Cream Concentrated Latex For Foam Rubber Products
Cream Concentrated Latex For Foam Rubber Products
Cream Concentrated Latex For Foam Rubber Products
Abstract. Fresh natural latex (around 40% rubber and 60% water) can be transformed to
concentrated natural latex (around 60% rubber and 40% water) in order to realise economical
transportation and easier latex product’s preparation. The concentrated natural latex is an
extremely valuable material. It can be applied for many types of products, for example, foam
rubber as pillow and mattress, elastic band, etc. Industrially, the concentrated natural latex can
be prepared by centrifugation which requires an enormous expensive machine. From the eco-
friendly products point of view, most of rubber entrepreneurs in the world try to develop a
green rubber product. So, the main objective of this study is to prepare the cream concentrated
latex without any sophisticated machine. Thus, we work on a simple, cheap and green method
that does not use any expensive machine but uses water-based chemical as sodium alginate to
prepare the cream concentrated latex. The optimal amount of sodium alginate in the latex was
studied. The main characteristics of the cream concentrated latex were tested by various
technics, such as alkalinity, total solid content (TSC), dry rubber content (DRC), etc. We found
that there are no significant differences of results between fresh natural latex and cream
concentrated latex, except for the TSC and DRC. The TSC and DRC of cream latex are higher
than those of fresh natural latex. Finally, we propose a model of natural rubber particle and
sodium alginate to form the cream concentrated latex.
1. Introduction
Natural rubber is made from runny milky white liquid called latex. Although there are something like
200 plants in the world that produce latex, however, the world's natural rubber is industrially made
from the latex that comes from a specific tree species called Hevea brasiliensis. Fresh natural latex can
be collected from a tapped rubber tree. Fresh natural latex is a colloidal system of natural rubber
particle in micron size dispersed in an aqueous medium and contain 30-40% of dry rubber content
(Table 1) [1-2].
Composition of fresh natural latex depends on factors such as soil condition, fertilizer quality, tapping
system, season, etc. Fresh natural rubber latex can be contaminated by micro-organism because natural
latex contains various nutritious substances, otherwise known as non-rubber components [3-4]. The
micro-organism consumes these non-rubber constituents and then generates the volatile fatty acid
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution
of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
Published under licence by IOP Publishing Ltd 1
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
(VFA) which enables the destabilisation of latex particles. Normally, we use ammonia solution to
neutralise the VFA in the latex that keep the stabilization of latex. So, ammonia solution is used to
preserve the natural latex. Fresh natural latex can be transformed to concentrated natural latex in order
to maintain the constant quality of concentrated natural latex and to generate the economic value for
latex’s transportation.
Concentrated natural latex contains 60% rubber, which is essential in making products such as foam
rubber as pillow and mattress, elastic band, etc [5]. The concentrated natural latex can be produced by
various processes including evaporation, electrocantation, centrifuging and creaming. Evaporation
refers to the removal of water by floating a double-walled cylindrical vessel and a hollow iron roller in
the latex and spray hot latex into partially evacuated chamber. Electrocantation immerses positive
electrode into latex. As a result, the positive was combined and would float up on the surface of latex.
Centrifuging, in which the latex is placed into a centrifuge and later it is centrifuged to remove some
of the water in order to increase the rubber content of latex.
The centrifugation process for concentrated natural latex is very well known and is used widely for
commercial purpose, but it uses a big, expensive machine and adding chemical agent (TMTD) to
preserve the natural latex that cause the cancer from nitrosamine. One of the methods for preparing
concentrated natural latex is creaming, the creaming method is a chemical process that mixes
creaming agent and fresh natural latex and facilitates phase separation (rubber fraction and serum).
Creaming agent helps in increasing the creaming efficiency. Cream concentrated latex was
successfully prepared using a creaming agent include sodium carboxymethyl cellulose, poly(vinyl
alcohol), methyl cellulose, carboxymethyl cellulose, locust bean gum, tamarind seed powder, casein
and sodium alginate [6-7]. This method is environmentally friendly for it requires simple equipment
and incurs lower power consumption. The main objective of this paper is to prepare the cream
concentrated latex using sodium alginate as a creaming agent. Various properties of the cream
concentrated latex were characterized and compared with the fresh natural latex. This aspect has not
been reported in the previous literature reviewed.
