROOF DAVITS
ADJACENT LAYER. BR19 38" 30" #4 8 1@2", R@10" 2#5
NO SCALE BR20 38" 30" 2#7W, 2#7X 2#7LL, 2#7M #4 8 1@2", R@10" 2#5
TOP BARS BR21 38" 30" 2#7ZZ, 2#7Y 2#7ZZ, 2#7H #4 8 1@2", R@10" 2#5
< 3" DROP
BR22 38" 30" 2#7ZZ, 2#7Y #4 8 1@2", R@10" 2#5

5"
MAXIMUM 1:6 SLOPE IN BR23 24" 18" 2#7AA, 1#7H 3#10Z 3#7B #4 3 1@2", R@7" EXTEND TOP LEFT BARS INTO 10" SLAB IN BACKUP SPAN
BENT TOP BARS BR24 24" 18" 3#7B 3#9Z 3#7B #4 3 1@2", R@7"
TOP BARS BAR SUPPORT AS

SPECIFIED "2ND" REQUIRED BEAM SCHEDULE NOTES
IN BEAM SCHEDULE "EXTRA 1. GENERAL:
INTERMEDIATE
BARS" EQUALLY A. HOOKED END OF BAR TYPES "D", "G" AND "GG" SHALL BE LOCATED AT THE END WHERE E. PROVIDE 180 DEGREE END HOOKS FOR LARGE BARS IN SHALLOW BEAMS WHERE A 90 REMARKS: (APPLIES TO INDIVIDUAL BEAMS WHERE REFERENCED IN LAST COLUMN OF THE
SPACED AT EACH THE BAR IS SHOWN IN THE SCHEDULE. DEGREE HOOK WILL NOT FIT IN THE FORMS. SCHEDULE.)
SIDE OF BEAM SEE B. STEEL FABRICATOR SHALL DENOTE BAR TYPES ON THE SHOP DRAWINGS, USING THE
BOTTOM BARS DETAIL D/CTB-1 SAME BAR DESIGNATION LISTED IN THE SCHEDULE. REPRODUCE THE SCHEDULE NOTES, 2. SEE PLANS AND TYPICAL DETAILS FOR ADDITIONAL STEEL NOT SHOWN IN SCHEDULE. 6. WHERE BEAM WIDTH VARIES IN PLAN, SEE H/S403-OF FOR REINFORCING LAYOUT AND
SPECIFIED "2ND" IN THE BAR BENDING DIAGRAM AND THE CAST-IN-PLACE CONCRETE NOTES THAT APPLY TO ADDITIONAL REINFORCING IN EXTRA WIDTH, U.N.O.
BAR SPACERS
BEAM SCHEDULE STEEL PLACEMENT AND DELIVER WITH EACH SET OF SHOP DRAWINGS. 3. STIRRUP TYPES ARE SYMBOLICALLY SHOWN AND CLOSELY REPRESENT THE ACTUAL STIRRUP
AS REQUIRED
C. PROVIDE STIRRUP SUPPORT BAR AT TOP OF EACH STIRRUP LEG WHICH CANNOT BE TYPE REQUIRED. THE CONTRACTOR SHALL REVIEW THE DRAWINGS AND FABRICATE THE 7. PLACE BOTTOM REINFORCEMENT IN TWO LAYERS.
SUPPORTED WITH A SCHEDULED TOP BAR. SIZE OF STIRRUP SUPPORT BAR SHALL STIRRUPS TO THE ACTUAL BEAM PROFILE SHOWN ON THE DRAWINGS, INCLUDING NOTCHES AND
BEAM REINFORCING MATCH SIZE OF STIRRUP. LAP STIRRUP SUPPORT BARS 1'-0" WITH SCHEDULED TOP OFFSETS TO BE CAST INTO THE BEAM. 8. PLACE TOP REINFORCEMENT IN TWO LAYERS.
LARGEST BAR DIA.
SEE SCHEDULE 2#5 ADDITIONAL BARS OR MAKE CONTINUOUS IF REQUIRED.

IN EITHER LAYER,
2"
OR SECTIONS BARS FOR EACH BENT D. THE ENDS OF A BEAM NOTED AS LEFT AND RIGHT IN THE SCHEDULE ARE DETERMINED 4. INTERMEDIATE LONGITUDINAL BARS IN BEAMS SHALL BE CONTINUOUS BETWEEN SUPPORTS AND 9. DRAPE TOP BARS AT SLAB DROPS AND BOTTOM BARS AT CHANGES IN BEAM DEPTH.
1" MINIMUM
BOTTOM BARS TOP BAR LOCATED AT DO NOT BEND BARS UNLESS DETAILED OR NOTED OTHERWISE.
BY ORIENTING THE BEAM SO THAT THE BEAM MARK ON THE PLAN READS FROM LEFT TO SHALL EXTEND AT LEAST 65 BAR DIAMETERS BEYOND THE NEAR FACE OF SUPPORT AT EACH END.
BOTTOM OF SLOPE IN RIGHT THUS:. AT DISCONTINUOUS ENDS, WHERE THE SUPPORT WIDTH DOES NOT PERMIT THE REQUIRED BAR MAPLE TERRACE
ELEVATION TOP BAR RIGHT LEFT EXTENSION, PROVIDE A STANDARD 90 DEGREE HOOK 3" FROM THE FAR FACE. WHERE BEAM 3001 MAPLE AVENUE
DEPTHS ARE 36" OR MORE, PROVIDE INTERMEDIATE BARS AS SHOWN IN DETAIL D/S403-OF, DALLAS, TEXAS, 75201
UNLESS MORE BARS ARE REQUIRED BY "EXTRA INTERMEDIATE BARS" IN THE BEAM SCHEDULE.
CONCRETE BEAM SCHEDULE
B1
B1
BEAM REINFORCING PLACEMENT SHALLOW DROP IN TOP OF BEAM OR
TYPICAL DETAIL TYPICAL DETAIL 5. WHERE #14 AND #18 BARS ARE SCHEDULED TO LAP PER THE BAR BENDING DIAGRAM, PROVIDE AND DETAILS
C E LEFT RIGHT MECHANICAL SPLICES PER SPECIFICATIONS IN LIEU OF LAPS. STAGGER SPLICES IN ADJACENT
BARS BY 2'-0" MIN.
NO SCALE NO SCALE
190013
PROJECT NUMBER
TYPICAL CONCRETE BEAM SCHEDULE DETAILS

DETAIL FOR DETAIL FOR
POST- TENSIONED CONCRETE BEAM SCHEDULE
DISCONTINUOUS ENDS CONTINUOUS ENDS
DRAP REINFORCING STIRRUPS EXTRA
P-T DRAPE E B DRAPE BARS BARS INTERM.
C.L. SUPPORT C.L. SUPPORT BEAM WIDT DEPT FORCE DRAPE A LEFT CENT C RIGHT DRAP BARS LEFT CENTER CENTER BARS RIGHT BARS
MARK H H (KIPS) TYPE END ER END ED TOP BOTTOM TOP TOP SIZE TYPE SPACING EA. END (E.F.) REMARKS
PTB201 24" 18" 360k C/S404-OF 12 1 3/4 12 2#8B, 2#8E 2#8Z, 2#8Y 2#8B, 2#8E 3 3 1@2", 8@6", R@12" O.C.
BEARING REVERSE PTB202 24" 18" 325k C/S404-OF 12 1 3/4 12 2#8B, 2#8E 2#8Z, 2#8Y 2#8A, 2#8H 3 3 1@2", 8@6", R@12" O.C.
1/12
PLATE PARABOLIC DRAPE
PTB203 24" 18" 325k C/S404-OF 12 10 12 2#8Z, 2#8Y 4#8Q 3 3 1@2", R@12" O.C. EXTEND TOP RIGHT BARS TO SLAB EDGE DEVELOPER
SPAN
PTB204 33" 18" 140k C/S404-OF 9 9 16 2#7BB 2#7ZZ 2#7AA 3 3 1@2", R@12" O.C. Hines
TENDONS PARABOLIC DRAPE 2200 Ross Avenue, Suite 4200W
PTB205 33" 18" 240k D/S404-OF 16 1 16 10'-7" 2#7E 2#7Z, 2#7Y 3 8 1@2" R@12" O.C. TOP LEFT 'E' BARS SHALL START FROM PTB204 WHERE BEAM WIDTH CHANGES FROM 18" TO 33" Dallas, TX 75201
PTB206 36 3/4" 18" 240k C/S404-OF 16 13 10.5 2#7W, 2#7X 2#7L, 2#7M 3 8 1@2", R@12" O.C. (972-716-2908 Corbin Eckel)
PTB207 36 3/4" 18" 240k F/S404-OF 10.5 9 3 8 1@2", R@6" O.C.
PTB208 36" 18" 160k C/S404-OF 9 1.75 9 2#7QQ, 2#7Q 2#7ZZ, 2#7Z 2#7QQ, 2#7Q 3 8 1@2", R@6" O.C.
"B"
Houston, TX 77056
"C"
"A"
PTB801 36" 42" 725k F/S404-OF 21 38 4 8 1@2", 8@10", R@12" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS (713-621-8000 Juan Delgado)
PTB802 36" 42" 725k C/S404-OF 38 38 38 3#8W, 3#7X 3#8LL, 3#7L 4 8 1@2", R@10" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS
EQUITY PARTNERS
OF TENDON AT END
OF TENDON AT END
REVERSE PARABOLIC DRAPE PTB803 36" 42" 725k C/404-OF 38 27 21 3#8Z, 3#7Y 2#8B, 4#7A 4 8 1@2", R@12" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS ,
DISTANCE TO C.G.
DISTANCE TO C.G.
DISTANCE TO C.G.
ADDITIONAL REINFORCING AT CHANGE IN WIDTH PER DETAILH/S403-OF McNair Interests
TO 1/12 POINT IS PERMISSIBLE POINT OF INFLECTION
OF TENDON AT
FOR UNBONDED MONOSTRAND PTB804 36" 42" 1100k F/S404-OF 21 38 4 8 1@2", 24@5", R@9 1/2" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS Houston, TX 77024
LOW POINT
TENDONS AT DISCONTINUOUS PTB805 36" 42" 1100k C/S404-OF 38 38 38 3#8W, 3#7X 3#8LL, 3#7L 4 8 1@2", R@10" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS (Drew Steffen)
ENDS (TO MAKE BEARING PLATE
NOTE: PTB806 36" 42" 1100k C/S404-OF 38 29.5 21 3#8Z, 3#7Y 2#8B, 4#7A 4 8 1@2", R@12" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS
VERTICAL). Mitsui Fudosan America
DIMENSION "D" SHALL BE TO PTB807 38" 30" 675k F/S404-OF 15 26 4 8 1@2", 18@5", R@9 1/2" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS 1251 Avenue of the Americas, Suite 800
MIDSPAN OF BEAM UNLESS NOTED PTB808 38" 30" 675k C/S404-OF 26 18 15 3#8QQ, 3#7Q 3#8W, 3#7X 3#8AA, 2#8A 4 8 1@2", 18@5", R@9 1/2" O.C. 2#5 AFTER LEVEL 8 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS New York, New York 10020
OTHERWISE IN SCHEDULE. (David Leff)
"D" PTB809 36" 42" 725k C/S404-OF 21 27 38 3#8AA, 3#7AA 3#8W, 3#7X 4 8 1@2", R@12" O.C. 2#5 EXTEND THE TOP BARS AT LEFT END INTO THE SLAB. MAINTAIN CONSTANT DRAPE OF 21" IN THE BEAM
EXTENSION ON LEFT SIDE
PARABOLIC TENDON PROFILE PTB810 36" 42" 1100k C/S404-OF 21 29.5 38 3#8AA, 3#7AA 3#8W, 3#7X 4 8 1@2", R@12" O.C. 2#5 EXTEND THE TOP BARS AT LEFT END INTO THE SLAB. MAINTAIN CONSTANT DRAPE OF 21" IN THE BEAM 5G Studio Collaborative, LLC.
EXTENSION ON LEFT SIDE 1217 Main St., Suite 500
TYPICAL DETAIL C PTB901 36" 42" 550k F/S404-OF 21 38 4 8 1@2", 8@10", R@12" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS. Dallas, TX 75202
NO SCALE PTB902 36" 42" 550k C/S404-OF 38 38 38 3#8W, 3#7X 3#8LL, 3#7L 4 8 1@2", R@10" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS.
PTB903 36" 42" 550k C/S404-OF 38 27 21 3#8Z, 3#7Y 2#8B, 4#7A 4 8 1@2", R@12" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS , MASTER/MULTIFAMILY ARCHITECT
DETAIL FOR DETAIL FOR
ADDITIONAL REINFORCING AT CHANGE IN WIDTH PER DETAILH/S403-OF
GFF Architects
DISCONTINUOUS ENDS CONTINUOUS ENDS PTB904 36" 42" 850k F/S404-OF 21 38 4 8 1@2", 24@5", R@9 1/2" O.C 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS. 2808 Fairmount St., Suite 300
PTB905 36" 42" 850k C/S404-OF 38 38 38 3#8W, 3#7X 3#8LL, 3#7L 4 8 1@2", R@10" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS. Dallas, TX 75201
C.L. SUPPORT C.L. SUPPORT PTB906 36" 42" 850k C/S404-OF 38 29.5 21 3#8Z, 3#7Y 2#8B, 4#7A 4 8 1@2", R@12" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS.
PTB907 38" 30" 500k F/S404-OF 15 26 4 8 1@2", 18@5", R@9 1/2" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS. ZONING/ENTITLEMENT
STRAIGHT LINE 1/12 1/12 STRAIGHT LINE 1/12 PTB908 38" 30" 500k C/S404-OF 26 18 15 3#8QQ, 3#7Q 3#8W, 3#7X 3#8AA, 2#8A 4 8 1@2", 18@5", R@9 1/2" O.C. 2#5 AFTER LEVEL 9 POUR, STRESS 60% OF TENDONS. AFTER ROOF POUR, STRESS 100% OF TENDONS. Baldwin Associates
PTB909 36" 42" 550k C/S404-OF 21 27 38 3#8AA, 3#7AA 3#8W, 3#7X 4 8 1@2", R@12" O.C. 2#5 EXTEND THE TOP BARS AT LEFT END INTO THE SLAB. MAINTAIN CONSTANT DRAPE OF 21" IN THE BEAM 3904 Elm Street, Suite B
SPAN SPAN SPAN Dallas, TX 75226
BEARING EXTENSION ON LEFT SIDE
PLATE PTB910 36" 42" 850k C/S404-OF 21 29.5 38 3#8AA, 3#7AA 3#8W, 3#7X 4 8 1@2", R@12" O.C. 2#5 EXTEND THE TOP BARS AT LEFT END INTO THE SLAB. MAINTAIN CONSTANT DRAPE OF 21" IN THE BEAM
REVERSE EXTENSION ON LEFT SIDE
TENDONS PARABOLIC CONCRETE BEAM SCHEDULE NOTES GEOTECH
DRAPE ECS Southwest, LLP
1. GENERAL: 3033 Kellyway Drive, Suite 110
2. SEE PLANS AND TYPICAL DETAILS FOR ADDITIONAL STEEL NOT SHOWN IN (972-392-3222 Siddharth Neekhra)
A. HOOKED END OF BAR TYPES "D", "G" AND "GG" SHALL BE LOCATED AT THE END WHERE 7. WHERE A CHANGE IN SCHEDULED "P-T FORCE" OCCURS IN ADJACENT BEAMS
"C"
"A"
THE BAR IS SHOWN IN THE SCHEDULE. SCHEDULE. RESULTING IN DIFFERENT TENDON QUANTITY REQUIREMENTS, THE EXCESS TENDONS
SHALL BE TERMINATED IN THE SPAN REQUIRING FEWER TENDONS AT THE SPAN CIVIL ENGINEER
B. STEEL FABRICATOR SHALL DENOTE BAR TYPES ON THE SHOP DRAWINGS, USING THE 3. STIRRUP TYPES ARE SYMBOLICALLY SHOWN AND CLOSELY REPRESENT THE QUARTER POINT NEAREST THE SPAN REQUIRING MORE TENDONS, UNLESS NOTED Kimley-Horn and Associates, Inc.
"B"
OF TENDON AT END
OF TENDON AT END
SAME BAR DESIGNATION LISTED IN THE SCHEDULE. REPRODUCE THE SCHEDULE ACTUAL STIRRUP TYPE REQUIRED. THE CONTRACTOR SHALL REVIEW THE OTHERWISE. REMARKS: (APPLIES TO INDIVIDUAL BEAMS WHERE REFERENCED IN LAST 13455 Noel Road, Two Galleria Office Tower, Suite 700
REVERSE PARABOLIC DRAPE
DISTANCE TO C.G.
DISTANCE TO C.G.
DISTANCE TO C.G.
Dallas, TX 75240
TO 1/12 POINT IS PERMISSIBLE NOTES, THE BAR BENDING DIAGRAM AND THE CAST-IN-PLACE CONCRETE NOTES THAT DRAWINGS AND FABRICATE THE STIRRUPS TO THE ACTUAL BEAM PROFILE SHOWN COLUMN OF THE SCHEDULE.) (972-770-1300 Alex Rathbun)
OF TENDON AT
FOR UNBONDED MONOSTRAND APPLY TO STEEL PLACEMENT AND DELIVER WITH EACH SET OF SHOP DRAWINGS. ON THE DRAWINGS, INCLUDING NOTCHES AND OFFSETS TO BE CAST INTO THE
BEAM. REMARKS: (APPLIES TO INDIVIDUAL BEAMS WHERE REFERENCED IN LAST COLUMN
LOW POINT
TENDONS AT DISCONTINUOUS PARABOLIC CURVE LANDSCAPE ARCHITECT

ENDS (TO MAKE BEARING C. PROVIDE STIRRUP SUPPORT BAR AT TOP OF EACH STIRRUP LEG WHICH CANNOT BE OF THE SCHEDULE
4. INTERMEDIATE LONGITUDINAL BARS IN BEAMS SHALL BE CONTINUOUS BETWEEN SWA Group
PLATE VERTICAL). SUPPORTED WITH A SCHEDULED TOP BAR. SIZE OF STIRRUP SUPPORT BAR SHALL
MATCH SIZE OF STIRRUP. LAP STIRRUP SUPPORT BARS 1'-0" WITH SCHEDULED TOP SUPPORTS AND SHALL EXTEND AT LEAST 65 BAR DIAMETERS BEYOND THE FACE OF 8. PLACE BOTTOM REINFORCEMENT IN TWO LAYERS. Dallas, TX 75207
NOTE: BARS OR MAKE CONTINUOUS IF REQUIRED. SUPPORT AT EACH END. AT DISCONTINUOUS ENDS, WHERE THE SUPPORT WIDTH (214-954-0016 Chuck McDaniel)
DIMENSION "D" SHALL BE TO DOES NOT PERMIT THE REQUIRED BAR EXTENSION, PROVIDE A STANDARD 90 9. PLACE TOP REINFORCEMENT IN TWO LAYERS.
"D" D. THE ENDS OF A BEAM NOTED AS LEFT AND RIGHT IN THE SCHEDULE ARE DETERMINED DEGREE HOOK 3" FROM THE FAR FACE.
MIDSPAN OF BEAM UNLESS STRUCTURAL
NOTED OTHERWISE IN SCHEDULE. BY ORIENTING THE BEAM SO THAT THE BEAM MARK ON THE PLAN READS FROM LEFT 10. DRAPE TOP BARS AT SLAB DROPS AND BOTTOM BARS AT CHANGES IN BEAM DEPTH. DO Datum Engineers
TO RIGHT THUS: 5. DRAPE PROFILE SHALL CONFORM TO DETAIL C, D, F, OR G/S404-OF AS INDICATED IN NOT BEND BARS UNLESS DETAILED OR NOTED OTHERWISE. 6516 Forest Park Road
THE DRAPE TYPE COLUMN. Dallas, TX 75235
RIGHT LEFT (214-358-0174 Rodolfo D'Arlach)
6. SCHEDULED "P-T FORCE" IS FINAL EFFECTIVE POST-TENSIONING FORCE AFTER ALL
B1
OR LOSSES HAVE OCCURRED. WHERE NO FORCE IS GIVEN, BEAM IS CONVENTIONALLY MEP ENGINEER
B1
HARPED TENDON PROFILE REINFORCED ONLY. ME Engineers, Inc.
LEFT RIGHT 1825 Market Center Blvd., Suite 600
TYPICAL DETAIL E. PROVIDE 180 DEGREE END HOOKS FOR LARGE BARS IN SHALLOW BEAMS WHERE A 90
Dallas, TX 75207
NO SCALE
D DEGREE HOOK WILL NOT FIT IN THE FORMS.
ELEVATOR CONSULTANT
TOP BAR OF SAME Persohn | Hahn Associates, Inc.
#3 @ 24 8612 Broad Meadow Lane
SIZE AND SPACING McKinney, TX 75071
AS SCHEDULED (972-832-4232 Tom Williams)
STIRRUPS
INTERIOR DESIGNER
PARABOLIC DRAPE- IF Rottet Studio
"B" & "D" DIM. ARE IN 1/12 808 Travis Street, Suite 100
OUTSIDE EDGE SCHEDULE, STRAIGHT 1/4 SPAN LENGTH Houston, TX 77002
LINE IF NOT. POINT FACE OF SUPPORTS (713-221-1830 x 6105 Anja Majkic)
OF CANTILEVER L2 L1 L3
C.L. SUPPORT 1 1/2" TYP. 4" 1 1/2 TYP. 22 BAR DIA.
1/2 SCHEDULED
TYPE 1 TYPE 2 TYPE 3 EXTENSION @ A 22 BAR DIA.

TENDON 1/2 L2 1/2 L1 EXTENSION @ A
2'-0"
DEPTH
#3 @ 24 TOP BAR OF SAME 38 BAR DIA. 38 BAR DIA.

1B/PTG-4 SIZE AND SPACING EXTENSION @ AA A,AA EXTENSION @ AA
AS SCHEDULED 22 BAR DIA. www.datumengineers.com | Co. Reg. No. F-2819
STIRRUPS EXTENSION @ B 1/2 L1 2" CLEAR Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
38 BAR DIA.
"C"
SCHEDULED TOP "A" BARS

EXTENSION @ BB B,BB Datum Project No. 19166
"A"
135° HOOK AT DATE ISSUE TITLE

1/3 L2 OR 1/3 L1 1/3 L3 OR 1/3 L1
"B"
OPENINGS
SCHEDULED DEPTH
SCHEDULED TOP "H" BARS 04/03/2020 SCHEMATIC DESIGN PRESENTATION

OF TENDON AT END
OF TENDON AT END
WHICHEVER IS WHICHEVER IS GREATER

DISTANCE TO C.G.
DISTANCE TO C.G.
PROVIDE STANDARD GREATER C 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
"D" HOOK EACH SIDE OF 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
POUR STRIP TYPE 4 TYPE 5 TYPE 6

D
REVERSE 1/3 L1 10/30/2020 ISSUE FOR PERMIT
PARABOLIC CURVE 135° HOOK TOP BAR OF SAME 2" CLEAR 12/18/2020 90% CONSTRUCTION DOCUMENTS
CENTER OF GRAVITY OF AT OPENINGS SIZE AND SPACING 01/25/2021 100% CONSTRUCTION DOCUMENTS
TENDONS AS SCHEDULED E
STIRRUPS
1/4 L1
SPREAD POST-TENSIONING 22 BAR DIA.
2'-0" 1/2 L3 EXTENSION @ G
TENDONS FOR INTERMEDIATE
4#5 x AT BEAMS AND STRESSING ANCHORS, F 38 BAR DIA.
ACI STANDARD
HOOK TYPICAL
6#5 AT GIRDERS EACH SIDE WHERE REQUIRED EXTENSION @ GG
OF JOINT EQUALLY SPACED
G,GG 1/3 L1 OR 1/3 L3
ACROSS BEAM WIDTH WHICHEVER IS GREATER
SCHEDULED BOTTOM
BARS CONTINUOUS TYPE 7 TYPE 8 TYPE 9 2" CLEAR
THRU JOINT H
J
CANTILEVER TENDON PROFILE BEAM CONSTRUCTION JOINT - ELEVATION STIRRUP TYPES 22 BAR DIA. 22 BAR DIA.
EXTENSION @ K
TYPICAL DETAIL F TYPICAL DETAIL G TYPICAL DETAIL 38 BAR DIA.
1/2 L2 1/2 L3 EXTENSION @ K
38 BAR DIA.
NO SCALE NO SCALE M EXTENSION @ KK K,KK EXTENSION @ KK
22 BAR DIA.
1/2 L3 EXTENSION @ L
NOTE: 38 BAR DIA. REV. DATE ISSUE TITLE
PLACE BARS IN "2ND" LAYER L,LL EXTENSION @ LL
CONSTRUCTION JOINT-SEE CPT-2G .05 12/18/2020 Permit Set Update
DIRECTLY ABOVE OR BELOW EDGE OF CANTILEVER 1/3 L3 OR 1/3 L1
INTERMEDIATE STRESSING REINFORCMENT IN ADJACENT OR SUPPORT WHICHEVER IS GREATER
BURSTING STEEL ANCHORS WITH POCKET LAYER.
M 2" CLEAR
FORMERS TOP BARS
1 1/2" EDGE OF CANTILEVER
N OR SUPPORT
POST-TENSIONING TENDONS, WITH 2" CLEAR 2" CLEAR
CLEAR SCHED. C.G. AND DRAPE 22 BAR DIA.
P EXTENSION @ Q
1/2 L1
BURN OFF EXCESS DEAD END IF 38 BAR DIA.
STRAND 1/2" BEHIND STRESSED EXTENSION @ QQ
#11 BAR SPACERS Q,QQ
FACE OF CONCRETE FROM ONE TOP BARS @ 4'-0" O.C. 2" CLEAR 1/8 L1 3/4 L1 1/8 L1
AFTER STRESSING. END ONLY SPECIFIED "2ND"
STRAND HARDWARE IN BEAM
"EXTRA INTERMEDIATE V 38 BAR DIA.
SHALL BE COATED WITH SCHEDULE
RUST-PREVENTIVE BARS" EQUALLY SPACED TO C.L. SUPPORT
MASTIC BEFORE AT EACH SIDE OF BEAM W 6"
POCKETS ARE
GROUTED. PACK BOTTOM BARS 6" X
POCKET WITH NON- SPECIFIED "2ND" IN 22 BAR DIA. @ Z 22 BAR DIA. @ Z
SHRINK GROUT. #11 BAR Y
BEAM SCHEDULE 38 BAR DIA. @ ZZ 38 BAR DIA. @ ZZ
SPACERS @ TO C.L. SUPPORT TO C.L. SUPPORT
4'-0" O.C.
Z, ZZ
NOTE: 2" CLR.
2" CLEAR STANDARD HOOK AT 2" CLEAR
CONTRACTOR SHALL DESIGN DISCONTINUOUS ENDS, 2"
AND PROVIDE MILD REINFORCING BURSTING STEEL FROM FAR SIDE OF SUPPORT
TO RESIST BURSTING, SPLITTING BOTTOM BARS
AND SPALLING FORCES IN
ANCHORAGE ZONES.
MAPLE TERRACE
75 KSI STEEL - 4000 PSI CONC. - 4 DIA. BAR SPACING
3001 MAPLE AVENUE
BAR BENDING DIAGRAM
POST-TENSIONED BEAM
BEAM REINFORCING PLACEMENT
TYPICAL DETAIL P-T CONCRETE BEAM
TYPICAL DETAIL TYPICAL DETAIL Q H
P NO SCALE
SCHEDULE AND DETAILS
POST-TENSIONED BEAM SCHEDULE AND DETAILS 190013

PROJECT NUMBER
TWO-WAY FLAT PLATE SLAB SCHEDULE - COLUMN STRIP
C.L. COLUMN
C.L. EXTERIOR COLUMN, SLAB REINFORCEMENT
BEAM, OR WALL SLAB
L2 THICK. TOP BARS BOTTOM BARS TOP BARS TOP BARS REMARKS
L1 MARK
OUTSIDE
(IN.) LEFT END CENTER CENTER RIGHT END
L1c (CLEAR) L2c (CLEAR) L3c (CLEAR)
EDGE 2#7XIX,
9C1 10 8#5III NOTE 2,13 DEVELOPER
OF 6#5XIX
FLAT SLABS NOTES FACE OF
CONC. FACE OF SUPPORT FACE OF SUPPORT 9C2 10 8#5III 5#5I. 4#5II NOTE 2,13 Hines
1'-0" 1'-0" SUPPORT 2200 Ross Avenue, Suite 4200W
#5X @12" O.C. N/S DIRECTION A. SPACE ALL BARS EQUALLY ACROSS MIDDLE STRIPS AND ACROSS THE BOTTOM OF ALL 0.33 L2c OR 0.33 L3c 9C3 10 8#5III NOTE 2,13 Dallas, TX 75201
EA. WAY AT BOT. OF COLUMN STRIPS, EXCEPT AS SHOWN IN SLAB OPENING DETAILS. WHICHEVER IS I 9C4 10 8#5III 2#7XIX, 6#5XIX NOTE 2,13 (972-716-2908 Corbin Eckel)
DROP PANEL GREATER 9C5 10 6#5XIII 3#8III, 3#5III NOTE 2
B. WHERE MORE THAN ONE BAR TYPE IS SCHEDULED FOR A COLUMN OR MIDDLE STRIP, 2800 Post Oak Blvd., 49th Floor
0.22 L2c OR 0.22 L3c 1#8XVI, Houston, TX 77056
ALTERNATE THE BAR TYPES ACROSS THE WIDTH OF THE STRIP, EXCEPT AS NOTED IN WHICHEVER IS II 9C6 10 6#5III NOTE 2
NOTE 3. WHERE TWO BAR TYPES ARE SCHEDULED AT A SPACING, ALTERNATE BAR 5#6XVI (713-621-8000 Juan Delgado)
GREATER
10"
TYPES AT THEIR SCHEDULED SPACING, TO OBTAIN A MAT OF BARS AT 1/2 THE 9C7 10 3#7III, 3#5III 3#7I, 3#7II NOTE 2
SCHEDULED SPACING. III 9C8 10 6#5III 6#8XVI NOTE 2 EQUITY PARTNERS
McNair Interests
9"
CLASS B SPLICE/2 9C9 10 3#8III, 3#5III 6#5XIII NOTE 2
C. IN COLUMN STRIPS WITHOUT BEAMS, PLACE A MINIMUM OF 25 PERCENT OF THE 109 N. Post Oak Lane, Suite 600
9C10 10 9#6III 5#8XXI NOTE 2 Houston, TX 77024
COLUMN STRIP TOP BARS WITHIN A SPACE EQUAL TO THE COLUMN DIMENSION, IV 9C11 10 8#7XIII 2#7VIII, 6#7III 9#8XVI NOTE 9 (Drew Steffen)
PERPENDICULAR TO THE BARS, PLUS 1'-0". SPACE THE REMAINING BARS EQUALLY OVER
THE REST OF THE COLUMN STRIP. EXTEND 2 SCHEDULED COLUMN STRIP BOTTOM BARS 6" MIN. 6" MIN. 8#8XIII,
9C12 10 8#7XIII 2#7VIII, 7#7III NOTE 4,9 Mitsui Fudosan America
THROUGH INTERIOR COLUMN CAGE EACH WAY AND SPLICE WITH A CLASS A SPLICE, 4#8XVII 1251 Avenue of the Americas, Suite 800
COLUMN V
PLACE TYPE VIII BAR HOOKS WITHIN EXTERIOR COLUMNS. 9C13 10 12#5XIII 2#7VIII, 14#7III NOTE 1 New York, New York 10020
SEE PLAN 3" MAX. 3" MAX. (David Leff)
6#10XIX,
D. STEEL PLACING SEQUENCE SHALL BE AS FOLLOWS: 9C14 10 14#5VIII NOTE 9,11
VI 6#9XIX
EAST-WEST OFFICE/RETAIL ARCHITECT
6'-0" 6'-0" NORTH- BARS 9C15 8 12#5III NOTE 1
1" CLR.
0.125 L2 MAX. 0.125 L2 MAX. 5G Studio Collaborative, LLC.
U.N.O. ON PLAN U.N.O. ON PLAN SOUTH BARS 9C16A 10 6#8XIII 6#6VIII 6#9XVII NOTE 15 1217 Main St., Suite 500
2" TYP. VII 9C16B 10 6#6III 6#8XVII NOTE 15 Dallas, TX 75202
PLACE CONDUIT ON 0.15 L2 MAX. 0.15 L2 MAX. 3#9XVII,
9C17A 10 6#5III NOTE 2,5,8
TOP OF BOTTOM 3#5XVII MASTER/MULTIFAMILY ARCHITECT
DROP PANEL MAT. SEE ELECTRICAL VIII 9C17B 10 6#5III 3#8XVII NOTE 2 TWO-WAY FLAT PLATE SLAB SCHEDULE - MIDDLE STRIP GFF Architects
CLASS B SPLICE/2 9C18A 10 3#5XIV 6#5III NOTE 2,4,5 2808 Fairmount St., Suite 300
TYPICAL DETAIL NO SCALE, TYP. U.N.O. A IX 9C18B 10 6#5III NOTE 2 SLAB
SLAB
THICK.
REINFORCEMENT
TOP BARS BOTTOM BARS TOP BARS TOP BARS REMARKS
Dallas, TX 75201
MARK
1" CLR.
6"MIN. RC1 10 8#5XIX 5#5VIII NOTE 1,2,13
(IN.) LEFT END CENTER CENTER RIGHT END
RC2 10 5#5III 3#5I, 2#5II NOTE 2,13 ZONING/ENTITLEMENT
X FACE OF SUPPORT RC3 10 5#5III NOTE 2,13 9M1 10 8#5XIX 4#5IX, 4#5XII NOTE 13 Baldwin Associates
0.33 L1c OR 0.33 L2c RC4 10 5#5VIII 8#5XIII NOTE 1,2,13 9M2 10 8#5III 5#5I, 4#5II NOTE 13 3904 Elm Street, Suite B
WHICHEVER IS 9M3 10 8#5III NOTE 13 Dallas, TX 75226
RC5 10 6#5XIII 2#5VIII, 4#5XI NOTE 2 (214-824-7949 Robert Baldwin)
E. THE FOLLOWING NOTES APPLY ONLY WHERE REFERENCED FROM THE SCHEDULE. XI GREATER 2#7XIX,
RC6 10 6#5III 6#5XVI NOTE 2,3 9M4 10 8#5III NOTE 13
CLASS B SPLICE/2 6#5XIX GEOTECH
1. EXTEND THE TOP/BOTTOM BARS TO CANTILEVER END/SLAB EDGE/OPENING. HOOK RC7 10 6#5III 4#5I, 4#5II NOTE 2,3
9M5 10 11#5III 11#5II ECS Southwest, LLP
TOP BARS AT DISCONTINUOUS ENDS. XII RC8 10 6#5III 4#6I, 4#6II NOTE 4,5
9M6 10 11#5III 11#5III 3033 Kellyway Drive, Suite 110
MIDDLE COLUMN STRIP 2. SEE DETAIL H/S405-OF FOR PLACEMENT OF BARS. LARGER BARS SCHEDULED SHALL 0.15 L1 MAX. RC9 10 6#6XIII 12#5III NOTE 4 Carrollton, TX 75006
BE PLACED ADJACENT TO BEAM FIRST. 9M7 10 11#5III 11#5II
STRIP 4#8XVI, (972-392-3222 Siddharth Neekhra)
3. SCHEDULE CONSIDERING SW-1 FRAMING ORTHOGONAL TO SPAN AS A SUPPORT. RC10 10 8#5III NOTE 5,11 9M8 10 11#5III 11#5XVI
XIII 7#7XVI
COL. 4. HOOK 'XIII' BARS AT THE OPENING. IF SCHEDULED, PLACE 'I' OR 'XIX' OR 'XVI' BARS 0.33 L1c 9M9 10 12#5III 11#5XIII CIVIL ENGINEER
STRIP RC11 10 3#5XIV 4#6III, 8#5III NOTE 9,11
(EXTENDING INTO NEXT SPAN) ADJACENT TO OPENING WITHIN COLUMN/MIDDLE 9M10 10 7#5XIII 7#5IX, 7#5XII 11#5XIII NOTE 1,9 Kimley-Horn and Associates, Inc.
RC12A 8 8#5III 6#8XVI NOTE 2
HOOK TYPICAL
REINF. STRIP. 13455 Noel Road, Two Galleria Office Tower, Suite 700
XIV RM1 10 6#5XIX 3#5IV, 3#5VII NOTE 1,13
5. TERMINATE 'III' BOTTOM BARS WITH A HOOK AT THE OPENING. EDGE OF OPENING RC12B 10 6#5III 5#7XVI NOTE 2 Dallas, TX 75240
THICKNESS
GREATER
6. HOOK VII BARS AT THE OPENING. PLACE SCHEDULED IV BARS ADJACENT TO RC13A 8 5#5VIII, 5#5III 5#5XIII NOTE 2 RM2 10 3#5IV, 3#5VII 6#5II NOTE 13 (972-770-1300 Alex Rathbun)
SCHED.
OPENINGS. 2" 2" RM3 10 3#5IV, 3#5VII NOTE 13

