Product Range & Price Guide: Effective From January 2012

Product Range
& Price Guide

Effective from January 2012
Energy Efficiency
We recommend that filter elements are replaced at least every 12 months
(6 months for activated carbon) in order to maintain the optimum
performance of your system. Every 1 barg (100kPa) of pressure drop represents
a 7% increase in compressor energy costs. It is vital to observe a scheduled
maintenance programme which includes replacement of filter elements.
In any compressed air system, impurities are inevitable as the quality of your compressed
air is only as good as the intake air. Dust, oil and particulates reduce air quality and
can significantly affect the system efficiency, including the performance and life of the
end-use equipment. Poor system efficiency also means higher running costs.
Filtration and treatment of your compressed air system is critical to:
Guarantee optimum performance

Ensure energy costs are minimised
Water condensate is also a significant problem which needs to be removed in order to

achieve optimum performance. A single 30kW compressor can generate 20 litres of
water in 8 hours from the condensation of the air during the compression process.
Minimising waste and maximising air treatment offers the greatest potential for cost
savings in a typical compressed air system.
Price Guide effective from 1st January 2012.

All prices within the Walker Filtration Price Guide
exclude VAT and carriage.
We accept the following payments.
contents
page
General Information Correction Factors 4
Conversion Tables 5
Compressed Air Quality 6
Compressed Air Standards 7
Alpha Series Filters & Elements 8-11
Compressed Air Filters Water Separators 12

X25 Coarse Filtration 13
X5 Medium Filtration 14
X1 Fine Filtration 15
XA High Efficiency Filtration 16
AC Activated Carbon Filtration 17
XAC 2 Stage Duplex Filtration 18
Dust Filtration 19
High Temperature Dust Filtration 20
Alloy High Pressure Filters, 20 barg (300 psig) 21
Alloy High Pressure Filters, 50 barg (725 psig) 22
Stainless Steel High Pressure Filters 23
Medical Sterile Filters 24
Autoclave Filter Elements 25
Vacuum Pump Protection Filters 26
Vacuum Pump Exhaust Filters 27
Odasorb Exhaust Filters 28
Medical Vacuum Filters 29
Ammonia & Refrigerant Filters 30
Heater & Filter Heater Packages 31
Breathing & Medical Air 32
Breathable Compressed Air 33
Compressed Air Dryers Pro Dry 35

and Adsorption Systems Pro Dry Accessories 36-37
Accessories Drain Valve Equipment 39

Differential Pressure Equipment 40
Accessories 41-42
Filter Elements Previous Walker Filter Elements 43

& Alternative Filter Elements Alternative Filter Elements & 44-70
Vacuum Pump Separators
Conditions of Trade 71
3
correction factors
pressure for maximum flow rate, multiply model flow rate
by the correction factor corresponding to the pressure
Operating pressure barg (psig) 0.3 (4) 0.6 (9) 1 (14.5) 2 (29) 3 (44) 4 (58) 5 (72) 6 (87) 7 (100) 8 (115) 10 (145) 12 (174) 14 (203) 16 (232)
7 barg Correction factor 0.21 0.29 0.38 0.53 0.65 0.76 0.84 0.92 1.00 1.07 1.19 1.31 1.41 1.51
Operating pressure barg (psig) 4 (58) 6 (87) 8 (116) 10 (145) 12 (174) 14 (203) 16 (232) 18 (261) 20 (290)
20 barg Correction factor 0.45 0.55 0.63 0.71 0.77 0.84 0.90 0.95 1.00
Operating pressure barg (psig) 50 (725) 100 (1450) 150 (2175) 200 (2900) 250 (3625) 300 (4350) 350 (5000)
350 barg Correction factor 0.73 0.78 0.82 0.87 0.91 0.96 1.00
vacuum for maximum flow rate, multiply model flow rate

by the correction factor corresponding to the working vacuum
Operating vacuum mbar abs atmospheric 900 800 700 600 500 400 300 200
Torr 760 675 600 525 450 375 300 225 150
psia 14.7 13.0 11.6 10.2 8.7 7.3 5.8 3.3 2.9
Correction factor 1.00 0.93 0.86 0.79 0.71 0.64 0.57 0.50 0.43
dryers
Operating temperature °C (°F) 20 (68) 25 (77) 30 (86) 35 (95) 40 (104) 45 (113) 50 (122)
Correction factor 0.62 0.75 0.87 1.00 1.12 1.37 1.62
Dewpoint °C (°F) -40 (-40) -70 (-94)

Correction factor 1.00 0.70
general notes
technical notes
1 Threaded and duplex filter housings are suitable for temperatures up to 120°C (248°F).
2 Threaded and duplex filters are manufactured from cast aluminium alloy and are PED 97/23/EC compliant for group 2 gases and carry the CE mark where applicable.
3 Flanged filters are fabricated from carbon steel and carry the CE mark where applicable.
4 Threaded connections are Rp (BSP parallel) to ISO 7/1 or NPT to ANSI B2.1 if supplied within North America, with the following exceptions 50HP25 and
50HP37 are Rc (BSP Taper); 100HP24, 100HP49, 350HP24 and 350HP26 are NPT. Flanged connections are complete with mating flanges to BS4504, PN16.
5 For NPT connections, add the suffix NPT e.g. A018 XA - NPT.
6 Flanged vessels are designed and manufactured in accordance with BS EN286 Part 1 and meet the Simple Pressure Vessels Directive.
7 Cross port dimensions on flanged vessels are subject to a manufacturing tolerance of +/- 3mm and a squareness tolerance of 1 degree.
8 Filter elements should be changed every 12 months / 8000 hours (whichever comes first). Activated carbon filter elements should be changed every
6 months / 1000 hours (whichever comes first).
9 Filters and water separators are suitable for use with mineral and synthetic oils, plus oil-free compressed air applications.
10 Dimension 'D' in general arrangement drawings refers to bowl clearance required for element change.
11 Mounting brackets are available for various filters, see page 42.
12 Silicone free options are available, please contact Sales for details.
13 All ppm references are ppm by mass.
4 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
email sales@walkerfiltration.co.uk web www.walkerfiltration.com
conversion tables
convert pressure
(multiplying factors)
from to psi inH20 mmHg atmos mbar bar Kgf/cm² Pascal kPa MPa
  (lbf/in²) (Torr) (Kp/cm²) (N/m²) (kN/m²) MN/m² (N/mm²)
psi (lbf/in2) 1 27.6799 51.7149 0.068046 68.9476 0.06895 0.070307 6894.76 6.89476 0.0068948
inH20 0.036127 1 1.86832 0.0024583 2.49089 0.00249 0.00254 249.089 0.24901 0.000249
mmHg (Torr) 0.019337 0.53524 1 0.0013158 1.33322 0.00133 0.0013591 133.322 0.13332 0.000133
atmos 14.6959 406.781 760 1 1013.25 1.01325 1.03323 101,325 101.325 0.101325
mbar 0.014504 0.401463 0.750062 0.0009869 1 0.001 0.0010197 100 0.1 0.0001
bar 14.504 401.463 750.062 0.9869 1000 1 1.0197 100,000 100 0.1
Kgf (Kp/cm²) 14.2233 393.7 735.556 0.967841 980.665 0.980665 1 98066.5 98.0665 0.09806
Pascal (N/m²) 0.000145 0.004015 0.007501 0.0000099 0.01 0.00001 0.0000102 1 0.001 0.00001
kPa 0.14504 4.015 7.501 0.0099 10 0.01 0.0102 1000 1 0.001
MPa 145.04 4015 7501 9.9 10000 10 1.02 1,000,000 1000 1
convert flow rate

(multiplying factors)
from to litre/sec dm³/sec litre/min m³/sec m³/min Nm³/hr SCFM
 
litre/sec 1 1 60 0.001 0.06 3.6 2.118882
dm³/sec 1 1 60 0.001 0.06 3.6 2.118882
litre/min 0.016667 0.0166667 1 0.00001667 0.001 0.06 0.035315
m³/sec 1000 1000 60,000 1 60 3600 2118.88
m³/min 16.66667 16.66667 1000 0.0166667 1 60 35.315
Nm³/hr 0.277778 0.277778 16.66667 0.000278 0.0166667 1 0.588578
SCFM 0.471947 0.471947 28.31682 0.000472 0.0283168 1.699 1
recommended air flow rate
Nominal bore at main line velocity of 6 m/s at branch line velocity of 15 m/s
mm inch dm3/s (l/s) SCFM dm3/s (l/s) SCFM
6 /
1 8 1 2 3 6
8 ¼ 3 6 8 17
10 5 11 12 25
15 ½ 10 21 25 53
20 ¾ 17 36 40 85
25 1 25 53 60 127
32 1¼ 50 106 125 265
40 1½ 65 138 160 339
50 2 100 212 250 530
65 2½ 180 382 450 954
80 3 240 509 600 1272
100 4 410 869 - -
125 5 610 1293 - -
150 6 900 1908 - -
200 8 1600 3392 - -
250 10 2500 5300 - -
300 12 3600 7632 - -
BS 4575 Maximum Recommended Air Flow Rates at 7 barg (100 psig)

This standard gives guidance and recommendations to designers, manufacturers and users for what are considered to be
minimum essential features of the design and construction of fluid power systems and components. BS ISO 4414:1998
(not equivalent) closely follows the recommendations of ISO 4414 and the table above is based on that standard.
Note: Walker Filtration provide these conversion charts as a guide only.
5
compressed air quality
Compressed air purity classes ISO 8573-1
The ISO 8573 group of International Standards is used for the classification of
compressed air. It also provides the test methods and analytical techniques for each
PURITY CLASSIFICATION type of contaminant.
The table below summarises the maximum contaminant levels specified in ISO 8573
solid particles
water
Part 1 (2010) for the various compressed air quality classes.
Each compressed air classification can be achieved by installing a specific filter grade
oil or a combination of filter grades, depending upon required performance.
Particles Water Oil

Maximum number of particles per cubic metre as a Vapour Liquid a Total Oil a
function of particle size, d a
Purity Class Mass Pressure Concentration Liquid, aerosol,
Concentration Liquid Water
0.1μm < d ≤ 0.5μm 0.5μm < d ≤ 1.0μm 1.0μm < d ≤ 5.0μm Dewpoint vapour
Cp Cw
°C mg/m³
mg/m³ g/m³
0 As specified by the equipment user or supplier and more stringent than Class 1
1 ≤ 20 000 ≤ 400 ≤ 10 - ≤-70 - ≤ 0.01
2 ≤ 400 000 ≤ 6 000 ≤ 100 - ≤-40 - ≤ 0.1
3 - ≤ 90 000 ≤ 1 000 - ≤-20 - ≤1
4 - - ≤ 10 000 - ≤ +3 - ≤5
5 - - ≤ 100 000 - ≤ +7 - -
6 - - - 0 < Cp ≤ 5 ≤ +10 - -
7 - - - 5 < Cp ≤ 10 - Cw ≤ 0.5 -
8 - - - - - 0.5 < Cw ≤ 5 -
9 - - - - - 5 < Cw ≤ 10 -
X - - - Cp > 10 - Cw > 10 >5
a
At reference conditions, 100kPa (1 bar(a)), 20°C, 0 Relative water vapour pressure (0% relative humidity)
Filter Grade GRADE X25 GRADE X5 GRADE X1 GRADE XA GRADE AC
Maximum particle size class to ISO 8573-1:2010 - Class 3 Class 2 Class 1 Class 1
Maximum oil content class to ISO 8573-1:2010 - Class 4 Class 2 Class 1 Class 1
3,-,4
Medium filtration
Bulk liquid and medium filtration especially
designed for the removal of high
concentrations of oil which contain burnt
by-products such as lacquers.
Compressor Air WS X5
receiver
High Efficiency Filtration 1,2,1

High efficiency sub-micron filtration to provide
oil/particulate free compressed air. This filter
package offers protection to adsorption dryers
and provides the user with the best possible
compressed air quality.
Compressor Air WS X1 XA RXA XAC
receiver
6 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
compressed air standards
Walker Filtration filters and dryers are designed to meet the needs of a wide range
of industries. The range aims to address the compressed air purity requirements of
almost any application. Product performance is tested and validated in accordance
with the latest international standards, of which the main ones are outlined below.
ISO 8573 - compressed air purity standard

ISO 8573 group of International Standards comprises of nine parts, which provide
classifications for the main contaminants in compressed air, and the test methods
and qualitative analysis used in the determination process.
ISO 8573-1 Contaminants and Purity classes
ISO 8573-2 Test Methods for Oil Aerosol Content
ISO 8573-3 Test Methods for the Measurement of Humidity
ISO 8573-4 Test Methods for the Solid Particle Content
ISO 8573-5 Test Methods for Oil Vapour and Organic Solvent Content
ISO 8573-6 Test Methods for Gaseous Contaminant Content
ISO 8573-7 Test Methods for Viable Microbiological Contaminant Content
ISO 8573-8 Test Methods for Solid Particle Content by Mass Concentration
ISO 8573-9 Test Methods for Liquid Water Content
ISO 12500 - introducing a new series of international

standards for compressed air filter testing
The ISO 12500 is a new group of standards for compressed air filter testing and
has been introduced to complement the existing ISO 8573 series.
ISO 12500-1 Oil Aerosols
ISO 12500-2 Oil Vapours
ISO 12500-3 Particles
ISO 12500-4 Water
Other Applicable Standards

ISO 7183 Compressed-air dryers – Specifications and testing
This standard identifies the required test methods for measuring dryer performance
parameters for different types of compressed air dryers which includes: pressure
dewpoint, flow rate, pressure drop, compressed air loss, power consumption and
noise emission methods.
7
8
alpha series
filters & elements
Introducing the next generation
The technologically advanced design

boasts enhanced housing and element
performance. It is also specifically
developed for ease of installation and
maintenance for engineers.
This extended range of filter housings
and elements has been designed to suit
almost every industrial environment.
Advancements in leak reduction and
enhanced custom filter media deliver
improved filtration performance. This
means you get reduced pressure loss,
increased energy efficiency levels and
lower energy costs.
Tested to ISO 12500 standards, this
filter range has been independently
validated to guarantee the highest levels
of air quality, making the Alpha Series
your ultimate filtration solution.
9
alpha series filters & elements
Filter Element Features
Double O-ring secures against

contaminant by-pass
Perforated stainless steel cylinders
provide strength, rigidity and corrosion
resistance
Spiral wound, inner spring on larger
size elements for extra strength
Deep bed filter media provides low
operating differential pressure resulting
in improved energy efficiency
Hydrophobic and oleophobic
borosilicate customised glass fibre
media for improved coalescing
Unique anti re-entrainment layer
minimises pressure losses and improves
liquid removal
Bespoke chemically treated outer
drainage layer prevents oil carry over
New improved ultrasonic seam
weld process provides greater strength
Air distribution duct gives uniform
air flow for improved filtration and low
operating differential pressure
Drop-fit, self locating element with
no tie rods for ease of installation,
servicing and maintenance
Corrosion resistant colour coded
endcaps for easy and accurate filtration
grade indication
Lower annular location ring

prevents element vibration, improves
stability in reverse flow dust removal
applications and improves drainage
Certificate of Conformity supplied
with every filter element
10 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Secure thread to bowl connection
with full 3 turns to ensure safety
Unique seal configuration ensures
security of the pressure envelope
Large reservoir to provide quiet zone
for bulk oil collection
Automatic drain with manual
Filter Housing Features override fitted as standard
Hexagon spanner locator for
simple bowl removal
Extensive range –¼” to 3”
(BSP & NPT) and flow capacities Minimal clearance required for filter
up to 2550 Nm3/hr change and no specialist tools
Compact design allowing installation Suitable for both mineral and
in confined spaces synthetic oils
Modular design enables easy and
simple close coupling assembly
Aluminium pressure die cast
housing gives enhanced strength and
robustness
Advanced E-coat protection with a
polyester coating gives exceptional
corrosion resistance
11
COMPRESSED AIR FILTERS
For compressed air installations where water contamination is a problem,

Walker Filtration manufactures a range of water separators which utilise an internal
centrifugal module to remove large quantities of condensate.
WS water separators
filter pipe flow rate dimensions (mm) weight complete
model size Nm³/h SCFM A B C D Kg price
JANUARY 2012
A028 WS ¼ 42 25 70 25 191 90 0.7

A038 WS 59 35 70 25 191 90 0.7
A058 WS ½ 85 50 70 25 191 90 0.7
A059 CWS ½ 119 70 100 35 210 90 0.7
A059 WS ½ 119 70 100 35 276 110 1.5
A078 WS ¾ 212 125 100 35 276 110 1.5
A108 WS 1 297 175 100 35 276 110 1.5
* The CWS range has a shorter bowl for compact installations
A128 CWS 1¼ 476 280 122 42 380 150 2.3

A128 WS 1¼ 476 280 122 42 460 150 2.5
A158 CWS 1½ 545 320 122 42 380 150 2.3
A158 WS 1½ 545 320 122 42 460 150 2.5
A159 WS 1½ 680 400 146 52 482 180 4
A208 WS 2 1189 700 146 52 482 180 4
A254 WS 2½ 1445 850 210 67 595 200 8.5
A340 WS 3 2549 1500 210 67 595 200 8.5
A391 WS DN80 2160 1270 450 265 1205 n/a 58
A400 WS DN100 3100 1824 520 285 1245 n/a 74
A600 WS DN150 6500 3824 680 400 1400 n/a 165
A800 WS DN200 11000 6470 780 400 1460 n/a 260
A1000 WS DN250 17000 10000 900 550 1570 n/a 450
A1200 WS DN300 25500 15000 900 600 1620 n/a 550
A A Replacements and spare parts (refer to pages 38 – 42)

B
B
C C
30mm Float operated drain valve

approx.
A018 to A058 order DVAS16C
D A059 to A390 order DVAS16
D
A028 WS to A391 WS to
A340 WS A1200 WS
specification flanged filter packaging
Grade WS Model numbers Packaging price
Maximum recommended operating temperature 120°C 248°F A391WS, A391 (grade), A400WS, £50.00
Minimum recommended operating temperature 1.5°C 35°F A483 (grade), A484 (grade)
Maximum working pressure 16 barg 232 psig A600WS, A686 (grade), £80.00
A688 (grade)
A800WS, A8810 (grade) £125.00
A1000WS, A10816 (grade) £200.00
A1200WS, A12824 (grade) £250.00
* The above table is for EN286 pressure vessel with DN PN16 flanges.
* For EN286 pressure vessel with ANSI flanges please add an additional 10%.
* Price on application for ASME standard vessels.
technical notes
1 Water separators are fitted with float operated automatic drain valves. DVAS16C on models A028 WS to A058
WS and DVAS16 on models A059 WS to A340 WS . When high quantities of liquid are anticipated, Walker
Filtration recommend the use of electronic drain valves. ½" manual drain valves are fitted to A391 WS to A800
WS, ¾" fitted to A1000 WS to A1200 WS as standard.
2 An additional ½" side entry port is included on models A391 WS to A800 WS, ¾" for A1000 WS and A1200 WS.
3 A connecting kit is required to connect a water separator to filter models A028 to A340.
12 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
For heavy duty applications, alpha series grade X25 micron threaded filter range
removes high concentrations of dirt and liquid from compressed air.
coarse filtration X25

filter pipe flow rate dimensions (mm) weight complete element element no. of
model size Nm³/h SCFM A B C D Kg price model price elements
JANUARY 2012
A018 X25 ¼ 13.6 8 50 18 152 60 0.3 E0304 X25 1
A019 X25 ¼ 25.5 15 50 18 152 60 0.3 E0305 X25 1
A028 X25 ¼ 42.5 25 70 65 231 70 0.6 E0406 X25 1
A038 X25 59.5 35 70 65 231 70 0.6 E0407 X25 1
A058 X25 ½ 85.0 50 70 65 272 70 0.7 E0413 X25 1
A059 X25 ½ 119 70 100 105 346 80 1.6 E0613 X25 1
A078 X25 ¾ 144 85 100 105 346 80 1.6 E0613 X25 1
A079 X25 ¾ 212 125 100 105 466 80 2.0 E0620 X25 1
A108 X25 1 229 135 100 105 466 80 2.0 E0620 X25 1
A109 X25 1 297 175 100 105 466 80 2.0 E0625 X25 1
A128 X25 1¼ 476 280 122 112 530 80 2.8 E0730 X25 1
A158 X25 1½ 545 320 122 112 530 80 2.8 E0730 X25 1
A159 X25 1½ 680 400 146 122 552 100 4.2 E0830 X25 1
A208 X25 2 765 450 146 122 552 100 4.2 E0830 X25 1
A209 X25 2 1190 700 146 122 855 100 6.3 E0860 X25 1
A254 X25 2½ 1445 850 210 137 665 100 8.5 E1140 X25 1
A340 X25 3 1530 900 210 137 665 100 8.5 E1140 X25 1
A360 X25 3 2125 1250 210 137 885 100 10.5 E1160 X25 1
A390 X25 3 2550 1500 210 137 1045 100 12.0 E1175 X25 1
See page 12 for flanged filter packaging
A391 X25 DN80 2160 1270 450 265 1205 700 58 E139 X25 1
A483 X25 DN100 3100 1824 520 285 1245 700 74 E88 X25 3
A484 X25 DN100 4250 2500 520 285 1245 700 74 E88 X25 4
A686 X25 DN150 6500 3824 680 400 1400 700 165 E88 X25 6
A688 X25 DN150 8720 5130 780 400 1430 700 208 E88 X25 8
A8810 X25 DN200 11000 6470 780 400 1460 700 260 E88 X25 10
A10816 X25 DN250 17000 10000 900 550 1570 700 450 E88 X25 16
A12824 X25 DN300 25500 15000 900 600 1620 700 740 E88 X25 24
Replacements and spare parts (refer to pages 38 – 42)

