SAUDIARAMCO.

NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS
OTHERWISE NOTED.

2. ALL STRUCTURAL STEEL MATERIAL SHALL BE

ASTM-A36/A36M AS PER 12-SAMSS-007.

LENGTH ( L )
3. ALL STRUCTURAL STEEL FABRICATIONS AND
INSTALLATION SHALL BE IN ACCORDANCE WITH

OF
L/2 L/2 SAES-M-001 & 12-SAMSS-007/008.

CONSENT
4. ALL WELDING SHALL BE IN ACCORDANCE WITH
| CARRIER PIPE
PLATE INSIDE DIAMETER (ID) AWS-D1.1.

5. ALL STRUCTURAL STEEL OF PIPE ANCHOR SHALL

2NOS-6mm NPT VENT HOLE BE COATED AS PER APCS-104 0F SAES-H-001.

TTEN
| (SEE NOTE -10)
6. PIPE SLEEVE SHALL BE FROM THE SAME
TYP.
W5 MATERIAL AS THE CARRIER PIPE.

WRI
7. SPOOL SHALL NOT BE WELDED TO THE CARRIER
W3
PIPE UNTIL CONCRETE HAS ATTAINED THE REQUIRED
MINIMUM COMPRESSIVE STRENGTH.

THE
PIPE SLEEVE BACKING STRIP (50mm WIDE x 1.6mm THK.)

FULL PENETRATION GROOVE WELD 8. SLEEVE SHALL BE WELDED TO THE CARRIER PIPE
USING THE SAME ELECTRODES USED FOR WELDING

THOUT
THROUGHOUT THE LENGTH OF SLEEVE
CARRIER PIPE
THE CARRIER PIPE AT SPLICES.
TYP.
W7 SLEEVE TO SLEEVE
9. WHEN WELDING SLEEVES CARE SHALL BE TAKEN

WI
W2 WELD, (SEE NOTE 9)
TO AVOID BURNING THROUGH BACKING STRIP.
BACKING STRIP SHALL BE 1.6MMX50MM.
PIPE SLEEVE | WELDS

NG
DRAWI
38mm CHAMFER ON ° 10. THE ‚" VENT HOLE SHALL BE DRILLED AND TAPPED
45
ANCHOR FLANGE ON PIPE SLEEVE PRIOR TO WELDING THE SLEEVE
ANCHOR FLANGE TO THE CARRIER PIPE. HOLE SHALL SE SEALED
OUTLINE OF CONCRETE W6 SPLICE WITH MASTIC AFTER WELDING AND AIR TESTING OF
STIFFENERS ( NS & FS )

S
THI
ANCHOR BLOCK THE SLEEVE.

11. ALL SHOP FABRICATION DRAWINGS SHALL BE

ANCHOR FLANGE PLATE

FROM
REVIEWED AND APPROVED BY SAUDI ARAMCO
PRIOR TO FABRICATION UNLESS OTHERWISE NOTED.

END PLATE 12. DRAWING SHALL BE READ IN CONJUCTION WITH

NED
W/2

STIFFENER PLATE
SAUDI ARAMCO STANDARD DRAWING DA-220-002.
LENGTH)Ls

W4
SPOOL

(SEE CUTTING DIAGRAM)

OBTAI
S1
PLATE OUTSIDE DIAMETER (OD)
W)
PE

BE
PI
Lc

DTH

ANCHOR FLANGE
SLEEVE

|
B
ER

PART,SHALL
WI

SECTION A-A
CARRI

ANCHOR FLANGE

ON
PE

END PLATE

TI
PI

LEGEND

UC
(

9
W/2

01
TR

-2
ct
| CENTER LINE

-O
NS

N
09

I
P PLATE

CO
L

FULL,OR
R
STIFF STIFFENER

FO
TYP TYPICAL

ED
MIN MINIMUM

SU

N
I
65

IS
PT PLATE THICK
A A

ON
 
300

REPRODUCTI
(TYP.) 2NOS.-6mm NPT VENT HOLE (THREADED)

S1
W1
(SEE NOTE -10)

SAUDIARAMCO.NO
65
REFERENCE DRAWINGS
DWG. CONTROL FOR J.O. BI-10-01861 RD-663715
S2
CONSTRUCTION SCOPE OF WORK CE-663716
OVERALL PLOT PLAN NA-B42794
PLAN, SECTION & DETAIL-THRUST ANCHOR RA-663825

OF
STIFFENER PLATE
CUTTING DIAGRAM

PROPERTY
ANCHOR SLEEVE & FLANGE LAYOUT

SOLE
1 NO. REQD.

THE
ARE N
HEREI
0 0.5 1.0 1.5 2.0

METERS

NED
SCALE: 1 : 20M

CONTAI
ANCHOR FLANGE SCHEDULE REVISION VALIDATION

THIS REVISION NO. 00 IS COVERED, FOR ALL APPROVAL AND CERTIFICATION

REQUIREMENTS, PER SAEP-334, UNDER DRAWING COMPLETION CERTIFICATE NO:

D I M E N S I O N (MM) WELD CHART

ON
10-01861-0001-001
CARRIER PIPE SPOOL PIPE SLEEVE

NFORMATI
STIFFENER PLATE
ANCHOR ANCHOR FLANGE PLATE END PLATE LOCATION DESIGN CERTIFICATION REVIEW FOR KEY DRAWINGS OTHER
(PER FLANGE SIDE) WELD SIZE AND SYMBOL (USE E70 ELECTRODES) (DESIGN AGENCY) REQUIRED (SAUDI ARAMCO)
DRAWING
ENGG./DATE CERTIFIED BY/DATE CONST. AGENCY/DATE OPERATIONS/DATE BY/DATE
OD WT LC WT LS PT MAT AOO AOO AAA
ID OD UNIT S1 S2 PT B PT W1 W4 W2 W6 W7 W5 W3 08/25/19 08/25/19 08/25/19 08/25/19
(IN) (IN) (MM) (IN) (MM) (MM)
REV.NO. DATE REVISION DESCRIPTION

I
00 08/25/19 ISSUED FOR CONSTRUCTION

THE
SOUR WATER M JOB ORDER/EWO NO.
NA-B42794 THIS REVISION IS NOT TO BE USED FOR
6 0.28 3700 0.28 194 432 25 8 80 119 10 100 10
PIPE LINE 2500
8 6
3
8 6 10-01861-0001 CONSTRUCTION UNTIL CERTIFIED AND DATED
60° 60° 60°
SAUDI ARABIAN OIL COMPANY

AND
DRAWING TYPE

STRUCTURAL DETAIL SDT

NG
THRUST ANCHOR FOR 6" EGTL

DRAWI
FRACTIONATION & TREATING NGL CENTER

JU 'AYMAH SAUDI ARABIA

S
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.

THI
R84 M RA-663819 001 00
Saudi Aramco 2615 ENG. (05/05)

RESTRICTED VECTOR CADD-01