SCHED.
DEPTH
XV RC13B 10 4#5VIII, 4#5III 5#5XIII NOTE 2

7. HOOK 'XVI' BARS INTERSECTING WITH OPENING. (LIMIT NO. OF BARS INTERSECTING RM4 10 3#5IV, 3#5VII 6#5XIX NOTE 1,13 LANDSCAPE ARCHITECT
WITH OPENING TO THREE) RC14 10 7#5XIII 2#5VIII, 8#5III 2#5XV
XVI RM5 10 11#5XIII 6#5IV, 5#5XII 11#5II SWA Group
PLACE PORTION OF 8. HOOK INTERCEPTING SMALLER BARS SCHEDULED AT OPENING AND PLACE LARGER RC15 10 8#5III 10#6XVI NOTE 4 2001 Irving Boulevard, Suite 157
SCHED. COL. BARS SCHEDULED RUNNING CONTINUOUS ADJACENT TO OPENING. 0.33 L1c 0.33 L3c RC16 10 2#5XVIII 8#6III NOTE 1,9 RM6 10 6#5IV, 5#5VII 11#5II Dallas, TX 75207
STRIP REINF. 9. HOOK BOTTOM BARS AT STEP IN SLAB BOTTOM. RC17 8 8#5III 5#7XVI RM7 10 6#5IV, 5#5VII 11#5II (214-954-0016 Chuck McDaniel)
WHICH FALLS 10. ATLEAST TWO SCHEDULED TOP AND BOTTOM BARS SHALL BE PLACED WITHIN XVII RM8 10 6#5IV, 5#5VII 11#5II
WITHIN DEEP RC18 8 2#5VIII, 6#5III 8#5XIII STRUCTURAL
SHEARWALL REINFORCEMENT 0.5L2c 0.5L3c RM9 10 6#5IV, 5#5VII 11#5II
"BEAM" AT 11. PLACE LARGER BAR SCHEDULED ADJACENT TO OPENING CLASS B RC19 10 6#5XIII 2#5VIII, 8#5III NOTE 9,12 Datum Engineers
BOTTOM OF BEAM SPLICE/2 RC20 8 6#5XX 6#5XIX NOTE 2 RM10 10 6#5IV, 5#5VII 11#5II 6516 Forest Park Road
12. HOOKED BOTTOM BARS 'VIII' SHALL BE CONTINUOUS (SPLICED) THROUGH THE
SCHED. SHEARWALL RC21 10 8#5XIII 2#5VIII, 10#5III NOTE 12,9 RM11 10 6#5IV, 5#5VII Dallas, TX 75235
13. SCHEDULE BARS WITH COLUMN SUPPORTS ALONG GRIDLINE 'C'. RM12 10 6#5IV, 5#5VII 11#5XVI (214-358-0174 Rodolfo D'Arlach)
WIDTH RC22 8 8#5XX 8#5XIX NOTE 2
14. HOOK BARS INTERCEPTING WITH OPENINGS. XVIII RM13 10 6#5IV, 5#5VII 11#5XIII
0.5L2c NOTE MEP ENGINEER
15. LAP SPLICE INTERCEPTING BARS WITH BEAM TOP BARS IN ADJACENT SPAN. RC23 10 8#5XIII 2#5VIII, 10#5III 10#6XVII RM14 10 9#5XIII 5#5IV, 5#5VII
9,10,12,14 ME Engineers, Inc.
CLASS B RC25 10 12#4XIII 2#6VIII, 10#6III 12#6XVII NOTE 9,14 5#5XVI, 1825 Market Center Blvd., Suite 600
SLAB EDGE OR RM15 10 5#5VII, 4#8IV NOTE 6,8
SPLICE/2 RC26 10 7#7XIII 2#5VIII, 7#5III 5#8XVI Dallas, TX 75207
CANT. END. RM16 10 5#5XIII 4#5IX, 4#5XII NOTE 6 (214-741-1589 Drew Shivley)
RC27 10 6#5III 4#7XIX
2" RC28 8 6#4III NOTE 1 RM17 8 5#5IV, 5#5VII 13#5XVI ELEVATOR CONSULTANT
BEAM OR DROPPED SLAB CONTINUOUS BETWEEN SUPPORTS
RC29 10 12#5XIII 2#5VIII, 12#5III RM18 8 6#5IV, 6#5VII 9#5XIII Persohn | Hahn Associates, Inc.
TYPICAL DETAIL 11#5XIX, RM19 10 8#5XIII 5#5IX, 5#5XII 10#5XVII 8612 Broad Meadow Lane
NO SCALE
B D XIX RC30 10 12#5III
5#6XIX
NOTE 5,8 RM20 10 4#5XIII 3#5IX, 3#5XII 6#5XVI McKinney, TX 75071
RC31 8 12#4III 4#4XIV NOTE 5 RM21 10 8#5XII 5#5IX, 5#5XII 10#5XVII NOTE 14
RC32 10 12#5XIII 2#5VIII, 12#5III RM22 10 8#5XIII 5#5IX, 5#5XII 10#5XVII INTERIOR DESIGNER
NOTES:
0.33L1C OR 0.33L2C RM22A 10 8#5XIII 5#5IX, 5#5XII 8#5XIII Rottet Studio
1. SCHEDULED BEAM & SLAB REINF. NOT SHOWN. 4#6XIX,
WHICHEVER IS GREATER RC33 10 14#5III NOTE 11 808 Travis Street, Suite 100
2. REINF. SHOWN IN THIS DETAIL SHALL BE PLACED BENEATH 8#5XIX RM23 10 18#5XIII 9#5IX, 9#5XII
Houston, TX 77002
SCHED. TOP REINF. AND ABOVE SCHED. BOT. REINF. RC34 8 12#4III RM24 10 9#5IV, 9#5VII 18#5XIX (713-221-1830 x 6105 Anja Majkic)
EXTEND BARS FULL RC35 10 8#5XIII 2#5VIII, 12#5III NOTE 12 RM25 8 18#4IX
SLAB LENGTH OF SPAN IN
DIRECTION OF SLAB XX RC36 10 8#5III 8#5XIX NOTE 2,9 RM26 10 9#5XIII 5#5IX, 5#5XII
SPAN
MIN.
SPAN 2" RC37 8 8#4III RM27 10 8#5III 8#5XIX NOTE 5,14

RC38 10 9#5XIII 2#5VIII, 12#5III NOTE 9 RM28 8 8#4IX 6#4XIV
XXI 6"
#5 x 4'-0" EACH RC39 8 9#5XX 9#5XIX RM29 10 12#5XIII 6#5IX, 6#5XII
MIN. www.datumengineers.com | Co. Reg. No. F-2819
FACE, EACH CORNER. Dallas Austin San Antonio
SC1 10 8#5XIII 8#5III 5#5I, 4#5II NOTE 1,2,13 RM30 10 6#5IV, 6#5VII 12#5XIX 214-358-0174 512-469-9490 210-858-2880
PLACE 0.5L1C
1 1/2" SC2 10 8#5III 4#5I, 4#5II NOTE 2,13 RM31 8 10#4IX Datum Project No. 19166
INSIDE OF OTHER
CLR. CLASS B
2 SLAB REINFORCING. SC3 10 8#5III 5#5I, 4#5II NOTE 2,13 RM32 10 6#5XIII 4#5IX, 4#5XII DATE ISSUE TITLE
L/ SPLICE/2 SC4 10 8#5III 8#5XIII NOTE 1,2,13 RM33 8 8#4XX 8#5XIX 04/03/2020 SCHEMATIC DESIGN PRESENTATION
PROVIDE EXTRA BARS IN FLAT SLAB BAR TYPES SC5 10 6#6XIX 6#5III NOTE 1,2,3 RM34 10 8#5XIII 5#5IX, 5#5XII
5'

"
-0
EACH LAYER, EQUAL TO AREA SC6 10 6#5III 3#7I, 3#7II NOTE 2 RM35 8 10#4XX 10#5XIX
-0
TYPICAL DETAIL
"
5'

OF INTERRUPTED BARS (1#5 SC7 10 6#6III 3#8I, 3#8II NOTE 2 SM1 10 8#5XIII 4#5IX, 4#5XII 9#5II NOTE 1,13 10/30/2020 ISSUE FOR PERMIT
EACH FACE EACH SIDE
NO SCALE SC8A 10 6#8XIII 6#6VIII SM2 10 4#5IV, 4#5VII 8#5II NOTE 13 12/18/2020 90% CONSTRUCTION DOCUMENTS
MINIMUM). LENGTH SAME AS
INTERRUPTED SCHED. BARS. SC8B 10 6#6III SM3 10 4#5IV, 4#5VII 9#5II NOTE 13 01/25/2021 100% CONSTRUCTION DOCUMENTS
L
SC9A 10 6#5III 6#9XVI NOTE 5,7 SM4 10 4#5IX, 4#5XII 8#5XIII NOTE 1,13
SC9B 10 6#5III 6#8XVI SM05 10 11#5XIX 11#5III NOTE 1
SC10A 10 3#9XIV 6#5III NOTE 4,5 SM06 10 11#5III 11#5II
TYPICAL SLAB SC10B 10 6#5III SM07 10 11#5III 11#5II
#4 AT 12" TOP REINFORCING SC11B 10 6#5VIII 6#8XIX NOTE 1,2 SM8A 10 9#5XIII 5#5IX, 4#5XII
PLAN NOTE: SC12 10 6#8XIII 2#7VIII, 7#5III SM08B 10 12#5III
#4 AT 12" BOT. EXTRA BARS MAY BE OMITTED SC13 10 9#5III 9#8XVI 5#5XVI,
SM9A 10 5#5VII, 4#8IV NOTE 6,8
WHERE SIDES OF OPENING ARE SC14 10 9#6III NOTE 9 3#8XVI
FRAMED BY BEAMS. SC15 8 2#7VIII, 7#5III 5#8XIX NOTE 1,2 SM9B 10 12#5III 14#5XVI
SC16 10 10#5XIII 2#6VIII, 10#6III 5#8XIII NOTE 1,4,9,12 SM10A 10 5#5XIII 5#5IX, 7#5XII 11#5XIII NOTE 1
SC17 8 2#4VIII, 3#4III 5#8XIX NOTE 1,2,12 SM10B 10 12#5III
SPECIAL CORNER SLAB REINFORCING REINFORCING AT SMALL SLAB OPENING
BASEMENT SC18 10 7#6XIII 2#6VIII, 9#6III NOTE 1,9.10 SM11B 10 12#5III 11#5XIX NOTE 1
TYPICAL DETAIL WALL TYPICAL DETAIL SC19 8 2#4VIII, 4#4III 7#10XIX NOTE 1,10 SM16 10 4#5XII 5#6IX, 4#6XII NOTE 9
NO SCALE
OR SPANDREL
BEAM C NO SCALE F SC20
SC21
10
10
12#4XIII
9#7XIII
2#8VIII, 8#8III
2#6VIII, 4#6III
8#8XVII NOTE 1,9
NOTE 1
SM17
SM18
8
10 6#5XIII
3#4IX, 2#4XII
3#6IX, 3#6XII
5#4XIX
6#7XIII
NOTE 1
NOTE 1 REV. DATE ISSUE TITLE
SC22 10 6#5VIII 6#9XIX NOTE 1,2,9 SM20 10 10#5XIII 7#6IX, 7#6XII 10#8XVII NOTE 14 .05 12/18/2020 Permit Set Update
NOTE:
SC23 8 6#5III NOTE 1 SM20A 10 8#7XIII 5#6IX, 5#6XII 8#7XIII
COLUMN REINFORCEMENT
NOT SHOWN FOR CLARITY. SC24 10 12#7XIII 2#6VIII, 12#6III SM21 10 21#5XIII 9#6IX, 9#6XII
SC25 10 14#5VIII 12#8XIX NOTE 9 SM22 10 11#5IV, 11#5VII 21#5XIX NOTE 9
SC26 8 12#5III NOTE 1 SM23 8 21#4IX NOTE 1
COLUMN STRIP COLUMN STRIP
SC27 10 12#5XIII 2#6VIII, 14#6III NOTE 1 SM24 10 8#5XIII 7#5IX, 7#5XII
SEE PLAN SEE PLAN SM25 10 4#5IV, 4#5VII 12#5XIX NOTE 9
6#8XIX,
SC28 10 14#5VIII NOTE 9,11
6#9XIX SM26 8 12#4IX NOTE 1
SC29 8 12#5III NOTE 1 SM27 10 18#5XIII 8#6IX, 8#6XII NOTE 1
COLUMN STRIP SC30 10 8#6XIII 2#7VIII, 10#7XI 3#9XIII NOTE 1,4,9,12 SM28 10 6#5IV, 6#5VII 18#5XIX NOTE 9
REINF. SEE SCHED.
SC31 10 8#5VIII 6#10XIX NOTE 1,9,10 SM29 8 18#4IX
SC32 8 8#5III NOTE 1 SM33A 8 5#5II 7#5IV 5#5II NOTE 2
SC33 8 8#6III 8#7XVI NOTE 2 SM33B 8 12#5II 12#5IV 12#5XIII
SC34 8 2#6VIII, 5#6III 9#6XIX NOTE 1 SM34 8 5#5XX 5#5XIX NOTE 1
SC35 8 2#8VIII, 2#8III 4#10XIX NOTE 1,10 SM35 8 16#5XX 16#5XIX
COLUMN STRIP
REINF., SEE SCHED
2"
SCHED. BEAM REINF.
COLUMN OR
MAPLE TERRACE
SHEARWALL SEE PLAN 3001 MAPLE AVENUE
J K CONC 2-WAY FLAT SLAB W
H
DROP PNL SCHED & DETAILS
CONCRETE TWO-WAY FLAT SLAB WITH DROP PANEL SCHEDULE AND DETAILS 190013
PROJECT NUMBER
CURTAIN WALL
SEE ARCH'L
SHEAR WALL
SEE PLAN
SEE PLAN AND S501-OF
SLAB DEVELOPER
CONNECTION AND SEE PLAN
EMBED BY CURTAIN Hines
EXISTING SLAB SLAB 2200 Ross Avenue, Suite 4200W
WALL MFR. BUILDING SEE PLAN SEE PLAN SEE PLAN Dallas, TX 75201
SCHED. DEPTH
SCHED. DEPTH
EXTEND BEAM
SCHED. DEPTH
E.J. E.J. E.J.
T.O.S.C. EL. SEE PLAN SEE PLAN SEE PLAN SLAB SCHED, TOP REINF. 2800 Post Oak Blvd., 49th Floor
SEE PLAN SEE PLAN TO EDGE OF SLAB Houston, TX 77056
EXISTING FRAMING (713-621-8000 Juan Delgado)
EXISTING BUILDING
SCHED. DEPTH
EQUITY PARTNERS
T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL. McNair Interests
SEE PLAN SEE PLAN SEE PLAN 109 N. Post Oak Lane, Suite 600
Houston, TX 77024
SCHED.
DEPTH
(Drew Steffen)

(David Leff)
BEAM
SEE PLAN 5G Studio Collaborative, LLC.
SCHED. WIDTH Dallas, TX 75202
COLUMN BEYOND (214-347-4982 Christine Robbins-Elrod)
SEE PLAN
3/4" = 1'-0" 1 3/4" = 1'-0" 2 3/4" = 1'-0" 3 3/4" = 1'-0" 5 GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
SEE DETAIL H/S403-OF FOR 3904 Elm Street, Suite B
ADDITIONAL BARS REQUIRED FOR Dallas, TX 75226
INCREASED BEAM WIDTH. (214-824-7949 Robert Baldwin)
SEE PLAN SEE PLAN SEE PLAN SEE PLAN GEOTECH

ECS Southwest, LLP
SHEAR WALL Carrollton, TX 75006
SEE PLAN (972-392-3222 Siddharth Neekhra)
SEE PLAN
AND S501-OF
SLAB CIVIL ENGINEER
E.J. SEE PLAN SEE PLAN Kimley-Horn and Associates, Inc.
SEE PLAN 13455 Noel Road, Two Galleria Office Tower, Suite 700
SCHED. DEPTH
SCHED. DEPTH
E.J.
SCHED. DEPTH
SLAB, SEE PLAN LANDSCAPE ARCHITECT
SEE PLAN SWA Group
EXISTING FRAMING EXISTING FRAMING SLAB 2001 Irving Boulevard, Suite 157
SEE PLAN SEE PLAN SEE PLAN STRUCTURAL
SCHED. DEPTH
SCHED. DEPTH
Datum Engineers
Dallas, TX 75235
ELEVATOR SHAFT
MEP ENGINEER
ME Engineers, Inc.
SCHED. WIDTH 1825 Market Center Blvd., Suite 600
BEAM BEAM BEYOND Dallas, TX 75207
SEE PLAN BEAM SCHED. BEAM (214-741-1589 Drew Shivley)
SEE PLAN
SEE PLAN BEAM WIDTH BEYOND
McKinney, TX 75071
3/4" = 1'-0" 7 3/4" = 1'-0" 9 3/4" = 1'-0" 10 INTERIOR DESIGNER

Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
SEE PLAN
SEE PLAN COLUMN BEYOND www.datumengineers.com | Co. Reg. No. F-2819
SEE PLAN 214-358-0174 512-469-9490 210-858-2880
E.J. Datum Project No. 19166

E.J. SLAB SEE PLAN SEE PLAN DATE ISSUE TITLE
SEE PLAN SEE PLAN
SCHED. DEPTH
SCHED. DEPTH
SEE PLAN
SCHED. DEPTH
EXIST. STRUCTURE
SCHED. DEPTH

E.J.
SEE PLAN SLAB 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SEE PLAN EXISTING FRAMING 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
EXISTING FRAMING
T.O.S.C. EL. SEE PLAN 01/25/2021 100% CONSTRUCTION DOCUMENTS
SEE PLAN
SEE PLAN
SCHED. DEPTH
BEAM DROP PANEL BEYOND DROP PANEL

SCHED. WIDTH
3/4" = 1'-0" 12 3/4" = 1'-0" 14 3/4" = 1'-0" 15

DROP PANEL SEE PLAN SEE PLAN

SEE PLAN SEE PLAN
SLAB SEE PLAN

SLAB
SEE PLAN SEE PLAN
SEE PLAN SEE PLAN SLAB
SEE PLAN
SCHED. DEPTH
SCHED. DEPTH SEE PLAN
SEE PLAN
PLAN
SEE
T.O.S.C. EL.
T.O.S.C. EL. T.O.S.C. EL. SEE PLAN
SCHED. DEPTH
SEE PLAN SEE PLAN
SCHED. DEPTH
SEE PLAN
BEAM
SEE PLAN
SEE PLAN
BEAM
SEE PLAN SCHED. WIDTH
SCHED. WIDTH MAPLE TERRACE
COL. DROP PANEL 3001 MAPLE AVENUE
18 SEE PLAN SEE 1/S405-OF DALLAS, TEXAS, 75201
S410-OF
SECTIONS AND DETAILS
SEE PLAN SEE PLAN
PLAN 1/4" = 1'-0" 16 3/4" = 1'-0" 18 3/4" = 1'-0" 19 3/4" = 1'-0" 20 190013
PROJECT NUMBER
HANDRAIL
SEE PLAN SEE ARCH'L
SEE PLAN SEE PLAN
E.J. SEE PLAN E.J. E.J. DEVELOPER

SEE PLAN SEE PLAN SEE PLAN Hines
SLAB SLAB 2200 Ross Avenue, Suite 4200W
SLAB SEE PLAN SEE PLAN
SCHED. SLAB
Dallas, TX 75201
SCHED. SLAB
L4X4X1/2 X CONT.
SCHED. SLAB
SCHED. SLAB
DEPTH
W/ 1/2" DIA. X 6" H.S.
DEPTH
DEPTH
DEPTH
EXISTING FRAMING EXISTING FRAMING AT 1'-6" O.C. EXISTING FRAMING 2800 Post Oak Blvd., 49th Floor
Houston, TX 77056
SEE PLAN SEE PLAN SEE PLAN EQUITY PARTNERS
SCHED. DEPTH
SCHED. DEPTH
McNair Interests
Houston, TX 77024
(Drew Steffen)

BEAM BEAM (David Leff)
SEE PLAN SEE PLAN
SCHED. WIDTH SCHED. WIDTH OFFICE/RETAIL ARCHITECT
Dallas, TX 75202
3/4" = 1'-0" 2 3/4" = 1'-0" 4 3/4" = 1'-0" 5 MASTER/MULTIFAMILY ARCHITECT

GFF Architects
Dallas, TX 75201
SEE PLAN ZONING/ENTITLEMENT

Baldwin Associates
HANDRAIL SEE PLAN 3904 Elm Street, Suite B
SEE PLAN SEE ARCH'L HANDRAIL CURTAIN WALL Dallas, TX 75226
E.J. SEE ARCH'L SEE ARCH'L (214-824-7949 Robert Baldwin)
FINISH SEE PLAN
SEE PLAN
SEE ARCH'L END OF TREAD
GEOTECH
1/4 3-12
SLAB SLAB ECS Southwest, LLP
SEE ARCH'L SEE ARCH'L 3033 Kellyway Drive, Suite 110
SEE PLAN SEE PLAN L6X4X1/2 (LLV)
EXISTING FRAMING Carrollton, TX 75006
W/ EMBED PL.3/4 X 9" X CONT. CONNECTION AND SLAB (972-392-3222 Siddharth Neekhra)
W/2-3/4" DIA. X 6" H.S. AT 12" EMBED BY CURTAIN SEE PLAN
CONNECTION BY STAIR T.O.S.C. EL. WALL MFR. CIVIL ENGINEER
SEE ARCH'L
T.O.S.C. EL.
SUPPLIER SEE PLAN
SCHED. DEPTH
SCHED. DEPTH
2#7 ADDN'L BOT.
6"
BARS X OPENING (PERFORMANCE SPEC.) T.O.S.C. EL. 13455 Noel Road, Two Galleria Office Tower, Suite 700
WIDTH +1'-6"
SCHED. DEPTH
T.O.S.C. EL. L6X3 1/2X1/2X CONT. (LLV)

SEE PLAN WITH 1/2" X 2'-6" D.B.A. @ 18". LANDSCAPE ARCHITECT
PROVIDE 2 ADDN'L D.B.A.'S SWA Group
SCHED. SLAB
@ 6" AT STAIR STRINGER BEAM 2001 Irving Boulevard, Suite 157
AT STAIR, PROVIDE
SCHED. SLAB
DEPTH
LOCATIONS SEE PLAN Dallas, TX 75207
PL.3/4" 18" X 8'-6"
DEPTH
4" 3" 11/S610A-OF (214-954-0016 Chuck McDaniel)

BEAM W/ 2-3/4" DIA. X 6" H.S.
SLAB
SEE PLAN SEE PLAN AT 12" O.C.
SEE PLAN STRUCTURAL
STAIR FRAMING Datum Engineers
4"
SCHED. WIDTH (PERFORMANCE SPEC.) 6516 Forest Park Road
3'-0" Dallas, TX 75235
#3 X @ 12"
1'-6"
MEP ENGINEER
4"
ME Engineers, Inc.
3/4" = 1'-0" 6 3/4" = 1'-0" 7 3" TYP. 1'-0" 1'-0" 3/4" = 1'-0" 9 3/4" = 1'-0" 10 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
ELEVATOR CONSULTANT
McKinney, TX 75071
CURTAIN WALL
SEE PLAN
SEE PLAN
SEE PLAN INTERIOR DESIGNER
SEE PLAN SEE PLAN Rottet Studio
CURTAIN WALL
SCHED. SLAB
Houston, TX 77002
SCHED. SLAB
10/S411-OF
SCHED. SLAB
SEE ARCH'L
SCHED. SLAB
(713-221-1830 x 6105 Anja Majkic)
DEPTH
DEPTH
SLAB
DEPTH
DEPTH
SLAB
10/S411-OF 10/S411-OF SEE PLAN
SEE PLAN
T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL.

SCHED. BEAM

DEPTH
214-358-0174 512-469-9490 210-858-2880
SCHED. SLAB
SCHED. SLAB
DATE ISSUE TITLE
DEPTH
SCHED. BEAM
SCHED. BEAM
DEPTH
DEPTH
DEPTH
SCHED. BEAM 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT

WIDTH
CURTAIN WALL BEAM
SEE ARCH'L SEE PLAN CURTAIN WALL 12/18/2020 90% CONSTRUCTION DOCUMENTS
SEE ARCH'L 01/25/2021 100% CONSTRUCTION DOCUMENTS
BEAM BEAM
SCHED. BEAM SEE PLAN SEE PLAN
WIDTH
3/4" = 1'-0" 11 3/4" = 1'-0" 12 3/4" = 1'-0" 13 3/4" = 1'-0" 14

COLUMN
CURTAIN WALL CURTAIN WALL SEE PLAN AND
SEE ARCH'L SEE ARCH'L F/S401-OF CURTAIN WALL SEE PLAN
SCHED. DEPTH
SEE ARCH'L
E.J. E.J. REV. DATE ISSUE TITLE
SEE PLAN SLAB SEE PLAN EXISTING .05 12/18/2020 Permit Set Update
IPE DECK SEE PLAN IPE DECK PARAPET
T.O.S.C. EL.
T.O.S.C. EL. T.O.S.C. EL. SEE PLAN
SEE PLAN SEE PLAN
SCHED. BEAM DEPTH
SCHED. DEPTH
SCHED. DEPTH
BEAM (HIGH) BEAM

SEE PLAN SEE PLAN
BEAM
BEAM SCHED. BEAM WIDTH SEE PLAN
STUD CLOSURE WALL SEE PLAN
SEE ARCH'L
BEAM
BEAM (LOW) SEE PLAN
SEE PLAN STUD CLOSURE WALL
STUD CLOSURE WALL SEE ARCH'L ROOFING
ROOFING SEE ARCH'L SEE ARCH'L
ROOFING EXISTING FRAMING
SEE ARCH'L SEE ARCH'L
EXISTING FRAMING EXISTING FRAMING MAPLE TERRACE
3001 MAPLE AVENUE
SHORE EXISTING STRUCTURE UNDER
SHORE EXISTING STRUCTURE UNDER NEW CONSTRUCTION UNTIL CONCRETE
NEW CONSTRUCTION UNTIL CONCRETE SHORE EXISTING STRUCTURE UNDER
HAS REACHED 28 DAY STRENGTH
3/4" = 1'-0" 16
NEW CONSTRUCTION UNTIL CONCRETE
HAS REACHED 28 DAY STRENGTH 3/4" = 1'-0" 17
HAS REACHED 28 DAY STRENGTH
3/4" = 1'-0" 18 190013
PROJECT NUMBER
NOTE: MAX. SLEEVE NOTES:
COORDINATE EMBEDS SCHED. OR DETAILED TOP & BOT. BEAM WIDTH 1. MAX SLEEVE DIAMETER IS 6"
DIAMETER SEE MECH'L DWGS FOR
WITH FINAL ELEVATOR REINF. INSTALL SLEEVE FIRST.
UP TO 36" 6" 2. MIN. SPACING BETWEEN ADJACENT LOCATION. DO NOT LOCATE
CUT SHEETS POSITION T & B REINF. IN STRAIGHT
>36"-42" 8" SLEEVES IS 2'-6" LESS THAN 1/6 OF CONSTRUCTION JOINT
RUNS EA. SIDE OF SLEVE. DO NOT
SCHED. OR DETAILED STIRRUPS T&B MATCH SIZE AND THE BEAM SPAN FROM WITHIN
BUNDLE BARS WITH MORE THAN 2'-0" OF C.L. OF SPAN
SEE PLAN SEE BEAM STIRRUPS @ NUMBER OF VERTICAL LEGS AS FACE OF SUPPORT.
2 BARS PER BUNDLE
PLAN SPECIFIED SPACING SCHEDULED OR DETAILED STIRRUPS. 6" 6" 6" 6"
BEAM TOP REINF.
FINISH MACHINE BEAM BY SPACE STIRRUPS @ 3" O.C. MAX 4 ADDITIONAL DEVELOPER
MIN. DIAMETER MIN.

10"
SEE ARCH'L. ELEVATOR MFR. 1 1/2" COVER SCHEDULED OR DETAILED STIRRUPS
#6@6" O.C. HORIZ. Hines
1'-6" ON STEEL, TYP. BEAM STIRRUPS @
TOP & BOTTOM 2200 Ross Avenue, Suite 4200W
SCHED. SLAB
ALL SIDES.
SLEEVE
SPECIFIED SPACING. Dallas, TX 75201
THICKNESS
EMBED PL.3/4X18X1'-6"
DIAMETER
(2#6 MIN.)
SLEEVE
1/3 "D"
W/4-3/4" DIA. X 6" H.S.
"D" DEPTH OF BEAM

MIN.
1 1/2" COVER
Houston, TX 77056
ON STEEL, TYP.
10"
1/3 "D"
EQ. EQ.
T.O.S.C. EL. T.O.S.C. EL. ALL SIDES.
5" TYP.
SEE PLAN SEE PLAN EQUITY PARTNERS

STIRRUPS X EA SIDE OF SLEEVE. MATCH 3 ADDN'L. SCHED. OR DETAILED McNair Interests
1/3 "D"
SEE MECH'L 109 N. Post Oak Lane, Suite 600
T.O.S.C. EL. SIZE OF SCHED. OR DETAILED STIRRUPS. STIRRUPS @ 3" O.C. EA. SIDE
MIN.
DWGS FOR Houston, TX 77024
10"
VARIES PROVIDE 1 EA. SIDE OF SLEEVE WHERE 2 OF SLEEVE
ELEVATION (Drew Steffen)
SEE PLAN SLAB, LEG STIRRUPS ARE SPECIFIED IN THE BEAM
SEE PLAN AND 2 EA. SIDE WHERE 4 LEG STIRRUPS ARE NOTIFY ENGINEER FOR CONDITIONS ADD 3 ADD'L SCHEDULED 3 1/2" DEEP SHEAR KEY Mitsui Fudosan America
THAT EXCEED THE LIMITATIONS OF BEAM BOTTOM REINF. WIDTH = BEAM WIDTH - 6" 1251 Avenue of the Americas, Suite 800
ADD'L. #4 X @12" SPECIFIED. SPACE STIRRUPS AT 3" O.C. MAX. PLAN OR DETAILED BEAM STIRRUPS New York, New York 10020
W/3#5 X CONT. MIN. SPACING BETWEEN ADJACENT SLEEVES IS THIS TYP. DETAIL. @ 3" O.C. EA. SIDE OF EQ. EQ. 45 BAR (David Leff)
BEAM REINF.
2'-6". THE C.L. OF ADJACENT SLEEVES MUST SLEEVE SLEEVE CONTINUOUS THROUGH
DIA. (TYP)
SCHED. DEPTH
FINISH DIAMETER CONSTRUCTION JOINT ELEVATION OFFICE/RETAIL ARCHITECT

BEAM, ALIGN ALONG THE LENGTH OF THE BEAM. NO
SEE ARCH'L. NOTIFY ENGINEER FOR CONDITIONS 5G Studio Collaborative, LLC.
SEE PLAN MORE THAN ONE SLEEVE WITHIN THE WIDTH OF
THAT EXCEED THE LIMITATIONS OF ELEVATION 1217 Main St., Suite 500
SCHED. WIDTH THE BEAM. BEAM CONSTRUCTION JOINT Dallas, TX 75202
VERTICAL SLEEVE THROUGH BEAM THIS TYP. DETAIL. HORIZONTAL SLEEVE THROUGH BEAM OR JOIST (214-347-4982 Christine Robbins-Elrod)
TYPICAL DETAIL TYPICAL DETAIL TYPICAL DETAIL MASTER/MULTIFAMILY ARCHITECT

NO SCALE NO SCALE
NO SCALE GFF Architects
3/4" = 1'-0" 1 3/4" = 1'-0" 2 3 4 5 2808 Fairmount St., Suite 300
Dallas, TX 75201
ZONING/ENTITLEMENT
00 1 4 Baldwin Associates
SEE PLAN SEE PLAN (214-824-7949 Robert Baldwin)
GEOTECH
NOTE: ECS Southwest, LLP
SEE 15/S412-OF FOR 3033 Kellyway Drive, Suite 110
INFO. NOT SHOWN Carrollton, TX 75006
CIVIL ENGINEER
Dallas, TX 75240
LANDSCAPE ARCHITECT
T.O.S.C. EL. SWA Group
SEE PLAN 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
STRUCTURAL
Datum Engineers
Dallas, TX 75235
MEP ENGINEER
ME Engineers, Inc.
Dallas, TX 75207
COLUMN, (214-741-1589 Drew Shivley)
SEE PLAN
TYP. ELEVATOR CONSULTANT
ELEVATION McKinney, TX 75071

Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
00 2 3 5

STRAIGHT DRAPE AT 214-358-0174 512-469-9490 210-858-2880
CANTILEVER BEAM HIGH POINT C.G.S SHEAR WALL Datum Project No. 19166
TIE CONCRETE SEE PLAN
DATE ISSUE TITLE
COLUMNS, SEE PLAN
T.O.S.C. EL.
SEE PLAN
LIVE ANCHOR END. DEAD ANCHOR RESERVED FOR REVIEWERS NOTES

C.G.S OF TENDONS AT END. C.G.S OF TENDONS
BEAM MID-DEPTH AT BEAM MID-DEPTH
SHEAR WALL
TIE CONCRETE SEE PLAN
COLUMNS, SEE PLAN
ELEVATION 1/2" = 1'-0" 15

00 2 3 5
NOTE:
SEE 15/S412-OF FOR
INFO. NOT SHOWN
SHEAR WALL
SEE PLAN
T.O.S.C. EL.
SEE PLAN
COLUMN, MAPLE TERRACE

SEE PLAN
3001 MAPLE AVENUE
TYP.
ELEVATION
1/2" = 1'-0" 20 190013 S412-OF

PROJECT NUMBER S H E E T N U M B E R
DEVELOPER
Hines
Dallas, TX 75201
ROOFING (972-716-2908 Corbin Eckel)
T.O.S.C. EL. SEE PLAN
SEE PLAN SEE ARCH'L. SEE PLAN
SEE PLAN SEE PLAN 2800 Post Oak Blvd., 49th Floor
SLAB Houston, TX 77056
CONNECTION AND SEE PLAN (713-621-8000 Juan Delgado)
EMBED BY CURTAIN
WALL MFR. SLAB J/S401-OF EQUITY PARTNERS
SLAB
T.O.S.C. EL. SEE PLAN SEE PLAN T.O.S.C. EL. SLAB McNair Interests
SEE PLAN SEE PLAN SEE PLAN Houston, TX 77024
(Drew Steffen)
SCHED. BEAM DEPTH

VARIES SEE PLAN Mitsui Fudosan America
SCHED.
DEPTH
SEE PLAN 1251 Avenue of the Americas, Suite 800
SCHED. SLAB
SCHED.
DEPTH
SCHED.
DEPTH
DEPTH
CURTAIN WALL (David Leff)
SCHED. SLAB
SEE ARCH'L
SCHED.
DEPTH
DEPTH
CONNECTION AND 5G Studio Collaborative, LLC.
EMBED BY CURTAIN 2/S413-OF 1217 Main St., Suite 500
CURTAIN WALL
WALL MFR. Dallas, TX 75202
SEE ARCH'L (214-347-4982 Christine Robbins-Elrod)
BEAM, COLUMN BEAM BEAM
SCHED WIDTH
SEE PLAN SEE PLAN SEE PLAN SEE PLAN MASTER/MULTIFAMILY ARCHITECT
CURTAIN WALL CURTAIN WALL
SCHED. BEAM WIDTH SEE ARCH'L GFF Architects
3/4" = 1'-0" 1 3/4" = 1'-0" 2 3/4" = 1'-0" 3 SEE ARCH'L
3/4" = 1'-0" 4 2808 Fairmount St., Suite 300
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
Dallas, TX 75226
MU = 45,000 LB-FT.
FU = 5,000 LBS
IN ANY DIRECTION GEOTECH
ECS Southwest, LLP
SLAB Carrollton, TX 75006
SCHED. SLAB

DEPTH
DAVIT BASE AND DAVIT BASE AND PU=5,000 LBS CIVIL ENGINEER
BASEPLATE BASEPLATE MU = 10,000 LB-FT Kimley-Horn and Associates, Inc.
BY DAVIT MFR. BY DAVIT MFR. IN ANY DIRECTION 13455 Noel Road, Two Galleria Office Tower, Suite 700
T.O.S.C. EL. ROOF SAFETY ANCHOR SEE PLAN Dallas, TX 75240
SEE PLAN HOOK BARS AT AND BASEPLATE (972-770-1300 Alex Rathbun)
DISCONTINUOUS A
ADDN'L 4#5 X 6'-0" E.W. A
ADDN'L 4#5 X 6'-0" CENTERED BY ANCHOR MFR.
ENDS TOP & BOT. CENTERED ON DAVIT W/ 4#5 X LANDSCAPE ARCHITECT
ON DAVIT
2'-0"
SWA Group
T.O.S.C. EL. SLAB 2001 Irving Boulevard, Suite 157
ADDN'L 4#5 X 6'-0" E.W.
SCHED. BEAM
T.O.S.C. EL. T.O.S.C. EL. SEE PLAN SEE PLAN Dallas, TX 75207
TOP & BOT. CENTERED (214-954-0016 Chuck McDaniel)
DEPTH
SEE PLAN SEE PLAN ON ANCHOR POINT

STRUCTURAL
T.O.S.C. EL.
SCHED.
Datum Engineers
DEPTH
SCHED.
DEPTH
Dallas, TX 75235
SCHED.
DEPTH
BEAM (214-358-0174 Rodolfo D'Arlach)
SEE PLAN
SCHED
DEPTH
MEP ENGINEER
2/S413-OF ME Engineers, Inc.
SCHED. BEAM WIDTH DROP PANEL Dallas, TX 75207
SEE PLAN SCHED. WIDTH (214-741-1589 Drew Shivley)
DAVIT AT SLAB DROP PANEL DAVIT AT BEAM ELEVATOR CONSULTANT

CURTAIN WALL
3/4" = 1'-0" 6 1" = 1'-0" 8 1" = 1'-0" 9 SEE ARCH'L 3/4" = 1'-0" 10 Persohn | Hahn Associates, Inc.
McKinney, TX 75071
SEE PLAN SEE PLAN
EL. = 599'-4" NOTE: NOTE: INTERIOR DESIGNER
COAT ALL WELDS WITH SEE 11/S413-OF FOR Rottet Studio
NOTE: COLD GALV. COMPOUND 808 Travis Street, Suite 100
6"
EMBED. PL. CAN BE 11 INFO. NOT SHOWN.