A A
B
B
C C
X25 element Differential Float operated drain valve

pressure gauge A018 to A058 order DVAS16C 30mm
65DPIG A059 to A390 order DVAS16 approx.
D
D
technical notes
Direction of air flow is inside to out through the filter 1 A018 X25 to A391 X25 to
element. A390 X25 A12824 X25
Pop up indicators (65DPUG) are fitted to models
A028 X25 to A058 X25 as standard. Differential pressure
2 specification
indicators (65DPIG) are fitted to models A059 X25 to
A12824 X25 as standard. Grade X25
Threaded filters are fitted with float operated automatic 3 Maximum particle size class to ISO 8573-1:2010 -
drain valves. DVAS16C on models A018 X25 to A058 X25 Maximum oil content class to ISO 8573-1:2010 -
and DVAS16 on models A059 X25 to A390 X25. Flanged
Particle removal 25 micron
filters are fitted with manual drain valves. On models
A391 X25 to A8810 X25, ½" are fitted; ¾" on models Maximum oil carryover at 20°C (68°F) 10 mg/m³ 8.2 ppm
A10816 X25 to A12824 X25. Maximum temperature up to 120°C up to 248°F
Models A059 X25 to A390 X25 can be adapted to use 4 Maximum working pressure 16 barg 232 psig
¼" drains with a reducer.
Element end cap colour black
An additional ½" side entry port is included on models 5
A391 X25 to A8810 X25, ¾" for A10816 X25 and
A12824 X25.
13
The range of alpha series grade X5 micron coalescing filters are used for removing
high concentrations of oil from compressed air.
X5 medium filtration
model size Nm3/h SCFM A B C D Kg price model price elements
JANUARY 2012
A018 X5 ¼ 13.6 8 50 18 152 60 0.3 E0304 X5 1

A019 X5 ¼ 25.5 15 50 18 152 60 0.3 E0305 X5 1
A028 X5 ¼ 42.5 25 70 65 231 70 0.6 E0406 X5 1
A038 X5 59.5 35 70 65 231 70 0.6 E0407 X5 1
A058 X5 ½ 85.0 50 70 65 272 70 0.7 E0413 X5 1
A059 X5 ½ 119 70 100 105 346 80 1.6 E0613 X5 1
A078 X5 ¾ 144 85 100 105 346 80 1.6 E0613 X5 1
A079 X5 ¾ 212 125 100 105 466 80 2.0 E0620 X5 1
A108 X5 1 229 135 100 105 466 80 2.0 E0620 X5 1
A109 X5 1 297 175 100 105 466 80 2.0 E0625 X5 1
A128 X5 1¼ 476 280 122 112 530 80 2.8 E0730 X5 1
A158 X5 1½ 545 320 122 112 530 80 2.8 E0730 X5 1
A159 X5 1½ 680 400 146 122 552 100 4.2 E0830 X5 1
A208 X5 2 765 450 146 122 552 100 4.2 E0830 X5 1
A209 X5 2 1190 700 146 122 855 100 6.3 E0860 X5 1
A254 X5 2½ 1445 850 210 137 665 100 8.5 E1140 X5 1
A340 X5 3 1530 900 210 137 665 100 8.5 E1140 X5 1
A360 X5 3 2125 1250 210 137 885 100 10.5 E1160 X5 1
A390 X5 3 2550 1500 210 137 1045 100 12.0 E1175 X5 1

A391 X5 DN80 2160 1270 450 265 1205 700 58 E139 X5 1
A483 X5 DN100 3100 1824 520 285 1245 700 74 E88 X5 3
A484 X5 DN100 4250 2500 520 285 1245 700 74 E88 X5 4
A686 X5 DN150 6500 3824 680 400 1400 700 165 E88 X5 6
A688 X5 DN150 8720 5130 780 400 1430 700 208 E88 X5 8
A8810 X5 DN200 11000 6470 780 400 1460 700 260 E88 X5 10
A10816 X5 DN250 17000 10000 900 550 1570 700 450 E88 X5 16
A12824 X5 DN300 25500 15000 900 600 1620 700 740 E88 X5 24

A A
B
B
C C

30mm pressure gauge A018 to A058 order DVAS16C
approx. 65DPIG A059 to A390 order DVAS16
D
D
technical notes
A018 X5 to A391 X5 to 1 Direction of air flow is inside to out through the filter
element.
A390 X5 A12824 X5
2 Pop up indicators (65DPUG) are fitted to models A028 X5
specification to A058 X5 as standard. Differential pressure indicators
(65DPIG) are fitted to models A059 X5 to A12824 X5.
Grade X5 3 Threaded filters are fitted with float operated automatic
drain valves. DVAS16C on models A018 X5 to A058 X5
Maximum particle size class to ISO 8573-1:2010 3
and DVAS16 on models A059 X5 to A390 X5. Flanged
Maximum oil content class to ISO 8573-1:2010 4 filters are fitted with manual drain valves. On models
Particle removal 5 micron A391 X5 to A8810 X5, ½" are fitted; ¾" on models
A10816 X5 to A12824 X5.
Maximum oil carryover at 20°C (68°F) 5 mg/m3 4.1 ppm
4 Models A059 X5 to A390 X5 can be adapted to use ¼"
Maximum temperature up to 120°C up to 248°F drains with a reducer.
Maximum working pressure 16 barg 232 psig 5 An additional ½" side entry port is included on models
Element end cap colour green A391 X5 to A8810 X5, ¾" for A10816 X5 and
A12824 X5.
14 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Alpha series grade X1 micron removes liquids, particles and coalesced oil aerosols
down to 0.1 mg/m³.
fine filtration X1
JANUARY 2012
A018 X1 ¼ 13.6 8 50 18 152 60 0.3 E0304 X1 1
A019 X1 ¼ 25.5 15 50 18 152 60 0.3 E0305 X1 1
A028 X1 ¼ 42.5 25 70 65 231 70 0.6 E0406 X1 1
A038 X1 59.5 35 70 65 231 70 0.6 E0407 X1 1
A058 X1 ½ 85.0 50 70 65 272 70 0.7 E0413 X1 1
A059 X1 ½ 119 70 100 105 346 80 1.6 E0613 X1 1
A078 X1 ¾ 144 85 100 105 346 80 1.6 E0613 X1 1
A079 X1 ¾ 212 125 100 105 466 80 2.0 E0620 X1 1
A108 X1 1 229 135 100 105 466 80 2.0 E0620 X1 1
A109 X1 1 297 175 100 105 466 80 2.0 E0625 X1 1
A128 X1 1¼ 476 280 122 112 530 80 2.8 E0730 X1 1
A158 X1 1½ 545 320 122 112 530 80 2.8 E0730 X1 1
A159 X1 1½ 680 400 146 122 552 100 4.2 E0830 X1 1
A208 X1 2 765 450 146 122 552 100 4.2 E0830 X1 1
A209 X1 2 1190 700 146 122 855 100 6.3 E0860 X1 1
A254 X1 2½ 1445 850 210 137 665 100 8.5 E1140 X1 1
A340 X1 3 1530 900 210 137 665 100 8.5 E1140 X1 1
A360 X1 3 2125 1250 210 137 885 100 10.5 E1160 X1 1
A390 X1 3 2550 1500 210 137 1045 100 12.0 E1175 X1 1
A391 X1 DN80 2160 1270 450 265 1205 700 58 E139 X1 1

A483 X1 DN100 3100 1824 520 285 1245 700 74 E88 X1 3
A484 X1 DN100 4250 2500 520 285 1245 700 74 E88 X1 4
A686 X1 DN150 6500 3824 680 400 1400 700 165 E88 X1 6
A688 X1 DN150 8720 5130 780 400 1430 700 208 E88 X1 8
A8810 X1 DN200 11000 6470 780 400 1460 700 260 E88 X1 10
A10816 X1 DN250 17000 10000 900 550 1570 700 450 E88 X1 16
A12824 X1 DN300 25500 15000 900 600 1620 700 740 E88 X1 24

A A
B
B
C C

pressure gauge A018 to A058 order DVAS16C 30mm
65DPIG A059 to A390 order DVAS16 approx.
D
D
technical notes
Direction of air flow is inside to out through the filter 1 A018 X1 to A391 X1 to
element. A390 X1 A12824 X1
Pop up indicators (65DPUG) are fitted to models A028 X1 2 specification
to A058 X1 as standard. Differential pressure indicators
(65DPIG) are fitted to models A059 X1 to A12824 X1. Grade X1
Threaded filters are fitted with float operated automatic 3
drain valves. DVAS16C on models A018 X1 to A058 X1
and DVAS16 on models A059 X1 to A390 X1. Flanged Maximum oil content class to ISO 8573-1:2010 2
filters are fitted with manual drain valves. On models Particle removal 1 micron
A391 X1 to A8810 X1, ½" are fitted; ¾" on models
Maximum oil carryover at 20°C (68°F) 0.1 mg/m³ 0.08 ppm
A10816 X1 to A12824 X1.
Models A059 X1 to A390 X1 can be adapted to use ¼" 4 Maximum temperature up to 120°C up to 248°F
drains with a reducer. Maximum working pressure 16 barg 232 psig
An additional ½" side entry port is included on models 5 Element end cap colour red
A391 X1 to A8810 X1, ¾" for A10816 X1 and
A12824 X1.
15
Alpha series grade XA filtration removes liquids, sub micron particles and oil aerosols
down to 0.01 mg/m3. It is most often used at point of use applications to provide
the highest level of filtration.
XA high efficiency filtration

model size Nm3/h SCFM A B C D Kg price model price elements
JANUARY 2012
A018 XA ¼ 13.6 8 50 18 152 60 0.3 E0304 XA 1

A019 XA ¼ 25.5 15 50 18 152 60 0.3 E0305 XA 1
A028 XA ¼ 42.5 25 70 65 231 70 0.6 E0406 XA 1
A038 XA 59.5 35 70 65 231 70 0.6 E0407 XA 1
A058 XA ½ 85.0 50 70 65 272 70 0.7 E0413 XA 1
A059 XA ½ 119 70 100 105 346 80 1.6 E0613 XA 1
A078 XA ¾ 144 85 100 105 346 80 1.6 E0613 XA 1
A079 XA ¾ 212 125 100 105 466 80 2.0 E0620 XA 1
A108 XA 1 229 135 100 105 466 80 2.0 E0620 XA 1
A109 XA 1 297 175 100 105 466 80 2.0 E0625 XA 1
A128 XA 1¼ 476 280 122 112 530 80 2.8 E0730 XA 1
A158 XA 1½ 545 320 122 112 530 80 2.8 E0730 XA 1
A159 XA 1½ 680 400 146 122 552 100 4.2 E0830 XA 1
A208 XA 2 765 450 146 122 552 100 4.2 E0830 XA 1
A209 XA 2 1190 700 146 122 855 100 6.3 E0860 XA 1
A254 XA 2½ 1445 850 210 137 665 100 8.5 E1140 XA 1
A340 XA 3 1530 900 210 137 665 100 8.5 E1140 XA 1
A360 XA 3 2125 1250 210 137 885 100 10.5 E1160 XA 1
A390 XA 3 2550 1500 210 137 1045 100 12.0 E1175 XA 1

A391 XA DN80 2160 1270 450 265 1205 700 58 E139 XA 1
A483 XA DN100 3100 1824 520 285 1245 700 74 E88 XA 3
A484 XA DN100 4250 2500 520 285 1245 700 74 E88 XA 4
A686 XA DN150 6500 3824 680 400 1400 700 165 E88 XA 6
A688 XA DN150 8720 5130 780 400 1430 700 208 E88 XA 8
A8810 XA DN200 11000 6470 780 400 1460 700 260 E88 XA 10
A10816 XA DN250 17000 10000 900 550 1570 700 450 E88 XA 16
A12824 XA DN300 25500 15000 900 600 1620 700 740 E88 XA 24

A A
B
B
C C
XA element Differential Float operated drain valve

30mm
pressure gauge A018 to A058 order DVAS16C
approx. 65DPIG A059 to A390 order DVAS16
D
D
A018 XA to A391 XA to technical notes

A390 XA A12824 XA 1 Direction of air flow is inside to out through the
specification filter element.
2 Pop up indicators (65DPUG) are fitted to models A028 XA
Grade XA to A058 XA as standard. Differential pressure indicators
(65DPIG) are fitted to models A059 XA to A12824 XA.
3 Threaded filters are fitted with float operated automatic
Maximum oil content class to ISO 8573-1:2010 1 drain valves. DVAS16C on models A018 XA to A058 XA
Particle removal 0.01 micron and DVAS16 on models A059 XA to A390 XA. Flanged
Maximum oil carryover at 20°C (68°F) 0.01 mg/m3 0.01 ppm filters are fitted with manual drain valves. On models
A391 XA to A8810 XA, ½" are fitted; ¾" on models
Maximum temperature up to 120°C up to 248°F A10816 XA to A12824 XA.
Maximum working pressure 16 barg 232 psig 4 Models A059 XA to A390 XA can be adapted to use ¼"
Element end cap colour blue drains with a reducer.
5 An additional ½" side entry port is included on models
A391 XA to A8810 XA, ¾" for A10816 XA and
A12824 XA.
16 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Alpha series grade AC removes odours and tastes from the compressed air supply
and provides further oil removal including vapour down to 0.003 mg/m³.
activated carbon filtration AC

JANUARY 2012
A018 AC ¼ 13.6 8 50 18 152 60 0.3 E0304 AC 1
A019 AC ¼ 25.5 15 50 18 152 60 0.3 E0305 AC 1
A028 AC ¼ 42.5 25 70 25 191 70 0.6 E0406 AC 1
A038 AC 59.5 35 70 25 191 70 0.6 E0407 AC 1
A058 AC ½ 85.0 50 70 25 232 70 0.7 E0413 AC 1
A059 AC ½ 119 70 100 35 276 80 1.6 E0613 AC 1
A078 AC ¾ 144 85 100 35 276 80 1.6 E0613 AC 1
A079 AC ¾ 212 125 100 35 396 80 2.0 E0620 AC 1
A108 AC 1 229 135 100 35 396 80 2.0 E0620 AC 1
A109 AC 1 297 175 100 35 396 80 2.0 E0625 AC 1
A128 AC 1¼ 476 280 122 42 460 80 2.8 E0730 AC 1
A158 AC 1½ 545 320 122 42 460 80 2.8 E0730 AC 1
A159 AC 1½ 680 400 146 52 482 100 4.2 E0830 AC 1
A208 AC 2 765 450 146 52 482 100 4.2 E0830 AC 1
A209 AC 2 1190 700 146 52 785 100 6.3 E0860 AC 1
A254 AC 2½ 1445 850 210 67 595 100 8.5 E1140 AC 1
A340 AC 3 1530 900 210 67 595 100 8.5 E1140 AC 1
A360 AC 3 2125 1250 210 67 815 100 10.5 E1160 AC 1
A390 AC 3 2550 1500 210 67 975 100 12.0 E1175 AC 1
A391 AC DN80 2160 1270 450 265 1205 700 58 E139 AC 1

A483 AC DN100 3100 1824 520 285 1245 700 74 E88 AC 3
A484 AC DN100 4250 2500 520 285 1245 700 74 E88 AC 4
A686 AC DN150 6500 3824 680 400 1400 700 165 E88 AC 6
A688 AC DN150 8720 5130 780 400 1430 700 208 E88 AC 8
A8810 AC DN200 11000 6470 780 400 1460 700 260 E88 AC 10
A10816 AC DN250 17000 10000 900 550 1570 700 450 E88 AC 16
A12824 AC DN300 25500 15000 900 600 1620 700 740 E88 AC 24

A A
B
B
C C
AC element Semi-automatic drain valve

SDV 25 30mm
approx.
D
D
A018 AC to A391 AC to
specification
A390 AC A12824 AC
technical notes
Direction of air flow is inside to out through the 1 Grade AC
filter element.
Activated carbon filters do not include differential 2
pressure equipment. Maximum oil content class to ISO 8573-1:2010 1
Semi automatic drain valves SDV25 are fitted to models 3 Particle removal 0.01 micron
A018 AC to A390 AC. On models A391 AC to A8810 AC, Maximum oil carryover at 20°C (68°F) 0.003 mg/m³ 0.003 ppm
½" manual drain valves are fitted; ¾" on models
Maximum temperature * 50°C 122°F
A10816 AC and A12824 AC.
Models A059 AC to A390 AC can be adapted to use ¼" 4 Maximum working pressure 16 barg 232 psig
drains with a reducer. Element end cap colour black
Activated carbon filters must not operate in oil saturated 5
conditions and will not remove certain types of gases
including carbon monoxide (CO) and carbon dioxide (CO2).
* Recommended operating temperature 25°C, 77°F. 6
17
The alpha series XAC duplex range of filters offers a space saving, economical
filtration solution. Duplex filters combine an XA 0.01 micron coalescing filter element
which reduces oil concentrations and an AC, secondary activated carbon filter
element which removes vapours, odours and tastes.
XAC 2 stage duplex filtration

filter pipe flow rate dimensions (mm) weight complete element element price no. of
JANUARY 2012
model size Kg price model elements

Nm3/h SCFM A B C D XA DAC
D028 XAC ¼ 42.5 25 70 163 159 70 0.9 E0406 XA / E0407 DAC 1/1
D038 XAC 59.5 35 70 163 159 70 0.9 E0407 XA / E0407 DAC 1/1
D058 XAC ½ 85.0 50 70 204 200 70 1.0 E0413 XA / E0413 DAC 1/1
D059 XAC ½ 119 70 100 240 236 80 2.3 E0613 XA / E0613 DAC 1/1
D078 XAC ¾ 144 85 100 240 236 80 2.3 E0613 XA / E0613 DAC 1/1
D079 XAC ¾ 212 125 100 360 356 80 3.1 E0620 XA / E0625 DAC 1/1
D108 XAC 1 229 135 100 360 356 80 3.1 E0620 XA / E0625 DAC 1/1
D109 XAC 1 297 175 100 360 356 80 3.2 E0625 XA / E0625 DAC 1/1