2. Experimental
2.1. Materials
Fresh natural latex was kindly collected from plantation in the southern of Thailand (Tha chang
industries group, Suratthani). The characteristics of latex are in the table 2. Sodium alginate was
supplied from Thanodom trading, Thailand. Ammonia solution was supplied from RCL Labscan, it
was used as a latex preservative against bacteria attack and yo provide long-term stability..
2
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
DRC 27.28%
DRC 60.13%
2.3. Characterizations of the fresh natural latex and cream concentrated latex
Analysis and testing of latex properties include total solid content (TSC), dry rubber content (DRC),
Alkalinity (%), Volatile fatty acid (VFA) and Mechanical stability (MST) as shown below.
2.3.1. Total solid content (TSC) (ISO, 124). Pour 2 g of latex into the dish and determine the exact
mass by weighing, approximate to the nearest 0.1 mg, then place the dish in the oven at 105 ± 5oC for
2 h, or until the test portion has lost its whiteness. Remove the dish from the oven and allow it to cool
to ambient temperature.
2.3.2. Dry rubber content (DRC) (ISO 126). 10 ± 1 g of latex concentrate into dish. Add of 20 g/dm3
acetic acid solution, pouring it down along the inner edge of dish and slowly rotating the dish while
the acid is being added. When the serum is clear, collect any small particles of coagulated rubber by
rubbing with the main bulk. Soak the coagulated rubber in several change of water until the water is
no longer acidic to litmus, after that running of water for at least 5 min. Dry the sheet at 70 ±5°C until
it has no white patches.
2.3.3. Alkalinity (%) (ISO, 125). A test portion of latex is titrated with acid to pH 6 in the presence of a
stabilizer to prevent coagulation, either electrometrically or with methyl red as a visual indicator. The
alkalinity is calculated from the quantity of acid required.
2.3.4. Volatile fatty acid or VFA (ISO, 506). A test portion is coagulated with ammonium sulphate and
a portion of the resultant serum is separated and acidified with sulphuric acid. The acidified serum is
steam-distilled and the volatile acids present in the test portion are determined by titration of the
distillate with a standard volumetric barium hydroxide solution
2.3.5. Mechanical stability (MST) (ISO, 35). A test portion of latex is diluted to 55% by mass total
solids content and stirred at high speed. The time required to initiate visible flocculation is recorded,
this regarded as a measure of the mechanical stability.
3
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
When fresh natural latex was added the creaming agent, two layers of latex appeared or we can call it
“the creaming phenomenon”. The upper layer is cream concentrated latex, it was then added ammonia
solution with a concentration of 0.6% for its preservation. On the other hand, the lower fraction is
serum that is separated from the cream latex by gravity with the activity of the added creaming agent.
Figure 1 presents the quantity creaming agent at 1, 2, 3, 4, and 5 ml in the fresh natural latex at 25 ml.
The creaming phenomenon was observed at different incubation times. This figure shows the
relationship between incubation time and quantity of creaming agent. We found that incubation time is
decreased with increasing of creaming agent then reached at a constant value of incubation time for 4
ml of creaming agent. So, the optimal quantity of creaming agent is 4 ml in fresh natural latex 25 ml,
this optimal ratio will be applied for the other sections.
50
Incubation time for separation (h)
40
30
20
10
0 1 2 3 4 5 6
Creaming agent (ml)
Characterizations of fresh natural latex and cream concentrated latex were compared in table 3. When
fresh natural latex is transformed to concentrated natural latex by creaming process using sodium
alginate as a creaming agent, we found that TSC and DRC values of the cream concentrated latex are
clearly higher than those of fresh natural latex. This proves that the sodium alginate provides
efficiency to separate rubber particles from the serum solution. However, there are no significant
differences of alkalinity and VFA between fresh natural latex and cream concentrated latex. The cream
concentrated latex was still incubated just 3 days with 4 ml of creaming agent. The alkalinity indicates
to the ammonia level in latex and the VFA indicates to the degradation of latex by micro-organism.