AFTER WELDING Houston, TX 77002
2"
T.O.S. EL. SHIFTED SO THAT IT IS TAB PL.3/8" X 4" X 0'-4"

S413-OF (713-221-1830 x 6105 Anja Majkic)
SEE PLAN NOT CENTERED ON COL.
PREFAB HORIZ. AT OPNG. CONDITION. NOTE:
PREFAB HORIZ.
SCREEN, SEE ARCH'L ALL STEEL TO
SCREEN, SEE ARCH'L 1/4
HSS BEAM W.P. 3 SIDES, TYP. BE GALVANIZED PREFAB HORIZ.
HSS BEAM HIGH 1/4 SCREEN, SEE ARCH'L
SEE PLAN
1'-0"
SEE PLAN www.datumengineers.com | Co. Reg. No. F-2819
214-358-0174 512-469-9490 210-858-2880
X3
TYP Datum Project No. 19166
PL
/4
1/4 3 T.O.S. EL. T.O.S. EL.
.1
.1
PL
DATE ISSUE TITLE
SEE PLAN
/4
9'-8"
SEE PLAN
X3
FINISH STRAP PL. 04/03/2020 SCHEMATIC DESIGN PRESENTATION
SEE ARCH'L SEE PLAN HSS BEAM NOTE: 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
SEE PLAN 1/4 PL.3/4X12X1'-0" W/ COAT ALL WELDS 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
4-3/4" DIA. X 6" H.S. WITH COLD GALV. 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
COMPOUND AFTER HSS BEAM
NOTE: SEE PLAN
ALL STEEL TO WELDING

T.O.S.C. EL. HSS BEAM 12/18/2020 90% CONSTRUCTION DOCUMENTS
BE GALVANIZED SEE PLAN LOW 01/25/2021 100% CONSTRUCTION DOCUMENTS
BEAM
POST SEE PLAN
W.P. 1/4 SEE PLAN
SEE PLAN
HSS BEAM L4X4X1/2 X 0'-4"
HSS BEAM RESERVED FOR REVIEWERS NOTES
SEE PLAN W/1/4" STIFF. PL.
SEE PLAN L4X4X5/16 X 0'-9", TYP.
STRAP PL. 1 1/2" TYP. 12/S413-OF
6"
2'-0"
SEE PLAN TYP.
1/4
ROOFING T.O.S.C. EL. POST

SEE ARCH'L. TYP. VARIES SEE PLAN
1/4 SEE PLAN
SLAB
SEE PLAN 12/S413-OF
T.O.S.C. EL.
VARIES
SEE PLAN 1" = 1'-0" 12 3/8" = 1'-0" 13 1" = 1'-0" 14 1" = 1'-0" 15
1" = 1'-0" 11 NOTE:

SEE 14/S413-OF FOR
INFO. NOT SHOWN.

NOTE:
SEE 14/S413-OF FOR
INFO. NOT SHOWN. PREFAB HORIZ. PREFAB HORIZ.
SCREEN, SEE ARCH'L SCREEN, SEE ARCH'L
T.O.S. EL. T.O.S. EL.

SEE PLAN SEE PLAN
BEAM 17/S413-OF COLUMN BEAM

SEE PLAN
SEE PLAN SEE PLAN 1/4 6
12/S413-OF
T.O.S.C. EL.
SEE PLAN CAP PL.
19/S621-OF SIM
COLUMN
SEE PLAN
MAPLE TERRACE
3001 MAPLE AVENUE
PENTHOUSE ROOF
SEE PLAN SECTIONS AND DETAILS
16 17
1" = 1'-0" 1" = 1'-0"
190013
PROJECT NUMBER
DEVELOPER
B A E1 1 2 3 4 5SCREEN TOS B A Hines
601'-5" Dallas, TX 75201
SEE PLAN SEE PLAN (972-716-2908 Corbin Eckel)
SEE PLAN SEE PLAN SEE PLAN SEE PLAN 2800 Post Oak Blvd., 49th Floor
Houston, TX 77056
EQUITY PARTNERS
ROOF ROOF ROOF McNair Interests
589'-2" 589'-2" 589'-2" 109 N. Post Oak Lane, Suite 600
Houston, TX 77024
(Drew Steffen)

(David Leff)
LEVEL 09 LEVEL 09 LEVEL 09 1217 Main St., Suite 500
573'-2" 573'-2" 573'-2" Dallas, TX 75202
GFF Architects
SHEAR WALL REINFORCING SCHEDULE 2808 Fairmount St., Suite 300
Dallas, TX 75201
SW-1 SW-2 SW-3 ZONING/ENTITLEMENT
BOUNDARY BOUNDARY BOUNDARY BOUNDARY BOUNDARY BOUNDARY Baldwin Associates
VERT. REINF. HORIZ. REINF. ELEMENT NORTH ELEMENT SOUTH VERT. REINF. HORIZ. REINF. ELEMENT EAST ELEMENT WEST VERT. REINF. HORIZ. REINF. ELEMENT NORTH ELEMENT SOUTH
LEVEL 08 LEVEL 08 LEVEL 08 3904 Elm Street, Suite B
557'-2" 557'-2" 557'-2" Dallas, TX 75226
LEVEL 9 TO ROOF #4@12" #4@12" #4@12" #4@12" #4@12" #4@12" (214-824-7949 Robert Baldwin)
14#7 (T) 16#7 (T) 8#7 (T) 8#7 (T) 14#7 (T) 14#7 (T)
GEOTECH
LEVEL 8 TO 9 #4@12" #4@12" 14#7 (T) 16#7 (T) #4@12" #4@12" 8#7 (T) 8#7 (T) #4@12" #4@12" 14#7 (T) 14#7 (T) ECS Southwest, LLP
LEVEL 7 TO 8 #4@12" #4@12" 14#7 (T) 16#7 (T) #4@12" #4@12" 8#7 (T) 8#7 (T) #4@12" #4@12" 14#7 (T) 14#7 (T) (972-392-3222 Siddharth Neekhra)
LEVEL 6 TO 7 #4@12" #4@12" #4@12" #4@12" #4@12" #4@12" CIVIL ENGINEER

14#7 (T) 16#7 (T) 8#7 (T) 8#7 (T) 14#7 (T) 14#7 (T)
LEVEL 07 LEVEL 07 LEVEL 07 13455 Noel Road, Two Galleria Office Tower, Suite 700
541'-2" 541'-2" 541'-2" LEVEL 5 TO 6 #4@12" #4@12" 14#7 (T) 16#7 (T) #4@12" #4@12" 8#7 (T) 8#7 (T) #4@12" #4@12" 14#7 (T) 14#7 (T) Dallas, TX 75240
12" THICK LEVEL 4 TO 5 #4@12" #4@12" #4@12" #4@12" #4@12" #4@12" LANDSCAPE ARCHITECT
14#7 (T) 16#7 (T) 8#7 (T) 8#7 (T) 14#7 (T) 14#7 (T)
WALL
SWA Group
TYP. U.N.O.
LEVEL 3 TO 4 #4@12" #4@12" 14#7 (T) 16#7 (T) #4@12" #4@12" 8#7 (T) 8#7 (T) #4@12" #4@12" 14#8 (T) 14#8 (T) Dallas, TX 75207
LEVEL 06 LEVEL 06 LEVEL 06 (214-954-0016 Chuck McDaniel)
531'-2" 531'-2" 531'-2" LEVEL 2 TO 3 #4@12" #4@12" #4@12" #4@12" #4@12" #4@12"
14#8 (T) 16#8 (T) 8#8 (T) 8#8 (T) 14#8 (T) 14#8 (T)
STRUCTURAL
SEE 1/S502-OF FOR
BOUNDARY ELEMENT, TYP. Datum Engineers
ADD'L REINF. AT WALL LEVEL 1 TO 2 #4@12" #4@12" #4@12" #4@12" #4@12" #4@12" 6516 Forest Park Road
OPENING, TYP. 14#8 (T) 16#8 (T) 8#8 (T) 8#8 (T) 14#9 (T) 14#9 (T)
Dallas, TX 75235
LEVEL B1 TO (214-358-0174 Rodolfo D'Arlach)
#4@12" #4@12" 14#9 (T) 16#9 (T) #4@12" #4@12" 8#9 (T) 8#9 (T) #5@12" #5@12" 14#10 (T) 14#10 (T)
LEVEL 05 LEVEL 05 LEVEL 05 LEVEL 1
521'-2" 521'-2" 521'-2" MEP ENGINEER
LEVEL B2 TO ME Engineers, Inc.
#4@12" #4@12" 14#9 (T) 16#9 (T) #4@12" #4@12" 8#9 (T) 8#9 (T)
LEVEL B1
12" WALL
Dallas, TX 75207
LEVEL B3 TO (214-741-1589 Drew Shivley)
#5@12" #5@12" 14#9 (T) 16#9 (T) #5@12" #5@12" 8#9 (T) 8#9 (T)
LEVEL B2
ELEVATOR CONSULTANT
LEVEL 04 LEVEL 04 LEVEL 04 DOWELS #5@12" 14#9 (T) 16#9 (T) #5@12" 8#9 (T) 8#9 (T) #5@12" 14#10 (T) 14#10 (T) Persohn | Hahn Associates, Inc.
511'-2" 511'-2" 511'-2" 8612 Broad Meadow Lane
McKinney, TX 75071
SW-2
SW-1
DETAIL 9/S502-OF 7/S502-OF 8/S502-OF 6/S502-OF 11/S503-OF 12/S503-OF

NOTES INTERIOR DESIGNER

Rottet Studio
LEVEL 03 LEVEL 03 LEVEL 03 808 Travis Street, Suite 100
501'-2" 501'-2" 501'-2" Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
3'-0"
2'-0" 2'-0" 16 17
S502-OF
3'-0"
S502-OF SHEAR WALL LINK BEAM SCHEDULE
3'-0"
LEVEL 02 LEVEL 02 LEVEL 02 SW-1 www.datumengineers.com | Co. Reg. No. F-2819
491'-2" 491'-2" 491'-2" Dallas Austin San Antonio
12" WALL
214-358-0174 512-469-9490 210-858-2880

STIRRUPS Datum Project No. 19166
TOP & BOT. NO. INTERM.
TENSION LAP SPLICE
TENSION LAP SPLICE

SCHEDULE (T) PER
LEVEL REINF. LEGS BARS DETAIL DATE ISSUE TITLE

SCHEDULE (T) PER TENSION LAP SPLICE
SCHEDULE (T) PER
A/S401-OF TYP.
SIZE SPACING @ END 04/03/2020 SCHEMATIC DESIGN PRESENTATION

A/S401-OF TYP.
A/S401-OF TYP. 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
LEVEL 01 LEVEL 01 LEVEL 01 LEVEL B2 2#9 #4 1@2, R@8 2 2#9 10/S503-OF

481'-2" 481'-2" 481'-2" 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT

LEVEL B3 2#9 #4 1@2, R@8 2 2#9 10/S503-OF 12/18/2020 90% CONSTRUCTION DOCUMENTS
18" WALL
3'-0"
12 01/25/2021 100% CONSTRUCTION DOCUMENTS
S502-OF
3'-4 1/2" 2'-4" 11 13
3'-0"
2'-3"
S502-OF S502-OF
1/S502-OF, TYP. LEVEL B1 LEVEL B1 LEVEL B1 RESERVED FOR REVIEWERS NOTES
AT OPENINGS 471'-0" 471'-0" 471'-0"
TENSION LAP SPLICE
1/S502-OF 1'-6"
SCHEDULE (T) PER
TENSION LAP SPLICE

SCHEDULE (T) PER
A/S401-OF TYP.
12
2'-6"
A/S401-OF TYP.
1'-8"
14
7'-2"
S502-OF
S502-OF
1'-6" 1'-6"
LEVEL B2 LEVEL B2 LEVEL B2
461'-8" 461'-8" 461'-8"
2'-4" RETENTION 14#9 PIER DOWELS
3'-4 1/2" 1/S502-OF
14" WALL
SYSTEM AT INTERIOR PIER

7'-2"
LEVEL B3 LEVEL B3 LEVEL B3

.
452'-4" 452'-4" 452'-4" REV. DATE ISSUE TITLE

NOTE:
.
NOTE: SEE 1/S501-OF FOR

14#9 PIER DOWELS
SEE 1/S501-OF FOR INFO. NOT SHOWN.
AT INTERIOR PIER
INFO. NOT SHOWN.
SEE PLAN FOR SHEAR WALL DIMENSIONS SEE PLAN FOR SHEAR WALL DIMENSIONS SEE PLAN FOR SHEAR WALL DIMENSIONS
1 SW-1 ELEVATION 2 SW-2 ELEVATION 3 SW-3 ELEVATION

1/8" = 1'-0" 1/8" = 1'-0" 1/8" = 1'-0"
MAPLE TERRACE
3001 MAPLE AVENUE
SHEAR WALL ELEVATIONS
190013
PROJECT NUMBER
NOTE:
2'-0" SEE 3/S502-OF FOR
MIN. INFO. NOT SHOWN.
SEE PLAN
SEE PLAN
EXTEND VERTICAL
BARS FULL STORY SHEAR WALL,
HEIGHT SEE ELEVATION SHEAR WALL,
(S501-OF) FOR REINF. SEE ELEVATION
SEE PLAN DEVELOPER
(S501-OF) FOR REINF.
Hines
#5 x 4'-0" EACH 2200 Ross Avenue, Suite 4200W
FACE, EACH CORNER. RETENTION SYSTEM
SEE PLAN WATERSTOP Dallas, TX 75201
PLACE INSIDE OF SEE SPECS (972-716-2908 Corbin Eckel)
1 1/2" TYPICAL WALL 1'-0"
CLEAR ADDITIONAL #5 x 5'-0" @ 12" TOP
REINFORCING. 5'-0" 2800 Post Oak Blvd., 49th Floor
(TYP. AT SHEAR WALLS (U.N.O.) Houston, TX 77056
#5 @ 12" OPTIONAL C.J. (713-621-8000 Juan Delgado)
SCHED.
DEPTH
PROVIDE EXTRA BARS IN T.O.S.C. EL.
T.O.S.C. EL.
EACH FACE, EQUAL TO SEE PLAN
SEE PLAN EQUITY PARTNERS
AREA OF INTERRUPTED T.O.S.C. EL. McNair Interests
BARS (1#5 EACH FACE SEE PLAN 109 N. Post Oak Lane, Suite 600
EACH SIDE MINIMUM). Houston, TX 77024
2'-0"
(Drew Steffen)

T.O. PIER EL. RETENTION SYSTEM New York, New York 10020
T.O. PIER EL.
TYPICAL WALL SEE PLAN (David Leff)
ELEVATION REINFORCING
TENSION LAP SPLICE

1'-2"
3#8 X CONT. 14" AT SW-2 5G Studio Collaborative, LLC.
PER A/S401-OF
BOT. 1217 Main St., Suite 500
REINFORCEMENT AT CONCRETE WALL OPENING 18" AT SW-3
SHED (T)
1'-0" Dallas, TX 75202
TYPICAL DETAIL (214-347-4982 Christine Robbins-Elrod)
NO SCALE MASTER/MULTIFAMILY ARCHITECT

3/4" = 1'-0" 1 3/4" = 1'-0" 3 3/4" = 1'-0" 4 3/4" = 1'-0" 5 GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
Baldwin Associates
ADDITIONAL #5 x 5'-0" @ 12" TOP
(TYP. AT SHEAR WALLS (U.N.O.) GEOTECH
ECS Southwest, LLP
OPTIONAL C.J. 3033 Kellyway Drive, Suite 110
9" 9" Carrollton, TX 75006
SLAB THK.
SCHED.
CIVIL ENGINEER
9"
STAIR T.O.S.C. EL.
SEE PLAN 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
9"
1'-3"
3'-0"
9"
9"
LANDSCAPE ARCHITECT
C.L. OF PIER SWA Group
9"
9"
9"
SHEAR WALL, Dallas, TX 75207
SEE ELEVATION (214-954-0016 Chuck McDaniel)
(S501-OF) FOR REINF
STRUCTURAL
Datum Engineers
9" 6516 Forest Park Road
1'-6" 1'-6" Dallas, TX 75235
PIER DOWELS TO MATCH WALL REINF. PIER DOWELS TO MATCH WALL REINF. MEP ENGINEER
PIER DOWELS TO MATCH WALL REINF.
PIER DOWELS TO MATCH WALL REINF. ME Engineers, Inc.
SCHED. WALL VERT. REINF. SCHED. WALL VERT. REINF. 1825 Market Center Blvd., Suite 600
SCHED. WALL VERT. REINF.
SCHED. WALL VERT. REINF. Dallas, TX 75207
PLAN PLAN (214-741-1589 Drew Shivley)
PLAN ELEVATOR CONSULTANT

6 7 3/4" = 1'-0" 8 9 10
3/4" = 1'-0" 3/4" = 1'-0" PLAN 3/4" = 1'-0" 3/4" = 1'-0" Persohn | Hahn Associates, Inc.
McKinney, TX 75071
NOTE: INTERIOR DESIGNER

NOTE: NOTE: NOTE: SEE 9/S502-OF FOR
SEE 7/S502-OF FOR SEE 7/S502-OF FOR SEE 8/S502-OF FOR Rottet Studio
INFO. NOT SHOWN. 808 Travis Street, Suite 100
INFO. NOT SHOWN. INFO. NOT SHOWN. INFO. NOT SHOWN.
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
SEE PLAN
(TYP. AT SHEAR WALLS (U.N.O.)

OPTIONAL C.J. SLAB 214-358-0174 512-469-9490 210-858-2880
SEE PLAN Datum Project No. 19166

DATE ISSUE TITLE
T.O.S.C. EL.
SEE PLAN
9"

9"
3'-0"
SHEAR WALL,
SEE ELEVATION RESERVED FOR REVIEWERS NOTES
9" 9" (S501-OF) FOR REINF
PLAN PLAN PLAN

PLAN
3/4" = 1'-0" 11 3/4" = 1'-0" 12 3/4" = 1'-0" 13 3/4" = 1'-0" 14 3/4" = 1'-0" 15
NOTE:
NOTE: SEE 4/S503-OF FOR NOTE:
SEE 16/S502-OF FOR INFO. NOT SHOWN. SEE 4/S503-OF FOR
SEE PLAN INFO. NOT SHIOWN. INFO. NOT SHOWN.
TENSION LAP SPLICE

SEE PLAN
SEE PLAN SEE PLAN SHEAR WALL, SEE PLAN SEE PLAN
PER A/S401 OF
SEE PLAN
SEE ELEVATION
SCHED (T)
SHEAR WALL, (S501-OF) FOR REINF
SLAB
OPTIONAL C.J. #5 X 10'-0" @12" SEE ELEVATION
SEE PLAN
SCHED. DEPTH
SCHED. DEPTH
SCHED. DEPTH
(TYP. AT SHEAR WALLS (U.N.O.) SHEAR WALL,
SEE SCHED.
SLAB ON VOID SEE ELEVATION

SEE PLAN OPTIONAL C.J. (S501-OF) FOR REINF.
ADDITIONAL #5 x 5'-0" ADDITIONAL #5 x 5'-0" @ 12" TOP
@ 12" TOP (TYP. AT (TYP. AT SHEAR WALLS (U.N.O.)
T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL. T.O.S.C. EL. SHEAR WALLS (U.N.O.)
T.O.S.C. EL.
SEE PLAN
SCHED.
DEPTH
SCHED DEPTH
SCHED DEPTH
BEAM BEAM
SEE PLAN SEE PLAN
SHEAR WALL,
SEE ELEVATION SCHED. WIDTH SCHED. WIDTH
(S501-OF) FOR REINF
SHEAR WALL, MAPLE TERRACE

SEE ELEVATION SHEAR WALL, 3001 MAPLE AVENUE
(S501-OF) FOR REINF SEE ELEVATION SHEAR WALL, DALLAS, TEXAS, 75201
(S501-OF) FOR REINF SEE ELEVATION
(S501-OF) FOR REINF SHEAR WALL SECTIONS AND
RETENTION SYSTEM
SEE PLAN
RETENTION SYSTEM DETAILS
SEE PLAN
16 17 18 19 20
3/4" = 1'-0" 3/4" = 1'-0" 3/4" = 1'-0" 3/4" = 1'-0" 3/4" = 1'-0"
190013
PROJECT NUMBER
NOTE: NOTE:
NOTE: NOTE: SEE 4/S503-OF FOR SEE 4/S503-OF FOR
SCHED. DEPTH
SEE 4/S503-OF FOR SEE 4/S503-OF FOR INFO. NOT SHOWN. INFO. NOT SHOWN.
SEE PLAN
TENSION LAP SPLICE

INFO. NOT SHOWN. INFO. NOT SHOWN. SEE PLAN SEE
SEE PLAN
PER A/S401 OF
PLAN
SCHED (T)
SEE PLAN HOOK BARS
SHEAR WALL,
ROOFING
SEE ELEVATION COLUMN BEYOND
SHEAR WALL, SEE ARCH'L T.O.S.C. EL.
(S501-OF) FOR REINF SEE PLAN
SEE PLAN
SCHED.
SLAB
DEPTH
SEE ELEVATION
(S501-OF) FOR SEE PLAN ROOF SLAB DEVELOPER
REINF SLAB SEE PLAN Hines
SEE PLAN ADDITIONAL #5 x 5'-0" @ 12" TOP 2200 Ross Avenue, Suite 4200W
(TYP. AT SHEAR WALLS (U.N.O.) Dallas, TX 75201
SCHED. DEPTH
T.O.S.C. EL. (972-716-2908 Corbin Eckel)
SEE PLAN
T.O.S.C. EL. 2800 Post Oak Blvd., 49th Floor
SEE PLAN T.O.S.C. EL. Houston, TX 77056
SCHED. DEPTH
SEE PLAN
SCHED.
SCHED. DEPTH
PLAN
DEPTH
SEE
SCHED. DEPTH
BEAM
SEE PLAN
SCHED. DEPTH
EQUITY PARTNERS
SCHED. DEPTH
McNair Interests
Houston, TX 77024
SCHED. DEPTH
(Drew Steffen)
BEAM Mitsui Fudosan America
BEAM SEE PLAN 1251 Avenue of the Americas, Suite 800
SCHED. WIDTH SCHED. WIDTH
SEE PLAN New York, New York 10020
SHEAR WALL, SHEAR WALL, BEAM (David Leff)
SEE ELEVATION SEE ELEVATION SEE PLAN
(S501-OF) FOR REINF (S501-OF) FOR REINF. OFFICE/RETAIL ARCHITECT
BEAM
SEE PLAN 1217 Main St., Suite 500
Dallas, TX 75202
SHEAR WALL, (214-347-4982 Christine Robbins-Elrod)
SEE ELEVATION SCHED. WIDTH
SEE PLAN
3/4" = 1'-0" 1 (S501-OF) FOR REINF
3 4 SCHED. WIDTH
3/4" = 1'-0" 2 3/4" = 1'-0" 3/4" = 1'-0" 3/4" = 1'-0" 5 GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
NOTE: SEE PLAN Baldwin Associates
SEE 20/S502-OF FOR 3904 Elm Street, Suite B
SHEAR WALL Dallas, TX 75226
INFO. NOT SHOWN.
SHEAR WALL, BEYOND (214-824-7949 Robert Baldwin)
SHEAR WALL, SEE ELEVATION SEE S501-OF
SEE PLAN SEE PLAN #5X5'-0"@12" (S501-OF) FOR REINF GEOTECH
SEE ELEVATION
(S501-OF) FOR REINF. ECS Southwest, LLP
#5X10'-0" @ 12" 3033 Kellyway Drive, Suite 110
SEE SCHED.
STRUCTURAL SLAB SLAB ON VOID SLAB ON VOID Carrollton, TX 75006
#5 ADDN'L TOP X 16'-0'' @ 12'' SLAB (972-392-3222 Siddharth Neekhra)
HOOK BARS SEE PLAN SEE PLAN SEE PLAN CENTER ON THE LINK BEAM SEE PLAN
SCHED. DEPTH
SHEAR WALL, CIVIL ENGINEER

SEE ELEVATION T.O.S.C. EL. T.O.S.C. EL. Kimley-Horn and Associates, Inc.
(S501-OF) FOR SEE PLAN SEE PLAN 13455 Noel Road, Two Galleria Office Tower, Suite 700
SEE PLAN SEE PLAN
REINF. Dallas, TX 75240
LANDSCAPE ARCHITECT
SWA Group
REINF. FROM BEAM LINK BEAM, SEE 2001 Irving Boulevard, Suite 157
BEYOND, SEE SCHED. FOR BEAM Dallas, TX 75207
MECHANICAL STAIR SHAFT REINF. (214-954-0016 Chuck McDaniel)
SHAFT 14/S307-OF
TOP OF WALL OPENING
SEE SHEAR WALL EL STRUCTURAL
Datum Engineers
BOTTOM OF
BEAM BEYOND SHEAR WALL, Dallas, TX 75235
SEE ELEVATION (214-358-0174 Rodolfo D'Arlach)
(S501-OF) FOR REINF. SHEAR WALL
BEYOND MEP ENGINEER
RETENTION SYSTEM RETENTION SYSTEM SEE S501-OF ME Engineers, Inc.
SHEAR WALL,
SEE PLAN SEE ELEVATION SEE PLAN SEE 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
(S501-OF) FOR REINF. ELEVATION (214-741-1589 Drew Shivley)
ELEVATOR CONSULTANT
3/4" = 1'-0" 6 3/4" = 1'-0" 7 3/4" = 1'-0" 8 3/4" = 1'-0" 9 3/4" = 1'-0" 10 Persohn | Hahn Associates, Inc.
McKinney, TX 75071
INTERIOR DESIGNER
Rottet Studio
3" 6" NOTE: 808 Travis Street, Suite 100
SEE 20/S502-OF FOR Houston, TX 77002
INFO. NOT SHOWN. (713-221-1830 x 6105 Anja Majkic)
3" 6"
SEE PLAN

1'-6"
214-358-0174 512-469-9490 210-858-2880
SHEAR WALL, Datum Project No. 19166

C.L. OF PIER SEE ELEVATION DATE ISSUE TITLE
2'-0"

2'-0"

C.L. OF PIER 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
T.O.S.C. EL.
9"

SEE PLAN
3"

9"
SCHED.
DEPTH

PLAN
3/4" = 1'-0" 11 PLAN 3/4" = 1'-0" 12 3/4" = 1'-0" 13
6"
6"
3'-0"
3'-0"
9"
MAPLE TERRACE
3001 MAPLE AVENUE
SHEAR WALL SECTIONS AND
PLAN DETAILS
16 PLAN 17
3/4" = 1'-0" 3/4" = 1'-0"
190013
PROJECT NUMBER
E-1.4 E-1.3 E-1.2 E-1.1 E-1.8 E-1.7
NOTE:
ALL STEEL TO BE E-C E-2 3'-7" 3'-4" W.B., SEE PLAN
AND ELEVATION
FIREPROOFED FOR
1 HOUR RATING
EXTEND CHANNEL TO EXISTING COLUMN
6 EXISTING LOUVER
1" SHORT OF COLUMN SEE PLAN
EXISTING LOUVER EACH END. FIELD S601-OF OPENING
OPENING TO BE EXISTING COLUMN EXISTING LOUVER VERIFY PRIOR TO SIM.
1 6 LEVEL 01
INFILLED, SEE PLAN OPENING TO BE INFILLED FABRICATION DEVELOPER
SEE 3/S613-OF , TYP. S601-OF 481'-2"
2'-8"
SEE 3/S613-OF , TYP.
2'-3"
Hines
LEVEL 01 LEVEL 01 2200 Ross Avenue, Suite 4200W
Dallas, TX 75201
481'-2" 481'-2" 6" MIN. 6" MIN. (972-716-2908 Corbin Eckel)
2'-8"
3'-0" 3'-0"
Houston, TX 77056
7'-2"
EQUITY PARTNERS
EXISTING NEW OPENING BUILT UP RAMP
BASEMENT WALL IN EXISTING McNair Interests
SEE PLAN 109 N. Post Oak Lane, Suite 600
SEE PLAN BASEMENT WALL Houston, TX 77024
.016 (Drew Steffen)
LEVEL B1
4'-11 1/2" 2'-7" 3'-4" Mitsui Fudosan America
471'-0"
1'-3"
LEVEL B1 LEVEL B1 New York, New York 10020
(David Leff)
471'-0" 471'-0"
1 OFFICE/RETAIL ARCHITECT
NOTE: 1217 Main St., Suite 500
SCAN AND LOCATE EXIST REINF. Dallas, TX 75202
SEE NOTE 7 AND 8 ON FIELD DRILLED NOTE: (214-347-4982 Christine Robbins-Elrod)
ANCHOR NOTES ON S102-OF SCAN AND LOCATE EXIST REINF. NOTE TO CONTRACTOR:
SEE NOTE 7 AND 8 ON FIELD DRILLED MASTER/MULTIFAMILY ARCHITECT
ANCHOR NOTES ON S102-OF FIELD VERIFY ALL EXISTING DIMENSIONS & ELEVATIONS
1/4" = 1'-0" 3 1/4" = 1'-0" 4 PRIOR TO FABRICATION OF MATERIALS AND CONSTRUCTION 1/4" = 1'-0" 5 GFF Architects
Dallas, TX 75201
NOTE: NOTE: ZONING/ENTITLEMENT

NOTES: SEE CONCRETE FOOTING SCAN AND LOCATE EXIST
1. SCAN AND LOCATE EXIST REINF. NOTE: Baldwin Associates
GENERAL NOTES. REINF. SEE NOTE 7 AND 8 ON 3904 Elm Street, Suite B
SEE NOTE 7 AND 8 ON FIELD WHERE EXISTING BEAM/JOIST DEPTH VARY, INSTALL NEW STEEL BEAM BELOW DEEPEST BEAM, FIELD DRILLED ANCHOR CAP PL.3/8" Dallas, TX 75226
DRILLED ANCHOR NOTES ON AND SHIM SHALLOWER MEMBERS PER DETAIL "B". NOTES ON S102-OF. DO NOT (214-824-7949 Robert Baldwin)
S102-OF. DO NOT DAMAGE DAMAGE EXISTING REINF.
EXISTING REINF.
2. ALL STEEL TO BE FIREPROOFED
GEOTECH
EXIST. STRUCTURE BENT PL.3/8X5X AS REQ'D.
FOR 1 HOUR RATING ECS Southwest, LLP
NOTE: X 8" W/2-1/2" DIA. EXP. BOLT 3033 Kellyway Drive, Suite 110
HSS6X6X3/8 W/4" EMBED.
5/S613-OF INSTALL CHANNELS PRIOR TO Carrollton, TX 75006
E.J. SLAB SIM. EXISTING BASEMENT SAWCUTTING OPENINGS. (972-392-3222 Siddharth Neekhra)
SEE PLAN SEE PLAN BASE PL.3/4X12X1'-0" EXSIT. BEAM OR JOIST WALL, SEE PLAN
W/4-3/4" DIA. ANCHOR BOLTS EXIST. T.O.S.C. EL.
CIVIL ENGINEER
#3 DWL. X 2'-0" W/0'-8" EMBEDMENT 6" MIN.
TYP., SEE 13455 Noel Road, Two Galleria Office Tower, Suite 700
T.O.S.C. EL. 19/S613-OF Dallas, TX 75240
4" +/-
SEE PLAN (972-770-1300 Alex Rathbun)
EXIST. T.O.S.C. EL.
SEE PLAN
LANDSCAPE ARCHITECT
8"
SEE ELEVATION
SWA Group
C12X20.7 EA. SIDE 2001 Irving Boulevard, Suite 157
W/ 3/4" DIA. THRU Dallas, TX 75207
EXISTING BASEMENT WALL EDGE OF SAWCUT
MIN.
CAP PL.3/8"
1'-0"
BOLTS @ 12" SHIM TIGHT & HAND PACK CHANNEL, SEE ELVATION (214-954-0016 Chuck McDaniel)
SEE PLAN
INSTALL PRIOR TO W/+/-1" N.S. GROUT, TYP. HSS5X5X1/4 DRILL & EPOXY 3/4" DIA. X 6" 1 1/2" +/- SEE ELEVATION
CUTTING NEW BEARING STRATUM HAS-V-36 @ 12" +/- MAX TYP. AND ARCH'L STRUCTURAL
OPENING W/ HILTI-HIT-RE 500V3 Datum Engineers
6" +/-
COVER
3" CLR.
INSTALL PRIOR TO 3 SIDES, TYP.