A
C
XA element DAC element Float operated drain valve
D028 to D058 order DVAS16C
D059 to D109 order DVAS16
30mm
D approx.
D028 XAC to D109 XAC
specification
Grade XA AC
Maximum particle size class to ISO 8573-1:2010 1 1
Maximum oil content class to ISO 8573-1:2010 1 1
Maximum temperature * 50°C 122°F 50°C 122°F
Maximum working pressure 16 barg 232 psig 16 barg 232 psig
Element end cap colour blue XA (bottom element) black activated carbon (top element)
technical notes
1 Duplex filters offer 2 stage filtration within one filter unit. Each filtration package provides an XA grade element
in the lower section for oil removal, while the AC grade element in the upper section is for odour removal.
2 Direction of air flow is inside to out through XA grade and outside to in through AC grade filter element.
3 DVAS16C drains are fitted to models D028 XAC to D058 XAC; DVAS16 drains are fitted to D059 XAC to D109
XAC.
4 Models D059 XAC to D109 XAC can be adapted to use ¼" drains with a reducer.
5 Activated carbon filters must not operate in oil saturated conditions and will not remove certain types of gases
6 * Recommended operating temperature 25°C, 77°F.
18 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Walker Filtration offer alpha series dust removal filters for installation downstream
of regenerative compressed air and gas dryers. These filters ensure protection of the
equipment from dust carryover. Grade RAC will also remove odours.
dust filtration RX
JANUARY 2012
A018 (grade) ¼ 13.6 8 50 18 152 60 0.3 E0304 (grade) 1
A019 (grade) ¼ 25.5 15 50 18 152 60 0.3 E0305 (grade) 1
A028 (grade) ¼ 42.5 25 70 65 231 70 0.6 E0406 (grade) 1
A038 (grade) 59.5 35 70 65 231 70 0.6 E0407 (grade) 1
A058 (grade) ½ 85.0 50 70 65 272 70 0.7 E0413 (grade) 1
A059 (grade) ½ 119 70 100 105 346 80 1.6 E0613 (grade) 1
A078 (grade) ¾ 144 85 100 105 346 80 1.6 E0613 (grade) 1
A079 (grade) ¾ 212 125 100 105 466 80 2.0 E0620 (grade) 1
A108 (grade) 1 229 135 100 105 466 80 2.0 E0620 (grade) 1
A109 (grade) 1 297 175 100 105 466 80 2.0 E0625 (grade) 1
A128 (grade) 1¼ 476 280 122 112 530 80 2.8 E0730 (grade) 1
A158 (grade) 1½ 545 320 122 112 530 80 2.8 E0730 (grade) 1
A159 (grade) 1½ 680 400 146 122 552 100 4.2 E0830 (grade) 1
A208 (grade) 2 765 450 146 122 552 100 4.2 E0830 (grade) 1
A209 (grade) 2 1190 700 146 122 855 100 6.3 E0860 (grade) 1
A254 (grade) 2½ 1445 850 210 137 665 100 8.5 E1140 (grade) 1
A340 (grade) 3 1530 900 210 137 665 100 8.5 E1140 (grade) 1
A360 (grade) 3 2125 1250 210 137 885 100 10.5 E1160 (grade) 1
A390 (grade) 3 2550 1500 210 137 1045 100 12.0 E1175 (grade) 1
A391 (grade) DN80 2160 1270 450 265 1205 700 58 E139 (grade) 1
A483 (grade) DN100 3100 1824 520 285 1245 700 74 E88 (grade) 3
A484 (grade) DN100 4250 2500 520 285 1245 700 74 E88 (grade) 4
A686 (grade) DN150 6500 3824 680 400 1400 700 165 E88 (grade) 6
A688 (grade) DN150 8720 5130 780 400 1430 700 208 E88 (grade) 8
A8810 (grade) DN200 11000 6470 780 400 1460 700 260 E88 (grade) 10
A10816 (grade) DN250 17000 10000 900 550 1570 700 450 E88 (grade) 16
A12824 (grade) DN300 25500 15000 900 600 1620 700 740 E88 (grade) 24
specification
Grade RX25 RX5 RX1 RXA RAC
Particle removal 25 micron 5 micron 1 micron 0.1 micron 0.01 micron
Maximum oil carryover at 20°C (68°F) - - - - 0.003 mg/m³ 0.003 ppm
Maximum temperature 120°C 248°F 120°C 248°F 120°C 248°F 120°C 248°F 50°C * 122°F *
Maximum working pressure 16 barg 232 psig 16 barg 232 psig 16 barg 232 psig 16 barg 232 psig 16 barg 232 psig
Element end cap colour black green red blue black

A A
technical notes
B
1 Direction of air flow is outside to in through the filter B
element.
2 Pop up indicators (65DPUG) are fitted to models A028 to
A058 as standard. Differential pressure indicators (65DPIG)
C C
are fitted to models A059 to A12824. RAC grade filters do
not include DP equipment.
Manual drain valve Differential pressure gauge 3 Manual drain valves (MDV25) are fitted to A018 to A390.
MDV 25 65DPIG Flanged filters are fitted with manual drain valves, on 50mm
approx.
models A391 to A8810, ½" are fitted; ¾" on models D
A10816 to A12824. D
4 Models A059 to A390 can be adapted to use ¼" drains
with a reducer.
5 An additional ½" side entry port is included on models
A391 to A8810, ¾" for A10816 and A12824.
6 Activated carbon filters must not operate in oil saturated A018 (grade) to A391 (grade) to
conditions and will not remove certain types of gases A390 (grade) A12824 (grade)
RX1 element shown
19
High temperature dust filters are essential for use in specialist high temperature
applications. These products are used downstream of heat regenerative dryers,
where for short periods of time, the temperature of the air may reach a maximum
of 250°C / 482°F.
HT high temperature dust filtration

filter pipe flow rate dimensions (mm) weight complete element element
model size Nm3/h SCFM A B C D Kg price model price
JANUARY 2012
HT25 (grade) ¼ 35 20 85 18 170 75 1.7 E50 (grade)

HT31 (grade) 52 30 85 18 205 100 2.0 E51 (grade)
HT50 (grade) ½ 108 63 85 18 225 100 2.2 E52 (grade)
HT75 (grade) ¾ 216 127 110 27 270 150 4.0 E715 (grade)
HT101 (grade) 1 300 176 110 27 420 300 5.0 E730 (grade)
HT150 (grade) 1½ 725 427 150 45 525 300 15.0 E830 (grade)
HT200 (grade) 2 800 470 150 45 525 300 15.0 E830 (grade)
HT201 (grade) 2 1150 675 150 45 825 500 21.0 E86 (grade)

A
HT25 to HT201
specification
Grade HRX5 HRX1 HRXA
Particle removal 5 micron 1 micron 0.01 micron
Maximum temperature 250°C 482°F 250°C 482°F 250°C 482°F
Maximum working pressure 16 barg 232 psig 16 barg 232 psig 16 barg 232 psig
Element end cap material stainless steel
technical notes
1 High temperature filters are manufactured from 316 grade stainless steel and are uncoated.
2 Direction of air flow is outside to in through the filter element.
3 High temperature threaded filters are supplied without a drain valve.
4 Drain ports are 1/8" on models HT25 to HT50 and ¼" on models HT75 to HT201.
20 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Manufactured from aluminium, the 20 barg (300 psig) range of filters offer flows
up to 2580 SCFM (4383 Nm³/hr). These products are ideally suited for high pressure
industrial use, such as high pressure testing.
alloy high pressure filters 20 barg

JANUARY 2012
20HP25 (grade) ¼ 59 35 72 35 184 75 0.65 E1003 (grade)
20HP37 (grade) 85 50 72 35 184 75 0.65 E1503 (grade)
20HP50 (grade) ½ 110 65 114 38 270 152 2.0 E2005 (grade)
20HP75 (grade) ¾ 219 129 114 38 270 152 2.0 E2505 (grade)
20HP100 (grade) 1 292 172 114 38 352 152 2.5 E2008 (grade)
20HP101 (grade) 1 438 258 114 38 352 152 2.5 E2508 (grade)
20HP150 (grade) 1½ 658 387 146 51 490 165 5.0 E2512 (grade)
20HP151 (grade) 1½ 877 516 146 51 490 165 5.0 E2712 (grade)
20HP200 (grade) 2 1315 774 146 51 490 165 5.0 E3012 (grade)
20HP201 (grade) 2 1899 1118 146 51 685 165 6.0 E3020 (grade)
20HP300 (grade) 3 2922 1720 229 64 681 178 15.0 E5020 (grade)
20HP301 (grade) 3 3653 2150 229 64 810 178 15.0 E5024 (grade)
20HP302 (grade) 3 4383 2580 229 64 962 178 16.0 E5030 (grade)

B A A B
C
C
D
D
specification
20HP25 (grade) to 20HP50 (grade) to
20HP37 (grade) 20HP302 (grade)
Coalescing filter element grades

Grade X25 X5 X1 XA AC
Maximum oil carryover at 20°C (68°F) 10 mg/m³ 8.2 ppm 5 mg/m³ 4.1 ppm 0.1 mg/m³ 0.1 ppm 0.01 mg/m³ 0.01 ppm 0.003 mg/m³ 0.003 ppm
Maximum working pressure 20 barg (300 psig)
Dust filter element grades

Maximum oil carryover at 20°C (68°F) - - - - - - - 0.003 mg/m³ 0.003 ppm
technical notes
1 Direction of air flow is inside to out through the filter element for coalescing grades and outside to in through
the filter element for dust grades.
2 All alloy high pressure filters are supplied with a drain plug. High pressure drains are available, see page 39.
3 Differential pressure indicators are available for 20 barg applications.
21
Walker Filtration manufacture a range of 50 barg (725 psig) high pressure filters
using machined or die cast aluminium components. Ideally suited to a wide range
of industrial applications such as pharmaceutical testing, packaging and PET bottle
manufacturing.
50 barg alloy high pressure filters

JANUARY 2012
50HP25 (grade) ¼ 160 94 63 15 150 50 0.3 HP1535 (grade)

50HP37 (grade) 250 147 63 15 190 50 0.3 HP1550 (grade)
50HP50 (grade) ½ 450 265 114 38 305 150 2.6 HP2040 (grade)
50HP75 (grade) ¾ 550 324 114 38 305 150 2.6 HP2540 (grade)
50HP101 (grade) 1 835 492 114 38 395 150 3.3 HP2080 (grade)
50HP150 (grade) 1½ 1250 736 146 50 435 170 7.5 HP2580 (grade)
50HP151 (grade) 1½ 1725 1015 146 50 435 170 7.5 HP2512 (grade)
50HP200 (grade) 2 1925 1132 146 50 435 170 7.5 HP2512 (grade)
50HP201 (grade) 2 3200 1882 146 50 635 170 10.0 HP2520 (grade)

B A A B
C C
D D
50HP25 (grade) to 50HP50 (grade) to

50HP37 (grade) 50HP201 (grade)
specification
Grade WS X25 X5 X1 XA AC
Particle removal - 25 micron 5 micron 1 micron 0.01 micron 0.01 micron
Maximum oil carryover at 20°C (68°F) - 10 mg/m³ 8.2 ppm 5 mg/m³ 4.1ppm 0.1 mg/m³ 0.1 ppm 0.01 mg/m³ 0.01 ppm 0.003 mg/m³ 0.003 ppm
Maximum temperature 120°C 248°F 120°C 248°F 120°C 248°F 120°C 248°F 120°C 248°F 50°C * 122°F *
Element end cap colour - black

technical notes
1 Direction of air flow is inside to out through the filter element for coalescing grades and outside to in through
2 All alloy high pressure filters are supplied with a drain plug. High pressure drains are available, see page 39.
22 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Manufactured from high grade stainless steel, these filters operate at pressures
up to 350 barg (5000 psig). Ideally suited to industries such as PET bottle blowing,
offshore, instrumentation, medical, as well as heavy industrial environments.
stainless steel
high pressure filters HP
JANUARY 2012
50 barg (725 psig) maximum working pressure
C25 (grade) ¼ 100 60 85 18 170 75 1.7 E50 (grade)
C37 (grade) 200 120 85 18 205 100 2.0 E51 (grade)
C50 (grade) ½ 340 200 85 18 255 100 2.2 E52 (grade)
C75 (grade) ¾ 500 300 110 27 270 150 4.0 E715 (grade)
C101 (grade) 1 1000 600 110 27 420 300 5.0 E730 (grade)
C150 (grade) 1½ 1700 1000 150 45 525 300 15.0 E830 (grade)
C200 (grade) 2 2040 1200 150 45 525 300 15.0 E830 (grade)
C201 (grade) 2 3400 2000 150 45 825 500 21.0 E86 (grade)
100HP24 (grade) ¼ 100 60 65 20 135 70 3.2 HP371 (grade)
100HP49 (grade) ½ 315 185 65 20 250 180 5.6 HP381 (grade)
100HP75 (grade) ¾ 460 270 88 20 275 250 6.1 HP420 (grade)
100HP100 (grade) 1 680 400 132 26 265 150 10.5 HP710 (grade)
100HP101 (grade) 1 1200 700 132 26 480 300 14.7 HP730 (grade)
100HP150 (grade) 1½ 1700 1000 150 45 525 300 22.0 HP830 (grade)
100HP200 (grade) 2 3400 2000 150 45 825 500 28.0 HP860 (grade)
350HP24 (grade) ¼ 48 28 41 10 103 60 1.6 HP261 (grade)
350HP26 (grade) ¼ 111 67 65 20 135 70 3.2 HP371 (grade)
350HP50 (grade) ½ 255 150 88 20 210 150 5.6 HP410 (grade)
350HP75 (grade) ¾ 510 300 88 25 280 250 6.1 HP420 (grade)
350HP100 (grade) 1 750 445 150 35 330 200 14.5 HP710 (grade)
350HP101 (grade) 1 1330 775 150 35 480 300 17.4 HP730 (grade)

specification
Grade WS X25 X5 X1 XA AC
Particle removal - 25 micron 5 micron 1 micron 0.01 micron 0.01 micron
Maximum oil carryover at 20°C (68°F) - 10 mg/m³ 8.2 ppm 5 mg/m³ 4.1ppm 0.1 mg/m³ 0.1 ppm 0.01 mg/m³ 0.01 ppm 0.003 mg/m³ 0.003 ppm
Maximum temperature 120°C 248°F 120°C 248°F 120°C 248°F 120°C 248°F 120°C 248°F 50°C * 122°F *
Element end cap colour 50barg - black green red blue black
Element end cap colour 100 & 350barg - stainless steel
Element end cap colour 50barg black green red blue black
Element end cap colour 100 & 350barg stainless steel
B A A B
technical notes
1 Direction of air flow is inside to out through filter elements for coalescing grades and outside to in through
2 All high pressure filters are supplied with a drain plug. High pressure drains are available, see page 39.
C C
4 Filter element end caps are colour coded on ‘C’ range and stainless steel on 100HP and 350HP range.
D D
C25 (grade) to 100HP24 (grade) to

C201 (grade) 350HP101 (grade)
23
Our range of alpha series medical sterile filters has been specifically designed for
medical compressed air plants, as used in hospitals throughout the world. This range
meets all requirements of the UK Health Technical Memorandum 02-01 guidance on
medical gas pipeline systems.
MS medical sterile filters

filter pipe flow rate dimensions (mm) weight complete element
element price
model size Nm3/h SCFM A B C D Kg price model
JANUARY 2012
A019 MS ¼ 25.5 15 50 18 152 60 0.5 E0305 SR

A028 MS ¼ 42.5 25 70 65 231 70 0.8 E0407 SR
A038 MS 59.5 35 70 65 231 70 0.8 E0407 SR
A058 MS ½ 85.0 50 70 65 272 70 0.9 E0413 SR
A059 MS ½ 119 70 100 105 346 80 2.0 E0613 SR
A078 MS ¾ 144 85 100 105 346 80 2.0 E0613 SR
A109 MS 1 297 175 100 105 466 80 2.4 E0625 SR
A128 MS 1¼ 476 280 122 112 530 80 3.3 E0730 SR
A158 MS 1½ 545 320 122 112 530 80 3.3 E0730 SR
A159 MS 1½ 680 400 146 122 552 100 4.9 E0830 SR
A208 MS 2 765 450 146 122 552 100 4.9 E0830 SR
A209 MS 2 1190 700 146 122 855 100 7.0 E0860 SR
A254 MS 2½ 1445 850 210 137 665 100 9.6 E1140 SR
A340 MS 3 1530 900 210 137 665 100 9.6 E1140 SR
A360 MS 3 2125 1250 210 137 885 100 11.6 E1160 SR
A390 MS 3 2550 1500 210 137 1045 100 13.1 E1175 SR

A
MS element Differential pressure gauge Manual drain valve

65DPIG MDV 25
50mm
D approx.
A019 MS to A390 MS
specification
Grade SR
Particle removal 0.01 micron
Maximum autoclave temperature 134°C 273°F
Maximum working pressure 16 barg 232 psig
technical notes
1 Filter element endcaps are stainless steel.
3 Pop up indicators (65DPUG) are fitted to models A028 MS to A058 MS as standard.
Differential pressure indicators (65DPIG) are fitted to models A059 MS to A390 MS.
4 Manual drain valves are fitted to all models. Models A059 MS to A390 MS can be adapted to use ¼" drains
with a reducer.
5 Medical sterile filter elements must not operate in water or oil saturated conditions.
6 Maximum steam sterilising temperature refers to the filter element ONLY. Grade SR filter elements can be
steam sterilised 100 times. Each element must be autoclaved before commencement of duty.
7 Pre-filtration should be used in conjuction with 0.01 micron sterile filters.
24 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Autoclave filters are recommended for use in sterilising atmospheric air entering
hospital and laboratory sterilisers during the vacuum break cycle.
autoclave filter elements AF

filter connection flow rate dimensions (mm) weight complete
model size Nm3/h SCFM A B C (Kg) price
JANUARY 2012
AF1 Rp ½ 20 12 83 23 103 0.29
AF2 Rp ½ 40 24 83 23 183 0.35
AF1 socks foam prefilter socks to fit AF1 (pack of ten)
AF2 socks foam prefilter socks to fit AF2 (pack of ten)
specification
Grade AF
Particle removal 0.01 micron AF1 & AF2
Penetration at 0.3 micron <0.001%
Maximum steam sterilisation temperature 134°C 273°F
Element end cap material acetal
technical notes
1 Autoclave filter elements are manufactured from corrosion resistant materials and are designed specifically to
operate in arduous environments.
2 The elements can be steam sterilised at 134°C (273°F) and are guaranteed for up to 50 sterilisation cycles.
3 High efficiency borosilicate glass microfibre filter media offers over 95% voids volume providing exceptionally high
dirt holding capacity for long service life.
4 Borosilicate glass microfibre media will not allow 'grow through' of bacteria and assures complete protection
against the ingress of contamination.
5 Each autoclave filter is supplied with a replaceable outer foam pre-filtration sock. This provides protection to the
high efficiency microfibre media against large atmospheric dirt particles.
25
Our range of alpha series vacuum pump protection filters has a rating of 0.1 Torr and
are suitable for both rough and high vacuum applications.
VLR vacuum pump

VX1 protection filters
exhaust flow rate
filter pipe dimensions (mm) weight complete element element
(vacuum displacement)
JANUARY 2012
model size Kg price model price

Nm3/h SCFM A B C D
A038 (grade) 7 4.1 70 65 231 70 0.6 E0407 (grade)
A058 (grade) ½ 11 6.5 70 65 272 70 0.7 E0413 (grade)
A059 (grade) ½ 20 11.8 100 105 346 80 1.6 E0613 (grade)
A078 (grade) ¾ 25 14.7 100 105 346 80 1.6 E0613 (grade)
A079 (grade) ¾ 35 20.6 100 105 466 80 2.0 E0620 (grade)
A108 (grade) 1 40 23.5 100 105 466 80 2.0 E0620 (grade)
A109 (grade) 1 50 29.4 100 105 466 80 2.0 E0625 (grade)
A128 (grade) 1¼ 75 44.1 122 112 530 80 2.8 E0730 (grade)
A158 (grade) 1½ 85 50.0 122 112 530 80 2.8 E0730 (grade)
A159 (grade) 1½ 100 59.0 146 122 552 100 4.2 E0830 (grade)
A208 (grade) 2 115 67.5 146 122 552 100 4.2 E0830 (grade)
A209 (grade) 2 180 106 146 122 855 100 6.3 E0860 (grade)
A254 (grade) 2½ 200 118 210 137 665 100 8.5 E1140 (grade)
A340 (grade) 3 235 138 210 137 665 100 8.5 E1140 (grade)
A360 (grade) 3 360 212 210 137 885 100 10.5 E1160 (grade)
A390 (grade) 3 490 288 210 137 1045 100 12.0 E1175 (grade)

A
VX1 element shown Manual drain valve

MDV 25
50mm
D approx.
A038 (grade) to A390 (grade)
specification
Grade VLR VX1
Particle removal 5 micron 1 micron
Maximum temperature 120°C 248°F 120°C 248°F
Maximum working vacuum full vacuum full vacuum
Element end cap colour code green red
technical notes
1 Direction of air flow is inside to out through the filter element.
2 Pop up indicators (65DPUGA-100) are fitted to models A038 to A058. Differential pressure gauges
(65DPG250G) are fitted to models A059 to A390 as standard.
3 Manual drain valves are fitted to all models. Models A059 to A390 can be adapted to use ¼" drains with a reducer.
4 Drain flasks are available for liquid collection for use at atmospheric pressure or vacuum only (refer to page 41).
26 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Walker Filtration offers three types of alpha series vacuum pump exhaust filters, all of
which are designed for oil mist removal from oil injected vacuum pumps.
vacuum pump
exhaust filters EF
exhaust flow rate
filter pipe dimensions (mm) weight complete element element
(vacuum displacement)
JANUARY 2012
model size Kg price model price
Nm3/h SCFM A B C D
A038 EF 7 4.1 70 65 231 70 0.6 E0407 EF
A058 EF ½ 11 6.5 70 65 272 70 0.7 E0413 EF
A059 EF ½ 20 11.8 100 105 346 80 1.6 E0613 EF
A078 EF ¾ 25 14.7 100 105 346 80 1.6 E0613 EF
A079 EF ¾ 35 20.6 100 105 466 80 2.0 E0620 EF
A108 EF 1 40 23.5 100 105 466 80 2.0 E0620 EF
A109 EF 1 50 29.4 100 105 466 80 2.0 E0625 EF
A128 EF 1¼ 75 44.1 122 112 530 80 2.8 E0730 EF
A158 EF 1½ 85 50.0 122 112 530 80 2.8 E0730 EF
A159 EF 1½ 100 59.0 146 122 552 100 4.2 E0830 EF
A208 EF 2 115 67.5 146 122 552 100 4.2 E0830 EF
A209 EF 2 180 106 146 122 855 100 6.3 E0860 EF
A254 EF 2½ 200 118 210 137 665 100 8.5 E1140 EF
A340 EF 3 235 138 210 137 665 100 8.5 E1140 EF
A360 EF 3 360 212 210 137 885 100 10.5 E1160 EF
A390 EF 3 490 288 210 137 1045 100 12.0 E1175 EF
D038 EFC 7 4.1 70 163 159 70 0.9 E0407 EF / E0407 DAC
D058 EFC ½ 11 6.5 70 204 200 70 1.0 E0413 EF / E0413 DAC
D059 EFC ½ 20 11.8 100 240 236 80 2.3 E0613 EF / E0613 DAC
D078 EFC ¾ 25 14.7 100 240 236 80 2.3 E0613 EF / E0613 DAC
D079 EFC ¾ 35 20.6 100 360 356 80 3.1 E0620 EF / E0625 DAC
D108 EFC 1 40 23.5 100 360 356 80 3.1 E0620 EF / E0625 DAC
D109 EFC 1 50 29.4 100 360 356 80 3.2 E0625 EF / E0625 DAC