The results from table 3 mean that both types of latex are in good condition and are not yet degraded.
4
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
Figure 2 shows TSC and DRC values of cream concentrated latex with incubation time. The TSC and
DRC values of cream concentrated latex increased in the first month and then reached the plateau
constant value with longer period of incubation time. The TSC value is always higher than DRC value
because TSC includes rubber and non-rubber components, while the DRC presents only rubber
component.
60
50
TSC and DRC (%)
40
30
TSC
20 DRC
10
0
0 1 2 3 4
Incubation time (Month)
Mechanical stability or MST level relates to incubation time as in the figure 3, indicates that cream
concentrated latex has higher MST with increasing incubation time or storage time. This is attributed
to the increase fatty acid soap from hydrolysis of the phospholipid and ammonia solution [6]. It has
been known that the fatty acid soap is adsorbed at the surface of rubber particle to form hydration
layer to cover rubber particle [8]. This affects the enhancement of the colloid stability of the latex and
thus increasing MST.
5
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
180
160
Mechanical stability time (s)
140
120
100
80
60
40
20
0
0 1 2 3 4
Incubation time (Month)
Sodium alginate is used as a creaming agent with high degree of polarity (hydroxyl group, -OH) and
sequences of the mannuronate and glucuronate residues (figure 4). The sodium alginate can become
hydrophilic colloids dispersed in the latex and interacts with the rubber particles through the negative
charges at the surface of particles (figure 5).
6
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
Sodium alginate
Natural rubber
The sodium alginate molecules cover the surface of rubber particles (figure 5), more adsorption of
sodium alginate molecules at the surface of rubber particles with longer incubation time. The branched
segments of the sodium alginate molecule could be entangled with the sodium alginate in
neighbouring rubber particles, this causes larger size of rubber particle. High molecular weight sodium
alginate with a number of hydroxyl groups (OH) led to higher viscosity of the latex and cause to
slowly movement of rubber particles [6].
4. Conclusions
We have succeeded in preparing the concentrated natural latex using creaming technic with the
optimal amount of creaming agent. Cream concentrated natural latex using sodium alginate as a
creaming agent represented higher TSC and DRC compared to the fresh natural latex. The other
properties of both types of latex show no significant differences, except for the MST of cream
concentrated latex increasing with the increase of incubation time. We also propose a model to explain
the cream concentrated latex between sodium alginate and rubber particles. This type of concentrated
latex could be applied for the foam rubber products, especially green rubber products.
5. Acknowledgments
The authors gratefully acknowledge the financial support of the Graduate School Kasetsart University,
Bangkok, Thailand, and National Science and Technology Development Agency (NSTDA) from the
STEM Workforce, Thailand.
6. References
[1] Smitthipong W, Nardin M, Schultz J, Nipithakul T and Suchiva K 2004 J. Adhesion Sci.
Technol. 18 1449.
[2] Smitthipong W, Nardin M and Schultz J 2008 Kasetsart J. (Nat. Sci.) 42 318.
[3] Vallat M-F, Radabutra S, Thanawat S, Bresson B, Chollakup R, Rungsanthien K, Suwanruji P,
Sriroth K, Smitthipong W and Mougin K 2014 Adv. Mat. Res. 844 369.
[4] Smitthipong W, Tantatherdtam R, Rungsanthien K, Suwanruji P, Sriroth K, Radabutra S,
Thanawat S, Vallat M-F, Nardin M, Mougin K and Chollakup R 2014 Adv. Mat. Res. 844
345.
[5] Smitthipong W, Suethao S, Shah D and Vollrath F 2016 Polym. Testing 55 17.
7
ICMMM 2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 272 (2017) 012025 doi:10.1088/1757-899X/272/1/012025
1234567890
[6] Yimae N, Kaesaman A, Rungvichaniwat A, Thepchalerm C and Nakason C 2010 J. Elast. Plast.
42 453.
[7] Ochigbo S S, Lafia-Araga R A and Suleiman M A T 2011 African J. Agricul. Res. 6 2916.
[8] Blackly D C 1997 Polymer Lattices, London, Chapman & Hall 2 106.