CUTTING NEW OPENING BASE PL.1/2" 1/4 Dallas, TX 75235
FOOTING REINF. NEW BEAM 3/16 W/ (2)-1/2" DIA. X 4 1/2" (214-358-0174 Rodolfo D'Arlach)
1" TYP. 1'-6" @ 4#5 E.W. SEE PLAN EXP. BOLT
1/4 3-12 ENDS 3'-6"X3'-6" BEAM
1/4 SEE PLAN PL.3/8X4X0'-8 MEP ENGINEER
1'-0" (F.V.) ME Engineers, Inc.
1/4 1825 Market Center Blvd., Suite 600
PL.1/2" X CONT. Dallas, TX 75207
WELD AFTER (214-741-1589 Drew Shivley)
OPENING IS CUT A B PLAN 3/16
1" MAX.
COLUMN
NOTE: Persohn | Hahn Associates, Inc.
SEE 1/S613-OF FOR CUTTING NEW 8612 Broad Meadow Lane
McKinney, TX 75071
OPENING. DO NOT OVERCUT
3/4" = 1'-0" 6 3/4" = 1'-0" 7 1" = 1'-0" 8 3/4" = 1'-0" 9 1" = 1'-0" 10 INTERIOR DESIGNER
Rottet Studio
Houston, TX 77002
PLATE THK. NOTE: (713-221-1830 x 6105 Anja Majkic)
NOTE: 5" NOTE:
SCAN AND LOCATE EXIST POSSIBLE EDGE NOTES: SCAN AND LOCATE EXIST NOTE: NOTE:
1/2" SEE 1/S613-OF FOR CUTTING NEW
REINF. SEE NOTE 7 AND 8 ON MIN PL.3/4X1'-4"XAS REQ'D OF CONCRETE REINF. SEE NOTE 7 AND 8 ON SEE 1/S613-OF FOR CUTTING NEW SCAN AND LOCATE EXIST
MAX OPENING. DO NOT OVERCUT
FIELD DRILLED ANCHOR 1. SEE FIELD DRILLED EXPANSION BOLT FIELD DRILLED ANCHOR OPENING. DO NOT OVERCUT REINF. SEE NOTE 7 AND 8 ON
NOTES ON S102-OF. DO NOT NOTES FOR INSTALLATION PROCEDURE NOTES ON S102-OF. DO NOT FIELD DRILLED ANCHOR
SEE TABLE FOR 3" MIN.
DAMAGE EXISTING REINF. SIDES 1'-0" +/- 10" +/- TO MISS EXISTING REINFORCING STEEL. DAMAGE EXISTING REINF. NOTES ON S102-OF. DO NOT
TYP. DAMAGE EXISTING REINF.
SEE ELEVATION
3" LENGTH OF RETURN 2. FABRICATE PLATE WITH 3" EDGE Dallas Austin
214-358-0174 512-469-9490
San Antonio
210-858-2880
WELD AT THE TOP DIMENSION FOR TOLERANCE TO ALLOW
3" + / -
SECT. "A" Datum Project No. 19166

EXIST. T.O.S.C. EL. IS EQUAL TO 2 BOLTS TO BE RELOCATED TO MISS EXIST. SLAB
SEE PLAN TIMES THE WELD REINFORCING STEEL AND STILL SEE PLAN DATE ISSUE TITLE
SIZE. MAINTAIN MINIMUM 1 1/2" EDGE T.O.S.C. EL.
DISTANCE. SEE PLAN
3 SIDES
SEE ELEVATION
6" +/-
1/4 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
8" + / -

5" +/-
EXISTING BASEMENT WALL

8" + / -

NOTE: .016
6" +/-
SEE PLAN
SCAN AND LOCATE EXIST REINF.
C10X15.3 EA. SIDE
1" MIN
SEE NOTE 7 AND 8 ON FIELD DRILLED 1'-6" @

ANCHOR NOTES ON S102-OF W/ 3/4" DIA. THRU BOLTS
2-L3X4X5/16 MIN. 1/4 3-12 ENDS RESERVED FOR REVIEWERS NOTES
@ 12" INSTALL PRIOR TO
CUTTING NEW OPENING
L3X3X1/4X0'-3" EA. SIDE 3 SIDES
1/4 1" TYP. PL.1/2" X CONT. CHANNEL, SEE ELVATION
W/1/2" DIA. EXP. BOLT ERECTION SEAT, DRILL & EPOXY 3/4" DIA. X 6"
W/4" EMBEDMENT INCREASE PL. HEIGHT CONNECTION LOAD CAPACITY WELD AFTER
OPENING IS CUT HAS-V-36 @ 12" +/- MAX
AS REQ'D. 1'-4" W/ HILTI-HIT-RE 500V3 1'-0" (F.V.)
EXPANSION BOLTS ANGLE INSTALL PRIOR TO EDGE OF SAWCUT
(SEE TABLE) FACE OF EXISTING STRUCT. WIDE FLANGE SIZE LENGTH 1/4" WELD EXP. BOLTS
SECT. "A" EXISTING BASEMENT WALL CUTTING NEW OPENING
W12 8.5" 18K 6-3/4 DIA. SEE PLAN
DOUBLE ANGLE CONNECTION
1" = 1'-0" 11 TO EXISTING CONCRETE WALL 1" = 1'-0" 13 3/4" = 1'-0" 14 3/4" = 1'-0" 15
NO SCALE
1 02/09/2021 ADDENDUM 1
NOTE:
.016 05/03/2021 ADDENDUM 08
SEE NOTE 7 AND 8 ON FIELD DRILLED
E-A E-B E-B.5 E-C ANCHOR NOTES ON S102-OF
E-4 E-2
EXISTING COLUMN EXISTING COLUMN
E-2 E-B.5 E-B
NEW LOUVER OPENING
IN EXISTING BASEMENT 11'-0" (F.V.) 10'-10" (F.V.)
14 WALL, SEE MECHANICAL 1'-6" (F.V.)
14 C10X15.3 15
15 15
S601-OF EXISTING CONCRETE EXISTING CONCRETE C12X27.5
1'-6 1/2"
S601-OF S601-OF
S601-OF
3'-0"
BASEMENT WALL, C12X20.7 6" +/- S601-OF BASEMENT WALL,
2'-0"
2'-0"
6" +/- 6" +/- 6" +/- 6" +/-

SEE PLAN SEE PLAN
LEVEL 01 LEVEL 01 LEVEL 01
6" +/- 6" +/- 481'-2" 481'-2" 481'-2"
2'-0"
2'-1"
.016
9
6" +/-
C10X15.3 2'-0"
6" +/-
9
6" +/-
6" +/-
6" +/-
4'-0 5/8" S601-OF
2'-0"
5'-10 1/2" S601-OF 6'-11" +/- (F.V.) 2'-10 1/2" 6" +/- 6" +/- 6" +/-
SIM.
6'-0 1/4" +/- (F.V.)
6'-0 1/4" +/- (F.V.)
6'-0 1/4" +/- (F.V.)

+/- (F.V.)
SIM. 1/4
6'-0 1/4" +/- (F.V.)
+/- (F.V.) 9 1/4

C10X15.3 1'-8 3/4" 4'-4"
6'-2 3/4"
1 2'-0"
7'-8 1/2" +/- (F.V.)
9
7'-7" S601-OF C12X20.7
C12X27.5
S601-OF
NEW OPENING IN 1'-0" 1'-4"
1'-0" 2'-10 1/4" 1'-0" .016
NEW WALL 3'-8" 3'-4 1/4" 1'-5"
EXISTING BASEMENT
OPENING 6'-6" 3'-4 1/4"
CONCRETE WALL
FOR MECHANICAL
6" +/-
6" +/-
6" +/-
2'-10 1/2" 2'-10 1/2"

+/- (F.V.) +/- (F.V.)
C10X15.3 EA. SIDE LEVEL B1 LEVEL B1
471'-0" 471'-0" MAPLE TERRACE
W/ 3/4" DIA. THRU
BOLTS @ 12" EXISTING WINDOWS NEW LOUVER OPENING 3001 MAPLE AVENUE
NOTE: EXISTING DOOR TO BE IN EXISTING BASEMENT DALLAS, TEXAS, 75201
TO BE INFILLED C12X20.7 INFILLED. SEE ARCH'L
SCAN AND LOCATE EXIST REINF. EXISTING DOOR OPENING EXISTING WINDOWS WALL, SEE MECHANICAL
SEE NOTE 7 AND 8 ON FIELD DRILLED TO BE INFILLED, SEE 3/S613-OF
SEE ARCH'L AND 3/S613-OF AND 3/S613-OF NOTE: TO BE INFILLED
EXISTING BASEMENT DETAILS
ANCHOR NOTES ON S102-OF SCAN AND LOCATE EXIST REINF. SEE ARCH'L AND 3/S613-OF
17 18 ANCHOR NOTES ON S102-OF
20
1/4" = 1'-0" 1/4" = 1'-0" 1/4" = 1'-0"
190013
PROJECT NUMBER
NOTE:
SHORING SHALL BE DESIGNED BY A
REGISTERED ENGINEER IN THE STATE
RECOMMENDED SEQUENCE NOTES: B OF TEXAS. PROVIDE SEALED
NOTE:
CALCULATIONS AND SHOPS. NOTE:
SEE NOTE 7 AND 8 ON FIELD DRILLED SEE 13/S610-OF FOR
FIELD VERIFY ALL EXISTING FRAMING PRIOR TO HSS8X6X1/2 (LLV) HSS8X6X1/2 (LLV)
FABRICATION AND START OF THIS WORK. E-4 ANCHOR NOTES ON S102-OF INFO. NOT SHOWN.
11
1. TEMPORARY LATERALLY BRACE EXISTING MINIMUM 5" DIA. STD.
12 13/S610-OF S610-OF PIPE OR EQUAL
HSS12X6X3/8 (LLH)
COLUMN AT GRID E-D AND E-0.6. SEE 11/S610-OF.
HSS12X6X3/8 (LLH)
TYP. DEVELOPER
EXIST. 12X20 BEAM

S610-OF EXIST. 18"X18"
5/S610A-OF COLUMN (F.V.) Hines
2. CAREFULLY DEMO EXISTING LEVEL 2 FRAMING. MIN. 4- 1/2 DIA. X 6" EPOXIED
SEE PLAN 2200 Ross Avenue, Suite 4200W
E
TAKE CARE NOT TO DAMAGE EXISTING BEAMS TO ANCHOR CENTERED IN COLUMN.
N. ID
9 6/S610A-OF Dallas, TX 75201
M S
REMAIN. AT APPROX. +/-8" GA. SCAN (972-716-2908 Corbin Eckel)
LU ACH
S610A-OF EXISTING REINF. AND CREATE
2 1/2" (F.V.)
CO k E
3. INSTALL NEW W8 COLUMN, HSS GIRTS AND BOLTING TEMPLATE PRIOR TO 1/4 2800 Post Oak Blvd., 49th Floor
OF =10
BEAMS PER DETAILS 6, 7, 8, 11, 12, 13, AND 8 8 FABRICATION. DO NOT DAMAGE Houston, TX 77056
P
S610A-OF EXIST. COLUMN REINF. (713-621-8000 Juan Delgado)
16/S610-OF AND 5, 6, 7, 9, 12 AND 13/SS610A-OF. S610A-OF
O.H. L4X4X1/2 X 1'-0"
4. REMOVE COLUMN BRACING. EXIST. T.O.S.C. EL. EQUITY PARTNERS
E-7 .016
8 1/2"
EXIST. 10X18 BEAM EXIST. 10X18 BEAM
(F.V.)
HSS12X6X3/8 (LLH)
HSS12X6X3/8 (LLH)
Houston, TX 77024
1'-0" MAX.
(Drew Steffen)
12
11 EXIST. JOIST
S610A-OF Mitsui Fudosan America
NOTE: S610-OF (FIELD VERIFY) 1251 Avenue of the Americas, Suite 800
SCAN AND LOCATE EXIST REINF. C New York, New York 10020
SEE NOTE 7 AND 8 ON FIELD DRILLED (David Leff)
ANCHOR NOTES ON S102-OF HSS12X6X3/8 (LLH) HSS12X6X3/8 (LLH)
HSS 6" OFFICE/RETAIL ARCHITECT
E-D SEE PLAN
1/4
O.H. 1217 Main St., Suite 500
11 Dallas, TX 75202
TEMP. BRACE 10 (214-347-4982 Christine Robbins-Elrod)
10 S610-OF S610A-OF
S610A-OF SIM. EXISTING COLUMN
NOTE TO CONTRACTOR: SEE PLAN MASTER/MULTIFAMILY ARCHITECT
GFF Architects
FIELD VERIFY ALL EXISTING DIMENSIONS 2808 Fairmount St., Suite 300
Dallas, TX 75201
& ELEVATIONS PRIOR TO FABRICATION E-0 E-0.4 E-0.6 E1 1 (214-303-1500 Michael Reyes)
OF MATERIALS AND CONSTRUCTION ZONING/ENTITLEMENT

Baldwin Associates
LEVEL 02 - GYM FLOOR OPENING 3 1" = 1'-0" 5 3904 Elm Street, Suite B
2 SCALE 1/8" = 1'-0"
3/4" = 1'-0" Dallas, TX 75226
GEOTECH
NOTE: ECS Southwest, LLP
NOTE: SEE 8/S610-OF FOR 3033 Kellyway Drive, Suite 110
SCAN AND LOCATE EXIST REINF. HSS BEAM EXIST. BEAM Carrollton, TX 75006
INFO. NOT SHOWN. TO REMAIN
SEE NOTE 7 AND 8 ON FIELD DRILLED SEE PLAN (972-392-3222 Siddharth Neekhra)
ANCHOR NOTES ON S102-OF SEE PLAN
TYP. CIVIL ENGINEER
PL.3/4X18 X AS SHOWN 9 1/4 3
EXIST. COLUMN EXISTING PERIMETER
W/ DRILL AND EPOXY 5- Kimley-Horn and Associates, Inc.
COLUMN BEYOND S610A-OF SEE PLAN BEAM, SEE PLAN 13455 Noel Road, Two Galleria Office Tower, Suite 700
3/4" DIA. X 8" HAS-V-36 W/ EXIST. BEAM 6" +/- Dallas, TX 75240
7
HILTI-HIT-RE 500V3 EXISTING COLUMN EXIST. BEAM AND JOIST TO REMAIN 1" MAX. (972-770-1300 Alex Rathbun)
S610A-OF SEE PLAN SEE PLAN
CHIP OUT EXISTING 6/S610A-OF SEE PLAN TYP.
EXISTING DOWNTURNED SLAB
13/S610A-OF LANDSCAPE ARCHITECT
HSS BEAM STRUCTURE
SEE PLAN TO ALLOW BEAM SWA Group
EXIST. SLAB & JOISTS 2001 Irving Boulevard, Suite 157
2 1/2"
(F.V.)
CONNECTION
1" GAP
TO BE REMOVED Dallas, TX 75207

LEVEL 2
LEVEL 2 EXISTING COLUMN
SEE PLAN STRUCTURAL
SEE PLAN SEE PLAN
6" +/- 6" +/- 6" +/-

Datum Engineers
1'-6" (F.V.)
4" +/-
L4X4X1/2 X 0'-4" Dallas, TX 75235
EXISTING PERIMETER
4" +/-
6" +/-
STL. EL. HSS BEAM (214-358-0174 Rodolfo D'Arlach)

BEAM, SEE PLAN
= 109'-6" SEE PLAN L4X4X1/2 X 12"
W/2-3/4" DIA X 8" MEP ENGINEER
HSS BEAM
EXISTING SEE PLAN HAS-V-36 W/ ME Engineers, Inc.
HSS BEAM TYP. HILTI-HIT-RE 500V3, 1825 Market Center Blvd., Suite 600
PERIMETER
4" +/-
6" +/- 10" 1/4 Dallas, TX 75207
MIN.
SEE PLAN EACH SIDE
BEAM, SEE PLAN
3"
3 1/2" +/- (214-741-1589 Drew Shivley)
9" +/- TYP. EXISTING PERIMETER
L6X6X1/2 COPED AROUND BEAM
W/3- 3/4" DIA. X 8" HAS-V-36 W/ BEAM, SEE PLAN ELEVATOR CONSULTANT
2'-6"
1/4 6 HILTI-HIT-RE 500V3 Persohn | Hahn Associates, Inc.
SCAN EXISTING REINF. AND 8612 Broad Meadow Lane
NOTE: PLAN McKinney, TX 75071
CREATE BOLTING TEMPLATE
SCAN AND LOCATE EXIST REINF. (972-832-4232 Tom Williams)
PRIOR TO FABRICATION. DO NOT
DAMAGE EXIST. COLUMN REINF.
ANCHOR NOTES ON S102-OF INTERIOR DESIGNER
1" = 1'-0" 6 3/4" = 1'-0" 7 3/4" = 1'-0" 8 3/4" = 1'-0" 9 3/4" = 1'-0" 10 Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
NOTE: NOTE:
SEE 11/S610-OF FOR SCAN AND LOCATE EXIST REINF. 3 1/2" +/- NOTE:
INFO. NOT SHOWN. EXIST. COLUMN EXIST. COLUMN
SEE NOTE 7 AND 8 ON FIELD DRILLED NOTE: SEE 14/S610A-OF FOR
ANCHOR NOTES ON S102-OF SEE PLAN INFO. NOT SHOWN.
SEE 20/S610A-OF FOR
3" MIN.
HANDRAIL INFO. NOT SHOWN.
SECT
SEE ARCH'L COLUMN www.datumengineers.com | Co. Reg. No. F-2819
A
SEE PLAN Dallas Austin San Antonio
COPE HSS BEAM 1" MAX. 214-358-0174 512-469-9490 210-858-2880

BENT PL6X10X5/8 (LLH) EXIST. BEAM EXIST. BEAM EXIST. COLUMN
AROUND EXIST. COL. TYP. 4" TYP. Datum Project No. 19166
DRILL & EPOXY 3/4" DIA. X 6" #4 DRILLED
6" +/- 6" +/- 6" +/-
SEE PLAN SEE PLAN
8" +/-
TYP.
DIM. DATE ISSUE TITLE
E.J. @ 2'-0" O.C. MAX HAS-V-36 HSS BEAM
ADHESIVE DWLS. ROUGHEN SURFACE,
SEE PLAN W/ HILTI-HIT-RE 500V3. SEE PLAN AND 11/S610-OF W/STD. HOOK TYP.
SCAN EXISTING FOR REINF. W/ 6" EMBEDMENT EXIST. FLOOR
PRIOR TO DRILLING. DO NOT CLOSURE PL.3/8" 6" +/- @ 8" +/- VERT. 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
3" +/-
TYP.
EXIST. CONC. FRAMING
DAMAGE EXIST. REINF. SPACING W/ HILTI- COLUMN
SLAB HIT-RE 500V3 . EXIST. SLAB & 10/30/2020 ISSUE FOR PERMIT
6"
SEE PLAN
1"
EXIST. SLAB & JOISTS JOISTS 12/18/2020 90% CONSTRUCTION DOCUMENTS

4" +/-
TO BE REMOVED EXIST. VERTICAL 01/25/2021 100% CONSTRUCTION DOCUMENTS

ROUGHEN EXISTING REINFORCEMENT
6" +/- 6" +/- 6" +/-
LEVEL 2 CONCRETE TO 1/4" TO REMAIN
SEE PLAN AMPLITUDE AND
6" +/- 6" +/- TYP. HSS BEAM RESERVED FOR REVIEWERS NOTES
1/4
SEE PLAN APPLY SIKA STOP COLUMN 2" BELOW
BONDING AGENT BEAM AND PACK WITH 2"
OR EQUAL, TYP. #3 TIES X AS SHOWN
L4X4X1/2 X 0'-4", TYP. OF N.S. GROUT
AT 12"
2"
(5 TOTAL)
3,000 PSI GUNNITE
EXISTING PERIMETER EXIST. COLUMN .016
#5 VERT.
3" MIN.
BEAM, SEE PLAN L6X6X1/2

EXIST. BEAM EXISTING COLUMN (8 TOTAL)
W/6- 3/4" DIA. X 8" HAS-V-36 W/
SEE PLAN HSS BEAM SEE PLAN .016
HILTI-HIT-RE 500V3.
SEE PLAN SCAN EXISTING REINF. AND EXIST. COLUMN
CREATE BOLTING TEMPLATE SECTION "A" NOTE: COLUMN ELEVATION
PRIOR TO FABRICATION. DO NOT SCAN AND LOCATE EXIST REINF.
NOTE: DAMAGE EXIST. COLUMN REINF. SEE NOTE 7 AND 8 ON FIELD
PLAN SCAN AND LOCATE EXIST REINF. DRILLED ANCHOR NOTES ON
SEE NOTE 7 AND 8 ON FIELD DRILLED S102-OF. DO NOT DAMAGE
3/4" = 1'-0" 11 3/4" = 1'-0" 12 ANCHOR NOTES ON S102-OF 3/4" = 1'-0" 13 EXISTING REINF. 3/4" = 1'-0" 14 3/4" = 1'-0" 15 REV. DATE ISSUE TITLE
.016 05/03/2021 ADDENDUM 08
NOTE: NOTE:
SEE 20/S610A-OF FOR NOTE: NOTE: DRILLED ADHESIVE DOWELS
SCAN AND LOCATE EXIST REINF. EXIST. COLUMN
INFO. NOT SHOWN. EXIST. COLUMN SEE 20/S610A-OF FOR SCAN AND LOCATE EXIST REINF. @ 12" OC, EMBED 6" MIN. SEE
SEE NOTE 7 AND 8 ON FIELD
INFO. NOT SHOWN. SEE NOTE 7 AND 8 ON FIELD "DRILLED ADHESIVE DOWEL"
DRILLED ANCHOR NOTES ON
DRILLED ANCHOR NOTES ON GENERAL NOTES
S102-OF. DO NOT DAMAGE
SECT
SECT
S102-OF. DO NOT DAMAGE
EXISTING REINF.
A
A
EXISTING BASEMENT EXISTING REINF.
WALL
8" +/-
TYP.
4" TYP. #7 VERT. ROUGHEN SURFACE, #4 DRILLED ROUGHEN SURFACE,
EXIST. COLUMN 4" TYP. EXIST. COLUMN
#3 X AT 12" (4 TOTAL) TYP. ADHESIVE DWLS. TYP.
DRILL THROUGH EXISTING DIM. W/STD. HOOK DIM.
EXIST. FLOOR FRAMING EXIST. CONC.
COLUMN AND EPOXY WITH EXIST. VERTICAL W/ 6" EMBEDMENT COLUMN SAWCUT, CHIP, REMOVE
HILTI-HIT-RE 500V3 REINFORCEMENT @ 8" +/- VERT.
AND REPLACE EXISTISTING
TO REMAIN SPACING W/ HILTI-
4"
SLAB-ON-GRADE AS REQD
HIT-RE 500V3 .
EXIST. VERTICAL
ROUGHEN EXISTING REINFORCEMENT
CONCRETE TO 1/4" TO REMAIN
AMPLITUDE AND
6" (F.V.)
FIELD VERIFY
.016
2"
APPLY SIKA
1 1/2" +/-
STOP COLUMN 2" BELOW

ROUGHEN EXISTING BONDING AGENT
FIELD VERIFY
BEAM AND PACK WITH 2"
FIELD VERIFY
CONCRETE TO 1/4" OF N.S. GROUT OR EQUAL, TYP. #3 TIES X AS SHOWN
AMPLITUDE AND AT 12"
APPLY SIKA 3" +/- EXIST. CONC. 6" +/- EMBED VERTICAL
BONDING AGENT COLUMN
OR EQUAL, TYP. EXIST. COLUMN 3,000 PSI GUNNITE TYP. BARS 6" MIN MAPLE TERRACE
#7 VERT.
#7 VERT. (12 TOTAL)
3001 MAPLE AVENUE
.016 .016 DALLAS, TEXAS, 75201
(6 TOTAL)
3,000 PSI GUNNITE SECTION "A"
#4 DRILLED ADHESIVE EXIST FOOTING BELOW EXIST
SECTION "A"
EXIST FOOTING BELOW EXIST EXISTING FLOOR OPENING
DWLS. W/STD. HOOK SLAB-ON-GRADE, REINF NOT SLAB-ON-GRADE, REINF NOT
W/ 6" EMBEDMENT SHOW FOR CLARITY SHOW FOR CLARITY
@ 8" +/- VERT. SPACING
W/ HILTI-HIT-RE 500V3 COLUMN ELEVATION 3/4" = 1'-0" 17 3/4" = 1'-0" 18 COLUMN ELEVATION 3/4" = 1'-0" 20 190013 S610A-OF
7 8 7 8
11 1 RECOMMENDED SEQUENCE NOTES:
SEE 3/S610A-OF TEMP. BRACE
AT BOTTOM OF S610-OF S220-OF
FIELD VERIFY ALL EXISTING FRAMING PRIOR TO FABRICATION
BRACE, SIM.
AND START OF THIS WORK.
COMPLETE ALL WORK RELATED TO INTERIOR COLUMN
E-A E-A JACKETING PER DETAILS 2, 17, 19, AND 20/S610.
HSS12X6X3/8 LLH, TYP. DEVELOPER
12 1. TEMPORARY LATERALLY BRACE ALL 5 EXISTING Hines
HSS8X6X1/2 (LLV)
HSS8X6X1/2 (LLV)
SEE 3/S610A-OF TEMP. BRACING BY 8/S610-OF S610-OF COLUMNS. SEE 11/S610-OF. 2200 Ross Avenue, Suite 4200W
COLUMN JACKET 8/S610-OF Dallas, TX 75201
AT BOTTOM OF GENERAL CONTRACTOR, SEE 17/S610-OF
COLUMN JACKET 2. SHORE EXISTING L2 FRAMING 5' BEYOND EXTENT OF (972-716-2908 Corbin Eckel)
BRACE, TYP. SEE ELEVATIONS, TYP.
19/S610-OF
FINAL SAWCUTS. SHORING SHALL EXTEND TO
19/S610-OF 2800 Post Oak Blvd., 49th Floor
BASEMENT LEVEL.
Houston, TX 77056
20/S610-OF
20/S610-OF
20/S610-OF
20/S610-OF
3. CAREFULLY DEMO EXISTING LEVEL 2 FRAMING.
E-B E-B EQUITY PARTNERS
4. INSTALL NEW W8 COLUMNS AND HSS GIRTS AND
BEAMS PER DETAILS 6, 7, 8, 11, 12, 13, AND 16/S610-OF. McNair Interests
13/S610-OF COLUMN JACKET 13/S610-OF 109 N. Post Oak Lane, Suite 600
19/S610-OF 19/S610-OF
HSS8X6X1/2 (LLV)
HSS8X6X1/2 (LLV)
SEE 17/S610-OF Houston, TX 77024
PORTION TO BE DEMO'D 5. REMOVE COLUMN BRACING AND SHORING. (Drew Steffen)
SEE NOTE 1 ON 19/S610-OF
6. NEW CANOPY PER 2/S611-OF SHALL BE INSTALLED Mitsui Fudosan America
E-B.5 E-B.5 AFTER THIS WORK IS COMPLETED. 1251 Avenue of the Americas, Suite 800
(David Leff)
12 OFFICE/RETAIL ARCHITECT
S610-OF 5G Studio Collaborative, LLC.
HSS12X6X3/8 LLH, TYP. 1217 Main St., Suite 500
Dallas, TX 75202
E-C E-C (214-347-4982 Christine Robbins-Elrod)
GFF Architects
TEMP. BRACE 11 2808 Fairmount St., Suite 300
E-1.3 E-1.4 E-1.5 E-1.6 S610A-OF Dallas, TX 75201
E-1.3 E-1.4 E-1.5 E-1.6
ZONING/ENTITLEMENT
Baldwin Associates
LEVEL 02 - PARTIAL DEMO PAN FOR COLUMN JACKET INSTALLATION LEVEL 02 - EXISTING FLOOR OPENING 3904 Elm Street, Suite B
2 SCALE 1/8" = 1'-0" 5 SCALE 1/8" = 1'-0"

Dallas, TX 75226
GEOTECH
NOTE: NOTE: ECS Southwest, LLP
FIREPROOF STEEL TO NOTE: SCAN AND LOCATE EXIST 3033 Kellyway Drive, Suite 110
NOTE:
MEET 2HR. RATING. SCAN AND LOCATE EXIST REINF. REINF. SEE NOTE 7 AND 8 REMOVE EXISTING Carrollton, TX 75006
FIREPROOF STEEL TO
SEE NOTE 7 AND 8 ON FIELD DRILLED ON FIELD DRILLED ANCHOR THICKENED SLAB TO ALLOW NOTE: (972-392-3222 Siddharth Neekhra)
MEET 2HR. RATING
ANCHOR NOTES ON S102-OF. DO NOT NOTES ON S102-OF. DO NOT PLATE CONNECTION SEE 19/S610-OF FOR
CANOPY DAMAGE EXISTING REINF. DAMAGE EXISTING REINF. CIVIL ENGINEER
EXIST. SLAB 7/S610-OF INFO. NOT SHOWN.
SEE S611-OF Kimley-Horn and Associates, Inc.
EXISTING
3'-6" HSS BEAM 13455 Noel Road, Two Galleria Office Tower, Suite 700
STRUCTURE Dallas, TX 75240
LEVEL 3 SEE PLAN
SEE PLAN (972-770-1300 Alex Rathbun)
2 1/2"
(F.V.)
1" GAP
EXIST. SLAB
1'-2" +/-
AND JOIST 1/2" DIA. THRU BOLT LANDSCAPE ARCHITECT

LEVEL 03 LEVEL 03 SWA Group
501'-2" 501'-2" 2001 Irving Boulevard, Suite 157
4" +/-
2"
EXIST. Dallas, TX 75207

9"
1'-8" (F.V.)
LEVEL 3 (214-954-0016 Chuck McDaniel)
JOIST
+/-
1'-6" (F.V.)
4"
L3X3X1/4 BRACE EL. SEE SHEET S200
4" +/-
1/4 STRUCTURAL
6" +/-
Datum Engineers
TYP.
3/16 6516 Forest Park Road
GAP
W.P.
1"
Dallas, TX 75235
2"
2"
4" MIN.
PL.1/2X6X0'-6"
L3X3X3/8, TYP. EACH SIDE 2" MIN. MEP ENGINEER
CEILING 1'-2" +/-
EXIST. ME Engineers, Inc.
TYP. SEE ARCH'L L6X6X3/8 TYP. 13/S610-OF 2" MIN. 1825 Market Center Blvd., Suite 600
CONCRETE 3/16
3/16 PL.3/4X18 X AS SHOWN Dallas, TX 75207
COLUMN 2'-0" +/- W/ DRILL AND EPOXY 4- (214-741-1589 Drew Shivley)
3/4" DIA. X 8" HAS-V-36 W/
HILTI-HIT-RE 500V3 ELEVATOR CONSULTANT
6 8612 Broad Meadow Lane
NEW STEEL COLS. 6 McKinney, TX 75071
SEE DETAIL 16/S610-OF
NOTE:
3/4" = 1'-0" 7 1" = 1'-0" 8 SCAN AND LOCATE EXIST
NOTE:
SCAN AND LOCATE EXIST INTERIOR DESIGNER
3/4" = 1'-0" 6 REINF. SEE NOTE 7 AND 8
ON FIELD DRILLED ANCHOR
REINF. SEE NOTE 7 AND 8
ON FIELD DRILLED ANCHOR
Rottet Studio
NOTES ON S102-OF. DO NOT NOTES ON S102-OF. DO NOT Houston, TX 77002
DAMAGE EXISTING REINF. (713-221-1830 x 6105 Anja Majkic)
DAMAGE EXISTING REINF.
NOTE: NOTE: 8
FIREPROOF STEEL TO SCAN AND LOCATE EXIST
MEET 2HR. RATING. REINF. SEE NOTE 7 AND 8 ON 8
FIELD DRILLED ANCHOR
HANDRAIL
NOTES ON S102-OF. DO NOT 9
SEE ARCH'L www.datumengineers.com | Co. Reg. No. F-2819
COLUMN BEYOND DAMAGE EXISTING REINF. Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
1 Datum Project No. 19166
EXIST. COLUMN 9
EDGE OF SAWCUT TO LINE EXIST. 18"X18"
2 1/2" (F.V.)
DATE ISSUE TITLE

BEYOND COLUMN (F.V.)
UP W/ COLUMN FACE 2 1/2" (F.V.) SEE PLAN
2'-6"
EXIST. SLAB & JOISTS EXISTING LEVEL 2
TO BE REMOVED EXIST. 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
EXISTING LEVEL 2 FRAMING TO BE
6" MAX.
T.O.S.C. EL. 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT

FRAMING TO BE
1"
SEE PLAN DEMOLISHED

EXIST. T.O.S.C. EL. DEMOLISHED 7 10/30/2020 ISSUE FOR PERMIT
8 1/2"
(F.V.)
LEVEL 2 SEE PLAN 12/18/2020 90% CONSTRUCTION DOCUMENTS
1" GAP
8 1/2"
(F.V.)
SEE PLAN HSS LEVEL 02 LEVEL 02 01/25/2021 100% CONSTRUCTION DOCUMENTS
SHIM TIGHT AND PACK SEE PLAN 491'-2" 491'-2"

L4X4X1/2 X 0'-8" TOP AND
W/ N.S. GROUT
SEE PLAN
BOTTOM AT COLUMN
N
M

EXIST. JOIST
AC LU
STL. EL. EXIST. JOIST,

(FIELD VERIFY)
8" +/-
CO
(FIELD VERIFY)
E
= 109'-6"
AT
C. R
TE 1 0 k
PROVIDE 2 1/4" ACCESS HOLE L4X4X1/2 X 0'-5"

G. P. B
P=
HSS, SEE PLAN 1/4

BY M
1'-0" MAX.
1'-0" MAX.
HSS12X6X3/8 GIRT (LLH) SHORE EXISTING
1'-0" +/-
2"
DRILL AND EPOXY 3/4" DIA. X 8" FIREPROOF TO MEET 3 SIDES 5 5 GIRDER DOWN TO
TYP. HAS-V-36 W/ HILTI-HIT-RE 500V3 AT 1/4 1/4 5
1/4 2 HR RATING SHORE EXISTING GIRDER BASEMENT LEVEL.
1'-6" MAX. PROVIDE 1ST ANCHOR 6" SHORE EXISTING P=25k
+/- CLEAR OF COLUMN. SCAN AND CEILING, SEE ARCH'L PL.3/4X18 X AS SHOWN L4X4X1/2 X 1'-4" DOWN TO BASEMENT LEVEL.
GIRDER DOWN
LOCATE EXIST REINF. SEE NOTE 7 W/ DRILL AND EPOXY 4- 3/4" P=25k
TO BASEMENT
P= F C
P= F C
1/4 AND 8 ON FIELD DRILLED ANCHOR DIA. X 8" HAS-V-36 W/ LEVEL. P=25k
O
10 OL
O
10 OL
HILTI-HIT-RE 500V3
kE U
kE U
NOTES ON S102-OF. DO NOT
4" +/-
AC MN
AC MN
DAMAGE EXISTING BEAM REINF.
H .
H .
5
SI
SI
DE
DE
3/4" = 1'-0" 11 1" = 1'-0" 13 REV. DATE ISSUE TITLE
1" = 1'-0" 12 5
4
5
5 .05 12/18/2020 Permit Set Update
DRILL AND EPOXY 3/4" DIA. X 8" SEQUENCING NOTES:

HAS-V-36 W/ HILTI-HIT-RE 500V3 NOTE: 3 TEMP. BRACING BY
FIREPROOF STEEL TO TEMP. BRACING BY
STAGGERED AT 2'-0" +/-. SHORE TO LEVEL 1 THIS WORK SHALL BE PERFORMED AND COMPLETED BEFORE THE NEW LEVEL 2 OPENING GENERAL CONTRACTOR 4
MEET 2HR. RATING. GENERAL CONTRACTOR
SCAN AND LOCATE EXIST REINF. FRAMING TYP. FRAMING WORK PER 5/S610-OF IS STARTED. SEE 3/S610A-OF FOR SEE 3/S610A-OF FOR
SEE NOTE 7 AND 8 ON FIELD 1" N.S. SEE 3/S610A-OF FIELD VERIFY EXISTING FRAMING PRIOR TO START OF THIS WORK. FIELD VERIFY COLUMN ADDN'L INFO. ADDN'L INFO.
DRILLED ANCHOR NOTES ON GROUT FOR ADDN'L INFO. ALIGNMENT BETWEEN LEVELS 1 AND LEVELS 2 AND SCAN AND LOCATE EXISTING COLUMN 17
S102-OF. DO NOT DAMAGE REINFORCEMENT AT BOTH LEVELS PRIOR TO START OF WORK. 2 3
EXISTING COLUMN REINF. CONT. FULL HEIGHT (LEVEL 1 S610-OF 17
PERFORM DEMO AND INSTALLATION ONE COLUMN AT A TIME.
ARCH'L FINISH 2" +/- 2" +/- TO UNDERSIDE OF LEVEL 3) S610-OF
SEE ARCH'L 1" TYP. 1" STEEL PL. JACKET. DO NOT 1. DEMO EXISITING JOIST AND SLAB FRAMING ONLY ON PLAN NORTH AND SOUTH FACES OF
EXIST. COLUMN SPLICE WITHIN 2'-6" OF EXISTING COLUMN. SEE PARTIAL DEMO PLAN 2/S610-OF. NOTE:
EXISTING 2ND LEVEL 2. ERECT STEEL JACKET PLATES ON NORTH AND SOUTH FACES OF COLUMN AND THRU SCAN AND LOCATE EXIST
NEW W8X58 COLUMN OPENING. ASSUME EXISTING BOLT THEM AS SPECIFIED IN DETAIL 17/S610-OF. THESE PLATES SHALL BY-PASS LEVEL 2 REINF. SEE NOTE 7 AND 8
ASSUME 5 TOTAL ( 3 ON COLUMN IS 18X18 (F.V.) FRAMING BY 2'-6". ON FIELD DRILLED ANCHOR
1 3/4" 1 3/4" PLAN NORTH, 2 ON 3. ERECT STEEL JACKET PLATES ON EAST AND WEST FACES OF COLUMN AND THRU BOLT NOTES ON S102-OF. DO NOT 2
1'-6" (F.V.)
PLAN SOUTH)
1'-0" +/-
ACROSS THE COLUMN AS SPECIFIED IN DETAIL 17/S610-OF. THESE PLATES SHALL STOP 2" DAMAGE EXISTING REINF.
2'-0" +/-
BELOW THE EXISTING GIRDER FRAMING INTO THE COLUMN.