A
A B
B
C C
EF element Manual drain valve
MDV 25
specification 50mm
50mm approx.
D approx. D
Grade EF DAC
Particle removal 0.1 micron 0.1 micron
Maximum oil carryover at 20°C (68°F) 1 mg/m3 0.82 ppm 1 mg/m3 0.82 ppm
Maximum temperature 120°C 248°F 50°C * 122°F * A038 EF to D038 EFC to
Element end cap colour code black black A390 EF D109 EFC
technical notes
1 Duplex filters offer 2 stage filtration within one filter unit. Each filtration package provides an EF grade element
2 Direction of air flow is inside to out through EF grade and outside to in through AC grade filter element.
3 Differential pressure (DP) equipment fitted as standard (excluding AC grade filters): 65DPUGA-100 pop-up
indicators to models A038 to A058, 65DPG250G gauges to models A059 to A390.
4 Manual drain valves are fitted to all models. Models A059/D059 to A109/D109 can be adapted to use ¼"
drains with a reducer.
5 Drain flasks are available for liquid collection, for use at atmospheric pressure or vacuum only (refer to page 41).
27
For rotary vane type pumps with internal oil separation, Odasorb exhaust filters are
fitted directly to the pump outlet to provide a safe working environment.
OS odasorb exhaust filters

filter pipe flow rate dimensions weight complete
model size Nm3/h SCFM A B Kg price
JANUARY 2012
OS50 ¾ 50 30 80 150 0.8

OS75 1 75 45 100 150 0.9
OS100 1¼ 100 60 130 150 1.0
OS150 1½ 150 90 130 250 1.1
OS200 2 250 150 130 300 1.2
see
pipe size
specification
A
OS50 to OS200
Specification OS
Maximum temperature 120°C 248°F
Element end cap material zinc plated steel
technical notes
2 Odasorb products must be changed at least every six months.
28 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
The Walker Filtration range of alpha series medical vacuum filters is designed to
protect centralised hospital vacuum plant installations from liquid, solid and bacterial
contamination, as specified in the UK Health Technical Memorandum 02-01 guidance.
medical vacuum filters MV

free air capacity at
filter pipe dimensions (mm) weight complete element element No. of
atmospheric pressure
JANUARY 2012
model size Kg price model price elements
Nm³/h SCFM A B C D
A028 MV ¼ 3.5 2.1 70 65 390 70 0.6 E0406 MV 1
A038 MV 5 2.9 70 65 390 70 0.6 E0407 MV 1
A058 MV ½ 7 4.1 70 65 445 70 0.7 E0413 MV 1
A059 MV ½ 12 7.1 100 105 505 80 1.6 E0613 MV 1
A078 MV ¾ 15 8.8 100 105 505 80 1.6 E0613 MV 1
A079 MV ¾ 25 14.7 100 105 665 80 2.0 E0620 MV 1
A108 MV 1 33 19.4 100 105 665 80 2.0 E0620 MV 1
A109 MV 1 45 26.5 100 105 665 80 2.0 E0625 MV 1
A128 MV 1¼ 60 35.3 122 112 730 80 2.8 E0730 MV 1
A158 MV 1½ 70 41.2 122 112 730 80 2.8 E0730 MV 1
A159 MV 1½ 95 55.9 146 122 752 100 4.2 E0830 MV 1
A208 MV 2 120 70.6 146 122 752 100 4.2 E0830 MV 1
A209 MV 2 175 103 146 122 1055 100 6.3 E0860 MV 1
A254 MV 2½ 190 112 210 137 865 100 8.5 E1140 MV 1
A340 MV 3 200 118 210 137 865 100 8.5 E1140 MV 1
A360 MV 3 225 132 210 137 1085 100 10.5 E1160 MV 1
A390 MV 3 265 156 210 137 1205 100 12.0 E1175 MV 1
See page 12 for flanged
A391 MV DN80 330 194 450 265 1475 700 58 E139 MV 1

filter packaging
A483 MV DN100 406 238 520 285 1515 700 74 E88 MV 3

A484 MV DN100 492 289 520 285 1515 700 74 E88 MV 4
A686 MV DN150 660 388 680 400 1670 700 165 E88 MV 6

A A
B
B
C C
MV element Drain flask Manual drain valve

MDV 25
D D
specification
Grade MV A028 MV to A391 MV to
Particle removal efficiency* >99.995% A390 MV A686 MV
Maximum temperature 60°C 140°F
Maximum working pressure 0.5 barg 7 psig (see note 5)
Maximum working vacuum full vacuum
Element end cap colour code black
* in accordance with BS 3928-1969
technical notes
2 Pop up indicators (65DPUBA-100) are fitted to models A028 MV to A058 MV as standard. Differential pressure
gauges (65DPG250B) are fitted to models A059 MV to A390 MV as standard. Differential pressure gauges are
fitted to all flanged models.
3 Manual drain valves (MDV25) are fitted to all models. Sterilisable glass drain flasks are supplied as standard,
100ml for models A028 MV to A078 MV and 250ml for A079 MV to A390 MV. An additional ½" side entry
drain port is included on models A391 MV to A686 MV.
4 Flow rates shown above are free air conditions when operating at atmospheric pressure.
5 Pressure for leak testing purposes MUST be limited to 7 barg and only applied with the drain valve and drain
flask REMOVED.
29
Ammonia and refrigerant filters have been designed for use in specialist applications
where the quality and cleanliness of the gas needs to be maintained to the highest
level.
NH3 ammonia & refrigerant filters

filter pipe flow rate dimensions (mm) weight complete element element No. of
JANUARY 2012
C25 (grade) ¼ 35 20 85 18 170 75 1.7 E50 (grade) NH3 1

C37 (grade) 52 30 85 18 205 100 2.0 E51 (grade) NH3 1
C50 (grade) ½ 108 63 85 18 255 100 2.2 E52 (grade) NH3 1
C75 (grade) ¾ 216 127 110 27 270 150 4.0 E715 (grade) NH3 1
C101 (grade) 1 300 176 110 27 420 300 5.0 E730 (grade) NH3 1
C150 (grade) 1½ 725 427 150 45 525 300 15.0 E830 (grade) NH3 1
C200 (grade) 2 800 470 150 45 525 300 15.0 E830 (grade) NH3 1
C201 (grade) 2 1150 675 150 45 825 500 21.0 E86 (grade) NH3 1

A
NH3 filter element
C25 (grade) to C201 (grade)
specification
Grade X1 NH3 XA NH3
Particle removal 1 micron 0.01 micron
Max. oil carryover at 20°C (68°F) 0.1 mg/m³ 0.1 ppm 0.01 mg/m³ 0.01 ppm
Maximum temperature 120°C 248°F 120°C 248°F
technical notes
1 Ammonia and refrigerant filters are manufactured from stainless steel.
2 Direction of air flow is inside to out through the filter element.
3 Models C25 to C201 are supplied with a drain plug.
4 All ammonia and refrigerant filters are PED compliant for Group 1 Gases.
30 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Compressed air in-line heater packages ensure variable compressed air temperature
control from 20°C (68°F) to 120°C (248°F), ideally suitable for industrial or breathing
air applications.
heater & filter heater FH

model size Nm³/h SCFM A B C Kg price model price
JANUARY 2012
A39BH 47 27 88 130 337 1.0 - -
A39TH 47 27 138 130 337 1.3 - -
A39FH 47 27 176 130 337 2.3 E511 XA
A39FTH 47 27 226 130 337 2.6 E511 XA
A55BH ½ 92 54 88 130 337 1.0 - -
A55TH ½ 92 54 138 130 337 1.3 - -
A55FH ½ 92 54 176 130 337 2.3 E511 XA
A55FTH ½ 92 54 226 130 337 2.6 E511 XA
A A
100
(212)
B B
80
(175)
C C
60
(140)
40
(104) A39BH & A39TH &
A55BH A55TH
20
(68)
A A
0
47 (27) 92 (54) B B
FLOW Nm3/h (SCFM)

C C
A39FH & A39FTH &

A55FH A55FTH
specification
Heater specification 230 volt AC 115 volt AC
Supply voltage 230 volt AC-50/60Hz 115 volt AC-50/60Hz
Power rating 1.5Kw 1.5Kw
Controlled output range 20°C to 120°C 68°F to 248°F 20°C to 120°C 68°F to 248°F
Minimum inlet temperature -20°C -4°F -20°C -4°F
replacement parts for heater models

model description complete price
WKN40037 replacement heating element P.O.A.
WKN40170 replacement printed circuit board P.O.A.
WKN40171 replacement sensor P.O.A.
WKN40173 replacement thermometer P.O.A.
technical notes
1 Semi-automatic drain valve (SDV25) are fitted to all heaters. Float operated automatic drain valves (ADV16) are
fitted to all filters.
2 When liquid, oil and water are present, FH or FTH models should be specified.
3 Electrical connections to the unit are via an industry standard DIN connector.
4 When placing an order, please specify voltage required. Example A39FTH-115.
5 If used in a breathing air installation, please note adequate breathing air filtration is required prior to the heater
assembly. Heater and filter heater packages will not remove certain types of gases including carbon monoxide
(CO) and carbon dioxide (CO2).
6 Minimum flow rate of 3Nm3/h (1.7CFM) is recommended.
31
This product range has been designed to provide the user with a clean supply
of compressed air, to ensure the safety of personnel operating in hazardous or
contaminated conditions.
BA breathing & medical air

inlet flow rate outlet flow rate dimensions (mm) element element
pipe weight complete element element
model model price
JANUARY 2012
size Nm³/h SCFM Nm³/h SCFM A B C Kg price model (HC) price (HC)
(grade) (grade)
BA025 ½ 42 25 34 20 633 1130 92 30 E511 (grade) E521 HC
BA035 ½ 59 35 48 28 633 1525 92 37 E511 (grade) E521 HC
BA045 ¾ 76 45 61 36 520 765 664 64 E711 (grade) E811 HC
BA055 ¾ 93 55 75 44 520 865 664 70 E711 (grade) E811 HC
BA065 ¾ 110 65 88 52 520 965 664 75 E711 (grade) E811 HC
BA085 1 144 85 116 68 520 1165 664 86 E811 (grade) E731 HC
BA105 1 178 105 143 84 520 1475 664 102 E811 (grade) E731 HC
BA135 1 229 135 184 108 520 1675 664 116 E731 (grade) E731 HC
BA175 1 297 175 238 140 520 2075 664 137 E731 (grade) E731 HC
accessories
dryer
description kit number price
model
BA025 PDMC025-12000 12,000 hour service kit includes:
BA035 PDMC035-12000 desiccant cartridges, pack of sealing O-rings and
sealing washers,
BA045 PDMC045-12000 instruction manual, controller re-set disc.
service kit (2 cartridges)
BA055 PDMC055-12000
BA065 PDMC065-12000
BA085 PDMC085-12000
BA105 PDMC105-12000
BA135 service kit (4 cartridges) PDMC135-12000
BA175 PDMC175-12000
Packaging specifications
Breathing air purifiers are supplied in a timber framed 12mm plywood
All models
crate, suitable for international transportation. Each crate has a foam
lined interior to protect dryer from transit damage.
A C
X1 XA HC AC
specification
B
Maximum operating pressure 16 barg 232 psig
Minimum operating pressure 4 barg 58 psig
Maximum recommended inlet temperature 30ºC 86ºF
Minimum inlet temperature 1.5ºC 35ºF
BA025 to BA035 Power supply 12VDC to 24VDC 100VAC to 240VAC
A C
technical notes
1 Breathing and medical air must be installed and maintained in accordance with local regulations and standards.
X1 XA HC AC 2 Models are supplied together with an X1, XA, HC and AC filters.
B 3 Meets requirements specified in BS EN 12021 and European Pharmacopeia.
These filter packages typically exceed requirements of EN12021, but will not completely remove certain types of
4
gases including Carbon Monoxide (CO) and Carbon Dioxide (CO2).
5 Standard models operate at 7 barg; for other pressures, add suffix e.g. BA045R12 for 12 barg operation.
6 For NPT versions, replace R with N in model number e.g. BA045N.
7 Standard models supplied with pressure gauges, electronic fault alarm and diagnostic controller.
BA045 to BA175 8 Standard models supplied with 100-240 VAC at 50-60Hz or 12VDC to 24VDC.
32 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Walker Filtration offers a comprehensive range of wall or floor mounted breathable
compressed air products to suit 2 and 4 man breathing air installations. These purification
packages consist of a high dirt holding capacity 0.01 micron rated filter to remove
particles and oil aerosol and an activated carbon filter to remove odours and vapours.
breathable compressed air BA

inlet flow rate dimensions (mm)
filter weight no. of complete element element
pipe
model Kg outlets price model price
JANUARY 2012
size Nm³/h SCFM A B C D
BA20W ¼ 25 15 260 320 323 77 0.90 2 at " E361XA / E381AC
BA20WH ¼ 25 15 398 458 337 100 0.90 2 at " E361XA / E381AC
BA20F ¼ 25 15 500 n/a 450 500 0.90 2 at " E361XA / E381AC
BA20FH ¼ 25 15 500 n/a 450 500 0.90 2 at " E361XA / E381AC
BA30W 50 30 260 320 323 77 0.95 4 at " E371XA / E381AC
BA30WH 50 30 398 458 337 100 0.95 4 at " E371XA / E381AC
BA30F 50 30 500 n/a 450 500 0.95 4 at " E371XA / E381AC
BA30FH 50 30 500 n/a 450 500 0.95 4 at " E371XA / E381AC
D A
model description price B
BAF1 Stand alone frame assembly suitable for Rp ¼ to Rp filter assemblies

WKN40178 Air pressure regulator and pressure gauge
LPA1 Audible alarm for low inlet air pressure condition C
WKN40180 Manifold two port version
WKN40179 Manifold four port version
wall mountable option

BA20W / BA20WH (2 users)
ordering information BA30W / BA30WH (4 users)
BA20W or BA30W: wall mounting option with duplex filter.
BA20WH or BA30WH: wall mounting option with duplex filter and compressed air heater.
BA20F or BA30F: duplex filter mounted onto a portable frame.
BA20FH or BA30FH: duplex filter and compressed air heater mounted onto a portable frame.
D A
specification
Particle removal 0.01 micron
Maximum oil carryover at 20°C (68°F) 0.003 mg/m³ 0.003 ppm D A

Maximum working pressure 10 barg 145 psig C
floor standing option

BA20F / BA20FH (2 users)
technical notes
BA30F / BA30FH (4 users)
1 Duplex filters offer 2 stage filtration within one filter unit. Each filtration package provides an XA grade element
2 Direction of air flow is inside to out through XA grade and outside to in through AC grade filter element.
3 Breathable air filters include float operated drains as standard.
4 Self relieving air pressure regulators are used with 0 to 16 barg (0 to 232 psig) pressure gauges and can control
the outlet air pressure between 2 and 10 barg (29 and 145 psig).
5 Walker Filtration recommends that a water separator and a 1 micron particulate removal filter are installed prior
to breathable compressed air filter products.
33
compressed air dryers
JANUARY 2012
Any form of moisture in a The compact size of the Pro

compressed air line has the Dry ensures that installation
potential to cause costly is simple and versatile. The
downtime, machine damage units can be installed in small
and product spoilage. spaces in either a vertical or
horizontal position.
The highly efficient Pro Dry
range is recommended as an
integral part of a sophisticated
compressed air system,
which will provide significant
cost benefits if correctly
maintained.
This intelligent dryer has
additional energy saving
features, which link with a
compressor control system
and reduce air
consumption
during periods of
low demand.
34 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
COMPRESSED AIR DRYERS
The Pro Dry range of desiccant dryers is designed to eliminate moisture problems in
compressed air systems. When used in accordance with Walker Filtration coalescing
filters, the Pro Dry reduces moisture levels to -40°C (-40°F) and -70°C (-94°F) pressure
dewpoint.
pro dry desiccant dryers PD

pipe inlet flow rate dimensions (mm) weight filter complete
dryer model
size Nm³/h SCFM A B C Kg model price
JANUARY 2012
PD004 7 4 493 351 92 13 A038
PD006 10 6 552 351 92 14 A038
PD008 14 8 613 351 92 15 A038
PD010 17 10 682 351 92 17 A038
PD015 25 15 862 351 92 20 A038
PD025 42 25 1253 351 92 24 A038
PD035 59 35 1644 351 92 31 A038
PD045 ¾ 76 45 837 520 264 53 A078
PD055 ¾ 93 55 937 520 264 59 A078
PD065 ¾ 110 65 1037 520 264 64 A078
PD085 1 144 85 1237 520 264 75 A108
PD105 1 178 105 1547 520 264 91 A108
PD135 1¼ 229 135 1747 520 264 102 A128
PD175 1¼ 297 175 2147 520 264 123 A128
PD215 1½ 365 215 1555 520 448 172 A158
PD275 1½ 467 275 1755 520 448 192 A158
PD365 1½ 620 365 2165 520 474 232 A159
B C
specification
A
Standard pressure dewpoint -40°C -40°F
Optional pressure dewpoint -70°C -94°F
Minimum working pressure 4 barg 58 psig
Maximum working pressure 16 barg 232 psig
PD004 to PD035 Electronic control 100-240 VAC at 50-60Hz or 12VDC to 24VDC
Minimum inlet temperature 1.5°C 34°F
Maximum inlet temperature 50°C 122°F
B C
Minimum ambient temperature 5°C 41°F
technical notes
A 1 Pro Dry features easy removable desiccant cartridges with integral 1 micron dust filter.
2 For additional security, Walker Filtration recommends fitting an RX1 dust filter to the outlet.
3 All models are supplied together with an XA pre-filter.
4 Please see page 16 for replacement XA element to fit pre-filter.
5 Additional filtration, including a water separator, is recommended for high loaded inlet conditions.
6 Standard models operate at 7 barg; for other pressures, please specify at time of order.
PD045 to PD365 (see note 7) 7 PD215, PD275 and PD365 are duplex systems.
Complete system packaging price model packaging dimensions (mm) packaging price
PD045 915 x 680 x 460

Packaging specifications PD055 1015 x 680 x 460
PD065 1115 x 680 x 460
Pro Dry desiccant dryers are supplied in
a timber framed 12mm plywood crate, PD085 1315 x 680 x 460
suitable for international transportation. PD105 1625 x 680 x 460
Each crate has a foam lined interior to PD135 1825 x 680 x 460
protect dryer from transit damage. PD175 2225 x 680 x 460
Filtration is supplied in additional packaging PD215 1625 x 680 x 620
as a separate item. PD275 1825 x 680 x 620
PD365 2225 x 680 x 620
35
PD pro dry accessories

dryer
description service interval kit number price
model
JANUARY 2012
PD004 PDC004-12000
12,000 hour service kit includes:
PD006 PDC006-12000 desiccant cartridges,
PD008 PDC008-12000 pack of sealing O-rings and sealing washers,
instruction manual,
PD010 PDC010-12000 controller re-set disc.
PD015 required change: PDC015-12000
12,000 hours
PD025 service kit (2 cartridges) PDC025-12000
(2 years)
PD035 PDC035DF-12000
PD045 PDC045DF-12000
PD055 PDC055DF-12000
PD065 PDC065DF-12000
PD085 PDC085DF-12000
PD44SFD PDC044DF-12000
PD66SFD required change: PDC066DF-12000
PD105 service kit (4 cartridges) 12,000 hours PDC105DF-12000
PD135 (2 years) PDC135DF-12000
PD175 PDC175DF-12000
PD215 required change: PDC215DF-12000
PD275 service kit (8 cartridges) 12,000 hours PDC275DF-12000
PD365 (2 years) PDC365DF-12000 kit shown: PDC025-12000
Valve service kit includes:

