Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
62 views

Arduino - ParallelProgrammer

This document provides instructions for building a parallel port programmer to program Arduino boards without additional equipment, involving soldering resistors to a parallel port connector and cables to allow programming via the parallel port on a PC running Windows. The parallel port programmer allows burning the bootloader onto Arduino boards or direct programming using UISP, but does not enable communication between the PC and programs on the board which requires a serial cable.

Uploaded by

reyniel
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
62 views

Arduino - ParallelProgrammer

This document provides instructions for building a parallel port programmer to program Arduino boards without additional equipment, involving soldering resistors to a parallel port connector and cables to allow programming via the parallel port on a PC running Windows. The parallel port programmer allows burning the bootloader onto Arduino boards or direct programming using UISP, but does not enable communication between the PC and programs on the board which requires a serial cable.

Uploaded by

reyniel
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

arduino.

cc

Arduino - ParallelProgrammer

3-4 minutos

Parallel Port Programmer


Instructions for building a parallel port programmer for the
Arduino board (or any other Atmega8 chip). Allows you to
program the board on Windows without any additional equipment.
Cheap and fun. (Please note, however, that this doesn't allow for
communication between the computer and programs running on
the board. You'll need a serial cable for that.)

Rear view of connector.

Equipment

Tools:

Soldering iron
Hot glue gun (optional)
You'll need (parts):

(2x) 470 ohm resistor (yellow-purple-brown)


(1x) 220 ohm resistor (red-red-brown)
(1x) parallel port cable or parallel-to-serial adapter
(2x) three wire cables with female connectors on one end,
unattached wires on the other

Instructions

Remove any existing wires from the parallel connector.

Solder 470 ohm resistors to pins 1 and 2 of the parallel connector.


Parallel connector with a 470 ohm resistor soldered to pin 1.

Solder a 220 ohm resistor to pin 11 of the connector.

Solder, in order, the three wires of one of the cables to the resistor
on pin 11 (which goes to pin 18 on the Atmega8), to the resistor
on pin 1 (which goes to pin 19 on the Atmega8), and directly to pin
16 (which goes to the reset, pin 1).

Parallel connector with two of the three wires of a cable soldered to


pins 11 and 1, respectively.

Solder the middle wire of the second cable to the resistor on pin 2
(which goes to pin 17 on the Atmega8), and one of the other wires
to pin 18 (which goes to ground). (The third wire is not used and
may be cut short).

Parallel connector with both cables soldered in place.

Connect the ends of the two cables so that, when viewed from the
connector end, the unused wire is to the upper left and the wire to
pin 11 is to the upper right (this is considered pin 1 of the
connector and should be matched with the pin 1 indicated on the
Arduino board).

Hot glue the wires inside the case of the parallel-to-serial


adapater, making sure that any uninsulated wires are kept apart.
Or, if not using an adapter, wrap the exposed wires with electrical
tape to keep them from touching.
Once the glue dries, reclose the case of the parallel-to-serial
adapter.

Software

You'll need to download giveio.

See the bootloader page for details on using your new parallel
port programmer to burn the bootloader onto the Arduino board.

Or, if you're programming using uisp directly, you can use a


command line like:
uisp -dprog=dapa -dpart=ATmega8 if=prog.hex -dlpt=0x378
--erase --upload

@author: David A. Mellis IDII (with thanks to Erez Kikin-Gil for


building one too and to Massimo Banzi for the request and the
instructions)

@revised by: Marcos Yarza K3

You might also like