4. WELD THE PLATES AT ALL CORNERS PER DETAIL 17/S610-OF.
1'-0" +/-
ACCESS HOLE AS REQUIRED PROVIDE 12"

CONT. WELD AT 5. INSTALL TEMPORARY COLUMN LATERAL BRACING BELOW LEVEL 2 AND INSTALL
TO INSTALL ANCHOR 1/4 3-6 TEMPORARY SHORING UNDER GIRDERS. LATERAL BRACING AND SHORING SHALL BE
1'-0" +/-
ENDS
2'-0" +/-
LEVEL 1 DESIGNED BY A REGISTERED SHORING ENGINEER IN THE STATE OF TX.

EL. SEE SHEET S200 3/4" THRU BOLTS 6. ERECT STEEL JACKET PLATES ON NORTH AND SOUTH FACES OF COLUMN FROM LEVEL 2
LEVEL 01 LEVEL 01
1'-0" +/-
STAGGERED ALONG TO LEVEL 3 AND THRU BOLT THEM AS SPECIFIED IN DETAIL 17/S610-OF. THESE PLATES
COLUMN HEIGHT AT NET PROVIDE 1" N.S. GROUT SHALL STOP 2" BELOW THE EXISTING GIRDER FRAMING INTO THE COLUMN. 481'-2" 481'-2"
1" N.S. GROUT SPACING OF 12" +/- PLACE POCKET ALL AROUND 7. CAREFULLY DEMO 2' STRIP OF GIRDER TO ALLOW STEEL PLATES TO BE INSTALLED ON
IN ALTERNATE DIRECTIONS. 1'-6" (F.V.) EAST AND WEST FACE OF COLUMN.
EXISTING COLUMN.
1"
2" SEE 19 AND 20/S610-OF. PROVIDE ACCESS HOLES IN 8. INSTALL PLATES AND THRU BOLT ON EAST AND WEST FACE OF COLUMN PER DETAIL MAPLE TERRACE
PL.1/2X11X1'-4" MIN. 2" SCAN AND LOCATE EXIST STEEL PLATE FOR GROUT 17/S610-OF. PLATES SHALL STOP 2" BELOW THE EXISTING GIRDER FRAMING INTO THE 3001 MAPLE AVENUE
W/2-3/4" DIA. THRU MIN. REINF. SEE NOTE 7 AND 8 INSTALLATION AS REQ'D COLUMN. DALLAS, TEXAS, 75201
BOLTS W/4X4X1/2 ON FIELD DRILLED ANCHOR 9. BUTT WELD ALL REMAINING JOINTS PER 17/S610-OF.
EXISTING FLOOR OPENING
SHORE
SHORE
NOTES ON S102-OF. DO 10. REMOVE TEMPORARY BRACING.

8" +/-
WASHER AT
UNDERSIDE OF SLAB NOT DAMAGE EXISTING 11. WORK PER 5/S610-OF MAY START AFTER BOTH COLUMN JACKETS HAVE BEEN INSTALLED. 5 5
COLUMN REINF.
PLAN 3/4" = 1'-0" 17 5
19 20
S610-OF
EXISTING COLUMN 3/4" = 1'-0" 3/4" = 1'-0"
3/4" = 1'-0" 16 190013
5 DIAGONAL KICKER
TYP.
S611-OF
BRACKET SEE 5/S611-OF OUTLINE OF CANOPY NOTE:
E-A
6
SEE ARCH'L FOR ADDN'L INFO. 1. ALL EXPOSED STEEL TO BE PAINTED WITH
S611-OF (ASSUME 10 PSF OF RUST INHIBITOR EXTERIOR PAINT, SEE ARCH'L.
W8X31 STRUCTURAL STEEL) 2. GRIND SMOOTH ALL EXPOSED WELDS, TYP.
1/4
1 1/2" (22 GA.) 8
6'-0"
ROOF DECK 6'-0" 6'-0" 3'-6"
W8X10 TYP., U.N.O. 10 9

DEVELOPER
W8X31
W8X31
W8X31
W8X31
W8X31
8/S611-OF 8/S611-OF S611-OF S611-OF
6'-0"
LEVEL 03 Hines
4" +/-
O.H. A/S640-OF NOTE: 3'-0" 3'-0"
501'-2" 2200 Ross Avenue, Suite 4200W
TYP. PERFORM CANOPY WORK AFTER Dallas, TX 75201
COLUMN BRACING WORK PER (972-716-2908 Corbin Eckel)
S610-OF HAS BEEN COMPLETED. W.P.
3'-6"
C8X11.5 C8X11.5 C8X11.5 C8X11.5 2800 Post Oak Blvd., 49th Floor
6"
Houston, TX 77056
E-A
1'-0"
11"
4" (713-621-8000 Juan Delgado)
R
8"
7 EQUITY PARTNERS
4"
3"
21'-1" 21'-1" S611-OF 6"
ø
McNair Interests
1'-
PL.5/16 X AS SHOWN 109 N. Post Oak Lane, Suite 600
10
WT4X15.5
45.0
"
6/S610-OF Houston, TX 77024
CLOSURE PLATE 11 (Drew Steffen)
0°
THICKNESS TO
8"
S611-OF
PL.5/16 X AS SHOWN Mitsui Fudosan America
20/S610-OF
MATCH WT FLANGE
E-B WT4X15.5 BOLTED TO EXISTING
CONCRETE. DRILL & EPOXY 3/4" NEW COLUMN
(David Leff)
DIA. X 10" @ 18" MAX HAS-V-36 SEE S610
W/ HILTI-HIT-RE 500V3. OFFICE/RETAIL ARCHITECT
19/S610-OF
PROVIDE ACORN NUTS AT ALL 5G Studio Collaborative, LLC.
EXPESED ANCHORS. 12 1217 Main St., Suite 500
Dallas, TX 75202
E-B.5 ACCESS HOLES AS REQ'D FOR R7
'-0"
S611-OF (214-347-4982 Christine Robbins-Elrod)
EXPANSION BOLT INSTALLATION.
PLUG WELD HOLES AFTER ANCHOR MASTER/MULTIFAMILY ARCHITECT
6/S610-OF INTALLATION AND GRIND SMOOTH GFF Architects
Dallas, TX 75201
3"
5"
LEVEL 02
491'-2" ZONING/ENTITLEMENT
E-C Baldwin Associates
6" +/-
E-1.3 E-1.4 E-1.5 E-1.6 SCAN AND LOCATE EXIST /2" (214-824-7949 Robert Baldwin)
REINF. SEE NOTE 7 AND 8 ON 11
R
FIELD DRILLED ANCHOR NOTES 2"
7'-3 3/8" GEOTECH
ON S102-OF. DO NOT DAMAGE
ECS Southwest, LLP
1/8" = 1'-0" 2 EXISTING REINF. 1/2" = 1'-0" 5 3033 Kellyway Drive, Suite 110
CIVIL ENGINEER
NOTE: Kimley-Horn and Associates, Inc.
SCAN AND LOCATE EXIST 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
REINF. SEE NOTE 7 AND 8 ON NOTE: (972-770-1300 Alex Rathbun)
FIELD DRILLED ANCHOR SEE 9/S611-OF FOR
NOTES ON S102-OF PRIOR TO INFO. NOT SHOWN.
SEE PLAN LANDSCAPE ARCHITECT
CHANNEL FABRICATION. DO 7/S611-OF
BEAM SWA Group
NOT DAMAGE EXISTING REINF. BEAM
SEE PLAN 2001 Irving Boulevard, Suite 157
SEE PLAN DECK, (214-954-0016 Chuck McDaniel)
SEE PLAN FOR 1/2"
ORIENTATION MAX. T.O.S. EL. T.O.S. EL.
DRILL & EPOXY 3/4" DIA. X 6" SEE PLAN STRUCTURAL
@ 2'-0" O.C. MAX HAS-V-36 PL.5/16" SEE PLAN
Datum Engineers
EXIST. T.O.S.C. EL. W/ HILTI-HIT-RE 500V3 SEE ELEVATION 6516 Forest Park Road
T.O.S. EL. SEE PLAN Dallas, TX 75235
SEE PLAN GRIND
6"
12" CONT. WT FRAME SMOOTH 1/4 T.O.S. EL.
1'-6" (F.V.)
T.O.S. EL. WELD AT EA. SEE PLAN AND VARIES MEP ENGINEER
SEE PLAN END 1/4 3-12 ELEVATION
2" SEE ARCH'L ME Engineers, Inc.
L3X3X1/4X CONT. 6"
CHANNEL, 1825 Market Center Blvd., Suite 600
T.O.S. EL.
6" +/-
SEE PLAN PL.5/16" Dallas, TX 75207

VARIES (214-741-1589 Drew Shivley)
BEAM, WT FRAME
SEE ARCH'L
SEE PLAN SEE PLAN AND ELEVATOR CONSULTANT
3/16 3-12 BEAM, ELEVATION Persohn | Hahn Associates, Inc.
CHANNEL SEE PLAN 8612 Broad Meadow Lane
SEE PLAN McKinney, TX 75071
INTERIOR DESIGNER
1'-0" (F.V.) Rottet Studio
Houston, TX 77002
1" = 1'-0" 6 1" = 1'-0" 7 1" = 1'-0" 8 3/4" = 1'-0" 9 3/4" = 1'-0" 10 (713-221-1830 x 6105 Anja Majkic)
NOTE:
1. EXISTING FRAMING ABOVE LEVEL 1 TO BE FIELD VERIFIED NOTE:
ONCE FINISHES HAVE BEEN REMOVED. 1. EXISTING FRAMING ABOVE LEVEL 1 TO www.datumengineers.com | Co. Reg. No. F-2819
BE FIELD VERIFIED ONCE FINISHES
2. FRAMING IS FOR BIDDING PURPOSES ONLY AND SUBJECT TO
HAVE BEEN REMOVED.
E2 E-2.3 214-358-0174 512-469-9490 210-858-2880
GRIND CHANGE AFTER FIELD VERIFICATION. REFER TO EXISTING Datum Project No. 19166
WT AT CANOPY 2. FRAMING IS FOR BIDDING PURPOSES
SMOOTH 1/4 CONDITIONS GENERAL NOTES FOR ADDITIONAL INFORMATION. DATE ISSUE TITLE
SEE PLAN AND ELEVATION ONLY AND SUBJECT TO CHANGE AFTER
WT AT CANOPY WT AT CANOPY FIELD VERIFICATION. REFER TO
SEE PLAN AND ELEVATION SEE PLAN AND ELEVATION EXISTING CONDITIONS GENERAL 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
CIRCULAR PL.5/16" 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
STUCCO FINISH NOTES FOR ADDITIONAL INFORMATION.
SEE ELEVATION
SEE ARCH'L STUCCO FINISH 10 E-1.7 11
08/31/2020
10/30/2020
ISSUE FOR PERMIT
GRIND GRIND SEE ARCH'L 12/18/2020 90% CONSTRUCTION DOCUMENTS
SMOOTH 1/4 SMOOTH 1/4 01/25/2021 100% CONSTRUCTION DOCUMENTS
STOREFRONT 7'-10" (F.V.)
SEE ARCH'L STOREFRONT E-C
SEE ARCH'L
15
SLAB-ON-DECK, SEE S613-OF
GENERAL NOTES, TYP.
TYP. 14
S613-OF
A C6X8.2
8'-4 3/8" (F.V.)
EXISTING CONCRETE 5'-10" (F.V.)

C6X8.2
C6X8.2
COLUMN, SEE PLAN
6'-11 1/2" (F.V.)

EXISTING CONCRETE 15
COLUMN, SEE PLAN SLAB-ON-DECK, SEE
NEW STEEL COLUMN E-A GENERAL NOTES, TYP.
C6X8.2 S613-OF
SEE S610-OF REV. DATE ISSUE TITLE
1" = 1'-0" 11 1" = 1'-0" 12
C6X13 E-2
14
15
S613-OF 7'-8" (F.V.)
S613-OF
7'-6 3/4" (F.V.)

C6X8.2
14
7'-0 3/4" (F.V.)
S613-OF
5'-3" (F.V.)
C6X8.2
C6X8.2
C6X13
A8
E-B 14
15 B S613-OF
S613-OF
TYP.
E-4
MAPLE TERRACE
3001 MAPLE AVENUE
STEEL SECTIONS AND DETAILS
19 STAIR AND ELEVATOR OPENING INFILL 20 STAIR AND ELEVATOR OPENING INFILL
1/4" = 1'-0" 1/4" = 1'-0"
190013
PROJECT NUMBER
PROVIDE 3X3 W1.4X1.4 SPALL OR
APPROXIMATE EXISTING
W.W.M. WHERE OPENING IS
1'-0" OR GREATER AND
DELAMINATION NOTE:
1. PROVIDE SPRAY APPLIED FIREPROOFING AT ALL EXPOSED CONCRETE REPAIR
REINFORCEMENT LOCATIONS THERE IS NO EXISTING SLAB FOR OPENINGS LARGER THAN 9" IN REINFORCING AND ABANDONED BACK BOXES AT
INTERIOR 1. DETAILS ON THIS SHEET ARE TYPICAL FOR THE ENTIRE PROJECT.
TYP. REINF. ANY DIMENSION SLOPE SIDES BACK UNDERSIDE OF EXISTING SLABS.
TO APPROXIMATELY 3 VERTICAL TO 1
PROVIDE MIN. 3/4"

2. APPROXIMATE QUANTITIES OF REQUIRED FIREPROOFING
WHERE NO EXISTING ROUGHEN SURFACE, HORIZONTAL 2. APPROXIMATE QUANTITIES AND LOCATIONS ARE CALLED OUT ON PLANS BASED ON WHAT
ARE SHOWN ON PLAN FOR BIDDING. CONTRACTOR SHALL
OF COVER
REINFORCING EXISTS AND TYP. WAS VISIBLE AT THE TIME OF OBSERVATION, HOWEVER ADDITIONAL HIDDEN CONDITIONS
3X3 W1.4xW1.4 W.W.M. APPROXIMATE EXISTING SURVEY EXISTING STRUCTURE AND PROVIDE AT ALL
EXISTING BEAM PATCH IS 2" OR DEEPER ADD REQUIRING REPAIR MAY ARISE AS CONSTRUCTION PROGRESSES. ALLOW FOR AN
EXISTING SLAB REINFORCEMENT LOCATIONS, EXPOSED STEEL AT UNDERSIDES OF EXISTING SLABS.
MESH AND EPOXIED ADDITIONAL 10% FOR EACH REPAIR BEYOND WHAT IS SHOWN ON PLAN TO ACCOUNT FOR
DOWELS AS PER 6/S612-OF. TYP. THESE POTENTIAL HIDDEN ITEMS.
GRIND, CHIP, OR SAW EXISTING EXPOSED
CUT AROUND PATCH REINFORCING DEVELOPER
PATCH EXISTING SPALLS AND 3. CONCRETE THAT HAS ANY DELAMINATIONS, HONEYCOMBING, OR SPALLS DEEPER THAN 3/4"
PERIMETER TO SOUND UNSOUND OR HONEYCOMBED ABANDONED BACK BOXES Hines
OR IF REINFORCEMENT IS EXPOSED SHALL BE REPAIRED. 2200 Ross Avenue, Suite 4200W
CONCRETE CONCRETE AS NOTED BELOW, REMOVE EXISTING WINDOW EXISTING SLAB WHERE OCCUR
Dallas, TX 75201
TYP. EXIST. FRAMES AS REQUIRED TO PATCH 4. REPAIR MATERIALS (INSTALL ALL MATERIALS IN COMPLIANCE WITH MANUFACTURER'S (972-716-2908 Corbin Eckel)
EXPOSED EXPOSED REINFORCING INSTRUCTIONS AND RECOMMENDATIONS):
REINF. 2800 Post Oak Blvd., 49th Floor
GRIND, CHIP, OR SAW CUT PATCH EXISTING SPALLS AND A. BONDING AND ANTI-CORROSION AGENT: Houston, TX 77056
ROUGHEN SURFACE, SPALL OR DELAMINATION, (A) CONDITION AT EXPOSED BOTTOM BARS (713-621-8000 Juan Delgado)
AROUND PATCH PERIMETER UNSOUND OR HONEYCOMBED SIKA ARMATEC 110 EPOCEM – SIKA
TYP. TYP. TO SOUND CONCRETE. CONCRETE AS NOTED BELOW. STO BONDING AND ANTI-CORROSION AGENT (80246) - STO CORPORATION
MASTEREMACO P 124 (FORMERLY EMACO P24) – BASF EQUITY PARTNERS
NOTES: B. PATCHING MORTAR FOR HORIZONTAL REPAIRS: McNair Interests
1. REFER TO "CONCRETE REPAIR" GENERAL NOTES FOR REPAIR MATERIALS AND INTERIOR CAUTION: SLAB MAY HAVE EMBEDDED ELECTRICAL CONDUITS. VERIFY LOCATION PRIOR TO SIKATOP 122 PLUS - SIKA 109 N. Post Oak Lane, Suite 600
PROCEDURES. EXTEND FIREPROOFING A STO TROWEL-GRADE MORTAR WITH CI (80701) - STO CORPORATION Houston, TX 77024
COMMENCEMENT OF WORK. (Drew Steffen)
#3 DRILLED ADHESIVE DOWELS @ MINIMUM OF 1'-0" BEYOND MASTEREMACO T 310CI (FORMERLY EMACO R310 CI) - BASF
PREP. SURFACE AND CLEAN
2. WHERE DIMENSION "A" SHOWN IN DETAIL IS 4" OR LESS, REPAIR ENTIRE WIDTH OF BEAM. 12" W/ 3" EMBED. NOTES: LAST EXPOSED BAR C. PATCHING MORTAR FOR OVERHEAD/VERTICAL REPAIRS:
EXISTING REINFORCING PER Mitsui Fudosan America
EXISTING BEAM 1. REFER TO "CONCRETE REPAIR" GENERAL NOTES FOR REPAIR MATERIALS AND P MANUFACTURER'S WRITTEN SIKATOP 123 PLUS - SIKA 1251 Avenue of the Americas, Suite 800
3. WHERE REINFORCEMENT THAT IS EXPOSED DURING SURFACE PREPARATION IS FOUND ROCEDURES. STO OVERHEAD MORTAR WITH CI (80702) - STO CORPORATION New York, New York 10020
2" INSTRUCTIONS
TO BE SEVERELY CORRODED OR HAS LOST 10% OR MORE OF ITS CROSS SECTIONAL
3/4" OF COVER
PROVIDE MIN.
3X3 W1.4xW1.4 W.W.M. FOR 2. WHERE REINFORCEMENT THAT IS EXPOSED DURING SURFACE PREPARATION IS FOUND TO BONDING AGENT APPROVED BY THE MASTEREMACO N 420CI (FORMERLY EMACO R310 CI) - BASF (David Leff)
AREA, SUPPLEMENTARY REINFORCEMENT MAY BE REQUIRED. REPORT TO ENGINEER PATCHES 2" AND DEEPER BE SEVERELY CORRODED OR HAS LOST 10% OR MORE OF ITS CROSS SECTIONAL AREA,
FOR REVIEW AND DESIGN OF SUPPLEMENTARY REINFORCEMENT. FIREPROOFING MANUFACTURER AND
2"
SUPPLEMENTARY REINFORCEMENT MAY BE REQUIRED. REPORT TO ENGINEER FOR REVIEW SPRAY APPLIED CEMENTITIOUS 3. REPAIR PROCEDURE SHALL BE AS FOLLOWS: OFFICE/RETAIL ARCHITECT
AND DESIGN OF SUPPLEMENTARY REINFORCEMENT. FIREPROOFING (MONOKOTE 5G Studio Collaborative, LLC.
4. PROVIDE TEMPORARY SHORING WHEREVER DEPTH OF CONCRETE REMOVAL EXCEEDS 3. PROVIDE TEMPORARY SHORING WHEREVER REMOVAL OF UNSOUND CONCRETE IS LARGER A. PROVIDE TEMPORARY SHORING AS NOTED IN THE DRAWINGS. 1217 Main St., Suite 500
10"
2" ON ANY SURFACE. MK-10/HB) APPLIED AS PER
THAN 1'-6" IN LENGTH PERPENDICULAR TO SLAB SPAN DIRECTION. B. PROTECT EXISTING REINFORCEMENT AND ANY OTHER ITEMS (EMBEDS, ELECTRICAL Dallas, TX 75202
SPECIFICATIONS TO MEET UL-J712. (214-347-4982 Christine Robbins-Elrod)
CONDUIT, ETC.) IN THE CONCRETE DURING SAWCUTTING, GRINDING, OR CHIPPING. USE
CONCRETE BEAM REPAIR EXTEND PATCH TO SIDE AS SHOWN FULL DEPTH SLAB REPAIR NON-DESTRUCTIVE METHODS TO LOCATE AND MARK THESE ITEMS PRIOR TO CONCRETE
FIREPROOFING OF EXISTING EXPOSED STEEL MASTER/MULTIFAMILY ARCHITECT
WHERE REQUIRED TO MAINTAIN MIN.
TYPICAL DETAIL 1 3/4" COVER ON EXPOSED SIDE BAR. TYPICAL DETAIL 3 TYPICAL DETAIL 4
REMOVAL.
C. REMOVE HONEYCOMB, DELAMINATED, SPALLED, AND UNSOUND CONCRETE TO A GFF Architects
PATCH SHALL BE FULL LENGTH OF NO SCALE MINIMUM DEPTH OF 3/4" BY SAWCUTTING OR GRINDING PERPENDICULAR TO THE
NO SCALE BEAM, SEE BELOW AT MASONRY NO SCALE Dallas, TX 75201
SURFACE AT LEAST 1/2" BEYOND THE AREA REQUIRING REPAIR. GRIND OR CHIP OUT
(B) CONDITION AT EXPOSED BOTTOM & SIDE BARS PIECES USING A 30 LB. MAX CHIPPING HAMMER TO SOUND CONCRETE. PATCH AREA
SHALL BE SQUARE OR RECTANGULER WITH STRAIGHT EDGES.
ROUGHEN SURFACE, APPROXIMATE EXISTING NOTE: D. ROUGHEN EXISTING SURFACE TO ICRI CONCRETE SURACE PROFILE (CSP) 10 (MIN. 1/4" ZONING/ENTITLEMENT
TYP. REINFORCEMENT LOCATIONS, INSTALLATION MUST PRECISELY MATCH AMPLITUDE). Baldwin Associates
TYP. MANUFACTURER'S INSTRUCTIONS. E. RUSTED REINFORCEMENT SHALL BE FULLY EXPOSED WITH 3/4" CLEARANCE ALL 3904 Elm Street, Suite B
Dallas, TX 75226
#3 DRILLED ADHESIVE DOWELS @ EXISTING SLAB AROUND. CONTINUE TO REMOVE CONCRETE UNTIL NON-RUSTED REINFORCEMENT IS
INTERIOR (214-824-7949 Robert Baldwin)
12" W/ 3" EMBED. FOR PATCHES 2" EXPOSED. IMMEDIDATELY BEFORE PATCHING, CLEAN ON ALL SIDES OF EXPOSTED
T/2 MAX.
VARIES
AND DEEPER EXISTING BEAM REINFORCEMENT USING ABRASIVE METHODS, SUCH AS WIRE BRUSHES, SAND- GEOTECH
THICKNESS
INTERIOR BLASTING, OR WATER BLASTING.
ECS Southwest, LLP
SLAB
3/4" OF COVER
F. WHERE REINFORCEMENT THAT IS EXPOSED DURING SURFACE PREPARATION IS FOUND
PROVIDE MIN.
SEE ABOVE FOR INFO. NOT 3033 Kellyway Drive, Suite 110
SHOWN TO BE SEVERELY CORRODED OR HAS LOST 10% OR MORE OF ITS CROSS SECTIONAL Carrollton, TX 75006
3X3 W1.4xW1.4 W.W.M. FOR THOROUGHLY CLEAN EXPOSED AREA, SUPPLEMENTARY REINFORCEMENT MAY BE REQUIRED. REPORT TO ENGINEER (972-392-3222 Siddharth Neekhra)
EXISTING BEAM PATCHES 2" AND DEEPER SURFACE & COAT W/ BONDING FOR REVIEW AND DESIGN OF SUPPLEMENTARY REINFORCEMENT.
AGENT (SIKA ARMATEC 110 EPOCEM) G. APPLY ANTI-CORROSION AGENT TO EXPOSED REINFORCEMENT. CIVIL ENGINEER
FILL VOID W/ SIKA REPAIR SHB. H. ENSURE EXISTING CONCRETE IS CLEAN AND SURFACE IS PREPARED IN STRICT
GRIND, CHIP, OR SAW CUT PATCH EXISTING SPALLS AND Kimley-Horn and Associates, Inc.
ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS BEFORE APPLYING 13455 Noel Road, Two Galleria Office Tower, Suite 700
AROUND PATCH PERIMETER UNSOUND OR HONEYCOMBED
T.O.S.C. EL. PATCHING MORTAR. Dallas, TX 75240
TO SOUND CONCRETE CONCRETE AS NOTED BELOW.
EXISTING MASONRY WALL TO I. APPLY PATCHING MORTAR IN STRICT ACCORDANCE WITH THE MANUFACTURER’S (972-770-1300 Alex Rathbun)
PATCH EXISTING UNSOUND OR
SLAB THICK.
REMAIN, DO NOT DEMO. BRICK SPALL OR INSTRUCTIONS.
HONEYCOMBED CONCRETE AS DELAMINATION LANDSCAPE ARCHITECT
T=<3"
NOTED BELOW (C) CONDITION AT EXPOSED SIDE BARS AT MASONRY WALL
SWA Group
NOTES: CAUTION: SLAB MAY HAVE EMBEDDED ELECTRICAL CONDUITS. VERIFY LOCATION PRIOR TO COLUMN REPAIR SEQUENCE 2001 Irving Boulevard, Suite 157
Dallas, TX 75207
1. EPOXY INJECT (E) CRACKS IN BEAM PRIOR TO REMOVAL OF COMMENCEMENT OF WORK. 1. REMOVE DETERIORATED CONCRETE TO REINFORCING BARS ONLY. DO NOT REMOVE (214-954-0016 Chuck McDaniel)
NOTES: UNSOUND CONCRETE. DETERIORATED CONCRETE PAST REINFORCING BARS.
1. REMOVE UNSOUND CONCRETE AND REPAIR SIMILAR TO 1/S612-OF 2. REMOVE UNSOUND CONCRETE AND REPAIR SIMILAR TO 1/S612-OF NOTES: STRUCTURAL
T.O.S.C. EL.
WITH ADDITIONAL MARKUPS SHOWN HERE. WITH ADDITIONAL MARKUPS SHOWN HERE. 1. REFER TO "CONCRETE REPAIR" GENERAL NOTES FOR REPAIR MATERIALS AND 2. REMOVE AND REPLACE BROKEN TIES OR STIRRUPS AND TIES OR STIRRUPS WITH MORE Datum Engineers
3. PROVIDE TEMPORARY SHORING WHEREVER DEPTH OF CONCRETE PROCEDURES. THAN 10% SECTION LOSS PER 18/S612-OF. ONLY ONE TIE OR STIRRUP SHALL BE REMOVED 6516 Forest Park Road
REMOVAL EXCEEDS 2" ON ANY SURFACE. 2. WHERE REINFORCEMENT THAT IS EXPOSED DURING SURFACE PREPARATION IS FOUND AND REPLACED AT A TIME. Dallas, TX 75235
4. CRITCAL TO USE LIGHT WEIGHT DEMOLITION EQUIPMENT AS TO BE SEVERLEY CORRODED OR HAS LOST 10%OR MORE OF IT'S CROSS SECTIONAL (214-358-0174 Rodolfo D'Arlach)
REQUIRED TO PROTECT BUILDING FACAD FROM DAMAGE. AREA, SUPPLEMENTARY REINFORCEMENT MAY BE REQUIRED. REPORT TO ENGINEER SEE NOTES ABOVE 3. DETERMINE IF ANY EXPOSED VERTICAL REINFORCING BARS HAVE LOST MORE THAN 10% OF
5. COORDINATE HEADER REPAIRS WITH WINDOW FRAME REPAIR & FOR REVIEW AND DESIGN OF SUPPLEMENTARY REINFORCEMENT. THEIR ORIGINAL AREA . IF MORE THAN 10% SECTION LOSS IS DISCOVERED NOTIFY ENGINEER MEP ENGINEER
REPLACEMENT AS REPAIRED HEADERS MAY ENCROACH ON 3. PROVIDE TEMPORARY SHORING WHEREVER DEPTH OF CONCRETE REMOVAL EXCEEDS AND REFER TO DETAIL 17/S612-OF TO INSTALL THE CONCRETE JACKET. ME Engineers, Inc.
ORIGINAL ROUGH OPENING DIMENSIONS. SEE ARCHITECTURAL 3" AND FOR ANY AREAS WITH REMOVAL OF UNSOUND CONCRETE LARGER THAN 3'-0" IN 1825 Market Center Blvd., Suite 600
FOR ADDITIONAL INFORMATION. LENGTH PERPENDICULAR TO SLAB SPAN DIRECTION. 4. IF 10% SECTION LOSS OF ANY VERTICAL REINFORCING BAR IS NOT DISCOVERED CONTINUE Dallas, TX 75207
REMOVAL OF DETERIORATED CONCRETE ON ONE SIDE OF THE COLUMN ONLY. ADDITIONAL
CONCRETE BEAM REPAIR - PATCH DEEPER THAN 2" REPAIR AT BOTTOM OF PERIMETER BEAMS PARTIAL DEPTH SLAB REPAIR SLAB REPAIR - PAN JOIST SLAB REMOVAL SHALL NOT EXCEED 1" PAST VERTICAL REINFORCEMENT INTO THE COLUMN. IF
DETERIORATED CONCRETE CONTINUES PAST 1" CONTACT ENGINEER. ELEVATOR CONSULTANT
TYPICAL DETAIL 6 TYPICAL DETAIL 7 TYPICAL DETAIL 8 TYPICAL DETAIL 9 Persohn | Hahn Associates, Inc.
NO SCALE NO SCALE NO SCALE 5. ONCE REMOVAL IS COMPLETE ON ONE SIDE ONLY PATCH AREAS OF ADDITIONAL REMOVAL
NO SCALE McKinney, TX 75071
FROM STEP 4 TO THE INTERFACE OF THE CONCRETE REMOVAL DONE IN STEP 1. (972-832-4232 Tom Williams)
2 TIES @ 2"
6. ONCE PATCH MATERIAL ON THE SIDE REPAIRED IN STEP 5 REACHES 2000 PSI MOVE TO STEP INTERIOR DESIGNER
7.
Rottet Studio
7. COMPLETE STEPS 4 TO 6 FOR THE OTHER THREE SIDES OF THE COLUMN, OR TWO SIDES FOR Houston, TX 77002
EXIST. COLUMN APPROXIMATE EXISTING COLUMNS FRAMING INTO A CONCRETE WALL. (713-221-1830 x 6105 Anja Majkic)
REINFORCEMENT, TYP.
4"
CHIP, GRIND, OR SAW CUT TO

ROUGHEN SURFACE, 8. PATCH BACK THE CONCRETE THAT WAS REMOVED IN STEP 1.
REMOVE DAMAGED STIRRUP.
TYP. REMOVE CONCRETE TO SOUND EXIST. CONC.
6" OC (TYP)
CONCRETE, IF REMOVAL REQUIRED COLUMN ROUGHEN SURFACE

SECT
TYP. CONCRETE CRACK REPAIR

A
IS MORE THAN 1" PAST VERTICAL
SECT.
REINFORCEMENT STOP REPAIR
A
AND CONTACT ENGINEER REMOVE MINIMUM 3/4" 1. CRACKS WIDER THAN 0.030” SHALL BE EPOXY INJECTED TO RESTORE STRUCTURAL 214-358-0174 512-469-9490 210-858-2880
BEHIND EXPOSED REINF., INTEGRITY. Datum Project No. 19166

REMOVAL LIMITS DRILLED ADHESIVE IF ANY
VARIES
DATE ISSUE TITLE
#3 TO REPLACE 2. EPOXY INJECTION SHALL BE PERFORMED IN ACCORDANCE WITH ACI 503.7-07 “SPECIFICATION
(TYP.) DOWELS @ 12" OC, REMOVED DAMAGED 04/03/2020 SCHEMATIC DESIGN PRESENTATION
EXIST. VERTICAL FOR CRACK REPAIR BY EPOXY INJECTION.”
EMBED 6" MIN (NOTE 3) EXISTING STIRRUP 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
REINFORCEMENT SPALL OR 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
NEW JACKET TO REMAIN DELAMINATION 3. EPOXY INJECTION SHALL BE PERFORMED WITH SIKADUR 35, HI-MOD LV LPL BY SIKA 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
PATCH EXISTING SPALLS REINF., NOTE 4 CORPORATION, LYNHURST, NEW JERSEY OR APPROVED EQUAL.
ROUGHEN EXISTING 10/30/2020 ISSUE FOR PERMIT
AND UNSOUND OR CONCRETE, TYP. PATCH EXISTING SPALLS 12/18/2020 90% CONSTRUCTION DOCUMENTS
HONEYCOMBED CONCRETE APPROXIMATE EXISTING AND UNSOUND OR 4. EPOXY ADHESIVE SHALL BE INJECTED AS FOLLOWS:
PER 19/S612-OF REINFORCEMENT LOCATIONS, TYP. HONEYCOMBED CONC.
A. ALL SURFACES TO WHICH EPOXY ADHESIVE IS TO BE APPLIED SHALL BE FREE OF ALL
NEW CONC AS NOTED BELOW
LOOSE AND UNSOUND MATERIAL, OIL, GREASE, WAX, DIRT, AND EXISTING COATINGS.
JACKET, NOTE 2 B. INSTALL EPOXY ADHESIVE INJECTION PORTS ACCORDING TO SUBMITTED RESERVED FOR REVIEWERS NOTES
RECTANGULAR COLUMNS ELEVATION RECOMMENDATIONS OF THE EPOXY MANUFACTURER.
SAWCUT, CHIP, REMOVE AND REPLACE
C. APPLY AN EPOXY SURFACE SEAL TO PREVENT ESCAPE OF THE INJECTED ADHESIVE,
EXISTISTING SLAB-ON-GRADE AS REQD MATCH EXIST. WHICH MEETS THE SUBMITTED RECOMMENDATIONS OF THE EPOXY MANUFACTURER.
CHIP, GRIND, OR SAW D. AFTER CURING OF EPOXY SEALANT, WATER SHALL BE INJECTED INTO THE CRACK TO
EXIST. VERTICAL CUT TO REMOVE COVER
REINFORCEMENT TO FLUSH OUT DEBRIS AND TO DETERMINE ANY TROUBLE SPOTS ALONG LENGTH OF CRACK.
AROUND DAMAGED CORRECT ALL PROBLEM LOCATIONS AS REQUIRED.
REMAIN STIRRUP. ONCE EXPOSED APPROXIMATE E. EPOXY INJECTION SHALL BEGIN AT THE ENTRY PORT OF LOWEST ELEVATION. WHEN
FIELD VERIFY
REMOVE DAMAGED REINFORCEMENT PURE RESIN APPEARS AT THE ADJACENT PORT, PLUG THE PORT BEING INJECTED AND
STIRRUP. REMOVE LOCATIONS, TYP. BEGIN INJECTION AT THE ADJACENT PORT. REPEAT PROCEDURE UNTIL ALL PORTS HAVE
FIELD VERIFY
CONCRETE TO SOUND BEEN INJECTED.