PD004-PD035 VSKS 01 shuttle seats, shuttles, O-rings, diaphragms and
springs, solenoid valves, controller re-set disc, spare
pressure plugs
PD44SFD/PD66SFD VSKD 01
valve service kit as required
PD045-PD175 PDVSKS 01
PD215-PD365 PDVSKD 01
kit shown: PDVSKD01
Optional software
Energy management, monitoring
All models optional software - PDFS 01 and diagnostics software
PD004-PD035 wall mounting bracket - WKN01804
PD004-PD035 foot mounting bracket - WKN01805
36 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
pro dry accessories PD
dryer
description service interval kit number price
model
JANUARY 2012
Shuttle kit includes:
PD004-PD035 PD1SKS01 shuttle seats, shuttles, exhaust block shuttles,
O-rings and seals
PD044SFD/PD066SFD PD1SKD01
recommended:
shuttle kit 12,000 hours
(2 years)
PD045-PD175 PD2SKS01
PD215-PD365 PD2SKD01
kit shown: PD2SKS01
PD004-PD035 PD1TDKS01 Diaphragm kit includes:

recommended: valve diaphragm and diaphragm spring
top diaphragm kit 12,000 hours
(2 years)
PD044SFD/PD066SFD PD1TDKD01
PD004-PD035 PD1BDKS01
recommended:
bottom diaphragm kit 12,000 hours
(2 years)
PD044SFD/PD066SFD PD1BDKD01
kit shown: PD1TDKD01
PD004 PD1SK01 Silencer kit
PD006-PD035 PD1SK02
PD044SFD/PD066SFD recommended: PD1SK03

silencer kit 6000 hours
PD045-PD085 (1 year) PD2SK01
PD105-PD175 PD2SK02
PD215-PD365 PD2SK03 kit shown: PD2SK01
PD004-PD035 PDCK01 Controller assembly kit includes:

electronic controller complete with solenoid valves
controller assembly kit
PD044SFD/PD066SFD - PDCK01
(with valves)
PD045-PD365 PDCK02
PD1 controller
PD004-PD035 - PDC01
(without valves)
PD2 controller
PD045-PD365 - PDC02 kit shown: PDCK02
(without valves)
Purge plug kit includes:
sized purge plugs and assembled O-rings
All models purge plug kit - PPK004-PPK365
DIN plug kit includes:

DIN plug, gasket and screw
All models DIN plug kit - PDDIN01
technical notes
1 For replacements elements to fit 'Alpha' range XA pre-filter housing please see page 16.
2 For replacements elements to fit 'A' range XA pre-filter housing please see page 43.
3 Help to identify pre-filter models is available, please contact Sales for details.
37
accessories
To accompany our standard
product range, we supply a
range of accessories to suit your
needs.
Accessories includes mounting
brackets, connecting kits,
O-rings, vacuum flasks,
differential pressure monitoring
equipment and a range of drain
options.
This range has been designed
to perform a particular task that
forms a key part of the overall
filtration solution, and has been
manufactured to suit most
applications.
These products help to maintain
equipment to ensure production
levels are maintained and
overheads are not increased.
38 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
COMPRESSED
For safe and reliable condensate drainage systems Walker Filtration supplies a
comprehensive range of float, automatic, manual and electronic drain valves.
ACCESSORIES
AIR DRYERS
drain valve equipment DV
condensate dimensions
pipe size pressure weight complete
model flow rate (mm)
JANUARY 2012
Kg price
inlet outlet Nm³/h SCFM barg psig A B
manually operated drain valves
MDV25 ¼ ¼ - - 20 290 41 50 0.08
MDV50 ½ ½ - - 20 290 46 45 0.12 A A
MDV25CS-50 ¼ ¼ - - 50 725 50 70 0.45 A B A

B
MDV25SS-50 ¼ ¼ - - 50 725 50 70 0.45 B

B
MDV25SS-350 ¼ ¼ - - 350 5075 50 70 0.45

MDV25 MDV25SS-50
PDV 25 ¼ - - - 10 150 35 28 0.45 MDV50 MDV25CS-50 MDV25SS-350 PDV25
float operated automatic / semi automatic drain valves
SDV25 ¼ ¼ - - 16 232 30 15 0.05
DVAS16C - /
1 8 - - 16 232 24 85 0.05 B B B
DVAS16 - /
1 8 - - 16 232 24 85 0.05
A A A
ADV16 - /
1 8 - - 16 232 24 85 0.05 ADV16
DVAS16C DVAS16 ADVA16
ADVA16 - /
1 8 - - 16 232 24 85 0.05 A
ADV3000 - ¼ - - 16 232 39 76 0.02 A

B
ADVK16 Replacement O-ring seal & circlip to fit ADV16 and ADVA16 B
ADV3000 SDV25
solenoid operated drain valves
EDV1000 /
1 8 /
1 8 - - 16 232 83 80 0.45 A
A
EDV2000 - - 16 232 90 73 0.55
EDV2000
¼ ¼ - - 40 580 90 73 0.7 B
B
(40 barg/600 psig)
EDV2000
¼ ¼ - - 80 1160 90 73 0.7
(80 barg/1200 psig)
EDV2211 ¼ ¼ - - 16 232 90 73 0.7 EDV1000 EDV2000 & EDV2211
no loss electronically operated drain valves
BDV12 ½ 392 230 16 232 158 141 0.8 B
BDV13 2x½ ½ 1786 1050 16 232 212 162 2.0 B

A
A
BDV14 3x¾ ½ 7729 4550 16 232 252 180 2.9 A B
BDV31 ½ ¾ 148 87 16 232 118 117 1.0 BDV12 BDV13 & BDV14 BDV31
technical notes
1 BDV models supplied complete with installation kit, which includes mounting brackets, connection kit and
discharge kit.
2 Maximum operating temperature as follows: float operated drain valves 80ºC (176ºF), solenoid operated drain
valves 90ºC (194ºF), no loss electronically operated drain valves 60ºC (140ºF).
3 ADV 16 drain is suitable for previous filter range models A20 and A30.
4 ADV 3000 drain is suitable for previous filter range models A55 to A308.
5 DVAS16C drains are supplied as standard on filter housing models A018 to A058.
6 DVAS16 drains are supplied as standard on filter housing models A059 to A390.
39
Walker Filtration manufactures a comprehensive range of differential pressure
monitoring equipment for air and gas applications.
differential
ACCESSORIES
DP pressure equipment
differential
equipment description complete
55 size 65 size model pressure range
JANUARY 2012
price
mbar d psi d 55 size 65 size grey black white indicator gauge
55DPG250B 250 3.6  - -  - - 
65 40 55DPG1000B 1000 14.5  - -  - - 

88
56 40
107
75 65DPG250B 250 3.6 -  -  - - 
65
32 20 40 20 65DPG250G 250 3.6 -   - - - 
65 40
88
56 40
65DPG700G 700 10.1 -   - - - 
107
65 75
65DPG700B 700 10.1 -  -  - - 
32 20 40 20
65DPG1000B 1000 14.5 -  -  - - 
Images show volt free contact option.

Please see important note below for 65DPG1000G 1000 14.5 -   - - - 
required fixing kit
65 40 55DPIW 700 10.1  - - -   -

88
56 40
107 65DPIB 700 10.1 -  -  -  -
65 75
20
65DPIG 700 10.1 -   - -  -
32 40 20
55DPUB 400 5.8  - -  -  -
65DPUBA 400 5.8 -  -  -  -

48 25 60 25
42 40
65DPUGA 400 5.8 -   - -  -
32 40
65DPUGA-100 100 1.4 -   - -  -
65DPUBA-100 100 1.4 -  -  -  -
WPN4020902 panel mounting kit for all 55 size models
WPN4021002 panel mounting kit for all 65 size models
WPN4021102 mounting block for all 65 size models to fit other housings
GBK059 gauge blanking kit

IMPORTANT: replacement gauges for filter models FK65 fixing kits for A059 - A158
A059 to A390 require a fixing kit. Please reference
the adjacent table for details. FK65L fixing kits for A159 - A390
technical notes
1 Differential pressure indicator and gauge working pressure 20 barg (290 psig).
2 Differential pressure indicator and gauge maximum working temperature 50°C (122°F).
3 Differential pressure indicator and gauge accuracy, + or - 2.5% FSD.
4 Gauge adaptor blocks are available to convert the indicators from standard Walker Filtration mounting
connections to 1/8" or M5.
5 Electrical version differential pressure indicator and gauge switching voltage = 200VDC. Indicator and gauge
switching current = 0.5A. Indicator and gauge carry current = 1.2A. Indicator and gauge switch type = two pole
normally open.
6 For panel mounting a 55 model differential pressure indicator gauge, remove gauge face, cut 50mm hole in
panel and relocate face (not available for 65 models).
7 Volt free contact options available on request on DPG and DPI models only at additional cost. Add 'E' to model
number, for example, 65DPIBE. Volt free contact shown in dotted line on drawings.
40 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
To accompany our standard product portfolio we supply a range of accessories.
ACCESSORIES
accessories
model equipment description to fit equipment model complete price
JANUARY 2012
connecting kits
2CK1 A27, A34, A39, A55, A73, D40, D45
2CK1/1 A20, A30, D20, D30

connecting kit for joining
2CK2 A76, A105, A106, A126
2 filter housings together
2CK2/1 A153, A203, A205
2CK3/1 A250, A305, A306
3CK1 A27, A34, A39, A55, A73, D40, D45
3CK1/1 A20, A30, D20, D30

3CK2 A76, A105, A106, A126
3 filter housings together
3CK2/1 A153, A203, A205
3CK3/1 A250, A305, A306
CNK018 A018, A019
CNK028 A028, A038, A058

CNK059 2 filter housings together A059, A078, A079, A108, A109
CNK128 (for every additional housing A128, A158
CNK159 connection, 1 connection A159, A208, A209

kit is required.
CNK254 For example, 3 connection kits are A254, A340, A360, A390
required to join 4 filter housings)
CNKD028 D028, D038, D058
CNKD059 D059, D078, D079, D108, D109
drain flasks
MLF100 100ml glass flask (polymer coating)
100ml glass flask, plastic screw

MLA100 A018 to A390 VLR, VX1,
cap and ¼" connection/valve
EF, EFC and MV
MLA250

MLA500

MLA1000
41
WALKER ELEMENTS
To accompany our standard product portfolio we supply a range of accessories.

ACCESSORIES
PREVIOUS
accessories
model equipment description to fit equipment model price
JANUARY 2012
mounting bracket kits
MBK1 A27, A50WS, A39, A55, D40, D45, A72
MBK1/1 A20WS, A30WS, A20, A30, D20, D30,

wall mounting bracket,
MBK2 A75WS, A100WS, A125WS, A76, A105, A106
nuts and bolts
MBK2/1 A150WS, A200WS, A153, A203, A126, A205
MBK3/1 A300WS, A250WS, A350WS, A305, A306
MBK50HP 1 50HP25, 50HP37 and 50HP101
MBK50HP 2 wall mounting bracket 50HP50
MBK50HP 3 50HP150 and 50HP201
MBK018 A018, A019
MBK028 A028, A038, A058
MBK059 A059, A078, A079, A108, A109
MBK128 wall mounting bracket, A128, A158
MBK159 nuts and bolts A159, A208, A209
MBK254 A254, A340, A360, A390
MBKD028 D028, D038, D058
MBKD059 D059, D078, D079, D108, D109
'O' ring sealing kits
OSK1 O-ring seal kit, 1 body, A27, A34, A39, A55, A56, A73
OSK1/1 1 drain and 1 element seal A20, A30
OSK2 O-ring seal kit, 2 body, D45
OSK2/1 1 drain and 2 element seal D20, D30
OSK3 A76, A105, A106, A126
OSK3/1 O-ring seal kit, 1 body, A153, A203, A205
OSK4/1 1 drain and 1 element seal A250, A305, A306
OSK5 A308
O-ring seal kit,
OSK6 A400MV
2 flange and 1 body flange seal
OSK7 O-ring seal kit, 4 differential pressure gauge/indicators
OSK8 ¼”, ” high pressure housing kit
OSK9 O-ring seal kit, 1 body 1” high pressure housing kit
OSK10 2” high pressure housing kit
OSK11 C25, C37, C50
OSK12 O-ring sealing kit C75, C101
OSK13 C150, C200, C201, C250
OSK018 A018, A019
OSK028 A028, A038, A058
OSK059 A059, A078, A079, A108, A109
OSK128 A128, A158

O-ring sealing kit
OSK159 A159, A208, A209
OSK254 A254, A340, A360, A390
OSKD028 D028, D038, D058
OSKD059 D059, D078, D079, D108, D109
42 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
PREVIOUS WALKER ELEMENTS
Elements suitable for use in Walker Filtration's earlier ranges of air, gas, medical
vacuum, medical sterile and high pressure filter housings.
previous Walker filter elements

previous compressed air and gas elements previous medical sterile elements
JANUARY 2012
housing reference element reference price housing reference element reference price
A20 E361 (grade) A20 MS E361 SR
A105 E811 (grade) A105 MS E811 SR
A106 E731 (grade) A106 MS E731 SR
A126 E821 (grade) A126 MS E821 SR
A153 E831 (grade) A153 MS E831 SR
A203 E831 (grade) A203 MS E831 SR
A205 E851 (grade) A205 MS E851 SR
A250 E1251 (grade) A250 MS E1251 SR
A305 E1251 (grade) A305 MS E1251 SR
A306 E1261 (grade) A306 MS E1261 SR
A308 E1281 (grade) A308 MS E1281 SR
A25, A35, A40 E50 (grade) A25 MS E50 SR
A38, A45, A70 E51 (grade) A38 MS E51 SR
A74, A75 E71 (grade) A74 MS E71 SR
A100, A124 E81 (grade) A100 MS E81 SR
A141 E831 (grade) A141 MS E831 SR
A150 E103 (grade) A191 MS E831 SR
A200 E123 (grade) A200 MS E123 SR
A201 E125 (grade) A201 MS E125 SR
A202 E134 (grade) A202 MS E134 SR
A250, A291 E135 (grade) A291 MS E135 SR
A300 E127 (grade) A300 MS E127 SR
A301 E128 (grade) A301 MS E128 SR
D25, D38 E01AC
D20 XAC E361 XA / E381 AC
A131, A151 E830 (grade)
A261, A463 E86 (grade) previous medical vacuum elements
A474, A676, A678,
housing reference element reference price
A8710, A10716, E87 (grade)
A12724 A27 MV E27 MV
A361 E137 (grade) A37 MV E37 MV
A371 E138 (grade) A47 MV E57 MV
A77 MV E57 MV
For grades: A100 MV E81 MV
X25, X5, X1, XA, AC, RX25, RX5, A125 MV E83 MV
RX1, RXA, RAC, EF, VX1, VLR.
A150 MV E103 MV
A200 MV E133 MV
A300 MV E137 MV
A301 MV E138 MV
previous high pressure elements A39 MV E511 MV
housing reference element reference price A56 MV E521 MV
350 HP 12 HP 260 (grade) A70 MV E521 MV
A153 MV E831 MV
A205 MV E851 MV
A306 MV E1261 MV
A308 MV E1281 MV
43
New for 2012
Deltech D Series alternative elements &
vacuum pump
Finite J Series
Domnick Hunter Oil-X Evolution
Sullair Range
separators
page
JANUARY 2012
AFE 45
Balston (Parker) 46
Bea Filtri 46
Becker 46
CompAir (Gardner Denver) 47
CTA 48
Deltech (SPX) 49
Dollinger (SPX) 49
Domnick Hunter (Parker) 50-53
Donaldson Ultrafilter 90 Series 54
Edwards 57
Finite (Parker) 58
Gardner Denver 59
Gemoc 59
Hankison (SPX) 60
Hiross (Parker) 61
HPC 62
Hydrovane 62
Ingersoll Rand 63
Kaeser 64
Lacy Hulbert 64
Mattei 65
Mikropor 65
MTA 66
Norgren 67
Omega 67
Pneumatic Products (SPX) 68
Sullair 69
Trocair 70
Zander (Parker) 70
44 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Replacement filter elements manufactured by Walker Filtration Ltd to fit AFE filter
ALTERNATIVE ELEMENTS
housings.
AFE
Grade X5 - 5 micron Grade X1 - 1 micron
JANUARY 2012
walker model replaces price walker model replaces price
AE010X5 EA10P AE010X1 EA10U
Grade XA - 0.01 micron Grade XAA - 0.001 micron

AE010XA EA10H AE010XAA EA10S
EA775XA EA775H EA775XAA EA775S
Grade AC - activated carbon

walker model replaces price
AE010AC EA10C
AE015AC EA15C
AE020AC EA20C
AE030AC EA30C
AE055AC EA55C
AE095AC EA95C
AE150AC EA150C
AE220AC EA220C
AE290AC EA290C
AE430AC EA430C
AE625AC EA625C
AE775AC EA775C
Certified performance
Our entire product range
provides certified performance
levels, guaranteeing that
stringent specifications are
met. Each element is assured
to be ‘equal or superior to’ the
original manufacturers stated
performance and elements are
supplied with a Certificate of
Conformity.
45
Replacement sterile filter elements manufactured by Walker Filtration Ltd to fit
BALSTON (PARKER) sterile gas filter housings.
balston (parker)
BA 15 SR SAC 15
BA 35 SR SAC 35
BA 80 SR SAC 80
BA120 SR SAC 120
BA150 SR SAC 150
JANUARY 2012
Replacement filter elements manufactured by Walker Filtration Ltd to fit BEA FILTRI
filter housings.
bea filtri
Grade X1 - 1 micron filtration Grade XA - 0.01 micron oil removal
BF30 X1 ARS30 RB BF30 XA ARS30 RA
BF0501 X1 FCY0501 RC BF0501 XA FCY0501 RA

BF2001 X1 FCY2001RC BF2001 XA FCY2001 RA
Grade AC - Activated carbon Grade RX1 - 1 micron dust filtration

BF30 AC ARS30 CA BF30 RX1 ARS30 RF
BF0501 AC FCY0501 CA BF0501 RX1 FCY0501 RF

BF2001 AC FCY2001 CA BF2001 RX1 FCY2001RF
Replacement air oil separators manufactured by Walker Filtration Ltd to fit BECKER
vacuum pumps.
becker
Grade PD - 0.01 micron oil removal filter
BE06540100MF 6540100
BE904009MF 904009
BE965402MF 965402
BE965403MF 965403
BE965404MF 965404
BE965406MF 965406
BE965409MF 965409
BE965410MF 965410
BE965411MF 965411
BE965412MF 965412
BE965413MF 965413
BE965414MF 965414
BE965415MF 965415
46 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Replacement filter elements manufactured by Walker Filtration Ltd to fit
COMPAIR (GARDNER DENVER) filter housings.
compair (gardner denver)

Grade X25 - 25 micron filtration Grade X1 - 1 micron filtration Grade XA - 0.01 micron filtration
JANUARY 2012
walker model replaces price walker model replaces price walker model replaces price
COM 0005 X25 CE 0005 A COM 0005 X1 CE 0005 B COM 0005 XA CE 0005 C
Grade ACS - Activated carbon Grade RX1 - 1 micron dust filtration Grade AC - Activated carbon
COM 0005 ACS CE 0005 D COM 0005 RX1 CE 0005 E COM 0004 AC CE0004 D
COM 0198 ACS CE 0198 D COM 0198 RX1 CE 0198 E
Grade X1 - 1 micron filtration Grade OFP - 0.01 micron oil removal Grade OVR - Activated carbon
COM 21 X1 98245/121 COM 41 XA 98245/141 COM 61 AC 98245/161
COM 22 X1 98245/122 COM 42 XA 98245/142 COM 62 AC 98245/162
COM 23 X1 98245/123 COM 43 XA 98245/143 COM 63 AC 98245/163
COM 25 X1 98245/125 COM 45 XA 98245/145 COM 64 AC 98245/164
COM 26 X1 98245/126 COM 46 XA 98245/146 COM 65 AC 98245/165
COM 27 X1 98245/127 COM 47 XA 98245/147 COM 66 AC 98245/166
COM 28 X1 98245/128 COM 48 XA 98245/148 COM 67 AC 98245/167
COM 29 X1 98245/129 COM 49 XA 98245/149 COM 68 AC 98245/168
COM 30 X1 98245/130 COM 50 XA 98245/150 COM 69 AC 98245/169
COM 70 AC 98245/170
Grade GPP - 1 micron filtration Grade OFP - 0.01 micron oil removal Grade OVR - Activated carbon
COM 22 X1 98245/21 COM 42 XA 98245/41 COM 62 AC 98245/62
COM 23 X1 98245/22 COM 43 XA 98245/42 COM 65 AC 98245/65
COM 25 X1 98245/23 COM 45 XA 98245/43 COM 67 AC 98245/67
COM 26 X1 98245/25 COM 46 XA 98245/45 COM 68 AC 98245/68
COM 27 X1 98245/27 COM 47 XA 98245/47
COM 28 X1 98245/28 COM 48 XA 98245/48
COM 29 X1 98245/29 COM 49 XA 98245/49
Solution
With the combination
of our technical ability
and experience, product
performance, competitive
pricing and swift delivery, the
decision is simple.
47
Replacement filter elements manufactured by Walker Filtration Ltd to fit CTA filter
housings.
cta
Grade 1 micron Grade 3 micron Grade 0.01 micron
JANUARY 2012
CT06050M 06050M CT06050P 06050P CT06050S 06050S
CT07050M 07050M CT07050P 07050P CT07050S 07050S
CT12075M 12075M CT12075P 12075P CT12075S 12075S
CT14050M 14050M CT14050P 14050P CT14050S 14050S
CT22075M 22075M CT22075P 22075P CT22075S 22075S
CT32075M 32075M CT32075P 32075P CT32075S 32075S
CT50075M 50075M CT50075P 50075P CT50075S 50075S
CT51090M 51090M CT51090P 51090P CT51090S 51090S
CT75140M 75140M CT75140P 75140P CT75140S 75140S
CT76090M 76090M CT76060P 76090P CT76090S 76090S
Grade Activated carbon