CONCRETE, IF REMOVAL F. AFTER SET OF EPOXY ADHESIVE, REMOVE PORTS AND ALL OF THE EPOXY SEALER FROM
REQUIRED IS MORE THAN EXPOSED SURFACES.
MATCH EXIST.
1" PAST VERTICAL ROUGHEN SURFACE,

REINFORCEMENT STOP TYP.
EMBED VERTICAL REPAIR AND CONTACT
ENGINEER
STRUCTURAL REPAIR QUANTITIES REV. DATE ISSUE TITLE
BARS 6" MIN CHIP, GRIND, OR SAW CUT PATCH EXISTING SPALLS AND .05 12/18/2020 Permit Set Update
STRUCURAL REPAIR QUANTITIES
AROUND PATCH UNSOUND OR HONEYCOMBED
EXIST FOOTING BELOW EXIST PERIMETER TO SOUND CONCRETE AS NOTED BELOW DESCRIPTION QUANTITIES
SLAB-ON-GRADE, REINF NOT #3 TO REPLACE CONCRETE. (PER 1000 SF OF FLOOR AREA)
SHOW FOR CLARITY REMOVED DAMAGED
SLAB CRACK REPAIR 10 SF
DRILLED ADHESIVE EXISTING STIRRUP
STAGGER HOOK DWL., TYP.
LOCATIONS, TYP. SLAB SPALL-HORIZONTAL REPAIR 5 SF
GRID JACKET JACKET COLUMN TYPE, NUMBER OF
EXIST. A
LOCATION HEIGHT THICKNESS WALL OR VERTICAL CORNER PROFILE AT
SEE SCHEDULE (FT) (IN) RECTANGULAR BARS BASEMENT SLAB SPALL-OVERHEAD REPAIR 35 SF
WALL REPAIR LOCATIONS TO
BOILER WIDTH OF COLUMN MATCH EXISTING
4#5 DRILLED FULL HEIGHT 4 RECTANGULAR "A" 12#7 COLUMN SPALL-VERTICAL REPAIR 20 SF
ROOM (3) (F.V.) CONDITION
ADHESIVE DWLS. BOILER
FULL HEIGHT 4 WALL "B" 8#7 BEAM/JOIST SPALL-VERTICAL OR OVERHEAD REPAIR 30 SF
W/STD. HOOK ROOM (2)
SECTION "A"
#4 TIES @ 6" O.C. WALL COLUMNS NOTES:
1. QUANTITIES ARE ESTIMATED BASED ON LIMITED FIELD OBSERVATIONS. WHERE
FINISHES HAVE OBSCURED REVIEW, REPAIR QUANTITIES HAVE BEEN
APPROXIMATED TO ACCOUNT FOR POTENTIAL HIDDEN CONDITIONS. QUANTITIES
NOTES: ARE FOR BIDDING PURPOSES ONLY. FINAL REPAIR LOCATIONS WILL BE
NOTES: 1. REFER TO "CONCRETE REPAIR" NOTES FOR REPAIR MATERIALS AND PROCEDURES AND
RECTANGULAR COLUMNS 1. REFER TO "CONCRETE REPAIR" NOTES FOR REPAIR MATERIALS AND PROCEDURES AND NOTES: DETERMINED ONCE ALL FINISHES HAVE BEEN REMOVED.
SECTION "A" 1. REFER TO "CONCRETE REPAIR" NOTES FOR REPAIR MATERIALS AND PROCEDURES "COLUMN REPAIR SEQUENCE" NOTES.
"COLUMN REPAIR SEQUENCE" NOTES.
ANDC"COLUMN REPAIR SEQUENCE" NOTES. 2. QUANTITIES ARE BASED ON DETERIORATION OBSERVED IN THE BASEMENT LEVEL
SEE SCHEDULE 2. WHERE COLUMN SHEAR REINFORCEMENT (TIES OR SPIRAL) THAT IS EXPOSED 2. WHERE DIMENSION "A" SHOWN IN SECTION IS 4" OR LESS, THEN REPAIR ENTIRE WIDTH
2. REFER TO "CONCRETE REINFORCEMENT" GENERAL NOTES FOR COVER BOILER ROOM.
4#5 DRILLED DURING SURFACE PREPARATION IS FOUND TO BE SEVERELY CORRODED, HAS LOST OF COLUMN.
REQUIREMENTS ON NEW JACKET REINFOREMENT.
ADHESIVE DWLS. 10% OR MORE OF ITS CROSS SECTIONAL AREA, OR HAS FRACTURED 3. QUANTITIES ARE BASED ON THE AMOUNT OF REPAIR REQUIRED FOR EVERY 1000
W/STD. HOOK 3. EMBED DRILLED ADHESIVE DOWELS A MN. OF 6". REFER TO "DRILLED ADHESIVE SUPPLEMENTARY REINFORCEMENT AS SHOWN HERE WILL BE REQUIRED. SQUARE FEET OF FLOOR AREA.
DOWEL" GENERAL NOTES. 3. EMBED DRILLED ADHESIVE DOWELS A MON. OF 6". REFER TO "DRILLED ADHESIVE
#4 TIES @ 6" O.C. DOWEL" GENERAL NOTES. 4. QUANTITIES SHALL BE APPLIED OVER THE ENTIRE LEVEL 01 FLOOR AREA (FLOOR
ABOVE THE BASEMENT) MAPLE TERRACE
3001 MAPLE AVENUE
5. 50% OF THE QUANTITIES SHOWN SHALL BE APPLIED OVER THE ENTIRETY OF LEVEL
EXIST BASEMENT 02 TO LEVEL 07. DALLAS, TEXAS, 75201
WALL
6. QUANTITIES SHALL BE APPLIED OVER THE ENTIRE ROOF AREA.
CONCRETE REPAIR DETAILS
CONCRETE COLUMN JACKET REPAIR CONCRETE COLUMN STIRRUP REPAIR CONCRETE COLUMN REPAIR
7. REFER TO CONCRETE REPAIR NOTES AND DETAILS FOR REPAIR PROCEDURE.
WALL COLUMNS TYPICAL DETAIL TYPICAL DETAIL TYPICAL DETAIL
SECTIONS "B" NO SCALE
17 NO SCALE
18 NO SCALE
19 8. REFER TO CONCRETE CRACK REPAIR NOTES FOR REPAIR PROCEDURE. 20 190013
PROJECT NUMBER
NOTE:
1. DO NOT OVERCUT OPENING DRILL CORNERS
AS SHOWN OR USE PLUNGE-CUTTING SAWS. NOTE:
2. ALL NEW OPENINGS NOT SHOWN ON DWGS. #5X3'-0" DEILLED ADHESIVE FOR PLUMBING TRENCHING,
NEED TO BE APPROVED BY ENGINEER. DOWELS W/ 12" EMBED, EXIST. CONC. COORDINATE WITH PLUMBING
3. DO NOT CORE OR CUT THRU BEAMS, OR STEMS TYP. ALL SIDES OF WALL FOR EXTENTS AND SIZES OF
OPENING ACCESS TRENCHES TO
INSTALL NEW PLUMBING LINES.
EXISTING WALL
OR SLAB DEVELOPER
ALLOWABLE FLOOR 3" 1'-0"
#4@12" E.W. EA. FACE, #3 X AS REQ'D DWL @ 12" Hines
PENETRATION WIDTH
FIRST BAR 2" CLEAR #3X @12" NEW 5" SLAB-ON- 2200 Ross Avenue, Suite 4200W
X AS REQ'D. SEE 1/S613-OF PROVIDE 6" EMBED
EDGE OF NEW FROM EXIST. OPENING, W/ 6" EMBED GRADE SEE S303-OF Dallas, TX 75201
PER 19/S613-OF
2 1/2"
(F.V.)
OPENING (972-716-2908 Corbin Eckel)
TYP. PER 19/S613-OF
EXISTING
NEW 5" SLAB-ON-GRADE 2800 Post Oak Blvd., 49th Floor
EXIST. FINISH SEE ARCH'L SLAB-ON-GRADE 3" TYP.
SEE S303-OF Houston, TX 77056
WATERSTOP ALL SLAB-N-GRADE (713-621-8000 Juan Delgado)
(F.V.)
6"
SIDES AT BELOW
EQ
EQ
GRADE INFILLS T.O.S.C. EL. T.O.S.C. EL. EQUITY PARTNERS
SEE PLAN T.O.S.C. EL. SEE PLAN McNair Interests
WATERPROOFING AS SEE PLAN 109 N. Post Oak Lane, Suite 600
5"
FIELD VERIFY
FIELD VERIFY
1" 1'-6" 1" REQUIRED, SEE Houston, TX 77024
(Drew Steffen)
ARCH'L
4" (F.V.) 1'-8" (F.V.) 1'-8" (F.V.) 1'-8" (F.V.) 4" (F.V.) VAPOR RETARDANT Mitsui Fudosan America
SEE SPECS 1251 Avenue of the Americas, Suite 800
4" (F.V.) 4" (F.V.) New York, New York 10020
VAPOR RETARDANT (David Leff)
SEE SPECS
FIELD 5G Studio Collaborative, LLC.
VERIFY Dallas, TX 75202
NEW OPENING IN EXISTING PAN JOIST FRAMING EXISTING CONC. WALL OPENING INFILL SLAB-GRADE-GRADE INFILL AT RECESS SLAB-GRADE-GRADE INFILL MASTER/MULTIFAMILY ARCHITECT
NEW OPENING IN EXISTING
1 TYPICAL DETAIL 2 TYPICAL DETAIL 3 TYPICAL DETAIL 4 TYPICAL DETAIL GFF Architects
N0 SCALE
NO SCALE NO SCALE NO SCALE NO SCALE 5 2808 Fairmount St., Suite 300
Dallas, TX 75201
12" CLR. TYP. WHERE CORES 48" CLR. TYP. WHERE CORES
ARE NOT ALIGNED IN ARE NOT ALIGNED IN
2" CLR. FROM
2" CLR. FROM

ZONING/ENTITLEMENT
(E) BEAMS
(E) BEAMS
DIRECTION OF SLAB SPAN DIRECTION OF SLAB SPAN NOTES:
Baldwin Associates
1. INSTALLATION MUST PRECISELY MATCH
MANUFACTURER'S INSTRUCTIONS. NOTE: Dallas, TX 75226
2. THROUGHLY CLEAN INSIDE OF PIPE INSTALLATION MUST PRECISELY MATCH (214-824-7949 Robert Baldwin)
PRIOR TO APPLYING BONDING AGENT MANUFACTURER'S INSTRUCTIONS.
(SIKA ARMATEC 110 EXPOCEM). REMOVE SECTION OF
SLAB BWTN. PENETRATIONS GEOTECH
ECS Southwest, LLP
CONCRETE JOIST BELOW Carrollton, TX 75006
SLAB SPAN
DIRECTION
SLAB SPAN
DIRECTION
"A"
12" CLR.
24" CLR.
CIVIL ENGINEER
TYP.
TYP.
BEAM OR JOIST BELOW Kimley-Horn and Associates, Inc.
EXISTING PENETRATION Dallas, TX 75240
ALIGN CORES IN SLAB
ALIGN CORES (972-770-1300 Alex Rathbun)
6" DIA. MAX. CORES. SCAN 10" DIA. MAX. CORES. SCAN CLEAR SPACING LESS THAN
LANDSCAPE ARCHITECT
SLAB FOR (E) REINF. & SLAB FOR (E) REINF. & OUTLINE OF SPALLING THE LARGER DIA. SWA Group
LOCATE CORES 1" CLEAR LOCATE CORES TO MINIMIZE THOROUGHLY CLEAN SPALLED SURFACE BELOW THE SLAB 2001 Irving Boulevard, Suite 157
W/ HIGH PRESSURE WATER BLAST, GRIND TOP EDGE Dallas, TX 75207
FROM (E) REINF. DO NOT CUT NUMBER OF BARS TO BE CUT. ALL AROUND
SCABBLER, OR OTHER APPROPRIATE (214-954-0016 Chuck McDaniel)
MAY CUT 2 BARS MAX.
1 1/8"
(E) REINF. SEE 7/S613-OF FOR FILL PIPE W/
MIN.
MECHANICAL MEANS TO OBTAIN & 1/4"
12" CLR. FROM CORES > 6" DIA. OR WHERE REMAIN 1" CLEAR FROM NON-SHRINK GROUT.
48" CLR. FROM
OTHER REINF. EXPOSED AGGREGATE SURFACE. COAT MIN STRUCTURAL
(E) OPENINGS REINF. CANNOT BE AVOIDED. (E) OPENINGS NOTIFY ENGINEER IF PIPE EXPOSED REINFORCEMENT W/ SIKA SEE __/____ FOR PENETRATION Datum Engineers
HAS SEVERED BEAM REINF. ARMATEC 110 EPOCEM. COAT EXPOSED & FILL-IN INFO. 6516 Forest Park Road
BEAM OR JOIST, SURFACE W/ SIKA ARMATEC 110 EPOCEM. SPALLED ZONE PROVIDE WELDED WIRE Dallas, TX 75235
BEAM OR JOIST, FILL PENETRATION W/ NON-SHRINK GROUT
SEE PLAN UNDERNEATH MESH OR "CHICKEN (214-358-0174 Rodolfo D'Arlach)
SEE PLAN AFTER CURING, FILL REMAINING VOIDS EXISTING SLAB WIRE" IF OPENING DIA.
W/ SIKA REPAIR SHB. IS GREATER THAN 8", MEP ENGINEER
CENTER WIRE IN SLAB. ME Engineers, Inc.
SECTION "A" 1825 Market Center Blvd., Suite 600
PLAN PLAN Dallas, TX 75207
CORES THRU (E) CAST-IN-PLACE CORES THRU (E) CAST-IN-PLACE
CONCRETE SLAB 6" DIA. OR LESS BEAM AND JOIST PENETRATION INFILL SLAB PENETRATION INFILL CLOSELY SPACED FLOOR PENETRATION INFILL
CONCRETE SLAB > 6" TO 10" DIA. ELEVATOR CONSULTANT
TYPICAL DETAIL 6 TYPICAL DETAIL 7 TYPICAL DETAIL 8 REPAIR DETAIL REPAIR DETAIL Persohn | Hahn Associates, Inc.
NO SCALE NO SCALE NO SCALE NO SCALE 9 NO SCALE 10 8612 Broad Meadow Lane

McKinney, TX 75071
INTERIOR DESIGNER
REMOVE ANY UNSOUND Rottet Studio
CONCRETE AROUND 808 Travis Street, Suite 100
PERIMETER OF OPENING, Houston, TX 77002
RETAIN EXISTING (713-221-1830 x 6105 Anja Majkic)
REINFORCING. CHIP ALL
AT (12A) #3@18" O.C. TYP. AROUND AT APPROX. 3 L5X3X3/8 LLV W/ 1/2" DIA.
ALL SIDES W/ 5" EMBED. PER VERTICAL TO 1 HORIZ. X 4" E.B. @ 18"
SAW CUT OPENING PER
19/S613-OF, ALSO PROVIDE SLOPE, CLEAN SURFACE & 1/2" DIA. EXP. 1/S613-OF . AFTER
WHEREVER 3:1 SLOPE FILL W/ SIKACRETE 211 & #3X3'-0" @ 1'-6"
BOLT W/ 2 1/2" INSTALLING CHANNELS,
CANNOT BE ACHIEVED USE SIKADUR 32 BONDING MAX. OPENING SIZE: SLAB ON DECK, SEE GENERAL W/ 8" EMBED www.datumengineers.com | Co. Reg. No. F-2819
REMOVE EXISTING SLAB EMBED. ONE AT CHIP EDGES & FILL PER SLAB ON DECK, Dallas Austin San Antonio
AGENT. AT CORRODED EA. ANGLE 5'-0" THIS WAY, 1'-8" PERP. AT DRAINS NOTES. SEE PLAN FOR DECK #3X3'-0" @ 1'-6"
214-358-0174 512-469-9490 210-858-2880
TO FORM 1" X SLAB DEPTH SEE GENERAL NOTES.
EXIST. SLAB REINFORCING, SEE S612-0F TO CHANNELS U.N.O. ORIENTATION W/ 8" EMBED. TYP. @ ALL SIDES 19/S613-OF Datum Project No. 19166
X CONT. KEY SHIM TIGHT & HAND PACK SEE PLAN FOR DECK
FOR CLEANING & COATING L3X3X1/4, TYP.
SLAB THICK.
EXIST. SLAB W/ ±1" OF NON-SHRINK ORIENTATION DATE ISSUE TITLE

EXISTING REINFORCING L5X5X3/8 @ (11A) 2" 19/S613-OF 04/03/2020 SCHEMATIC DESIGN PRESENTATION
PRIOR TO INFILLING. GROUT, TYP. AT 4 SIDES MAX. EXISTING BUILDING
> 3"
1" 1" (E) CONC. 2" TYP. SIM. 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
ALL SIDES OF OPENING FRAMING
CLR.
SLAB 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
2"
(F.V.)
1 1/2"
CLR.

1 1/2"
4"
CHANNEL FIREPROOF TO
MEET 2 HR. RATING
MIN.
SEE PLAN
6"

12GA. SHEET X AS REQ'D PROVIDE 3X3 W1.4XW1.4
EXISTING JOIST PROVIDE 3X3 W1.4XW1.4 W.W.M. TO FORM OPENING. 2'-0" MAX. W.W.M. WHERE OPENING CLEAR SPANS TO 10'-0" : #3
SLAB ON DECK AT SIM. IS ≥ 1'-0" 3/16 2
C6X8.2 CONT.
ALTERNATELY, MAY USE 4@(11A)
TYP. CLEAR SPANS TO 12'-0" : L5X5X5/16 X CONT.,
FORM BOTTOM OF SLAB TWO LAYERS OF 6X6 3/16 3 C7X9.8 1/4 FIREPROOF TO
BREAK AT INTERSECTING MEET 2 HR RATING
W1.4XW1.4 OFFSET AS CLEAR SPANS TO 16'-0" :
L3X3X1/4X0'-8" TYP. CHANNELS W/ 1" GAP IN
REQUIRED TO C9X13.4
W/2- 5/8" DIA. EXP. BOLTS BETWEEN
APPROXIMATE A 3X3
GRID. W/ 4" EMBED.
REINFORCING CHANNELS AT NEW EXISTING ELEVATOR, STAIR, OR EXISTING ELEVATOR, STAIR, OR
INFILL @ SLAB OPENINGS < 2'-0" SLAB OPENING 10" TO 20" MECHANICAL CHASE OPENING INFILL MECHANICAL CHASE OPENING INFILL
NO SCALE 11 TYPICAL DETAIL 12 ,12A TYPICAL DETAIL 13 TYPICAL DETAIL 14 TYPICAL DETAIL 15
NO SCALE NO SCALE NO SCALE NO SCALE
1 1/2" DEEP
DRILL HOLE 1/16" LARGER THAN THE .05 12/18/2020 Permit Set Update
POCKET MINIMUM
BAR DIA. CLEAN HOLE WITH CHIP OUT EXISTING
COMPRESSED AIR THEN WATER AND CONCRETE SURFACE
DRY THOROUGHLY PER MFR'S 1 1/2" DEEP MINIMUM
INSTRUCTIONS. FILL WITH SPECIFIED
ADHESIVE ANCHORING SYSTEM
NEW CONCRETE BEAM
15°
CLEAN CONCRETE SURFACE
OF ALL LAITANCE WITH WIRE
BRUSH AND WATER. WET
SURFACE IMMEDIATELY
SEE SECTIONS FOR DOWELS PRIOR TO PLACING
CONCRETE
8" .
. U.N.O
MIN
DRILL AND GROUT DOWELS,

EXISTING CONCRETE SEE 19/S613-OF AND
SECTIONS
1" DEEP SAWCUT AT
PERIMETER OF CONCRETE
IF THIS SIDE OF WALL IS NOT EXPOSED AND BEAM
IS ACCESSIBLE, HOLE MAY BE DRILLED MAPLE TERRACE
COMPLETELY THROUGH TO FACILITATE DO NOT CUT OR DAMAGE 3001 MAPLE AVENUE
CLEANING. TAPE OR SEAL TO CONTAIN EXISTING REINFORCING
ADHESIVE.
EXISTING WALL, BEAM,
OR COLUMN
RENOVATION DETAILS
SETTING DOWELS IN EXISTING CONCRETE
NEW CONCRETE BEAM TO EXISTING CONCRETE
TYPICAL DETAIL TYPICAL DETAIL
NO SCALE 19 NO SCALE
20 190013
PROJECT NUMBER
NOTE: E-0 E-0.4E-0.6
E-0.4 E-0.6 E1 E-1.1 E-1.2 E-1.3 E-1.4 E-1.5 E-1.6 E-1.7 E-1.8 E2 E-2.3 E-2.6
FIELD VERIFY LOCATIONS OF ALL EXISTING
16'-0 7/8" 5'-7 7/8" 14'-6 1/4" 12'-8 3/4" 22'-7 3/4" 19'-0" 15'-6" 14'-9 1/4" 15'-5 1/8" 18'-10" 22'-9 1/2" 12'-9 3/4" 15'-1 7/8" 21'-1 1/8"
ROOF COLUMNS SUPPORTING NEW
TERRACE FRAMING PRIOR TO 10 L3X3X1/4 HORIZ.
BRACE, SEE
S621-OF
FABRICATION. NOTIFY ENGINEER OF ANY 12/S622-OF, TYP.
1 2
COLUMN LOCATION DISCREPANCIES T.O. BEAM EL.
= 554'-0 3/4", TYP., U.N.O. S220-OF S621-OF
DEVELOPER
Hines
8"
E-A W12X16 W12X16 W12X16 W12X16 Dallas, TX 75201
6'-3 1/4"
7'-10 3/4"
1'-0"
5 2
9'-11" 12
W12X19
W12X19
W12X19
T.O. BEAM EL. = 552'-5 1/4"
13'-11 1/2"
W12X19
W12X19
W12X14 W12X19 W12X14 S623-OF S623-OF
W12X19
W12X19
W12X30
W12X30
HSS16X12X1/2 S621-OF Houston, TX 77056
12
2'-4" (713-621-8000 Juan Delgado)
2 3/8"
S621-OF
HSS16X12X1/2 HSS5X5X3/8
L3X3X1/4 HORIZ. EQUITY PARTNERS
W12X30 W12X30 W12X19 W12X19 W12X30 W12X30 TYP.
BRACE, SEE
E-B 12/S622-OF, TYP. 1/4" X 3" STRAP
McNair Interests
7/S622-OF
7/S622-OF
10'-10 3/4" (F.V.) 8'-8" (F.V.)

2 3/8"
(F.V.)
20/S621-OF HSS5X5X3/8, 109 N. Post Oak Lane, Suite 600
PLATE X-BRACE 1/4" X 3" STRAP
8'-9 3/4"
HSS5X5X3/8 , TYP. TYP. POST COL. 5'-8" 8" Houston, TX 77024
PLATE X-BRACE (Drew Steffen)
20/S621-OF
17/S621-OF
W18X65
17/S621-OF
W12X14 W12X14 W12X30 Mitsui Fudosan America
E-B.5 1251 Avenue of the Americas, Suite 800
W12X40
10'-10 3/4"
1 3/4"
1 3/4"
W12X40
W12X30
W12X30
W12X14
W12X30
10'-9"
11'-5" (David Leff)
1'-0"
1/S630-OF
W12X14
WB-1 8" OFFICE/RETAIL ARCHITECT
W 12X30
8"
E-C 1217 Main St., Suite 500
8"
EXISTING STAIR Dallas, TX 75202
SEE LEVEL 03 (S203-OF) 20/S621-OF
7'-1"
W12X30
1/4" X 3" STRAP 1/4" X 3" STRAP TOWER TO BE (214-347-4982 Christine Robbins-Elrod)
FOR ADDN'L INFO. NOT
14'-7 5/8"
SHOWN AT INFILL, TYP. EXISTING STAIR PLATE X-BRACE PLATE X-BRACE W 12X30 DEMO'D
A TOWER TO BE
8" EXISTING - 1/4" X 3" HORIZ.
DEMO'D GFF Architects
DATUM STRAP PLATE, TYP. 2808 Fairmount St., Suite 300
8 Dallas, TX 75201
S621-OF W12X30 W12X30 W12X14 1/4" X 3" STRAP (214-303-1500 Michael Reyes)
E-2
SW-3
15/S622-OF
19'-3"
PLATE X-BRACE
W12X14
W12X14
SW-1
ZONING/ENTITLEMENT
19
1'-8" (F.V.)
W12X14
Baldwin Associates
14'-8 5/8"
A8 1/4" X 3" STRAP S622-OF 3904 Elm Street, Suite B

PLATE X-BRACE 1/4" X 3" STRAP Dallas, TX 75226
PLATE X-BRACE (214-824-7949 Robert Baldwin)
B W 1 2 X3 0 W12X30
W12X30 GEOTECH
E-4 SW-2 ECS Southwest, LLP
L3X3X1/4 HORIZ. BRACE 3033 Kellyway Drive, Suite 110
20/S621-OF
W12X14
W12X14
T.O. BEAM EL. (972-392-3222 Siddharth Neekhra)
16
W12X14
= 554'-0 3/4", TYP., U.N.O.
S622-OF
19'-0"
CIVIL ENGINEER
30'-7 1/4"
8" 1'-0" L3X3X1/4 HORIZ.

BRACE, TYP. Kimley-Horn and Associates, Inc.
L3X3X1/4 HORIZ. 13455 Noel Road, Two Galleria Office Tower, Suite 700
8"
BRACE, SEE Dallas, TX 75240
1'-0" 12/S622-OF, TYP. (972-770-1300 Alex Rathbun)
W12X30 W12X30
E-7 W12X30 5
LANDSCAPE ARCHITECT
T.O. BEAM EL. HSS5X5X3/8, S621-OF
HSS5X5X3/8, SWA Group
= 554'-0 3/4", TYP., U.N.O. TYP. POST COL. 2001 Irving Boulevard, Suite 157
14'-4 3/4"
20/S621-OF TYP. POST COL. Dallas, TX 75207

20/S621-OF
C (214-954-0016 Chuck McDaniel)
5'-9 3/4"
STRUCTURAL
E-D Datum Engineers
6" Dallas, TX 75235
6'-4" 9'-7 1/2" 14'-0 1/2" 5'-8" 23'-10" 6" 18'-10" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" 6'-4" (214-358-0174 Rodolfo D'Arlach)
2'-2" 30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4" MEP ENGINEER

ME Engineers, Inc.
Dallas, TX 75207
E1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 E2
ELEVATOR CONSULTANT
1 LEVEL 08 - LOW PLATFORM FRAMING McKinney, TX 75071
3/32" = 1'-0"
INTERIOR DESIGNER
Rottet Studio
E-0 E-0.4E-0.6
E-0.4 E-0.6 E1 E-1.1 E-1.2 E-1.3 E-1.4 E-1.5 E-1.6 E-1.7 E-1.8 E2 E-2.3 E-2.6 808 Travis Street, Suite 100
Houston, TX 77002
16'-0 7/8" 5'-7 7/8" 14'-6 1/4" 12'-8 3/4" 22'-7 3/4" 19'-0" 15'-6" 14'-9 1/4" 15'-5 1/8" 18'-10" 22'-9 1/2" 12'-9 3/4" 15'-1 7/8" 21'-1 1/8" (713-221-1830 x 6105 Anja Majkic)
10 1 2 10
T.O. BEAM EL. = 556'-2", TYP.
6'-3 1/4"
PROVIDE 5 - 2X10 AT 6" O.C. S621-OF PROVIDE 5 - 2X10 AT 6" O.C.
S220-OF S621-OF S621-OF
UNDER PLANTER T.O. DECK EL. = 557'-2" UNDER PLANTER
L3X3X1/4 HORIZ. BRACE, TYP.
E-A 2-2X8 AT 18" TO MATCH
4" www.datumengineers.com | Co. Reg. No. F-2819
2 4" 1/4" X 3" STRAP PLATE X-BRACE 5 2 Dallas Austin San Antonio
PAVER JOINT LOCATIONS. S623-OF 12
6'-1 1/4"
4"
13'-11 1/2"
214-358-0174 512-469-9490 210-858-2880
4"
13'-11 1/2"
PROVIDE 5 - 2X10 AT 6" O.C. COORDINATE WITH W12X14 W12X16 W12X16 W12X16 W12X14 S623-OF S623-OF
4"
S621-OF Datum Project No. 19166
4"
UNDER PLANTER W12X14 W12X14

LANDSCAPE
W12X16
9
W12X45
DATE ISSUE TITLE

W12X14
W12X14
12
6'-1 1/4"
9
2 3/8"
(F.V.)
W12X16
7'-6"
2-2X8 AT 18" TO MATCH
2 3/8"
(F.V.)
S623-OF PROVIDE 5 - 2X10 AT 6" O.C. 04/03/2020 SCHEMATIC DESIGN PRESENTATION

S621-OF 5/4 IPE DECK S623-OF PAVER JOINT LOCATIONS.
.016 W12X16 W12X16 W12X16 W12X16 W12X16 W12X16 W12X16 UNDER PLANTER 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
COORDINATE WITH
E-B 4'-0" L3X3X1/4 HORIZ. 8 7 LANDSCAPE 6'-4" 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
W12X16
4" TYP.
2x10 @ 16"
5/S622-OF 5/S622-OF
W12X26
7/S622-OF
W12X26
8'-9 3/4"
BRACE, TYP.
4" TYP.
S623-OF S623-OF
7/S622-OF
8 4" TYP.
8'-8"
17/S622-OF
W12X40
W12X30
W12X30
W12X40
W12X45
4"
TYP. 7 S623-OF 12/18/2020 90% CONSTRUCTION DOCUMENTS

4"
W12X16 W12X16 W12X16 W12X26 S623-OF W12X26 W12X16 W12X16 W12X16 01/25/2021 100% CONSTRUCTION DOCUMENTS
E-B.5 W12X26 W12X16 W12X16 W12X16 W12X16
1 3/4"
4'-0"
4'-0"
1 3/4"
.016 W12X26
9'-6 5/8"
W12X26
W12X16
W12X26 W12X16
2x10 @ 16"
W12X16
W12X16 W12X26
W12X16
W12X26 W12X16 W12X26

2x10 @ 16"
W12X26
17/S621-OF
17/S621-OF
.016
W 12X
20/S622-OF
W12X30
11'-5"
11'-5"
18/S622-OF
9'-9"
W12X30
TYP.
TYP.
16
T.O. BEAM EL. = 556'-2", TYP. W 12X26 W 12X30 W12X16 W12X26 W12X16 W12X16 W12X16 W12X16 W12X16 W12X26 W12X16 W12X16 W12X26
E-C
W12X14
W12X14
4'-0"
3" E.J.
W12X16
1'-0"
7'-1"
17/S622-OF L3X3X1/4 HORIZ. BRACE, TYP. L3X3X1/4 HORIZ. BRACE, TYP.

W12X16
W12X16
T.O. DECK EL. = 557'-2" 4" .016

W12X16
TYP.
16'-6"
14'-7 5/8"
W 12X30
A T.O. DECK EL. = 557'-2"
1'-3"
PROVIDE STIFFENER
PROVIDE 2X BLOCKING AT PER DETAIL 8/S623-OF
8 MIDSPAN ON ALL MEMBERS AT GATE VERTICAL
W12X26
W12X26
S621-OF W12X30 T.O.S.C. EL. = 557'-2" GREATER THAN 8 FEET LONG.
E-2 POST
15/S622-OF
19'-3"
20/S622-OF
SW-3
STAIR 1
W12X26
L3X3X1/4 HORIZ.
SW-1
TYP. .016
L3X3X1/4 HORIZ. STAIR 2 BRACE, TYP.
W12X16
W12X16
14'-8 5/8"
BRACE, TYP.
W12X16
A8
W12X16

18/S622-OF 18/S622-OF .05 12/18/2020 Permit Set Update
TYP. .016 05/03/2021 ADDENDUM 08
B TYP. W12X30
5"
W12X30
SW-2
E-4 17/S622-OF
TYP. 3" E.J.
3" E.J.
2x10 @ 16" T.O. BEAM EL. = 556'-2", TYP.
W12X30
W12X26
W12X30
W12X26
W12X30
W12X30
T.O. BEAM EL. = 557'-2"

19'-0"
W12X30
5/4 IPE DECK
30'-7 1/4"
6'-2" 15/S623-OF
4'-0"
W12X16 W12X16
E-7 W12X30 5
W12X16
W12X14
6'-0"
S621-OF
5'-0"
4"
14'-4 3/4"
W12X16 W12X16 W12X16
4"
C PROVIDE 5 - 2X10 AT 6" O.C. 4'-0" 4" .016
UNDER PLANTER 9 6'-4"
9
S623-OF
E-D S623-OF
9'-11" 6'-4" 9'-7 1/2" 14'-0 1/2" 29'-6" 6" 30'-0" 19'-4" 10'-8" 14'-0 1/2" 9'-7 1/2" 6'-4" 13'-8"
PROVIDE 5 - 2X10 AT 6" O.C.
13'-8" 30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4" UNDER PLANTER
00 E1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 E2 15 MAPLE TERRACE
3001 MAPLE AVENUE
EXISTING ROOF/TERRACE
2 LEVEL 08 - HIGH PLATFORM FRAMING FRAMING AND DETAILS
3/32" = 1'-0"
190013
PROJECT NUMBER
SEE PLAN
NOTES:
1. ALL TERRACE STEEL NOTE:
TO BE GALVANIZED. KICKER PER 10/S623-OF FUTURE PLANTER, SEE SEE 2/S621-OF FOR
CURTAIN WALL AT EACH HANDRAIL HAND RAIL CURTAIN WALL LANSCAPE
2. PAINT ALL FIELD SEE ARCH'L INFO. NOT SHOWN.
WELDS WITH GALV. VERTICAL ANGLE SEE ARCH'L (335# PLF MAX.)
2X WOOD PURLIN SLAB 4"
COMPOUND AFTER E.J. SEE PLAN SEE PLAN E.J. EPA DECK SEE PLAN
WELDING IS COMPLETED SEE PLAN 2X BLOCKING TYP. T.O. BEAM EL. EXIST. PARAPET
SEE PLAN
IPE DECK SEE PLAN T.O. BEAM EL. TO REMAIN
NEW CONSTRUCTION HSS POST, (GALV.)
FINISH T.O.S.C. EL.
T.O.S.C. EL. FINISH
SEE ARCH'L SEE PLAN DEVELOPER
SEE PLAN SEE ARCH'L
EXIST. PARAPET Hines
6/S623-OF TO REMAIN SEE 2200 Ross Avenue, Suite 4200W
EXIST. PARAPET SEE PLAN PLAN Dallas, TX 75201
TO BE DEMO'D (972-716-2908 Corbin Eckel)
SEE PLAN A/S640-OF SEE PLAN 20/S621-OF
20/S621-OF 2800 Post Oak Blvd., 49th Floor
T.O. BEAM EL. Houston, TX 77056
18/S621-OF HORIZ. X-BRACE T.O. BEAM EL. SEE PLAN (713-621-8000 Juan Delgado)
BEAM (HIGH)
SEE PLAN SEE PLAN
19/S621-OF (GALV.) SEE PLAN
SEE PLAN
EQUITY PARTNERS
SCAN AND LOCATE STRAP PLATE
McNair Interests
EXIST REINF. SEE SEE PLAN
4'-0"
NOTE 7 AND 8 ON Houston, TX 77024
FIELD DRILLED WATERPROOFING
J/S640-OF BEAM (LOW) DEMO PORTION OF (Drew Steffen)
ANCHOR NOTES ON AND INSULATION 18/S621-OF KICKER PER 10/S623-OF
SEE ARCH'L (GALV.) SEE PLAN PARAPET AS 1
S102-OF 1 Mitsui Fudosan America
NEEDED TO 2 1 1251 Avenue of the Americas, Suite 800
2 KICKER PER 10/S623-OF INSTALL NEW POST T.O.S.C. EL. 2
T.O.S.C. EL. New York, New York 10020
SEE PLAN 13/S621-OF SEE PLAN (David Leff)
6" +/-
6" +/-
PL.1/2X14X0'-10" W/2-3/4"
PL.1/2X14X0'-10" W/2-3/4" SCAN AND LOCATE OFFICE/RETAIL ARCHITECT
DIA. X 6" HAS-V-36 W/
3" +/-
HILTI-HIT-RE 500V3 .016 EXIST. ROOF FRAMING DIA. X 6" HAS-V-36 W/ EXIST REINF. SEE CLOSURE STUD FRAMING EXIST. ROOF FRAMING SEE 17/S623-OF 2/S621-OF 5G Studio Collaborative, LLC.
3" +/-
PL.1/2X14X0'-10" W/4-3/4" HILTI-HIT-RE 500V3 .016 NOTE 7 AND 8 ON SEE ARCH'L FOR TEMPORARY 1217 Main St., Suite 500
W/ 1/2" N.S. GROUT PL.1/2X14X0'-10" W/4-3/4" Dallas, TX 75202
DIA. X 6" HAS-V-36 W/ W/ 1/2" N.S. GROUT FIELD DRILLED FRAMING
1/2" EXIST. COLUMN DIA. X 6" HAS-V-36 W/ .016 (214-347-4982 Christine Robbins-Elrod)
ANCHOR NOTES ON
2" +/-
HILTI-HIT-RE 500V3 EXIST. COLUMN

1'-2"
1/2" HILTI-HIT-RE 500V3
2" +/-
S102-OF
1'-2"
W/ 1/2" N.S. GROUT W/ 1/2" N.S. GROUT
.016
6" +/-
2 5
2" +/-
3" +/- GFF Architects

6" +/-
3" +/-
.016 5" +/-
2" +/-
3" +/- 1/2" = 1'-0" 1/2" = 1'-0"
3" +/-
5" +/- 2808 Fairmount St., Suite 300

Dallas, TX 75201
ZONING/ENTITLEMENT
NOTE: Baldwin Associates
SEE 5/S621-OF FOR 3904 Elm Street, Suite B
Dallas, TX 75226
INFO. NOT SHOWN. NOTE: (214-824-7949 Robert Baldwin)
SEE PLAN SEE PLAN SEE 2/S621-OF FOR
SEE PLAN
CURTAIN WALL CURTAIN WALL INFO. NOT SHOWN. GEOTECH
SEE PLAN SEE PLAN
SEE ARCH'L ECS Southwest, LLP
E.J. CANOPY COLUMN
E.J. 3033 Kellyway Drive, Suite 110
SEE PLAN SEE PLAN Carrollton, TX 75006
SEE PLAN HAND RAIL
SEE ARCH'L
NEW CONSTRUCTION IPE DECK
T.O.S.C. EL. 6/S623-OF CIVIL ENGINEER
SEE PLAN EXIST. PARAPET T.O.S.C. EL. Kimley-Horn and Associates, Inc.
TO REMAIN SEE PLAN 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
EXIST. PARAPET EXIST. PARAPET (972-770-1300 Alex Rathbun)
TO BE DEMO'D SEE PLAN SEE PLAN EXIST. PARAPET TO REMAIN
SEE PLAN
SEE PLAN TO BE DEMO'D SEE PLAN LANDSCAPE ARCHITECT
SWA Group
Dallas, TX 75207
STRUCTURAL
Datum Engineers
Dallas, TX 75235
KICKER PER 10/S623-OF 3/S622-OF (214-358-0174 Rodolfo D'Arlach)
1
2
T.O.S.C. EL. MEP ENGINEER
SEE PLAN T.O.S.C. EL. ME Engineers, Inc.
SEE PLAN 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
EXIST. ROOF FRAMING SEE 17/S623-OF (214-741-1589 Drew Shivley)
FOR TEMPORARY EXIST. ROOF FRAMING
EXIST. COLUMN
EXIST. COLUMN FRAMING ELEVATOR CONSULTANT
.016 Persohn | Hahn Associates, Inc.
EXIST. COLUMN 8612 Broad Meadow Lane
McKinney, TX 75071

1/2" = 1'-0" 8 Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)
NOTE: 11
SEE 5/S621-OF FOR
SEE PLAN INFO. NOT SHOWN. S623-OF
SEE PLAN WEB STIFFENER 3/4" DIA. BOLT, TYP.

SEE PLAN
PLATE, TYP.
T.O.S.C. EL. POCKET EXISTING www.datumengineers.com | Co. Reg. No. F-2819
SEE PLAN PARAPET TO INSTALL 214-358-0174 512-469-9490 210-858-2880
NEW BEAM NOTE: Datum Project No. 19166
STIFFENER PLATE SHALL BE EQUAL IN THICKNESS TO THE COLUMN DATE ISSUE TITLE
T.O. BEAM EL. WALL THICKNESS OR BEAM THICKNESS, WHICHEVER IS GREATER. 04/03/2020 SCHEMATIC DESIGN PRESENTATION
SEE PLAN
2" MIN.
SEE PLAN 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
18/S621-OF FOUR HOLES ARE PERMISSIBLE 1/4
BEAM (HIGH) EXISTING ROOF A/S640-OF HIGH COLUMN IN THE CAP PLATE. ONLY TWO 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
(GALV.) SEE PLAN 1/2" CAP PLATE 10/30/2020 ISSUE FOR PERMIT
HOLES ARE PERMISSIBLE IN THE 2-3/4" DIA. BOLTS,
BEAM FLANGE. STAGGERED ON EACH
2/S621-OF PLAN VIEW 01/25/2021 100% CONSTRUCTION DOCUMENTS
BOTTOM FLANGE OF BEAM. COLUMN, SEE SIDE OF BEAM WEB
BEAM (LOW) B.P. LOW SCHEDULE
(GALV.) SEE PLAN STIFF PL.
STIFF PL. OR PLAN
1/2" BASE PLATE RESERVED FOR REVIEWERS NOTES
CENTERED ON
PLAN - BEAM/COLUMN CONNECTION DETAIL
COLUMN AND BEAM
3"
DEMO PORTION OF PARAPET NO SCALE

2" MIN.
T.O.S.C. EL. AS NEEDED TO INSTALL NEW

8" MIN.
SEE PLAN BEAM LOW POST STIFFENER

BOTTOM CHORD PLATE EACH
SEE PLAN SIDE
EXIST. ROOF FRAMING SEE 17/S623-OF
FOR TEMPORARY
EXIST. COLUMN FRAMING GROUT POCKET
.016 4" +/- SEE PLAN FOR BEAM
3" 1/16" SMALLER
1/2" = 1'-0" 12 1" = 1'-0" 13 3/16

THAN BEAM
WEB
NOTES: THICKNESS,
3/16" MIN. REV. DATE ISSUE TITLE
1. SEE ROOF PLAN FOR ROOF SLOPE. SLOPE CAP PLATES ACCORDINGLY. .05 12/18/2020 Permit Set Update
NOTE: NOTES: BASE PLATE - BOLTED CONNECTION
2. STIFFENER PLATE SHALL BE EQUAL IN THICKNESS TO THE COLUMN WALL .016 05/03/2021 ADDENDUM 08
ALL TERRACE STEEL 1. SEE ROOF PLAN FOR ROOF SLOPE. SLOPE CAP PLATES
THICKNESS OR BEAM WEB THICKNESS, WHICHEVER IS GREATER.
TO BE GALVANIZED. ACCORDINGLY.
CURTAIN WALL 3. CONNECT INTERSECTING BEAMS TO STIFFENER PLATES USING BOLTS IN
2. STIFFENER PLATE SHALL BE EQUAL IN THICKNESS TO THE COLUMN
SEE ARCH'L SINGLE SHEAR DESIGNED FOR ECCENTRIC BEAM REACTION.
WALL THICKNESS OR BEAM WEB THICKNESS, WHICHEVER IS
2X WOOD PURLIN
E.J. GREATER.
SEE PLAN
SEE PLAN 3. CONNECT INTERSECTING BEAMS TO STIFFENER PLATES USING BOLTS
IN SINGLE SHEAR DESIGNED FOR ECCENTRIC BEAM REACTION.
IPE DECK L3X3 X-BRACE 2X BLOCKING
SEE PLAN SEE PLAN TYP. 1/16" SMALLER
THAN BEAM
T.O.S.C. EL. WEB
STIFFENER
SEE PLAN 1/16" SMALLER THICKNESS,
PLATE EACH SIDE
THAN BEAM 3/16" MIN.
WEB 3/4" DIA. BOLT, TYP.
THICKNESS,
3/16"
STIFFENER MINIMUM
PLATE EACH SIDE 2-3/4" DIA. BOLTS,
BEAM (HIGH) STAGGERED ON EACH
A/S640-OF 2-3/4" DIA. BOLTS SIDE OF BEAM WEB
18/S621-OF (GALV.) SEE PLAN
19/S621-OF
2" MIN. COLUMN FOUR HOLES ARE
TYP. WATERPROOFING COLUMN, SEE CAP PLATE PERMISSIBLE IN THE CAP
AND INSULATION SCHEDULE SEE PLAN FOR BEAM 3" PLATE. ONLY TWO HOLES
SEE ARCH'L SEE PLAN FOR BEAM ARE PERMISSIBLE IN THE
OR PLAN TYP
TYP. J/S640-OF BEAM (LOW) 3" PLAN VIEW BEAM FLANGE.
1/2" CAP PLATE CENTERED
3/16 (GALV.) SEE PLAN COLUMN, SEE 1/2" CAP PLATE
TYP ON COLUMN AND
SCHEDULE OR CENTERED ON COLUMN
BOTTOM FLANGE
T.O.S.C. EL. PLAN AND BEAM
1/4 OF BEAM.
SEE PLAN
6" MAX.
MAPLE TERRACE
TYP.
1/4 PLAN - BEAM/COLUMN CONNECTION DETAIL

3001 MAPLE AVENUE
STRAP PLATE NO SCALE
STRAP PLATE DALLAS, TEXAS, 75201
SEE PLAN EXIST. ROOF
SEE PLAN
FRAMING TERRACE SECTIONS AND
HSS POST, (GALV.) CAP PLATE - BOLTED CONNECTION
SEE PLAN CAP PLATE - BOLTED CONNECTION DETAILS
EXIST. COLUMN
TYPICAL DETAIL TYPICAL DETAIL TYPICAL DETAIL
1/2" = 1'-0" 17 NO SCALE 18 NO SCALE
19 NO SCALE
20 190013
PROJECT NUMBER
NOTE:
SEE 3/S622-OF FOR
E-B COLUMN
COLUMN
4
BASE PL. 24" X 24" X 1" JS640-OF SEE PLAN
S622-OF W/4-3/4" DIA. X 12" COLUMN
ANCHOR BOLTS SEE PLAN
BEAM 1" N.S. GROUT
SEE PLAN W.P. BEAM DEVELOPER
K/S640-OF SEE PLAN
EXISTING ROOF FRAMING EXISTING ROOF Hines
SEE PLAN 2" 2" FRAMING 2" 2" 2200 Ross Avenue, Suite 4200W
4"
Dallas, TX 75201
SEE PLAN FV LOCATION OF JOISTS
PRIOR TO FABRICATION
Houston, TX 77056
4"
6" (F.V)
2 1/2" (F.V)
2"
1'-6" (F.V)
CHANNEL EQUITY PARTNERS
M
1/4 PL.3/8"
IN
.
NOTE: 2#5 BOT. BARS LENTON COUPLER 109 N. Post Oak Lane, Suite 600
ALL TRELLIS STEEL TO BE PAINTED EA. SIDE 1/4 Houston, TX 77024
WITH RUST INHIBITOR EXTERIOR PAINT, (Drew Steffen)
2#5 X EA. SIDE
4"
SEE ARCH'L
LENTON COUPLER 1251 Avenue of the Americas, Suite 800
1" DEEP X 6" KEY INTO New York, New York 10020
3'-0"X3'-0" BENT CAP EXISTING BEAM (David Leff)
DRILL THRU EXISTING BEAM COPE BOTTOM LEG OF
CENTERED ON EXISTING
EXISTING COLUMN AND EPOXY DOWL ANGLE AS REQ'D FOR
COLUMN WITH 5000 PSI OFFICE/RETAIL ARCHITECT
DRILL THRU EXISTING BEAM SEE PLAN CONNECTION
CONC. MIX. 5G Studio Collaborative, LLC.
AND EPOXY 8#5 HOOKED ANGLE, HORIZONTAL 1217 Main St., Suite 500
EXISTING CONC. BEAM DOWELS. DO NOT DAMAGE BRACE, SEE PLAN Dallas, TX 75202
COLUMN TO ALIGN WITH C.L. COLUMN SEE PLAN EXISTING BEAM REINF. BEAM (214-347-4982 Christine Robbins-Elrod)
OF EXISTING COLUMN SEE PLAN SEE PLAN
PLAN
EXISTING COLUMN MASTER/MULTIFAMILY ARCHITECT
SEE PLAN
1" = 1'-0" 3 1" = 1'-0" 4 1" = 1'-0" 5
GFF Architects
Dallas, TX 75201
TENEMEC
ZONING/ENTITLEMENT
GALVANIZE TERRACE FRAMING
Baldwin Associates
BOTTOM PORTION SEE PLAN
OF COLUMN GRIND BEAM Dallas, TX 75226
7'-0" 7'-0"
SMOOTH 1/4 SEE PLAN (214-824-7949 Robert Baldwin)
LEVEL 08
557'-2"
6"
T.O.S. EL.
GEOTECH
GALV.
BEAM Carrollton, TX 75006

SEE PLAN
END CAP TO CIVIL ENGINEER

MATCH BEAM Kimley-Horn and Associates, Inc.
WALL THICKNESS 13455 Noel Road, Two Galleria Office Tower, Suite 700
Dallas, TX 75240
CHANNEL CHANNEL CHANNEL (972-770-1300 Alex Rathbun)
SEE PLAN SEE PLAN 1/4
SEE PLAN
LANDSCAPE ARCHITECT
EXISTING ROOF FRAMING SWA Group
SEE PLAN GRIND 2001 Irving Boulevard, Suite 157
SMOOTH 5/16 Dallas, TX 75207
EXIST. ROOF CHANNEL
551'-2" SEE PLAN
CHANNEL STRUCTURAL
COLUMN SEE PLAN
CHANNEL TO Datum Engineers
W6 TO TUBE, SEE PLAN W6 BETWEN 6516 Forest Park Road
GRIND SMOOTH, TUBE, GRIND GRIND SMOOTH
SMOOTH 1/4 3/16 3-12 GRIND SMOOTH 1/4 CHANNELS Dallas, TX 75235
3/16 TYP
EXISTING COLUMN WOOD SLATS BEYOND (214-358-0174 Rodolfo D'Arlach)
W6 TO
SEE PLAN CHANNEL, SEE ARCH'L
3/S622-OF 3/16 MEP ENGINEER
GRIND SMOOTH
ME Engineers, Inc.
W6X9 BETWEEN CHANNELS 1825 Market Center Blvd., Suite 600
Dallas, TX 75207
ELEVATOR CONSULTANT
1/2" = 1'-0" 7 1" = 1'-0" 9 1" = 1'-0" 10 Persohn | Hahn Associates, Inc.
McKinney, TX 75071
BEAM (LOW) NOTE:
SEE PLAN NOTE: NOTE: PAINT ALL FIELD WELDS WITH GALV. INTERIOR DESIGNER
SEE 2/S621-OF FOR A/S640-OF
SEE 2/S621-OF FOR COMPOUND AFTER WELDING IS Rottet Studio
SEE PLAN INFO. NOT SHOWN. TYP. INFO. NOT SHOWN. COMPLETED 808 Travis Street, Suite 100
19/S621-OF
ANGLE BRACING SEE PLAN Houston, TX 77002
SEE PLAN
TYP. LEVEL 08 (713-221-1830 x 6105 Anja Majkic)
SEE PLAN SEE PLAN
SEE PLAN 557'-2"
3 SIDES, TYP. 19/S621-OF COLUMN
3/16 2" MIN.
SEE PLAN
20/S621-OF 20/S621-OF
NOTE: Dallas Austin San Antonio
SEE 2/S621-OF FOR 214-358-0174 512-469-9490 210-858-2880
INFO. NOT SHOWN. Datum Project No. 19166

DATE ISSUE TITLE
W.P.
3" MAX.
BEAM (HIGH) 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
TYP.
1/4 (GALV.) SEE PLAN 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
W.P. 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
ANGLE BRACE 18/S621-OF COLUMN
8" MAX. BEAM (LOW)
SEE PLAN SEE PLAN 12/18/2020 90% CONSTRUCTION DOCUMENTS
BEAM LOW SEE PLAN
SEE PLAN
COLUMN
SEE PLAN COLUMN TYP.
1 SEE PLAN 1/4 RESERVED FOR REVIEWERS NOTES
1 W.P. 2" MIN.
3" MAX.
TYP.
BEAM (LOW)
STRAP PL. (GALV.) SEE PLAN
SEE PLAN
EXIST. ROOF
551'-2"
ELEVATION
PLAN ELEVATION 1" = 1'-0" 12 3/4" = 1'-0" 15

6" MAX. .05 12/18/2020 Permit Set Update
3 SIDES, TYP.
1/4 2" MIN.
20/S621-OF
TYP. 20/S621-OF SEE PLAN SEE PLAN
2"
M
17/S622-OF
IN
TYP. BEAM
.
1/4
TYP. SEE PLAN
ANGLE HORIZ. BRACE, W.P. W.P.
SEE 12/S622-OF BEAM LOW
SEE PLAN 1/4
BEAM
TYP. SEE PLAN
18/S622-OF 1/4 W.P.
STRAP PLATE
X-BRACE, SEE PLAN COPE BOTTOM LEG OF
AND 15/S622-OF COPE BOTTOM LEG OF ANGLE, HORIZONTAL BRACE ANGLE AS REQ'D FOR ANGLE, HORIZONTAL BRACE
ANGLE AS REQ'D FOR SEE PLAN CONNECTION SEE PLAN
CONNECTION STRAP PLATES
STRAP PLATE SEE PLAN
X-BRACE, SEE PLAN BLOCKING COPE BOTTOM LEG OF
AND 15/S622-OF SEE PLAN ANGLE AS REQ'D FOR
ANGLE HORIZ. BRACE, CONNECTION
SEE PLAN BEAM
SEE PLAN
ANGLE, HORIZONTAL BRACE
W.P. SEE PLAN
6" MAX. MAPLE TERRACE

TYP. 3001 MAPLE AVENUE
ANGLE HORIZ. BRACE, DALLAS, TEXAS, 75201
SEE 12/S622-OF
PLAN 20/S621-OF
SEE PLAN
PLAN
TERRACE SECTIONS AND
PLAN
DETAILS
1/4" = 1'-0" 16 1" = 1'-0" 17 1" = 1'-0" 18 PLAN

1/2" = 1'-0" 19 1" = 1'-0" 20 190013 S622-OF
PLANTER,
SEE LANSCAPE
CURTAIN WALL PAVER SYSTEM CURTAIN WALL PAVER SYSTEM
SEE ARCH'L SEE LANDSCAPE SEE ARCH'L SEE LANDSCAPE
2X WOOD PURLIN HAND RAIL 2X WOOD PURLIN HAND RAIL
E.J. SEE PLAN SEE ARCH'L E.J. SEE PLAN SEE ARCH'L
4"
SEE PLAN 2X WOOD PURLIN SEE PLAN 2X WOOD PURLIN
NEW CONSTRUCTION IPE DECK SEE PLAN NEW CONSTRUCTION IPE DECK SEE PLAN
NOTCH
NOTCH
NOTCH
NOTCH
SEE PLAN SEE PLAN
3/4"
3/4"
DEVELOPER
3/4"
3/4"
4"
T.O.S.C. EL. Hines
SEE PLAN 2200 Ross Avenue, Suite 4200W
Dallas, TX 75201
SEE PLAN SEE PLAN 2800 Post Oak Blvd., 49th Floor
Houston, TX 77056
6/S623-OF 6/S623-OF (713-621-8000 Juan Delgado)
EQUITY PARTNERS
KICKER PER 10/S623-OF KICKER PER 10/S623-OF McNair Interests
SEE PLAN AT EACH VERTICAL ANGLE SEE PLAN AT EACH VERTICAL ANGLE 109 N. Post Oak Lane, Suite 600
Houston, TX 77024
SEE PLAN SEE PLAN (Drew Steffen)

(David Leff)
Dallas, TX 75202
1/2" = 1'-0" 2 1/2" = 1'-0" 5 GFF Architects
Dallas, TX 75201
ZONING/ENTITLEMENT
TYP. Baldwin Associates
3/16 3904 Elm Street, Suite B
SEE 5/S621-OF FOR (214-824-7949 Robert Baldwin)
NOTE: INFO. NOT SHOWN.
PLANTER, SEE 5/S621-OF FOR GEOTECH
PLANTER, PL.3/8", TYP. ECS Southwest, LLP
SEE LANSCAPE INFO. NOT SHOWN. PAVER SYSTEM. SEE PLAN
SEE PLAN SEE LANSCAPE 3033 Kellyway Drive, Suite 110
HAND RAIL COORDINATE PURLIN
"L" Carrollton, TX 75006
SEE ARCH'L SPACING WITH PAVER TYP. (972-392-3222 Siddharth Neekhra)
SUPPORT LOCATIONS 3/16
SEE PLAN 4" SEE LANDSCAPE SEE PLAN
ADDN'L 2X10 @ EDGE CIVIL ENGINEER
L3X3X3/8 X CONT. SEE PLAN "L"<9'-0" = L3x3x1/4
SEE ARCH'L EPA DECK 2X WOOD PURLIN HAND RAIL 9'-0"<"L"<13'-0" = L4x4x1/4
2X WOOD PURLIN EPA DECK 13455 Noel Road, Two Galleria Office Tower, Suite 700
SEE PLAN SEE PLAN SEE ARCH'L SEE PLAN Dallas, TX 75240
L3X3X1/4 @ 36" MAX. SEE PLAN
4"
FINISH (972-770-1300 Alex Rathbun)
COORDINATE WITH TRIM 3/4" FROM 2-2X AT TYP.
SEE ARCH'L 3/16
HANDRAIL VERTICAL POST PERIMETER TO MATCH LANDSCAPE ARCHITECT
T.O. WOOD EL. SWA Group
T.O. BEAM EL
T.O. BEAM EL. 2001 Irving Boulevard, Suite 157
TYP.
SEE PLAN
SEE PLAN 6" 6" 6" 6" Dallas, TX 75207
3/16 2 (214-954-0016 Chuck McDaniel)
1/4" STIFF. PLATES
6/S623-OF 2 1/2" PL.3/8", TYP.
AT EACH HANDRAIL
6" 6" 6" 6" 6" BEAM SUPPORT 2X WOOD PURLIN STRUCTURAL
KICKER PER 10/S623-OF SEE PLAN SEE PLAN Datum Engineers
AT EACH VERTICAL ANGLE L3X3X1/4 AT EACH 2 1/2" "
VERTICAL ANGLE BEAM "L TYP. 6516 Forest Park Road
3/16 Dallas, TX 75235
SEE PLAN BEAM (214-358-0174 Rodolfo D'Arlach)
SEE PLAN
"L"<9'-0" = L3x3x1/4 MEP ENGINEER
9'-0"<"L"<13'-0" = L4x4x1/4 ME Engineers, Inc.
Dallas, TX 75207
STEEL BEAM BOTTOM FLANGE BRACING

ELEVATOR CONSULTANT
TO PARALLEL BEAM OR JOIST
TYPICAL DETAIL 8612 Broad Meadow Lane

McKinney, TX 75071
NO SCALE
1/2" = 1'-0" 6 1/2" = 1'-0" 7 1/2" = 1'-0" 8 1/2" = 1'-0" 9 10 INTERIOR DESIGNER
Rottet Studio
Houston, TX 77002
STRAP PLATE TO HAVE MINIMUM (713-221-1830 x 6105 Anja Majkic)
CROSS-SECTIONAL AREA EQUAL TO
SIZE WELD TO
AREA OF BEAM FLANGE. GRADE OF DEVELOP FULL
1/4 2 SEE ARCH'L FOR PLATE TO MATCH GRADE OF BEAM. STRENGTH OF
DECK SCREW IPE DECK LENGTH OF PLATE TO BE AS REQUIRED BEAM FLANGE
T.O. BEAM EL. PATTERN EQ EQ SEE PLAN TO DEVELOP FILLET WELD.
IPE DECK
#3 REBAR (A706). SEE PLAN SEE PLAN www.datumengineers.com | Co. Reg. No. F-2819
EXTEND 8" MIN. INTO 1/4" JOINT WEB PLATE - SIZED Dallas Austin San Antonio
214-358-0174 512-469-9490 210-858-2880
CLAY TILE N.S. GROUT INTO BY FABRICATOR FOR
EXISTING CLAY T.O. DECK EL. Datum Project No. 19166
SEE PLAN T.O. DECK EL. ERECTION AND
TILE CELLS SEE PLAN BACKUP PLATE FOR DATE ISSUE TITLE
WELDING 04/03/2020 SCHEMATIC DESIGN PRESENTATION

ERECTION TC-U4a BEAM 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT
8" +/- 8" +/- FILL DEMO'D POCKET BOLTS TO BEAM WELD 08/31/2020 ISSUE FOR 100% DESIGN DEVELOPMENT
WITH N.S. GROUT AFTER 10/30/2020 ISSUE FOR PERMIT
AFTER TERRACE FLANGES, TYP. 12/18/2020 90% CONSTRUCTION DOCUMENTS
STEEL INSTALLATION T.O.S. EL. 01/25/2021 100% CONSTRUCTION DOCUMENTS
DEMO PORTION OF SEE PLAN
2" +/- 2" +/- T.O.S. EL.
PARAPET AS NEEDED
TO INSTALL NEW POST CONT. 2X NAILER WITH SEE PLAN TYP
3/8" DIA. BOLTS RESERVED FOR REVIEWERS NOTES
DOUBLE 2X10'S AT STAGGERED AT 24" O.C. 2X PURLINS

JOINT LOCATIONS COUNTERSINK IN NAILER SEE PLAN
WORKABLE GA. TOE-NAIL TO CONT. NAILER SHIM PLATES AS REQUIRED BY
BEAM SIZE WORKABLE 2X NAILER FABRICATOR FOR FIT-UP OR SMALL
GAGE DIFFERENCES IN BEAM DEPTH (NOMINALLY
SAME DEPTH). PLATE THICKNESS SHALL BE
W12X40 & 5 1/2" 2X10 SUFFICIENT TO TRANSFER REQUIRED
OVER CAPACITY OF CONNECTING WELDS. FILLET
W12X30 3 1/2" 2X8 BEAM .016 WELD ROOT OPENING SHALL NOT EXCEED
.016 SEE PLAN 3/16" OR REQUIREMENTS OF AWS D1.1.
W12X26 &
UNDER 2 1/4" 2X6 MOMENT CONNECTION SAME DEPTH BEAMS
1/2" = 1'-0" 11 1 1/2" = 1'-0" 12 1 1/2" = 1'-0" 13 TYPICAL DETAIL 15
FUTURE PLANTER, SEE
LANDSCAPE .016 05/03/2021 ADDENDUM 08
(335# PLF MAX.)
CL OF STEEL BEAM
BELOW AND BLOCKING EPA DECK SEE 4"
ARCH'L FOR EXTENTS
FUTURE EPA DECK

FUTURE 2X BLOCKING FUTURE 2X SEE PLAN
2X BLOCKING BLOCKING
2X BLOCKING
ALIGNED WITH FACE
2X8 NAILER FUTURE 2X PURLIN OF 2X8 NAILER
FUTURE 2X PURLIN
SEE PLAN FINISH
SEE ARCH'L
A
13/S623-OF SEE PLAN
ADDN'L 2X BLOCKING MAPLE TERRACE