CT07050A 07050A
CT12075A 12075A
CT14050A 14050A
CT22075A 22075A
CT32075A 32075A
CT50075A 50075A
CT51090A 51090A
CT75140A 75140A
CT76090A 76090A
Delivery
Walker Filtration is committed
to a 24 hour despatch service
(on all in stock items) for all
of your alternative elements.
By maintaining optimum
stock levels and ‘off the shelf’
products, we ensure that
wherever you are located in
the world, we can deliver your
order on time.
48 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
DELTECH (SPX) filter housings.
deltech (spx)
Grade E - Dual stage filtration Grade CC - Colour change Grade AC - Activated carbon
JANUARY 2012
DE811E 811E DE110CC DFE110E DE110AC DE110KE
DE816E 816E
DE817E 817E
DE818E 818E
DE819E 819E
DE820E 820E
DE830E 830E
DE831E 831E
Grade AC - Activated carbon

walker model replaces price Grade: walker model replaces price
DE850 (grade) 850 (grade) X1 replaces grade PFD (1 micron filter) DE850AC 850CFD
DE851 (grade) 851 (grade) XA replaces grade HFD (0.01 micron filter) DE853AC 853CFD
DE852 (grade) 852 (grade) AC replaces grade CFD (activated carbon filter) DE854AC 854CFD
DE870 (grade) 870 (grade) RX1 replaces grade DFD (1 micron dust filter) DE873AC 873CFD
DE871 (grade) 871 (grade) DE874AC 874CFD
DE113 (grade) 8113 (grade) DE121AC-OS 121CFD-OS
DE201 (grade) 8201 (grade)
DE202 (grade) 8202 (grade)
New for 2012

Deltech D Series
Grade RX1 - 1 Micron particulate removal

walker model replaces price Grade: walker model replaces price
DE0005 (grade) D-0005 (grade)
X1 replaces grade CCE (1 micron general purpose) DE0010 RX1 D-0010 PFE
DE0010 (grade) D-0010 (grade) XA replaces grade CFE (0.01 micron high efficiency) DE0020 RX1 D-0020 PFE
DE0020 (grade) D-0020 (grade) AC replaces grade VFE (activated carbon filter) DE0050 RX1 D-0050 PFE
DE0050 (grade) D-0050 (grade) DE0100 RX1 D-0100 PFE

DOLLINGER (SPX) filter housings.
dollinger (spx)
D006 (grade) 501130 (grade) D006 AC 501130
D013 (grade) 501135 (grade) D013 AC 501135
D025 (grade) 501177 (grade) D025 AC 501177
D040 (grade) 501210 (grade) D040 AC 501210
D085 (grade) 501254 (grade) D085 AC 501254
D195 (grade) 501455 (grade) D195 AC 501455
D400 (grade) 501494 (grade) D400 AC 501494
D500 (grade) 501375 (grade) D500 AC 501375
49
AIR DRYERS
Replacement current filter elements manufactured by Walker Filtration Ltd to fit

COMPRESSED ELEMENTS
housings made by DOMNICK HUNTER (PARKER) Ltd.

ALTERNATIVE
domnick hunter (parker)

Grade EX1 - 1 micron filtration Grade EXA - 0.01 micron / 0.01mg/m³ oil removal
JANUARY 2012

D005 EX1 005AO D005 EXA 005AA
D010 EX1 010AO D010 EXA 010AA
D015 EX1 015AO D015 EXA 015AA
D020 EX1 020AO D020 EXA 020AA
New for 2012 D025 EX1 025AO D025 EXA 025AA
domnick hunter oil-x evolution D030 EX1 030AO D030 EXA 030AA
D035 EX1 035AO D035 EXA 035AA
D040 EX1 040AO D040 EXA 040AA
D045 EX1 045AO D045 EXA 045AA
D050 EX1 050AO D050 EXA 050AA
D055 EX1 055AO D055 EXA 055AA
D060 EX1 060AO D060 EXA 060AA
Grade ERX1 - 1 micron dust filtration Grade ERXA - 0.01 micron dust removal
D005 ERX1 005AR D005 ERXA 005AAR
Grade EACS - Activated carbon

D005 EACS 005ACS
D010 EACS 010ACS
D015 EACS 015ACS
D020 EACS 020ACS
D025 EACS 025ACS
D030 EACS 030ACS
D035 EACS 035ACS
D040 EACS 040ACS
D045 EACS 045ACS
D050 EACS 050ACS
D055 EACS 055ACS
D060 EACS 060ACS
50 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748

Previous filter elements references
JANUARY 2012
Grade X25 - 25 micron pre filter Grade X1 - 1 micron filtration Grade XA - 0.01 micron / 0.01mg/m³ oil removal
D009 X25 K009PF D009 X1 K009AO D009 XA K009AA
Grade XAA - 0.001 micron / 0.001 mg/m³ oil removal Grade ACS - Activated carbon Grade AC - Activated carbon
D009 XAA K009AX D009 ACS K009ACS D006 AC K006AC
D330 XAA K330AX D330 ACS K330ACS
Grade MV - Medical vacuum Hopcolite replacement elements

D025 MV K025PL D013 HC K013HC
D195 MV K195PL
D400 MV K400PL
Grade X25 - 25 micron pre filter Grade X1 - 1 micron filtration Grade XA - 0.01 micron / 0.01 mg/m³ oil removal
Grade ACS - Activated carbon Grade XAA - 0.001 micron / 0.001 mg/m³ oil removal
D006 ACS K006ACS D006 XAA K006AX
technical notes
All replacement filter elements supplied against
Domnick Hunter ‘K’ references are supplied with
O-ring kits.
51

JANUARY 2012
Grade X25 - 25 micron pre filter Grade X1 - 1 micron filtration Grade XA - 0.01 micron oil removal
D007 X25 K007PF D3 X1 C3MS D2 XA C2EPO
D060 X25 K060PF D12 DX1 C12 MSD D8 XA C8EPO
D200 X25 K200PF D12 BX1 C12MSDB D24 XA C24EPO
D250 X25 K250PF D24 BX1 C24MSDB D12 DXA C12D
D300 X25 K300PF D155 X1 C155MSD D12B XA C12DB
D360 X25 K360PF D185 X1 C185MSD D24B XA C24DB
D245 X1 C245MSD D155 XA C155D
D185 XA C185D
D007 X1 K007AO D245 XA C245D
D011 X1 K011AO D305 XA C305D
D035 X1 K035AO
D060 X1 K060AO D007 XA K007AA
D120 X1 K120AO D011 XA K011AA
D200 X1 K200AO D035 XA K035AA
D250 X1 K250AO D060 XA K060AA
D300 X1 K300AO D120 XA K120AA
D360 X1 K360AO D200 XA K200AA
D250 XA K250AA
D300 XA K300AA
D360 XA K360AA
Grade AC - Activated carbon Grade AS - Sterile filters Grade MV - Medical vacuum

D4 AC C4AC D 2AS C 2ME & MESR D3 MV C3CT
D12 ACB C12ACDB D 8AS C 8ME & MESR D12 MV C12CT
D24 ACB C24ACDB D 12AS C12ME & MESR D12 BMV C12CTDB
D155 AC C155ACD D 12ASB C12MERBSR D24 BMV C24CTDB
D245 AC C245ACD D 24AS C24ME & MESR D125 MV C125CTD
D 24ASB C24MERBSR D155 MV C155CTD
D011 AC ABN 1 D 36ASB C36MERBSR D185 NFBMV C185CTD
D011 AC E011AC D245 MV C245CTD
D060 AC E060AC D011 MV E011CT
52 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748

JANUARY 2012
Ammonia filter elements (NH³) - 1 micron Ammonia filter elements (NH³) - 0.01 micron
D12BX1NH³ C12MSDBNH³ D12BXANH³ C12DBNH³
D24BX1NH³ C24MSDBNH³ D24BXANH³ C24DBNH³
D245BX1NH³ C245MSDNH³ D245XANH³ C245DNH³
D120X1NH³ E120AONH³ D120XANH³ E120AANH³
Grade ASR - Sterile filters

D2 ASR MER2SRH/MER2SRL
D3 ASR MER3SRH/MER3SRL
D4 ASR MER4SRH
D8 ASR MER8SRH
D12 ASR MER12SRH
D24 ASR MER24SRH
High temperature requirement filter elements
Grade TX1 - 1 micron high temperature Grade TXA - 0.01 micron high temperature
D4 TX1 C4MSTS D2 TXA C2TS
D12 BTX1 C12MSDTS D8 TXA C8TS
D24 BTX1 C24MSDBTS D12 TXA C12TS
D155 TX1 C155MSDTS D12 BTXA C12DBTS
D185 TX1 C185MSDTS D24 BTXA C24DBTS
D245 TX1 C245MSDTS D155 TXA C155DTS
D185 TXA C185DTS
D007 TX1 E007AOTS D245 TXA C245DTS
D011 TX1 E011AOTS D305 TXA C305DTS
D035 TX1 E035AOTS D007 TXA E007AATS
D195 TX1 K195AOTS D085 TXA E085AATS
D250 TX1 E250AOTS D195 TXA K195AATS
D295 TX1 K295AOTS D200 TXA E200AATS Certified performance
D360 TX1 E360AOTS D295 TXA K295AATS Our entire product range
D500 TX1 K500AOTS D300 TXA E300AATS provides certified performance
D360 TXA E360AATS
D500 TXA K500AATS levels, guaranteeing that
stringent specifications are
met. Each element is assured
to be ‘equal or superior to’ the
original manufacturers stated
performance and elements are
supplied with a Certificate of
Conformity.
53
DONALDSON ULTRAFILTER 90 series.
donaldson ultrafilter 90 series

Grade UV - 25 micron pre filter Grade UFF - 1 micron oil removal Grade UMF - 0.1 micron oil removal
JANUARY 2012
UV 0205 V-PE 02/05 UFF 0205 FF 02/05 UMF 0205 MF 02/05
UV 1030 V-PE 10/30 UFF 1030 FF10/30 UMF 1030 MF 10/30
Grade USM - 0.01 micron oil removal Grade UAC - Activated carbon Grade USR - Sterile filters
USM 0205 SMF 02/05 UAC 0205 AK 02/05 USR 0205 SRF 02/05
Replacement elements for

Donaldson Ultrafilter 90 series HT/CR or HT/NX ordering information
walker model replaces price Walker Filtration supply both threaded (USR) and
UFF/UMF/USM 0205* FF/MF/SMF 02/05 push-fit (UPSR) replacement filter elements.
UFF/UMF/USM 0305* FF/MF/SMF 03/05 Please indicate your preference when ordering.
UFF/UMF/USM 0310* FF/MF/SMF 03/10
* Please indicate grade required
54 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748

Grade UV - 25 micron pre filter Grade UFF - 1 micron oil removal Grade UMF - 0.1 micron oil removal
JANUARY 2012
UV 310 V 3/1 UFF 310 FF 3/1 UMF 310 MF 3/1
UV 315 V 3/1.5 UFF 315 FF 3/1.5 UMF 315 MF 3/1.5
UV 415 V 4/1.5 UFF 415 FF 4/1.5 UMF 415 MF 4/1.5
UV 425 V 4/2.5 UFF 425 FF 4/2.5 UMF 425 MF 4/2.5
UV 525 V 5/2.5 UFF 525 FF 5/2.5 UMF 525 MF 5/2.5
UV 530 V 5/3 UFF 530 FF 5/3 UMF 530 MF 5/3
UV 103 V 10/3 UFF 103 FF10/3 UMF 103 MF10/3
UV 153 V 15/3 UFF 153 FF15/3 UMF 153 MF15/3
UV 203 V 20/3 UFF 203 FF20/3 UMF 203 MF20/3
UV 303 V 30/3 UFF 303 FF30/3 UMF 303 MF30/3
UV 305 V 30/5 UFF 305 FF30/5 UMF 305 MF30/5
Grade USM - 0.01 micron oil removal Grade UAC - Activated carbon Grade USR - Sterile filters
USM 315 SMF 3/1.5 UAC 315 AK 3/1.5 USR 315 SRF 3/1.5
USM 103 SMF10/3 UAC 103 AK10/3 USR 103 SRF10/3
Replacement elements for Donaldson Ultrafilter 80 series HT/CR or HT/NX ordering information
Walker Filtration supply both threaded (USR) and
push-fit (UPSR) replacement filter elements.
UFF/UMF/USM 310* 3/1 FF/MF/SMF
Please indicate your preference when ordering.
UFF/UMF/USM 315* 3/1.5 FF/MF/SMF
* Please indicate grade required
55

Grade UPE - 25 micron pre filter Grade UFF - 1 micron pre-filter Grade UMF - 0.1 micron oil removal
JANUARY 2012
UPE 215 V-PE 2/1.5 UFF 215 FF 2/1.5 UMF 215 MF 2/1.5
UPE 415 V-PE 4/1.5 UFF 415 FF 4/1.5 UMF 415 MF 4/1.5
UPE 43 V-PE 4/3 UFF 43 FF 4/3 UMF 43 MF 4/3
UPE 1231S V-PE 12/3 1"S UFF 1231S FF 12/3 1"S UMF 1231S MF 12/3 1"S
UPE 1231G V-PE 12/3 1"G UFF 1231G FF 12/3 1"G UMF 1231G MF 12/3 1"G
UPE 2431G V-PE 24/3 1"G UFF 2431G FF 24/3 1"G UMF 2431G MF 24/3 1"G
Grade UOL - 0.01 micron oil removal Grade UAC - Activated carbon Grade USR - Sterile filters
UOL 215 OL 2/1.5 UAC 215 AK 2/1.5 USR 215 SRF 2/1.5
UOL 415 OL 4/1.5 UAC 415 AK 4/1.5 USR 215S SRF 2/1.5S
UOL 43 OL 4/3 UAC 43 AK 4/3 USR 415 SRF 4/1.5
UOL 83 OL 8/3 UAC 83 AK 8/3 USR 415S SRF 4/1.5S
UOL 1231G OL 12/3 1"G UAC 1231G AK 12/3 1"G USR 43 SRF 4/3
UOL 1231S OL 12/3 1"S UAC 1232S AK 12/3 2"S USR 43S SRF 4/3S
UOL 1232G OL 12/3 2"G UAC 203 AK 20/3 USR 83 SRF 8/3
UOL 2431G OL 24/3 1"G UAC 205 AK 20/5 USR 83S SRF 8/3S
UOL 2431S OL 24/3 1"S USR 1231G SRF 12/3 1"G
UOL 2432S OL 24/3 2"S USR 123S SRF 12/3S
UOL 155 OL 15/5 USR 1232G SRF 12/3 2"G
UOL 245 OL 24/5 USR 2431G SRF 24/3 1"G
USR 2432G SRF 24/3 2"G
USR 245 SRF 24/5
56 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Replacement mist eliminators manufactured by Walker Filtration Ltd to fit EDWARDS
vacuum pumps.
edwards
JANUARY 2012
EMF3 A223-04-197 EMF717 A223-04-057
EMF3 A223-04-080 E825MF A223-04-020
EMF3AC A223-04-081 E837MF A223-04-021
EMF10 A223-04-198
EMF10 A223-04-078
EMF10AC A223-04-079
EMF20 A223-04-199
EMF20 A223-04-076
EMF20AC A223-04-077
EMF30 A223-04-057
Customer Service
As filtration specialists, Walker
Filtration manufactures
and supplies one of the
most comprehensive and
competitively priced ranges
of alternative filter elements,
air/oil separators and vacuum
pump separators in the market
today.
57
FINITE (PARKER) filter housings.
finite (parker)
CU - Coalescing borosilicate glass microfibre tube QU - Additional outer pleated pre-filter (*) = Grade:
12 - Efficiency rating 90% at 3 micron
JANUARY 2012

FN 10025CU (*) (*) CU 10 025 FN 10025QU (*) (*) QU 10 025 10 - Efficiency rating 95% at 2 micron
FN 10050CU (*) (*) CU 10 050 FN 10050QU (*) (*) QU 10 050 8 - Efficiency rating 98.5% at 1 micron
FN 15060CU (*) (*) CU 15 060 FN 15060QU (*) (*) QU 15 060 6 - Efficiency rating 99.97% at 0.75 micron
FN 15095CU (*) (*) CU 15 095 FN 15095QU (*) (*) QU 15 095
4 - Efficiency rating 99.995% at 0.6 micron
FN 20130CU (*) (*) CU 20 130 FN 20130QU (*) (*) QU 20 130
FN 20187CU (*) (*) CU 20 187 FN 20187QU (*) (*) QU 20 187 2 - Efficiency rating 99.9999+% at 0.4 micron
FN 25130CU (*) (*) CU 25 130 FN 25130QU (*) (*) QU 25 130
FN 25187CU (*) (*) CU 25 187 FN 25187QU (*) (*) QU 25 187 CU - Coalescing borosilicate glass microfibre
FN 25235CU (*) (*) CU 25 235 FN 25235QU (*) (*) QU 25 235 tube and rigid support cylinder. Includes
FN 25280CU (*) (*) CU 25 280 FN 25280QU (*) (*) QU 25 280 polyurethane moulded end caps.
FN 35280CU (*) (*) CU 35 280 FN 35280QU (*) (*) QU 35 280
FN 51280CU (*) (*) CU 51 280 FN 51280QU (*) (*) QU 51 280 QU - Coalescing borosilicate glass microfibre tube,
FN 85250CU (*) (*) CU 85 250 FN 85250QU (*) (*) QU 85 250 with rigid support cylinder and an additional
FN 85360CU (*) (*) CU 85 360 FN 85360QU (*) (*) QU 85 360 outer pleated pre-filter is fitted to models FN
51280 to FN 85360. Includes polyurethane
moulded end caps.
3PU - Pleated pre-filter Grade AC - Efficiency rating 0.003 ppm oil vapour removal
FN 10025PU 3 PU 10 025 FN 10025AU AU 10 025 3PU - Pleated pre-filter with polyurethane moulded
FN 10050PU 3 PU 10 050 FN 10050AU AU 10 050 end caps.
FN 15060PU 3 PU 15 060 FN 15060AU AU 15 060
FN 15095PU 3 PU 15 095 FN 15095AU AU 15 095 AU - Activated carbon odour removal filter element
FN 20130PU 3 PU 20 130 FN 20130AU AU 20 130 with moulded polyurethane end caps.
FN 20187PU 3 PU 20 187 FN 20187AU AU 20 187
FN 25130PU 3 PU 25 130 FN 25130AU AU 25 130
FN 25187PU 3 PU 25 187 FN 25187AU AU 25 187
FN 25235PU 3 PU 25 235 FN 25235AU AU 25 235
FN 25280PU 3 PU 25 280 FN 25280AU AU 25 280
FN 35280PU 3 PU 35 280 FN 35280AU AU 35 280
FN 51280PU 3 PU 51 280 FN 51280AU AU 51 280
FN 85250PU 3 PU 85 250 FN 85250AU AU 85 250
FN 85360PU 3 PU 85 360 FN 85360AU AU 85 360
New for 2012

Finite J Series
(*) = Grade:
FN 11035 (*) (*) CWC 11-035
10 - Efficiency rating 95% at 2 micron
FN 11072 (*) (*) CWC 11-072 8 - Efficiency rating 98.5% at 1 micron
FN 15070 (*) (*) CWC 15-070 6 - Efficiency rating 99.97% at 0.75 micron
FN 23130 (*) (*) CWC 23-130 4 - Efficiency rating 99.995% at 0.6 micron
58 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
GARDNER DENVER filter housings.
gardner denver
JANUARY 2012
GD12 (grade) E FIL12 (grade) E
Grade:
X1 replaces grade C (1 micron filter)
RX1 replaces grade D (dust 1 micron)
XA replaces grade E (0.01 micron)
XAA replaces grade F (0.001 micron)
AC replaces grade G (activated carbon)
Replacement filter elements manufactured by Walker Filtration Ltd to fit GEMOC

filter housings.
gemoc
GF0501 AC 501 GF0501 (grade) 501
GF0701 AC 701 GF0701 (grade) 701
GF1401 AC 1401 GF1401 (grade) 1401
GF1151 AC 1151 GF1151 (grade) 1151
GF1501 AC 1501 GF1501 (grade) 1501
GF3001 AC 3001 GF3001 (grade) 3001
GF4101 AC 4101 GF4101 (grade) 4101
GF6001 AC 6001 GF6001 (grade) 6001
GF6101 AC 6101 GF6101 (grade) 6101
Grade:
X5 replaces grade V (5 micron dust filter)
XO replaces grade M (0.1 micron coalescing)
XA replaces grade S (0.01 micron coalescing)
RX5 replaces grade N (3 micron after filter)
AC replaces grade A (Activated Carbon)
59
HANKISON (SPX) filter housings.
hankison (spx)
1 micron filter 0.01 micron oil removal Activated carbon
JANUARY 2012
HK07313P 0731-3 HK07132C 0713-2 HK07152AC 0715-2
HK07314P 0731-4 HK07133C 0713-3 HK07153AC 0715-3
HK07315P 0731-5 HK07134C 0713-4 HK07154AC 0715-4
HK07316P 0731-6 HK07135C 0713-5 HK07155AC 0715-5
HK07317P 0731-7 HK07136C 0713-6 HK07156AC 0715-6
HK07318P 0731-8 HK07137C 0713-7 HK07157AC 0715-7
HK07319P 0731-9 HK071311C 0713-11 HK071511AC 0715-11
HK071312C 0713-12 HK071312AC 0715-12
1 micron filter 0.01 micron oil removal Activated carbon

HK27313P 27313 HK27132C 27132 HK27152AC 27152
HK27314P 27314 HK27133C 27133 HK27153AC 27153
HK27315P 27315 HK27134C 27134 HK27154AC 27154
HK27316P 27316 HK27135C 27135 HK27155AC 27155
HK27317P 27317 HK27136C 27136 HK27156AC 27156
HK27318P 27318 HK27137C 27137 HK27157AC 27157
HK27319P 27319 HK21311C 21311 HK21511AC 21511

HK (grade) -12 E (grade) - 12 Grade:
HK (grade) -16 E (grade) - 16 X5 replaces grade 9 (5 micron filter)
HK (grade) -20 E (grade) - 20 X1 replaces grade 7 (1 micron filter)
HK (grade) -24 E (grade) - 24 XA replaces grade 5 (0.01 micron filter)
HK (grade) -28 E (grade) - 28 XAA replaces grade 3 (0.001 micron filter)
HK (grade) -32 E (grade) - 32 AC replaces grade 1 (activated carbon)
HK (grade) -36 E (grade) - 36
HK (grade) -PV E (grade) - PV
60 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
HIROSS (PARKER) filter housings.
hiross (parker)
JANUARY 2012
walker replaces replaces price
model 1999 2000/01
H004 (grade) 004 10

H006 (grade) 006 10
H007 (grade) 007 16
H009 (grade) 009 16
H015 (grade) 015 22
H018 (grade) 018 22
H020 (grade) 020 22
H024 (grade) 024 30
H035 (grade) 035 45
H060 (grade) 060 72
H062 (grade) 062 72
H090 (grade) 090 135
H110 (grade) 110 135
H120 (grade) 120 205
H122 (grade) 122 135
H150 (grade) 150 250
H151 (grade) 151 205
H180 (grade) 180 250
H200 (grade) 200 260
H240 (grade) 240 280
H280 (grade) 280 280
H300 (grade) 300 300
Grade:
X1 replaces grade P (general purpose)
XA replaces grade S (oil removal)
AC replaces grade C (Activated carbon)
Grade X5 - 5 micron filter

walker replaces replaces price
model 1999 2000/01
H004 X5 004 Q 10
H006 X5 006 Q 10
H007 X5 007 Q 16
H009 X5 009 Q 16
H015 X5 015 Q 22
H018 X5 018 Q 22
H020 X5 020 Q 22
H024 X5 024 Q 30
H035 X5 035 Q 45
H060 X5 060 Q 72
H062 X5 062 Q 72
H090 X5 090 Q 135
H110 X5 110 Q 135
H120 X5 120 Q 205
H122 X5 122 Q 135
H150 X5 150 Q 250
H151 X5 151 Q 205
H180 X5 180 Q 250
H200 X5 200 Q 260
H240 X5 240 Q 280
H280 X5 280 Q 280
H300 X5 300 Q 300
61
Replacement filter elements manufactured by Walker Filtration Ltd to fit HPC filter
housings.
hpc
Grade X1 - 1 micron filter Grade XA - 0.01 micron oil removal Grade X1 - 1 micron filtration
JANUARY 2012
D009 X1 K009 AO D009 XA K009 AA D006 X1 K006 AO
Grade XA - 0.01 micron oil removal Grade AC - Activated carbon

D006 XA K006 AA D006 AC K006 AC
D013 XA K013 AA D013 AC K013 AC
D025 XA K025 AA D025 AC K025 AC
D040 XA K040 AA D040 AC K040 AC
D085 XA K085 AA D065 AC K065 AC
D195 XA K195 AA D085 AC K085 AC
D295 XA K295 AA D195 AC K195 AC
D400 XA K400 AA D295 AC K295 AC
D500 XA K500 AA D400 AC K400 AC
D500 AC K500 AC
Replacement air oil separators and filter elements manufactured by Walker Filtration
Ltd to fit HYDROVANE filter housings.
hydrovane
Replacement air oil separators
walker model replaces air compressor model no. no. of separators price
HY52022W 52022 6/12 1
HY3415W 3415 13/23/33 1
HY3407W 3407 43/48 1
HY52471W 52471 66 3
HY3415W 3415 120/140 5
HY52471W 52471 170 8
HY3415W 3415 250 10
HY3415W 3415 350/450 12
HY57029W 57029 5/15/25 1
HY59177W 59177 37/47/705/707 1
HY70166W 70166W 128/148/178/218 1
HY70539W 70539 68/88/711/715 2
HY3407W 3407 128<8HV/148<6HV 3
HY59180W 59180 128+9HV/148+7HV 2
HY3407W 3407 178<6HV 3
HY59180W 59180 178+7HV 3
Grade X1/RX1 - 1 micron filtration Grade XA - 0.01 micron oil removal Grade AC - Activated carbon
HY 100 X1/RX1 GP/DR 100 E HY 100 XA HE 100 E HY 100 AC OR 100 E
HY 600 AC OR 600 E
Note:
X1 - General purpose / RX1 - Dust filter
62 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
INGERSOLL RAND filter housings.
ingersoll rand
Grade X1/RX1 - 1 micron oil removal Grade XA - 0.01 micron oil removal Grade ACS - Activated carbon
JANUARY 2012
IRE 5 X1/RX1 5 AO/AR IRE 5 XA 5 AA IRE 5 ACS 5 ACS
Grade X1/RX1 - 1 micron oil filtration Grade XA - 0.01 micron oil filtration Grade AC - Activated carbon
IRE 4 X1/RX1 K4 AO/AR IRE 4 XA K4 AA IRE 4 AC K4 AC
IRE 300 AC K300 AC
Note:
X1 - General purpose / RX1 - Dust filter
Support
Walker Filtration has one
of the most comprehensive
technical libraries to support
all alternative element queries.
63
Replacement filter elements manufactured by Walker Filtration Ltd to fit KAESER filter
housings.
kaeser
Grade X5 - 5 micron Grade X1 - 1 micron Grade XA - 0.01 micron
JANUARY 2012
KSB 006 X5 E-B-6 KSC 006 X1 E-C-6 KSE 006 XA E-E-6
Grade XAA - 0.001 micron Grade AC - Activated carbon Grade RX1 - 1 micron dust filter
KSF 006 XAA E-F-6 KSG 006 AC E-G-6 KSD 006 RX1 E-D-6
Note: For old style Kaeser elements, please

contact Walker Filtration Ltd.
Replacement air/oil separators manufactured by Walker Filtration Ltd to fit

LACY HULBERT vacuum pumps.
lacy hulbert
walker o.d. length replaces price
model
LH 718MF 65mm / 182mm 934000-21
LH 724MF 65mm / 240mm 934000-18
LH 730MF 65mm / 300mm 934000-19
LH 750MF 65mm / 487mm 934000-20
64 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Replacement air oil separators manufactured by Walker Filtration Ltd to fit MATTEI air
compressors.
mattei
JANUARY 2012
M20113W CR2201130
M30725W CR21F30725
M30724W CR21A30724
M30733W CR21H30733
M32486W CR21132486

MIKROPOR filter housings.
mikropor
Grade X3 - 3 micron Grade X1 - 1 micron
MPR48X3 M48P MPR48X1 M48X
MPR1210X3 M1201P MPR1210X1 M1210X
MPR1510X3 M1510P MPR1510X1 M1510X
MPR1810X3 M1810P MPR1810X1 M1810X
MPR2210X3 M2210P MPR2210X1 M2210X
Grade XA - 0.01 micron Grade AC - activated carbon

MPR48XA M48Y MPR48AC M48A
65
Replacement filter elements manufactured by Walker Filtration Ltd to fit MTA filter
housings.
mta
Grade - 1 micron Grade - 3 micron
JANUARY 2012
MT06050M 06050M MT06050P 06050P

MT07050M 07050M MT07050P 07050P
MT14050M 14050M MT14050P 14050P
MT12075M 12075M MT12075P 12075P
MT22075M 22075M MT22075P 22075P
MT32075M 32075M MT32075P 32075P
MT50075M 50075M MT50075P 50075P
MT51090M 51090M MT51090P 51090P
MT75140M 75140M MT75140P 75140P
MT76090M 76090M MT76090P 76090P
Grade - 0.01 micron Grade - Activated carbon

MT06050S 06050S MT06050A 06050A
MT07050S 07050S MT07050A 07050A
MT14050S 14050S MT14050A 14050A
MT12075S 12075S MT12075A 12075A
MT22075S 22075S MT22075A 22075A
MT32075S 32075S MT32075A 32075A
MT50075S 50075S MT50075A 50075A
MT51090S 51090S MT51090A 51090A
MT75140S 75140S MT75140A 75140A
MT76090S 76090S MT76090A 76090A
66 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Replacement filter elements manufactured by Walker Filtration Ltd to fit NORGREN
filter housings.
norgren
Grade AC - Activated carbon Grade XA - 0.01 micron oil removal
JANUARY 2012
N66570AC 665-70 N66572XA 665-72
N66571AC 665-71 N66573XA 665-73
N66585AC 665-85 N66574XA 665-74
N66586AC 665-86 N66579XA 665-79
N66594AC 665-94 N66580XA 665-80
N66581XA 665-81
N66587XA 665-87
N66588XA 665-88
N66591XA 665-91
Note: N66592XA 665-92
Filter element models N66591XA and N66592XA N535005XA 5350-05
do not include sintered bronze pre filter. N535006XA 5350-06
N535098XA 5350-98
N535099XA 5350-99
N535105XA 5351-05
N535106XA 5351-06
N535198XA 5351-98
N535199XA 5351-99
Replacement filter elements manufactured by Walker Filtration Ltd

to fit OMEGA
omega
Grade X3 Grade X1 Grade X0
OE06050X3 06050P OE06050X1 06050R OE06050X0 06050M
OE07050X3 07050P OE07050X1 07050R OE07050X0 07050M
OE14050X3 14050P OE14050X1 14050R OE14050X0 14050M
OE12075X3 12075P OE12075X1 12075R OE12075X0 12075M
OE22075X3 22075P OE22075X1 22075R OE22075X0 22075M
OE32075X3 32075P OE32075X1 32075R OE32075X0 32075M
OE50075X3 50075P OE50075X1 50075R OE50075X0 50075M
OE51090X3 51090P OE51090X1 51090R OE51090X0 51090M
OE76090X3 76090P OE76090X1 76090R OE76090X0 76090M
OE51140X3 51140P OE51140X1 51140P OE51140X0 51140M
OE75140X3 75140P OE75140X1 75140R OE75140X0 75140M
Grade XA Grade AC
OE06050XA 06050S OE06050AC 06050A Delivery
OE07050XA 07050S OE07050AC 07050A
OE14050XA 14050S OE14050AC 14050A Walker Filtration is committed
OE12075XA 12075S OE12075AC 12075A to a 24 hour despatch service
OE22075XA 22075S OE22075AC 22075A
(on all in stock items) for all
OE32075XA 32075S OE32075AC 32075A
OE50075XA 50075S OE50075AC 50075A of your alternative elements.
OE51090XA 51090S OE51090AC 51090A By maintaining optimum
OE76090XA 76090S OE76090AC 76090A
OE51140XA 51140S OE51140AC 51140A
stock levels and ‘off the shelf’
OE75140XA 75140S OE75140AC 75140A products, we ensure that
wherever you are located in
the world, we can deliver your
order on time.
67
Replacement filter elements manufactured by Walker Filtration Ltd
to fit PNEUMATIC PRODUCTS (SPX).
pneumatic products (spx)

JANUARY 2012

P1A02SX PPFK1A02SU
P1A03SX PPFK1A03SU
P1A03EX PPFK1A03AF
P1A05SX PPFK1A05SU
P1A05EX PPFK1A05AF
P2A05SU PPFK2A05SU
P2A07SX PPFK2A07SU
P2A10SX PPFK2A10SU
P2A10EX PPFK2A10AF
P3A11SX PPFK3A11SU
P3A13SX PPFK3A13SU
P3A13EX PPFK3A13AF
P1201SX POS 1201 SU
P1201EX PCS 1201 AF
P1001AC MCS 1001 CE
Original filter elements manufactured by PNEUMATIC PRODUCTS (SPX).
model price
PPFK1A03HT
PPFK1A05HT
PPFK2A10HT
PPFK3A13HT
PCS 1201 HT
Grade:
SU 0.6 Micron Absolute Super Ultipor
(Coalescing Filter)
HT 0.9 Micron Absolute High Temperature
(230°C) following heat reactivated dryer
AF 0.9 Micron Absolute After Filter
CE 0.9 Micron Absolute Carbon Epocel
68 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
Replacement filter elements manufactured by Walker Filtration Ltd to fit SULLAIR
housings.
sullair
Grade - 1 micron Grade - 0.01 micron Grade - Activated carbon
JANUARY 2012
SU250024423X1 250024-423 SU250024431XA 250024-431 SU250024439AC 250024-439
SU250024424X1 250024-424 SU250024432XA 250024-432 SU250024440AC 250024-440
SU250024425X1 250024-425 SU250024433XA 250024-433 SU250030646AC 250030-646
SU250024426X1 250024-426 SU250024434XA 250024-434 SU250024441AC 250024-441
SU250024427X1 250024-427 SU250024435XA 250024-435
SU250024428X1 250024-428 SU250024436XA 250024-436
SU250024429X1 250024-429 SU250024437XA 250024-437
SU250030644X1 250030-644 SU250030655XA 250030-655
SU250024430X1 250024-430 SU250024438XA 250024-438
Grade - Activated carbon

SU250024443ACS 250024-443
SU250024444ACS 250024-444
SU250024445ACS 250024-445
SU250024446ACS 250024-446
SU250024447ACS 250024-447
Grade X1 - 1 micron filtration Grade XA - 0.01 micron / 0.01mg/m³ oil removal

New for 2012
Sullair Range
SU02250153288X1 02250153-288 SU02250153299XA 02250153-299
SU02250153289X1 02250153-289 SU02250153300XA 02250153-300
SU02250153290X1 02250153-290 SU02250153301XA 02250153-301
SU02250153291X1 02250153-291 SU02250153302XA 02250153-302
SU02250153292X1 02250153-292 SU02250153303XA 02250153-303
SU02250153293X1 02250153-293 SU02250153304XA 02250153-304
SU02250153294X1 02250153-294 SU02250153305XA 02250153-305
SU02250153295X1 02250153-295 SU02250153306XA 02250153-306
SU02250153296X1 02250153-296 SU02250153307XA 02250153-307
SU02250153297X1 02250153-297 SU02250153308XA 02250153-308
SU02250153298X1 02250153-298 SU02250153309XA 02250153-309
Grade RX1 - 1 micron dust filtration Grade RXA - 0.01 micron dust removal
SU02250153321RX1 02250153-321 SU02250153332RXA 02250153-332
SU02250153322RX1 02250153-322 SU02250153333RXA 02250153-333
SU02250153323RX1 02250153-323 SU02250153334RXA 02250153-334
SU02250153324RX1 02250153-324 SU02250153335RXA 02250153-335
SU02250153325RX1 02250153-325 SU02250153336RXA 02250153-336
SU02250153326RX1 02250153-326 SU02250153337RXA 02250153-337
SU02250153327RX1 02250153-327 SU02250153339RXA 02250153-339
SU02250153328RX1 02250153-328 SU02250153340RXA 02250153-340
SU02250153329RX1 02250153-329 SU02250153341RXA 02250153-341
SU02250153330RX1 02250153-330 SU02250153342RXA 02250153-342
SU02250153331RX1 02250153-331 SU02250153343RXA 02250153-343
Grade ACS - Activated carbon

SU02250153310ACS 02250153-310
SU02250153311ACS 02250153-311
SU02250153312ACS 02250153-312
SU02250153313ACS 02250153-313
SU02250153314ACS 02250153-314
SU02250153315ACS 02250153-315
SU02250153316ACS 02250153-316
SU02250153317ACS 02250153-317
SU02250153318ACS 02250153-318
SU02250153319ACS 02250153-319
SU02250153320ACS 02250153-320
69
AIR DRYERS
Replacement filter elements manufactured by Walker Filtration Ltd to fit TROCAIR

COMPRESSED ELEMENTS
housings.
ALTERNATIVE
trocair
Grade AC - activated carbon
JANUARY 2012

T1270 (grade) 1270 T1270 AC 1270
T1570 (grade) 1570 T1570 AC 1570
T3070 (grade) 3070 T3070 AC 3070
T6070 (grade) 6070 T6070 AC 6070
Grade:
V = X5 grade
M = X0 grade
S = XA grade
N = RX5 grade
Note: Please contact Walker Filtration Sales Department before ordering from this range.