BELOW PLANTER 3001 MAPLE AVENUE
2X PURLIN
SEE PLAN DALLAS, TEXAS, 75201
2X8 NAILER REQUIRED AT
PLAN
LOCATIONS WHERE 2X TERRACE SECTIONS AND
PURLIN IS DISCONTINUOUS
SECTION "A" .016 DETAILS
TEMPORARY DECK DETAIL AT FUTURE TENANT FINISH OUT 1" = 1'-0" 17 190013
PROJECT NUMBER
8 PL. TO 8 NOTE:
NOTE:
1/4 12" CHANNEL, TYP. S630-OF SEE 3/S630-OF FOR
S630-OF EXIST. 18"X18" SEE 3/S630-OF FOR
MIN. INFO. NOT SHOWN.
COLUMN INFO. NOT SHOWN.
2 5
EXIST. 18"X18" PL.1/2"
E-2.3 E2 14 13 E-1.8 S623-OF S623-OF E-1.7 10 E-1.6 COLUMN
DOUBLE BOLTS
8
SEE PLAN 6" +/- 1'-6" +/- PL.1/2 X AS SHOWN
4 SIDES S630-OF
1/4 4 6" +/- TYP. EACH SIDE
1'-0" +/-
8 EXIST. CONC.
5
S630-OF
1 1 SLAB & JOIST
S630-OF
SIM. 1 1 DEVELOPER
EXIST. ROOF 1/4 Hines
EXIST. 18"X18"
6" +/-
551'-2" EXIST. SLAB & COLUMN
HS JOIST 4/S630-OF Dallas, TX 75201
S4X EXIST. CONC. (972-716-2908 Corbin Eckel)
T=1 4X3/8
6" +/-
2k BEAM
/8
4X4X3 EXIST. T.O.S.C. EL. EXIST. T.O.S.C. EL. EXIST. T.O.S.C. EL. Houston, TX 77056
S (713-621-8000 Juan Delgado)
HS T=12k SEE PLAN SEE PLAN SEE PLAN
LEVEL 07
541'-2" EQUITY PARTNERS
HS McNair Interests
S6X
T=2 6X3/8
8" EMBED.
0k Houston, TX 77024
(Drew Steffen)
/8
6 X6X3
S
HS T=20k Mitsui Fudosan America
LEVEL 06 EXIST. CONC. 1251 Avenue of the Americas, Suite 800
531'-2" BASEMENT WALL New York, New York 10020
HS (David Leff)
S6X EXIST. SLAB
T=2 6X3/8 1
7k & JOIST 1 OFFICE/RETAIL ARCHITECT
/8 5G Studio Collaborative, LLC.
6X6X3 EXIST. CONC. 1217 Main St., Suite 500
S 3/4" DIA. HILTI HAS-E
HS T=27k BEAM Dallas, TX 75202
LEVEL 05 THREADED RODS (214-347-4982 Christine Robbins-Elrod)
6" +/- 6" +/- 1'-6" +/-
521'-2" WITH HIT/HY200
8
HS TYP. ADHESIVE
S6X S630-OF 4/S630-OF MASTER/MULTIFAMILY ARCHITECT
T=3 6X3/8 DOUBLE BOLTS GFF Architects
6
4k
X3/
8 TYP. 1" = 1'-0" 3 1" = 1'-0" 4 1" = 1'-0" 5 2808 Fairmount St., Suite 300
Dallas, TX 75201
S6 X (214-303-1500 Michael Reyes)
HS T=34k
LEVEL 04 NOTE:
511'-2" SCAN AND LOCATE EXIST PROVIDE OVERSIZED HOLES IN ZONING/ENTITLEMENT
HS REINF. SEE NOTE 7 AND 8 2" +/- NOTE:
S8X CHANNEL W/ PL.1/2X3X0'-3" Baldwin Associates
T=4 8X3/8 ON FIELD DRILLED ANCHOR WASHERS W/ STD. HOLE, TYP. SEE 10/S630-OF FOR WELDS. 3904 Elm Street, Suite B
3k NOTES: Dallas, TX 75226
NOTES ON S102-OF
/8 1. DESIGN WELDS TO CARRY MINIMUM BRACE FORCES SHOWN ON WB ELEVATIONS ON
8X3 EXIST. 18"X18" (214-824-7949 Robert Baldwin)
S8 X 1/S630-OF.
HS T=43k CONC. COLUMN
2. MINIMUM WELD LENGTHS TO BE 4" EA. SIDE. GEOTECH
1'-0"
LEVEL 03 3/4" DIA. F1554 GR55 THROUGH PL. 1/2" 3. USE FILLET WELDS FOR TUBES, WITH SPECIFIED LEG SIZE AND APPROPRIATE EFFECTIVE ECS Southwest, LLP
HS 501'-2" BOLTS IN 1" DIA. HOLES IN THROAT. 3033 Kellyway Drive, Suite 110
TYP., S8X CONCRETE @ 12" O.C.. 4. WELDS SHALL BE BALANCED ABOUT THE CENTROID OF THE BASE. Carrollton, TX 75006
4 U.N.O. T=4 8X3/8 STAGGERED AS SHOWN (8 (972-392-3222 Siddharth Neekhra)
S630-OF
9k 4 O.H., TYP.
6" +/-
TYP.
8 S630-OF BOLTS PER FLOOR). FILL HOLES
X8 X3/ PER NOTES ON S103-OF. CIVIL ENGINEER
S8
HS T=49k Kimley-Horn and Associates, Inc.
6" +/-
LEVEL 02 C12X20.7, TYP. 13455 Noel Road, Two Galleria Office Tower, Suite 700
491'-2" Dallas, TX 75240
HSS EXIST. T.O.S.C. EL.
8X (972-770-1300 Alex Rathbun)
SEE PLAN
T=5 8X3/8
3 7k TYP. 3 O.H., TYP. DETAIL "A" WELD TYPE: FILLET LANDSCAPE ARCHITECT
9
S630-OF /8 S630-OF
X8X3 S630-OF SWA Group
(F.V.)
8
1'-6"
HSS =57k SLOT TUBE TO FILLET WELD ALLOWABLE LOAD 2001 Irving Boulevard, Suite 157
T RECEIVE GUSSET NOMINAL SIZE (K/IN.) Dallas, TX 75207
LEVEL 01 GUSSET PLATE
EXIST. CONC. (214-954-0016 Chuck McDaniel)
481'-2" SEE ELEVATION 3/16" 10.8
SLAB & JOIST
AND DETAILS 1/4" 14.8 STRUCTURAL
4 SIDES
SIM. EXIST. CONC. BEAM H 5/16" 18.4
BUILT UP RAMP Datum Engineers
6" +/-
8 (MIN.)
C12X20.7 X CONT., TYP.
S630-OF
ELEVATION "A" Dallas, TX 75235
6" +/-
LEVEL B1 3/4" DIA. F1554 GR55
471'-0" MEP ENGINEER
THROUGH BOLTS IN 1" DIA. ME Engineers, Inc.
HOLES IN CONCRETE @ 18" 1825 Market Center Blvd., Suite 600
1'-0" +/-
O.C. (14 BOLTS). FILL HOLES Dallas, TX 75207
TYP.
PER NOTES ON S103-OF. (214-741-1589 Drew Shivley)
CONNECTION AT INTERSECTION OF X-BRACE TYPICAL DETAIL ELEVATOR CONSULTANT
WB-1 1 TYP.
1" = 1'-0" 8 TYPICAL DETAIL 9
NO SCALE
10 Persohn | Hahn Associates, Inc.
1/8"=1'-0" 3/16 NO SCALE McKinney, TX 75071
INTERIOR DESIGNER
Rottet Studio
Houston, TX 77002
(713-221-1830 x 6105 Anja Majkic)

214-358-0174 512-469-9490 210-858-2880

DATE ISSUE TITLE

MAPLE TERRACE
3001 MAPLE AVENUE
WIND BRACE ELEVATIONS AND
DETAILS
190013
PROJECT NUMBER
3 1/2" VERTICAL PLATE:
ROWS 3 SIDES 5/16" @ 3/4" DIA. BOLTS
1/4 3/8" @ 7/8" DIA. BOLTS 1/4
1/2" MAX. 3 SIDES THIS CONNECTION SHALL BE USED ONLY WHEN CONNECTING BEAMS TO 1/4
1/4 5/16 "A" BOLTS SIM.
1 1/2"
COLUMNS OR WHEN CONNECTING BEAMS TO GIRDERS WHERE GIRDER "A"
MIN
1 1/2"
1 1/2"
1 1/4" MIN.
MIN
MIN
GIRDER WEB, 4" HAS BEAM CONNECTION ON ONE SIDE ONLY. IF USED AT LOCATIONS "A"
COL. WEB
TYP.
SECT. "A"
1 1/2"
WHERE A BEAM CONNECTION IS OPPOSED BY A BEAM CONNECTION ON
MIN.
COL. WEB,
OR FLANGE THE OTHER SIDE OF THE SUPPORTING MEMBER, AN OSHA-APPROVED
BOLTS PLATE:
3"
METHOD MUST BE USED FOR TEMPORARY ERECTION SUPPORT OF BOTH
5/16" @ 3/4" DIA. BOLTS
BOLTS MEMBERS.
3/8" @ 7/8" DIA. BOLTS
MIN
3"
MIN
3"
3" TYP.
MIN
3" TYP.
MIN.
3"
DEVELOPER
3"
DOUBLE ANGLES STIFFENER TYP. Hines
L4x3 1/2x5/16 FOR 3/4" BOLTS COLUMN PL.3/8" 2200 Ross Avenue, Suite 4200W
L4x3 1/2x3/8 FOR 7/8" BOLTS PL. TO MATCH BEAM WEB SECT. "A" X=7" Dallas, TX 75201
SEE "ANGLES BOLTED COLUMN SECT. "A" X=7"
THICKNESS, 3/8" MINIMUM. 1 OR 2 VERT. ROWS MAX. (972-716-2908 Corbin Eckel)
TO BEAM" DETAIL X= 3" 1 1/4" @ 3/4" DIA. BOLTS MAX.
BELOW FOR MORE 1 1/4" @ 3/4" DIA. BOLTS MAX. 1 1/2" @ 7/8" DIA. BOLTS 2800 Post Oak Blvd., 49th Floor
NOTES X= 3" TYP. AT COLUMN Houston, TX 77056
MAX. 1 1/2" @ 7/8" DIA. BOLTS, AT GIRDER (713-621-8000 Juan Delgado)
SECT. "A" CONNECTION LOAD CAPACITY TYP.
ANGLES WELDED TO BEAM WELDED TO

BEAM
BOLTED TO
BEAM
CONNECTION LOAD CAPACITY (X = 7" MAX.) EQUITY PARTNERS
McNair Interests
# MINIMUM
WEB WEB CONNECTION LOAD CAPACITY 109 N. Post Oak Lane, Suite 600
3 1/2" WIDE BOLTS BEAM MIN. (X = 3" MAX.)
NOTE:
LARGER BM. REACTION MUST
# MINIMUM MAX REACTION (KIPS) Houston, TX 77024
MAX REACTION (KIPS) REDUCTION WIDE BOLTS BEAM (Drew Steffen)
ANGLE
FLANGE PER WEB CONNECTION LOAD CAPACITY (X = 3" MAX.)
1 1/2" MAX
BE LESS THAN 3 TIMES PER WEB

1 1/4" BEAM 3/4" DIA. 7/8" DIA. FOR COPED LENGTH FLANGE 3/4" DIA. BOLTS 7/8" DIA. BOLTS
COPE
VERT. THICKNESS 3/4" DIA. 7/8" DIA.

"A"
SIZE ROW (IN.) BOLTS BOLTS BOLTS BOLTS BOTTOM (IN.) MAX REACTION SMALLER BM. REACTION
BEAM VERT. THICKNESS
MINIMUM SIZE ROW (IN.) 1 ROW 2 ROWS 1 ROW 2 ROWS
OPTIONAL
COPED TOP W8 TO W12 2 .230 29 29 14 13 4 5 1/2 BEAM (KIPS) MAX REACTION (KIPS) BOLTS
(David Leff)
WIDE # BOLTS WEB W8x10 2 .170 4 2 5 3
W12 TO W18 3 .235 51 51 25 23 4 8 1/2
3 " 3"
FLANGE PER THICKNESS 3/4" DIA. 7/8" DIA. W10x12 2 .190 4 3 5 4 OFFICE/RETAIL ARCHITECT
W16 TO W24 4 .250 82 82 42 39 5 11 1/2 WIDE FLANGE # BOLTS PER
TYP
BEAM SIZE VERT. ROW (IN.) BOLTS BOLTS 3/4" DIA. BOLTS 7/8" DIA. BOLTS
GIRDER WEB, COL. W18 TO W30 5 .300 104 120 63 59 6 14 1/2 BEAM SIZE VERT. ROW W12x14 3 .200 8 10 11 11 5G Studio Collaborative, LLC.
W8x10 2 .170 14 14 W12x16 3 .220 8 13 11 15 1217 Main St., Suite 500
WEB, OR FLANGE W21 TO W40 6 .350 124 148 87 82 7 17 1/2 W8 TO W12 2 9 12 Dallas, TX 75202
W10x12 2 .190 14 20 W8 TO W12 2 .230 4 6 5 8 (214-347-4982 Christine Robbins-Elrod)
W24 TO W44 7 .395 145 172 115 108 8 20 1/2
W30 TO W44 8 .470 165 197 156 147 -- 23 1/2
W12x14
W12x16
3
3
.200
.220
26
26
29
32
TYP. SINGLE W12 TO W18
W16 TO W18
3
4
18
29
23
39
W12 TO W18 3 .235 8 16 11 18
W33 TO W44 9 .550 185 221 185 194 -- 26 1/2 W16 TO W24 4 .250 16 28 21 33
L4x4x3/8 ERECT. CLIP W36 TO W44 10 .600 205 245 205 235 -- 29 1/2
W8 TO W12 2 .230 14 20 PLATE BOLTED W18 5 41 56 SECT. "A"
W18 TO W30 5 .300 24 41 32 55
GFF Architects
1 1/2"
(NOT PERMITTED FOR BEAMS DEEPER THAN 18")

MIN
W12 TO W18 3 .235 26 34 W21 TO W44 6 .350 33 56 45 77 Dallas, TX 75201

WHERE BEAMS
FRAME TO BOTH STD. HOLES OR HORIZ.
SHORT SLOTS
W40 TO W44
W44
11
12
.630
.710
226
246
269
294
226
246
269
294
--
--
32 1/2
35 1/2
W16 TO W24 4 .250 37 51 CONNECTION W24 TO W44 7 .395 43 73 59 100 (214-303-1500 Michael Reyes)
SIDES OF COLUMN W18 TO W30 5 .300 48 65
WEB TYP. OPTIONAL COPED NOTE: VALUES IN THE COLUMNS LABELED "BOLTED TO BEAM WEB" MAY BE INCREASED BY THE W21 TO W44 6 .350 59 78 FOR BEAMS ON W30 TO W44 8 .470 54 92 74 126 ZONING/ENTITLEMENT
BOTTOM, REDUCE RATIO OF THE ACTUAL BEAM WEB THICKNESS TO THE MINIMUM BEAM WEB THICKNESS TABULATED. SHEAR TAB BOLTED W33 TO W44 9 .550 65 113 89 154 Baldwin Associates
CAPACITY AS FOR THIS CALCULATION THE BEAM WEB THICKNESS MAY NOT BE TAKEN MORE THAN 0.43" FOR 3/4"
W24 TO W44 7 .395 70 91
BOTH SIDES W36 TO W44 10 .600 77 134 105 183 3904 Elm Street, Suite B
Dallas, TX 75226
SHOWN IN TABLE DIA. BOLTS OR MORE THAN 0.62" FOR 7/8" DIA. BOLTS. W30 TO W44 8 .470 81 104
CONNECTION W40 TO W44 11 .630 88 155 120 212 (214-824-7949 Robert Baldwin)
W33 TO W44 9 .550 91 117 ONLY W44 12 .710 100 178 136 233
ANGLES BOLTED TO BEAM TYPICAL DOUBLE ANGLE CONNECTION

W36 TO W44 10 .600 102 130 FOR BEAMS ON ONE SIDE ONLY GEOTECH
A
W40 TO W44 11 .630 112 143
B SINGLE PLATE BOLTED CONNECTION ECS Southwest, LLP
NO SCALE TYP. W44 12 .710 123 156 C D
CIVIL ENGINEER
RETURN C.L. SUPPORT Kimley-Horn and Associates, Inc.
90
W 2W USE THIS DETAIL FOR CONNECTING STEEL BEAMS TO EMBED PLATES ONLY .
LENGTH OF WELD RETURN AT 13455 Noel Road, Two Galleria Office Tower, Suite 700
°
TOP IS EQUAL TO 2 TIMES
CONNECTION LOAD CAPACITY Dallas, TX 75240
BEYOND STUDS
THE WELD SIZE. (972-770-1300 Alex Rathbun)
4"
1'-9" MIN.
1 1/4" 3" #
"A" WIDE WELDED TO GIRDER BOLTED TO GIRDER MIN. 2" CLR. HOOK #4 HORIZ. BARS 3" FROM LANDSCAPE ARCHITECT
BOLTS
1 1/2"
FLANGE ANGLE EDGE OF CONCRETE WHERE

MIN.
SWA Group
PER STRAIGHT BARS WILL NOT FIT AS
BEAM MAX REACTION (KIPS) LENGTH 1 1/4" 1" NOMINAL 2001 Irving Boulevard, Suite 157
VERT. SHOWN Dallas, TX 75207
SIZE (IN.) SEE ELEV. "A" CLR. 2" MAX.
ROW 3/4" DIA. 7/8" DIA. 3/4" DIA. 7/8" DIA. PL. 3/4 x 12 (214-954-0016 Chuck McDaniel)
SINGLE ANGLE: BOLTS BOLTS BOLTS BOLTS ADDITIONAL #4
1'-9"
L4X3X3/8 UP TO 1 STRUCTURAL
W8 TO W12 2 21 22 10 14 5 1/2 HORIZ. x 4'-0" @
TYP.
SEE TABLE FOR

3"
W12 TO W18 3 31 35 21 28 8 1/2 6" VERT. 1/4 SIZE Datum Engineers

12 C.L. SKEWED BEAM BEHIND PLATE 4 #4 HAIRPINS (2 AROUND EACH VERT. ROW OF 6516 Forest Park Road
W16 TO W24 4 42 48 32 44 11 1/2 HEADED STUDS) W/ STD. HOOK AT TOP OF EACH Dallas, TX 75235
W18 TO W30 5 53 61 43 59 14 1/2 3 SIDES LEG - TIE TO HEADED STUDS (2 #4 VERT. BARS (214-358-0174 Rodolfo D'Arlach)
4"
3/16
TWO ANGLES TWO BENT ANGLES
1 1/4"
W21 TO W40 6 63 74 55 75 17 1/2 MAY BE SUBSTITUTED FOR EACH HAIRPIN

TYP.
ELEV. "A"
WHERE THEY CAN BE EXTENDED AT LEAST 21" MEP ENGINEER
W24 TO W44 7 74 86 66 90 20 1/2
6"
BEYOND LAST ROW OF STUDS) ME Engineers, Inc.
CONNECTIONS ARE USED
1'-1 7/8"
W
INSTALLATION OF BOLTS
W30 TO W44 8 84 98 77 105 23 1/2 1825 Market Center Blvd., Suite 600
CONTRACTOR TO SET
W33 TO W44 9 95 110 88 120 26 1/2 Dallas, TX 75207
SECT. "A"
6"
THIS DIMENSION TO
W36 TO W44 10 106 123 99 134 29 1/2 HAIRPINS AROUND HEADED
WHERE BOLTED
ALLOW PROPER
WELD SIZE "W" IS 1/4" W40 TO W44 11 117 135 110 149 32 1/2 STUDS - SEE ELEV. "A" 2-L4x4 MIN. LEG THICKNESS
EQUAL TO WELD SIZE + 1/16" ELEVATOR CONSULTANT
FOR 3/4" DIA. BOLTS
4"
W44 12 127 147 120 164 35 1/2
WELDED TO GIRDER AND 5/16" FOR 7/8"
DIA. BOLTS OPTIONAL ELEV. "A"
McKinney, TX 75071
4" ERECTION SEAT (972-832-4232 Tom Williams)
1 1/2"
MIN.
C.L. SUPPORT
1 1/4" 4" CONNECTION LOAD CAPACITY
.
"B" INTERIOR DESIGNER
1 1/2"
FACE OF CONCRETE OR
MIN.
7" LONG HEADED STUDS EXISTING STRUCT. STEEL WIDE 1/4" 5/16" Rottet Studio
PURLIN
BOLTS @ 8" O.C. HORIZONTAL FLANGE ANGLE WELD & WELD & Houston, TX 77002
2 1/2"
GIRDER .CONTRACTOR TO SET (SEE TABLE FOR QUANTITY) STUDS (713-221-1830 x 6105 Anja Majkic)
SINGLE OVER 4 THIS DIMENSION TO

BEAM LENGTH 3 KSI 4 KSI
TYP.
C.L. OF BOLT
SIZE CONC. CONC.
3"
ANGLE: 12 ALLOW PROPER

L4x4x3/8 INSTALLATION OF BOLTS
OVER 1 TO 8 NOTES: W8 TO W12 5.5 16 20 4-7/8" DIA.
WHERE BOLTED
C.L. SKEWED BEAM 1. STUDS TO BE LOCATED A MIN. OF 4" FROM
CONNECTIONS ARE W12 TO W18 8.5 35 41 8-7/8" DIA. www.datumengineers.com | Co. Reg. No. F-2819
ANY EDGE OF CONCRETE SUPPORT.
1 1/4"
USED Dallas Austin San Antonio

TYP.
12 W16 TO W24 11.5 49 57 12-7/8" DIA. 214-358-0174 512-469-9490 210-858-2880

SINGLE ANGLES MUST STAGGER AS 12 C.L. OF BOLT 2. EMBED PLATES MAY BE INCREASED IN SIZE
SHOWN WHEN CONNECTION TO LIMIT THE NUMBER OF DIFFERENT SIZE Datum Project No. 19166
W18 TO W30 14.5 63 72 16-7/8" DIA.
2 1/2" TO TO GIRDER IS A FIELD CONNECTION C.L. SKEWED BEAM PLATES. DATE ISSUE TITLE
TO BEAM C.L. OVER 8 W21 TO W36 14.5 70 80 18-7/8" DIA.
3. CONCRETE REINFORCING IS CRITICAL TO 04/03/2020 SCHEMATIC DESIGN PRESENTATION
TWO BENT PLATES ACHIEVE THE TABULATED CAPACITIES. 05/06/2020 ISSUE FOR SCHEMATIC DESIGN
PLAN VIEW SINGLE BENT PLATE W24 TO W36 14.5 76 88 20-7/8" DIA.
ENGINEER SHALL BE NOTIFIED WHEN
BOLTED TO GIRDER SECT. "B"
NOTE:
REINFORCING CANNOT BE PLACED AS
INDICATED.
07/22/2020
08/31/2020
DESIGN SINGLE BENT PLATE
CONNECTION FOR SINGLE SHEAR AND SKEWED SIMPLE FRAMING CONNECTIONS - BEAM TO BEAM 12/18/2020 90% CONSTRUCTION DOCUMENTS
ECCENTRICITY REFER TO CONNECTION
TYPICAL SINGLE ANGLE CONNECTION "E" TYPICAL DETAIL DOUBLE ANGLE CONNECTION WELDED TO EMBED PLATES
E F G RESERVED FOR REVIEWERS NOTES
X = 5"
REACTION IS CALCULATED FROM THE DROP-IN SPAN. WIDE FLANGE 3" PLATE:
MAX.
"A"
SIZE IS THE SMALLER OF THE DROP-IN BEAM OR THE SUPPORTING
BEAM.
CENTER LINE OF
COLUMN AND BEAM
MAX 1/4" @ 3/4" DIA. BOLTS (3/16" TUBE WALL THICK. MIN.)
5/16" @ 3/4" DIA. BOLTS (1/4" TUBE WALL THICK. MIN.) 3" MAX CONNECTION NOTES
X=3 1/4" 3/8" @ 7/8" DIA. BOLTS (5/16" TUBE WALL THICK. MIN.)
NOTE: PRE-ENGINEERED CONNECTION DETAILS ARE PROVIDED TO ASSIST THE DETAILER AND FABRICATOR.
MAX. PLATE:
MIN.
A/2
WHERE THESE PRE-ENGINEERED DETAILS ARE USED THEN NO DESIGN WORK IS REQUIRED BY THE
MIN
MIN
Lev
Lev
SLOTS NOT ALLOWED 5/16" @ 3/4" DIA. BOLTS SLOT COLUMN
1 1/2"
MIN.
WHERE H=_ IS USED FABRICATOR AND NO CALCULATIONS ARE REQUIRED TO BE SUBMITTED. WHERE THESE PRE-
3/8" @ 7/8" DIA. BOLTS FOR PLATES AS ENGINEERED DETAILS ARE USED, ALL ASPECTS OF THE CONNECTIONS MUST CONFORM TO THE PRE-
SHOWN Leh = 1 1/2" FOR 3/4" DIA. Leh Leh ENGINEERED DETAILS.
Leh Leh 1 3/4" FOR 7/8" DIA MIN MIN
"A"
3/8" THICK SHEAR
TYP
MIN
SEE PLAN FOR MIN MIN
3"
3"
PLATES BOTH THE FABRICATOR MAY, AT HIS OPTION, SUBMIT ALTERNATE CONNECTION DETAILS FOR USE ON THE
BEAM Lev = 1 1/4" FOR 3/4" DIA.
PROJECT. ALTERNATE CONNECTION DETAILS MUST CONFORM TO THE CONCEPTS SHOWN IN THE PRE-
MIN.
SIDES
A
1 1/2" FOR 7/8" DIA.

3"
ENGINEERED CONNECTION DETAILS. SUBMITTALS CONTAINING ALTERNATE CONNECTION DETAILS MUST
MIN
Lev
MIN
Lev
1 1/4" @ 3/4" DIA. BOLTS BOLTS TYP INCLUDE DESIGN CALCULATIONS SEALED BY A REGISTERED ENGINEER PER THE SPECIFICATIONS. REV. DATE ISSUE TITLE
1 1/2" @ 7/8" DIA. BOLTS, 3/16
TYP .05 12/18/2020 Permit Set Update
TYP.. DETAIL K BEAMS OF VARIOUS WEB THICKNESSES ARE GROUPED BASED ON THEIR DEPTH. NUMBER OF BOLTS
PROVIDE SHORT-SLOTTED HOLES TYP
1 1/4" 3/16 @3/4" DIA. BOLTS w/ 3/16" TUBE WALL SHOWN ARE THEREFORE BASED ON THE THINEST WEB IN EACH GROUP.
MIN.
IN PLATE AT DROP-IN SIDE FOR 1/4 @ 3/4" DIA.

A/2
TYP. 1/4 @3/4" DIA. BOLTS w/ 1/4" TUBE WALL 1/4@3/4" DIA. BOLTS
ADJUSTMENT BOLTS
2" 5/16 @7/8" DIA. 5/16 @7/8" DIA. BOLTS w/ 5/16" TUBE WALL 5/16@7/8" DIA. BOLTS CONNECTIONS SHOWN IN THE DRAWINGS WHICH ARE NOT COVERED BY THE PRE-ENGINEERED DETAILS
MAX. BOLTS SUCH AS TRUSS CONNECTIONS, WIND BRACE CONNECTIONS OR OTHER NON TYPICAL CONNECTIONS
DROP-IN SIDE OPTIONAL COPED BOTTOM SECT. "A" SECTION "A" MUST BE DESIGNED BY THE FABRICATOR AND SUBMITTED WITH DESIGN CALCULATIONS SEALED BY A
ON DROP-IN SIDE ONLY TUBE COL.-WALL THICKNESS MIN. REGISTERED ENGINEER PER THE SPECIFICATIONS. NUMBER OF ROWS OF BOLTS IN SIMPLE BEAM
INTERSECTING BEAMS AT PIPE COLUMN 3/16" @ 3/4" DIA. BOLTS (REDUCED CAPACITIES) CONNECTIONS SHALL NOT BE LESS THAN THE NUMBER FOUND BY DIVIDING THE SMALLER BEAM DEPTH
ELEVATION 1/4" @ 3/4" DIA. BOLTS (IN INCHES) BY SIX, AND ROUNDING UP ANY FRACTION TO THE NEXT HIGHER NUMBER.
5/16" @ 7/8" DIA. BOLTS
CONNECTION LOAD CAPACITY
CONNECTION LOAD CAPACITY SEE TABLE IN DETAIL "D" IF NOTES:
MAX REACTION COLUMN SIZE FORCES "X" DIM TO CONNECTION LOAD CAPACITY 1. FABRICATOR SHALL SELECT TYPICAL BEAM CONNECTIONS FROM THESE DETAILS USING LOAD
# MINIMUM (KIPS) # MINIMUM
MAX REACTION (KIPS) BE LARGER THAN 5", BUT NOT REACTIONS GIVEN ON THE PLAN (AS _K) OR SCHEDULE. WHERE REACTIONS ARE NOT PROVIDED FOR
MORE THAN 7". # MINIMUM COMPOSITE BEAMS, DESIGN CONNECTIONS TO DEVELOP THE FULL CAPACITY OF THE BEAM WEB IN
WIDE BOLTS BEAM WIDE BOLTS BEAM
3/4" DIA. BOLTS 7/8" DIA. BOLTS
WIDE
BOLTS BEAM
MAX REACTION (KIPS) SHEAR. WHERE REACTIONS ARE NOT PROVIDED FOR NON-COMPOSITE BEAMS, DESIGN
FLANGE PER WEB 3/4" DIA. BOLTS 7/8" DIA. BOLTS FLANGE PER WEB FLANGE CONNECTIONS FOR 60 PERCENT OF THE MAXIMUM TOTAL ALLOWABLE (ASD) UNIFORM LOAD FOR THE
PER WEB
BEAM VERT. THICKNESS X = 3 1/4" X = 3 3/4" BEAM VERT. THICKNESS BEAM
VERT. THICKNESS 3/4" DIA. BOLTS 3/4" DIA. BOLTS 7/8" DIA. BOLTS BEAM SIZE AND SPAN GIVEN IN THE 50 KSI TABLES IN PART 3 OF THE AISC STEEL CONSTRUCTION
SIZE ROW (IN.) BOLTS BOLTS SIZE ROW (IN.) 1 ROW 2 ROWS 1 ROW 2 ROWS SIZE (3/16" WALL THK) (1/4" WALL THK) (5/16" WALL THK) MANUAL.
ROW (IN.)
W8x10 2 .170 15 14 W8x10 2 .170 19 19 19 19
W8x10 2 .170 16 19 19 2. ALL BEAM REACTIONS ARE IN KIPS, AT SERVICE LOADS (UNFACTORED).
W10x12 2 .190 18 24 W10x12 2 .190 20 22 25 25
W10x12 2 .190 16 20 25
W12x14 3 .200 30 29 W12x14 3 .200 31 34 35 35 3. TABULATED CONNECTION CAPACITIES ARE UNFACTORED AND ARE BASED ON GRADE 50 BEAMS,
W12x14 3 .200 25 31 35
W12x16 3 .220 33 32 W12x16 3 .220 31 34 38 38 A36 PLATES AND ANGLES, A325N BOLTS (BEARING TYPE) AND E70XX ELECTRODES.
W12x16 3 .220 25 31 38
W8 TO W12 2 .230 18 20 W8 TO W12 2 .230 20 23 26 26
W12 TO W18 3 .235 36 34 W12 TO W18 3 .235 31 34 39 39 THROUGH W8 TO W12
W12 TO W18
2
3
.230
.235
16
25
20
31
26
39
SINGLE 4. SLOTTED HOLES ARE NOT PERMISSIBLE EXCEPT WHERE SHOWN.
W16 TO W24
W18 TO W30
4
5
.250
.300
53
70
51
67
W16 TO W24
W18 TO W30
4
5
.250
.300
41
52
46
57
52
65
52
65 PLATE W16 TO W24 4 .250 34 42 52 PLATE 5. WHERE HORIZONTAL FORCES ARE SHOWN ON THE PLAN (AS H=_K), THE FABRICATOR SHALL
SIZE THE CONNECTION TO TRANSFER THE HORIZONTAL FORCE IN ADDITION TO THE REQUIRED MAPLE TERRACE
W18 TO W30 5 .300 43 53 65 VERTICAL REACTION (CONNECTION CAPACITY=V+H). SLOTTED HOLES ARE NOT PERMITTED.
W21 TO W44
W24 TO W44
6
7
.350
.395
97
126
92
119 TYPICAL SHEAR
W21 TO W44
W24 TO W44
6
7
.350
.395
62
72
69
80
78
91
78
91
CONNECTION W21 TO W44 6 .350 51 63 78 CONNECTION 3001 MAPLE AVENUE
W24 TO W44 7 .395 59 74 91 6. COMPLY WITH AISC MIN. EDGE DISTANCES.
W30 TO W44 8 .470 150 187 W30 TO W44 8 .470 83 92 104 104
AT TUBE AT COLUMN SIMPLE BEAM CONNECTION
W33 TO W44 9 .550 173 234 SPLICE CONNECTION W33 TO W44 9 .550 93 103 117 117
W30 TO W44
W33 TO W44
8
9
.470
.550
67
75
84
94
104
117 DETAILS
W36 TO W44 10 .600 195 261 W36 TO W44 10 .600 104 115 130 130 COLUMN W36 TO W44 10 .600 83 103 129
W40 TO W44
W44
11
12
.630
.710
217
238
287
313
W40 TO W44
W44
11
12
.630
.710
114
124
127
138
143
156
143
156 J W40 TO W44 11 .630 91 111 141 K L S640-OF
H W44 12 .710 100 118 153
190013

MT - Office Structural CA Set

Uploaded by

Copyright:

Available Formats

MT - Office Structural CA Set

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MT - Office Structural CA Set

Uploaded by

Copyright:

Available Formats

What are some common structural abbreviations mentioned in the document?

What are some common structural abbreviations mentioned in the document?

What project details are provided on page 55?

What project details are provided on page 55?

TYPICAL STRUCTURAL ABBREVIATIONS ALL ABBREVIATIONS SHOWN

FIELD VERIFY (F.V.) 7. SEISMIC DESIGN DATA (IBC):

40 BAR DIAMETERS FOR #5 BARS AND SMALLER

56 BAR DIAMETERS FOR #6 AND #7 BARS

60 BAR DIAMETERS FOR #8 AND #9 BARS

13. HORIZONTAL WALL JOINT REINFORCING SHALL BE STANDARD TRUSS TYPE AS

18. PROVIDE 3/8" THROUGH-WALL CONTROL JOINTS AT 40'-0" MAXIMUM SPACING OR AT

2800 Post Oak Blvd., 49th Floor

Mitsui Fudosan America

S305-OF E/S302-OF OUTLINE OF ELEVATOR CONSULTANT

3'-9 1/2" F DATE ISSUE TITLE

3. SEE SHEET S101-OF, S102-OF AND S103-OF FOR GENERAL NOTES

2800 Post Oak Blvd., 49th Floor

Mitsui Fudosan America

E-C LANDSCAPE ARCHITECT

STAIR 1 S222-OF S222-OF S305-OF OUTLINE OF Dallas, TX 75235

(713-221-1830 x 6105 Anja Majkic)

11 Datum Project No. 19166

SEE GARAGE DRAWINGS FOR 1 04/03/2020 SCHEMATIC DESIGN PRESENTATION

30'-0" 30'-0" 30'-0" 30'-0" 30'-0" 2'-4"

1 LEVEL B2 REV. DATE ISSUE TITLE

3. SEE SHEET S101-OF, S102-OF AND S103-OF FOR GENERAL NOTES

1/8" = 1'-0" MASTER/MULTIFAMILY ARCHITECT

E-B STYROFOAM SEE

S306-OF S306-OF 12 S306-OF 12 (4 LOCATIONS) E-B.5 (214-954-0016 Chuck McDaniel)

P=275k FOR OFFICE P=275k 9" Datum Engineers

20/S610A-OF 1" E.J. SIM.

NEW DOOR IN EXISING P1, CC/S302-OF

BASEMENT 1825 Market Center Blvd., Suite 600

S304-OF 8612 Broad Meadow Lane

8 SHEARWALLS SEE 3/S613-OF

ELEV. E/S302-OF (972-832-4232 Tom Williams)

17 16 (713-221-1830 x 6105 Anja Majkic)

S221-OF S306-OF S502-OF S502-OF

2'-4" UNDERPINNING S306-OF 7'-8" 19

FOR OFFICE BUILDING SEE S303-OF

PIER DRILLING OPERATIONS.

DATE ISSUE TITLE

P=275k 04/03/2020 SCHEMATIC DESIGN PRESENTATION

20/S610A-OF P3,20CC/S302-OF 07/22/2020 ISSUE FOR 50% DESIGN DEVELOPMENT

10/30/2020 ISSUE FOR PERMIT

VERIFY SIZE, DEPTH, 9" 01/25/2021 100% CONSTRUCTION DOCUMENTS

REV. DATE ISSUE TITLE

3. SEE SHEET S101-OF, S102-OF AND S103-OF FOR GENERAL NOTES

2800 Post Oak Blvd., 49th Floor

Mitsui Fudosan America

5'-6 1/4" (F.V.)

BE REQUIRED IN THESE LOCATIONS.

16/S610-OF 10 16/S610-OF 1/S630-OF BASEMENT WALL

TO BE DEMO'D S305-OF SEE 3/S613-OF, TYP. BELOW Dallas, TX 75207

STAIR 1 S222-OF S222-OF ME Engineers, Inc.

ADDN'L 3#7X12'-0" 5 S305-OF AHU

B105 B107 8612 Broad Meadow Lane

S305-OF EITHER SIDE OF BRIDGE.

B103 S305-OF P DL = 6k, P LL = 6k RETENTION SYSTEM Houston, TX 77002