ZANDER (PARKER) filter housings.
zander (parker)
Grade ZV 5 micron pre filter Grade ZZ 1 micron general purpose filter Grade ZY 0.1 micron oil filter
ZV 103 1030 V ZZ 103 1030 Z ZY 103 1030 Y
ZV 105 1050 V ZZ 105 1050 Z ZY 105 1050 Y
ZV 107 1070 V ZZ 107 1070 Z ZY 107 1070 Y
ZV 114 1140 V ZZ 114 1140 Z ZY 114 1140 Y
ZV 201 2010 V ZZ 201 2010 Z ZY 201 2010 Y
ZV 202 2020 V ZZ 202 2020 Z ZY 202 2020 Y
ZV 203 2030 V ZZ 203 2030 Z ZY 203 2030 Y
ZV 205 2050 V ZZ 205 2050 Z ZY 205 2050 Y
ZV 305 3050 V ZZ 305 3050 Z ZY 305 3050 Y
ZV 307 3075 V ZZ 307 3075 Z ZY 307 3075 Y
ZV 506 5060 V ZZ 506 5060 Z ZY 506 5060 Y
ZV 507 5075 V ZZ 507 5075 Z ZY 507 5075 Y
Grade ZX 0.01 micron dust filter Grade ZA Activated carbon

ZX 103 1030 X ZA 103 1030 A
ZX 105 1050 X ZA 105 1050 A
ZX 107 1070 X ZA 107 1070 A
ZX 114 1140 X ZA 114 1140 A
ZX 201 2010 X ZA 201 2010 A
ZX 202 2020 X ZA 202 2020 A
ZX 203 2030 X ZA 203 2030 A
ZX 205 2050 X ZA 205 2050 A
ZX 305 3050 X ZA 305 3050 A
ZX 307 3075 X ZA 307 3075 A
ZX 506 5060 X ZA 506 5060 A
ZX 507 5075 X ZA 507 5075 A
70 tel +44 (0)191 417 7816 fax +44 (0)191 415 3748
conditions of trade
1. Definitions 9.8 The Vendor shall be entitled to appropriate any payment made by the Purchase in settlement of such invoices or ac-
1.1 "Vendor" shall mean Walker Filtration Limited whose registered office is situated at Spire Road, Glover East, Washing- counts as the Vendor in its absolute discretion thinks fit notwithstanding any purposed appropriate to the contrary by
ton, Tyne & Wear, NE37 3ES. the Purchaser.
1.2 "Goods" shall mean all or any of the goods or materials which from time to time the Vendor contracts to supply. 9.9 Each of the foregoing sub-clauses shall, so far as the context permits, be read and construed independently of the
1.3 "Services" shall mean all or any of the services which from time to time the Vendor contracts to supply. other sub-clauses so that if one or more of them shall be held to be invalid this shall not affect the validity of the
1.4 "Purchaser" means the person, firm, company or other corporation who places an order with the Vendor or otherwise remaining sub-clause.
contracts with the Vendor for any of the Goods or services.
1.5 "Insolvency Event" shall mean all or any of the events that any distress or execution shall be levied upon any goods of 10. Guarantee
the Purchaser of if the Purchaser offers to make any arrangement with its creditors or commits any act of bankruptcy 10.1 Subject to the limitations contained in clause 10.3 and 11 below, the Vendor agrees that, any defects which under
of if a petition in bankruptcy be presented against the Purchaser of if any resolution or petition to wind up the proper use appear in the Goods within a period of 12 months of the Goods having been first used or within 15
Purchaser (other than for the purpose of amalgamation or reconstruction without insolvency) shall be presented or months of delivery whichever shall be the sooner and are due to faulty materials or workmanship, shall be made good
passed or if any petition for an administration order is presented or if a receiver or manager shall be appointed over by the Vendor either by repair or at the Vendor's option by replacement provided that the Purchaser complies with its
the whole or any part of the Purchaser's business or if the Vendor has any genuine reasons to believe the Purchaser is obligations under clause 6.5 above.
insolvent. 10.2 Subject to the limitations which appear in clause 10.3 and 11 below, the Vendor agrees that, any defects which under
proper use appear in goods upon which Services have been rendered within a period of 12 months of delivery and
2. Application are due to faulty workmanship, shall be made good by the Vendor by the provision of further Services on the goods
2.1 These conditions shall apply to all contracts, whether written, oral or implied for the supply of Goods or Services. originally supplied by the Purchaser provided the Purchaser complies with its obligations under clause 6.5 herein.
2.2 Any conditions of purchase or other terms provided by the Purchaser shall be of no effect whatsoever nor shall any 10.3 The Purchaser should note that the Goods contain disposable or replaceable parts including filter elements which will
variation or alteration of these conditions be of any effect unless made in writing and signed by or on behalf of the need replacing from time to time according to use. The life of any such parts and in particular any filter elements will
Vendor by a duly authorised signatory of the Vendor. depend on a large number of variable conditions and no guarantee can be given for their life.
2.3 No binding contract shall be created by the placing of an order by the Purchaser unless and until the Vendor's written
acknowledgement of the order shall have been posted or delivered which acknowledgement will be deemed to repeat 11. Exclusion of Liability
these conditions. Alternatively, in the event that no such acknowledgement is sent, at the time of acceptance of any 11.1 Except in the case of death or personal injury the Vendor's total liability to the Purchaser whether for negligence,
order for the Goods or Services by the Vendor a binding contract will be created subject to these conditions. breach of contract, misrepresentation or otherwise, shall in no circumstances exceed the cost of the defective, dam-
aged or undelivered Goods or Services determined by the Vendor's net invoice price to the Purchaser.
3. Quotations 11.2 Save as mentioned in Clause 10 and sub-clauses 11.1 and 11.3 hereof or prescribed by statute, the Vendor shall
Any quotation in whatever form given to the Purchaser is given subject to these conditions as an invitation to treat and be under no liability to the Purchaser whatsoever for any defect in, failure of, or unsuitability for any purpose of the
does not constitute an offer to sell. The Vendor will not accept any obligation in respect of any quotation dated over Goods or the Services or any part thereof whether the same be due to the act or omission, negligence or default of
thirty (30) days unless otherwise indicated in writing. the Vendor or its servants or agents, and all conditions, warranties and other terms whether expressed or implied,
statutory or otherwise, inconsistent with the provisions of this condition are hereby expressly excluded provided that
4. Prices nothing herein contained shall be construed as excluding or restricting the liability of the Vendor for death or personal
4.1 Subject to anything to the contrary contained in any quotation issued by the Vendor, prices for the Goods or Services injury resulting from the negligence of the Vendor.
are as referred to in the Vendor's price list current at the time of delivery and unless otherwise stated, are exclusive of 11.3 Where the Purchaser deals as a consumer within the meaning of that expression as defined in Section 12 of the Unfair
value added tax and any other similar tax. Contract Terms Act 1977 none of the statutory rights of the Purchaser are excluded by these terms and conditions and
4.2 The Purchaser shall have no right of set-off whether statutory or otherwise. the statutory rights of the Purchaser in the case of a consumer shall remain in full force and effect and are in no way
4.3 Unless otherwise expressly stated in writing by the Vendor, prices are exclusive of carriage, handling, packaging and affected by any of the provisions of these terms and conditions.
any insurance charges. 11.4 In no circumstances, shall the Vendor be liable for any economic loss or damage suffered by the Purchaser howsoever
4.4 Unless otherwise expressly stated in writing by the Vendor, all prices payable must be settled in the currency of the caused and whether foreseeable or contemplatible which, for the avoidance of doubt, shall be taken as including any
English Realm but if the Vendor agrees to accept foreign currency and does not specify an exchange rate the exchange loss of profits, business revenue, goodwill, anticipated saving, overhead and labour costs.
rate will be that of the Bank of England at the close of business on the day preceding the day on which the Vendor 11.5 The Vendor's prices are determined on the basis of the limits of liability set out in this clause. In the event that the
accepts the Purchaser's order. Purchaser requires the Vendor to accept a higher limit of liability, the Purchaser shall give written notice of this where-
upon the Vendor will accept such liability providing insurance can be obtained against that higher level of liability and
5. Payment and Default by Purchaser providing the cost of such insurance is borne by the Purchaser.
5.1 Subject to sub-clauses 5.2 and 5.3, the Purchaser shall pay the Vendor in full for the Goods or Services (as the case 11.6 Each of the foregoing sub-clauses shall, so far as the context permits, be read and construed independently of the
may be) within thirty (30) days of the date of the invoice. other sub-clauses so that if one or more of them shall be held to be invalid this shall not affect the validity of the
5.2 In the event that the Purchaser fails to make payment by the due date or otherwise commits a breach of these condi- remaining sub-clauses.
tions or if an Insolvency Event occurs, the Vendor may in its absolute discretion and without prejudice to any other
rights which it may have:- 12. Instructions
5.2.1 suspend all future deliveries or supplies to the Purchaser under the contract in question or under any other contracts Any Goods disposed of by the Vendor are complete with instructions for installation and use. The Purchaser agrees
and/or terminate all or any part of such contract(s) without liability upon its part. that the Goods will be installed and used in accordance with those instructions by suitably trained personnel. The Ven-
5.2.2 require payment in advance for any future deliveries. dor will assist the Purchaser or any ultimate user with further information relating to installation or use upon request.
5.2.3 (in the case of non-payment on or before the due date or on demand as mentioned in sub-clause 5.3 below) charge
interest on the amount due on a day to day basis at the rate of 2% per month compounded annually from the time of 13. Vendor's Indemnity
delivery or date of invoice whichever is the earlier until the date of actual payment, whether before or after judgement. Where the Purchaser shall supply goods or materials to the Vendor in connection with the supply of Services and any
5.3 Without prejudice to any other rights the Vendor may have by virtue of paragraph 5.2 the Vendor may demand im- defect or hazard appears in the goods or materials supplied then the Purchaser shall indemnify and keep indemnified
mediate payment of all sums whether or not due in the event that the Purchaser is the subject of an Insolvency Event. the Vendor from and against any and all loss, damage or liability suffered and legal fees and costs incurred by the
Vendor as a result of the defect unless the Purchaser can prove that the defect did not arise from any cause within his
6. Delivery and Collection control.
6.1 Subject to the provision of clauses 4.3 and 7; the Vendor may arrange delivery to the Purchaser's premises at the
Purchaser's request. In all other circumstances collection or delivery of Goods or goods upon which Services have been 14. Patent Infringement
rendered will be made at the Vendor's premises at which the Goods are made or Services rendered. The Purchaser warrants that any instructions, plans or designs furnished or given by it shall not be such as will cause
6.2 When delivery or collection takes place at the Purchaser's premises it will be the Purchaser's responsibility to ensure the Vendor to infringe any letters patent, copyright, registered design, right of confidence or trade mark in execution
delivery or collection can take place at the time and place specified or otherwise agreed. The Purchaser shall indemnify of the Purchaser's order and agrees to indemnify the Vendor against all claims, costs or other expenses incurred by the
the Vendor against any loss or expense incurred as a result of a breach of these obligations. Without prejudice to the Vendor in respect thereof.
foregoing, if the Vendor or its agents or employees agree to assist in the loading or unloading (as the case may be)
then the Vendor will not be liable for any loss or damage howsoever arising through any act, omission or negligence 15. General Lien
of any of its agents or employees. 15.1 The Vendor shall have a general lien over all goods or materials of the Purchaser in its possession for all monies due to
6.3 Although given in good faith delivery times for the supply of the Goods or the Services specified by the Vendor in its the Vendor or liabilities incurred by the Vendor upon whatever account and shall also be entitled to apply any monies
quotation or otherwise are intended as estimates only and are not therefore to be treated as being of the essence of of the Purchaser held by it under one contract to the discharge of monies due to it under any other contract. The
the contract or binding on the Vendor. The Vendor will not be liable to the Purchaser for any loss or damage (direct Vendor shall be entitled to charge rent and other expenses incurred during all periods in which a lien on goods or ma-
or indirect) occasioned by its failure (whether as a result of its negligence or otherwise) to deliver the Goods or the terials is being asserted. Further, if the Vendor exercises its right of lien over any goods or materials then if monies due
Services by the date or within the time stated and in no case shall delay be a ground for rejecting the same. are not paid within one month after it has first retained such goods or if the Purchaser is the subject of an Insolvency
6.4 The right to deliver the Goods or Services in parts is expressly reserved by the Vendor and these conditions shall apply Event, the Vendor shall have power, without giving notice, to sell the whole or part of such goods or materials to cover
to any such part or parts mutatis mutandis. the monies due and expenses of sale.
6.5 In the case of the alleged shortage in or damage to or defect in the Goods or goods upon which Services have been 15.2 For the avoidance of doubt, it is hereby declared that nothing in this clause shall effect the rights given to the Vendor
rendered:- by Sections 38-48 of the Sale of Goods Act 1979.
6.5.1 the Purchaser agrees to notify the Vendor in writing of any claim in respect thereof within seven days of its receipt
by the Purchaser in the case of shortage or damage or in the case of a defect within twenty eight days of the defect 16. Catalogues, Advertisements and Drawings
becoming apparent together with written evidence in support of such claim in relation to the date of receipt; and 16.1 Whilst the Vendor believes that all specifications, illustrations, performance data and other information contained in
6.5.2 the Purchaser agrees to allow the Vendor a reasonable opportunity to inspect any such goods before any use is made any drawings, catalogues, advertisements of other documents supplied by the Vendor are as accurate as reasonably
of them or alteration is made thereto and to keep them in good order and store them so as to prevent any damage possible, they do not constitute a description of the Goods and shall not be taken to be representations made by the
arising. Vendor and are not warranted to be accurate.
6.5.3 the Purchaser shall have no claim against the Vendor for shortage, damage or defects unless the requirements as to 16.2 The Purchaser shall not copy or otherwise reproduce any drawing, advertisements, catalogues or other documents
notification set out in this sub-clause 6.5.1, .2 and .3 are strictly complied with by the Purchaser. supplied by the Vendor without the Vendor's prior written consent.
6.6 In the event that the Purchaser is responsible for collecting the Goods or any goods upon which Services have been
rendered and such collection does not occur within seven days of the Purchaser having been informed that such 17. Intellectual Property
goods are ready for collection, the Vendor may charge the Purchaser for storage of any such goods until collection All intellectual property rights in the Goods or any drawings, specifications, designs prepared by the Vendor shall at all
occurs in addition to the price for the Goods or Services. times remain vested in the Vendor as the Vendor's absolute property and the Purchaser shall not reproduce or use all
or any of them without the Vendor's prior written consent.
7. Risk
7.1 The liability for Goods or goods upon which Services have been rendered shall pass to the Purchaser at the time they 18. Alterations and Modifications
are collected at the Vendor's works prior to loading or where the Vendor arranges delivery liability shall pass when the The Vendor may carry out from time to time and without notice to the Purchaser, alterations or improvements in
carrier collects the Goods or goods upon which Services have been rendered at the Vendor's premises prior to loading. construction or design, specification, materials or manner of manufacture of the Goods.
7.2 Without prejudice to the provisions of clause 7.1, in the event of any loss or damage to the Goods or goods upon
which services have been rendered whilst in the possession of the carrier, the Vendor shall take all reasonable steps, at 19. Force Majeure
the Purchaser's expense, to assist the Purchaser pursue any available claim against the carrier. Without prejudice to the generality of any of the foregoing conditions, the Vendor shall not be liable for any loss or
damage caused by the non-performance or delay in the performance of any of its obligations here-under if the same
8. Cancellation is occasioned by any cause whatsoever which is beyond the Vendor's control, including but not limited to Acts of
The Vendor shall be under no obligation whatsoever to accept any cancellation of an order once accepted. However, God, war, civil disturbance, requisitioning, import or export regulations, strike, lock-out or trade dispute, difficulties in
if the Vendor at its complete discretion agrees to accept any such cancellation or return, it may levy such charges as it, obtaining materials, breakdown of machinery, fire or accident. Should any such event occur the Vendor may cancel or
in its absolute discretion, sees fit. suspend this contract without incurring any liability for any loss or damage thereby occasioned.
9. Title 20. Frustration

9.1 The provisions of this clause shall apply until such time as the price of the Goods and/or Services has been paid in full If any contract to which these conditions apply is frustrated and/or the Goods in respect thereof cannot be delivered
or until payment has been made of all other sums owing to the Vendor at the date of this contract on any account for any cause whatsoever, it is expressly agreed that:
whatsoever or howsoever arising whichever occurrence shall be the later. 20.1 if any sum has been paid on account to the Vendor by the Purchaser and is repayable by operation of law the Vendor
9.2 The property in the Goods shall remain in the Vendor and the Purchaser shall hold the Goods as fiduciary agent and shall be entitled to deduct there from all expenses incurred in connection with the said contract; and
bailee for the Vendor. 20.2 if no sum has been paid on account the Purchaser shall be bound to pay the Vendor all expenses so incurred in con-
9.3 The Purchaser shall store the Goods separately from any other goods in such a manner that they can be identified nection with the said contract.
as the property of the Vendor and shall ensure that the Goods are not incorporated in or mixed in or used as part of
other goods. 21. Notices
9.4 Subject to sub-clauses 9.3, 9.5 and 9.6, the Purchaser shall be at liberty to sell or use the Goods in the ordinary course Any notice required to be served pursuant to these conditions shall be served as follows:-
of its business and the Vendor grants the Purchaser a license for this purpose. 21.1 notices to the Vendor: to its offices, Spire Road, Glover East, Washington, Tyne & Wear, NE37 3ES or such other
9.5 The purchaser shall account to the Vendor for the proceeds of any sale of the Goods and until such account is made, address as it may from time to time notify to the Purchaser;
the Purchaser will hold the proceeds of sale upon trust for the Vendor. The Purchaser shall ensure any monies received 21.2 notices to the Purchaser: to such address as the Purchaser may notify to the Vendor or, in default of notification, to
for the Goods are not mixed with other monies or paid into any overdrawn bank account. such address as appears on any order by the Purchaser, or if the Purchaser is a company, at the Vendor's option to the
9.6 The power of sale given to the Purchaser by sub-clause 9.4 above will automatically terminate if the Purchaser is the Purchaser's registered office.
subject of an Insolvency Event. An Insolvency Event shall be deemed to be a fundamental breach of contract. Further,
the Vendor may terminate the said power of sale at any time by written notice if the Purchaser is in default of payment 22. Governing Law
of any sum due to the Vendor. The construction, validity and performance of the contract shall be governed by and be interpreted in accordance with
9.7 At any time after termination pursuant to 9.6 above the Vendor may repossess the Goods and the Purchaser hereby English Law. The parties hereto agree to submit themselves to the non-exclusive jurisdiction of the English Courts for
grants to the Vendor an irrevocable license to enter upon any premises of the Purchaser for the purpose of so doing. the purposes of this contract.
Walker Filtration Ltd Walker Filtration Inc.
Birtley Road, Washington, 4748 Pacific Avenue
Tyne & Wear, NE38 9DA, UK Erie, PA 16506, USA
tel +44 (0) 191 417 7816 tel +1 814 836 2900
fax +44 (0) 191 415 3748 fax +1 814 836 7921
email sales@walkerfiltration.co.uk email usa@walkerfiltration.com
web www.walkerfiltration.com web www.walkerfiltration.com
Walker Filtration Pty Ltd Walker Filtration SA (Pty) Ltd

3A Kia Court, Preston Unit 5, New Era Ext. 1,
Victoria 3072, Australia Springs, ZA-1559, South Africa
tel +61 (0)3 9480 0750 tel +27 (0) 11 813 1351
fax +61 (0)3 9495 1044 fax +27 (0) 11 813 1356
email sales@walkerfiltration.com.au email info@walkerfiltration.co.za
web www.walkerfiltration.com.au web www.walkerfiltration.com
WFL-12-04

Product Range & Price Guide: Effective From January 2012

Uploaded by

Copyright:

Available Formats

Product Range & Price Guide: Effective From January 2012

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Range & Price Guide: Effective From January 2012

Uploaded by

Copyright:

Available Formats

Product Range

& Price Guide

Filtration and treatment of your compressed air system is critical to:

Guarantee optimum performance

Water condensate is also a significant problem which needs to be removed in order to

Price Guide effective from 1st January 2012.

Compressed Air Filters Water Separators 12

Compressed Air Dryers Pro Dry 35

Accessories Drain Valve Equipment 39

Filter Elements Previous Walker Filter Elements 43

vacuum for maximum flow rate, multiply model flow rate

Dewpoint °C (°F) -40 (-40) -70 (-94)

convert flow rate

recommended air flow rate

BS 4575 Maximum Recommended Air Flow Rates at 7 barg (100 psig)

Particles Water Oil

Filter Grade GRADE X25 GRADE X5 GRADE X1 GRADE XA GRADE AC

High Efficiency Filtration 1,2,1

ISO 8573 - compressed air purity standard

ISO 12500 - introducing a new series of international

Other Applicable Standards

The technologically advanced design

Filter Element Features

Double O-ring secures against

Lower annular location ring

For compressed air installations where water contamination is a problem,

A028 WS ¼ 42 25 70 25 191 90 0.7

A128 CWS 1¼ 476 280 122 42 380 150 2.3

A A Replacements and spare parts (refer to pages 38 – 42)

30mm Float operated drain valve

coarse filtration X25

Replacements and spare parts (refer to pages 38 – 42)

X25 element Differential Float operated drain valve

A018 X5 ¼ 13.6 8 50 18 152 60 0.3 E0304 X5 1

See page 12 for flanged filter packaging

Replacements and spare parts (refer to pages 38 – 42)

X5 element Differential Float operated drain valve

A391 X1 DN80 2160 1270 450 265 1205 700 58 E139 X1 1

Replacements and spare parts (refer to pages 38 – 42)

X1 element Differential Float operated drain valve

XA high efficiency filtration

A018 XA ¼ 13.6 8 50 18 152 60 0.3 E0304 XA 1

See page 12 for flanged filter packaging

Replacements and spare parts (refer to pages 38 – 42)

XA element Differential Float operated drain valve

A018 XA to A391 XA to technical notes

activated carbon filtration AC

A391 AC DN80 2160 1270 450 265 1205 700 58 E139 AC 1

Replacements and spare parts (refer to pages 38 – 42)

AC element Semi-automatic drain valve

XAC 2 stage duplex filtration

model size Kg price model elements

Replacements and spare parts (refer to pages 38 – 42)

D028 XAC to D109 XAC

Replacements and spare parts (refer to pages 38 – 42)

HT high temperature dust filtration

HT25 (grade) ¼ 35 20 85 18 170 75 1.7 E50 (grade)

Replacements and spare parts (refer to pages 38 – 42)

alloy high pressure filters 20 barg